User’s Manual A300 computers.toshiba-europe.
A300 Copyright © 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
A300 Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. U.S. Pat. No’s. 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 and other U.S. and world-wide patents issued and pending.
A300 Safety instructions Use the following safety guidelines to help to protect yourself and your computer. When using your computer Do not operate your portable computer for an extended period of time with the base resting directly on your body. With extended operation, heat can potentially build up in the base. Allowing sustained contact with the skin could cause discomfort or, eventually, a burn. ■ Do not attempt to service the computer yourself. Always follow installation instructions closely.
A300 EU Declaration of Comformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
A300 The consequences of the use of this product in non-approved working environments may be: ■ Interference with other devices or machines in the near surrounding area. ■ Malfunction of, or data loss from, this product caused by disturbances generated by other devices or machines in the near surrounding area. Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non-approved working environments before use.
A300 Following information is only for EU-member States Disposal of products The symbol indicates that this product may not be treated as household waste. Please ensure this product is properly disposed as inappropriate waste handling of this product may cause potential hazards to the environment and human health. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
A300 ENERGY STAR® Program Your computer model may be Energy Star® qualified. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the Environmental Protection Agency’s (EPA) ENERGY STAR® Program and has designed this computer to meet the latest ENERGY STAR® guidelines for energy efficiency.
A300 Optical disc drive standards TOSHIBA A300 computer is shipped with one of the following drives preinstalled: DVD Super Multi (+-R DL) drive or DVD Super Multi (+-R DL) / w Label Flash drive. The drive has one of the following labels: CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE1 KLASS 1 LASER APPARAT Before it is shipped, the Class 1 Laser is certified to meet the United States Chapter 21 Standards of the Department of Health and Human Services (DHHS 21 CFR).
A300 DVD Super Multi (+-R DL) drive Panasonic UJ-870B/UJ-870F/UJ870AB/UJ870EB Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED Panasonic Communications Co., Ltd. 1-62, 4-Chome Minoshima Hakata-ku Fukuoka, Japan HLDS GSA-T40N/GSA-T40F/GSA-T50N/GSA-T50F Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED Hitachi-LG Data Storage, Inc.
A300 Pioneer DVR-KD08TBM/DVR-KD08TBF/DVR-TD08TBM/DVRTD08TBF Location of the required label COMPLIES WITHFDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J MANUFACTURED PIONEER CORPORATION 4-1, MEGURO 1-CHOME, MEGUROKU TOKYO 153-8654, JAPAN Toshiba Samsung TS-L632H/TS-L632P/TS-L633A/TS-L633P Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J, APPLICABLE AT THE DATE OF MANUFACTURE.
A300 International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
A300 OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
A300 xiv User’s Manual
A300 Table of Contents Preface General Precautions Chapter 1 Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Utilities and applications . .
A300 Chapter 4 Operating Basics Using the touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 Using the fingerprint sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 USB Sleep and Charge function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9 Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11 Writing CD/DVDs on DVD Super Multi (+-R DL) drive . . . . . . . . . . . .
A300 External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A300 xviii User’s Manual
A300 Preface Congratulations on your purchase of the TOSHIBA A300 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells you how to set up and begin using your computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
A300 Chapter 6, Power and Power-up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.
A300 Display ABC Names of windows or icons or text generated by the computer that appear on its display screen are presented in the typeface you see to the left. Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read.
A300 xxii User’s Manual
A300 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
A300 Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
A300 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packaging materials for future use.
A300 Software Microsoft® Windows Vista™ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ Microsoft® Windows Vista™ Modem Driver (Can be used only for Modem models) Bluetooth Driver (Can be used only for Bluetooth models) Display Drivers for Windows Fingerprint utility (Can be used only for Fingerprint utility models) LAN Driver Pointing Device Driver Presto! BizCard 5 (Preinstalled with some models) Sound Driver for Windows ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Ulead DVD MovieFactory® for TOSHIBA Wireless LAN dr
A300 Features This computer incorporates the following features and benefits: Processor Built-in Please visit your region’s website for the configuration details of the model that you have purchased. Memory Slots PC2-5300 512MB, 1 GB or 2 GB memory modules can be installed in the two memory slots of all models.
A300 Video RAM Depending on the model you purchased. Mobile Intel® GM45 Express Chipset model/ Mobile Intel® GL40 Express Chipset model: Video RAM capacity shares with main memory, and the proportion depends on Dynamic Video Memory Technology. Mobile Intel® GM45 Express Chipset model/ Mobile Intel® PM45 Express Chipset model in graphic chip by ATI Mobility Radeon™ HD 3470: External 64/128/256 MB.
A300 DVD Super Multi (+-R DL) drive Some models are equipped with a full-size DVD Super Multi (+- R DL) drive module that allows you to record data to rewritable CD/DVDs as well as run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
A300 Pointing device Built-in A touchpad and control buttons in the palm rest enable control of the on-screen pointer. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord.
A300 HDMI This HDMI jack allows you to connect external display/audio devices. (Provided with some models) Multiple digital media slot This slot allows you to easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use flash memory (SD/SDHC/MS/MS Pro/MMC/xD memory cards). (Provided with some models) ExpressCard slot ExpressCard slot allows you to install an ExpressCard™/34 or ExpressCard™/54 to expand functionality. See Chapter 8, Optional Devices, for details.
A300 Modem Some computers in this series are equipped with an internal modem. The internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA, Canada, UK, France and Germany. Only V.90 is available in other regions.
A300 Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use. To access the Power Options, click Start -> Control Panel -> System and Maintenance -> Power Options. User’s Manual Hot keys Key combinations allow you to quickly modify the system configuration directly from the keyboard without running a system configuration program.
