MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS Quick Start Guide
Lineup of Our Manuals Some of these manuals are printouts and others are PDF files recorded in the Client Utilities/User Documentation DVD. In the printouts, precautions and basic operations are described. Be sure to read “Safety Information” before using the equipment. In the PDF files, detailed copying functions and other settings are described. Select and read those best suited to your needs. Printouts Safety Information This Safety Information describes the necessary precautions for use.
PDF files Copying Guide This Copying Guide describes the operations and settings enabled with the [COPY] button on the control panel. Scanning Guide This Scanning Guide describes the operations and settings enabled with the [SCAN] button on the control panel and those of Internet Fax. e-Filing Guide This e-Filing Guide describes the operations and settings enabled with the [e-FILING] button on the control panel and the e-Filing web utility.
How to Read This Manual Symbols in this manual In this manual, some important items are described with the symbols shown below. Be sure to read these items before using this equipment. Indicates a potentially hazardous situation which, if not avoided, could result in death, serious injury, or serious damage, or fire in the equipment or surrounding objects.
CONTENTS How to Read This Manual ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2 Recommended toner cartridges ����������������������������������������������������������������������������������������������������������������������������������������������������������������������� 4 Chapter 1 PREPARATIONS Description of Each Component ������������������������������������������
Recommended toner cartridges To assure optimal printing performance, we recommend that you use only genuine TOSHIBA toner cartridges. If you use a TOSHIBA-recommended toner cartridge, you can utilize the following three functions of this equipment: • Cartridge detecting function: This function checks if the toner cartridge is correctly installed and notifies you if it is not.
Chapter 1 PREPARATIONS Description of Each Component ��������������������������������������������������� 6 Turning Power ON/OFF ������������������������������������������������������������������� 12 Placing Paper and Originals ��������������������������������������������������������� 15 Installing Client Software ��������������������������������������������������������������� 17
Chapter 1 PREPARATIONS Description of Each Component This section describes the names and operations of the equipment, control panel and touch panel. Front / Right side 18 17 1 Back side 2 5 16 6 15 7 14 13 12 8 9 Reversing Automatic Document Feeder The stack of originals is scanned one sheet at a time. Both sides of the originals can be scanned. A maximum of 100 sheets (80 g/m2 or 20 lb. Bond) can be placed in one go.
Description of Each Component 15. Front cover 17. Alarm lamp Open this cover when you replace the toner cartridge and clean the charger. 16. Main power switch This orange lamp lights when a paper misfeed has occurred in the Reversing Automatic Document Feeder. 18. Document lamp Use this switch to turn the power of the equipment ON or OFF. & P.12 “Turning Power ON/OFF” in this manual This blue lamp lights when the originals are placed on the original feeder tray.
Chapter 1 PREPARATIONS Control panel Use the buttons on the control panel for various operations and settings in the equipment. 1 2 4 3 5 6 7 8 9 10 11 12 22 1. 21 20 [SCAN] button Use this button to access the scanning function. 2. [COPY] button Use this button to access the copying function. 3. [MENU] button Use this button to display frequently used templates. 4.
Description of Each Component 19. [FAX] button Use this button to access the Fax / Internet Fax function. 20. [e-FILING] button Use this button to access stored image data. This button is not provided for the e-STUDIO2051C/ 2551C. 21. [PRINT] button Use this button to access the printing functions such as private printing, in this equipment. 22. Touch panel Use this panel for the various settings of the copying, scanning and Fax functions.
Chapter 1 PREPARATIONS Touch panel When the power is turned ON, the basic menu for copying functions is displayed on this touch panel. The status of the equipment is also displayed on the touch panel with messages and illustrations. The menu shown at the time of turning the power ON can be changed to one for functions other than copying, for example, Fax function. Contact your service technician or representative for details. 1 2 6 5 4 1.
