LCD TV/DVD COMBINATION 32DV733R OWNER’S MANUAL Owner’s Record The model number and serial number are on the back of your TV/DVD. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV/DVD. ©2010 Toshiba Corporation Before operating the unit, please read this manual thoroughly.
Precautions CAUTION: THIS UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE UNIT. CLASS 1 LASER PRODUCT WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
Contents Precautions ................................................................................................................................................................................ 2 Important safety information ........................................................................................................................................................ 5 Location of controls ...........................................................................................................
Contents Status message ......................................................................................................................................................................... 82 Troubleshooting table ................................................................................................................................................................ 83 Specifications ..................................................................................................................
Important safety information This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers related to such use. • Although this unit has been carefully manufactured and rigorously checked prior to leaving the factory as with all electrical appliances, it is possible for problems to develop.
Important safety information (continued) Where to install Locate the television away from direct sunlight and strong lights; soft and indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight from falling on the screen. Always place the TV on a sturdy, level, stable surface that can support the weight of the TV.
Important safety information (continued) Please take note If stationary images generated by text services, channel identification logos, computer displays, video games, on-screen menus, etc. are left on the television screen for any length of time, they could leave an afterimage. It is always advisable to reduce both the brightness and contrast settings.
Location of controls 1 2 3 5 6 4 12 13 7 8 9 10 11 14 Description of indicators and controls 1. 2. 3. 4. POWER indicator: The Power indicator lights red in standby mode, orange in standby mode when the timer is activated, and green when TV is powered on. Remote sensor Auto Brightness Sensor: This sensor will detect the ambient light conditions to optimise the backlighting level (see page 13). Disc slot: Load the disc into the disc slot to view or listen. 5. 6. 7. EJECT: Press to eject a disc.
Remote control Function Page Eject a disc from the disc slot 54 Toggle between TV and DVD mode 16, 53 Toggle between analogue TV and digital TV 16 Toggle between power on and standby mode 16 - Select a channel - Select a teletext page - Enter the password Display source information 23 25 44, 76 24, 50, 61 Turn the sound on/off 23 Toggle between TV, Radio, and Data modes 23 Select an input source 18 - Change the TV channel or teletext page up or down - In standby mode: turn on the power 23
Remote control (continued) Install the batteries Use R03/AAA/UM4 batteries. Note: • Weak batteries can leak and severely damage the remote control transmitter. Always remove batteries if they become weak or if the remote control is not to be used for an extended period of time. • Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such batteries. Replace exhausted batteries with new ones. Never try to recharge normal batteries - this could cause an explosion.
I/O connections Note: Before you connect other appliances: • To avoid potentially damaging your TV, make sure all items are switched off and disconnected from the mains power when you make the connections. • Arrange the desired connection. • When you have finished making the connections, reconnect the mains power to the TV and switch it back on. Connect your aerial as shown below. Connections to other equipments is explained further on pages 77-81.
DVB-C function notice DVB-C (Digital Video Broadcasting - Cable) is the DVB European consortium standard for the broadcast transmission of digital television over cable. This system transmits an MPEG-2 or MPEG-4 family digital audio/video stream, using a QAM modulation with channel coding. Information for the DVB-C function • Any function relative to the digital television (with the DVB logo) is available only within the country or area where such signals are transmitted.
Using the Auto Brightness Sensor When the Auto Brightness Sensor feature is set to On, the TV will automatically optimise the backlighting levels to suit ambient light conditions. 1 Press MENU SETUP or DIGITAL MENU to display the Main Menu screen. Select Picture, and then press ENTER/CH LIST . Main Menu Picture Sound Channel Setup 2 Press / to select Auto Brightness Sensor, and then press / to select On or Off to confirm your choice.
Auto setup Your TV has an automatic installation routine which makes installation easy. When you turn on the TV for the first time, the automatic installation routine is activated. This routine helps you select the on-screen language, antenna or cable in, country, energy saving mode, and automatically search for and store all available analogue and digital (DVB) channels. The automatic station presetting feature is for the TV’s built-in tuner only. If you have a device such as a digital decoder (e.g.