A300 1-10 Panel power on/off This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. This can be specified in the Power Options. Low battery automatic hibernation mode When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters hibernation and shuts down. This can be specified in the Power Options.
A300 TOSHIBA Value Added Package This section describes the TOSHIBA Component features preinstalled on the computer. TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features of more various power supply managements. TOSHIBA Button Support This utility controls the following computer button functions. ■ Mute button or LED On/Off button (Provided with some models) ■ CD/DVD button The starting application from the button can be changed.
A300 Utilities and applications This section describes preinstalled utilities and tells how to start them. For details on operation, refer to each utility’s online manual, help files or readme.txt files TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. HW Setup utility To start the utility, click the Windows Start button, point to All Programs, click TOSHIBA, click Utilities, and select HWSetup icon.
A300 TOSHIBA Face Recognition TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. If the verification is successful, the user will be logged into Windows automatically. The user can thus avoid having to enter a password or the like, which makes the login process easier. (Provided with some models) TOSHIBA Bluetooth Stack This software enables communication between remote Bluetooth devices.
A300 Windows Mobility Center This section describes the Windows Mobility Center. Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and the additional two tiles are added to your Mobility Center. ■ Lock Computer: This can be used to lock your computer without turning it off. This has the same function as the Lock button at the bottom of the right pane in the start menu.
A300 User’s Manual AC adaptor If you use your computer at more than one site, it may be convenient to purchase an additional AC adaptor (PA3468U-1ACA, PA3468E-1AC3, PA3516U-1ACA, PA3516E-1AC3, PA3290U-3ACA, PA3290E-3AC3) for each site so you will not have to carry the adaptor with you. USB FDD The USB floppy disk drive accommodates either a 1.44 MB or 720 KB floppy disk through connection to one of the computer’s USB ports.
A300 1-16 User’s Manual
A300 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The following figure shows the computer’s front with its display panel in the closed position. Front edge logo* Volume control Wireless communication switch* Headphone (S/PDIF) jack Microphone jack Multiple digital media card slot *Depending on the model you purchased.
A300 Set the switch to off in airplanes and hospitals. Check the Wireless communication indicator. It stops glowing when the wireless communication is terminated. 2-2 Multiple digital media slot This slot allows you to easily transfer data from devices, such as digital camera and PDA, that use flash memory (SD/SDHC/MS/MS Pro/MMC/ xD memory cards). Microphone jack A standard 3.5 mm mini microphone jack enables connection of a microphone or other device for audio input.
A300 Left side The following figure shows the computer’s left side. LAN jack Fan vent ExpressCard slot Video-out port* HDMI out port* USB port* External monitor port USB port i.LINK (IEEE1394) port eSATA/USB combo port* *Depending on the model you purchased. Figure 2-2 The left side of the computer External monitor port This 15-pin port allows you to connect an external monitor. Fan vent Provides air flow for the fan. Be careful not to block the fan vent.
A300 HDMI out port HDMI out port can connect with Type A connector HDMI cable. One HDMI cable can send and receive video, audio and control signals. (Provided with some models) LAN jack This jack allows you to connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 Mbit/s, 10BASE-T), Fast Ethernet LAN (100 Mbit/s, 100BASE-TX) or Giga-bit. The LAN has two indicators. See Chapter 4, Operating Basics, for details. Universal serial bus (USB 2.
A300 Keep foreign objects out of the ExpressCard slot. A pin or similar object can damage the computer’s circuitry. i.LINK (IEEE1394) port Connect an external device, such as a digital video camera to this port for high-speed data transfer. When multiple IEEE1394 devices are connected to a PC, the devices may not correctly be identified.
A300 Modem jack The modem jack allows you to use a modular cable to connect the modem directly to a telephone line. (Provided with some models) Optical disc drive A DVD Super Multi (+-R DL) drive. DC IN 19V The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer. Security lock slot A security cable attaches to this slot.
A300 Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery pack lock Battery pack Battery release Latch Memory module cover Figure 2-5 The underside of the computer User’s Manual Battery pack The battery pack powers the computer when the AC adaptor is not connected. The Batteries section in Chapter 6, Power and Power-up Modes, describes how to access the battery pack.
A300 Front with the display open The following figure shows the front of the computer with the display open. To open the display, lift it up and position it at a comfortable viewing angle. Web camera* Built-in microphone* Web camera LED* Display screen Function buttons* Stereo speaker (right)** Power button Fingerprint sensor* Stereo speaker (left)** Touchpad control buttons Touchpad System indicators *Provided with some models. **appearance depends on the model you purchased.
A300 User’s Manual Fingerprint sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled (Provided with some models): ■ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented. ■ Disable the password-protected screen-saver when returning from power-saving (Sleep) mode. ■ Single-Swipe Sign-On feature.
A300 Please handle your computer carefully to avoid scratching or damaging the surface. Function buttons Six buttons are provided with some models. Available for use: Mute or LED On/Off, CD/DVD, Play/Pause, Stop, Previous, Next. These buttons allow you to manage audio/video, run applications and access utilities. Refer to the Function buttons section in Chapter 4, Operating Basics for details.
A300 System indicators The following figure shows the system indicators, which light when various computer operations are in progress. Multiple digital media card** HDD/ODD/eSATA** DC IN** Power** Main battery** **appearance depends on the model you purchased. Figure 2-7 System indicators User’s Manual DC IN The DC IN indicator glows white/green when DC power is supplied from the AC power adaptor.
