® Tecra M7 Series User’s Guide If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 209 in this guide.
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Model: Tecra® M7 Series Recordable and/or ReWritable Drive(s) and Associated Software Warranty The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available.
Critical Applications The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interference received, including interference that may cause undesired operation. Contact either: ❖ Toshiba’s Support Web site at pcsupport.toshiba.com.
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can.
provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer. Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Wireless LAN and Your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers.
documentation that comes with the product. This device complies with the following radio frequency and safety standards. Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s Web site www.hc-sc.gc.ca/rpb.
EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: Supplementary *The product complies with the Information: requirements of the Low Voltage Directive 72/23/EEC, the EMC Directive 89/336/ EEC and/or the R&TTE Directive 1999/ 05/EEC. This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Taiwan Article 14 Article 17 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Any use of low power radio frequency electric machinery shall not affect aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued.
2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4DSOF4 (4) 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3.
The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use only. Radio Approvals for Wireless Devices NOTE The following information is dependent on what type of wireless device is in your computer.
Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ Belgique: Deutschland: France: Italia: Nederland: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT.
802.
❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA Turbo Mode (5 GHz) Canada USA Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.
In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth wireless technology on board airplanes, or ❖ In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
Taiwan Article 14 Article 17 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Any use of low power radio frequency electric machinery shall not affect aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued.
2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4FH1 (4) 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3.
Optical Drive Safety Instructions The HD DVD-ROM and multi-function drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Never attempt to disassemble, adjust or repair a HD DVD, CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury.
Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. ©2006 by Toshiba America Information Systems, Inc. All rights reserved. Export Administration Regulation This document contains technical data that may be controlled under the U.S.
Trademarks Tecra is a registered trademark of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. Secure Digital and SD are trademarks of the Secure Digital Association. xD-Picture Card is a trademark of Fuji Photo Film Co. Ltd.
Contents Introduction................................................................................ 35 This guide ...............................................................37 Safety icons ............................................................37 Other icons used...............................................38 Other documentation ..............................................38 Service options .......................................................39 Chapter 1: Getting Started..................
Contents 27 Using the computer for the first time ......................51 Opening the display panel .................................51 Your computer’s features and specifications ....52 Turning on the power........................................53 Adding memory (optional) ......................................54 Installing a memory module .............................54 Hard Drive Recovery Utilities ..................................55 Creating Recovery CDs/DVDs ...........................
Contents Customizing your computer’s settings..............85 Caring for your computer........................................86 Cleaning the computer ......................................86 Moving the computer........................................86 Using a computer lock ......................................87 Chapter 2: Learning the Basics................................................. 88 Computing tips .......................................................88 Using the keyboard ..............
Contents 29 Toshiba’s online resources ...................................108 Chapter 3: Mobile Computing.................................................109 Toshiba’s energy-saver design..............................109 Running the computer on battery power ..............109 Battery Notice .................................................110 Power management ........................................111 Using additional batteries ...............................111 Charging batteries.......................
Contents The Internet ....................................................139 The World Wide Web ......................................139 Internet Service Providers...............................139 Connecting to the Internet ..............................139 Surfing the Internet.........................................140 Internet features..............................................141 Uploading to, and downloading files from, the Internet ...............................................
Contents 31 Setting passwords ................................................163 Using an instant password..............................163 Setting a user password .................................164 Disabling a user password..............................164 Using a supervisor or user password ...................165 Setting a supervisor password........................165 Deleting a supervisor password......................166 TOSHIBA Password Utility ....................................
Contents TOSHIBA Button Controls .....................................191 CD/DVD Drive Acoustic Silencer ...........................192 TOSHIBA Accessibility ..........................................193 TOSHIBA Mobile Extension...................................194 Fingerprint Authentication Utility...........................195 Fingerprint utility limitations ...........................195 Fingerprint Enrollment ....................................196 Fingerprint Logon ...............................
Contents 33 PC Card problems...........................................232 Printer problems .............................................236 Modem problems............................................237 Wireless networking problems .......................238 DVD operating problems.......................................241 Develop good computing habits ...........................244 Data and system configuration backup in Windows XP .............................................
Contents Appendix B: Power Cord/Cable Connectors..........................263 Appendix C: Using ConfigFree™ with your Toshiba Computer.............................................................264 Getting Started......................................................265 Starting ConfigFree .........................................265 ConfigFree Utilities................................................267 Connectivity Doctor ........................................267 Search for Wireless Devices ......
Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go. NOTE This notebook is compatible with European Union Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE.
NOTE Introduction Certain Microsoft® software product(s) included with this computer may use technological measures for copy protection. IN SUCH EVENT, YOU WILL NOT BE ABLE TO USE THE PRODUCT IF YOU DO NOT FULLY COMPLY WITH THE PRODUCT ACTIVATION PROCEDURES.
