40 46 55G300U EN-A5--Cover-03.pdf ] 2010/3/10 I-_ 10:24:04 _;÷ TOSHIBA Leading Innovation _>)) Foran overviewof stepsfor settingup your newTV, see Note:Todisplaya HighDefinitionpicture,the TVmust bereceMng a HighDefinitionsignal(suchas anover-the:airHigh Definition TV broadcast,a High Definitiondigitalcableprogram,or a High DefinitiondigitaLsatellite program).FordetaiB,pleasecontact cable provider.
Dear Customer_ Thank you for purchasing this Toshiba LCD TV. This manual will help you use the many exciting features of your new LCD TV. Before operating your LCD TV, please read this manual completely,and keep it nearbyfor future reference.
brokenglassor liquidfrom thedamagedtelevision. TheLCDpanelinsidethe TVcontainsglassandatoxic liquid. Ifthe liquidcomesin contactwith yourmouth or eyes,or your skinis cut bybrokenglass,rinsethe affectedareathoroughlywithwater andconsultyour doctor. importantSafety instructions 1) Read these instrnctions. 2) 3) 4) Keep these instructions. Heed aiiwarnings. Follow all instructions. 5) Do not use this apparatus near water. 6) Clean onlywith dry cloth. 7) Do not block any ventilationopenings.
24) To avoid damageto this product, neverplaceor store the TV in direct sunlight; hot, humid areas;or areas 33) . Use extreme care to make sure you are never in a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits. 25) Always placethe TV on the floor or a sturdy, level, stablesurfacethat can supportthe weight of the unit.
40) During normal use, the TV may make occasional snapping or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.
46" TV 7) VESAMounting Pattern VESA 40" 200x200 mm M6 46" 400x200 mm M8 55" 400x200 mm Mounting Pattern M8 (mlit in ram) Removing the Pedestal Stand 1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface. Four Note; Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.
FCCDeclarationof Conformity Important notes aOout Vour Comp#ance StatementtPart15): £80 7g The Toshiba40G300U, 40G30U, 46G300U, 46G30U, and55G300U Televisions comply with Part 15 of the FCC rules.
importantSafety instructions ............................... Installation,Care, and Service ............................. 3 3 Chapter1: introduction...................................... g Features ol your new TV ................................................................ Overview of steps Jill" installing, setting up, and using your new TV ......................................................... 10 TV lront and side panel controls and connections .......................
Features of your new TV The following features are just a few of the many of your new Toshiba HD, LCD integrated TV: * Integrated QAM) e×citing widescreen, digital tuning eliminates (SVSB ATSC and the need for a separate digital converter set-top box (in most cases). * 1080p output resolution. . Four HDMI' digital, high-definition multimedia interfaces 1080p input support (_:_ page 16). . HDMI new capability INSTAPORT '_' technology switching HDMI sources. .
Overview of steps for installing, setting up, and using your new TV 10 See "Menu layout and navigation" for a quick overview of navigating the TV's menu system (_:_ page 28). 11 Program Follow these steps to set up your TV and begin using its many exciting features. Carefully read the important safety, care, and service information. for future reference. 2 Observe the following for the TV: ,, Read "Important (_:_ page 7).
TV front and side panel controls and connections Model 40G300U is used in this manual for illustration purposes. Left side panel TV front TVtop 2 1 Control panel 1 Power LED(Green) TOSHIBA 2 Remote Logo -- range" POWER -- VOLUNE._1_ -volume 9 control (_v "Remote buttons adjust the iNPUT-- Repeatedly press to change the source yon are viewing (ANT/CABLE, VIDEO 1, VIDEO 2, ColorStreamHD,HgiVll1, HgiVll2, HglVll3, HDNI4, PC). control 21 ). to turn the TV oil and off. These level.
TV back panel connections For an explanation of cable types and connections, see pages 13-20. 1 TVback 2 PC IN HDMI iN '@IQI 4 PowerCord 5 I I I 8 1 LANIN -- LAN port your home 2 PC IN -- is used to connect the TV to network. For use when connecting a personal HDNF IN-- High-Definition Multimedia Interface input receives digital audio and uncompressed digital video from an HDM[ device or uncompressed digital DVI device. HDM[ connection receive 4 5 1080p a to signals.