A300 Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CAPS LOCK indicator. When the CAPS LOCK indicator glows the keyboard is in all-caps mode. CAPS LOCK indicator Figure 2-8 CAPS LOCK indicator CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. When the F10 key indicator glows the keypad overlay allows you to control the cursor. When the F11 key indicator glows the keypad overlay allows you to enter numbers.
A300 Optical disc drive When the computer is accessing a CD/DVD, an indicator on the drive glows. Region codes for DVD drives and media Optical disc drive and media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.
A300 DVD Super Multi (+-R DL) drive The full-size DVD Super Multi drive (+-R DL) module allows you to record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
A300 Figure 2-11 The AC adaptor (3-pin plug) ■ Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. The output rating for the computer is 19 volts DC. ■ Please use only the AC adaptor supplied with the computer or an AC adaptor certified by TOSHIBA.
A300 2-16 User’s Manual
A300 Chapter 3 Getting Started This chapter provides basic information to start using your computer. It covers the following topics: Be sure also to read Instruction Manual for Safety and Comfort. This guide, which is included with the computer, explains product liability.
A300 Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-up Modes.
A300 Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. To open the display, lift the panel up and adjust it to the best viewing angle. While you open the display, hold the base of the computer to avoid raising it.
A300 Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft® Windows Vista™ Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of three modes: shut down (Boot) , hibernation mode or sleep mode. Shut down mode (Boot mode) When you turn off the power in shut down mode, no data is saved and the computer will boot to the operating system’s main screen. 1.
A300 Benefits of hibernation mode The hibernation feature provides the following benefits: ■ Saves data to the hard disk when the computer automatically shuts down because of a low battery. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in the Hibernate tab in Power Options. Otherwise, the computer will shut down in sleep mode. If battery power becomes depleted, data saved in sleep mode will be lost.
A300 Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the HDD/ODD/eSATA indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
A300 Executing sleep mode You can also enable sleep mode by pressing FN + F3. See Chapter 5, The Keyboard, for details. You can enter sleep mode in one of three ways: 1. Click Windows Start button, point to , and then click Sleep. 2. Close the display panel. This feature must be enabled. Refer to the Power Options in the Control Panel. 3. Press the power button. This feature must be enabled. Refer to the Power Options in the Control Panel.
A300 System Recovery Options A hidden partition of approximately 1.5GB is allocated on the hard disk drive for the System Recovery Options. This partition stores files which can be used to repair the system in the event of a problem. The System Recovery Options feature will be unusable if this partition is deleted. System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory.
A300 Creating Optical Recovery Discs This section describes how to create Recovery Discs. ■ Be sure to connect the AC adaptor when you create Recovery Discs. ■ Be sure to close all other software programs except the Recovery Disc Creator. ■ Do not run software such as screen savers which can put a heavy load on the CPU. ■ Operate the computer at full power. ■ Do not use power-saving features. ■ Do not write to the disc when the virus check software is running.
A300 Restoring the pre-installed software from your created Recovery Discs Please set your BIOS to default before you recover your computer to the factory state! If the pre-installed files are damaged, you are able to use the Recovery Discs you have created to restore the computer to the state it was in when you originally received it.
A300 Be sure to connect the AC adaptor, otherwise you may run out of battery during the recovery process. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Turn off the computer. 2. Turn on the computer and when the TOSHIBA screen appears repeatedly press the F8 key. 3. The Advanced Boot Options menu will be displayed. Use the arrow keys to select Repair Your Computer and press ENTER. 4. Select your preferred keyboard layout and press Next. 5.
A300 3-12 User’s Manual
A300 Chapter 4 Operating Basics This chapter gives information on basic operations including using the touchpad, the fingerprint sensor, optical disc drives, Audio/Video controls, the web camera, the microphone, the internal modem, wireless communication and LAN. It also provides tips on caring for your computer, diskettes and CD/DVD. Using the touchpad To use the touchpad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
A300 Using the fingerprint sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard. Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer).
A300 ■ Avoid swiping with the finger stiff or pressed-on too hard: Fingerprint reading may fail if the center of the fingerprint is not touching on the sensor, or when finger is swiped while pressing hard. Make sure that the center of the fingerprint is touching the sensor before swiping. ■ Confirm the center of the fingerprint whirl before swiping: The thumb’s fingerprint has a bigger whirl, which is prone to misalignment and distortions.
A300 ■ Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate ■ Soaked or swollen finger (e.g. after taking bath) ■ Injured finger ■ Wet finger ■ Soiled or oily finger ■ Extremely dry skin condition on finger Observe the following to improve the fingerprint recognition success rate. ■ Enroll two or more fingers.
A300 Points to note about the fingerprint utility ■ If Windows Vista™’s file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software. ■ You can back up the fingerprint data or the information registered to Password Bank. ■ Please use Import/Export menu on Fingerprint Software Management. ■ Please also refer to the fingerprint utility Help file for more information.
A300 7. In case of finger injury or authentication failure, it is recommended that another fingerprint also be enrolled. The following message will be displayed: [We recommended enrolling at least two fingerprint images.] Click OK and repeat steps 3, 4, 5 and 6 with another finger. How to delete the fingerprint data Saved fingerprint data is stored in the Non-volatile memory inside the fingerprint sensor. If you hand over the PC to others, or dispose of it, the following operations are recommended. 1.
A300 Windows logon via fingerprint authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the PCs, as user selection can be skipped. Fingerprint authentication procedure 1. Start up the computer. 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor.
A300 How to enable fingerprint system boot authentication settings It is necessary to first enroll your fingerprint with the TrueSuite Access Manager application prior to enabling and configuring the fingerprint Pre-OS feature. Check that your fingerprint is enrolled before configuring the settings. 1. Swipe your finger across the fingerprint sensor. Or enter Windows password and click Next. 2. Click settings. 3. The Administrator Settings screen is displayed.
