Introduction Connecting your TV Using the Remote Control OWNER'S MANUAL Owner's Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. 34HFX84 34HFX84 Index Model: Appendix Using the TV’s Features Setting up your TV Color Television Serial No.
Dear Customer, Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV. Before operating the TV, please read this manual completely, and keep it nearby for future reference. Safety Precautions WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
Important Safety Instructions 1) 2) 3) 4) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
31) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time. 25) Always operate this equipment from a 120 VAC, 60 Hz power source only. 26) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).
Important Safety Information ............................. 2-4 Introduction ................................................................ 6 Welcome to Toshiba ......................................................... 6 Exploring your new TV ................................................... 6 Connecting your TV .................................................. 7 Connecting an antenna or cable TV ................................. 7 Connecting a VCR ......................................................
Introduction Introduction Welcome to Toshiba Connecting your TV Congratulations! You have purchased one of the finest projection TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible. Instructions in this manual are based on using the remote control. You can also use the controls on the TV if they have the same name as those on the remote control.
Introduction Connecting your TV Note: Cables are not supplied with your TV. Connecting an antenna or cable TV This connection allows you to watch TV programs or basic cable channels. From Antenna or Cable TV Connecting your TV Using the Remote Control ● S-video cable Component video cables HDMI cable NOTE: RISK OF EQUIPMENT DAMAGE. Do not plug in any power cords until you have finished connecting all equipment.
Introduction Connecting a VCR Connecting your TV This connection allows you to watch local channels and video programs, play or record on the VCR while watching TV, and record from one channel while watching another channel. You will need: • two coaxial cables • one set of standard A/V cables From Cable Box or Antenna Note: If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.
Introduction Connecting a cable converter box and VCR TV If you have a VCR with S-video, use an Svideo cable (in the S-video jacks) instead of a standard video cable. Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable. Connecting your TV From Cable Note: If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.
Introduction Connecting a DVD player or satellite receiver and a VCR Using the Remote Control Connecting your TV This connection allows you to watch DVD/satellite, VCR, and TV programs, and record one TV channel while watching another channel.
Introduction Connecting a DVD player with ColorStream® (component video) and a VCR Note: For the highest possible picture quality, use component video cables (or an HDMI cable) between the TV and DVD player. Connecting your TV You can connect the component video cables to either set of ColorStream jacks on the TV (HD1 or HD2). For HDMI connection, see page 14.
Introduction Connecting a DTV receiver/set-top box with ColorStream® (component video) and a VCR Setting up your TV Using the Remote Control Connecting your TV This connection allows you to watch DTV (digital TV), VCR, and TV programs, and record DTV and TV programs. Your TV has ColorStream (component video) inputs. Connecting your TV to a DTV receiver with component video can greatly enhance picture quality and realism.
Introduction Connecting two VCRs Do not connect the same VCR to the output and input jacks on the TV at the same time. To dub or edit, VCR 2 must select Line IN, and the TV must select VIDEO 1 (see “Selecting the antenna input” on page 25). From Antenna VCR1 IN IN from ANT OUT to TV * The Video OUT jack does not output the POP picture. OUT L VIDEO R AUDIO ** The Audio OUT jacks can output the sound of either the Main or POP picture (see “Selecting the Audio OUT sound” on page 57).
Introduction Connecting an HDMI or a DVI device to the HDMI input The HDMI[1] input on your TV receives digital audio and uncompressed digital video and audio from an HDMI device or uncompressed digital video from a DVI[2] device. Connecting your TV This input is designed to accept HDCP[3] program material in digital form from EIA/CEA-861/861B– compliant[4] consumer electronic devices (such as a settop box or DVD player with HDMI or DVI output).
Introduction Connecting an audio system Amplifier LINE IN L R TV Connecting your TV This connection allows you to use an audio amplifier and external speakers, and adjust the audio level using the TV’s remote control. To control the audio, turn on the TV and the stereo amplifier, and turn off the TV’s built-in speakers (see “Turning off the built-in speakers” on page 57).
