OWNER'S MANUAL Integrated Digital LCD TV 32WLT66A 37WLT66A 42WLT66A 47WLT66A Owner's Record You will find the model number and serial number on the back of the TV. Record these numbers in the spaces provided below. Refer to them whenever you call upon your TOSHIBA dealer regarding this product. Model number: Serial number: DVB registration identification reference number: 4165 (32WLT66A), 4073 (37WLT66A), 4074 (42WLT66A), 4075 (47WLT66A).
Contents Introduction Welcome to Toshiba. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Welcome to Toshiba • Thank you for purchasing this Toshiba LCD Color Television. This manual will help you use the exciting features of your new TV. • Instructions in this manual are based on using the remote control. • Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference. Important Safety Instructions 4) Never block or cover the slots and openings in the cabinet. • Never place the TV so that it is facing upward or on its side.
Introduction 8) Install the TV in a horizontal, stable location. Connect between two clips on the back of the TV and a wall, pillar, etc., with a sturdy tie and clip of supplied accessories (- page 42). • Use as short a tie as possible to ensure the TV is stable. • If the TV is not installed securely, it may lean or fall over and cause an injury.
Introduction 5) When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet for safety. • The TV is not completely disconnected from the power supply line, as minute current is consumed even when the ! Power switch is turned off. • The Mains plug or an appliance coupler is used as the disconnect device, therefore the disconnect device shall remain readily operable. Service 1) Never repair, modify or disassemble the TV by yourself.
Introduction Cleaning Important information 1) Remove the power plug before cleaning. Never use solvents such as benzine or thinner to clean the TV. • These solvents may distort the cabinet or damage its finish. • If rubber or vinyl products remain in contact with the TV for a long time, a stain may result. If the cabinet becomes dirty, clean it with a soft, dry cloth. When cleaning the surface of the LCD display, wipe the panel surface gently with a soft, dry cloth.
Getting started Connecting an antenna Exploring your new TV Optimum reception of color requires a good signal and will generally mean that an outdoor antenna must be used. The exact type and positioning of the antenna will depend upon your particular area. Your Toshiba dealer or service personnel can best advise you on which antenna to use in your area. Before connecting the antenna cable, turn off all main power switches. VHF Installing the remote control batteries Remove the battery cover.
Getting started TV top and front panel controls • You can operate your TV using the buttons on the top or front panel, or the remote control. The back and side of the panel provide the terminal connections to connect other equipment to your TV (- “Connecting your TV” pages 33 - 38). • For the use of each control, see the pages in brackets. for 32WLT66A/37WLT66A/42WLT66A TV top view TV front view You can swivel the TV screen. Swivel angle: 15 degrees to left and right.
Getting started TV side and back panel connections for 32WLT66A/37WLT66A/42WLT66A 11 TV back view DIGITAL T V 12 * You can use the cable holder to hold antenna cable, video and audio cables etc. When moving the TV, never hold this holder.
Getting started Learning about the remote control Location of controls Power on/Standby (- page 12) To switch between Analog and Digital TV (- page 11) Number buttons (0-9) (- pages 16, 24) • Input source selection (o1 - o2, HDMI1, HDMI2, PC) (- page 25) • To access sub-pages when in teletext - analog only (- page 26) To return to the previous program (- page 16) To display digital on-screen information (- page 29) To switch between Navigation List and Favorite List (- pages 16, 31) EXIT (- page 12)
Getting started This integrated TV is equipped with both Digital and Analog system. To switch between Digital and Analog TV press ATV/DTV on the remote control. Learning about the menu system We suggest you familiarize yourself with the display charts before using the menu system: • Press M to display menu, then press I or i to select main menu headings. • Press u or U to select an item. • Press I or i to select or adjust setting. • Press Q to display the next menu.
Getting started Notes for menu system: • In the video input mode (o1 , o2), Auto tuning and Manual tuning are not available. Instead, Manual setting appears in the SET UP menu (- page 25). • If you connect external equipment via component video source to external input, Color system selection in the Manual setting menu is not available. • If you do not make a selection for a while, the menu display disappears automatically. • If you want to close the menu display instantly, press P.
Getting started Tuning the TV for the first time - digital only - Before switching on the TV, put your decoder and media recorder to Standby if they are connected and ensure the antenna is connected. To setup the TV use the buttons on the remote control as detailed on page 10. 1 Press , the Welcome screen will appear. This screen will appear the first time that the TV is switched on and each time the TV is reset.
Getting started Note: After the Auto scan, the TV may have scanned identical channels being broadcast from different transmitters. You can verify this by previewing those channels in the Channel List with identical logical numbers and check on their physical channel numbers (- page 30).
Getting started Manually setting channels in the channel memory - analog only Use the Manual tuning operation if desired channels cannot be preset with the Auto tuning or if you would like to preset channels to specific position numbers one by one. 1 From the SET UP menu, press u or U to select Manual tuning. 2 Press Q to display the Manual tuning menu. Press u or U to select the program position you want to arrange. Manual tuning Label Prog.
