TOSHIBA Barcode Printer B-852 SERIES Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Manuale Utente Manual do Utilizador
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: • Schallemission: unter 70dB (A) nach DIN 45635 (oder ISO 7779) • Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein. Centronics is a registered trademark of Centronics Data Computer Corp. Microsoft is a registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation.
TOSHIBA Barcode Printer B-852 SERIES Owner's Manual
Waste Recycling information for users: Following information is only for EU-member states: The use of the crossed-out wheeled bin symbol indicates that this product may not be treated as general household waste. By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
Safety Summary ENGLISH VERSION EO1-33055 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment.
Safety Summary ENGLISH VERSION EO1-33055 If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorised TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or electric shock. Ensure that the equipment is Connect a properly grounded. Extension grounding wire. cables should also be grounded.
ENGLISH VERSION EO1-33055 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW.......................................................................................................... E1-1 1.1 1.2 1.3 1.4 1.5 1.6 2. Introduction.................................................................................................................... E1-1 Features ........................................................................................................................ E1-1 Unpacking......................
ENGLISH VERSION EO1-33055 3. ON LINE MODE...................................................................................................................... E3-1 3.1 3.2 3.3 4. MAINTENANCE ..................................................................................................................... E4-1 4.1 5. Operation Panel............................................................................................................. E3-1 Operation.............................................
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33055 1.1 Introduction 1. PRODUCT OVERVIEW 1.1 Introduction Thank you for choosing the TOSHIBA B-852 series label/tag printer. This Owner’s Manual contains from general set-up through how to confirm the printer operation using a test print, and should be read carefully to help gain maximum performance and life from your printer. For most queries please refer to this manual and keep it safe for future reference.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33055 1.4 Accessories 1.4 Accessories When unpacking the printer, please make sure all accessories are supplied with the printer. Start-up CD-ROM (1 pc.) • • • • • Bar code print application (Bartender ultra lite) Windows Driver Owner’s Manual Specifications (Programming, Key operation, etc.) Product information (Catalogue) Power Cord QQ (1 pc.) Power Cord QP (1 pc.) Print Head Cleaner (1 pc.) Supply Holder Unit (1 pc.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33055 1.5 Appearance 1.5 Appearance The names of the parts or units introduced in this section are used in the following chapters. 1.5.1 Dimensions 10.4 (265) Depth is 470 mm (18.5 inches) when the optional Cutter Module is installed on the printer. 10.4 (265) NOTE: 7.1 (181) 15.2 (385) 16.8 (427) Dimensions in inches +(mm) 1.5.2 Front View LCD Message Display Top Cover Operation Panel Caution Label Head Pressure Adjust Lever Media Outlet 1.5.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33055 1.5 Appearance 1.5.4 Operation Panel LCD Message Display ON LINE LED (Green) POWER LED (Green) ERROR LED (Red) [PAUSE] key [RESTART] key [FEED] key Please see Section 3.1 for further information about the Operation Panel. 1.5.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33055 1.6 Options 1.6 Options Option Name Cutter module Expansion I/O interface board Serial Interface board Wireless LAN board Real time clock Type B-7208-QM-R B-SA704-IO-QM-R Description A stop and cut swing cutter. Installing this board in the printer allows a connection with an external device with the exclusive interface, such as the keyboard module. B-SA704-RS-QM-R Installing this PC board provides an RS232C interface port.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2. PRINTER SETUP 2. PRINTER SETUP This section outlines the procedures to setup your printer prior to its operation. The section includes precautions, loading media and ribbon, connecting cables, setting the operating environment of the printer, and performing an online print test. Setup Flow Procedure Installation After referring to the Safety Precautions in this manual, install the printer on a safe and stable location.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.1 Installation 2.1 Installation To insure the best operating environment, and to assure the safety of the operator and the equipment, please observe the following precautions. • Operate the printer on a stable, level, operating surface in a location free from excessive humidity, high temperature, dust, vibration or direct sunlight. • Keep your work environment static free. Static discharge can cause damage to delicate internal components.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.2 Assembling the Accessories 2.2 Assembling the Accessories The following procedure outlines the steps required to assemble the Supply Holder Frame and attach the frame to the B-852 printer in preparation for loading the media. 2.2.1 Assembling the Supply 1. Assemble the Supply Holder Frame (L) and Supply Holder Frame (R) to the Supply Holder Base using the two M-4X6 Wing Bolts supplied, Holder Frame as shown below.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.3 Connecting the Power Cord 2.3 Connecting the Power Cord CAUTION! 1. Make sure that the printer power switch is turned to the off position before connecting the power cord to prevent possible electric shock or damage to the printer. 2. Use only the power cord supplied with the printer. Use of any other cord may cause electric shock or fire. 3. Connect the power cord to a three-prong outlet only, with the third prong being a good ground (earth) connection. 1.