Introduction Using the remote control Connecting your TV Your Toshiba TV remote control has one dedicated TV mode and five universal modes: VCR, Cable/SAT, DVD, Audio1, and Audio2. The target devices and default devices being programmed for each mode are as follows: Target device/Mode mapping Using the Remote Control Mode TV CABLE/SAT VCR DVD AUDIO1 AUDIO2 Device Toshiba TV Universal Cable, Satellite Universal VCR, DVD, LD, Cassette Universal DVD, VCR, LD, Cassette Universal Audio: Amp., Tuner, Misc.
Introduction Remote Control functional key chart Cassette (VCR) Connecting your TV --Power Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Using the Remote Control TV Setting up your TV Digit 7 Digit 8 Digit 9 ----Digit 0 ------------- Using the TV’s Features ------Volume up/down* ----- Appendix TV Sound mute* ------------Rewind Pause Play Fast FWD Index Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD (TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) LIGHT Lights the remote key, and toggles between
Introduction Key Label TV/VCR AM/FM DISC STOP REC** POP CH yz Toshiba TV Cable Satellite VCR (TV) (CBL/SAT) (CBL/SAT) VCR --TV/SAT TV/VCR --------- Using the Remote Control Connecting your TV VCR VCR VCR VCR POP channel up/down SPLIT POP Split POP DIRECT CH POP Direct ch FREEZE Still picture SWAP POP Swap CH SCAN POP Ch scan SOURCE POP Source TV Receiver CD/MD Cassette (AUDIO) (AUDIO) (VCR) ------Reverse Disc shift AM/FM Disc shift Deck side A/B switch Stop Stop --Stop Stop Record** ------Record** TV
Introduction Programming the remote control for use with your audio/video devices Connecting your TV • Some newer VCRs are capable of working on either of two remote codes.These VCRs have a switch labeled “VCR1/VCR2.
CABLE/SAT LIGHT SLEEP 1 2 3 4 5 6 7 8 9 VCR DVD AUDIO1 AUDIO2 MODE PIC SIZE ACTION MENU IDE GU S Introduction Connecting your TV POWER TV ET 0 FA V O R I T T IT L E UP SUB TITL E FAV ENT E THE LI N A T E R K AU DI ENTER FAV VOL Using the Remote Control DVD RTN CH RTN EXIT DVD CLEAR INPUT SLOW/DIR Setting up your TV Volume Locked to TV (default) CBL/SAT VCR DVD AUD1 AUD2 TV CBL/SAT VCR DVD TV CBL/SAT VCR DVD AUD1 AUD2 TV CBL/SAT VCR DVD AUD1 AUD2 TV CBL/SAT VCR DVD AU
Introduction Device code table Brand Code ABC ARCHER CABLEVIEW CITIZEN CURTIS DIAMOND EAGLE EASTERN GCBRAND GEMINI G.I.
Introduction Device code table CD Player setup codes Brand Using the TV’s Features Setting up your TV Using the Remote Control Connecting your TV ADMIRAL 6126 AIWA 6133, 6135 CARVER 6129 DENON 6142, 6151 EMERSON 6139 FISHER 6105, 6106 GARRARD 6117 HARMAN KARDON 6120, 6121, 6123, 6119 HITACHI 6107 JENSEN 6134 JVC 6140, 6141, 6145, 6148, 6151 KENWOOD 6100, 6101, 6111, 6145 LXI 6136 MAGNAVOX 6129, 6132 MARANTZ 6129 MCINTOSH 6121 NAKAMICHI 6110 ONKYO 6114, 6115 OPTIMUS 6108, 6118, 6120, 6122 PANASONIC 612
Introduction Learning about the remote control The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the “Remote Control functional key chart” on pages 17–18. POWER turns the TV on and off Connecting your TV SLEEP allows access to the automatic TV shut-off function (page 59) LIGHT The first press of the LIGHT button lights the keypad and turns on the Illumination mode.
Introduction Setting up your TV Learning about the menu system Using the Remote Control Connecting your TV After you have installed the batteries and programmed the remote control, you will need to set some preferences on the TV using the menu system. You can access the menu system using the buttons on your TV or the remote control. 1. Press MENU to display the menu system. 2. Press x or • to select a menu. 3. Press y or z to select an item, then press ENTER. 4.
Introduction Changing the on-screen display language You can choose from three different languages (English, French and Spanish) for the on-screen display of adjustment menus and messages. To select a language: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z to highlight LANGUAGE, and then press ENTER to display the pull-down menu.