Description of Each Component Setting letters The following menu is displayed when the entry of any letter is required for scanning or e-Filing, etc. Use the buttons on the touch panel for letter entry. After entering the letters, press [OK]. The menu will be changed. 1 The following buttons are used for letter entry. [Basic]: Press this to access the basic keys. [Symbol]: Press this to access the symbol keys. [Other]: Press this to access the special keys.
Chapter 1 PREPARATIONS Turning Power ON/OFF This section explains how to turn the power ON and OFF as well as the energy saving mode. How to turn the power ON differs between when the MAIN POWER lamp (green) on the control panel is lit and when it is not. Turning the power ON When the MAIN POWER lamp (green) on the control panel does not light: Turn the power ON there. When the MAIN POWER lamp (green) on the control panel lights: • The equipment starts warming-up.
Turning Power ON/OFF Turning the power OFF (Shutdown) When turning the power of the equipment OFF, be sure to shut it down according to the procedure below. Check the following three points before shutdown. • No jobs should be left in the print job list. • None of the PRINT DATA lamp (blue) or the MEMORY RX / LINE lamp (green) should be blinking. (If the equipment is shut down while any of the above lamps is blinking, jobs in progress such as FAX reception will be aborted.
Chapter 1 PREPARATIONS Saving energy when not in use – energy saving modes – This equipment supports three energy saving modes; the Automatic Energy Save mode, Sleep mode and Super Sleep mode. The table below shows the procedures to switch modes manually and the conditions under which the equipment enters into or recovers from each mode.
Placing Paper and Originals Placing Paper and Originals This section explains how to set paper and originals. Incorrect setting causes image skews or paper misfeeds. Follow the procedure below. Placing paper 1 1 4 1 2 2 1 Pull out the drawer, and press down the paper plate. When placing paper in the Paper Feed Unit, Paper Feed Pedestal, or Additional Drawer Module, pull out the drawer, and then proceed to step 2. Set the side guides so that they match the paper size. 5 2 Push in the drawer.
Chapter 1 PREPARATIONS Placing originals Original glass Reversing Automatic Document Feeder 1 1 Raise the Original Cover or the Reversing Automatic Document Feeder. Place the originals face up on the original feeder tray. Be sure that the document lamp (blue) lights up, which is provided on the Reversing Automatic Document Feeder. 2 2 Place the original with its face down on the original glass and align it against the left rear corner. Align the side guides to the original length.
Installing Client Software Installing Client Software How to install the client software such as the printer driver from the Client Utilities/User Documentation DVD co-packed with the equipment is described as follows. Recommended installation The recommended client software such as the printer driver can be installed all in one go. 1 2 1 Turn the power ON and confirm that “READY” appears on the touch panel. & P.
Chapter 1 PREPARATIONS 7 When the installation is completed, click [Finish]. • For details of the Client Utilities/User Documentation DVD, see the following page. & P.61 “Client Utilities/User Documentation DVD“ in this manual • For details of the recommended installation, refer to the following guide. & Software Installation Guide (PDF): “Chapter 2: RECOMMENDED INSTALLATION” 8 Click [Exit] and then [Yes] to finish the installation.
Chapter 2 BASIC OPERATION Basic Copying Operation ��������������������������������������������������������������� 20 Basic Fax Operation ������������������������������������������������������������������������� 24 Basic Scanning Operation ������������������������������������������������������������� 28 Basic e-Filing Operation ����������������������������������������������������������������� 30 Basic Printing Operation ��������������������������������������������������������������� 32 Basic Menu Operati
Chapter 2 BASIC OPERATION Basic Copying Operation The basic copying procedures, such as enlargement/reduction copying and duplex copying as well as bypass copying, are as follows. Making copies 1 Press the [COPY] button on the control panel. 2 Place the original(s). 3 Select the copy modes as required. & P.16 “Placing originals” in this manual You can switch the color mode. There are 3 color modes as shown below. FULL COLOR: All originals are copied in full color.