Introduction This guide 37 This guide This guide introduces the computer’s features. You can: ❖ Read the entire guide from beginning to end. ❖ Skim through and stop when a topic interests you. ❖ Use the table of contents and the index to find specific information. Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data.
Introduction Other documentation Other icons used Additional icons highlight other helpful or educational information: TECHNICAL NOTE: This icon indicates technical information about the computer. HINT: This icon indicates helpful hints and tips. DEFINITION: This icon indicates the definition of a term used in the text.
Introduction Service options 39 Service options Toshiba offers a full line of optional service programs to complement its limited warranty. Toshiba’s standard limited warranty, extended warranty, and service upgrade terms and conditions are available at warranty.toshiba.com. To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com.
Chapter 1 Getting Started This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations. Creating a computer-friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.
Getting Started Selecting a place to work 41 To keep your computer in prime operating condition, protect your work area from: ❖ Dust, moisture, and direct sunlight. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ❖ Extreme heat, cold, or humidity.
Getting Started Selecting a place to work Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately: 1. Turn off the computer. 2. Disconnect the AC adaptor from the power plug socket and computer. 3. Remove the battery pack.
Getting Started Selecting a place to work ❖ 43 Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers. Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files. Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could damage the disc and possibly lose data. ❖ Scan all new files for viruses.
Getting Started Setting up your computer Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Standby mode). In this condition, observe the following: ❖ Never cover your computer or AC adaptor with any object. ❖ Never place your computer or AC adaptor near a heat source, such as an electric blanket or heater.
Getting Started Setting up your computer 45 Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. NOTE The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices. The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software. 1 From the Welcome screen click Next to enter the Setup Wizard.
Getting Started Registering your computer with Toshiba 6 Follow the remaining screen prompts to complete the setup process. Once you click the final screen, your computer restarts automatically. Registering your computer with Toshiba Product registration is strongly recommended, and allows Toshiba to send you periodic updates, announcements, and special offers applicable to your product. Product registration can be completed during the initial start up process of your computer.
Getting Started Connecting to a power source 47 ❖ Connect a local printer (see “Connecting a printer” on page 72) ❖ Connect an optional external disk drive (see “Connecting an optional external diskette drive” on page 74) ❖ Install PC Cards (see “Using PC Cards” on page 149) Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery.
Getting Started Connecting to a power source Power cord/cable AC adaptor AC adaptor cord (Sample Illustration) Power cord/cable and AC adaptor To connect AC power to the computer: 1 Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. 5.375 x 8.
Getting Started Connecting to a power source _ + 2 49 Plug the AC adaptor cord into the DC-IN on the back of the computer. (Sample Illustration) Connecting the AC adaptor cord to the computer 3 Connect the power cord/cable to a live electrical outlet. The AC power light on the indicator panel glows green. Never attempt to connect or disconnect a power plug with wet hands. Failure to follow this instruction could result in an electric shock, possibly resulting in serious injury.
Getting Started Charging the main battery NOTE If the AC power light flashes amber during charging, either the main battery is malfunctioning, or it is not receiving correct input from the AC power supply. Disconnect the AC power cord/cable and remove the main battery pack. See “Changing the main battery” on page 121 for information on replacing the main battery. Charging the main battery Your computer came with its battery already installed.
Getting Started Using the computer for the first time 51 Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Slide the display latch to the right. 2 Lift the display panel. (Sample Illustration) Opening the display panel NOTE When opening or closing the LCD display panel, place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the LCD display panel.
Getting Started Using the computer for the first time Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate.
Getting Started Using the computer for the first time 53 Turning on the power To turn on the computer: 1 Make sure any external devices (such as the AC adaptor, if you plan to use AC power rather than battery power) are properly connected and ready. 2 Check to ensure that all optical drives are empty. 3 Slide and hold the power switch until the on/off light on the system indicator panel glows green—about one second.
Getting Started Adding memory (optional) Adding memory (optional) HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com. Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data. NOTE Before adding external devices or memory, Toshiba recommends setting up your software.
Getting Started Hard Drive Recovery Utilities 55 Hard Drive Recovery Utilities Your computer has been configured with a hard disk partition to allow you to recover your hard disk drive or reinstall selected applications and software features or utilities. NOTE It is strongly recommended that you create recovery CDs/ DVDs before using your system. For more information on creating Recovery media see “Creating Recovery CDs/DVDs” on page 55.
Getting Started Hard Drive Recovery Utilities NOTE The system will prompt you to insert the appropriate number of blank CDs or DVDs to copy the Hard Drive Recovery Utilities. If your optical disc drive is not writable, contact Toshiba Customer Support to obtain the Recovery media for your system. The Toshiba Global Support Centre in the United States is (800) 457-7777, outside the United States it is (949) 859-4273.
Getting Started Hard Drive Recovery Utilities 57 5 Insert the first blank CD or DVD into your computer’s CD/DVD writable drive when prompted. 6 Follow the on-screen prompts for completing the copy process. For more information on using the Recovery media you have created with the preceding steps see “Hard Disk Drive Recovery using the Recovery media” on page 62.