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.4 Loading the Media 2.4 Loading the Media The following procedure will outline the steps required to install the media onto the Supply Holder Unit and adjust its position in the Supply Holder Frame at the rear of the B-852 printer. The procedure will then show the steps to properly load the media into the printer so that it feeds straight and true through the printer. 2.4.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.4 Loading the Media 2.4.1 Installing the Media The diagram below, and the steps that follow, show the procedures for onto the Supply Holder installing the Media onto the Supply Shaft and reassembling the Supply Holder Unit. Be sure to follow the step-by-step procedure exactly or the Unit (Cont.) auto centering mechanism may not work properly. WARNING! If you turn the Removable Supply Holder side down after loading the media, the media may drop by weight.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.4 Loading the Media 2.4.2 Installing the Supply Holder Unit onto the Supply Holder Frame 1. Insert the assembled Supply Holder Unit into the rear notches of the Supply Holder Frame as shown in the diagram below. Rear Notch NOTE: Make sure that the brass bushings of the Supply Shaft are seated into the notches so that the entire Supply Holder Unit rotates smoothly.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.4 Loading the Media 2.4.3 Loading Media into the 2. Release the Print Head Block by pressing down on the Head Block Release Lever c as shown below. Printer (Cont.) 3. Raise the Print Head Block to its fully open position as shown by the arrow d in the above diagram. WARNING! Print Head Block 1. The Print Head may become hot. Do not touch the Print Head. 2. Risk of injuries. Do not touch moving parts.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.4 Loading the Media 2.4.3 Loading Media into the 10. After loading the media, don’t forget to move the Supply Holder Unit to the forward notch of the Supply Roll Frame as shown below. Printer (Cont.) 11. If you are using labels or thick tag paper, then it may be necessary to increase the head pressure by lowering the Head Pressure Adjust Lever in the figure below.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.5 Setting Sensor Positions 2.5 Setting Sensor Positions After loading the media, as outlined in the previous paragraphs, it will usually be necessary to set the Media Sensors used to detect the print start position for label or tag printing. 2.5.1 Setting the Feed Gap Sensor 1. With the Print Head Block raised as described in section 2.4.3, pass the labels under the Upper Sensor Ass’y as shown in the figure below. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.6 Loading the Ribbon 2.6 Loading the Ribbon WARNING! • The Print Head may become hot. Do not touch the Print Head. • The Top Cover can be opened during the operation for control purposes only. It should be closed during normal operation. • Risk of injuries. Do not touch moving parts. Disconnect the mains before maintenance of ribbon and media. 1. Raise the Top Cover and release and raise the Print Head Block as described in section 2.4.3, steps 1 and 2. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.7 Connecting the Cables to Your Printer 2.7 Connecting the Cables to Your Printer CAUTION! Do not directly connect the LAN cable wired outside of a building to the LAN port provided on this product, as the LAN port on this product is intended for indoor connection. To connect such LAN cable to the product, be sure to use any communication equipment, like a router, a hub, or a modem which is located within the same building as the product.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.8 Turning the Printer ON/OFF 2.8 Turning the Printer ON/OFF When the printer is connected to your host computer it is good practice to turn the printer ON before turning on your host computer and turn OFF your host computer before turning off the printer. 2.8.1 Turning ON the Printer 1. To turn ON the printer power, press the power switch as shown in the diagram below. Note that ( ) is the power ON side of the switch.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9 on the settings of your host computer or an interface Setting an Operating Depending used, it may be necessary to change the printer parameter settings. Environment LCD Message Display to be Follow the procedures described below to change the printer parameter settings in the System Mode to correspond to your environment. NOTE: Incorrect settings can cause the printer to function erroneously.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting While “<2>PARAMETER SET” is displayed on the LCD Message Display, press the [PAUSE] key to enter the Parameter Setting Mode. The Parameter Setting Mode contains the following sub menus. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: Be careful if the printer is turned off without pressing the [PAUSE] key, the selected value does not become effective. (1) Character Code Selection This parameter is to choose a character code used for printing. Printed characters differ depending on a chosen character code and font.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (3) Baud Rate Selection This parameter is to choose a baud rate of the RS-232C interface. When the printer communicates with a host computer by serial interface, be sure to match the setting with the host. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. SPEED 9600bps Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTES: 1. When using the hardware flow control, the control signals and data must be in pairs between the printer and the PC. Printer Host → RD TD ←TD RD → CTS RTS ←RTS CTS → DTR DSR ←DSR DTR Refer to the RS-232C connector’s pin layout in APPENDIX 2. Check if the printer and the PC is properly connectable with your cable 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (8) LCD Language Selection This parameter is to choose a language in which the LCD message is displayed. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. LCD ENGLISH Use the [FEED] or [RESTART] key to select a desired option. ENGLISH [RESTART] ITALIAN JAPANESE SPANISH [FEED] DUTCH FRENCH GERMAN After selecting a language, press the [PAUSE] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) When ON is selected, pressing the [PAUSE] key will result that the LCD Message Display shows the stop position fine adjustment value setting screen. POSITION +0.0mm POSITION +5.0mm [RESTART] POSITION +0.0mm [FEED] POSITION -5.0mm [FEED] key: Pressing the [FEED] key one time causes a –0.1mm change, up to –5.0 mm. [RESTART] key: Pressing the [RESTART] key one time causes a +0.