Basic Copying Operation Enlargement and reduction copying 1 Press [ZOOM]. 2 1 Select the desired paper size, 2 press [AMS], and then 3 [OK]. 2 Selecting finishing mode (sorting) 1 1 Press [FINISHING]. When you use the Reversing Automatic Document Feeder, the sorting mode is automatically set. 2 2 1 Press [SORT] and then 2 [OK]. 1 3 2 • Align the originals according to the desired paper size and direction. The size of the originals will be automatically determined.
Chapter 2 BASIC OPERATION Setting duplex copy Setting original mode 1 Press [2-SIDED]. 1 Press [ORIGINAL MODE]. 2 1 Select the desired duplex mode and then 2 press [OK]. 2 1 Select the desired original mode and then 2 press [OK]. 1 1 2 2 e-STUDIO2051C/2551C: This mode is available only when the Automatic Duplex Unit is installed. You can choose from 5 types. For example, the following settings can be made.
Basic Copying Operation Density adjustment You can manually adjust the density by pressing either or . Bypass copying 1 1 Move the paper holding lever toward the outside and then 2 place paper face down on the bypass tray. 1 2 2 To lighten the density, press , to darken it, press . Align the side guides to the paper length and then move the paper holding lever toward the equipment. 2 Press [AUTO] to adjust the density automatically.
Chapter 2 BASIC OPERATION Basic Fax Operation The basic procedures for sending a fax, such as specifying fax numbers in the address book or setting the transmission conditions, are as follows. Sending a fax 1 Press the [FAX] button on the control panel. 2 Place the original(s). 3 Key in the fax number of the recipient by pressing [INPUT FAX No.] on the touch panel or the digital keys on the control panel. & P.
Basic Fax Operation Specifying recipients in the address book Specifying recipients one by one Confirming recipients 1 Press [DESTINATION]. 2 The recipient list screen is displayed. 1 Press the [SINGLE] tab to display the list of addresses, and then 2 the recipient’s fax icon. 1 2 2 Specifying recipients in groups 1 Press [GROUP] tab to display the list of the groups, and then 2 the group name. 2 Select the recipient you want to delete, and then press [DELETE].
Chapter 2 BASIC OPERATION Setting the transmission conditions Canceling reserved transmissions 1 Press [OPTION]. 1 2 The transmission condition setting screen is displayed. Press or to switch the pages. 2 Press [JOB STATUS]. 1 Press [FAX], 2 select the reserved transmission you want to delete, and then 3 press [DELETE]. 1 3 3 RESOLUTION: Set the resolution based on the fineness of the original. ORIGINAL SIZE: Set the scan size of the original. 3 26 After each item is set, press [OK].
Basic Fax Operation Checking communication status (log) 1 2 Press [JOB STATUS]. Registering recipients 1 Press the [USER FUNCTIONS] button on the control panel and then [ADDRESS] on the touch panel. 1 Select the [LOG] tab and then 2 press [SEND]. 2 1 Press an open button to create a new recipient and then 2 [ENTRY]. 2 2 1 1 2 Press [RECEIVE] to check the fax reception log. 3 The communication status list is displayed. If [OK] is indicated in the “Status”, the transmission succeeded.
Chapter 2 BASIC OPERATION Basic Scanning Operation The basic operation of the scanning function, how to store the scanned data in a shared folder and store these data in a Windows computer is described as follows. Storing the scanned data in a shared folder This operation is available only when the hard disk is installed in the equipment. 1 Press the [SCAN] button on the control panel. 4 1 Set [FILE NAME], 2 FILE FORMAT, etc. and then 3 press [OK]. 2 1 28 2 Place the original(s). & P.
Basic Scanning Operation To store the scanned data of a shared folder in a Windows computer This operation is available only when the hard disk is installed in the equipment. 1 Start up Windows Explorer. 2 Enter the name of the shared folder, in which the IP address of the equipment and the scanned data are stored, in the address bar with the following format, and then press the [Enter] button. Format: \\[IP address of the equipment] \file_share e.g.) When the IP address of the equipment is 172.16.16.
