TOSHIBA
Dear Customer, Thank you for purchasing this Toshiba LCD TV. This manual will help you use the many exciting features of your new LCD TV. Before operating your LCD TV, please read this manual completely, and keep it nearby for future reference. Safety Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
Important Safety Instructions 1) 2) 3) 15) CAUTION: • To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure. • To prevent electric shock, match wide blade of plug to wide slot; fully insert. Read these instructions. 4) Keep these instructions. Heed all warnings. Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
23) 24) Always place the back of the television at least four (4) inches away from any vertical surface (such as a wall) to allow proper ventilation. Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse. 25) Never overload wall outlets and extension cords. 26) Always operate this equipment from a 120 VAC, 60 Hz power source only.
Choosinga location for your LCDTV To Display your LCDTV onthe included Pedestal Stand: Observe the following safety precautions: 1) Read and Follow the pedestal assembly instructions with the pedestal. (for 42XV540U only) included CAUTION: Before beginning pedestal assembly, carefully lay the front of the LCD Panel face down on a fiat, cushioned surface such as a quilt or blanket. Leave the bottom of the unit protruding over the edge of the surface and assemble the pedestal as indicated below.
m FCCDeclaration of ConformitV ComplianceStatement (Fart15): The following symptoms are technical limitations of LCD Display technology and are not an indication of malfunction; therefore, Toshiba is not responsible for perceived issues resulting from these symptoms. The Toshiba 42XV540U, 46XV540U, and 52XV540U Televisions comply with Part 15 of the FCC rules.
ImportantSafetyInstructions .......................................... 3 Installation,Care, andService ........................................ 3 Chapter1: Introduction ............................ g Features Overview your TV fiont TV back of your new TV ............................ of steps for installing, setting up, and using new TV .................................. and side panel controls and connections ........ panel connections .......................... Chapter2: ConnectingyourIV ..........
Chapter7: UsingtheTV'sadvanced features............. Using the advanced picture settings features ............ Using dynamic contrast ......................... Using the static gamma feature ................... Selecting the color temperature ................... Selecting the cinema mode (480i and 1080i signals)... Using the ClearFrame '_' feature ................... Using the Fihn Stabilization feature ............... Using CableClear _ digital noise reduction .......... Using MPEG noise reduction ........
Features of your new TV The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, LCD TV: • Integrated digital tuning (SVSB ATSC and QAM) eliminates the need for a separate digital converter set-top box (in most cases). • 1080p output resolution. • Four HDMI '_' digital, high-definition multimedia interfaces with 1080p input support (_ page 16).
TV front and side panel controls and connections Model 42XV540U is used in this manual for illustration purposes. TVfront Rightsidepanel POWER -D _8 --10 --11 12 1 Controlpanel Remote sensor-remote sensor. 5 ARROWS Ay• • -- When a menu is on-screen, these buttons function as up/down/left/right menu navigation buttons. 6 MENU (ENTER) -- Press to access the menu system (_ page 33). When a menu is on-screen, the MENU button on the TV's control panel functions as the ENTER button.
TV back panel connections For an explanation of cable types and connections, see pages 12-19. [,oO,%T>] HDMI IN TVback -- Haml 1 2 I 3_ Power cord Cable Strap r- OUT--1 ® ANT/C 5 6 7 8 DIGITAL AUDIO OUT-- Optical audio output in Dolby Digital or PCM (pulse-code modulation) format for connecting an external Dolby Digital decoder, amplifier, A/V receiver, or home theater system with optical audio input.
Overviewof cable types Cables can be purchased from most stores that sell audio/video devices. Before purchasing any cables, be sure of connector types required by your devices and the length of each cable. Coaxial (F-type) cable Coaxial (F-type) cable is used for connecting your antenna, cable TV service, and/or cable converter box to the ANT/ gABLE input on your TV. HDMrMcable (with HDMI Logo"HDmI") HDMI (High-Definition Multimedia Interface) cable is for use with devices with an HDMI output.