Getting Started Hard Drive Recovery Utilities Recovering the original factory image (recommended recovery method) Recovering a hard disk drive to its factory default setting deletes all partitions on the hard disk drive and your information will be lost. Be sure to save your work to external media first. 1 On the Toshiba Recovery Wizard screen, select Recovery of Factory Default Software, then click Next. The Recovery of Factory Default Software screen appears.
Getting Started Hard Drive Recovery Utilities 59 Erasing the hard disk The Recovery Wizard allows you to delete all data and partitions from the hard disk. To delete the data and partitions from your hard disk: 1 On the Toshiba Recovery Wizard screen, select Erase the hard disk, then click Next. 2 The next screen lists the two methods you can choose: ❖ Delete all data and partitions from the hard disk— This option deletes all of the data on the hard disk without overwriting the HDD.
Getting Started Hard Drive Recovery Utilities 4 Click Next to begin deleting the HDD. When the process is completed, a message displays informing you that the HDD has been deleted. 5 Press any key on the keyboard to restart the computer. Recovering the C: partition of the HDD without changing the current partition size Recovering the C: drive to its factory default setting reformats your drive and your information on the recovered drive will be lost.
Getting Started Hard Drive Recovery Utilities 61 Recovering the C: partition with a user specified size Resizing and recovering your C: drive to its factory default setting reformats all partitions on the HDD (for example, if you created a D: drive, it will be deleted during the recovery process) and your information will be lost. Be sure to save your work to external media first. To resize and recover your C: drive: 1 On the Toshiba Recovery Wizard screen, select “Recovery of factory default.
Getting Started Hard Drive Recovery Utilities Hard Disk Drive Recovery using the Recovery media If you need to recover your computer to its default factory state, you can rebuild the system using your Hard Drive Recovery Utilities. To recover your hard disk drive using the utilities burned to CDs or DVDs (refer to “Creating Recovery CDs/DVDs” on page 55): 1 Insert the first recovery CD or DVD into your CD/DVD drive and power on the computer. 2 When the initial screen displays, press F12.
Getting Started Hard Drive Recovery Utilities 63 Recovering the original factory image (recommended recovery method) Recovering a hard disk drive to its factory default setting deletes all partitions on the hard disk drive and your information will be lost. Be sure to save your work to external media first. 1 Select “Recovery of Factory Default Software.” Click Next. 2 Select “Recover to out-of-the-box-state.” Click Next.
Getting Started Hard Drive Recovery Utilities 2 Select “Recover without the hard drive partitions.” Click Next. ❖ A confirmation message appears, reminding you that all information on the C: drive will be lost during the recovery process. Be sure you have saved your work to external media before proceeding. 3 Click Next to begin the restoration. Once complete, a message displays that the HDD has been recovered. 4 Press any key on your keyboard to restart the computer.
Getting Started Hard Drive Recovery Utilities 65 Checking the HDD operating status After restoring your hard disk drive, you can check its status as follows: 1 Click Start, and then click Control Panel. 2 Double-click the Administrative Tools icon. 3 Double-click the Computer Management icon. 4 Click Disk Management. 5 Highlight the hard disk drive in the Volume list to display its status in the lower portion of the screen.
Getting Started Using the TouchPad™ Using the TouchPad™ The TouchPad™, the small, smooth, square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you would like to move the cursor: ❖ To move the cursor to the top of the page, push your finger forward on the TouchPad. ❖ To move the cursor to the bottom of the page, drag your finger toward yourself.
Getting Started Using the TouchPad™ 67 Scrolling with the TouchPad™ There are two active regions on the TouchPad™ that allow you to scroll as you would with any wheel device on a mouse or trackball. To scroll vertically, run your finger up or down along the right edge of the TouchPad. To scroll horizontally, run your finger along the bottom edge of the TouchPad. This feature can be disabled or changed in the Mouse Properties dialog box.
Getting Started Using the TouchPad™ 4 Click the TouchPAD ON/OFF tab. The TouchPAD ON/OFF tab view window appears. (Sample Image) TouchPAD ON/OFF screen 5 Select Disable or Enable, whichever is appropriate. 6 Click Apply. 7 Click OK. The Mouse Properties window closes. 8 Close the Printers and Other Hardware window. 9 Close the Control Panel window. You can also use a hot key to disable or enable the TouchPad. See “Disabling or enabling the TouchPad” on page 261. 5.375 x 8.375 ver 2.
Getting Started Using external display devices 69 Using external display devices Your computer comes with a built-in LCD display, but you can also connect an external display device to an available video port, as follows: ❖ An external monitor or projector via the RGB (monitor) port ❖ A TV, VCR, or DVD recorder via the S-video (TV-out) port Before connecting an external monitor or video projector, configure your computer for the type of device you are connecting.