Introduction Adding channels to the TV’s memory When you press Channel y or z, your TV will stop only on the channels stored in the TV’s channel memory. Follow the steps below and on the next page to program all active channels into the TV’s memory.
Introduction Adding and erasing channels manually After you have programmed the channels automatically, you can manually add or erase specific channels. To add or erase channels: 1. Select the channel you want to add or erase. If you are adding a channel, you must select the channel using the Channel Number buttons. 2. Press MENU, and then press x or • until the SET UP menu appears. 3. Press y or z to highlight ADD/ERASE, and then press ENTER to display the pull-down menu.
Introduction Using the TV’s features Connecting your TV Switching between two channels using Channel Return The Channel Return feature allows you to switch between two channels without entering an actual channel number each time. 1. Select the first channel (or video mode) you want to view. 2. Select a second channel using the Channel Number buttons (0–9, 100). 3. Press CH RTN. The previous channel will display.
Note: • The FAV zy buttons operate as MENU zy buttons when a menu is onscreen. • The favorite channel feature is not available in ANT2 mode. FAVOR I TE CH CH ––– I NPUT ––– ––– ––– ––– ––– ––– Introduction 3. Press ENTER to display the FAVORITE CH menu. CH INPUT will be highlighted.
Introduction POWER TV CABLE/SAT LIGHT SLEEP 1 2 3 4 5 6 VCR DVD AUDIO1 AUDIO2 MODE 7 PIC SIZE ACTION MENU S IDE GU ET 8 9 0 ENT FA V O R I T INFO T IT L E UP SUB TITL E FAV E THE LI N A T E R K AU DI ENTER CH LABEL I NG CH I NPUT LABEL CLEAR CUSTOM MENU ––– –––– Using the Remote Control 0–9 : SELECT Setting up your TV 4. Press the Channel Number buttons to select a channel you want to label. 5. Press z to highlight LABEL. 6.
: : : : : Introduction SLEEP 1 2 3 4 5 6 DVD AUDIO1 AUDIO2 Number MODE 9 ENT FA V O R I T INFO IDE GU ET 8 0 +10 100/ T IT L E UP SUB TITL E FAV E THE LI N A T E R K AU DI ENTER PIC SIZE MENU Connecting your TV 7 PIC SIZE ACTION MENU ENTER yzx • FAV VOL CH DVD RTN CH RTN EXIT DVD CLEAR INPUT SLOW/DIR MUTE SKIP/SEARCH RECALL Note: You also can change the picture size by selecting PICTURE SIZE in the PICTURE menu.
Introduction Connecting your TV Theater Wide 1 picture size (For 4:3 format program) • The picture is non-uniformly enlarged—the center of the picture remains close to its original proportion, but the left and right edges are stretched wider to fill the screen. • A small part of the picture at the top and bottom is hidden; however, this mode cannot be scrolled.
Introduction Scrolling the Theater Wide picture (Theater Wide 2 and 3 only) 1. Press PIC SIZE to select the Theater Wide 2 or 3 mode. 2. Press MENU, and then press x or • until PICTURE menu appears. 3. Press y or z to highlight PICTURE SCROLL.
Introduction Connecting your TV Using the AUTO ASPECT feature When the AUTO ASPECT feature is set to ON and the TV receives a 480i signal, the picture size is automatically selected (as described in the following table).
POP window ANT 1 MAIN POP 6 12 2. Select POP channels in the following two ways: • To change to a specific channel, press POP DIRECT CH. While “POP” is on the screen, press the Channel Number buttons (0-9 and 100). • To change to the next programmed channel, press POP CH zy. If the V-CHIP feature is active and you try to watch a TV program that exceeds your set rating limits, the program will be blocked (see “Using the V-CHIP menu” on page 39).
Introduction Switching the main and POP pictures Press SWAP while you are using the POP feature to switch the main and POP pictures. Note: Connecting your TV • If the POP program is not 480i format, it will not display in the main window when you press SWAP. Example: Press x Example: Press • • The VARIBLE AUDIO OUT jacks will switch with the speaker sound; however, the source of the regular AUDIO OUT jacks is determined by the AUDIO OUT menu settting (page 57).