Connectinga VCR(or a VCRwith S-video) and antenna, Cable TV or Camcorder From Cable TV or antenna Camcorder From Cable TV Cable box TVupperbackpanel [ Ago'T°..... i S-video cable IN CH4_ CH3 i OUT Stereo VCR or Standard AA/cable _ / VIDEO2 inputs onTVrightsidepanel £oEol Audio cable I TVlowerbackpanel I ,| You will need: To view the antenna or Cable signal: Select the ANT/CABLE video input source on the TV.
inga DVD......... iorst VideO),a VCR,............... and a satellite receiver Your TV has two sets of ColorStream ® (component video) inputs.
Connectinga device to the IR OUT infrared terminal using the IR blaster cable for IR pass-through device control You can use the TV's IR OUT terminal (infrared passthrough) to remotely operate (through the TV) many infrared remote-controlled devices (such as Toshiba infrared remotecontrolled VCRs or DVD players) enclosed within an entertainment center or similar cabinet. Without the IR OUT connection, the device typically would need to be visible to operate it remotely.
ing anHDM to the HDMIinput 0r Dvi device * To select the video input source, press INPUT on the remote control (r_ page 21 ). To program the TV remote control to operate other devices, see Chapter 3. To connect The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.
REGZA-LINKconnection You can control the basic functions of connected audio/video devices using the TV's remote control if you connect a REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and operations, see pages 57 and 58. TV upperbackpanel I Audioreceiver TV rightside panel HDMI IN N N Playbackdevice (REGZA-LINK HD DVDplayer,etc.) .............. ......... I Playbackdevice (REGZA-LINK HDDVDplayer,etc.
Connectinga digital audio system The TV's DIGITAL AUDIO OUT terminal outputs a Dolby ®_ Digital u,u_ or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby <'_Digital decoder or other external audio system with optical audio input. You will need: • optical audio cable (Use an optical audio cable that has the larger "TosLink" connector and not the smaller "minioptical" connector.) Note: • Some audio systems may not be compatible with Do/by Digital bitstream signals.
Signal names for mini D-sub 15-pin connector 1 R 6 Ground 11 NC With either the PC IN or HDMI connection, you can watch your computer's display on the TV and hear the sound from the TV' s speakers.
Preparing the remote control for use Installing the remote control batteries Your TV remote control can operate your TV and many other devices such as cable converter boxes, satellite receivers, VCRs, DVD players, and HTIBs (home theater in a box), even if they are different brands. 1 Slide the battery cover off the back of the remote control. 2 Install two "AA" size alkaline If you have a Toshiba device: Your TV remote control is preprogrammed Toshiba devices (_ page 24).
MODE SELECT sets the five remote control device modes: TV, CABLE/SAT, HD DVD, DVD, and VCR/PVR. Press TV until the keypad blinks 3 times to control the TV. The selected MODE key blinks each time any key is pressed. (_' page 24). When the Auto Input feature is set, these keys can also be used to change inputs on the TV (_'_v'page 37). Learningabout the remote control The buttons used for operating the TV only are described here.
Remote Control functional key chart .... ti in!"'i iiiiii_iiii_iii1i!_{iiiiii1ii!i_iiii}_ii!iiiiii_iii1ii!!i!{!{ii!!iiiiiiiiiIi_iiiiiiiIi iiiiiiiii_{ii_i1i_iii1iiiiii{ii_iiiii!i!!!iii!i!!iiiiiii}_iiii_ii:_i_iiiiiiiii t¸¸I ................................................... K_i!lliiIiiiiiii/i!! ..... !!!_ (TV) Sleep ,,,,,,! ....... (TV) Sleep _i!i!i_i_!iiiiiiii_iili!iiiii!ii';iiii Remote control device .... !_,,,!!!i!!!_!,,,!i!,,i,,_,!,,!! _, ....
_E ii_iN!_ii_!iNi iiiii _I Last Channel Last Channel Last Channel DVD RTN DVD RTN DVD RTN DVD RTN Pause Cable Pause SAT Pause Pause/Step Pause Pause Pause Pause Pause Play Cable Play SAT Play Play Play Play Play Cable Stop SAT Stop Stop Stop Play Stop Play stop Stop Stop Stop SkipREW/ .................................................................................................................... Day- Skip REW Skip REW Skip REW Skip REW SkipFWD/ ................