Optical audio cable Overview of cable types CaNes can be purchased from most stores that sell audio/ video devices. Bef%re purchasing any cables, be sure of Optical connector types required of each cable. audio inputto the TV's DIGITAL AUDIOOUTterminal by your devices and the length Dolby audio cable is fur connecting Digital or PCM (pulse-code receivers modulation) with optical (L_¢page 187.
Connectinga VCRand antenna, Cable TV or Camcorder TVbackpanel From CaMe TV or FromCableTV antenna C_ ! 1 VIDEO2 inputs on TV right side panel You will need: To view the VCR: ., coaxial cables ., standardA/V cables Turn ON the VCR. Select the VIDEO1 video input source on the TV.
ConflecUflg a DVD player with ColorStream ® (component video), a VCR, arid a sateJJJte receiver From antenna TV back panel Satellite receiver with componentvideo or DVD player with componentvideo You will need: To view antenna • coaxial cables • standardA/V cables If you have a mono YCR, connect L/MONO on the TV to your VCR's audio out terminal using the white audio cable only Select the ANT/CABLE video input source on the TV.
Connecting aft HDNI ® or DVI device to the HDN] input The HDM[ input on your TV receives digital audio and uncompressed digital video from an HDM[ source device, or macompressed digital video from a DVI (Digital Visual Interface) source device. This input is designed to accept HDCP (HighBandwidth Digital-Content Protection) wogram material in digital form from ElA/CEA-861-Dcompliant m consumer electronic devices (such as a set-top box or DVD player with HDM[ or DVI output).
RERZA-LINK®connection You can control the basic functions of connected audio/video devices using the TV's remote control if you connect a REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and operations, see page 56. evice Playbackdevice (REGZA-LIRR DVDplayer, etc.) To connect an Audio Receiver and Playback Devices, you will need: ,, HDM[ cables (_:_ page 13) Note: ,, [f several devices are connected, REGZA-LINK feature may not operate properly.
Connectinga digital audio system The TV's DiGiTAL AUDIO OUT terminal outputs a *Dolby _ Digital or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby °_'Digital decoder or other external audio system with optical audio input. You will need: No te: o Some audio systems may not be compatible with Dolby Digital bitstream signals.
No te: No te: • • • The PC audio input terminals on the TVare shared with the HDMI- 1 analog audio input terminals (_,,_ page 50). • Some PC models cannot be connected to this TX • An adapter is not needed for corrputers with a compatible mini D-sub 15-pin terminal. Depending on the DVD's title and the specifications of the PC on which you are playing the DVD-Video, some scenes may be skipped or you may not be able to pause during multi-angle scenes.
Toconnectthe TV to a home network the hackofyour TV I Router with Hub Modern(DSLorCahle} _ _ [] [] ........... [2113] Sever PC(with DLNA server function) [1] CoaxiaJ or teJephone cabJe (depending on your modem type) [2] Standard LAN cabJe [3] Do NOT connect a phone jack directJy to the TV's LAN port.
Preparing the remote control for use o If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones. o Your TV remote control can operate your TV and many other devices such as cable converter boxes, satellite receivers, VCRs, DVD players, and HTIBs (home theater in a box), even if they are different brands. If you have a Toshiba device: Your TV remote control is preprogrammed most Toshiba devices (_x"page 23).
Learning about the remote controJ The buttons used for operating the TV only are described here. For a complete list of the remote control's functions, see the remote control fmactional key chart (_:_vpage 24), 1 POWER turns the TV on and off. When the TV is on, the green LED indicator illuminated. 2 on the TV front will be FREEZEfreezes the picture. Press again to restore the moving picture (r,,vpage 42). 3 SLEEP accesses the sleep timer (_; page 56).
Usin9the remote controlto controlyourother devices If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you must first program the remote control to recognize the device (if you have not already done so) (r,; pages 25-27). 1 POWER Turns the selected device on and off. 2 channels Point the remote directly control at the device. (as opposed to _ to directly access {._.J). 3 +10 Press to directly access DVD chapters higher than 10.
Remote Control funcUonaJ key chart No te: o "---" = key does not send a signal in that remote control mode. o "_--TV" = key will affect the TV, even though the remote control is in another mode. o * Not available for your TV Power Power Power Power Power Sleep timer Picture size *-- TV _ TV _-- TV _ TV *-- TV _ TV *-- TV _ TV FREEZE _ _ _ _ Digit 1-9 Digit 1-9 Digit 1-9 Digit 1-9 Digit 1-9 Digit 0 - (sub CH) TV/Video select Digit 0 ....
