TEC Thermal Printer B-SX5T SERIES Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Manuale Utente Manual do Utilizador
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: • Schallemission: unter 70dB (A) nach DIN 45635 (oder ISO 7779) • Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein. Centronics is a registered trademark of Centronics Data Computer Corp. Microsoft is a registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation.
TEC Thermal Printer B-SX5T SERIES Owner's Manual
Waste Recycling information for users: Following information is only for EU-member states: The use of the crossed-out wheeled bin symbol indicates that this product may not be treated as general household waste. By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
This product is equipped with a wireless communication device, TEC-RFID-US1 (B-9704-RFID-U1-US-R) TEC-RFID-EU1 (B-9704-RFID-U1-EU-R) Please be sure to read the enclosed precaution for handling of wireless communication devices before using this product.
Safety Summary ENGLISH VERSION EO1-33059 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment.
Safety Summary ENGLISH VERSION EO1-33059 Disconnect the plug. Connect a grounding wire. If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorised TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or electric shock. Ensure that the equipment is properly grounded. Extension cables should also be grounded.
ENGLISH VERSION EO1-33059 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW.......................................................................................................... E1-1 1.1 1.2 1.3 1.4 1.5 1.6 2. PRINTER SETUP ................................................................................................................... E2-1 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 3. Installation ...........................................................................................
ENGLISH VERSION EO1-33059 Page 5. TROUBLESHOOTING ........................................................................................................... E5-1 5.1 5.2 5.3 Error Messages ............................................................................................................. E5-1 Possible Problems ......................................................................................................... E5-3 Removing Jammed Media......................................................
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33059 1.1 Introduction 1. PRODUCT OVERVIEW 1.1 Introduction Thank you for choosing the TOSHIBA B-SX5T series thermal printer. This Owner’s Manual contains from general set-up through how to confirm the printer operation using a test print, and should be read carefully to help gain maximum performance and life from your printer. For most queries please refer to this manual and keep it safe for future reference.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33059 1.4 Accessories 1.4 Accessories NOTE: As a power cord is not supplied with this printer, please purchase one that meets each country’s safety standard. For details, refer to APPENDIX 3. When unpacking the printer, please make sure all the following accessories are supplied with the printer. CD-ROM (1 pc.) (P/No.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33059 1.5 Appearance 1.5 Appearance 1.5.1 Dimensions The names of the parts or units introduced in this section are used in the following chapters. 291 (11.5) 460 (18.1) 308 (12.1) Dimensions in mm (inches) 1.5.2 Front View LCD Message Display Top Cover Operation Panel Supply Window Media Outlet 1.5.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33059 1.5 Appearance LCD Message Display 1.5.4 Operation Panel POWER LED (Green) ON LINE LED (Green) ERROR LED (Red) [FEED] key [PAUSE] key [RESTART] key Please see Section 3.1 for further information about the Operation Panel. 1.5.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33059 1.6 Options 1.6 Options Option Name Swing cutter module Rotary cutter module PCMCIA interface board Type B-4205-QM-R A stop and cut swing cutter. B-8204-QM-R Rotary cutter B-9700-PCM-QM-R Built-in LAN interface board USB interface board RFID module B-9700-LAN-QM-R This board enables the use of the following PCMCIA cards. ATA card: Conforming to PC card ATA standard Flash memory card: 1MB and 4MB cards (See Section 2.8.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2. PRINTER SETUP 2. PRINTER SETUP This section outlines the procedures to setup your printer prior to its operation. The section includes precautions, loading media and ribbon, connecting cables, setting the operating environment of the printer, and performing an online print test. Setup Flow Installation Procedure After referring to the Safety Precautions in this manual, install the printer on a safe and stable location. Reference 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.1 Installation 2.1 Installation To insure the best operating environment, and to assure the safety of the operator and the equipment, please observe the following precautions. • Operate the printer on a stable, level, operating surface in a location free from excessive humidity, high temperature, dust, vibration or direct sunlight. • Keep your work environment static free. Static discharge can cause damage to delicate internal components.