Chapter 2 BASIC OPERATION Basic e-Filing Operation e-Filing is a function to store documents in the hard disk of the equipment, they can then be printed as required. Storing documents The originals are stored as e-Filing documents in the equipment. This operation is available only when the hard disk is installed in the equipment. 1 Press the [COPY] button on the control panel. 4 1 Specify the box to be stored and the document name, and then 2 press [OK]. 1 2 2 Place the original(s). & P.
Basic e-Filing Operation Printing Documents The procedure for printing documents stored in e-Filing is as follows. This operation is available only when the hard disk is installed in the equipment. 1 Press the [e-FILING] button on the control panel. 2 2 3 Select the box on the touch panel that contains the document you want to print. 1 Select the document you want to print, and then 2 press [PRINT]. Printing starts. 1 2 Selected documents can be previewed in thumbnailed form.
Chapter 2 BASIC OPERATION Basic Printing Operation The basic operation of the printer function is as follows. This is for printing from a Windows computer with a Universal Printer 2 driver which needs to be installed in advance. 1 2 Select [Print] in the [File] menu of the application. 1 Select the printer driver of the equipment, and then 2 click [Preferences] ([Properties]). 1 2 3 Set the print options as required and click [OK]. 4 Click [Print] ([OK]). Printing starts.
Basic Printing Operation Setting Universal Printer 2 driver 2 To specify paper size or number of copy sets Click the [Basic] tab in the property dialog box of the printer driver. To specify 2-sided printing or N-up printing Click the [Finishing] tab in the property dialog box of the printer driver. If the Finisher is installed, “Staple” or “Hole Punch” can be selected. 2IN1 4IN1 Select “Number of pages per Sheet” to print several pages on one sheet.
Chapter 2 BASIC OPERATION Basic Menu Operation Press the [MENU] button on the control panel to use templates and check the print counter. When the user management function is enabled, log in and press the [MENU] button on the control panel. The menu screen for a logged in user is displayed. You can register frequently used templates, a group of templates or the shortcut of the External Interface Enabler. Registration or deletion of the shortcut can also be enabled in the TopAccess mode.
Chapter 3 MAINTENANCE Replacing Toner Cartridge ������������������������������������������������������������� 36 Replacing Waste Toner Box ����������������������������������������������������������� 37 Replacing Staple Cartridge ����������������������������������������������������������� 38 Regular Cleaning ������������������������������������������������������������������������������� 42
Chapter 3 MAINTENANCE Replacing Toner Cartridge When “Install new *** toner cartridge” appears on the touch panel, replace the toner cartridge according to the following procedures. 1 4 Open the front cover. Pull the seal straight out in the direction of the arrow. 2 5 Remove the color toner cartridge you want to replace. Insert the new toner cartridge straight along the guide until it stops. 3 6 10 Shake the new toner cartridge well to loosen the toner inside.
Replacing Waste Toner Box Replacing Waste Toner Box When “Dispose of used toner” appears on the touch panel, replace the waste toner box according to the following procedures. 1 1 1 4 Y M C K 2 Open the front cover, and put your fingers in the waste toner box front grooves, then take it out toward you pushing down the top latch. 2 Insert the cleaner through the service hole of the developer to the end. 5 3 Pull down the 4 green levers located under the toner cartridges.
Chapter 3 MAINTENANCE Replacing Staple Cartridge When “Check staple cartridge” appears on the touch panel, replace the staple cartridge according to the following procedures. Stapler Unit of Saddle Stitch Finisher 38 1 4 Open the front cover of the Finisher. Install a new staple case into the staple cartridge. 5 Take off the staple cartridge. Install the staple cartridge. 6 Take the empty staple case out of the staple cartridge. Close the front cover of the Finisher.
Replacing Staple Cartridge Saddle Stitch Unit of Saddle Stitch Finisher 1 4 Open the left cover of the Finisher. Install new staple cartridge. 2 5 3 Take off the staple cartridge. Close the left cover of the Finisher. 3 Pull out straight the seal bundling the staples.