Record (2 click) REC MENU* SLOW REW* SLOW FWD* Angle* Sub title* ----- DVD Angle DVD Sub title Audio* --- DVD Audio Eject* --- DVD Eject Programmingthe remote control to controlyourother devices Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote control to operate a non-Toshiba device (or a Toshiba device that it is not F_reprogrammed to operate), follow the steps below.
Remote control codes Expl_ss Vu F@tsu GE (157 (127 (108,009, 013 Clarion 019 Classic Daewoo (120 (12l In some be General 010, 01 l, 012,022, with Instruments Hitachi (123, 03 l, 049 (133 Denon Emerson Fisher (122,023,024, (126,027 (128 Hughes Hughes Network (133 Systems Intersat Janeil 019 048 027 Funai GE Go Video (127 001,029. 087 GPX 031 Cable converterbox JVC 017. Kenwood 029 ABC 061,062, (163, (}82,084, Hitachi WC Kenwood Konka (105,032, 033, (t34, (135 (}03, 0(}7,036.
Curtis Mathes 001,1105, 0119, 012, 01& 1140,1148, 053,056, 057 Daewoo011, (}13,015,017,018, Orion 054, 05Z 062,065,068, Video Concepts 072 036, (}45, 04& 057,061, 005,1106, 011,012,039, 053 Panasonic Wards 009, 010, 011,016, 1119, 05Z 078 Daytron Denon Dilnensia 1178 (}63 001, (}48 Electrohome Emerson 010,020,065 003,1108, 010, 01 I, 017_ 018,020,028,039,1154, 057,1162, 065,068,1172 Fisher 007, 016, 02 l, 022,1123, 1157, 06& 068, 0711, 07k 079 Fuji Funai 004, 041 018, 073 Garrard GE 018 00
Main menu Jayout The tables below and oll the next page provide a quick overview of your TV's menu system. MENU To open the main menus (illustrated below), press Picture Mode + Picture Settings .......................................... Noise Reduction Souud Preferences Locks on the remote control or TV control panel.
Setup/Installation menu layout The Installation To open the menu contains Installation Setup menu, select the Terrestrial Status menus.
initial Setup TOSHIBALogo LED When you first turn on or reset the TV, the Initial Setup window will appear. You can select TOSHIBALogo LEDeither On or Off. 1 [)1the Menu Languagefield, Press MENU O and open the Setup menu, highlight Logo LED. press 4 or _ to EXIT select your preferred language. 2 Press "9 or _ to select either On or 0l{ and press O • Press 4 or _ to select Time Zone and set your desired time zone with 4 or _ and press @_.
Programmingchannelsinto the TV's channel memory (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrialmenu, highlightChannelProgramto bring up the Start When you press (_ or _c,_,j on the remote control Scan, and press @ programming. again to begin channel or TV control panel, your TV will stop only on the channels you programmed into the TV's channel memory. Follow the steps below to program channels into the TV's channel memory.
3 Press A or V to select skipped box.To and press 0. remove To add a channel position to be A tick will appear a channel in the the tick, press @ to the channel again. memory: Highlight the checked box next to the channel number The maximum number of labels that can be stored is 128. To remove 1 2 Open the Channel Labeling window. you want to add, and then press @ to remove the tick.
the HDMI 1 Audio setting changes to "Auto." if PC Audio is set to "Yes," the HDMI 1 Audio setting is set to "Digital" and is grayed out in the menu. (Also see item 4 on page 12 and "Setting the PC Audio" on page 50.) Viewing the digital signal meter 4' Done and press @ Highlight and go back to the Channel to save changes, Labeling window. You can view the digital signal meter in the ANT/ CABLE digital TV input source only.
After the time zone has been set, you will be asked set the current Daylight Saving Time to status. To set the Daylight Saving Time status: 1 Press 4 or _ to select Yes or No, highlight [}one, and then press @. Viewing the system status To view the system status: MENU I Press O and open the 2 Highlight 3 A new set of Installation Setupmenu. Installati0nand press @. menu System Status menu, Inf0rmati0., and press @. 4.
Press @ Selecting the video input source to view To select the video 1 Press _) panel. 2 And then either: input source EXIT Note: ° When selecting REGZA-L/NK input sources from the popup window using _, some REGZA -L INK de vices may automa tically turn to view: on the remote control or TV control on.
