TOSHIBA Storage Device Division DVD-RAM DRIVE SD-W2002 Installation Instructions with VOB InstantWrite and CyberLink PowerDVD Software TM VERSION 3.
Limited Warranty Toshiba America Information Systems, Inc. Storage Device Division 9740 Irvine Boulevard, Irvine, California 92618 1-949-457-0777 What does my limited warranty cover? Toshiba America Information Systems, Inc. (“Toshiba”) warrants the Toshiba Storage Product (“Product”) you have purchased from Toshiba or from a Toshiba authorized dealer is free from defects in materials or workmanship under normal use during the warranty period.
Disclaimer and limitation of remedy ALL OTHER EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND/OR NONINFRINGEMENT OF THIRD PARTY RIGHTS, ARE HEREBY DISCLAIMED. TOSHIBA EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE TERM OF THIS EXPRESS LIMITED WARRANTY.
Table of Contents Kit Packaging .............................................................................................. 1 System Requirements .................................................................................. 1 Setting Jumpers ........................................................................................... 2 Connecting Cables ....................................................................................... 3 Completing Installation ....................................
Congratulations on your purchase of a Toshiba DVD-RAM drive and Kit. The following information will help you in the simple installation of your new DVDRAM drive.
The following steps must be performed to properly install your DVD-RAM. ● Set drive’s jumpers ● Connect audio cable ● Attach IDE BUS cable ● Connect power cable ● Mount DVD-RAM ● Install CyberLink PowerDVD™ software (used for viewing DVD movies) ● Install VOB InstantWritesoftware (used for recording CDs) SETTING JUMPERS The mode select jumpers are six (6) straight angle pins located on the rear of the DVD-RAM.
1. Remove computer cover and faceplate if required (refer to your computer system’s manual for removal information). 2. If the DVD-RAM is replacing a CD-ROM, disconnect all connectors and remove the CD-ROM presently installed in your system. 3. Your Toshiba DVD-RAM can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.) 4. Carefully start sliding the DVD-RAM into the opening with the disc tray facing the front of the computer.
cable (side with red stripe) is connected to pin 1 on the drive. • If the DVD-RAM is the only drive connected on the secondary IDE BUS cable: connect drive to the last set of pins on IDE BUS cable. • If there is a device (i.e. CD-ROM) connected to the secondary IDE BUS cable: connect DVD-RAM to the open middle connector . The DVD-RAM drive should then be jumpered to SL (slave) position.
COMPLETING INSTALLATION After you have connected all the necessary cables, push the DVD-RAM completely into the computer’s drive slot. Mount the drive per your computer’s instructions using the screws included in your kit. If you are using other screws, assure that the screw length does not exceed 3±0.5mm (measured from outside surface of side or bottom of DVD-RAM to tip of screw). Replace the computer cover and all outer screws.
DVD-RAM FRONT PANEL The photo below illustrates the following features of the SD-W2002 DVD-RAM’s front panel: Emergency Eject Hole: The emergency eject hole is to be used only when the DVD tray will not open when the Load/Unload button is pressed. Insert solid bar (i.e. paper clip) into hole, applying gentle presure, until tray opens. Do not use Emergency Eject Procedure while the drive is in operation.
OPERATING THE DVD LOADING TRAY To open the DVD loading tray, just press the Load/Unload button. After inserting or removing a disc or recording cartridge, press the Load/Unload button again. You must use a DVD-RAM recording cartridge when recording DVD-RAM media. Vertical Disc Installations When placing a disc into a DVD-RAM drive that has been mounted vertically, be assured that the disc in installed under the two front tabs.
SPECIFICATIONS DVD CD DATA CAPACITY 2,048bytes/block mode 1: 2,048bytes/block mode 2: 2,336bytes/block ROTATIONAL SPEED (RPM) DVD-RAM (2.0): 1,380 - 3,300 2,100 - 3,300 DVD-RAM (1.0): 1,080 - 2,400 DVD-ROM (single): 2,400 DVD-ROM (double): 3,800 DVD-R,DVD-RW: 1,100 - 2,800 CD-ROM, CD-R: 5,100 CD-RW: 3,400 Video CD: 900 - 2,000 CD-DA: 1,800 - 4,200 SUSTAINED DATA TRANSFER RATE (kbytes/sec) DVD-RAM(2.1) 2,704 DVD-RAM (1.
9
460020-C0 P/N 460020-C0