Auto setup (continued) 6 Press / to select Auto Tuning, and then press ENTER/CH LIST . Connect aerial to TV then press ENTER to start auto tuning A message prompt will appear with option to connect aerial to TV. EXIT : End 7 Press ENTER/CH LIST to start Auto Tuning. Your TV will now automatically detect all available channels in your area and store them in the TV’s memory. Analogue channels will be scanned first, and then digital channels.
*DTV auto tuning/Setting Antenna or Cable Preparations: Auto Tuning will completely re-tune your TV and can be used to update the channel list. It is recommended that DTV auto tuning is run periodically to ensure new services are added. If the • Turn on the TV with the setting of Ant/Cable In is changed the Auto Tuning screen will automatically appear. All current button on its left programmes and settings will be lost. side.The power Press INPUT to select ATV or DTV, and then press ENTER/CH LIST .
*DTV auto tuning/Setting Antenna or Cable (continued) (2) The auto scan process will now begin. A progress bar appears to indicate scanning progress. DTV Channel Found 0 Radio Channel Found 0 Frequency(kHz) 642000 EXIT : Cancel * Setting Cable: (1) When Ant/Cable In is set to Cable, a list of setting options will be displayed. Note: • All the channels will be deleted before the scanning process begins. • You can cancel the scan process at any time by pressing EXIT/CANCEL .
Selecting the video input source Selecting the video input source 1 Press INPUT to view a signal from the device connected to your TV, such as a VCR or DVD player. You can select each input source according to the devices you have connected to your TV. 2 Press / or the corresponding number on the screen to select a video input source, and then press ENTER/CH LIST within 5 seconds.
Automatic station presetting with the built-in tuner Automatic station presetting with the built-in tuner Perform this feature to search for and store new analogue and digital TV programmes after the Automatic Installation (see pages 14-15). Preparation: Make sure your antenna is connected to the aerial input (see page 11). Select ATV or DTV (see page 16), and then press MENU SETUP 1 2 Press / or DIGITAL MENU .
Changing the order of stored channels Changing the order of stored channels The Automatic station presetting stores channels in a specific order. However, this order can be changed if you wish. 1 Press MENU SETUP or DIGITAL MENU to display the Main Menu screen. Select Channel, and then press ENTER/CH LIST . 2 3 Press / to select Ch Allocation, and then press ENTER/CH LIST Press / to select a channel allocation option, and then press ENTER/CH LIST . .
Manual TV station presetting The Auto Tuning process stores all available stations in the reception area. However, some stations with weak or poor reception may not be detected. If this is the case and you still want to store these stations in your TV, press the ATV/DTV button to enter ATV or DTV mode, and then follow the steps below. 1 2 3 4 Press MENU SETUP or DIGITAL MENU to display the Main Menu screen.
Manual TV station presetting (continued) • *When Ant/Cable In is set to Cable, the following information will be displayed: - Frequency(kHz): A specific frequency can be input for scanning. - Symbol Rate: A specific baud rate (KS/s) can be input for manual scanning. - Modulation: Select from five QAM modulation options After setting the channel, press ENTER/CH LIST Frequency(kHz) Symbol Rate Modulation to start scanning for channels.
Basic operation Channel selection Use the number buttons 0-9. For example: • CH 2: Press 0 and within 2 seconds, press 2. The TV will switch to CH 2. • CH 29: Press 2 and within 2 seconds, press 9. The TV will switch to CH 29. (1) Press CH / to select a channel. This takes approx. 2 seconds to switch from one channel to another. Only channels saved in the TV and are active can be displayed. Skipped channels will not appear (see page 20). The Channel List shows a list of all receivable programmes.
Basic operation (continued) Information display In ATV mode: Press to display the channel number and sleep timer settings information on the screen. Current settings for the sound mode, picture size, and resolution (if in use) are also displayed. The information will appear for approx. 5 seconds. Sleep Timer 1h 40m 11 BBC1 NICAM ST Auto 576i In DTV mode: When you switch channels, a channel banner is displayed for a few seconds.