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) After setting the control code for Control Code 1, press the [PAUSE] key to show the CONTROL CODE2 screen. In a same manner, press the [PAUSE] key after setting the control code for Control Code 2 to display the CONTROL CODE3 screen. CONTROL CODE1 [PAUSE] CONTROL CODE2 [PAUSE] CONTROL CODE3 Press the [PAUSE] key after setting the control code for Control Code 3.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: Kanji code selection is not supported by the QQ/QP model as the Kanji ROMs are not installed. (12) KANJI Code Selection This parameter is to choose a KANJI code. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. KANJI CODE TYPE1 Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTES: 1. It will take about 2 seconds to perform an Auto Print Head check. 2. It is recommended that this function should be activated when high quality printing such as bar codes printing is required. Otherwise, choose OFF. 3. When a broken element is found, the printer stops, displaying “HEAD ERROR”.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: When “WEB PRINTER ON” is selected, the status of the printer connected in a network can be checked through the Web browser. (16) Web Printer Function Selection This parameter is to choose whether to use the printer as a web printer. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (18) Expansion I/O Interface Type Selection This parameter is to choose a type of the Expansion I/O interface operating mode. This parameter should be set depending on the expansion I/O control specification of the device to be connected via the expansion I/O interface. For details, refer to the External Equipment Interface Specification.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (20) Label End/Ribbon End Selection This parameter is to choose a printing process when a label end or ribbon end is detected. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. LBL/RBN END TYP1 Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.2 Dump Mode Setting While “<4>DUMP MODE” is displayed on the LCD Message Display, press the [PAUSE] key to enter the Dump Mode. In the Dump Mode, data in the receive buffer are printed. Data are expressed in hexadecimal values. This operation allows the user to verify programming commands or debug the program. When “<4>DUMP MODE” appears, press the [PAUSE] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.2 Dump Mode Setting (Cont.) Print Conditions • Printing width: 3.9 inches (100 mm) • Sensor selection: None • Print speed: 4”/sec. • Printing mode: Depends on the selection in use. • 16 bytes/line • Data is printed in the order from the new one to the old one. • Data specified by the receive buffer write pointer will be printed in boldface.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.3 BASIC Expansion Mode While “<5>EXPAND MDOE” is displayed on the LCD Message Display, press the [PAUSE] key to enter the BASIC Expansion Mode. In the BASIC Expansion Mode, it is possible to execute the BASIC expansion mode program under the following conditions. NOTE: For the BASIC enable setting mode, refer to the B-852 Series Key Operation Specification stored in the CD-ROM.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.4 Automatic Calibration While “<6>AUTO CALIB” is displayed on the LCD Message Display, press the [PAUSE] key to enter the Automatic Calibration Mode. In the Automatic Calibration Mode, whether to activate the automatic calibration at a power on time or not is selectable.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.5 LAN Setting While “<7>LAN” is displayed on the LCD Message Display, press the [PAUSE] key to enter the LAN Setting Mode. In the LAN Setting Mode, whether to enable the LAN communication and SNMP or not is selectable. When “<7>LAN” appears, press the [PAUSE] key. ON SNMP ON Use the [FEED] or [RESTART] key to select a desired option. OFF [RESTART] ON SNMP ON [FEED] ON SNMP OFF LAN is disabled.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.6 Real Time Clock Setting While “<8>RTC SET” is displayed on the LCD Message Display, press the [PAUSE] key to enter the Real Time Clock Setting Mode. NOTE: The Real Time Clock Setting is effective only when an optional Real Time Clock, B-SA704-RTC-QM-R, is installed. The Real Time Clock Setting Mode contains the following sub menus. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.6 Real Time Clock Setting (3) Low Battery Check Setting This parameter is to choose whether to activate the low battery check (Cont.) function or not. NOTE: 1. Be sure to load the battery and set the low battery check function to ON whenever the real time clock is used. If the battery is not loaded or the battery voltage is low, the real time clock data is erased at the power off time. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.7 IP Address Setting (TCP/IP) Power OFF When the printer is connected to a PC through TCP/IP by using a LAN cable, it is necessary to set an IP address in the System Mode for system administrators. The System Mode for system administrators consists of the following menus. While holding down the [FEED] and [PAUSE] keys, turn on the printer. <1>DIAG. Vx.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.7 IP Address Setting (TCP/IP) (Cont.) In this section, how to set the IP address is described. First, you need to access the System Mode for system administrators. 1. While holding down the [FEED] and [PAUSE] keys, turn on the printer. 2. When “<1>DIAG” appears on the LCD Message Display, release the [FEED] and [PAUSE] keys. Now, the printer is in the System Mode for system administrators. 3.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.7 IP Address Setting (TCP/IP) (Cont.) (1) Printer IP Address This parameter is to set an IP address. PRINTER IP ADRES NOTES: 1. Set each 3-digit value by using the [RESTART] or [FEED] key. [RESTART] key: Increment [FEED] key: Decrement Range: 0 to 255 2. Press the [PAUSE] key to move the cursor to the next 3-digit value. 3. After the last 3-digit value is set, press the [PAUSE] key to go to Gateway IP Address Setting.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.7 IP Address Setting (TCP/IP) (Cont.) (3) Subnet Mask This parameter is to set a Subnet Mask. SUBNET MASK NOTE: After the last 3-digit value is set, press the [PAUSE] key to go to Socket Port Setting. [PAUSE] 255 . 255 . 255 . 000 [PAUSE] 255 . 255 . 255 . 000 [PAUSE] 255 . 255 . 255 . 000 [PAUSE] 255 . 255 . 255 .