Usingthe remote controlto operate your other devices Your TV remote control has one dedicated TV mode and four programmable multi-brand modes: CABLE/SAT, HD DVD, DVD, and VCR/PVR. The default device modes and programmable device modes are listed below. Note: The TV remote control is preprogrammed to operate most Toshiba devices. To operate a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you will need to program the remote control.
Searching and sampling the code of a Using the volume lock feature (8000) device(8500) By default (factory setting), tile remote control's volume keys (I;{__ and _) are locked to tile "TV" device mode. If you do not know tile device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device.
Multi-brand remote control device codes NSC 10012, 10017 10637 Pace 11877, 10237, 10877, 10008 Panasonic 10000, 10144, 10637 10008, 10107 Paragon 10000, 10525 10008, Penney Philips Pioneer 10000, 10637 11305, 10317 10877, 10533 tS"ism 11877, 10144, 10012 Pulsar 10000 Quasar RadioShack 10000 RCA 11256 Regal 10276, 10273 Oak Panther TVs Brand Code Toshiba 01524 Cable boxes DirecTV Dish Network Echostar 11505,11005, 10775,11170, 11775 Expressvu Fortec Star 10775,11775 11
Star Choice Star Trak Thomson Tivo Toshiba 10869 Daewoo 10772,10869 10392,10566 11142,11442 UltimateTV Ultrasat Uniden Voom Zenith 10749,11749, 10790,10819, 11285,11286, 11287,11289, 11857,11858 20784,20705, 20770,20833, 20869,21169, 21172,21234, 21242 Lenoxx 21127 LG 20591,2074l, 20801,20869 LiteOn 21058,21158, 21416,21440 Loewe Logix 20511,20741 20783 Magnasonic 20651,20675 Magnavox 20503,20539, 20646,20675, 20821,21268 Dansai 20770 Decca 20770 Denon Denver 20490,20634 20778 11392
Sampo Samsung 20698,20752 RCA 61769 Sony 20490,20573, 20744,20820, 20899,21044, 21075 Toshiba 61510,61515, 61769 20864,21033, 21070,21431 Sylvania 20675 Symphonic Toshiba 20675 Zenith 20741,20869 31593 31593 Sansui 20695 Sanyo 20670,20675, 20695,20873, 21334 Schneider Schwaiger Sensory Science Sharp Sharper hnage Sherwood Shinsonic Slim Art Sonic Blue 20783 20752 21158 20630,20675, 20752,21256 21117 DVD-R 20503,21854 Brand Code Accurian 21416 Emerson Funai 21056 Hitachi 30000
CCE 30072, 30278 30278 30035, 30240, 30209, 30479, 30037 30037, 30000, 30278, 31278 Colortyrne 30060, 30045, 30035, 30278 Colt 30000, 30072 Craig 30037, 30240, 30271 30047, 30072, Criterion 30000, 30072 Crosley 30035, 30000, Cineral Citizen Classic Crown Curtis Mathes Cybemex CyberPower Daewoo Gemini 30060 Genexxa 30037, 30278 30000, Go Video 30240, 30526, 30432, 30614 GoldStar 30035, 30039, 30278, 31237 30037, 30000, 30038, 30037, 30000, 30278, 30062 30081, 30072, 30020,
Orion Panama Panasonic Penney Pentax Philco Philips Pilot Pioneer Polk Audio Portland tS"esidian tS"ofitronic tS"oscan tS"otec tS"otech Pulsar Pulser Quarter 30184, 30000, 30121, 30002, 30208, 31479 30035 30240, 30104, 30209, 30278, 30479, Realistic 31062, 30162, 30020, 30614, 31035, 31262 30035, 30000, 30225, 30616, 31162, 30035, 30037, 30081, 30000, 30067, 31035, 30042, 30035, 30000, 30479 30035, 30048, 30045, 30209, 30616, 30739, 31181 30037 30162, 30047, 30240, 30042, 30038, 31237 30105 3008
Wharfedale 30593 White Westinghouse 30000, 30072, 30479 World XR1000 Yamaha Zenith ZTGroup Motorola 30209, 30278, 30209, 30479 30002, 30035, 30000, 30208 30240, 30072, 30041, 30038 30037, 30033, 30209, 30278, 31139, 31972 30039, 30000, 30041, 30479, 31479 11376,10810, 11187,11106 11822 Myrio Pace 11877,10237 Pioneer 11877,10877 11256 RCA Scientific Atlanta Sony Supercable Thomson Zenith Arcam 11256 Audio 10899 Burmester 50420 50157 California Audio Cambridge Soundworks Labs 500