Teletext A teletext service offers a range of text-based information, typically including news stories, sport articles, weather forecasts, and TV schedules. Information is sent page by page. The TV can store up to 256 pages, but they can only be accessed once they have been stored. Fastext/TOPtext Hold page The Fastext/TOPtext is teletext with a special directory. On the lower part of the screen there are four different coloured fields (red, green, yellow, and blue).
Stereo reception with the built-in analogue tuner The TV’s built-in tuner can detect and receive NICAM stereo broadcasts automatically. NICAM stereo sound reception 1 2 Press MENU SETUP to display the Main Menu screen. Press / to select Sound, and then press ENTER/CH LIST . Sound Select NICAM, and then press / to select Auto or Off. Select Off if you do not want to receive NICAM sound.
Picture format The broadcaster may transmit a widescreen signaling (WSS) signal which can determine the correct height/width of pictures and have it set automatically when the setting Auto is selected. If you want to change this setting, you can select from the formats listed below. Auto picture size Press PIC SIZE repeatedly until Auto appears on the screen. Picture format setting Press PIC SIZE repeatedly to scroll through the following options.
AV colour adjustment Use the AV Colour menu option to adjust the picture colour settings in AV mode. These settings do not apply when the TV is in any other mode. 1 Press INPUT to select AV1 or AV2, and then press ENTER/CH LIST . ATV DTV AV1 AV2 Component HDM1 HDM2 Note: • DVD players that play NTSC DVDs (i.e. multiregion/region code-free) can produce different signals based on the player model. Possible signals include PAL, SECAM, NTSC3.58, NTSC4.43 and PAL60.
Other convenience functions The TV Main Menu has several menu options you can configure to suit your viewing preferences. Main menu Picture Selected items Picture Setting Brightness Adjust the black level. This aspect determines the point where grays become pure black. Contrast Adjust the white level. This aspect determines how bright the brightest whites should appear. Sharpness Adjust the sharpness or softness of the display. Colour Adjust the colour intensity.
Other convenience functions (continued) Main menu Channel Setup Selected items Ant/Cable In Antenna/Cable Select a country in which you live. Auto Tuning Perform an automatic channel search. See pages 16-17, and 19. Manual Tuning Perform a channel search for stations with weak or poor signal. See pages 21-22. Ch Allocation Customise the channels stored in the TV. See page 20.
Other convenience functions (continued) Auto 4:3 Default*1 4:3/16:9 See page 43. Display Setup*2 Auto Shut Off No Signal No Operation *2 *3 This option automatically shuts the TV off when no signal has been detected for 15 minutes (not applicable to DVD mode), or no button has been pressed for 4 hours. AV Colour*3 Auto/ PAL/ SECAM/ NTSC4.43/ NTSC3.58/ PAL60 Select the colour system for the display when using signal from the audio/ video terminals. See page 28.
Using REGZA-LINK® This is a new feature that uses CEC technology and allows you to control Toshiba REGZA-LINK® compatible devices from the TV remote via HDMI connection (see page 79). When the Enable REGZA-LINK in the REGZA-LINK Setup menu (see page 35) is set to On, the following REGZA-LINK® functions will be enabled. REGZA-LINK® playback device (DVD player, etc.
Using REGZA-LINK® (continued) REGZA-LINK® Player menu 1 2 Press MENU SETUP Press / or DIGITAL MENU to display the Main Menu screen. to select Setup, and then press ENTER/CH LIST Main Menu Picture . Sound Channel Setup 3 Press / to select REGZA-LINK Player, and then press ENTER/CH LIST 4 Press / .
Using REGZA-LINK® (continued) REGZA-LINK® input source selection If a REGZA-LINK® device with HDMI switching capability (e.g. Audio Receiver) is connected to the HDMI input, you can select another REGZA-LINK® device that is connected to the master HDMI device using INPUT on the remote control or INPUT/ENTER on the TV control panel. VOLUME and MUTE controls of Audio Receiver With your TV’s remote control, you can adjust or mute the sound volume of a REGZA-LINK® compatible Audio Receiver.
Using REGZA-LINK® (continued) Other REGZA-LINK® functions When the Enable REGZA-LINK and each item in the REGZA-LINK Setup menu are set to On, the following functions will be enabled. TV Auto Input Switch If a connected HDMI device starts playing video or audio, the TV will automatically switch to the appropriate HDMI input.