Introduction Double-Window aspect ratio The Double-Window feature displays each picture according to its input signal aspect ratio, as illustrated below. Note: • The AUTO ASPECT feature (page 34) does not operate in double-window mode. • Aspect ratio is the ratio of width to height of the picture.
Introduction POWER TV CABLE/SAT SLEEP 1 2 3 4 5 6 7 8 9 0 ENT VCR DVD AUDIO1 AUDIO2 MODE PIC SIZE ACTION MENU IDE GU S Moving picture purple LIGHT ET +10 100/ FA V O R I T INFO T IT L E UP SUB TITL E FAV E THE LI N A T E R K AU DI O Connecting your TV Using the favorite channel search function You can use the favorite channel search function to quickly scan your favorite channels (see “Programming your favorite channels” on page 28). 1. Press FAVORITE.
Introduction Using the LOCKS menu Entering the PIN code 1. Press MENU, and then press x or • until the LOCKS menu appears. Note: The V-Chip function is available only for the U.S. V-Chip system. The Canadian V-Chip system is not supported. Connecting your TV The LOCKS menu includes the V-Chip, CH Lock, Video Lock, and New PIN Code functions. You can use these functions after entering the correct PIN code.
Introduction ENABLE BLOCKING 1. From the LOCKS menu, press z or y to highlight V-CHIP, and then press ENTER. The V-CHIP menu appears. 2. Press z or y to highlight ENABLE BLOCKING, and then press ENTER. Connecting your TV V – CH I P ENABLE BLOCK I NG TV RAT I NG MPAA RAT I NG BLOCK I NG OPT I ON LOCKS MENU : SELECT LOCKS menu LOCKS V - CH I P CH LOCK V I DEO LOCK NEW P I N CODE OFF ON OFF : MOVE ENTER : START E N T E R : SET 3. Press y or z to select ON or OFF.
MPAA RAT I NG X NC17 R PG13 PG MPAA RAT I NG V – CH I P MENU : MOVE X X G X : SELECT Introduction V-CHIP menu V – CH I P ENABLE BLOCK I NG TV RAT I NG MPAA RAT I NG BLOCK I NG OPT I ON LOCKS MENU : MOVE ON Connecting your TV MPAA RATING (Independent rating system for movies) 1. From the V-CHIP menu, press z or y to highlight MPAA RATING, and then press ENTER. The MPAA RATING menu appears. 2. Press y or z to highlight MPAA RATING. 3. Press • to lock (“X”) or press x to unlock (“✓”).
Introduction Unlocking programs temporarily 1. If you try to watch a TV program that exceeds the rating limits you set, the TV enters program lock mode. After 4 seconds, the TV starts the auto favorite channel search function (see page 38). You can either unlock the program temporarily (see steps 2-4) or select a non-locked program to watch.
12 33 ––– 18 ––– ––– CH 12 ––– ––– 28 ––– ––– TV CABLE 18 ––– ––– 33 ––– ––– TV CABLE CLEAR ALL LOCKS MENU CLEAR ALL LOCKS MENU : SELECT ––– I NPUT : SELECT ENTER : CLEAR CABLE/SAT LIGHT SLEEP 1 2 3 4 5 6 7 8 9 DVD AUDIO1 MODE PIC SIZE ACTION MENU S IDE GU ET +10 0 100/ FA V O R I T INFO T IT L E UP SUB TITL E FAV ENT E THE LI N A T E R K AU DI O 3. Repeat step 2 for other channels.
Introduction Locking the video inputs Using the Remote Control CABLE/SAT LIGHT SLEEP 1 2 3 4 5 6 VCR DVD AUDIO1 AUDIO2 MODE 7 PIC SIZE ACTION MENU IDE GU ET 8 9 0 ENT +10 100/ FA V O R I T INFO UP E SUB TITL E T IT L E FAV VOL : Unlocks all video input sources.
Introduction Adjusting the picture Picture Quality Sports Standard Movie Preference Bright and dynamic picture (factory setting) Standard picture setting (factory setting) Movie-like picture setting (factory setting) Your personal preferences* *(see “Saving your new preferences” on page 46) To select the picture mode: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press z or y to highlight MODE, and then press ENTER. 3.