Getting started Watching TV programs Switching between two program positions Viewing Digital programs - digital only - 1 2 Select the first program position you want to view. 3 Press :. The previous channel will be displayed. You can switch two program positions without entering actual position number each time.
Getting started I-Plate contains the following information: • Current Channel Number • Network Name • Favorite status (indicated by a heart icon) • Channel Lock status (indicated by a padlock icon on first I-Plate) • Now and Next Program Names • Current date and time • Received program video format (SD/HD) • Teletext availability (indicated by TTX) • Subtitle (closed-caption) availability (indicated by CC) • Parental Guidance code (PG, MA, G, R, etc.
Using the TV’s features (General) the range of wide-screen formats (16:9, 14:9, 20:9 etc.), you may see bars on the top and bottom of the screen. Picture adjustment Selecting the picture size 1 2 Press and hold O until the picture size list appears on the screen, then press u or U to select the appropriate picture size (or press O repeatedly to select required picture size directly). The antenna input signal Wide Super Live 2 Cinema 2 4:3 Super Live 1 Cinema 1 Subtitle 14:9 Press Q.
Using the TV’s features (General) Using the picture still Selecting the picture mode • Press R to freeze the picture. Even if an image is frozen on the TV screen, the pictures are running on the input source. Audio continues to be output as well. To return to a moving picture, press R again. You can select the picture quality instantly among three preset modes and one user-set mode. • Press N to select the desired picture quality.
Using the TV’s features (General) Activating the black stretch Adjusting the color management This function increases the strength of dark areas of the picture which improves definition. You can adjust the picture color quality by selecting from 6 base color adjustments : Red, Green, Blue, Yellow, Magenta or Cyan. 1 From the Picture settings menu, press u or U to select Black stretch on the 2nd page.
Using the TV’s features (General) Using the cinema mode - analog only A movie film’s picture runs at 24 frames a second, whereas movie software such as DVD, etc., that you enjoy watching on television at home runs at 30 (NTSC) or 25 (PAL) frames a second. To convert this signal to reproduce a smooth motion and picture quality, select the On mode. Effective signal and setup conditions: • When the Video input mode is selected. • When the input signal format is 480i and 576i signals.
Using the TV’s features (General) Selecting the bilingual programs - analog only - Sound adjustment Setting the MTS (Multi-channel TV Sound) 1 2 - analog only - When a bilingual program is received, e Dual appears. Press S to select the sound to be heard. The sound differs according to the transmission system: NICAM or German stereo/bilingual broadcast. Auto mode Dual 1 The MTS Auto mode automatically recognize stereo/bilingual programs depending on the broadcast signal.
Using the TV’s features (General) Using the SRS WOW surround sound Using the bass boost SRS WOW is a special combination of SRS Labs audio technologies that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer and wider. WOW consists of three features; SRS 3D, FOCUS, and TruBass, being turned on. 1 From the SOUND menu, press u or U to select Bass boost on the 2nd page. 2 Press I or i to select On.
Using the TV’s features (General) 3 The timers Press u or U to select an empty slot to program a timer or any existing program to be edited, then press Q. Timer Tuesday, 14 Nov 2006 06:44 Setting the Time zone - digital only Mode Start End 0006 Channel 5 Weekly-Sat 18 Nov 2006 20:30 21:00 0007 Channel News Asia Daily 14 Nov 2006 00:00 00:00 0008 Channel 8 Daily 14 Nov 2006 00:00 00:00 0009 Channel U Once 14 Nov 2006 00:00 00:00 Ch. No.
Using the TV’s features (General) Selecting the timer menu - analog only The Timer is especially useful if you want the TV to turn itself on or off after a selected period of time. 1 Press M, then press I or i to display the TIMER menu.
Using the TV’s features (General) 1) Press u or U repeatedly to select a character for the first space, then press i. *(blank space) 2) Repeat step 1) to enter the rest of the characters. If you would like a blank space in the label name, you must choose a blank space from the list of characters. 3) Press Q to store your settings.
Using the TV’s features (General) Using Auto mode Using LIST mode There are two Modes: Auto will display FASTEXT or TOPTEXT, if available. LIST will display your four favorite pages. In either mode, as an alternative to the colored buttons, you can access a page by entering a 3-digit number, using the Number buttons on the remote control, or to advance to the next page, press >, to go back to the previous page press <. To change between Auto and LIST, see above. • Press to access teletext.
Using the TV’s features (General) Teletext buttons on the remote control Below is an introduction to the teletext buttons on your remote control and their functions. Teletext in Digital TV 1 In Auto-mode Press k to access the index page. The one displayed is dependant on the broadcaster. In LIST-mode Press k to return to the 100 page or initial page. When I-Plate indicates the presence of Teletext (TTX) in a channel, press d to view Teletext.
Other Digital TV features and settings Setting the EPG (Electronic Program guide) 1 2 3 Press M, then I or i to select PROGRAM menu. Press u or U to select EPG then, press Q to display 7 Days EPG or Present EPG. Alternatively, press a to display EPG directly. Press a button to select, 7 Days EPG or Present EPG.