Chapter 3 MAINTENANCE Stapler Unit of Inner Finisher 1 4 1 2 Lift up the control panel, and open the front cover of the Finisher. Take off the staple cartridge. 2 5 1 2 Holding the lever, move the finisher to the left until it comes to a stop. Push the buttons of both side of the cartridge to take off the staple case. 3 6 1 2 Open the Hole Punch Unit while pushing the lever. 40 Install a new staple case.
Replacing Staple Cartridge 7 9 Install the staple cartridge. Carefully return the finisher to its original position. 8 10 3 Return the Hole Punch Unit to its original position. Close the front cover of the Finisher. Do not put your hand or fingers on the top of the finisher when closing it. They could be caught and this could injure you.
Chapter 3 MAINTENANCE Regular Cleaning Regular Cleaning Poor quality printing such as uneven and soiled images can be improved by simple cleaning. This section describes the cleaning methods for the equipment. Cleaning for the scanning area, original glass, guide and platen sheet We recommend you to clean the following items weekly, so that the originals can be scanned in unsoiled conditions. Be careful not to scratch the parts that you are cleaning. • Be careful not to scratch the portions in cleaning.
Regular Cleaning Cleaning the main chargers and LED print heads If the inside of the main chargers and the print heads of the LED are dirty, the dirt will be transferred to the copied image. Clean them following the procedure below. 1 3 1 1 2 Open the front cover. Put your fingers in the waste toner box front grooves and take it out toward you pushing down the top latch, and then clean the LED print heads. For instructions on how to clean the LED print heads, see the following: & P.
44
Chapter 4 TROUBLESHOOTING Troubleshooting ������������������������������������������������������������������������������� 46
Chapter 4 TROUBLESHOOTING Troubleshooting When problems such as paper misfeeds occur, see the following explanation or refer to the Troubleshooting Guide (PDF) according to & P.48 “References to the Troubleshooting Guide” in this manual. Symbols and messages appear on the touch panel Symbols or messages of such as for paper misfeeds occasionally appear on the touch panel.
Troubleshooting Covers of the Finisher, the Hole Punch Unit and the Bridge Unit The covers of the Finisher, Hole Punch Unit and Bridge Unit to be opened when paper misfeeds occur are as indicated by the arrows in the following illustrations. The Saddle Stitch Finisher, the Hole Punch Unit and the Bridge Unit The Inner Finisher and the Hole Punch Unit 4 Using the Help functions If you press on the upper right of the touch panel, explanations of the functions and buttons on the screen are displayed.
Chapter 4 TROUBLESHOOTING About Troubleshooting Guide The Troubleshooting Guide (PDF) describes the causes and the troubleshooting of problems when you use the equipment.
Chapter 5 ADVANCED FUNCTIONS Advanced Functions ����������������������������������������������������������������������� 50
Chapter 5 ADVANCED FUNCTIONS Advanced Functions In Chapter 2 in this manual, the basic functions are described. This section describes the advanced functions to help you get the best out of your equipment. Examples of the advanced functions describing in this section Copying different-sized originals and stapling copies (LT) (LD) Attaching the scanned data to an E-mail (LT) (LD) & P.51 in this manual & P.
Advanced Functions COPY FAX SCAN e-FILING PRINT Copying different-sized originals and stapling copies (LT) 1 (LT) (LD) (LD) Place the originals on the Reversing Automatic Document Feeder. 5 & P.16 “Placing originals” in this manual The procedure of how to copy 5 sets of different-sized originals (A4 or LT: 1 sheet, A3 or LD: 4 sheets) and staple the copies is as follows. The Reversing Automatic Document Feeder and the Finisher are required.
