Specifications

34
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
100" CUTTING DECK, MODEL 31101
REQUIRED HP OF MOWING UNIT
Greater than 33 hp (24.6 kw)
WIDTH OF CUT
100" (254cm), by five blades
HEIGHT OF CUT
1”-5” (25 - 127 mm) adjustable in 0.25” (6 mm) increments
DECK CONSTRUCTION
Center deck with two wing decks; Welded .120" (11 gauge) high strength steel with steel .180" (7 gauge) stiffener plates and .1046" (12 gauge) chambers.
DISCHARGE
Rear Discharge – complete width of deck.
WING DECK ARTICULATION
15 degrees, up or down.
SPINDLE ASSEMBLY
Ductile cast iron 9" (23 cm) diameter conical spindle housing; Dual greaseable tapered roller bearings; Spindle shaft is 1.25" (3.2 cm) diameter, solid cold finished steel, and
splined connection between spindle shaft and pulley; Welded blade retainer plus anti-scalp cups.
CUTTER DRIVE
Isolation mounted, PTO driven gearbox with 1.25:1 spiral bevel gears. “B” section belt drive to all spindles.
BLADES
Wing Decks: 25.2" (64cm) long,.25" (6mm) thick, 2.5 (63mm) wide, heat treated steel blade in each wing; Center Deck: Three 18"(45.7cm) long, .25" (6mm) thick, 2.5" (63mm)
wide, heat treated steel blades.
BLADE TIP SPEED
16,000 ± 1,000 ft/min at 3250 engine rpm
DECK SUSPENSION
Center deck is supported via 4 vertically suspended chains to the frame of the machine. Wing decks are supported by pin connections to center deck and castor wheels on the
ground. Hydraulic deck lift includes load holding check valves and gravity lower.
CASTOR WHEELS
Four 8 x 3.50-4, 4-ply, smooth, pneumatic, sealed precision ball bearings. Tensioning caps, made from impact modified thermoplastic alloy, are used to hold the castor wheels on
the castor arms.
BELT IDLER
Fixed and spring loaded idlers.
DECK SKID
Replaceable, bolt-on, non-marking UHMW skid on both sides.
DECK ANTI-SCALP ROLLERS
5
ANTI-SCALP CUPS
Anti-scalp cup located on each blade spindle.
DECK COVERS
Steel and plastic with rubber latch connectors.
CUTTING DECK DEPTH
4.25" (108 mm)
WING DECK TRANSPORT
LOCKS
Manual latches (standard)
WEIGHT
Approximately 790 lbs (358 kg)
WIDTH
Mow: 108" (274 cm) Transport: Overall width with wing decks raised: 88 in (223.5 cm); center deck is 54.5 in (138.4 cm) wide and 5" (12.7 cm) off ground when raised.
OPTIONAL ACCESSORIES
Leaf Mulching Kit (Model 31105)
CERTIFICATION
American National Standard ANSI B71.4-2012. European standard per ISO EN 5395 , CE approved.
MOWING RATE
Mow up to 8.0 acres/hr (3.2 hectare/hr) at 8 mph (12.9 km/hr). Assumes no overlap and 100% efficiency.
MOWING POSITION
100” (254 cm) Mowing Width
108” (274 cm) Total Width
TRANSPORT/TRAILERING POSITION
54.5” (138.4 cm)
67” (170.2 cm)
73.5” (186.7 cm)
18”
(45.7 cm)
12”
(30.5 cm)
88” (223.5 cm) Total Width
5” (12.7 cm)
Groundsmaster
®
7200 Series Specifications
*