Specification

ManualsBrandsTosca ManualsBathSingle Hole 4”-Single Slide Handle LED Bathroom Faucet with pop-up drain and deck plate in Brushed Nickel

Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • HomewerksWW.com

03-02-2020

BATHROOM FAUCET WITH LED LIGHT

AND PUSH POP-UP DRAIN ASSEMBLY

TBD2-CH-T – Polished chrome

TBD2-BN-T – Brushed nickel

TBD2-MB-T – Matte black

PACKAGE AND HARDWARE CONTENTS

PART DESCRIPTION

QUANTITY

A Faucet body

B Deckplate and gasket

C Mounting nut

D Metal washer

E Rubber washer

F Push pop-up drain assembly

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble,

operate or install the product.

WARNING

• Protect your eyes with safety glasses when cutting or soldering water

supply lines.

CAUTION

• If you solder the joints during installation, the seats, cartridges, and washers

must be removed before using a ﬂame or the warranty will be voided on

these parts.

• Cover the drain to avoid losing parts.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare

parts with package and hardware contents list. If any part is missing or damaged, do

not attempt to assemble the product. Contact customer service for replacement

parts.

Estimated Assembly Time: 30 minutes

Tools required for assembly (not included): adjustable wrenches, groove joint

pliers, pipe wrench, Phillips screwdriver, supply lines, thread seal tape, silicone.

Installation may vary depending on how the previous faucet was installed. Sup-

plies necessary for the installation of the faucet are not all included; however,

they are available wherever plumbing supplies are sold.

Prior to beginning installation, turn off the hot and cold water lines, then turn

on the old faucet to release built-up pressure. When installing the new faucet,

hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections

that are too tight will reduce the integrity of the system.

Need Help? Please call our toll-free line at (877) 319-3757 (7:30 am to 4:30 pm CST) for additional assistance or service.

Summary of content (8 pages)

PAGE 1
® BATHROOM FAUCET WITH LED LIGHT AND PUSH POP-UP DRAIN ASSEMBLY TBD2-CH-T – Polished chrome TBD2-BN-T – Brushed nickel TBD2-MB-T – Matte black PACKAGE AND HARDWARE CONTENTS PART DESCRIPTION QUANTITY A Faucet body 1 B Deckplate and gasket 1 C Mounting nut 1 D Metal washer 1 E Rubber washer 1 F Push pop-up drain assembly 1 B C A F D E SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.
PAGE 2
PRODUCT SPECIFICATIONS Max. Flow Rate: 1.2 GPM (4.5 LPM) at 60 PSI Ceramic cartridge ASME A112.18.1/CSA B125 NSF 61-9 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces Polished chrome, brushed nickel or matte black finish Total weight: 3.42 lbs. ASSEMBLY INSTRUCTIONS 1. urn off water at the supply valve T under the sink or at the main water supply. Disconnect the supply lines and remove the old faucet. 5.
PAGE 3
ASSEMBLY INSTRUCTIONS 9. Attach each of the remaining ends of the water supply lines to the hot (red stripe) and cold water (blue stripe) lines coming from the metal shank (9.1) on the faucet body (A). Hand tighten the supply line connection. Repeat for the second supply line. 10. After installation is complete, turn on the water supply and adjust the 10 handle (10.1) on the faucet body (A) to the warm position where it mixes both hot and cold water.
PAGE 4
ROUGH-IN 6-1/8" 4-5/8" 2-5/8" 2-5/16" 7-17/16" 1-29/32" 1-1/4-20UN 4-21/32" 6-15/32" REPLACEMENT PARTS For replacement parts, call our customer service department at (877) 319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
PAGE 5
® GRIFO DE BAÑO CON LED Y DRENAJE CON TAPÓN A PRESIÓN TBD2-CH-T – Acabado de cromo pulido TBD2-BN-T – Acabado niquel pulido TBD2-MB-T – Acabado en negro mate NSF/ANSI-61 PAQUETE DE HARDWARE Y CONTENIDO ADA PARTE DESCRIPCIÓN CANTIDAD A Cuerpo del grifo 1 B Placa de cubierta y junta 1 C Tuerca de montaje 1 D Arandela metálica 1 E Arandela de caucho 1 F Drenaje con tapón a presión 1 B C A F D E INFORMACIÓN SOBRE LA SEGURIDAD PRECAUCIÓN • Si soldar las articulaciones durante la ins
PAGE 6
ESPECIFICACIONES DEL PRODUCTO ESPECIFICACIONES ESPECIFICACIONES Max. Caudal: 1,2 GPM (4.54 LPM) a 60 PSI Cartucho de cerámica ASME A112.18.1/CSA B125 NSF 61-9 Fabricado a incluir no más de 0,25% de contenido de plomo promedio ponderado en superficies mojadas Cromo pulido, níquel cepillado o negro mate acabado Peso total: 3.42 lbs. INSTRUCCIONES DE MONTAJE 1. Cierre la llave de paso debajo del lavabo o la llave principa de provisión de agua.
PAGE 7
INSTRUCCIONES DE MONTAJE 9. Conecte cada uno de los extremos restantes de los tubos de suministro de agua a las salidas de agua caliente (raya roja) y fría (raya azul) procedentes del vástago metálico (9.1) en el cuerpo del grifo (A). Apriete a mano la conexión a la salida de agua. Repita para la segunda salida de agua. 10. Una vez completada la instalación, abra el suministro de agua y ajuste la palanca (10.1) en el cuerpo del grifo (A) a la posición tibia donde mezcla agua fría y caliente.
PAGE 8
ÁSPERA EN 6-1/8" 4-5/8" 2-5/8" 2-5/16" 7-17/16" 1-29/32" 1-1/4-20UN 4-21/32" 6-15/32" LISTA DE REPUESTOS Para piezas de repuesto, llame a nuestro departamento de servicio al cliente al (877) 319-3757, 7:30 a.m.- 4:30 p.m. CST, Lunes - Viernes.