Installation Guide
2
PRODUCT SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS
Max. Flow Rate: 1.8 GPM (6.8 LPM) at 60 PSI Ceramic cartridge
ASME A112.18.1/CSA B125
Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
NSF 61-9
Polished chrome or stainless steel nish
ASSEMBLY INSTRUCTIONS
1.
Shut off water supplies. Remove old faucet.
Clean sink surface in preparation for new
faucet. Check for the proper thickness of
the sink. If installing the faucet without the
escutcheon, begin with step 2. If installing
the faucet with the escutcheon, begin
with step 3.
W/O escutcheon
1/16 in.min.
1-1/2 in. max.
Ø1-3/8 in.min.
Ø1-1/2 in. max.
1/16 in min.
1 in. max.
Ø1-3/8 in. min.
Ø1-1/2 in. max.
With escutcheon
1
5.
Insert the hose (1) supply lines (2 and
3) and quick connect hose (4) one by
one through the hole of the base (5).
The sprayer hose (1) should be placed
on the left side inside the base. Carefully
insert the hoses into the base. Place the
faucet assembly onto the base (5) as
shown in the above gure.
1
2
3
4
5
5
2.
Optional No Escutcheon
Installation:
Insert the base (1) into sink.
NOTE: “Front” on the base (1) must face
the front of the sink. The two mounting
plates (2) on the base (1) must be loose
and movable during the installation of
the base (1).
1
2
2
6.
Secure the faucet assembly (1) by
tightening the set screw with the
provided hex wrench (2, Hex: 2.5 mm).
1
2
6
3.
Optional Escutcheon Installation:
Place the escutcheon (1) and the gasket
(2) on the sink. Insert the base (3) into
escutcheon (1).
NOTE: “Front” on the base (3) must face
the front of the sink. The two mounting
plates (4) on the base (3) must be loose
and movable during the installation of
the base (3).
NOTE: If the sink is uneven, use silicone
under the gasket (2).
1
2
3
4
1
3
7.
Push the quick connector (1) rmly
upward and attach it to the receiving
block (2). Pull down moderately to
ensure the connection has been made.
If it is necessary to remove the quick
connector (1), squeeze the tabs on the
quick connector and then pull down to
disconnect.
1
2
7
4.
Secure the base (1) and escutcheon (2) so
that they can not move, then turn the
screws with the provided hex wrench
(3, Hex: 6.0mm) clockwise, as shown Fig 1.
When the mounting plates (4) make
contact with the sink (5), continue to turn
the screw with the provided hex wrench
(3, HEX: 6.0mm) clockwise, as shown Fig 2,
until the base (1) is completely tightened
and secured, as shown Fig.3.
Fig 1
Fig 2
Fig 3
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
4
8.
Install the weight clip (1) at the point of
the hose marking “weight here”. Insert
the weight (2) onto the clip (1) by sliding
it down onto the clip (1).
1
1
2
2
8
www.homewerksww.com