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.7 IP Address Setting (TCP/IP) (Cont.) NOTE: Pressing the [PAUSE] key while “DHCP ON” is displayed allows you to set a DHCP client ID. (5) DHCP This parameter is to enable DHCP. DHCP [PAUSE] DHCP [RESTART] or [FEED] OFF DHCP ON [PAUSE] DHCP CLIENT ID (6) DHCP Client ID This parameter is to set a DHCP client ID. DHCP CLIENT ID [PAUSE] 1. 2. 3. 4.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.9 Setting an Operating Environment 2.9.7 IP Address Setting (TCP/IP) (Cont.) (7) DHCP Host Name This parameter is to set a DHCP host name. DHCP HOST NAME NOTE: After the 16th byte of the DHCP host name is set, press the [PAUSE] key. At this time, the display will turn to “<7>IP ADDRESS”. [PAUSE] MODE ASCII [PAUSE] Enter a character or a value for each of 1st byte to 16th byte sequentially using the [FEED] or [RESTART] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers 2.10 Installing the Printer Drivers 2.10.1. Introduction This manual describes how to install the TOSHIBA printer driver for the TOSHIBA bar code printer on your Windows host computer; install and delete the printer driver, the procedure for adding the LAN port, cautions and limitations. The examples provided here illustrate the procedure for installing the printer driver version V7.0 for the B-SA4T series. 2.10.2.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers 2.10.3. Installing the Printer Driver The installation procedure differs depending on the interface connected to the printer and the operation system you are using. Please install the printer driver by performing the appropriate procedure. If the previous version of the printer driver has been installed on your host computer , be sure to uninstall it before you install this printer driver. (Refer to Section 2.10.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers Windows 98/Me (1) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (2) Double-click on the “Add Printer” icon. The Add Printer Wizard runs. Click on the [Next] button. (3) Select “Local printer”, then click on the [Next] button. The screen listing “Manufacturers and Printers” is displayed. (4) Click on the [Have Disk…] button. The “Install From Disk” dialog box is displayed.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (6) The screen to select the existing installed printer driver or use the new one, is displayed. Select “Replace existing driver”, then click on the [Next] button. If you install the printer driver for the first time, this screen is not displayed. (7) Select the port to be used for printing from the “Available ports” list, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers Windows 2000/XP (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (3) Double-click on the “Add Printer” icon. The Add Printer Wizard runs. Click on the [Next] button. (4) Select “Local printer”.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (9) The “Use Existing Driver” screen is displayed. Select “Replace existing driver”, then click on the [Next] button. If you install the printer driver for the first time, this screen is not displayed. (10) Change the printer name if necessary, and select whether or not you use the printer as the default printer (“Yes” or “No”). Click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (2) USB INTERFACE Installation starts by the operating system’s plug-and-play function. Windows 98/Me (1) Turn the printer ON, then connect it to your host computer with the USB cable. The “New Hardware Found” dialog box is displayed, and “USB Device” is detected. (2) After a while, the “Add New Hardware Wizard” dialog box is displayed. Select “Specify the location of the driver (Advanced)”, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (3) Select “Search for the best driver for your device. (Recommended)”. Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver” folder, then click on the [Next] button. (4) Check to see that the “USB Printing Support” driver is detected, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (5) When the screen which indicates the USB Printing Support driver has been installed, is displayed, click on the [Finish] button. (6) After a while, “TEC B-SA4T” is detected as a new hardware. (7) The “Add New Hardware Wizard” dialog box is displayed. Select “Specify the location of the driver (Advanced)”, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (8) Select “Search for the best driver for your device. (Recommended)”. Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver” folder, then click on the [Next] button. (9) Check to see that the “TEC B-SA4T” driver is detected, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (10) Change the printer name if necessary, and select whether or not you use the printer as the default printer (“Yes” or “No”). Click on the [Finish] button. (11) When the screen, which indicates TEC B-SA4T has been installed, is displayed, click on the [Finish] button. (12) When installation is completed, the new printer icon is added in the “Printers” folder.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers Windows 2000/XP NOTE: When plug-and-play printer installation in progress is stopped, be sure to delete the printer detected and displayed on the “Device Manager” tab of the “System Properties” dialog box. (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Turn the printer ON, then connect it to your host computer with the USB cable.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (6) Select “Install from a list or specific location (Advanced)”, then click on the [Next] button. (7) Select “Search for the best driver in these locations”. Mark the “Include this location in the search” checkbox, then click on the [Browse] button. Specify the “\driver” folder in the CD-ROM, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers (8) When the dialog box below is displayed, click on the [Continue Anyway] button. (9) When the “Completing the Found New Hardware Wizard” screen is displayed, click on the [Finish] button. (10) When installation is completed, the new printer icon is added in the “Printers” folder.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers 2.10.4. Uninstalling the Printer Driver NOTE: Before uninstalling the printer driver, be sure to complete all of printing, the status monitor, and properties settings. Windows 98/ME (1) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (2) Right-click on the printer driver icon to be deleted, then select “Delete”. The confirmation message is displayed. (3) Click on the [Yes] button to delete.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers 2.10.5 Adding/Deleting a LAN Port To use the LAN interface, first, you have to make the following settings in “<7> IP ADDRESS” in the system mode of the printer. (Refer to TOSHIBA TEC support representative.) • Set the printer IP address (“PRINTER IP ADRES”), the gateway IP address (“GATEWAY IP ADRES”), and subnet mask (“SUBNET MASK”). • Set the port number (“SOCKET PORT”).