3 Press at or V to highlight the video source yon want to label. Tuning channels Tuningchannelsusingthe ChanneJ Browser TM The Channel Browser TM provides an easy navigation interface for all your channels and inputs. This feature allows you to: 4 Press 4 or _" to select the desired label for that input source.
Elementsof the ChannelBrowser TM 1 2 3 4 I 5 3 Press Y to highlight History List, and then press 4 or _ to select the setting you prefer: Off. either On, or 6 1 Current list (History, ART/CABLE,inputs, Favorites, or REGZA-LIRK) 2 Input type 3 Channel or input currently being viewed Note: History List will be cleared every time the TV is powered off. 4. Press Y to highlight ART/CABLEList, and then press 4 or _" to select On or Off.
To tulle to a channel or input _ACK ] While watching TV, press _ in Select mode: '_ or _ t_ to open the Channel Browser TM and surf back to a previous or tbrward to the next item in the list. In Select mode, Channel Press @ item you stop on an item in the Browser rlx[, it will be highlighted must press @ item.
Tuningto the next programmed channel Switchingbetween two channels usingSurfLockTM To tune Press (_ panel. The SurfLock to the next programmed OH or _T_3on the remote control channel: or TV control channel channel OH RTN Note: This feature will not work unless you program channels into the TV's channel memory (_, page 31). O 1 TM feature OH FITN to the quickly temporarily .
To select the picture size using the menus: 1 Select Picture Size in the Theater Settings menu. 2 Press 4 or _ to select the desired picture size setting. 3 Highlight [}one and press @. Note: Some of the picture sizes may not be available depending on the receiving signal format (those will be "grayed out" in the Picture Size screen). Using these functions to change the picture size (i.e.
To set the scroll Press Native {for 480i {HDIVil),4SOp{HDiVil),720p, 1080i, and 1080p signal programs) settings: O and open the MENU Highlight Picture menu. Theater Settings arid press _. i©©© 000 ® If receiving a 480i (HDMI), 480p (HDMI), 720p, 1080i, or 1080p signal program, Native mode scales the video to display the entire picture within the borders of the screen (i.e. no overscanning). ,, This is especially useful for external HD sources such as DVHS movies, or PC graphics.
To turn on the auto aspect MENU 1 Press 2 Highlight 3 O and open ratio To save the new settings, @. To revert Reset press select highlight to the factory the picture mode using the menu system: MENU O @. Press 0u. Highlight and open M0de aim the Picturememt. press @. [}one and press defaults, highlight and press @. To turn Select To select Picturemenu. the TheaterSettings and [n the AUtO Aspect Ratio field, 4.
Adjusting the picture quaIRy Using the closed caption mode You can adjust the picture quality (Contrast, Backlight, DynaLight TM, Brightness, Color, Sharpness) to your personal preferences.
change to another analog channel, the closed caption DigRalCCSetUngs setting will automatically change back to the current You can customize the closed caption display characteristics by changing the background color, opacity, text size, type, edge, and color. Note: o This feature is avai/ab/e for digita/channe/s onl_ ° You cannot set the Caption Text and Background as the same colon To customize MENU You can also use the CCSe[ect0r to select digital closed caption services (if available).
3 Press & or V to select Audio, and then press 4 or _" to select the desired service. 4 Press G. EXIT second audio program. If you have SAP on, you will see the current program on the screen but hear the other language instead of the program's normal audio. ° If you have SAP on and the station you are watching is not broadcasting a second audio program, the station's normal audio will be outpuL However, occasionally there is no sound at all in SAP mode.
Using the Doihy® DigRal Dynamic Range Control feature PIN code has not been stored. Press the Channel This dynamic range control feature causes the ATSC dynamic range to be further compressed, allowing you to switch from ATSC to analog broadcasts at the same dynamic range. press @. Number buttons to enter a new four-digit code, enter the code a second time to confirm, and To use tile Dolby Digital Dynamic Range Control: MENU I Press 2 Highlight O 3 [n the DoJby Digital the Sound menu. @.
dialog, language). The V-Chip feature in this TV detects the signals and blocks the programs according to the ratings you select. (For rating descriptions, see the tables on the next page.) To block and unblock TV programs and movies: 1 Press 2 Press 3 MENU . O and h@ahght . V to display Enter your the Locksmenu the PIN code entering four-digit 4 Press V to highlight 5 Press _ to select To download system Locksmenu Press V to display Enter your four-digit PIN code and press @.
