Contents Introduction Welcome to Toshiba ...........................................................3 Important Safety Instructions .............................................3 Installation....................................................................3 Use ..............................................................................4 Service..........................................................................5 Cleaning .......................................................................
Introduction Welcome to Toshiba • Thank you for purchasing this Toshiba LCD Color television. This manual will help you use the exciting features of your new TV. • Instructions in this manual are based on using the remote control. • Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference. Important Safety Instructions 4) Never block or cover the slots and openings in the cabinet. • Never place the TV so that it is facing upward or on its side.
Introduction 8) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. To secure the TV, use a sturdy strap from the hooks on the rear of the TV to a wall stud, pillar, or other immovable structure. Make sure the strap is tight, secure, and parallel to the floor. 9) Precautions for moving the TV • When moving the TV, be sure to remove the plug from the wall outlet and disconnect the antenna cable and audio/video cables, any steady ties.
Introduction 5) When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet for safety. • The TV is not completely disconnected from the power supply line, as minute current is consumed even when the Power switch is turned off. • The Mains plug or an appliance coupler is used as the disconnect device, therefore the disconnect device shall remain readily operable. Service 1) Never repair, modify or disassemble the TV by yourself.
Introduction Important information Cleaning 1) Remove the power plug before cleaning. Never use solvents such as benzine or thinner to clean the TV. • These solvents may distort the cabinet or damage its finish. • If rubber or vinyl products remain in contact with the TV for a long time, a stain may result. If the cabinet becomes dirty, clean it with a soft, dry cloth. When cleaning the surface of the LCD display, wipe the panel surface gently with a soft, dry cloth.
Getting started Connecting an antenna Exploring your new TV Optimum reception of color requires a good signal and will generally mean that an outdoor antenna must be used. The exact type and positioning of the antenna will depend upon your particular area. Your Toshiba dealer or service personnel can best advise you on which antenna to use in your area. Before connecting the antenna cable, turn off all main power switches. VHF Installing the remote control batteries Remove the battery cover.
Getting started TV front, control and side panel • You can operate your TV using the buttons on the TV control panel or the remote control. The back and side of the panel provide the terminal connections to connect other equipment to your TV (- “Connecting your TV” pages 29 - 32). • For the use of each control, see the pages in brackets.
Getting started TV back panel connections 26AV500A 32AV500A 37AV500A 42AV500A 32”/ 37” TV 26”TV 1 HDMI1,2 (input terminals) — High-Definition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device ( page 29). 2 PC/HDMI1 (AUDIO) (input terminals) — For use when connecting a personal computer (PC) or a DVI device with standard audio output ( page 28, 30).
Getting started Learning about the remote control Location of controls Power on/Standby ( To select accordingly TV, STB or DVD mode Number buttons (0-9) ( pages 16, 22) Input source selection (DTV,Video1,Video2,HDMI1, HDMI2,PC and ATV.) page 23) ( To return to the previous program ( page 16) To switch between Analog and Digital TV ( page 11) Program position ( page 16) Volume – + (These buttons adjust the volume level.) MENU (. • Menu • OK ( Sound mute (This button turns off/on the sound.
Getting started This integrated TV is equipped with both Digital and Analog system. To switch between Digital and Analog TV press A/D on the remote control. TV SETUP menu chart Learning about the menu system PICTRUE menu We suggest you familiarize yourself with the display charts before using the menu system: to display menu, then press Y or Z to select main menu headings. • Press U or V to select sub manu headings. to select or adjust setting. • Press to display the next menu.
Getting started About ATV Menu Turning the TV on Switching on the TV Connect the power cord to a wall outlet, the indicator lights in red (standby mode). 1 power Press on the remote control or on the TV control panel, the power indicator lights in green. Switching off the TV 1 Press on the remote control or on the TV control panel to switch to the standby mode. Notes: • This TV is not fully disconnected from the main supply, as minute current is consumed even when is turned off.
Getting started Tuning the TV for the first time Before switching on the TV, put your decoder and media recorder to Standby if they are connected and ensure the antenna is connected. To setup the TV use the buttons on the remote control as detailed on page 10. 1 This screen will appear the first time that the TV is switched on and each time the TV is reset.