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers Windows 2000/XP (1) Right-click on the printer icon. Select “Properties” to open the printer “Properties” dialog box. (2) Select the “Ports” tab, and click on the [Add Port…] button. The “Printer Ports” dialog box is displayed. (3) Select “Seagull Scientific TCP/IP Port” from the “Available Printer Ports” list, then click on the [OK] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers 2.10.6 Cautions (1) Printer Driver Upgrades • To upgrade the printer driver to this version, uninstall the previous version of the printer driver, before installing this printer driver. • Be sure to restart your host computer, after you upgrade the printer driver. • When your operating system is Windows 98, or Windows Me, be sure to restart your host computer, after you uninstall the previous version of the printer driver.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.10 Installing the Printer Drivers 2.10.7 Using the Printer Driver For how to use the Printer Driver, please refer to the Help for Windows Printer Drivers screen. 1) Open the Properties screen of the Printer Driver. 2) Clicking on the About tab causes the following screen to appear. Click on the [Help] button. About tab [Help] button 3) The Help for Windows Printer Drivers screen appears. This screen will provide how to use the printer driver.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.11 Print Test 2.11 Print Test After your operating environment has been set, perform a print test. 1. Perform a print test by using the Printer Driver or an Issue Command. The printer driver’s Properties screen allows you to set the communication conditions, media size, and other printing conditions in accordance with your operating environment. For details, refer to the Help for the Windows Printer Drivers screen.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.11 Print Test 2.11 Print Test (Cont.) When using an optional Cutter Module It is necessary to set the issue mode, cut position, etc. for the Printer Driver or TPCL (TEC Printer Command Language) in accordance with your printing condition. For details of the TPCL, refer to the B-852 Series External Equipment Interface Specification stored in the CD-ROM. Regarding how to use the Printer Driver, refer to the Help for the Windows Printer Drivers screen.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment This section describes how to fine adjust a print start position, cut/strip position, reverse feed amount, print tone, and ribbon motor torque. When a fine adjustment is required, such as print start position, print tone, etc, follow the procedure below. 1. Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Print Start Position Fine Adjustment FEED ADJ.+10.0mm FEED ADJ.+50.0mm NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –50.0 mm. Pressing the [RESTART] key one time causes a +0.1mm change, up to +50.0 mm. [RESTART] FEED ADJ.+49.9mm FEED ADJ.+0.1mm FEED ADJ.+0.0mm FEED ADJ.-0.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Cut Position Fine Adjustment CUT ADJ. +10.0mm NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –50.0 mm. Pressing the [RESTART] key one time causes a +0.1mm change, up to +50.0 mm. CUT ADJ.+50.0mm [RESTART] CUT ADJ.+49.9mm CUT ADJ.+0.1mm CUT ADJ.+0.0mm CUT ADJ.-0.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Reverse Feed Amount Fine Adjustment BACK ADJ. +5.0mm NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –9.9 mm. Pressing the [RESTART] key one time causes a +0.1mm change, up to +9.9 mm. BACK ADJ.+9.9mm [RESTART] BACK ADJ.+9.8 mm BACK ADJ.+0.1mm BACK ADJ.+0.0mm BACK ADJ.-0.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) X Coordinate Fine Adjustment X ADJUST +5.0mm NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –99.9 mm. Pressing the [RESTART] key one time causes a +0.1mm change, up to +99.9 mm. X ADJUST +99.9mm [RESTART] X ADJUST +99.8mm X ADJUST +0.1mm X ADJUST +0.0mm X ADJUST -0.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Print Tone Fine Adjustment Thermal Transfer Print TONE ADJ. +3 NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –1 tone change, up to –10 tones. Pressing the [RESTART] key one time causes a +1 tone change, up to +10 tones. TONE ADJ. +10 [RESTART] TONE ADJ. +9 TONE ADJ.
2. PRINTER SETUP ENGLISH VERSION EO1-33055 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Ribbon Motor Voltage Fine Adjustment When the ribbon is slack or wrinkled and printing is affected, fine adjust the ribbon motor torque by using the following procedure. Take-up Motor (RBN ADJ ) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –1 step change, up to –15 steps.
