Operation Manual

90
CONTROLS AND FEATURES
English
In order to receive sound from a connected PC, plug the audio
cable into the back of the television (as shown in the ‘Connecting
a computer’ section), and then use the PC/HDMI 3 Audio
setting.
a In the Preferences menu, press B or b to select AV
Connection and press OK.
b Press B or b to select PC/HDMI 3 Audio and press C
or
c to select the PC option.
NOTE: Selecting the PC option will force HDMI 3
Audio to Digital mode.
The AUDIO terminals for the COMPONENT VIDEO INPUT (EXT 2)
and VIDEO INPUT (EXT 3) are shared.
Select an appropriate option (EXT 2 or EXT 3) for the input that
you are using.
a In the Preferences menu, press B or b to select AV
Connection and press OK.
b Press B or b to highlight Side Shared Audio, and
then press
C or c to select EXT 2 or EXT 3.
If the connected HDMI source does not support digital audio,
plug the audio cable into PC/HDMI 3 (AUDIO) on the back of
the television (as shown in the ‘Connecting an HDMI® or DVI
device to the HDMI input’ section on page 13), then use the
HDMI 3 Audio setting.
a In the Preferences menu, press B or b to select AV
Connection and press OK.
b Press B or b to select HDMI 3 Audio and press C or
c to select Auto or Analogue.
If the sound is absent, try selecting a different setting.
NOTE: HDMI 3 supports digital and analogue sound,
HDMI 1, HDMI 2 and HDMI 4 are digital sound only.
Certain DVD disk formats may not output from this TV
(32/44.1/48kHz and 16/20/24 bits are acceptable).
Some early HDMI equipment may not work properly with your
HDMI TV. Please try setting the Enable Content Type and
INSTAPORT™ options to Off. Adjusting these settings should
allow your early HDMI source to operate properly with your
television.
a In the Preferences menu, press B or b to select AV
Connection and press OK.
b Press B or b to select HDMI Settings and press OK.
NOTE: HDMI Settings is grayed out on non-HDMI
inputs.
c Press B or b to select an item and press C or c to
select a setting.
• Enable Content Type: On
This feature is part of the HDMI standard.
When set to On, the TV will automatically adjust
settings according to the content type data sent
from the connected HDMI device.
• INSTAPORT™: On
This feature reduces the lag time when switching
HDMI sources.
•RGB Range: Auto
This feature adjusts RGB full range signal
automatically. When Limited is selected, RGB signal
is output in the range from 16 to 235. When Full is
selected, RGB signal is output in the range from 0 to
255.
NOTE:
• If your HDMI connection is capable of 1080p and/or your
television is capable of refresh rates greater than 50Hz or
supports Deep Colour, you will need a Category 2 cable.
Conventional HDMI/DVI cables may not work properly with
this mode.
• All of the above HDMI settings need proper HDMI source
devices.
If the HDMI source products do not support these features,
the television may not work properly by activating these
features.
When connecting a surround sound amplifier to the digital audio
output (Sony/Philips Digital Interface Format [S/PDIF]), the
following options can be selected or adjusted.
a In the Preferences menu, press B or b to select AV
Connection and press OK.
PC Audio
Side Shared Audio
HDMI 3 Audio
AV Connection
Input Labeling
PC/HDMI 3 Audio
PC
Side Shared Audio
EXT 2
HDMI 3 Audio
Auto
HDMI Settings
Digital Audio Output
HDMI Settings
Digital Audio Output
HDMI Settings
Enable Content Type
INSTAPORT
TM
On
On
RGB Range
Auto