A300 Fingerprint utility limitations TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free. TOSHIBA does not guarantee that the fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility. ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint.
A300 ■ The USB Sleep and Charge function only works for compatible ports. This function is disabled in the default setting. To enable it, you must change [Disabled] to [Enabled] in HW Setup. ■ When USB Sleep and Charge function is set to [Enabled] in HW Setup, USB bus power (DC5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC5V) is similarly supplied to the external devices which are connected to the compatible ports.
A300 Using optical disc drives The full-size drive provides high-performance execution of CD/DVDs-based programs. You can run CD/DVDs without an adaptor. When the computer is accessing a CD/DVD, an indicator on the drive glows. Use the TOSHIBA DVD PLAYER application to view DVD-Video discs. Refer also to the Writing CD/DVDs on DVD Super Multi (+-R DL) drive section for precautions on writing to CD/DVDs. Loading discs To load CD/DVDs, follow the steps below and refer to figures. 1. a.
A300 2. Grasp the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in above figure. ■ Do not touch the laser lens.
A300 5. Push the center of the drawer to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the drawer is closed, the CD/DVD might be damaged. Also, the drawer might not open fully when you press the eject button. Figure 4-7 Closing the drawer Removing discs To remove the CD/DVD, follow the steps below and refer to below figure. Do not press the eject button while the computer is accessing the drive.
A300 Function buttons Six buttons are provided with some models.
A300 Before writing or rewriting ■ Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/-RW and DVD-R/+R/-RW/+RW/-RAM/ +R DL/-R DL disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI KAGAKU MEDIA CO., LTD. RICOH CO., LTD. CD-RW: (High-Speed, Multi-Speed) MITSUBISHI KAGAKU MEDIA CO., LTD.
A300 DVD-R for Labelflash™: FUJIFILM CORPORATION. DVD+R for Labelflash™: FUJIFILM CORPORATION. This DVD Super Multi (+-R DL) drive cannot use discs that allow writing faster than 8x speed (DVD-R, DVD+R and DVD+RW media), 6x speed (DVD-RW media), 5x speed (DVD-RAM media) and 4x speed (DVD-R DL and DVD-R DL media). ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.
A300 ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver, which can put a heavy load on the CPU. ■ Operate the computer in the full-power mode. Do not use power-saving features. ■ Do not write while virus check software is running. Wait for it to finish, and then disable virus detection programs including any software that checks files automatically in the background.
A300 Disclaimer (DVD Super Multi (+-R DL) drive) TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/-RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/ DVD-RAM disc that may be caused by writing or rewriting with this product.
A300 ■ If you add data to a DVD-R, DVD-R DL, DVD+R or DVD+R DL disc that you have already recorded to, you might not be able to read the added data under some circumstances. For example, it cannot be read under 16-bit operating systems, such as Windows 98SE and Windows Me, while in Windows NT4 you will need Service Pack 6 or later, and in Windows 2000, you will need Service Pack 2. In addition to this, some DVD-ROM and DVD-ROM/CD-RW drives cannot read this added data regardless of the operating system.
A300 Video You can record video using Ulead DVD MovieFactory® for TOSHIBA. When using Ulead DVD MovieFactory® for TOSHIBA How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click Start -> All Programs -> DVD MovieFactory for TOSHIBA -> Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Insert a DVD-RW or DVD+RW disc in Burner. 3.
A300 Important information for use Note the following limitations when you write Video DVD: 1. Editing digital video ■ Log in with Administrator rights to use DVD MovieFactory. ■ Make sure that your computer is running on AC power when using DVD MovieFactory. ■ Operate the computer at Full Power. Do not use power-saving features. ■ While you are editing DVD, you can display preview. However, if another application is running. The preview might not display properly.
A300 ■ DVD-R/+R/+RW disc cannot be written in VR format. ■ Not support to output VCD and SVCD format. 3. About Straight to Disc ■ Not support to record on DVD-R/+R disc ■ Not support to record DVD+VR format by HDV ■ HDV support to burn DVD-Video only ■ DVD-VR format not support to add Menu 4. About recorded DVDs ■ Some DVD-ROM drives for personal computers or other DVD players may not be able to read DVD-R/+R/-RW/-RAM discs.
A300 Using the web camera Built-in web camera is provided with some models. This section describes the bundled webcam utility, which can capture still and video images. The web camera will auto-run when Windows starts. Please remove the protective plastic-film before using the Web Camera.
A300 Video recording Audio recording Capture still images Function Display window Camera resolution Effects Mute Figure 4-11 Using the Software 4-24 Capture Still Image Click to see a preview of the captured image; you can also e-mail the image. Video Recording Click to prepare for recording. Click again to start recording. One more to stop recording and see preview of the video. Audio Recording Click to start recording, Click again to stop and listen to a preview of the audio.
A300 Using the microphone You can use the built-in or an external microphone that connects to the microphone jack to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. (Built-in microphone is provided with some models) Since your computer has a microphone and speaker, “feedback” may be heard under certain conditions.
A300 Disclaimer Toshiba does not guarantee that the face recognition utility technology will be completely secure or error-free. Toshiba does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the face recognition software or utility.
A300 7. Once your face has been positioned properly, the recording will commence. Start moving your neck very slightly to the left and right, and then move your neck down and up. 8. Registration will end after you have repeatedly moved your neck left, right, down and up. When the register succeeds, below message will be displayed on the screen: Registration successful. Now we’ll do the verification test. Click the Next button. Click the Next button to perform the verification test. 9.