2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting 2.13 Threshold Setting To maintain a constant print position the printer uses the media sensor to detect a print start position according to the difference of voltage between a print area and a gap or black mark. When the media is pre-printed, the darker (or more dense) inks can interfere with this process causing paper jam errors. To get around this problem, first, try an automatic threshold setting.
2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) Manual threshold setting procedure If a paper jam error still occurs even after an automatic threshold setting has been performed, manually set the threshold voltage. To make a threshold value manually set in this section effective, select the Transmissive Sensor (when using manual threshold value) or Reflective Sensor (when using manual threshold value) within software commands or the printer driver. 1.
2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) When using the Black Mark Sensor (1) While “<5>SENSOR ADJ.” is displayed, press the [PAUSE] key until the message appears. The displayed value is a real-time voltage being detected by the Black Mark Sensor. [REF. 3.5V Voltage at a black mark Midpoint (Threshold voltage) Voltage at a print area (2) Measure a voltage at a blank part of media and a black mark, respectively.
2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) Storing a “No Media Level” Voltage The following is how to set a “No media level” voltage that is used to detect a paper end. If a “NO PAPER” is displayed even if the media has not run out yet, this voltage needs to be set again. (1) Remove any media from the Black Mark Sensor/Feed Gap Sensor. (2) A real-time voltages being detected by the lower Black Mark Sensor and Feed Gap Sensor are displayed. [PE]R0.
2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) (3) Press the [PAUSE] key until the target sensor type is displayed. THRESHOLD1.0V Black Mark Sensor [PAUSE] THRESHOLD1.4V Feed Gap Sensor (4) Set a threshold voltage (calculated in Sensor Adjustment Menu) by using the [FEED] or [RESTART] key, as shown below. Threshold voltage = Midpoint between voltage at a print area and voltage at a gap/black mark Feed Gap Sensor Black Mark Sensor THRESHOLD4.
3. ON LINE MODE ENGLISH VERSION EO1-33055 3.1 Operation Panel 3. ON LINE MODE This chapter describes usage and purpose of the keys on the Operation Panel in On Line Mode. When the printer is in On Line Mode and connected to a host computer, normal operation of printing images on labels or tags can be accomplished. 3.1 Operation Panel • The figure below illustrates the Operation Panel and key functions.
3. ON LINE MODE ENGLISH VERSION EO1-33055 3.2 Operation 3.2 Operation When the printer is turned on, the “ON LINE” message appears on the LCD Message Display. It is shown during standby or normal printing. 1. The printer is turned on, standing by, or printing. ON LINE 2. If any error occurs during printing, an error message appears. The printer stops printing automatically. (The number on the right column shows the number of unprinted media.) NO PAPER 125 3. To clear the error, press the [RESTART] key.
4. MAINTENANCE ENGLISH VERSION EO1-33055 4.1 Cleaning 4. MAINTENANCE WARNING! 1. Be sure to disconnect the Power Cord before performing maintenance. Failure to do this may cause an electric shock. 2. To avoid injury, be careful not to pinch or jam your fingers while opening or closing the cover and Print Head Block. 3. The Print Head may become hot. Do not touch the Print Head. 4. Do not pour water directly onto the printer. This chapter describes how to perform normal maintenance.
4. MAINTENANCE ENGLISH VERSION EO1-33055 4.1 Cleaning 4.1.2 Covers and Panels Wipe the Cover and Front Panel with a dry soft cloth. Wipe off dirt with a soft cloth slightly moistened with water. CAUTION! Do not use any volatile solvent including thinner and benzene, as this may cause discoloration or distortion of the cover. 4.1.3 Optional Cutter Module 1. Remove the Plastic Head Screw and to detach the Cutter Cover. WARNING! 1. Be sure to turn the power off before cleaning the Cutter Module. 2.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33055 5.1 Error Messages 5. TROUBLESHOOTING This chapter lists the error messages and possible problems and their solutions. WARNING! If a problem cannot be solved by taking actions described in this chapter, do not attempt to repair the printer. Turn off and unplug the printer. Then contact an authorised TOSHIBA TEC service representative for assistance. 5.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33055 5.1 Error Messages 5.1 Error Messages (Cont.) Error Messages NO PAPER **** Problems/Cause 1. The media has run out. 2. The media is not loaded properly. RIBBON ERROR **** 3. The media is slack. 1. The ribbon is not fed properly. 2. The ribbon has run out. EXCESS HEAD TEMP The print head is overheated. HEAD ERROR There is a problem with the Print Head. POWER FAILURE A momentary power failure has occurred. SYSTEM ERROR 1.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33055 5.2 Possible Problems 5.1 Error Messages (Cont.) Error Messages SYNTAX ERROR LOW BATTERY Other error messages 5.2 Problems/Cause While the printer is in the Download mode for upgrading the firmware, it receives an improper command, for example, an Issue Command. The voltage of the Real Time Clock Battery is 1.9V or less. Hardware or software problems may have occurred. Solutions Turn the printer off, and then on again.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33055 5.2 Possible Problems 5.2 Possible Problems (Cont.) Possible Problems Nothing is printed on the media. Causes 1. The media is not loaded properly. 2. 3. 4. The printed image is blurred. 1. 2. The Cutter does not cut. 1. 2. 3. Solutions 1. Load the media properly. ⇒ Section 2.4. The ribbon is not loaded properly. 2. Load the ribbon properly. ⇒ Section 2.6 A print head is not installed properly. 3. Install the Print Head properly.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33055 5.3 Removing Jammed Media 5.3 Removing Jammed Media CAUTION! Do not scratch the Print Head or Platen using a sharp instrument, as this may cause media feed failure or damage to the printer. This section describes in detail how to remove jammed media from the printer. Remove the jammed media from under the Upper Sensor Ass’y as follows: 1. Open the Top Cover. 2. Push the Head Block Release Lever to release and raise the Print Head Block. 3.