Philips 50626,50157, 50274 Bose 41229,40639, 41253,41933 Pioneer 51062,50032, 51087,50468 50157 Cairn 40189 40531 PolkAudio tS"oceed tS"oton QED Quad Quasar RadioShack RCA Realistic Capetronic Carver 50420 50157 50157 50000,50032, 50087,50179, 50180,50420, 50468 Revox Rotel SAE Sansui 50157 Sanyo 50000,50087, 50179 Sears 50179 Sharp Sherwood Sonic Frontiers 50037,50180 50180 Sony 50490,50000, 50100,51364, 50185 50157 40189 41295,41304, 41500 Sansui 41189,40189 glnerson Fisher 40
Main menu layout Setup/Installation menu layout To open tile main menus (illustrated below), press _ remote control or TV control panel. Applications Video Audio Preferences Locks Setup on tile Channel Browser '_' Favorites Browser 42 42 REGZA-LINK Player Control Start Demo Mode 57 35 48 Picture Settings Noise Reduction ColorMaster 48 62 63 x.v.
Navigatingthe menusystem You can use the buttons on the remote control or TV control panel to access and navigate your TV's on-screen menu system. • Press _ to open the menu system. • When a menu is open, use the upldownlleftlright arrow buttons (AV
Setting the DemoMode Selectingthe menulanguage When you first turn on the TV, menu language selection and Demo Mode selection windows will appear by default. You can choose from three different languages (English, French and Spanish) for the on-screen display of menus and messages. To select settings: 1 2 To select the menu language: From the menu language selection window, select your preferred language. 1 2 Press _ 3 Press • or • to select your preferred menu language and press @.
Configuringthe input sourcefor the ANT/CABLEterminal To configure the ANT/CABLE input source: 1 Press _ and open the Setup menu. 2 Highlight Installation and press @. A new set of Installation menu icons will appear, as shown below. Programmingchannels into the TV's channel memory When you press (_ or _,_ on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV's channel memory. Follow the steps below to program channel memory.
3 Open the Terrestrial menu, highlight Channel Program to bring up tile Start, and press @ again to begin channel programming. To revert to your original settings: Highlight Cancel and press @ before saving. To remove all channels from the channel memory: Highlight Reset and press @, and then highlight Done and press @. To remove The TV will automatically cycle through all the channels, and store all active channels in the channel memory.
2 Press • or • to highlight Enable Auto Input and then press • or • to select On. 3 Press • and •• 4 Repeat steps 2 and 3 for other channels. 5 To save your settings, highlight Done and press @. to highlight No Label and press @. If the desired channel label is not available presets, you can create a custom label. from the list of To create and assign a custom label: Video 3 4 Press • or • 1 to select the mode field you want to set. Press • or • to select the desired input source mode.
tting t mode.......................................................................... Viewing the digital signal meter You can view the digital signal meter in the ANT/CABLE digital TV input source only. To set the HDMI audio mode: 1 2 From the Audio menu, highlight Audio Setup and press 0. To view the digital signal Press • or • to select HDMI 1 Audio and then press • or • to select the HDMI 1 audio mode (Auto, Digital, or Analog). (Auto is the recommended mode.
Viewing the systemstatus You can select either Power-Saving To view the system status: 1 From the Setup menu, highlight Installation and press @. A new set of Installation menu icons will appear. 2 Open the System Status menu, highlight System Information, and press @. 3 Press • • to scroll through the menu bar to select the Software Version and view the related information. To close the screen and return menu: Highlight Done and press @. To return Press _i_.