A300 Windows Logon via TOSHIBA Face Recognition This section explains how to login to Windows with TOSHIBA Face Recognition. Two authentication modes are provided. ■ AUTO Mode Login screen : If the face authentication tile is selected by default, you can log in without using the keyboard or mouse.
A300 Modem The availability of this feature is depending on the model you purchased. This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.
A300 Properties menu Click the icon with the secondary mouse button to display the following menu. Figure 4-13 The menu list (Windows Vista™) Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
A300 Connecting To connect the internal modem cable, follow the steps below. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack. Telephone jack Modem jack Figure 4-14 Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. Disconnecting To disconnect the internal modem cable, follow the steps below. 1.
A300 ■ Frequency Channel Selection (Revision A/draft N: 5 GHz, Revision B/G/draft N: 2.4GHz) ■ Roaming over multiple channels ■ Card Power Management ■ Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit encryption algorithm (Atheros module type). ■ 11a, 11b, 11g and 11n wireless are based on IEEE 802.11a, 802.11b, 802.11g and 802.11n respectively. The IEEE 802.11n specification has not been finalized and is currently in draft release.
A300 Security Two advanced security mechanisms ensure a high level of security: ■ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ■ Encryption prevents eavesdropping and maintains link privacy. Wireless communication switch You can enable or disable RF transmission(Wireless LAN, Bluetooth and WiMAX) functions on and off, with this switch (Provided with some models). No transmissions are sent or received when the switch is off.
A300 LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T)(depending on model you purchased). This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off.
A300 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN active indicator glows orange. When the computer is connected to a LAN hub but is not exchanging data, the link indicator glows green. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. Make sure the LAN active indicator (orange LED) is out before you disconnect the computer from the LAN. 1.
A300 Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Make sure all disk activities are terminated before moving the computer. Check if the HDD/ODD/eSATA indicator and external device indicator are off. ■ If a CD/DVD is in the drive, remove it. Also make sure the drawer is securely closed. ■ Turn off the power to the computer.
A300 Chapter 5 The Keyboard The computer’s keyboard layout is compatible with 104/105-key enhanced keyboard. Pressing FN key and other keys can execute all enhaced keyboard function. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, function keys, soft keys, Windows special keys and keypad overlay.
A300 Function keys: F1 … F12 The function keys, not to be confused with FN, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the FN key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: FN key combinations, in this chapter.
A300 Press FN + F12 (Scroll Lock) to lock the cursor on a specific line. The power on default is off. Press FN + ENTER to simulate ENTER on the enhanced keyboard’s numeric keypad. Press FN + CTRL to simulate the enhanced keyboard’s right CTRL key. Press FN + ALT to simulate the enhanced keyboard’s right ALT key. Hot keys Hot keys (pressing FN + a function or ESC key) allow you to enable or disable certain features of the computer.
A300 Hibernate Pressing FN + F4 switches the system to hibernation mode. Output Pressing FN + F5 changes the active display device. Brightness down Pressing FN + F6 decreases the computer’s display panel brightness in individual steps. Brightness up Pressing FN + F7 increases the computer’s display panel brightness in individual steps. Wireless Pressing FN + F8 switches the active wireless devices if the wireless communication switch is switched on.
A300 TOSHIBA zooming utility (reduce) Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows. TOSHIBA zooming utility (enlarge) Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows. FN sticky key You can use the Toshiba Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and they press an “F number” key.
A300 Keypad overlay Your computer’s keyboard does not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyboard with the relevant keys having dark gray letters at their front edge. The overlay provides the same functions as the numeric keypad on a standard 101/102-key enhanced keyboard. Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control.
A300 Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard functions without turning off the overlay : 1. Hold FN and press any other key. All keys will operate as if the overlay were off. 2. Type uppercase characters by holding FN + SHIFT and pressing a character key. 3. Release FN to continue using the overlay.
A300 5-8 User’s Manual
A300 Chapter 6 Power and Power-up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power-up modes.
A300 Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery blinking orange DC IN off Battery charge is exhausted Computer goes into hibernation or shuts down (depending on the Toshiba power Management Utility Setting) No battery installed • No operation • LED: Battery off DC IN off Power off (no operation) Power indicators The Battery, DC IN and Power i
A300 DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected. White/Green Indicates the AC adaptor is connected and supplying proper power to the computer. Orange Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, see your dealer. No light Under any other conditions, the indicator does not light.
A300 When the computer is powered off in hibernation and sleep mode, and the AC adaptor is not connected, the battery pack supply power to maintain data and programs in memory. If the battery pack is completely discharged, hibernation and sleep do not function and the computer loses all data in memory. One of the following messages appears when you turn on the power: The firmware has detected that a CMOS battery fail occurred. contiune The firmware has detected that a CMOS battery fail occurred.
A300 Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of batteries can cause death, serious injury or property damage.
A300 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet. A wet battery pack will overheat, ignite or rupture possibly resulting in death or serious injury. Warning 1. Never allow caustic electrolyte fluid leaked from a battery pack to contact your eyes, skin or clothing.
A300 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely. Sleep and hibernation will not function and data in memory will be lose. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor.
A300 Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (3 cell) 8 hours or more 2 hours Battery pack (6 cell) 8 hours or more 3 hours Battery pack (9 cell) 8 hours or more 4 hours RTC battery 24 hours 24 hours The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
A300 Monitoring battery capacity Remaining battery power can be monitored in Power Options. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
A300 Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods.
A300 Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install battery packs.