6. PRINTER SPECIFICATIONS ENGLISH VERSION EO1-33055 6. PRINTER SPECIFICATIONS 6. PRINTER SPECIFICATIONS This section describes the printer specifications. Model B-852-TS22-QQ-R Item Dimension (W × D × H) B-852-TS22-QP-R 385 mm × 181 mm* × 243 mm (15.2” × 7.1”* × 9.6”) *: Depth is 16.8” (427 mm) when the supply holder is installed. Weight 34.4 lb (15.6 kg) (Media and ribbon are not included.
6. PRINTER SPECIFICATIONS ENGLISH VERSION EO1-33055 6.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33055 7.1 Media 7. SUPPLY SPECIFICATIONS 7.1 Media Please make sure that the media that will be used is approved by TOSHIBA TEC. The warranty does not apply when a problem is caused by using media that is not approved by TOSHIBA TEC. For information regarding TOSHIBA TEC approved media, please contact a TOSHIBA TEC authorised service representative. 7.1.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33055 7.1 Media 7.1.1 Media Type (Cont.) NOTES: 1. To ensure print quality and print head life use only TOSHIBA TEC specified media. 2. When using the cutter ensure that label length d plus inter-label gap length f exceeds 38 mm. (i.e. label pitch should be greater than 38 mm.) 3. When marking black marks on label rolls, the following requirements must be satisfied.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33055 7.1 Media 7.1.4 Effective Print Area The figure below illustrates the relation between the head effective print width and media width. Out of print range Out of print range 12.6mm 216.8 mm±0.2 (Head Effective Print Range) 12.6mm 242 mm (Max. media width) The figure below shows the effective print area on the media. Area to be detected. 1.5mm Start line 1.5 mm from the left edge of media Media height 15 – 640 mm Guaranteed print area 1.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33055 7.2 Ribbon 7.2 Ribbon Please make sure that the ribbon being used is approved by TOSHIBA TEC. The warranty does not apply to any problem caused by using non-approved ribbons. For information regarding TOSHIBA TEC approved ribbon, please contact a sales representative. Type Width Length Outside Diameter Spool type 120 – 220 mm Recommended width is 120, 160 and 220 mm. 300 m φ72 mm (max.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33055 7.3 Recommended Media and Ribbon Types 7.3 Recommended Media and Ribbon Types (Cont.) Ribbon type Vellum wax ribbon Standard wax ribbon Smear-less ribbon (Wax resin ribbon) Scratch and solvent resistance ribbon Description This ribbon is mainly used for vellum paper and labels. It has a very high ink density to cope with uneven printing surface Good match for coated paper (Matt coat and glossy coat). Good match for coated paper.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33055 APPENDIX 1 MESSAGES AND LEDS APPENDIX 1 MESSAGES AND LEDS Appendix 1 describes the LCD messages displayed on the operation panel. Symbols in the message 1: : The LED is illuminated. ~: The LED is flashing. z: The LED is unlit. 2: ****: the number of unprinted media.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33055 APPENDIX 1 MESSAGES AND LEDS LED Indication No. LCD Message Printer Status POWER ONLINE ERROR 19 SYSTEM ERROR z 20 LAN INITIAL... 21 DHCP INITIAL... z z 22 LOW BATTERY z z 23 Display of error message (See Notes.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33055 APPENDIX 1 MESSAGES AND LEDS NOTES: • If a command error is found in the command received, 16 bytes of the command error, starting from the command code, will be displayed. (However, [LF] and [NUL] will not be displayed.) Example 1 [ESC] T20 E30 [LF] [NUL] Command error The following message appears. T20E30 Example 2 [ESC] XR; 0200, 0300, 0450, 1200, 1, [LF] [NUL] Command error The following message appears.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33055 APPENDIX 2 INTERFACE APPENDIX 2 INTERFACE NOTE: To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements: • In case of a parallel interface cable or serial interface cable, fully shielded and fitted with metal or metallised connector housings. • Keep as short as possible. • Should not be bundled tightly with power cords. • Should not be tied to power line conduits.