P6 Parental Guidance Suggested (Some material may not be suitable for children) O General Audience for all ages) Independent rating systemfor broadcasters TV-IVIA Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for children under 17.
Unlockingprogramstemporarily Usingthe GameTimer ® If you try to rune the TV to a program that exceeds the rating limits you set, the TV will enter program lock mode and the following message will aF_pear onscreen: You can use the GameTimer To set the You can either temporarily select an unlocked program unlock the program to watch. To temporarily the unlock 1 or Press 2 Enter program: 3 O. your four-digit the correct is released locking PIN code and press @.
5 Press _ to select On. When the control panel is locked and any button o13the control panel (except POWER) is pressed, the message "NOT AVAILABLE" appears. Note: The screen is disrupted momentarily when adjusting the PC settings. This is not a sign of malfunction. !i i!ii !i! i i!i!!! i iiii iii!iiiiiii!iiiii !iii ii i ;ii To unlock the control panel: Select 0fl in step 5 above, or press and hold the VOLUME- button on the TV control panel for about 10 seconds until the volume icon appears.
is set to "No," the HDM! 1 Audio setting changes to "Auto."/f PC Audio is set to "Yes," the NDM! 1 Audio setting is set to "Digital" and is grayed out in the menu. (Also see item 4 on page 12 and "Setting the HDMI ® Audio mode" on page 33.) Usingthe Media Player Usingthe Media Playerwith USB You can enjoy photos or music contents stored on a USB storage device. Photo Viewer specitications: Data type: JPEG Exif vet2.
Viewing photoflies ] To start slideshow, press @ ill the Single View mode. There are three types of view modes. Multi Press 4 / _ to view the previous/next photo. View: This view allows you to search for photos in a grid format. These pictures are displayed using thumbnail data in each image file. To set Interval Time and Repeat settings: the Quick Menu. Press MENU (3 Press & or V to select to open either IntervalTimeor Repeal.
Maximum Maximum Maximmn Best photo Duringplayback PAUSE/STEP Press to pause. _ PLAY * To resume nomml playback, press (_. SKIP , To locate a specific file, press _ * To adjust volume, press _ Note: SKIP or _ repeatedly. / v_ During playback, you can adjust the SOUND menu functions from the QUICK menu. To set tile repeat mode: MENU 1 2 Press 0 to open the Quick Menu. Press 4 o1:_ to select Off, All or 1.
Viewing movie _es You can select movies from a list of available files. Photo Photo list (Multi view) See page 52. Sorting (Only OSB storage device) To sort the lblders and files Press MENU O to open the from Multi View mode. 2 3 OuickMenu Press A or V to select Sort. Press "q or _ to select or OJd to set the sorting 1 2 Press A V to select a file or folder. (_ / [cT_Jbuttons can be used to page up/down the movie list when there are more files than will fit onto one screen.
Movie Movie list (Multi view) See page 54. Music Music list (Multi view) See page 52. Sorting (0nly USB storage device) Sorting(0nlyUSB storage device) To sort tile tblders and files To sort file tblders and files MENU I Press O to open the OuickMenu in the movie list mode. 2 Press A or V to select Sort. 3 Press 4 or _ to select Title,New or 0[d to set the sorting rule. Press O to open the QuickiVlenu.
Auto Setup 1 To set the menus: sleep timer using the on-screen Press M_U and 4 or _ to select the Setup menu. Press Press Retwork Setup then A or V to highlight Highlight press EN@. 3 Press 4 V to highlight or _ MENU (3 to select Auto Setup, and then press and open 3 Press the Number time in 10-minute 4. Highlight 0u (default). Note: sleep the Setup menu. Sleep Timer and press @. buttons to enter increments. the length [}oRe and press @.
FF REGZA-LINR ® inputsourceselection Fast-forwaMs. FlEW (_g) Rewinds/reverses. AV4_ Navigate contents menu, etc. @ Enters contents menu, etc. EXiT (3 Returns to the previous menu. Note: These functions depend connected. REGZA-LINK functions: 1 MENU 0 Press ®Player on the devices Control If a REGZA-LINK device with HDM[ switching capability (e.g.