Using the Media Player The TV allows you to enjoy photos and music stored on a USB device. Media Player information Required device USB device: USB Mass Storage Class devices (MSC) Note: • Connectivity is not guaranteed for all devices. • Connect the USB device to the TV directly. • Do not use a USB hub. Media Player playback reminders • • • • • The file systems supported by Media Player are FAT12, FAT16, and FAT32. The maximum number of files stored in each folder is 2000.
Using the Media Player (continued) Basic operation Auto Start 1 2 Press MENU SETUP to display the Main Menu screen. Press / to select Setup, and then press ENTER/CH LIST . Press / to select Media Player, and then press ENTER/CH LIST . 3 Press / / to select Auto Start, and then press to select On.
Using the Media Player (continued) Viewing JPEG files Single View mode 1 Press MENU SETUP screen. 2 Press / to select Setup, then press / to select Media Player, and then press ENTER/CH LIST 3 Press to display the Main Menu . / to select Photo, and then press ENTER/CH LIST REGZA-LINK Setup >> REGZA-LINK Player >> Media Player >> Language Setup >> Subtitle and Audio >> Audio Description >> Media Player .
Using the Media Player (continued) Using the photo Quick Menu You can select your preferred photo viewing settings from the photo Quick Menu. 1 From the photo Single View, Slide Show or thumbnail mode, press MENU SETUP enter the Quick Menu. to Note: • The Quick Menu items of thumbnail and Single View/Slide Show modes are different. Note: • The sleep timer setting in the Media Player Quick Menu or TV Setup Menu will override the previous setting of each other.
Using the Media Player (continued) Setting background music for photo mode You can select music from the music list stored in the USB device to be played back in photo mode. 1 From the photo Single View or Slide Show mode, press MENU SETUP Quick Menu to enter the Quick Menu. Interval Time 5 sec Repeat Off Background Music Select Sleep Timer >> Off : Adjust 2 Press / to select Background Music Select, and then press ENTER/CH LIST Quick Menu .
Using the Media Player (continued) Listening to MP3 files Besides viewing JPEG files, you can also listen to the music files stored in the USB device. 1 From Media Player menu, press / to select Music and then press ENTER/CH LIST . 2 3 4 When the list appears, press Press ENTER/CH LIST folder. Press RETURN folder. / to select a file or folder. to begin playing the selected music file or to open the selected or the first folder named “..
Using the Media Player (continued) Using the music Quick Menu You can select your preferred music playback settings from the music Quick Menu. 1 From the music list or music playback mode, press MENU SETUP Menu. to enter the Quick Note: • The Quick Menu items of music list and music playback modes are different. 2 3 4 Press / to select the item you want to adjust. Press / to select your preferred setting.
Display setup/Timer setting (DTV mode only) Display Setup 1 2 3 Press MENU SETUP or DIGITAL MENU to display the Main Menu screen. Press / to select the Setup menu, and then press ENTER/CH LIST Press / to select Display Setup, and then press ENTER/CH LIST . Display Setup . The Display Setup menu appears. Banner Timeout 4 sec. Banner Position Bottom : Adjust 4 5 Press / / to select an item, and then press to change each setting. Banner Timeout 1 sec, 2 sec... 7 sec.
Password setup (Parental lock) (DTV mode only) Password Setup (Parental lock) This feature allows you to have parental control of services based on your viewing preferences. Once a service is protected with a password, it cannot be viewed unless the correct password is provided. 1 2 Press MENU SETUP or DIGITAL MENU Press / to select the Setup menu, and then press ENTER/CH LIST . Press / to select Password Setup, and then press ENTER/CH LIST . The Enter Password window will appear.
Version Version You can check the software version information. 1 2 3 Press MENU SETUP or DIGITAL MENU to display the Main Menu screen. Press / to select the Setup menu, and then press ENTER/CH LIST Press / to select the Version menu, and then press ENTER/CH LIST . . Note: Timer Setting >> Password Setup >> Version >> Software Upgrade >> Common Interface >> • Version check also applies to ATV mode. ENTER : Set The software version will be displayed. Version V0.01.