Getting Started Using external display devices 2 While holding down Fn, press F5 repeatedly until the setting you want takes effect. Briefly pause each time you press the F5 key to allow time for the display to change.
Getting Started Using an external keyboard 71 Adjusting the quality of the external display To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps. TECHNICAL NOTE: To use one of the simultaneous modes, you must set the resolution of the internal display panel to match the resolution of the external display device.
Getting Started Connecting a printer Connecting a printer NOTE Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly. Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a printer.
Getting Started Connecting a printer 73 Setting up a printer NOTE Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure. If your printer does not support Plug and Play, follow these steps to set it up for the first time. You only need to set up the printer once. 1 Click Start, and then Printers and Faxes. The Printers and Faxes window appears. 2 Click Add a printer. The Add Printer Wizard appears.
Getting Started Connecting an optional external diskette drive Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5inch diskettes. (Sample Illustration) Optional external USB diskette drive To connect an optional external USB diskette drive, connect the cable to one of the computer’s USB ports. (Sample Illustration) Connecting an optional external USB diskette drive 5.375 x 8.375 ver 2.
Getting Started Turning off the computer 75 Turning off the computer Sliding the power switch before shutting down the Windows® operating system could cause you to lose your work. Make sure the system indicator panel’s disk light and the drive-inuse light are off. If you turn off the power while a disk/disc is being accessed, you may lose data or damage the disk/disc and/or drive. It is a good idea to turn off your computer when you are not using it for a while.
Getting Started Turning off the computer ❖ If you have work in progress and are not connected to a network, use the Windows® Standby or Hibernate commands to save your system settings so that, when you turn on the computer again, you will automatically return to where you left off. TECHNICAL NOTE: Before using any of these options to shut down or turn off your computer, save your files and make sure all disk/disc activity lights are off.
Getting Started Turning off the computer 77 For information on how to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 80. Standby mode The Standby command places the computer into a powersaving mode. Standby holds the current state of the computer in system memory (RAM) so that, when you restart the computer, you can continue working from where you left off.
Getting Started Turning off the computer Using the Turn Off Computer or Shut Down commands Depending on the operating system installed, use the following steps to turn off your computer. Turn Off For Windows® XP Home, or either Windows® XP Professional or Windows® XP MCE when not connected to a domain server, follow these steps to turn off the computer: 1 Click Start, and then Turn off computer. The Turn off computer dialog box appears.
Getting Started Turning off the computer 79 Turning off the computer more quickly You can also turn off the computer by sliding the power switch. To use this method, you first need to activate it using Toshiba’s Power Saver utility. 1 Click Start, Control Panel, and then Performance and Maintenance. 2 Click the TOSHIBA Power Saver icon. 3 Click on the Setup Action tab. (Sample Image) Setup action settings screen 4 Select the options you want from the drop-down lists.
Getting Started Turning off the computer 5 Click Apply. 6 Click OK. NOTE For more information about the Power Saver utility, see “TOSHIBA Power Saver” on page 178. Once the computer is configured, you can turn it off by either sliding the power switch or closing the display panel, depending on the options set. Restarting your computer To start the computer up again, slide the power switch until the on/off light glows green.
Getting Started Turning off the computer 81 Configuring Hibernation mode options You can place the computer into Hibernation mode by either sliding the power switch or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Hibernation mode. To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility. 1 Click Start, Control Panel, and then Performance and Maintenance. 2 Click the TOSHIBA Power Saver icon.
Getting Started Turning off the computer Starting again from Hibernation mode To start up the computer from Hibernation mode, slide the power switch until the on/off light glows green. The computer returns to the screen(s) you were using. If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.
Getting Started Turning off the computer 2 Click the TOSHIBA Power Saver icon. 3 Click the Setup Action tab. 4 Select Standby for the options you want. ❖ When I press the power button Set this option to Standby if you want the computer to go into Standby mode when you slide the power switch. ❖ When I close the lid Set this option to Standby if you want the computer to go into Standby mode when you close the display panel. 5 Click Apply. 6 Click OK.
Getting Started Using your computer in tablet mode Using your computer in tablet mode One of your computer’s features is a convertible display that allows you to use the screen much as you would a writing tablet. (Sample Illustration) Rotating the screen By simply rotating and folding the screen over the keyboard, your system is ready to use in tablet mode, with the included Toshiba tablet pen.
Getting Started Using your computer in tablet mode 85 (Sample Illustration) Using the computer in tablet mode To remove the tablet pen, press it in, and then pull it out from the right side of the computer. For more information on using the computer in tablet mode, see “Using tablet mode” on page 144. Your computer came with applications already installed specifically designed to work with the tablet feature of the system.
Getting Started Caring for your computer Caring for your computer This section gives tips on cleaning and moving your computer. For information about taking care of your computer’s battery, see “Taking care of your battery” on page 124. Cleaning the computer Keep liquids, including cleaning fluid, out of the computer’s keyboard, speaker, and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer.
