User Manual
English - 17 -
(**) Limited Models Only
devices. Both of the devices must be connected to the same
network. This feature is only functional on TV source.
CEC
This function allows the user to control the CEC-
enabled devices, that are connected through HDMI
ports by using the remote control of the TV.
The CEC option in the Settings>System>Device
Settings menu should be set as Enabled
Press the Source button and select the HDMI input
of the connected CEC device from the Sources List
menu. When a new CEC source device is connected,
it will be listed in Sources menu with its own name
instead of the connected HDMI port’s name (such as
DVD Player, Recorder 1, etc.).
The TV remote is automatically able to perform the
main functions after the connected HDMI source has
been selected. To terminate this operation and control
the TV via the remote again, press and hold the “0-
Zero” button on the remote control for 3 seconds.
You can disable the CEC functionality by setting the
related option under the Settings>System>Device
Settings menu accordingly.
The TV supports ARC (Audio Return Channel). This
feature is an audio link meant to replace other cables
between the TV and an audio system (A/V receiver or
speaker system).
When ARC is active, the TV will mute its other audio
outputs, except the headphone jack, automatically and
volume control buttons are directed to the connected
audio device. To activate ARC set the Sound Output
option in the Settings>Sound menu as HDMI ARC.
Note: ARC is supported only via the HDMI2 input.
Enhanced Audio Return Channel (eARC)(**)
Similar to ARC, the eARC feature enables the transfer
of the digital audio stream from your TV to a connected
audio device via the HDMI cable. eARC is an improved
version of ARC. It has a much higher bandwidth than
its predecessor. Bandwidth represents the range of
frequencies or amount of data that is being transferred
at a time. Higher bandwidth translates into a higher
amount of data that can be transferred. Higher
bandwidth also means that digital audio signal doesn’t
have to be compressed and is much more detailed,
rich, and vibrant.
When eARC is enabled from the sound menu, the
supported by the connected device, the output turns
into eARC mode and the “eARC” indicator can be
observed on the connected device’s OSD. If an eARC
link cannot be established (for example, the connected
device is not supporting eARC but supporting ARC
only) or if eARC is disabled from the sound menu,
then the TV initiates ARC.
For eARC to function properly;
The connected audio device should also support eARC.
Some HDMI cables do not have enough bandwidth to
carry high-bit-rate audio channels, use an HDMI cable
with eARC support (HDMI High Speed Cables with
Ethernet and the new Ultra High Speed HDMI Cable
- check hdmi.org for latest info).
Set the Sound Output option in the Settings>Sound
menu to HDMI ARC. The eARC option in the Sound
menu will be enabled. Check to see if it is set to On.
If not, set it to On.
Note: eARC is supported only via the HDMI2 input.
System Audio Control
the TV. The volume can be controlled using the re-
mote control of the TV. To activate this feature set the
Sound Output option in the Settings>Sound menu
as HDMI ARC. When HDMI ARC option is selected,
CEC option will be set as Enabled automatically, if it
is not already set. The TV speakers will be muted and
the sound of the watched source will be provided from
the connected sound system.
Note: The audio device should support System Audio Control
feature.
Game Mode
You can set your TV to achieve lowest latency for
games. Go to Settings>Picture menu and set the
Mode option to Game. Game option will be available
when the TV’s input source is set to HDMI. When set
the picture will be optimised for low latency.
Auto Low Latency Mode
You can also enable the ALLM (Auto Low Latency
Mode) option in the Settings>System>Device
Settings menu. If this function is enabled the TV
automatically switches the picture mode to Game when
the ALLM mode signal is received from the current
HDMI source. TV switches back to previous picture
mode setting when the ALLM signal is lost. So you
won’t need to change the settings manually.
If the ALLM option is enabled, picture mode can not
be changed as long as the ALLM signal is received
from the current HDMI source.
In order for the ALLM feature to be functional the related
HDMI source setting should be set to Enhanced. You can
change this setting from the Sources>Source Settings
menu or from the Settings>System>Sources menu.
E-Manual
E-Manual.
To access the E-Manual, enter Settings menu, select
Manuals and press OK. For quick access press Home
button and then Info button.
By using the directional buttons select a desired
topic and press OK to read instructions. To close the
E-Manual screen press the Exit or Home button.
Note: Depending on model, your TV may not support this
function. The content of the E-Manual may vary according
to the model.