Selecting the video input source to view Note: • When selecting REGZA-L/NK input sources from the popup window using _), some REGZA-LINK devices may automatically turn on. • To select the video input source to view: 1 2 Press @ When selecting input sources using • V, you wifl have to press -@ to actually select a particular device from the popup window. on the remote control or TV control panel.
4 Press • or • to select the desired label for that input source. If a particular input is not used, you can select Hide as the label, which will cause that input to be "grayed out" in the Input Selection screen and skipped over when you press _ on the remote control. 5 To save the new input labels, highlight Done and press 0. To revert to the factory default labels, highlight Reset and press 0.
To set up the Channel Elements of the Channel Browser'" BrowserTM: 1 From the Preferences menu, highlight Channel Browser Setup and press @. 2 Press • to highlight Navigation, and then press • or • to select either Browse Mode or Select Mode. 1 2 , I 5 6 Current list (History, ANT/CABLE, Favorites, or REGZA-LINK) 3 Input type 3 Channel or input currently being viewed Press • to highlight History List, and then press • or • to select the setting you prefer: either On or Off.
Addingand clearing channels and inputs in the History List Adding channels and inputs to the History List: As a channel or input is tuned, the Channel Browser'" adds it to the History List and displays it on the "right side" of the Channel Browser '_'. Previously tuned channels/inputs are "shifted" to the left, eventually moving off the left side. Press i_ • to surf backward through the previously tuned channels/ inputs.
Switching between two channels using Channel Return The Channel Return feature allows you to switch between two channels without entering an actual channel number each time. 1 Select the first channel you want to view. 2 Select a second channel using the Channel Number buttons (and the dash ((_)) button if selecting a digital channel). 3 Press [_ on the remote control. The previous channel will display.
Natural 4:3 HD (for 720p, 1080i, and 1080p program sourcesonly) 000 000 000 000 Some program formats will display with sidebars and/or bars at the top and bottom. Picture is not distorted from original size. Native TheaterWide 1 (for 480i (HDMI), 480p (HDIVlI),720p, 1080i, and 1080p signal programs) (for 4:3 format programs) I O oo 1 [oo 1o The center of the picture remains close to its original proportion, but the left and right edges are stretched wider to fill the screen.
Scrolling the TheaterWide® picture (TheaterWide2 and3 only) You can set separate scroll settings for the TheaterWide 2 and TheaterWide 3 modes for each input.
Adjusting the picture quality Usingthe FREEZEfeature To use the FREEZE You can adjust tile picture quality (Contrast, Backlight, DynaLight TM, Brightness, Color, Tint, and Sharpness) to your personal preferences. feature: 1 When viewing the TV, press _ still picture. 2 To return to the moving picture, press _ to make the picture a again. Note: If the TV is left in FREEZE mode for more than 15 minutes, the FREEZE mode will automatically be released and the TV will return to moving picture.
Usingthe TheaterLock feature TM The TheaterLock'" feature allows you to "lock" all items that affect the picture mode setting. In other words, those settings that when adjusted cause the Mode setting to automatically change to "Preference" will be grayed out and unavailable when the TheaterLock setting is set to "On". Items that do not influence Mode status will not be affected e.g., Noise Reduction, x.v.Color Selection, Game Mode, etc.
Digital CC Settings To select closed captions: You can customize the closed caption display characteristics by changing the background color, opacity, text size, type, edge, and color. 1 Note: • This feature is available for digital channels only. • You cannot set the Caption Text and Background same color. as the Caption Size Auto, Small, Standard, Large Caption Text Type Auto, Default, Mono w. Serif, Prop. w. Serif. Mono w/o Serif, Prop.
Using the digital audio selector You can use the Digital Audio Selector to conveniently switch between audio tracks on a digital channel (for those channels that have multiple audio tracks). This temporarily overrides the audio track chosen by the language option under Audio Setup (_g:" "Selecting stereo/SAP broadcasts" below). To use the digital audio selector: 1 Press _ 2 Highlight Digital Audio Selector _:Advanced Audio 3 4 and open the Audio menu. Audio and press 9.