Software upgrade (DTV mode only) Software Upgrade Software Upgrade allows you to download the latest software available for the channel. 1 2 3 Press MENU SETUP or DIGITAL MENU to display the Main Menu screen. Press / to select the Setup menu, and then press ENTER/CH LIST Press / to select Software Upgrade, and then press ENTER/CH LIST . to select Start to check if the TV has the Over Air Download service.
Common interface (DTV mode only) Common Interface You can access the Common Interface module information from this menu option. Preparations: Insert CAM into the DVB Common Interface (C.I.) slot on the side of the TV (see page 8). 1 2 3 Press MENU SETUP Press / or DIGITAL MENU to display the Main Menu screen. to select the Setup menu, and then press ENTER/CH LIST . Press / to select Common Interface, and then press ENTER/CH LIST .
Multi audio (DTV mode only) Multi audio The Multi audio menu enables you to choose your preferred audio mode and DVB (Digital Video Broadcasting) subtitle languages available for the current broadcasting programmes. 1 Press AUDIO SELECT to display the Multi audio menu. The Audio mode and Language Code will be displayed, if available. Multi audio Audio mode Stereo No. Language Code 001 English : Adjust 2 Press / to select Audio mode. The Audio mode options include: Stereo, Left, Right, and L + R.
DVB-Subtitle (DTV mode only) DVB-Subtitle DVB-Subtitle is a feature supported by DVB (Digital Video Broadcasting) applications. It provides on-screen text display in parallel with the corresponding audio services, and can be enabled or disabled at any time. 1 Press SUBTITLE menu. to display the Subtitle Subtitle Language English : Adjust 2 Press / to select your preferred subtitle language from the available languages.
EPG (Electronic Program Guide) (DTV mode only) The Guide menu shows a list of available programmes for the next eight days only, including today. However, it will show “No Event Name” for programmes which are more than eight days ahead, or for programmes within the eight days when no programme information is available. 1 Press GUIDE 2 Press TV/RADIO to toggle between three service modes -TV, Radio, and Data - to view the EPG data accordingly. By default, the services listed on the screen is TV mode.
EPG Timer (DTV mode only) You can choose whether or not to switch on your TV screen when a timer event begins (see page 31: Rec Screen Status (LCD Power on/off)). This is so that if you are using the timer to make a recording from your VCR or other device, the TV screen will not turn on unless you want it to. If you try to interrupt your event timer in any way, e.g.
Disc DVD discs must be Region 5 or Region ALL type to play on this TV/DVD. If region numbers, which stand for their playable area, are printed on your DVD and you do not find or , disc playback will not be allowed by the player. (In this case, the TV/DVD will display a message on-screen). Some DVDs that have no region code label may still be subject to area restrictions and therefore not playable.
Basic playback This section shows you how to play a disc. Basic playback (DVD/VCD/Audio CD) 1 Press on the TV control panel or on the remote control to turn on the TV. The power indicator on the front of the TV will change to green. 2 Press TV/DVD on the remote control to switch to DVD mode. The DVD startup screen will appear on-screen. 3 Hold the disc by its edges and load it in the disc slot with the label side facing forward. (If the disc has a label.
Basic playback (continued) To start playback in stop mode Press PLAY . To pause playback (still mode) Press PAUSE during playback. To continue playback from still mode Press PLAY . To stop playback Press STOP . To remove a disc 1 2 Press EJECT on the TV control panel or on the remote control. Wait for the disc drive to eject the disc, and then remove the disc from the slot. Disc playback reminders • If the TV does not operate properly, static electricity build-up may be the cause.
Advanced playback The TV supports several playback modes that allow you to play discs at various speeds. Playing in fast reverse or fast forward direction (DVD/VCD/Audio CD) 1 Press REV / FF during playback. • REV : Fast reverse playback • FF : Fast forward playback Each time you press REV / FF , the playback speed changes. 2 To resume normal playback, press PLAY . Note: • The sound is muted during reverse and forward scan. • The playback speed may differ depending on the disc.