Chapter 5 ADVANCED FUNCTIONS COPY SCAN FAX e-FILING PRINT Copying or scanning originals without blank sheets You can copy or scan originals omitting blank sheets while maintaining the original page sequence. 1 5 3 1 3 6 5 6 When copying 1 Place the originals on the Reversing Automatic Document Feeder. When scanning 1 & P.16 “Placing originals” in this manual 2 3 Press the [EDIT] tab, and then in the basic menu for the copying functions. Press [OMIT BLANK PAGE] and then [OK].
Advanced Functions COPY FAX SCAN e-FILING PRINT Storing data in a shared folder as well as sending a fax You can store documents in a shared folder in the equipment or in a computer connected to the network as well as sending a fax. This operation is available only when the hard disk is installed in the equipment. 1 Place the original(s). 2 Press [STORAGE] on the touch panel. 3 & P.
Chapter 5 ADVANCED FUNCTIONS COPY FAX SCAN e-FILING PRINT Registering frequently used scan settings in templates If you register frequently used scan settings in templates, you can easily perform scan operations only by recalling the templates. How to register scan settings (scan data are stored in PDF format in a shared folder) in templates (PUBLIC TEMPLATE GROUP) is described here. 1 2 Press [FILE] on the touch panel. 6 1 Select “PDF” in the file format, and then 2 press [OK].
Advanced Functions COPY FAX SCAN e-FILING PRINT Attaching the scanned data to an E-mail The procedure for attaching the scanned data to an E-mail and sending it to the specified E-mail address is as follows. 1 Place the original(s). 2 Press [E-MAIL] and then [TO] on the touch panel. 3 1 Specify the E-mail address and then 2 press [OK]. & P.16 “Placing originals” in this manual 1 2 4 Define the settings for the file as required and then press [OK]. 5 Press [SCAN] on the touch panel.
Chapter 5 ADVANCED FUNCTIONS COPY FAX SCAN e-FILING PRINT Adding date and time to document files The procedure for printing a document file stored in e-Filing with the date and time added at the bottom is as follows. YYYY . MM . DD 11:11 This operation is available only when the hard disk is installed in the equipment. 1 Select the box in which the desired document is stored. 2 1 Select the document and then 2 press [SETTINGS]. 1 2 3 Press [TIME STAMP]. 4 1 Press [LOWER] and then 2 [OK].
Advanced Functions COPY FAX SCAN e-FILING PRINT Printing a PDF file stored in the USB device The procedure for printing 1 set of a PDF file stored in the USB device is as follows. This operation is available only when the Front USB Cable is mounted in e-STUDIO2050C/2550C. 1 Connect the USB device to the USB port. 2 Press the [PRINT] button on the control panel. 3 Click the pull-down menu, and then select [USB]. 4 1 Select a PDF file to be printed and then 2 press [PRINT]. Printing starts.
Chapter 5 ADVANCED FUNCTIONS COPY FAX SCAN e-FILING PRINT Printing only allowed data set on the control panel The procedure for printing only allowed data set on the control panel is as follows. This will stop you from forgetting to remove printed sheets. 1 This operation is available only when the hard disk is installed in the equipment. 1 2 3 Open a file to be printed on a Windows computer, and then select [Print] from the file menu of the application.
Chapter 6 INFORMATION ABOUT EQUIPMENT Items Included in This Product ����������������������������������������������������� 60 Client Utilities/User Documentation DVD ������������������������������� 61 Client Software ��������������������������������������������������������������������������������� 62 Options ������������������������������������������������������������������������������������������������� 64 Logging in ��������������������������������������������������������������������������������������
Chapter 6 INFORMATION ABOUT EQUIPMENT Items Included in This Product The following items are co-packed with the equipment. Check that you have them all. Contact your service technician or representative if any are missing or damaged. Items included in this product Safety Information The Safety Information describes the necessary precautions for use. For your added security, be sure to read this booklet first.
Client Utilities/User Documentation DVD Client Utilities/User Documentation DVD The Client Utilities/User Documentation DVD contains pdf files of the Operator’s Manuals and the following client software such as the printer drivers and the utility software.