Using the StableSound® feature Tile StableSound ('_feature limits tile highest volume level to prevent extreme changes in volume when the signal source changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial). To turn on the StableSound This dynamic range control feature causes the ATSC dynamic range to be further compressed, allowing you to switch from digital to analog broadcasts at the same dynamic range.
2 Press •, which displays the PIN code entry screen. • The Lock System screen (below) appears if a PIN code has not been stored. Press the Channel Number buttons to enter a new four-digit code, enter the code a second time to confirm, and press @. • The Locks/Active screen appears if the PIN code is already stored. Use the Number buttons to enter your four-digit code and press 9. If the wrong PIN code is entered, the message "Incorrect PIN code, please try again !" appears. Highlight Retry and press @.
Downloading an additional rating system for blocking TV programs and movies Independentrating systemfor broadcasters Mature Audience Only (This program is specifically In the future, an additional rating system may become available for use in selectively blocking programs. designed to be viewed by adults and therefore may be unsuitable for children under 17.
Blocking channels Using the input lock feature With tile Channels Block feature, you can block specific channels. You will not be able to tune blocked channels unless you unlock them. You can use tile Input Lock feature to lock tile video inputs (Video 1, Video 2, ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, HDMI 4, and PC) and channels 3 and 4. You will not be able to view tile input sources or channels until you unlock the inputs.
To deactivate has activated the Input Lock once the GameTimer it: Set the Input Lock to Off (_ as described above). Usingthe PC settings feature "Using the input lock feature" You can view an image from a PC on the TV screen. Note: • A message will appear when 10 minutes, 3 minutes, and 1 minute remain or?the GameTimer.
Setting the PCAudio UsingREGZA-LINK This function allows you to output or mute the sound from your PC when connecting using the PC IN terminal and an analog RGB cable. This is a new feature that uses CEC technology and allows you to control Toshiba REGZA-LINK compatible devices from the TV remote via HDMI connection (_g:"page 17). When the Enable REGZA-LINK in the REGZA-LINK Setup menu (_g:"page 58) is set to On, the following REGZA-LINK functions will be enabled.
REGZA-LINK Player Control menu functions: 1 2 Press _ 3 Press • or • to select the item you want to control and press @. and open the THINC Applications menu. Highlight REGZA-LINK Player Control and press @. Power Turns the select device on and off. Top Menu Accesses the top menu of a DVD. Menu Accesses the menu of a DVD. Contents Menu Accesses the contents list when you press @. At this time, the REGZA-LINK Player Control menu will disappear.
To set the REGZA-LINK 1 Setup: From the Setup menu, highlight REGZA-LINK Setup and press @. 2 Press • or • to highlight Enable REGZA-LINK. 3 Press • or • to select On. Note: if you set Enable REGZA-LINK to Off, the other items wi// be grayed out.
DisplayingTV status information To display TV status information Press @ on the remote control. using RECALL: The following information will display (if applicable): • Current input (ANT/CABLE, Video 1, etc.) • If ANT/CABLE is the current input, either "CABLE" (for cable TV) or "ANT" (for over-the-air broadcasts).
Usingthe advancedpicture settings features 4 To revert the factory press _._. To select dynamic contrast preferences: 1 Press _ 2 Highlight Picture Settings and press @. highlight defaults, Done highlight and press @. Reset and Note: If you select one of #_e factory-set picture modes (Sports, Standard, Movie or PC) and then change the static gamma setting, the picture mode automatically changes to Preference.
Selecting the cinema mode (480i and 1080i signals) Using the Film Stabilization feature When you view a DVD (3:2 pulldown processed) from a DVD player connected to the Video 1, Video 2, ColorStream HD1, ColorStream HD2 (component video), or HDMI inputs on the TV, smoother motion can be obtained by setting the Cinema Mode to Film. To set the Cinema To turn on Film Stabilization: 1 From the Video menu, highlight Picture Settings and press @.
Using MPEG noise reduction Using Color Palette Adjustment The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. Choices for MPEG noise reduction are Off, Low, Middle, and High. Off is automatically selected when this feature is disabled ("grayed out"). When color palette adjustment is selected, tile list of base colors will be displayed. You can select a base color to adjust.