Zoom function/Scene navigation Using the Zoom function (DVD/VCD) You can change the viewing scale of a picture by using the Zoom function. Once the image has been rescaled, use the arrow buttons / / / to pan the image. 1 Press CH RTN ZOOM during playback. The view will zoom into the centre of the image. 1 Each press of the button will increase the scale value: 1(x 1.3), 2 (x 1.5), and 3 (x 2.0). 2 3 Press / / / to pan the scene and view different sections of the picture.
Scene bookmark Bookmarking a scene (DVD/VCD/Audio CD) Scene bookmarks refer to specific points in the playback range that have been marked for later access. You can create up to three markers per disc. Note: • The saved scene bookmarks are only accessible during the current session. Once you eject the disc or turn off the TV, all bookmarks will be cleared. 1 2 Note: • Bookmark function is not applicable to JPEG CD/ DivX® CD.
Repeat playback/A-B repeat playback Enabling repeat playback (DVD/VCD) You can choose to repeat DVD playback by title or chapter. For VCDs, you can repeat a single track or the entire disc. 1 2 Press PLAY MODE during playback or stop mode. DVD [DVD] Press ENTER/CH LIST repeatedly to select a repeat mode. It can either be by Chapter or by Title. The TV automatically starts repeat playback after finishing the current title or chapter.
Scene angle/Title selection/DVD menu Changing the scene angle (DVD) When playing back a DVD recorded with multi-angle scenes, you can select the scene angle that you prefer. 1 Press ANGLE during playback. The current angle will appear. 2 Press ANGLE 1/2 repeatedly until the preferred scene angle is displayed. Note: • Depending on the DVD, you may not be able to change the scene angle even if multi-angle data are recorded on the disc. Selecting a DVD title (DVD) Some DVDs contain two or more titles.
Soundtrack language/Audio channel/Subtitle Selecting a soundtrack language (DVD) You can select the soundtrack language when you play a multilingual DVD. During playback, press AUDIO SELECT repeatedly 2/2 until the preferred language is selected. D 5.1 Ch Eng Selecting the audio channel (VCD) During playback, press AUDIO SELECT repeatedly until the preferred audio channel is heard. Options include Stereo, Left, Right, and Mix.
Playback information/VCD playback control (PBC) Viewing the playback information (DVD/VCD) You can view the playback status and other disc information. Press to display the status of the disc during playback. To close the display panel, press again. VCD mode Elapsed/remaining time for disc Elapsed/remaining time for current track VCD2.0 Time DISC 00:00:19/00:16:12 Track 1/8 Track 00:00:19/00:02:28 Track no.
MP3/JPEG/DivX® and Audio CD operation This TV can play MP3/JPEG/DivX® files recorded on CD-R and CD-RW discs. To create an MP3/JPEG/DivX® disc, you need a Windows PC with a CD-RW drive and file encoding software (not supplied). This TV requires discs/recordings that meet certain technical standards in order to achieve optimal playback quality. There are many different types of recordable disc formats (including CD-R discs containing MP3 files). Not all recordable discs will produce optimal playback quality.
About the file browser/Audio file playback About the file browser Operation status Filename of selected item Scroll bar Select files Option panel File list Music Playing Selection highlight Preview panel File icons Music file (MP3 or audio CD track) Picture file (JPEG) Movie file (DivX® video) If a CD contains a mixture of MP3, JPEG, and DivX® files, and PLAY is pressed without selecting a file, playback starts automatically from the first file in the list.
Playing an audio file 1 Load an MP3 or audio CD in the disc slot. The file browser appears on-screen. The first audio file in the list plays automatically (applicable only to audio CD). Select files Folder- 1 Folder- 2 MP3- 1 MP3- 2 MP3- 3 WMA- 1 JPEG Preview WMA- 2 WMA- 3 2 Press / playback. to select another audio file for Folder- 1 Select files Folder- 2 MP3- 1 MP3- 2 MP3- 3 WMA- 1 JPEG Preview WMA- 2 WMA- 3 3 Press ENTER/CH LIST or PLAY to start playback. To stop playback: Press STOP .