A300 6. Slide the battery release latch to free the battery pack for removal, then lift up the battery pack. Battery Release Latch Battery Pack Figure 6-2 Removing the battery pack 7. Pull the battery pack forward to remove it. For environmental reasons, do not throw away a spent battery pack. Please return spent battery pack to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
A300 Starting the computer by password If you have already registered a password, there are two ways to start the computer: ■ Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint Power-on Security. If you would not like to swipe your finger or cannot authenticate the fingerprint for some reasons, press the ESC key or click Switch User button to skip the fingerprint authentication screen.
A300 Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in sleep or hibernation mode but not in boot mode. If the panel power off function is enabled and use Shut down Windows, do not close the display until the shut down function is completed. System auto off This feature turns the system off automatically if it is not used for a set duration.
A300 Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup allows you to configure settings for General, Password, Display, CPU, Boot Priority, Keyboard, USB, LAN and Illumination. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
A300 General This window displays the BIOS version and contains two buttons: Default and About. Default Returns all HW Setup values to the factory settings. About Displays the HW Setup version. Setup This field displays the installed BIOS version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Changes or remove the password. (Default) Registered Sets the password. A dialogue box will appear to allow you to set the password.
A300 3. Click the OK button. If the character string you enter matches the registered password, the password option is reset and the display changes to: Not registered If they do not match, the following message appears. You must repeat step 1. Incorrect Password!!! If you enter the password incorrectly three times in a row, the computer need to shut off. You will not be able to access the password option in the HW Setup. In this case you must turn the power off and back on to retry the procedure. 4.
A300 Boot Priority Boot Priority Options This option sets the priority for booting the computer. If there is only 1 HDD, the Boot Priority Options setting will be like the following. If there are 2 HDDs, the Boot Priority Options setting will be like the following.
A300 You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB diskette drive. N Selects the network. 1 Selects the primary HDD. 2 Selects the secondary HDD. C Selects the CD-ROM*. This procedure does not affect the settings. * In this computer, CD-ROM refers to the DVD Super Multi (+-R DL) drive. ExpressCard HDD boot is not supported. To change the boot drive, follow the steps below. 1.
A300 USB Legacy USB Support Use this option to enable or disable USB Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB Legacy Emulation item to enabled. Enabled Enables the USB Legacy Emulation. (Default) Disabled Disables the USB Legacy Emulation. USB Sleep and Charge function This section describes the setting for USB Sleep and Charge function.
A300 LAN Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Enables the Wake-up on LAN. (Default) Disabled Disables the Wake-up on LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature. Built-in LAN Enabled Enables built-in LAN functions. (Default) Disabled Disables built-in LAN functions.
A300 7-8 User’s Manual
A300 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. The following optional devices are available from your TOSHIBA dealer: Cards/Memory ■ ExpressCard ■ SD, SDHC, MS, MS Pro, MMC, xD memory cards ■ Memory expansion Power devices ■ Additional battery pack (3 cell, 6 cell and 9 cell) ■ Additional AC adaptor Peripheral devices ■ ■ ■ ■ ■ ■ USB FDD Kit eSATA External monitor Television HDMI i.
A300 ExpressCard Installing an ExpressCard The ExpressCard slot is located on the left side of the computer. You can install one ExpressCard in the slot. Windows’ hot-install feature allows you to install ExpressCard while the computer’s power is on. Do not install an ExpressCard while the computer is in sleep or hibernation mode. Some cards might not work properly. To install an ExpressCard, follow the steps below. 1. There is a dummy card in the slot. Press the dummy card slightly to make it stretch out.
A300 5. Check the configuration in the HW Setup window to make sure it is appropriate for your card. ExpressCard Slot ExpressCard* *The card’s shape depends on the card you purchased. Figure 8-3 Inserting the ExpressCard Removing an ExpressCard To remove the ExpressCard, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the ExpressCard. 2. Press the ExpressCard slightly to make it stretch out. 3.
A300 Multiple digital media card slot The computer is equipped with a multiple digital media card slot that can accommodate Secure Digital (SD)/ Secure Digital High Capacity (SDHC)/ Memory Stick (MS)/Memory Stick Pro (MS Pro)/Multi Media Card (MMC)/ xD memory cards. These memory cards allow you to easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD/SDHC/MS/MS Pro/MMC/xD memory cards.
A300 ■ Keep foreign objects out of the multiple digital media card slot. A pin or similar object can damage the computer’s circuitry. ■ Make sure the SD/SDHC/MS/MS Pro/MMC/xD card is oriented properly before you insert it. ■ Memory Stick Duo/PRO Duo and the Memory Stick adaptor are not compatible with the multiple digital media card slot. Do not insert Memory Stick Duo/PRO Duo into the slot. Data may be lost or damaged if you use any card other than those supported.
A300 ■ Make sure the multiple digital media card slot indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. ■ Please do not remove the inserted memory card from the multiple digital media card slot while in sleep or in hibernation state. If you do, PC may become unstable or the data in the memory card may be lost.
A300 Figure 8-7 Removing the cover 6. Insert the memory module into the connector on the computer. Press the module carefully and firmly to ensure a solid connection. 7. Push the module down so that it lies flat and is secured by two latches. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.
A300 8. Seat the cover and secure it with one screw. 9. When you turn the computer on, it should automatically recognize the total memory capacity. Use the HW Setup program to verify that the added memory is recognized. If it is not recognized, check the module’s connection. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer.
A300 Additional battery pack (3 cell, 6 cell and 9 cell) You can increase the portability of the computer with additional battery packs (3 cell: PA3533U-1BRS/PA3533U-1BAS, 6 cell: PA3534U-1BRS/ PA3534U-1BAS, 9 cell: PA3535U-1BRS/PA3535U-1BAS). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-up Modes.