Getting started Manual Search - digital only - Auto Tuning - analog only - If there were any missing channel after Full Search, these channels might be found by using Manual Search described in this section. First, use the Auto Tuning function to preset all the active channels in your area automatically. Then, arrange the preset channels with the Manual Adjust function so that you can tune into desired channels. 1 2 From the Setup menu, press V or U to select Manual Search.
Getting started Manual Adjust - analog only Use the Manual Adjust operation if desired channels cannot be preset with the Auto tuning or if you would like to preset channels to specific position numbers one by one. 1 Channel List - digital only 1 From the SET UP menu, press V or U to select Channel List. DTV Menu...[Setup...Channel List] Language Country/Region From the SET UP menu, press V or U to select Manual Adjust. Full Search Quick Search Manual Search ATV Menu...[Setup...
Getting started 1 From the SET UP menu, Press Channel List. and V or U to select A. B. C. D. DTV Menu...[Setup...Channel List] Language Country/Region Full Search Quick Search 5 You can press to save edited channel program and to exit . press 6 to display the Fav When viewing in Digital TV, press Group channel list.
Getting started Watching TV programs Viewing Digital programs - digital only After you have tuned the TV, you have several ways to navigate through all programs: • Press the Number buttons (a channel number has 3-digits) and you may omit the leading zeroes, which will be appended automatically; (Please note that if you have channels with different frequencies but the same channel number, the TV will always tune to the first channel that has been stored into the channel database.
Using the TV’s features (General) 4:3 Picture adjustment Selecting the picture size 1 Each time you press , picture size information will Use this setting to view a true 4:3 broadcast may see bars on the top and bottom of the screen. change again. The information will disappear in variable time, which is dependent on banner duration setting. WIDE 2 Picture size will change as below mode: Wide, Super Live 2, Cinema 2,4:3, Super Live 1, Cinema 1, Subtitle and 14:9.
Using the TV’s features (General) Notes: • Using the special functions to change the size of the displayed image (e.g. changing the height/width ratio) for the purpose of public display or commercial gain may infringe on copyright laws. • If the aspect ratio of the selected format is different from the one of the TV transmission or video program, it can cause a difference in vision. Change to the correct aspect ratio picture size.
Using the TV’s features (General) Activating the DNR (Digital Noise Reduction) 3 If you want to adjust Backlight manually, turn Active Backlight Control to Off, then press V. 4 Press Y or Z to adjust the settings as required. If the receiving signal is weak and the picture is blurry, the picture may be improved when using this function. 1 2 From the Picture menu, press V or U to select DNR then press . PressV or U to select an item you want to adjust, pressY or Z to adjust the settings as required.
Using the TV’s features (General) Selecting the stereo programs - analog only - Sound adjustment Setting the MTS (Multi-channel TV Sound) 1 2 When a stereo program is received, Stereo appears. Press to select the Auto/Mono mode. Auto and Mono appear cyclically on the screen. - analog only - Auto mode The MTS Auto mode automatically recognize stereo/bilingual programs depending on the broadcast signal. 1 2 Press , then press Y or Z to display the SOUND menu then press .
Using the TV’s features (General) Using the Bass Boost 4 Press Z into the Timer data position and press V and U to set the time period. 1 From the SOUND menu, press V or U to select Bass Boost then press . Press to exit Menu. 2 Press Y or Z to select Off, Low, Mid and High. 5 6 Press on the remote control or control panel. Setting the Sleep Timer The Sleep Timer is especially useful if you want the TV to turn itself off after a selected period of time.
Using the TV’s features (General) Setting the Banner Duration - digital / analog 1 Press press 2 3 Press Vor U to select Banner Duration, then press . Press Y or Z to set Banner Duration which can be set 1 to 12 seconds. , then Y or Z to display the TIMER menu, then . Teletext in Analog TV This TV has a multi-page teletext memory, which takes a few moments to load and it offers two ways of viewing Teletext Auto and LIST which are explained below.
Using the TV’s features (General) Using Auto mode There are two Modes: Auto will display FASTEXT or TOPTEXT, if available. LIST will display your four favorite pages. In either mode, as an alternative to the colored buttons, you can access a page by entering a 3-digit number, using the Number buttons on the remote control, or to advance to the next page, press or U, to go back to the previous page or V. press To change between Auto and LIST, see above. • Press to access teletext. Ex.