Chapter 6 INFORMATION ABOUT EQUIPMENT Client Software This section describes the outlines of the client software of the equipment. It is necessary to install software except e-Filing Web utility and TopAccess in the computer before it is used. Client software for the printing functions Universal Printer 2 driver This Universal Printer 2 driver is installed with the Recommended Installation. This driver is generally used.
Client Software Client software for the e-Filing functions TWAIN driver File downloader e-Filing Web utility e-Filing Backup/Restore Utility This driver enables you to obtain documents stored in e-Filing as an image in application supporting TWAIN on Windows computers.
Chapter 6 INFORMATION ABOUT EQUIPMENT Options The following options are sold separately, and upgrade the performance of the equipment if installed. For details, contact your service technician or representative. e-STUDIO2050C/2550C , e-STUDIO2051C/2551C 1 2 e-STUDIO2050C/2550C e-STUDIO2051C/2551C 10 11 3 12 13 5 6 1. Original Cover (KA-1640PC) 7 8. This is used to hold an original. .
Options Other options available are as follows. Contact your service technician or representative for details. Work Table (KK-4550) This is a small table for placing originals while the equipment is being operated. Installed on the right-hand side of the equipment. FAX Unit (GD-1320) This is a unit for using the equipment as a Fax machine. Installed in the rear side of the equipment. 2nd Line for FAX Unit (GD-1260) This unit enables you to add a line to the Fax, making a 2nd line available.
Chapter 6 INFORMATION ABOUT EQUIPMENT How to use the Accessible Arm A person in a wheelchair can close the Reversing Automatic Document Feeder using the Accessible Arm. Store it near the equipment. 1 Hold the Accessible Arm. 2 1 2 Hook the Accessible Arm on the right-hand side of the Reversing Automatic Document Feeder to close it. Do not store the Accessible Arm by attaching it on the equipment.
Logging in Logging in When the equipment is controlled under department or user management, copying and other functions can be performed if you log in according to the following procedure. Department management You can restrict users or manage copy volumes made by an individual group or department in your company using the department codes. When the equipment is controlled under the department code, turn the power on and enter the code.
Chapter 6 INFORMATION ABOUT EQUIPMENT User management You can restrict users or manage available functions and past records by means of user management. When the equipment is managed under this function, turn the power ON and enter the information required (e.g. user name, password). The menu for entering user information also appears when you press the [ACCESS] button on the control panel or automatic function clear has worked. Enter the information according to the procedure below.
Logging in 1 The menu for user authentication appears. 4 Press [PASSWORD]. MFP local authentication Windows Domain authentication, LDAP authentication The domain name previously set by the network administrator is displayed in [DOMAIN]. For LDAP authentication, the LDAP server name is displayed in [LDAP] instead of [DOMAIN]. 5 6 Enter the password (maximum 64 letters) and then press [OK]. Press [OK].
Chapter 6 INFORMATION ABOUT EQUIPMENT Specifications of Equipment This section describes the types of acceptable paper, sheet capacity of each feeder and the specifications of the equipment. Acceptable paper Feeder Media type Weight PLAIN, 60 - 105 g/m RECYCLED PAPER 16 - 28 lb. Bond 2 Maximum sheet capacity 277 sheets (64 g/m2, 17 lb. Bond) 250 sheets (80 g/m2, 20 lb. Bond) 231 sheets (81 - 105 g/m2, 21 - 28 lb.
Specifications of Equipment *1 *2 *3 *4 Duplex copying is not available. For making copies on the sticker labels, select “THICK 2” for the paper type. Printing on the back side of an envelope is possible only when the envelope is not a self-sealing envelope. When the Saddle Stitch Finisher is installed, the envelope exits to the exit tray of the equipment. When the Inner Finisher is installed, the envelope exits to the receiving tray of the finisher.
