Design Guide

ManualsBrandsToro ManualsGolf Lighting ProductsToro Twilight Golf Cup

ank you for purchasing a Toro Twilight Golf Post Light (TWGP). e lights are ideal for

illuminating practice putting greens, among other things. e Setup Guide is provided to assist

you with determining the number of lights needed, how to lay them out properly, make all wire

connections, install them into the ground, and make light adjustments.

Lighting System Components

Equipment Part Number Warranty Period

Transformers TWGP-TRANS-360SS (Wall Mount)

TWGP-TRANS-360DB (Direct Burial)

TWGP-TRANS-1120SS (Wall Mount)

Limited lifetime warranty for repair or

replacement.

Hub TWGP-HUB

(1 hub for 4 wire runs, 24 light xtures max.)

3 year

Wire TWGP-WIRE-12-2-500 (500’ per spool)

Lightpost stake TWGP-STAKE 3 year

Twilight Golf Postlight TWGP-STAR36-12-L5

Limited lifetime for repair or replacement.

is warranty covers all parts and

components with the exception of the lamp.

LED lamp 5 year

TWILIGHT GOLF POST LIGHT

Setup Guide

TWILIGHT GOLF POST LIGHT

Setup Guide

TWGP-STAR36-12-L5

UNIQUE LIGHTING

Figure 1

(not to scale)

“Home Run” Line

Existing GFCI

Outlet

TWGP-HUB

TWGP-TRANS-360SS

Guidelines

• Connect no more than 6 TWGP lights to each

wire run.

• Maximum 4 wire runs per hub.

• Bring all wire runs into a TWGP-HUB (close

to the postlight installation) and splice together

using the supplied water-proof connections.

From the TWGP-HUB, run a single “Home

Run” cable to the transformer location.

• Lights should be roughly 15’ apart.

~15´

Lighting System Sample Layout

TWGP-WIRE-12-2-500

CAUTION: Consult with a qualied electrician and local electrical codes

before installing any electrical product.

Summary of content (6 pages)

PAGE 1
TWILIGHT GOLF POST LIGHT Setup Guide Thank you for purchasing a Toro Twilight Golf Post Light (TWGP). The lights are ideal for illuminating practice putting greens, among other things. The Setup Guide is provided to assist you with determining the number of lights needed, how to lay them out properly, make all wire connections, install them into the ground, and make light adjustments.
PAGE 2
Determine the Number of Lights Needed and the Spacing Directions Example 1. Use a measuring wheel to determine the length of the perimeter of the area to be illuminated. 2. The lights should be roughly 15’ apart. Divide the perimeter by 15. Perimeter measures 352’. 3. Round that number UP to the nearest whole number. That is the number of lights needed. 4. Divide the perimeter by the number of lights. That is how far apart the lights should be installed. Divide 352 by 15. Equals 23.46. Round 23.
PAGE 3
Installing the Twilight Golf Post (TWGP-STAKE) WARNING: Risk of electric shock. Turn off power before servicing. Install all post lights 10 feet (3.05m) or more from a pool, spa, or fountain. Figure 5 ToroCap: TWGP-ELECREC 1. Remove sod and excavate a 12” deep (below aeration depth) trench for the UF supply line cable or conduit and lightpost. The lightpost requires a 10” diameter hole to facilitate installation to a depth of 18”. 3 2 Insert wire nuts into grease caps and latch.
PAGE 4
Adjusting the Twilight Golf Post Light (TWGP-STAR36-12-L5) Figure 8 adjust head angle Head Angle 1. Loosen the brass nut (Figure 8) turning it counter-clockwise. 2. Adjust the head to the desired angle. 3. Retighten the brass nut to hold desired angle. Figure 9 loosen Oribtal lock nut to adjust direction Direction 1. Loosen the Orbital lock nut (Figure 9) around the light post. 2. Rotate the head only of the TWGP-STAR to desired direction. Do not rotate the lightpost as damage may occur. 3.
PAGE 5
Hub Wiring Illustration Figure 16 (not to scale) 5-amp fuse wires extra 5-amp fuses in the lid TWGP-HUB zip-tie to light fixtures 1 2 from transformer 3 4 CAUTION: DO NOT OVERLOAD CABLE OR TRANSFORMER. Maintain polarity at all times. Consult with a qualified electrical contractor and local eletrical code authorities before installing any electrical product.
PAGE 6
Safety and Maintenance Notes • Use with low-voltage, outdoor lighting system only. • Lamp is hot when lit. Do not touch when lamp is on. • Allow fixture to cool before touching or re-lamping fixture. • Do not operate fixture if cover shield is damaged or missing. • Do not submerse in water. • Clean fixture with mild soap only. Do not use acid or any other solvent base cleaner. • Keep away from materials, structures, or landscapes that may burn.