Getting Started Caring for your computer 87 Using a computer lock You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com. (Sample Illustration) Computer lock cable To secure the computer: 1 Wrap the cable through or around some part of a heavy object. Make sure there is no way for a potential thief to slip the cable off the object.
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the disk. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved. See “Saving your work” on page 96 for further information.
Learning the Basics Computing tips ❖ 89 Back up your files to disks (or other removable media) on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your hard disk suddenly fails, you will lose all the data on it unless you have a separate backup copy. ❖ Use Error-checking and Disk Defragmenter regularly to conserve disk space and improve performance. ❖ Scan all new files for viruses.
Learning the Basics Using the keyboard Using the keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows® keys, providing all the functionality of a full-size keyboard. (Sample Illustration) Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The space bar creates a space character instead of just passing over an area of the page.
Learning the Basics Using the keyboard 91 Your computer’s keyboard has only one Enter and one Ctrl key. Most of the time, this does not matter. However, some programs assign separate functions to the right and left Ctrl and Alt keys, or to the regular and numeric pad Enter keys on the full-sized keyboard. Using the Fn key, you can simulate these separate keys, as follows: ❖ Press Fn and Ctrl simultaneously to simulate the Ctrl key on the right side of the enhanced keyboard.
Learning the Basics Using the keyboard Windows special keys Windows key Application key (Sample Illustration) Windows special keys Your computer’s keyboard has two keys that have special functions in Windows: ❖ Windows key—Opens the Start menu ❖ Application key—Has a similar function as the secondary mouse button Overlay keys The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay.
Learning the Basics Starting a program 93 Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys. To turn the numeric overlay on, press Fn and F11 simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on. To disable the numeric overlay, hold down the Fn key and press F11 again. The numeric mode light on the keyboard indicator panel goes out.
Learning the Basics Starting a program The next three sections explain how to start a program from the Start menu, Explorer and the Run dialog box. Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows® WordPad program as an example: 1 Click Start, and then All Programs.
Learning the Basics Starting a program 95 3 Click Windows Explorer. 4 Click My Computer to expand the window. 5 In the left part of the window, click the line that ends in “(C:).” 6 In the left part of the window, under the C: icon, doubleclick the folder containing the program, in this case Program Files. Windows® Explorer shows the contents of the Program Files folder on the right side of the window. The left side of the window shows all the folders contained within the Program Files folder.
Learning the Basics Saving your work 2 In the Run dialog box: ❖ If you know the program’s location, type the command line. For a program in the Windows® folder, type just the program name. Otherwise, type the full file path. For example, to access WordPad, type: c:\Program Files\Windows NT\Accessories\wordpad.exe, then click OK. HINT: To run the same program again, click the arrow to the right of the text box and select the command line from the drop-down list.
Learning the Basics Saving your work 97 Saving files 1 In your Windows® application, click File, and then Save. If you are working with a document that already has a file name, this is all you need to do. If you created a new document, your program displays a Save As dialog box. Use this dialog box to specify where to store the document and to give it a file name. (Sample Image) Save As dialog box 2 Choose the drive and folder where you want your file to be stored.
Learning the Basics Printing your work File names The Windows operating system supports long file names that can contain up to 255 characters and can include spaces. Some applications do not support long file names and require file names limited to no more than eight characters. You may use all the letters and numbers on the keyboard plus these characters: _ ^ $ ~ ! # % & { } ( ) @ and '. File names are not case-sensitive.
Learning the Basics Backing up your work 99 To print a file: 1 If your printer is not on, turn it on now. 2 In your Windows® application, click File, and then Print. The program displays a Print dialog box. (Sample Image) Print dialog box 3 Specify the print parameters. For example, the range of pages and number of copies to print. 4 Click Print. Backing up your work Back up all the files you create in case something happens to your computer.
Learning the Basics Using the optical drive HINT: Backing up all the files on your hard disk may take a considerable amount of time and multiple CDs/DVDs. You may prefer to use a high-capacity backup system, such as an external hard drive. Small files can be backed up on diskettes if an optional external diskette drive is available. Restoring your work To restore information from your backup media to your hard disk, use the Restore page in the backup program.
Learning the Basics Using the optical drive 101 TECHNICAL NOTE: Your optical drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region. The drive will allow you to change regions four times. On the fourth change, the region will be “locked in.” That is, the drive will only play DVDs from that last region.
Learning the Basics Using the optical drive Do not press the eject button or turn off the computer while the drive in-use indicator light is glowing. Doing so could damage the disc or the drive. When the disc tray is open, be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction. Manual eject hole—Use if you need to release the disc tray when the power is off.
Learning the Basics Using the optical drive 4 103 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty, clean it as described in “Caring for CD or DVD discs” on page 108. 6 Place the disc carefully in the disc tray, label side up. (Sample Illustration) Positioning the disc in the drive 5.375 x 8.375 ver 2.