Chapter 6 INFORMATION ABOUT EQUIPMENT e-STUDIO2050C/2550C, e-STUDIO2051C/2551C Specifications Model name Type Original glass Printing (copying) system Developing system Fixing method Photosensor type Original scanning system Original scanning sensor Scanning light source Scanning Resolution Writing Acceptable originals Acceptable original size Acceptable copy paper size Drawer Bypass Acceptable copy Drawer paper weight Bypass First copy time Black-and-white (A4 or LT Color portrait) Continuous copy speed
Specifications of Options Specifications of Options This section describes the specifications of the options sold separately. For details other than the specifications, see & P.64 “Options” in this manual. Reversing Automatic Document Feeder Model name Copy sides Number of originals (A4 or LT) Feeding speed MR-3024 1-side, Duplex 100 originals (35 - 80 g/m2, 9.3 - 20 lb. Bond) or 16 mm/0.63" or less in height (more than 80 g/m2, 20 lb. Bond) 45 sheets/min.
Chapter 6 INFORMATION ABOUT EQUIPMENT Paper Feed Unit Model name Acceptable paper size Paper weight Maximum capacity Power source Dimensions Weight MY-1040 A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP, 8.5"SQ, 13"LG, 8K, 16K, 16K-R (Non-standard size are not acceptable.) 60 - 163 g/m2 (16 lb. Bond - 90 lb. Index) 550 sheets (80 g/m2, 20 lb. Bond) DC 5 V, DC 24 V (supplied from the equipment) 575 mm (22.6") (W) x 583 mm (23.0") (D) x 163 mm (6.4") (H) (excl. Stabilizer) Approx. 9.
Specifications of Options Inner Finisher Model name Type Acceptable paper size Acceptable paper weight MJ-1036 Inner Finisher A3, A4, A4-R, A5-R, A6-R, B4, B5, B5-R, FOLIO, CHO-3 (120 mm x 235 mm), YOU-4 (105 mm x 235 mm), LD, LG, LT, LT-R, ST-R, COMP, 8.5"SQ, DL (110 mm x 220 mm), COM10 (4 1/8" x 9 1/2"), Monarch (3 7/8" x 7 1/2"), 13"LG, 8K, 16K, 16K-R 60 - 209 g/m2, 16 lb. Bond - 110 lb. Index Number of sheets stapled at a time (Including 2 covers (106 - 209 g/m2, 29 lb. Bond 110 lb.
Chapter 6 INFORMATION ABOUT EQUIPMENT Hole Punch Unit Model name Acceptable paper size Acceptable paper weight Dimensions Weight MJ-6008 Series A3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, COMP, 8.5"SQ, 13"LG, 8K, 16K, 16K-R 60 - 128 g/m2, 16 lb. Bond - 34 lb. Bond (OHP film and specially treated paper are not available.) 126 mm (4.96") (W) x 463 mm (18.23") (D) x 174 mm (6.85") (H) (excl. Lower cover) Approx. 3.4 kg (7.5 lb.
Specifications of Options FAX Unit Model Name Size of Original Recording Paper Size Compatibility Communication Modes Communication Resolution Transmission Rate Encoding Systems Memory Capacity Unit Type Applicable Network GD-1320 A3, A4, A4-R, A5, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST, ST-R, COMP 297 mm x 420 mm (A3), 210 mm x 297 mm (A4), 148 mm x 210 mm (A5), 257 mm x 364 mm (B4), 182 mm x 257 mm (B5), 210 mm x 330 mm (FOLIO), 11" x 17" (LD), 8.5" x 14" (LG), 8.5" x 11" (LT), 5.5" x 8.
78
INDEX A, B O, P Acceptable paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 [ACCESS] button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Additional Drawer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64, 73, 74 Adjusting the angle of the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Alarm lamp. . . . . . . . . . . . . . . . . . . . . . . . . . .
©2012 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TTEC.
Printed in China FC-2050C/2550C FC-2051C/2551C OME12000200
MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS Quick Start Guide 2012 TOSHIBA TEC CORPORATION All rights reserved 6LJ60754000 R120120K8301-TTEC (SYS V1.