A300 When you turn on the power, the computer automatically recognizes the monitor and determines whether it is color or monochrome. You can use the HW Setup to select between Auto-Selected and LCD+Analog RGB displays. Refer to Chapter 7, HW Setup and Passwords. If you have selected LCD+Analog RGB under the Display options of the HW Setup, both the external monitor and the internal LCD will be active when you turn on the computer. If Auto-Selected is selected, only the external monitor will be active.
A300 HDMI Some models are equipped with HDMI out port than can send/receive video, audio and control signals by connecting with external display/audio devices. 1080p, 720p, 576p and 480p signal formats are supported, but actually available signal format depends on each HDMI devices. To connect external devices, follow the steps as detailed below: As the port operation of all HDMI (High-Definition Multimedia Interface) monitors has not been confirmed, some HDMI monitors may not function properly. 1.
A300 Settings for audio on HDMI To set the audio device to use the HDMI, follow the steps below. 1. Click Start. 2. Click Control Panel. 3. Click Hardware and Sound. 4. Click Sound. 5. Click Playback tab. 6. Click HDMI Device. 7. Click the Set Default button. To set the audio device to use internal speaker, follow the steps below. 1. Click Start. 2. Click Control Panel. 3. Click Hardware and Sound. 4. Click Sound. 5. Click Playback tab. 6. Click Speakers. 7. Click the Set Default button. i.
A300 ■ You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment. ■ If you connect/disconnect an i.LINK device to/from another i.LINK device that is currently exchanging data with the computer, data frames might be dropped. ■ Make sure data transfer has ended or turn off the computer, before you: ■ Connect/disconnect an i.LINK device to/from the computer. ■ Connect/disconnect an i.LINK device to/from another i.
A300 Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.
A300 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
A300 ■ Inspect all connecting cables for loose wires and all connectors for loose pins. ■ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem Sometimes the system gives clues that can help you identify why it is malfunctioning.
A300 Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
A300 Power When the computer is not plugged into an AC adaptor, the battery pack is the primary power source. However, your computer has a number of other power resources, including intelligent power supply and Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems. This section provides check lists for AC adaptor and the main battery. If you cannot resolve a problem after following them, the cause could lie with another power resource.
A300 Battery If you suspect a problem with the battery, check the DC IN indicator as well as the battery indicator. For information on indicators and battery operation see Chapter 6, Power and Power-up Modes. Problem Procedure Battery doesn’t power the computer The battery may be discharged - connect the AC adaptor to recharge the battery. Battery doesn’t charge when the AC adaptor is attached (Battery indicator does not glow orange).
A300 Password Problem Procedure Cannot enter password Refer to the Password section in Chapter 7, HW Setup and Passwords. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard and Chapter 7, HW Setup and Passwords. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press FN + F10 and try typing again.
A300 Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a diskette is in the diskette drive or a CD/DVD is in the optical disc drive. Remove any diskette and/or CD/DVD and check Boot priority. Refer to Chapter 7, Boot Priority section. There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk.
A300 Problem Procedure Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware not configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using. Refer to Chapter 1, Introduction, for more information. Check the region code on the DVD. It must match that on the drive. Region codes are listed in the Optical disc drive section in Chapter 2, The Grand Tour.
A300 Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touchpad Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to Pad shaped as an hourglass, wait for it to resume its operation normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility.
A300 USB mouse This section applies only with Windows Vista™ operating system. Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to mouse shaped as an hourglass, wait for it to resume its normal shape and try again to move it. operation Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility.
A300 Problem Procedure Fingerprint Pre-OS feature does not work Make sure you have enroll finger in windows account. Set the User Password by using TOSHIBA HW Setup and restart the system. Make sure place a checkmark in “Enable Pre-OS Fingerprint Authentication” on the TrueSuite Access Manager setting. ExpressCard Refer also to Chapter 8, Optional Devices. Problem Procedure ExpressCard error occurs Reseat the ExpressCard to make sure it is firmly connected.
A300 External monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hot keys FN + F5 to change the display priority and make sure it is not set for the internal display.
A300 TV output signal Problem Procedure Display on TV is poor Make sure the TV type is correct for your area: NTSC (US, JAPAN), PAL (Europe). No display Try adjusting the contrast and brightness controls on the external monitor. Press hot keys FN + F5 to change the display. Refer to Chapter 5, The Keyboard. If problems persist, contact your dealer.
A300 USB Sleep and Charge function Problem Procedure I cannot use the USB Sleep and Charge function The setting of USB Sleep and Charge function may be [Disabled]. Change the setting to [Enabled] in the HW Setup. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons. When the happens, disconnect an external device if some external devices are connected.
A300 Problem Procedure External devices connected to the compatible ports do not work when connected to a compatible port Some external devices may not work when connected to a compatible port when the USB Sleep and Charge function is [Enabled] in the HW Setup. Reconnect the external device after turning ON the computer.
A300 Modem Problem Procedure Communication software can’t initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Options in the Control Panel. You can hear a dial tone If the call is going through a PBX machine, make but can’t make a call sure the communication application’s tone dial detection feature is disabled. You can also use the ATX command.
A300 Sleep/Hibernation Problem Procedure The system will not enter sleep/ hibernation Is Windows Media Player open? The system might not enter sleep/hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select sleep/ hibernation. If problems persist, contact your dealer. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB.
A300 Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth Adpater is installed in the computer. The built-in Bluetooth function and an optional Bluetooth Adpater cannot operate simultaneously.
A300 TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first.