7 Learning the Basics Using the optical drive Gently press the disc onto the center spindle until it clicks into place. Handle DVDs and CDs carefully, making contact only with the center hole and edge. Do not touch the surface of the disc. Do not stack discs. If you incorrectly handle the discs, you could lose data. 8 Make sure the disc is completely on the spindle and is lying flat on the tray. If you insert the disc incorrectly, it may jam the drive.
Learning the Basics Using the optical drive 105 Stop button Play/Pause button (Sample Image) Windows Media Player screen The Windows Media Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button. ❖ To stop the CD, click the Stop button. Before putting on headphones to listen to an audio CD, turn the volume dial down. Do not set the volume too high when using headphones. Continuous exposure to loud sound can harm your hearing.
Learning the Basics Using the optical drive If your disc does not run using this method, try using an application that is associated with the media on the disc. For example, if it is a music CD, open Windows® Media Player and use it to select and then play the CD. For other types of media, use the associated software to open the files on the disc.
Learning the Basics Using the optical drive 107 Removing a disc with the computer on To remove a disc (CD or DVD) with the computer turned on: 1 Press the eject button on the drive. Do not press the eject button while the in-use indicator light is glowing. Doing so could damage the disc or the drive. Also, if the disc is still spinning when you open the disc tray, wait for it to stop spinning before you remove it.
Learning the Basics Toshiba’s online resources Caring for CD or DVD discs ❖ Store your discs in their original containers to protect them from scratches and keep them clean. ❖ Do not bend a disc or place heavy objects on top of it. ❖ Do not apply a label to, or otherwise mar the surface of, a disc. ❖ Hold a disc by its outside edge. Fingerprints on the surface can prevent the optical drive from reading the data properly. ❖ Do not expose discs to direct sunlight or extreme heat or cold.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been set by Toshiba.
Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage.
Mobile Computing Running the computer on battery power 111 The RTC battery powers the RTC memory that stores your system configuration settings and the current time and date information. It maintains this information for up to a month while the computer is turned off. TECHNICAL NOTE: The RTC battery does not charge while the computer is turned off, even when AC power is attached. The RTC battery charges only while the computer is powered on.
Mobile Computing Charging batteries Charging batteries The battery needs to be charged before you can use it to power the computer. Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Always use the battery charger specified by Toshiba. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com.
Mobile Computing Charging batteries 113 The battery may not start charging immediately under the following conditions: ❖ The battery is extremely hot or cold. To ensure that the battery charges to its full capacity, wait until it reaches room temperature (50 to 80 degrees Fahrenheit, 10 to 26 degrees Celsius). ❖ The battery is almost completely discharged. Leave the power connected and the battery should begin charging after a few minutes.
Mobile Computing Monitoring main battery power If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working. To recharge the RTC battery, plug the computer into a live electrical outlet and leave the computer powered on for 24 hours. NOTE It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working.
Mobile Computing Monitoring main battery power NOTE 115 If the AC power light flashes amber during charging, either the battery pack is malfunctioning, or it is not receiving correct input from the AC power supply. Disconnect the AC power cord/cable and remove the battery pack. See “Changing the main battery” on page 121 for information on replacing the main battery. HINT: Be careful not to confuse the battery light ( ) and the on/off light ( ) (near the front-left edge of the keyboard).
Mobile Computing Monitoring main battery power Determining remaining battery power NOTE Wait at least 16 seconds after turning on the computer before trying to monitor the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform its calculations. 1 Click Start, Control Panel, Performance and Maintenance, and then TOSHIBA Power Saver. 2 Click the TOSHIBA Power Saver icon. The Power Saver Properties window appears.
Mobile Computing Monitoring main battery power 117 What to do when the main battery runs low When the main battery runs low you can: ❖ Plug the computer into an external power source and recharge the main battery ❖ Place the computer into Hibernation mode and replace the main battery with a charged spare ❖ Connect the computer to an optional high capacity battery (if available for your computer) ❖ Save your work and turn off the computer If you do not manage to do any of these things before the ma
Mobile Computing Monitoring main battery power Conserving battery power How long a fully charged battery pack lasts when you are using the computer depends on a number of factors, such as: ❖ How the computer is configured ❖ How much you use the hard disk, optical drive, diskette drives, or other optional devices ❖ Where you are working, since operating time decreases at low temperatures There are various ways in which you can conserve power and extend the operating time of your battery: ❖ Enabl
Mobile Computing Monitoring main battery power 119 Power Profiles You can choose a predefined Power Profile or select your own combination of power management options. To do this: 1 Click Start, Control Panel, Performance and Maintenance, and then TOSHIBA Power Saver. The TOSHIBA Power Saver Properties window appears. (Sample Image) TOSHIBA Power Saver Properties window 2 Select an appropriate profile for your work environment or create your own custom profile.