JPEG file operation Viewing a JPEG file 1 Load a disc containing JPEG files in the disc slot. The file browser appears on-screen. 2 Press / to select an image file for viewing. A preview of the selected file is displayed in the Preview panel. /Picture-01.JPG Picture-01 To display a thumbnail list: Press DVD MENU , and then press select an image file.
DivX® and DivX® VOD operation DivX® playback 1 Load a disc containing DivX® files in the disc slot. The file browser appears. 2 Press / to select a file for playback. When PLAY is pressed without selecting a file, playback starts automatically from the first file in the list. /Movie-01.
MP3/JPEG/DivX® and Audio CD playback modes Enabling repeat playback (Audio CD/MP3/JPEG/DivX®) You can choose to repeat CD playback by track or the entire disc. 1 During stop mode, in the Option panel of the file browser, press / to select Repeat. Select Files Fo lder-1 Repeat Fo lder-2 Off MP3-1 2 Press ENTER/CH LIST mode: Track or All. repeatedly to select a repeat Select Files Fo lder-1 Repeat Fo lder-2 Note: • These playback modes are only applicable during the current session.
MP3/JPEG/DivX® and Audio CD playback modes (continued) Programming the playback sequence (Audio CD/MP3/JPEG/DivX®) You can customise the file playback sequence. 1 2 Note: • The programme playback mode is only applicable during the current session. Once you eject the disc or turn off the TV, this mode will be disabled.
Programme playback/Random playback The TV enables you to arrange the playback order of tracks and files on the disc, and it can also select tracks and files at random and playback them. These features can be applied for Video CD. For Audio CD and MP3/JPEG/DivX® CD, please see “Enabling random playback (Audio CD/MP3/JPEG/DivX®)” on page 67 and “Programming the playback sequence (Audio CD/ MP3/JPEG/DivX®)” on page 68. Enabling programme playback (VCD) 1 Press PLAY MODE during stop mode.
Customising disc playback You can customise the disc playback settings to suit your preferences. Configuring the disc playback settings (DVD/VCD/CD) 1 In DVD mode, press MENU SETUP mode. during stop Parental DRC E.B.L. Menu : :English Off QSound TV Screen Set Password : :English On 4:3 Subtitle Output Display DivX Subtitle : :ASCII Interlace On Audio :English Picture Mode DivX(R) :VOD Auto OSD JPEG Interval Screen Saver 2 Press / to select a setup tab, and then press .
Customising disc playback (continued) Settings details Section Option Details Page Menu Select the language for the DVD menu display. 72 Subtitle Select the subtitle language for disc playback. DivX Subtitle Select the subtitle encoding format for DivX® VOD playback. Audio Select the audio language for disc playback. OSD Select the language for the Setup screen display. Display Choose whether to show a status display whenever a button 72 is pressed.
Customising disc playback (continued) Menu / OSD Select the language for the DVD and Setup menu display. Options include: English, Spanish, German, Italian and Russian. Subtitle / Audio Menu Parental DRC E.B.L.
Customising disc playback (continued) Night Mode Select to toggle the Night Mode feature on or off. When enabled, this function allows for automatic volume level adjustment for audio that may be too low (e.g. whispered dialogues) or too high (e.g. a thunderstorm scene). • Off: Audio retains its disc recording volume level. • On: Volume level is automatically adjusted depending on the scene content. Night Mode Parental Menu E.B.L.
Customising disc playback (continued) Parental A DVD is usually encoded with a rating level to indicate the recommended audience age. You have the option to select the content rating level allowed for playback in your TV. You will be prompted to key in the system password to access this setting option. For initial access to this menu: Parental DRC Menu E.B.L.
Customising disc playback (continued) Password Select this option to change the access password for the parental control setting. (1) Press . / to select Password, and then press ENTER/CH LIST The Enter Current Password screen will appear. (2) Use the number buttons (0–9) to input the current password, and then press ENTER/CH LIST . If the password has not been set yet, key in “0000”. This is the factory default password. (3) Press ENTER/CH LIST again, and then Enter New Password screen will appear.