Introduction Connecting your TV Saving your new preferences You can save the PICTURE qualities you adjusted (contrast, brightness, color, tint, sharpness, color temperature, CableClear DNR, and SVM) in the picture PREFERENCE mode. To save your new preferences: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight PICTURE SETTINGS, and then press ENTER. The PICTURE SETTINGS menu appears. 3. Press yzx • to highlight SAVE, and then press ENTER.
: MOVE Introduction ANTENNA SPORTS COOL OFF OFF Using the Remote Control P I CTURE SETT I NGS MODE COLOR TEMPERATURE SVM CableClear DNR P I CTURE MENU RESET Note: SVM is not required when viewing some high-quality video material. If you are watching high-quality video material, you may want to set SVM to OFF. Connecting your TV Selecting the Scan Velocity Modulation (SVM) The SVM feature enhances picture contrast and sharpness. This feature has three modes: HIGH, LOW, and OFF.
P I CTURE SETT I NGS MODE COLOR TEMPERATURE SVM CableClear DNR P I CTURE MENU DONE : MOVE ANTENNA SPORTS COOL H I GH AUTO SAVE ENTER : START Setting up your TV Selecting the display format (for 480p signals only) This feature converts 480p input signals to 540p or 1080i. To select the display format: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight DISPLAY FORMAT, and then press ENTER. 3. Press y or z to select 540p or 1080i, whichever you prefer.
Introduction Selecting the video input source SOURCE SELECT I ON ANT 1 V I DEO 1 V I DEO 2 V I DEO 3 ANT 1 V I DEO 1 V I DEO 2 V I DEO 3 HDM I 1 HDM I 2 ANT 2 HDM I 1 HDM I 2 ANT 2 Color Stream HD1 Color Stream HD2 Color Stream HD1 Color Stream HD2 0- 7 : TO SELECT Pressing INPUT on the remote control displays the current signal source (press INPUT again or 0-7 to change) TV / V I DEO : TO SELECT Pressing TV/VIDEO on the TV changes the current signal source Labeling the video input sources The
Introduction Using the closed caption feature Connecting your TV The closed caption feature has two options: • Captions—An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as “CC” in TV listings). • Text—An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations). To view captions or text: 1. Tune the TV to the desired program. 2.
Introduction Setting the ON timer POWER TV CABLE/SAT POWER LIGHT SLEEP 1 2 3 4 5 6 DVD AUDIO1 AUDIO2 7 PIC SIZE S IDE GU ET 8 9 0 ENT +10 100/ FA V O R I T INFO T IT L E UP SUB TITL E FAV E THE LI N A T E R K AU DI Connecting your TV ACTION MENU MENU ENTER yzx • FAV 10h30m VOL CH DVD RTN CH RTN EXIT DVD CLEAR INPUT SLOW/DIR MUTE SKIP/SEARCH RECALL Using the Remote Control CUSTOM 0–9 : SELECT Number MODE ENTER ON T I MER SLEEP T I MER CC FAVOR I TE CH CH LABEL
Introduction Setting the clock Connecting your TV To set the clock: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z to highlight CLOCK SET, and then press ENTER. 3. Press the Number buttons (0-9) to enter the correct time. The clock operates on a 24-hour cycle. 4. Press ENTER to start the clock. Note : If the TV’s power source is interrupted (the power cord is unplugged or a power failure occurs), the clock must be reset.
Introduction Adjusting the sound LIGHT CABLE/SAT SLEEP VCR DVD 1 2 3 4 5 6 AUDIO1 AUDIO2 7 AUDIO MTS AUDIO SETTINGS WOW SRS 3D FOCUS TruBass Dolby Virtual : SELECT STEREO SAP MONO E N T E R : SET You can leave your TV in STEREO mode because it will automatically output the type of sound being broadcast (stereo or monaural). The word “STEREO” or “SAP” displays in yellow in the menu when the TV receives the signal. If the stereo sound is noisy, select MONO to reduce the noise.