Using x.v.Color Selection feature The color range "x.v.Color" is an international enables a wider color range than conventional applications. When set to Auto, picture settings an x.v.Color signal is detected. standard video are automatically and set when Using the surround sound features When set to On, x.v.Color detection does not occur, so picture settings are always adjusted for x.v.Color. When set to Off, normal processing occurs. Note: If a non-HDMI input is selected or the x.v.
General troubleshooting Before calling a service technician, please check this chapter for a possible cause of the problem and some solutions you can try. Black box on-screen • The closed caption feature is setto oneof the Text modes (T1, T2, T3, or T4). Set the closed caption feature to Off (_ page 49).
Remote control problems Make sure the remote control is set to the correct device mode (_ page 21). Removeall obstructions betweenthe remote control and the TV. The remote control batteries may be dead. Replacethe batteries (_ page 20). Your TV remote control may not operate certain features on your external device. Refer to the owner's manualfor your other device to determine itsavailable features.
LEDindications The green and yellow LED lights on the TV front indicate TV's status, as described below. the Note: If the TV Ioses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow LED will brink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction. TV front POWER Yellow LED Green LED LED Indication • Green is ON (solid) The TV is operating properly.
FIXED AUDIO OUTPUT: 150 mv (rms) (30% modulation or less) Specifications Note: * This model complies with the specifications below. * Designs and specifications without notice. listed are subject to change * This model may not be compatible with features and/or specifications that may be added in the future.
Acceptable signal formats for PC IN and HDMI terminals PC IN signal formats Note: Depending on the connected PC, the following status may occur, incorrect failure, blur, or judder. But this is not a malfunction of your TV. VGA 59.940Hz 31.469kHz 25.175MHz 72.809Hz 37.861kHz 31.500MHz 75.000Hz 37.500kHz 31.500MHz 60.317Hz 37.879kHz 40.000MHz 72.188Hz 48.077kHz 50.000MHz 75.000Hz 46.875kHz 49.500MHz 60.004Hz 48.363kHz 65.000MHz 70.069Hz 56.476kHz 75.000MHz 75.029Hz 60.023kHz 78.
Limited United States Warranty for LCDTelevisions 26" and Larger Toshiba America Consumer Products, L.LC. CTACP") makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. LCD TELEVISIONS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A.
Limited CanadianWarranty for Toshiba Brand Flat Panel Televisions Toshiba of Canada Limited ("TCL") makes the following limited warranties to original consumers in Canada. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS TOSHIBA BRAND FLAT PANEL TELEVISION (the "-i-ELEVlSlON(S)" or "Television(s)") AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
Disclaimer and Limitation of Remedy TO THE EXTENT NOT PRECLUDED BY LAW, ALL OTHER EXPRESS AND IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS FOR THIS TELEVISION, INCLUDING THE IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED AND EXCLUDED.
A F P Film Stabilization ............................ 62 PC Audio ........................................ 57 Audio quality adjustments ............... 51 FREEZE ......................................... 48 PC connection ................................ 19 Audio system connection ................ Auto aspect .................................... 18 47 6 PC settings ..................................... Picture mode .................................. 56 48 Auto Input .........................
TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C. CorporateHeadquarters:82TOTOWAROAD,WAYNE,NJ07470,U.S.A. NATIONAL SERVICE DIVISION:1420-BTOSHIBADRIVE,LEBANON, TN37087,U.S.A. TOSHIBA OF CANADA LTD. HEADOFFICE:191McNABBSTREET, MARKHAM, ONTARIO,L3R8H2,CANADA- TEL:(905)470-5400 SERVICE CENTERS: TORONTO: 191McNABBSTREET, MARKHAM, ONTARIOL3R8H2,CANADA-TEL:(905)470-5400 MONTREAL: 18050TRANSCANADA,KIRKLAND,QUEBEC,H9J4A1,CANADA-TEL:(514)390-7766 VANCOUVER: 13551COMMERCE PARKWAY, SUITE110,RICHMOND, B.C.