Temporary cancel the rating level by DVD disc 1 Load a DVD disc. 2 If the DVD disc has been designed to temporarily cancel the rating level, the screen which follows the Reading screen will change, depending on which disc is played. If you select Yes and press ENTER/CH LIST , the password input screen will then appear. 3 Use the number buttons (0–9) to input the password, and then press ENTER/CH LIST . 4 Enter Password Playback will start if the entered password is correct.
PC connection As PCs are sometimes supplied with a “conventional” CRT monitor, you may need to adjust the display settings of your PC’s graphic card; otherwise the pictures may not appear correctly. Switch on your PC (still with your original monitor), select “1360 x 768” for the screen resolution, and select “60 Hz” for the on-screen refresh rate. Switch off your PC, and then connect it to your TV while both items are switched off. Monitor display modes Mode Resolution V. Frequency H.
Connecting an HDMI or DVI device to the HDMI input The HDMI input on your TV receives digital audio and uncompressed video from an HDMI-equipped device, or uncompressed digital video from a DVI-equipped (Digital Visual Interface) device. TV（Back side view） HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
REGZA-LINK® connection You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a REGZALINK® compatible audio receiver or playback device. For an explanation of setup and operations, see pages 32-35.
Connecting TV to other equipment 1 Connecting aerials and other devices to your TV Connect the TV’s coaxial cable directly to the aerial input jack at the back of the TV.
Connecting TV to other equipment (continued) 3 Connecting a DVD player DVD player can be connected to the TV either by a SCART cable or a standard audio cable along with a component video cable (see 5 on this page). SCART cable (not supplied) TV（Back side view） To AV1 input In this case, a SCART cable is required for the connection. To play the DVD, select AV1 input mode on the TV (see page 18).
Status message Information/Status message Cause Invalid entry The channel does not exist (e.g. “000”). No radio services Cannot change to Radio mode because there is no radio service in the channel list. No TV services Cannot change to TV mode because there is no TV service in the channel list. No data services Cannot change to Data mode because there is no data service in the channel list. No services There are no services in the received signal.
Troubleshooting table Refer to the following checklist to troubleshoot simple problems that may occur during TV operation. If the problem still exists after you try out the possible solutions, consult your local dealer or service outlet for assistance. Check that all connections are properly made when using the TV with another equipment. Symptom Possible solution Page • • • • Make sure the power cord is plugged in, and then press POWER. Try another AC outlet.
Troubleshooting table (continued) X appears on the screen. • The function is not applicable to the disc or to the current mode. 54 No picture. • The TV is not in DVD mode. 53 No sound. • The TV is in a special playback mode. • If you are using an amplifier, check the optical digital audio out connection. • If an external speaker is connected, check its volume control. 55 80 - Picture is distorted during fast reverse/forward playback. • The picture will be distorted occasionally. This is normal.
Specifications Model Television LCD panel (approximate screen size, diagonal) System Analogue Digital Video colour system Preset channels Frequency range Analogue Digital LCD Speaker Audio output power DVD Signal system Applicable disc Output Pickup 32DV733R 32.0 inch PAL UK, IR, CCIR, French System, B/G, D/K, I/I, L/L’ DVB-T (OFDM 2k/8k 16QAM/64QAM) PAL/SECAM/NTSC 3.58/NTSC 4.
The GNU General Public License (GPL) Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
NO WARRANTY (1) BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
The Libpng License Notices This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail. COPYRIGHT NOTICE, DISCLAIMER, and LICENSE: If you modify libpng you may insert additional notices immediately following this sentence. This code is released under the libpng license. libpng versions 1.2.6, August 15, 2004, through 1.2.
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative. Glenn Randers-Pehrson glennrp at users.sourceforge.net December 3, 2009 The zlib License zlib.h -- interface of the “zlib” general purpose compression library Version 1.2.3, July 18th, 2005 Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler This software is provided “as-is”, without any express or implied warranty.
Следующий символ означает, что данное изделие не может утилизироваться как бытовые отходы. При надлежащей утилизации изделия вы помогаете предотвратить негативное воздействие на окружающую среду и здоровье человека. Для получения подробных сведений об утилизации данного изделия обратитесь в администрацию своего города, местную компанию по сбору отходов или в магазин, где вы приобрели данное устройство. The use of the symbol indicates that this product may not be treated as household waste.