A300 9-20 User’s Manual
A300 Chapter 10 Disclaimers This chapter slates the Disclaimer(s) information applicable to TOSHIBA computers. CPU Central Processing Unit (CPU) Performance Disclaimer.
A300 64-Bit Computing. 64-bit processors are designed to take advantage of 32 and 64 bit computing. 64-bit computing requires that the following hardware and software requirements are met: ■ 64-bit Operating System ■ 64-bit CPU, Chipset and BIOS (Basic Input/Output System) ■ 64-bit Device drivers ■ 64-bit applications Certain device drivers and/or applications may not be compatible with a 64-bit CPU and therefore may not function properly.
A300 HDD drive capacity 1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Windows and/or pre-installed software applications, or media content. Actual formatted capacity may vary.
A300 Copy protection Copy protection technology included in certain media may prevent or limit recording or viewing of the media. Images All images are simulated for purposes of illustration. LCD brightness and eye strain Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
A300 Appendix A Specifications This appendix summarizes the computer’s technical specifications.
A300 Built-in modem The ability of this feature is depending on the model you purchased. Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications A-2 Communication system Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32 /V.32bis/V.
A300 Appendix B Display Controller The display controller interprets software commands into hardware commands that turn particular pixels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.
A300 B-2 User’s Manual
A300 Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications User’s Manual Form Factor ■ Mini Card Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
A300 Radio characteristics Radio characteristics of Wireless LAN cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4 GHz and 5 GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
A300 Table Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 2400-2483.5 MHz 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457*1 11 2462 12 2467*2 13 2472*2 When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
A300 Table Wireless IEEE 802.
A300 Appendix D AC Power Cord and Connectors The AC input plug of power cord must be compatible with various international AC power outlets. Power cords need to meet the local standards and the specifications listed as below: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.
A300 For the United States and Canada, two pin plug configuration must be 2-15P (250V) or 1-15P (125V); while three pin be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for USA, Australia, Canada, United Kingdom, Europe, and China.
A300 Appendix E If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
A300 TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. A300) Model number: (e.g. PSA30EYXT) Serial number: (e.g.
A300 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
A300 IDE: integrated drive electronics I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output TFT: thin-film transis
A300 analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
A300 byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
A300 components: Elements or parts (of a system) which make up the whole (system). Composite Video (YUV): A standard video signal used to transmit images, e.g. from a VCR to a TV. computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information.
A300 dialog box: A window that accepts user input to make system settings or record other information. Digital Audio: An audio compression standard that enables high-quality transmission and real-time playback of sound files. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head.
A300 E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT. erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems.
A300 H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware.
A300 IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte.
A300 mode: A method of operation, for example, the Boot Mode, Sleep Mode or the Hibernation Mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.
A300 parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user and supervisor.
A300 restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green and blue) or port for using such a device. See also CRT. RJ11: A modular telephone jack. RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation.
A300 T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. touchpad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
A300 Glossary-14 User’s Manual
A300 Index A C AC adaptor, 1-6, 2-6, 2-14, A-1 additional, 1-15, 8-9 connecting, 3-2 problems, 9-4 safety instructions, -iv, -xxiv ASCII characters, 5-7 Checklist equipment, 1-1 problems, 9-1, 9-3 Cleaning the computer, 4-35 COM port, 4-30 B Battery charging, 6-7 life, 10-2 monitoring capacity, 6-9 real time clock, 6-4 Real Time Clock battery, 1-6, 6-4 retention time, 6-10 types, 6-3 Battery pack, 1-6, 1-14, 2-7, 6-3 additional, 8-9 extending battery life, 6-10 indicator, 2-11, 6-2 location, 2-7 operat
A300 ExpressCard, 1-7 location of slot, 2-3 overheating, -xxiv problems, 9-10, 9-11 using, 2-4, 8-2 External monitor, 8-9 controller, B-1 HW Setup, 7-3 port, 1-6, 2-3 problems, 9-12 F Fan vent location, 2-3 Fingerprint sensor, 2-9 location, 2-8, 4-1 problems, 9-10 using, 1-13, 4-2 FM tuner using, 4-31 FN + 1 (TOSHIBA zooming utility reduce), 5-5 FN + 2 (TOSHIBA zooming utility enlarge), 5-5 FN + ALT (enhanced keyboard simulation), 5-3 FN + CTRL (enhanced keyboard simulation), 5-3 FN + ENTER, 5-3 FN + ESC
A300 I L i.
A300 P Password fingerprint sensor, 2-9 fingerprint utility, 1-13 power on, 1-9 problems, 9-6 starting the computer with, 6-13 user, 7-2 Pointing device problems, 9-9 touchpad, 4-1 Ports DC IN, 2-5 eSATA/USB combo, 2-3 external monitor, 2-3 HDMI, 2-3 headphone, 2-1 i.
A300 Soft keys emulating keys on enhanced keyboard, 5-2 ENTER, 5-3 right ALT key, 5-3 right CTRL key, 5-3 scroll lock, 5-3 Sound system, 1-7 headphone, 1-6, 2-2 microphone, 2-2, 2-9 speaker, 2-8 volume control, 2-2 T TOSHIBA Accessibility, 1-11 TOSHIBA Assist, 1-12 TOSHIBA Bluetooth Stack, 1-13 TOSHIBA ConfigFree, 1-12 TOSHIBA Disc Creator, 1-12, 4-18 TOSHIBA DVD-RAM utility, 1-12 TOSHIBA Face Recognition, 1-13 using, 4-25 Toshiba HW setup, 7-1 TOSHIBA PC Diagnostic Tool, 1-11 TOSHIBA support, 9-19 TOSHIB
A300 Index-6 User’s Manual