Other Digital TV features and settings Parental rate 5 Press u and U to select channels, then press Q to preview the channel. When channel with is selected, you will see the video being displayed in the preview window. And when channel with is selected, preview window displays radio-graphics, along with the detailed channel information shown below the window. 6 Press the Yellow button to mark the channel as favorite ( ). To reset, press the Yellow button again.
Other Digital TV features and settings Favorite Channel List Information, restore factory setting 1 When viewing in Digital TV, press b to display the Navigation Channel list. 2 Press b again to display Favorite Channel list. This function can be used to check the version of hardware and software currently installed.
Other Digital TV features and settings Digital Output, Audio Track Digital Output This function selects an output sound format corresponding to your audio system connection. It affects the audio format from the Digital Audio output terminal (- page 9). 1 2 Transparency 1 From the PROFILE menu, press u or U to select Transparency, then press Q. 2 Press I or i to adjust the degree of On-Screen-Display transparency. Transparency From the PROFILE menu, press u or U to select Digital Output.
Connecting your TV Back connections Connection example for 32WLT66A/37WLT66A/42WLT66A TV back view VCR (Recording) DIGITAL T V VIDEO L VIDEO AUDIO Y R L/MONO PB/CB AUDIO PR/CR DVD video player (with component video outputs or L R R COMPONENT VIDEO INPUT PC/HDMI-1 (AUDIO) Set Top Box or TV back view HDMI or DVI device • Before connecting any external equipment, turn off all main power switches.
Connecting your TV Connecting an amplifier equipped with a Dolby Digital decoder Connecting an amplifier equipped with a digital audio (optical) input Amplifier equipped with digital audio input Amplifier equipped with Dolby Digital decoder TO OPTICAL type digital audio input TV back view TO OPTICAL type digital audio input Optical digital cable (not supplied) TV back view Optical digital cable (not supplied) DIGITAL T V DIGITAL T V VIDEO VIDEO L COMPONENT L VIDEO INPUT VIDEO Y COMPONENT VIDEO
Connecting your TV Side connections Connecting an HDMI or a DVI device You can connect a wide variety of auxiliary equipment via the terminals located on the right side of the panel o (2). Please always refer to the owner’s manual of the equipment to be connected for full details. • This TV is not intended for connection to and should not be used with a PC. • When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.
Connecting your TV Connecting an HDMI device Selecting the PC/HDMI1 audio mode One HDMI cable (type A connector) You can select PC audio or HDMI1 audio when using this function (- page 35). TV back view 1 2 Press M, then press I or i to display the SET UP menu. Press u or U to select AV connection, then press Q to display the AV connection menu.
Connecting your TV Signal names for mini D-sub 15 pin connector Connecting a computer Pin assignment for RGB/PC terminal An analog RGB (15 pin) computer cable can be connected. 1 6 11 5 10 15 TV back view VIDEO TV back view Mini D-sub 15 pin L L AUDIO Signal name Pin No. Signal name 1 R 9 NC 2 G 10 Ground 3 B 11 NC 4 NC (not connected) 12 NC 5 NC 13 H-sync 6 Ground 14 V-sync 7 Ground 15 NC 8 Ground R R DIGITAL T V Pin No.
Connecting your TV Adjusting the sampling clock Using the PC setting • In the PC input mode, you cannot select the 3D color management and Base color management in the PICTURE menu and the Color, Tint, Sharpness, Black stretch, MPEG NR and DNR in the Picture setting menu and Cinema mode (- page 21). • In the PC input mode, the Manual setting (- page 25) is not displayed.
Reference section Troubleshooting Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions. Symptom and solution TV will not turn on • Make sure the power cord is plugged in, then press ! and 1. • The remote control batteries may be dead. Replace the batteries. No picture, no sound • Check the antenna connections. No sound, picture OK • The sound may be muted. Press 2+, 2– or U. • The station may have broadcast difficulties.
Reference section APPENDIX AUSTRALIAN PARENTAL GUIDANCE CODES (Normative) Recommended On-Screen-Display for parental guidance codes transmitted within DVB-SI EIT information using the DVB parental_rating_descriptor.
Reference section Broadcast system Broadcast transmission systems of each country or region Asia M.E. Country or region Color Sound Bahrain, Kuwait, Israel, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, etc. PAL B/G China PAL D/K China Hong Kong PAL I Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. SECAM B/G Russian Federation, etc. SECAM D/K Myanmar, etc. NTSC M Country or region Color Sound Australia, New Zealand, etc.
Reference section Aspect ratio 16 : 9 Visible size (diagonal) 32WLT66A: 80.0 cm, 37WLT66A: 94.0 cm 42WLT66A: 106.7 cm, 47WLT66A: 119.6 cm Number of pixels 32WLT66A, 37WLT66A, 42WLT66A: 1,366 (H) dots 5 768 (V) dots 47WLT66A: 1,920 (H) dots 5 1,080 (V) dots Audio power 10 W + 10 W (10 % THD) Speakers 32WLT66A, 37WLT66A, 42WLT66A: Main 60 5 120 mm 2 pcs. 47WLT66A: Main 60 5 120 mm 4 pcs. Tweeter 33 mm (round) 2 pcs.
Reference section 43