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33055 APPENDIX 2 INTERFACE Connector: PIN No.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33055 APPENDIX 2 INTERFACE USB interface Standard: Transfer type: Transfer rate: Class: Control mode: Number of ports: Power source: Connector: Conforming to V2.0 Full speed Control transfer, Bulk transfer Full speed (12M bps) Printer class Status with the receive buffer free space information 1 Self power Type B Pin No. 1 2 3 4 Signal VCC DD+ GND Series B Plug LAN Standard: Number of ports: Connector: LED status: IEEE802.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33055 APPENDIX 2 INTERFACE Serial interface (Option: B-SA704-RS-QM-R) Type: Communication mode: Transmission speed: Synchronization: Start bit: Stop bit Data length: Parity: Error detection: Protocol: Data input code: Receive buffer: Connector: RS-232C Full duplex 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 115200 bps Start-stop synchronization 1 bit 1 bit, 2 bit 7 bit, 8 bit None, EVEN, ODD Parity error, Framing error, Overrun error Unprocedure communicat
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33055 APPENDIX 2 INTERFACE Wireless LAN (Option: B-SA704-WLAN-QM-R) Standard: Protocol: Security protocol: Antenna: Parameter setting: Default IP address: Default subnet mask: Conforming to IEEE802.11a, IEEE802.11b, and IEEE802.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33055 APPENDIX 2 INTERFACE Expansion I/O Interface (Option: B-SA704-IO-QM-R) Input Signal Output Signal Connector (External Device Side) Connector (Printer Side) IN0 to IN5 OUT0 to OUT6 FCN-781P024-G/P or equivalent FCN-685J0024 or equivalent Pin Signal I/O Pin Signal I/O 1 IN0 Input FEED Function 13 OUT6 Output 2 IN1 Input PRINT 14 N.C. ----- 3 IN2 Input PAUSE 15 COM1 Common (Power) 4 IN3 Input 16 N.C. ----- 5 IN4 Input 17 N.
APPENDIX 3 PRINT SAMPLES ENGLISH VERSION EO1-33055 APPENDIX 3 PRINT SAMPLES APPENDIX 3 PRINT SAMPLES Font EA3- 1
APPENDIX 3 PRINT SAMPLES ENGLISH VERSION EO1-33055 APPENDIX 3 PRINT SAMPLES APPENDIX 3 PRINT SAMPLES (Cont.
APPENDIX 3 PRINT SAMPLES ENGLISH VERSION EO1-33055 APPENDIX 3 PRINT SAMPLES APPENDIX 3 PRINT SAMPLES (Cont.
APPENDIX 4 GLOSSARIES ENGLISH VERSION EO1-33055 APPENDIX 4 GLOSSARIES APPENDIX 4 GLOSSARIES Bar code Feed gap sensor A code which represents alphanumeric characters by using a series of black and white stripes in different widths. Bar codes are used in various industrial fields: Manufacturing, Hospitals, Libraries, Retail, Transportation, Warehousing, etc. Reading bar codes is a fast and accurate means of capturing data while keyboard entry tends to be slow and inaccurate.
APPENDIX 4 GLOSSARIES ENGLISH VERSION EO1-33055 APPENDIX 4 GLOSSARIES Print speed Threshold setting The speed at which printing occurs. This speed is expressed in units of ips (inches per second). A sensor setting operation to have the printer maintain a constant print position of pre-printed media. Reflective sensor Transmissive sensor See Black mark sensor. See Feed gap sensor. Resolution The degree of detail to which an image can be duplicated.
INDEX ENGLISH VERSION EO1-33055 INDEX INDEX B L Backing paper 7-1 Bar code 6-2, A3-2, A4-1 Batch mode 7-1, A4-1 Black mark 2-10, 7-1, 7-2, A4-1 Black mark length 7-1 Black mark sensor 1-4, 2-10, 2-68, 2-72, 4-1, A4-1 Label 2-9, 7-1, 7-2, A4-1 Label length 7-1 LAN interface 6-2 LCD language 2-19 LCD message display 1-3, 1-4, 3-1, 6-1, A1-2 M C Centronics 1-3, 2-23, A2-1 Cut mode 6-1, 7-1, A4-1 Cut position fine adjustment 2-63 Cutter module 1-1, 1-5, 2-60, 4-2, 6-2, A4-1 Media 2-5, 7-1, 7-5, A4-1 Medi
INDEX ENGLISH VERSION EO1-33055 INDEX S Sensor adjust gear 2-10 Serial interface 1-3, A2-4 Serial interface board 1-1, 1-5, 6-2 Socket port 2-37 Subnet mask 2-37 Supply Holder Frame 1-2, 1-3, 2-3, 2-7 Supply Holder Locking Knob 2-5, 2-6 Supply Holder Unit 1-2, 1-3, 2-5, 2-7 T Tag 2-9, 2-10, 7-1, A4-2 Thermal direct 2-66, 6-1, A4-2 Thermal transfer 2-66, 6-1, A4-2 Transmissive sensor 7-2 U USB 1-3, 2-12, 6-2, A2-3, A4-2 W Web printer 2-24 Wireless LAN 1-1, 1-3, 1-5, 2-12, 6-2, A2-5
M EO1-33055D