Using the TV’s features (General) Teletext in Digital TV Reset all default setting 1 When any user require to reset adjustment values of the Picture, Sound, Setup, Timer and Function that can use Reset to default to back factory default setting. 2 3 When indicates the presence of Teletext (TTX) in a channel, press to view Teletext. Press again to superimpose the Teletext over a normal broadcast picture. Press again to close Teletext and watch TV. 1 and to select Teletext page.
Other Digital TV features and settings Setting the EPG (Electronic Program Password guide) - digital only In Digital TV, channels and programs can be locked to prevent 1 2 Press viewing of unsuitable films and programs. These can only accessed with a password. Default password is 0000. then Y or Z to select Function menu. Press andV or U to select EPG then, press display EPG. to DTV Menu...[FUNCTION...EPG] Setting the Password 1 Press , then press Y or Z to select the FUNCTION menu.
Other Digital TV features and settings AV Connection Audio Preference 1 Press menu. 2 Press and press V or U to select AV Connection, then press . , then press Y or Z to select the FUNCTION Selecting The Audio Mode 1 2 DTV Menu...[FUNCTION...AV Connection] Reset to default AV Connection Password Parental Rating Channel Lock EPG Video 1 CVBS Video 2 CVBS OK Confirm MENU Return 3 DTV Menu...[SETUP...
Connecting your TV Connecting an audio system - digital only - Back connections You can enjoy high quality dynamic sound by connecting the TV to an audio system. Connection example TV back view VCR (Recording) DVD video player (with component video outputs) or Notes: • DO NOT connect the DIGITAL AUDIO output terminal to the AC-3 RF input of a Dolby Digital Receiver with a built-in Dolby Digital decoder.
Connecting your TV Connecting an amplifier equipped with an MPEG decoder Side connections Connection example Amplifier equipped with MPEG decoder TV side view To Optical or Coaxial type digital audio input Optical or Coaxial digital cable (not supplied) TV back view Mini Stereo Plug • The audio from the speaker will be muted when connecting the headphone to this terminal.
Connecting your TV Connecting an HDMI device HDMI (type A connector)-to-DVI adapter cable One HDMI cable (type A connector) For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 3m. The recommended length is 2m. Standard analog audio cables TV back view An HDMI-to-DVI adapter cable transfers only video. Separate analog audio cables are required.
Connecting your TV • There is no need to use an adapter for computers with DOS/ V compatible mini D-sub 15 pin terminal. • A bar may appear in the upper, lower, right or left side of the screen, or parts of the picture may be obscured depending on some signals. This is not the malfunction. • If the edges of the picture are stretched, readjust the picture position adjustments in the VGA SET of PICTURE menu.
Reference section Troubleshooting Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions. Symptom and solution TV will not turn on • Make sure the power cord is plugged in, then press or . The brightness of the screen comes down, or flickers of the screen are caused, or some parts of the screen do not light up. • When you just buy and start to use this TV, a flickering may be caused in the screen.
Reference section APPENDIX AUSTRALIAN PARENTAL GUIDANCE CODES (Normative) Recommended On-Screen-Display for parental guidance codes transmitted within DVB-SI EIT information using the DVB parental_rating_descriptor.
Reference section Analog TV system (Antenna input) Broadcast system Channel coverage: PAL B/G (CCIR) Broadcast transmission systems of each country or region VHF 0 - 12 UHF 27 - 69 CATV C2, C10, C31, S2 - S44 Digital TV System Asia M.E. Country or region Color Sound Bahrain, Kuwait, Israel, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, etc.
Reference section Input/Output terminals (1) Input RCA Component Video RCA Composite Video Audio : RCA Y, PB/CB, PR/CR CVBS L/Mono+R (shared between Component and Composite) (2) Input RCA/Mini-Din(4 pin) Composite Video(CVBS) +S-video Audio : RCA L/Mono+R (shared between S-Video and Composite) MONITOR Output RCA video ouput Audio out RCA(L+R) RGB/PC Input Mini D-sub 15 pin Analog RGB PC/HDMI1 Input Phone jacks Audio L+R (AUDIO) HDMI1 Input(type A) 19 pin A/V Digital HDMI2 Input(type A) 19 pin A/V Digit
Note 36
Note 37
Note 38