Mobile Computing Monitoring main battery power Using a hot key to set the Power Profile You may use a hot key to set the Power Profile. To set the Power Profile: 1 Press Fn and F2 simultaneously to display the Power Profile pop-up window. (Sample Image) Power Profile pop-up window 2 While continuing to press Fn, press F2 until you select the desired Power Profile. The Power Profile options are: Full Power, High Power, Normal, DVD Playback, Presentation, and Long Life. 3 Release the Fn key.
Mobile Computing Changing the main battery 121 Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or fire, and could also damage the battery pack and computer.
5 Mobile Computing Changing the main battery Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock 6 Slide the battery release latch to release the battery. 7 Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery 5.375 x 8.375 ver 2.3.
Mobile Computing Changing the main battery 123 If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately. Always dispose of used battery packs in compliance with all applicable laws and regulations. Put insulating tape, such as cellophane tape, on the electrode during transportation to avoid a possible short circuit, fire or electric shock. Failure to do so could possibly result in serious injury.
3 Mobile Computing Taking care of your battery Slide the battery lock to the locked position. (Sample Illustration) Locking the battery release lock 4 Turn the computer right side up. 5 Reconnect any cables that were removed in step 3 of “Removing the battery from the computer” on page 121. 6 Restart the computer. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life.
Mobile Computing Taking care of your battery 125 ❖ Do not overcharge or reverse charge a battery. Overcharging will shorten its life, and reverse charging could damage it. ❖ Avoid touching the metal terminals of the battery with another metal object. Short-circuiting the battery can cause it to overheat and may cause damage to the battery or the computer. ❖ Do not incinerate a spent battery, as this could cause it to explode and release caustic liquid.
Mobile Computing Taking care of your battery 3 Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the battery light flashes or there is some other warning to indicate a low battery, go to step 4. 4 Connect the AC adaptor to the computer and the power cord/cable to a power outlet.
Mobile Computing Disposing of used batteries 127 Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you have fully recharged the battery. You must discard a battery if it becomes damaged. Never attempt to dispose of a battery pack by burning or by throwing it into a fire, and never allow exposure to a heating apparatus (e.g., microwave oven).
Mobile Computing Traveling tips Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle, a program of the Rechargeable Battery Recycling Corporation. For more information and for drop-off locations, visit www.rbrc.org or call 1-800-8228837. Notice regarding CR coin cell batteries, applicable to California, U.S.A. only: Perchlorate Material - special handling may apply. See http://www.dtsc.ca.
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows® operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks. HINT: The illustrated examples in this guide may appear slightly different from the screens displayed by your system.
Exploring Your Computer’s Features Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, Taskbar, System tray, and background pattern. Icons Start button Taskbar System tray ® (Sample Image) Windows operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Exploring Your Computer’s Features Exploring the desktop 131 The icons initially displayed on your system desktop include: Recycle Bin — Holds files you have deleted. You may be able to retrieve these files until you empty the Recycle Bin. TECHNICAL NOTE: If you delete a file from a diskette or flash media, it does not go into the Recycle Bin. For more information on the Recycle Bin, see Windows online Help. Internet Explorer — The Microsoft® browser that provides access to the Internet.
Exploring Your Computer’s Features Setting up for communications Taskbar Each time you open a program, a button associated with that program appears on the Taskbar. With some programs, a button appears on the Taskbar for each document or window you open. You can use these buttons to quickly switch between the programs or windows. To make a program or window the currently active one, click the associated Taskbar button.
Exploring Your Computer’s Features Setting up for communications 133 Determining the COM port Your modem (available on certain models) is connected to one of the computer’s COM (communications) ports. The default setting for the modem is COM3. The following procedure is intended to support you if you need to either upgrade your modem or reset the port to the default settings. If you are having trouble connecting through the modem, you may need to determine the current COM port name and possibly change it.
Exploring Your Computer’s Features Setting up for communications 8 Click OK to close the properties dialog box for that specific modem. 9 Click OK to close the Modem Properties dialog box. 10 Close the Control Panel. Connecting the modem to a telephone line Your computer may come with a built-in modem (available on certain models) that can be connected to a standard voicegrade telephone line. The modem allows you to: ❖ Access the Internet.
Exploring Your Computer’s Features Setting up for communications 135 (Sample Illustration) Connecting the telephone cable to the modem port 2 Connect the other end to the RJ-11 wall jack. (Sample Illustration) Connecting to a wall jack NOTE Connect the built-in modem only to ordinary analog phone lines. Never connect the built-in modem to a digital line (ISDN). Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).
Exploring Your Computer’s Features Setting up for communications Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality using one of its communication ports. Accessing a network To access a network: ❖ At the office, connect an Ethernet cable to the RJ45 jack on your computer. For specific information about connecting to the network, consult your network administrator.