From this item, you can set your audio output preference to the TV speakers or the audio receiver speakers. When this item is set toAudio Receiver. the TV remote can be used to adjust or mute the volmne of the audio. This item will be grayed out unless a REGZA-L[NK compatible audio receiver is connected.
Selectingthe color temperature Usingthe advanced picture settings features You call change tile quality of the picture by selecting from three preset color temperatures (Cool, Medium, and Warm), as described below. UsingDynamicContrast Dynamic Contrast detects changes in picture quality that affect the appearance of your contrast settings and then automatically adjusts the video.
Selecting the cinemamode Usingthe Film Stabilization feature When you view a DVD (3:2 pulldown processed) from a DVD player connected to the VIDE0 1, VIDEO2, C010rStream liD (component video), or HDNI inputs on the TV. smoother motion can be obtained by setting the Cinema Node to Film. This feature helps to eliminate video shaking.
UsingNPEGnoisereduction The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. Choices for MPEG noise reduction are Off, Low,Middle, and High.Off is automatically selected when this feature is disabled ("grayed out"). To select the MPEG noise MENU 1 Press 2 Highlight 3 Press 4' © and open reduction and press A or V to highlight the field, and then press 4 either Low,Middle 0|[ or _ press @.
Noisy picture Generaltroubleshooting Before calling a service technician, please check this chapter for a possible cause of the problem and some solutions you can try. * [f you are watching an analog channel (offair broadcast or Cable TV), you can set the CableCleaV' feature to reduce visible interference in the TV picture . Black box on-screen • The closed caption feature is set to one of the Text modes ([1, T2, T3, or T4). Set the closed caption feature to Off (_:_ page 43).
Soundproblems * Check 2). Closed caption problems the antenna/cable connections (_ Chapter . The station may have broadcast another channel. . . The sound may be muted. Press VOLUME. if you hear 11o sound, try setting the MTS feature to Stereo mode (_:_ page 45). if you are not receiving a second audio program from a known SAP source, make sure the MTS . . difficulties. Try feature is set to SAP mode (_ page 45).
Network Setup fails (Auto) ,, Copyright ,_ The LAN cables are not connected all. Connect all cables. ,, properly or at "The DHCP service is not enabled oll the router, or no router is present. Refer to your router's documentation for instructions on enabling DHCE If you do not have a router, you must manually set up the network address" Network Setup fails (Manual) ,, ,, DLNA played.
Specifications No te: ° This model complies with the specifications listed below. o Designs and specifications are subject to change without notice. . This model may not be compatible with features and/or specifications that may be added in the future.
AcceptaNe signal formats for PCiN and HDN! terminals PC IN signal formats Note: Depending on the connected PC, the following status may occur; incorrect display, fa/se format detection, picture position failure, blur, or judde_ But this is not a malfunction of your TV VGA 640 x 480 59.940Hz 31.469kHz 25.175MHz SVGA 800 x 600 60.317Hz 37.879kHz 40.000MHz XGA 1024 x 768 60.004Hz 48.363kHz 65.000MHz WXGA 1280 x 768 59.870Hz 47.776kHz 79.500MHz 1360 x 768 60.015Hz 47.712kHz 85.
Limited United States Warranty for LCD Televisions THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING CONDITIONS: This Limited Warranty is extended only to the original purchaser and only covers product purchased as new. Toshiba America Consumer Products, L.L.C. CTACP') makes the following limited warranties to odginal consumers in the United States.
TOTHE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITEDTO, LOST PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR INABILITY TO USE THIS LCD TELEVISION). No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any manner whatsoever.
h. i. j. Service of a Television on which the TOSHIBA label or logo, rating label or serial number have been defaced or removed; Damage to the Television caused by failure to follow the specifications, User manuals or guides as to usage and/or storage. Firmware updates that are posted to the Toshiba Support website and can be performed by the end user via a USB stick or SD card type media.
shall be and remain valid and enforceable. If and to the extent that any provision of this limited warranty as it relates to any of the Related Parties is found to be invalid or unenforceable in resoect of that oarty (the "Excluded Party') the Excluded Party shall be deemed to be severed or excluded from the provision, and the provision shall rersain valid enforceable and applicable in respect of the other or rersaininq Related Parties.
40_46 55GS001J F_N_ASindb 71 2010/5/16 7c@ 05:44:27
TOSHIBA AMERICA PRDDUCTSj CONSUMER L.L.C. Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A. NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A. TOSH|BA OF CANADA LTD.