Introduction Note: • The Dolby Virtual and SRS 3D features cannot be on at the same time. POWER TV CABLE/SAT Setting up your TV Using the TV’s Features Appendix Index ________ * Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Introduction Connecting your TV Note: If the broadcast is monaural, the WOW SRS 3D surround sound effect will not work. Using the Remote Control Using the WOW™ surround sound feature WOW is a special combination of SRS Labs audio technologies that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer, and wider. WOW consists of three features: SRS 3D, FOCUS, and TruBass. To adjust the WOW features: 1.
CABLE/SAT LIGHT SLEEP 1 2 3 4 5 6 7 8 9 VCR DVD AUDIO1 AUDIO2 MODE PIC SIZE ACTION MENU IDE GU S Introduction Connecting your TV POWER TV ET +10 100/ ENT E SUB TITL E T IT L E UP 0 FA V O R I T INFO AU DI FAV ENTER yzx • RECALL SAVE POWER TV CABLE/SAT LIGHT SLEEP 1 2 3 4 5 6 7 8 9 VCR DVD AUDIO1 AUDIO2 MODE PIC SIZE ACTION MENU IDE GU ET +10 0 100/ FA V O R I T INFO T IT L E UP SUB TITL E FAV ENT E THE LI N A T E R K AU DI O S Using the Remote
Introduction Note: Make sure the volume control of your audio amplifier is set to a moderate listening level. POWER TV LIGHT CABLE/SAT SLEEP Connecting your TV Turning off the built-in speakers Use this feature to turn off the TV speakers when you connect an audio system (see “Connecting an audio system” on page 15). To turn off the built-in speakers: 1. Press MENU, then press x or • until the AUDIO menu appears. 2. Press y or z to highlight SPEAKERS, and then press ENTER. 3.
Introduction Connecting your TV Using the CYCLONE® sub-woofer system Toshiba’s CYCLONE® ABX (Acoustic Bass eXpansion) system provides dynamic acoustic reproduction in a self-enclosed bass-reflex sub-woofer system. To turn on the CYCLONE® sub-woofer system and adjust the CYCLONE level: 1. Press MENU, and then press x or • until the AUDIO menu appears. 2. Press y or z to highlight CYCLONE. 3. Press x or • to highlight ON.
Introduction Selecting the background of the menu display POWER TV CABLE/SAT LIGHT SLEEP 1 2 3 4 5 6 7 8 9 0 ENT VCR DVD AUDIO1 AUDIO2 MODE PIC SIZE S IDE GU ET FA V O R I T INFO T IT L E UP SUB TITL E FAV E THE LI N A T E R K AU DI ENTER Connecting your TV ACTION MENU +10 100/ O You can change the background of the menu display by selecting from two preset types: shaded and solid (gray). To select the background: 1.
Introduction Appendix Specifications Connecting your TV • Note: This model complies with the specifications listed below. Designs and specifications are subject to change without notice. This model may not be compatible with features and/or specifications that may be added in the future. WARNING: RISK OF ELECTRIC SHOCK ! Never attempt to service the TV yourself. Opening and removing the covers may expose you to dangerous voltage or other hazards.
Introduction Troubleshooting No sound, picture OK • The sound may be muted. Press VOLUME. • The station may have broadcast difficulties. Try another channel. • Check that the SPEAKERS function in AUDIO menu is set properly. Poor picture, sound OK • Check the antenna connections. • The station may have broadcast difficulties. Try another channel. • Adjust the PICTURE menu. Poor reception of broadcast channels • The station may have broadcast difficulties. Try another channel.
Introduction Limited United States Warranty for 27'' FST PURE® and All Larger Television Models Connecting your TV Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. PRODUCTS PURCHASED IN THE U.S.A.
Introduction Limited Canada Warranty for 32'' and Larger Television Models Limited Two (2) Year Warranty on Picture Tube* TCL further warrants the picture tube in this television against defects in materials or workmanship for a period of two (2) years after the date of original retail purchase.
Introduction Connecting your TV Index A OP A/V cables (standard) ......................................................... 7 ANT 1/2 ................................................................................... 25 Antenna cables (coaxial) ................................................... 7 AUDIO OUT sound, selecting ........................................ 57 Audio system connection ................................................. 15 Auto aspect ..................................................
HEAD OFFICE: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A. NATIONAL SERVICE DIVISION:1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A. HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400 SERVICE CENTERS: TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470-5400 MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766 VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C.