Exploring Your Computer’s Features Setting up for communications 137 How to disable the Ethernet LAN port When your computer starts, Windows attempts to contact a Dynamic Host Configuration Protocol (DHCP) server. If the computer is not connected to a network, it may pause a few minutes as it waits for a reply. To avoid this delay, you can reconfigure Windows to disable the LAN port. To disable the LAN port: 1 Click Start, Control Panel, and then Performance and Maintenance.
Exploring Your Computer’s Features An overview of using the Internet Your system may come with an optional wireless LAN module. This is a technology that expands wireless communication beyond networking equipment, and can connect many different kinds of electronic devices without the need for cables. For information on how to set up a wireless connection, refer to your wireless networking device documentation or your network administrator.
Exploring Your Computer’s Features An overview of using the Internet 139 The Internet The Internet is an association of thousands of networks and millions of computers around the world connected by communications lines. They all work together to share information.
❖ Exploring Your Computer’s Features An overview of using the Internet An Internet Service Provider (ISP) account The Microsoft® Web browser Internet Explorer is automatically configured on your system so that when you first start it, it guides you through signing up for a new ISP account, or assists you in setting up your computer to work with your existing ISP. Once you have established an ISP account, you can connect to the Internet. 1 Connect your computer’s modem to a telephone line.
Exploring Your Computer’s Features An overview of using the Internet 141 Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive email of your own, you need a mailbox on the Web or an email address. If you have an account with an ISP, you can probably set up an email address at the same time you sign up for the service.
Exploring Your Computer’s Features Exploring audio features There are several ways to upload or download data. It can be as simple as attaching a file or document to an email, or you can use the File Transfer Protocol (FTP) features of your Web browser to transfer large amounts of data. Exploring audio features You can use your computer to record sounds using an external microphone. You can play sound files or audio CDs using the built-in speakers, headphones, or external speakers.
Exploring Your Computer’s Features Exploring audio features 5 143 When you have finished recording, click the Stop button. The Sound Recorder window displays the new sound file as a waveform. NOTE You can only record 60 seconds at a time. 6 To hear what you just recorded, click the Play button. 7 To save the file, select Save from the File menu. NOTE The microphone on your computer might be set to Mute. To check this, click Start, All Programs, Accessories, Entertainment, and then Volume Control.
Exploring Your Computer’s Features Using tablet mode To play back sound files through external speakers or headphones: 1 Locate the headphone jack on the computer. 2 Using any necessary adapters, plug the cable from the headphones or external speakers into the headphone jack. The headphone jack requires a 16-ohm stereo mini-jack. To adjust the volume: ❖ For external speakers, use the volume controls on each speaker. ❖ For headphones, use the computer’s volume control dial.
Exploring Your Computer’s Features Using tablet mode 3 145 Rotate the display panel clockwise 180o (degrees). When you complete this task, the screen faces away from the keyboard. When rotating LCD screen of your computer, be sure to slowly turn the screen in the proper direction, and not apply excessive force or speed. (Sample Illustration) Rotating the display panel clockwise 180o 4 Turn the display latch so it points toward the back of the LCD screen. 5.375 x 8.375 ver 2.
5 Exploring Your Computer’s Features Using tablet mode Fold the display panel down flat over the keyboard. The display latch will click and lock the screen in tablet position. Display latch (Sample Illustration) Folding the display panel down flat By default, the computer desktop will automatically rotate to primary portrait view. For more information on changing tablet screen settings, see “TOSHIBA Rotation Utility” on page 184.
Exploring Your Computer’s Features Using tablet mode 147 Using tablet mode 1 Remove the Toshiba tablet pen which is located on the right side of the computer by momentarily pressing in on the pen and then releasing it. Pull the pen from the holder. (Sample Illustration) Removing the Toshiba tablet pen from the slot on the tablet computer NOTE To protect the computer’s display, make sure you change from tablet mode to computer mode and close the display before you turn the computer upside down.
2 Exploring Your Computer’s Features Using tablet mode Use the Toshiba tablet pen on the tablet as you would any pointing device or pen. (Sample Illustration) Writing on the tablet To learn how to manually change the layout of the screen from portrait to landscape, see “TOSHIBA Rotation Utility” on page 184. NOTE You can also use tablet mode when the computer is in its original configuration, with the screen open and facing the keyboard.
Exploring Your Computer’s Features Using PC Cards ❖ 149 To drag a window to another location on the tablet, press the Toshiba tablet pen on the window's Title Bar, and then hold it while you drag it to its new location. When working in an application, you can use the Toshiba tablet pen like a pen and simply draw or write directly onto the tablet’s work space.
Exploring Your Computer’s Features Using PC Cards Inserting a PC Card Before you insert a PC Card, refer to the documentation that comes with the card to see if you need to do anything before you insert it. To insert a PC Card: 1 Locate the PC Card slot on the left side of the computer. 2 Insert the PC Card. PC Card slot (Sample Illustration) Inserting a PC Card 3 When the card is almost all the way into the slot, push firmly but gently to ensure a firm connection with the computer.