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.2 Fitting the Fan Filter 2.2 Fitting the Fan Filter When installing the printer, it is important to ensure that the Fan Filter is attached before using the printer. The Fan Filter consists of 2 parts: (1) Filter Pad (2) Filter Retainer To fit the Fan Filter, put the Filter Pad inside the Filter Retainer and simply press into place as shown in the diagram below, ensuring connecting pins are aligned with the connecting holes.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.4 Loading the Media 2.4 Loading the Media WARNING! 1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the moving parts, be sure to load the media once the printer has stopped moving completely. 2. The Print Head becomes hot immediately after printing. Allow it to cool before loading the media. 3. To avoid injury, be careful not to trap your fingers while opening or closing the cover.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.4 Loading the Media 2.4 Loading the Media (Cont.) NOTE: Do not over-tighten the Locking Ring of the Supply Holder. 5. 6. 7. Put the media on the Supply Shaft. Pass the media around the Damper, then pull the media towards the front of the printer. Align the projection of the Supply Holder with the groove of the Supply Shaft, and push the Supply Holder against the media until the media is held firmly in place. This will centre the media automatically.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.4 Loading the Media 2.4 Loading the Media (Cont.) 10. Lower the Print Head Block until it stops. 11. After loading the media, it may be necessary to set the Media Sensors used to detect the print start position for label or tag printing. Setting the Feed Gap Sensor position (1) Remove the Locking Screw that secures the Media Sensor. (2) Manually move the Media Sensor so that the Feed Gap Sensor is positioned at the centre of the labels.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.4 Loading the Media 2.4 Loading the Media (Cont.) 12. There are four issue modes available on this printer. How to set the media for each mode is provided below. Batch mode In the batch mode, the media is continuously printed and fed until the number of labels/tags specified in the issue command have been printed. 1. 2. 3. 4. NOTES: Be sure to set the Selection Switch to STANDARD/ PEEL OFF position.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.4 Loading the Media 2.4 Loading the Media (Cont.) Built-in rewinder mode When the Rewinder Guide Plate is attached, the Take-up Spool can be used as a Built-in Rewinder to take up the printed media. (1) Remove the two Black Screws to detach the Front Plate. Front Plate Black Screw (2) Attach the Rewinder Guide Plate to the Strip Plate with the SMW4x8 sems screws. NOTE: Be sure to set the Selection Switch to REWINDER position.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.4 Loading the Media 2.4 Loading the Media (Cont.) WARNING! The cutter is sharp, so care must be taken not to injure yourself when handling the cutter. CAUTION! 1. Be sure to cut the backing paper of the label. Cutting labels will cause the glue to stick to the cutter which may affect the cutter quality and shorten the cutter life. 2. Use of tag paper when the thickness exceeds the specified value may affect the cutter life.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.5 Loading the Ribbon 2.5 Loading the Ribbon WARNING! 1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the moving parts, be sure to load the ribbon once the printer has stopped moving completely. 2. The print head becomes hot immediately after printing. Allow it to cool before loading the ribbon. 3. To avoid injury, be careful not to trap your fingers while opening or closing the cover.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.5 Loading the Ribbon 2.5 Loading the Ribbon (Cont.) NOTES: 1. Be sure to remove any slack in the ribbon when printing. Printing with a wrinkled ribbon will lower the print quality. 2. The Ribbon Sensor is mounted on the rear of the Print Head Block to detect a ribbon end. When a ribbon end is detected, “NO RIBBON” message will appear on the display and the ERROR LED will illuminate.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.6 Connecting the Cables to Your Printer 2.6 Connecting the Cables to Your Printer The following paragraphs outline how to connect the cables from the printer to your host computer, and will also show how to make cable connections to other devices. Depending on the application software you use to print labels, there are 4 possibilities for connecting the printer to your host computer.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.7 Turning the Printer ON/OFF 2.7 Turning the Printer ON/OFF When the printer is connected to your host computer it is good practice to turn the printer ON before turning on your host computer and turn OFF your host computer before turning off the printer. 2.7.1 Turning ON the Printer 1. To turn ON the printer power, press the Power Switch as shown in the diagram below. Note that ( | ) is the power ON side of the switch.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.8 Inserting the Optional PCMCIA Cards 2.8 Inserting the Optional When the optional PCMCIA Interface Board is installed into the printer, there will be a PCMCIA slot available as shown in the figure below. PCMCIA Cards This allows the use of a Flash Memory type card. The following CAUTION! 1. To protect PC cards, discharge static electricity from your body by touching the metal cabinet of the printer before touching the card. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9 Setting an Operating Environment Depending on the settings of your host computer or an interface to be used, it may be necessary to change the printer parameter settings. Follow the procedures described below to change the printer parameter settings in the System Mode to correspond to your environment. LCD Message Display FEED key NOTE: Incorrect settings can cause the printer to function erroneously.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting While “<2>PARAMETER SET” is displayed on the LCD Message Display, press the [PAUSE] key to enter the Parameter Setting Mode. The Parameter Setting Mode contains the following sub menus. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: Be careful if the printer is turned off without pressing the [PAUSE] key, the selected value does not become effective. (1) Character Code Selection This parameter is to choose a character code used for printing. Printed characters differ depending on a chosen character code and font.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (3) Baud Rate Selection This parameter is to choose a baud rate of the RS-232C interface. When the printer communicates with a host computer by serial interface, be sure to match the setting with the host. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET SPEED 9600bps Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTES: 1. When using the hardware flow control, the control signals and data must be in pairs between the printer and the PC. Printer Host TD → RD RD ← TD RTS → CTS CTS ← RTS DSR → DTR DTR ← DSR Refer to the RS-232C connector’s pin layout in APPENDIX 2. Check if the printer and the PC is properly connectable with your cable 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (8) LCD Language Selection This parameter is to choose a language in which the LCD message is displayed. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET LCD ENGLISH Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) When ON is selected, pressing the [PAUSE] key will result that the LCD Message Display shows the stop position fine adjustment value setting screen. <2>PARAMETER SET POSITION +0.0mm POSITION +5.0mm [RESTART] POSITION +0.0mm [FEED] POSITION -5.0mm [FEED] key: Pressing the [FEED] key one time causes a –0.5mm change, up to –5.0 mm.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: Improper setting of the solenoid type may disable the ribbon saving function. (11) Solenoid Type Selection This parameter is to choose the solenoid type that is actually installed. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET SOLENOID TYPE1 Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (13) Control Code Selection This parameter is to choose a Control Code. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET CODE AUTO Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (14) Strip Wait Status Selection This parameter is to choose when the printer sends a strip wait status (05H) to a host in response to a status request command. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET PEEL OFF STS OFF Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: Kanji code selection is not supported by the QM model as the Kanji ROMs are not installed. (16) KANJI Code Selection This parameter is to choose a KANJI code. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET KANJI CODE TYPE1 Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTES: 1. It takes about 2 seconds to perform an Auto Print Head check. 2. It is recommended that this function should be activated when high quality printing such as bar codes printing is required. Otherwise, choose OFF. 3. When a broken element is found, the printer stops, displaying “HEAD ERROR”.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: When “WEB PRINTER ON” is selected, the status of the printer connected in a network can be checked through the Web browser. (20) Web Printer Function Selection This parameter is to choose whether to use the printer as a web printer. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (22) Ribbon Near End Selection This parameter is to choose the remaining ribbon length where the ribbon near end is detected. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears”. <2>PARAMETER SET RBN NEAR END 70m Use the [FEED] or [RESTART] key to select a desired option. RBN NEAR END 70m Near end is detected when the remaining ribbon is 70m long.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (24) Centronics Interface Selection This parameter is to choose the type of the Centronics interface operating mode. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET CENTRO MODE SPP Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (26) Label End/Ribbon End Selection This parameter is to choose a printing process when a label end or ribbon end is detected. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears. <2>PARAMETER SET LBL/RBN END TYP1 Use the [FEED] or [RESTART] key to select a desired option.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) (28) Reverse Feed Speed Selection This parameter is to choose a reverse feed speed. In the strip issue, the back feed speed of 3”/sec. may cause a shortage of feed amount due to a lack of torque, slippery media surface, etc. In such case, reduce the back feed speed to 2”/sec. to secure the feed amount. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.1 Parameter Setting (Cont.) NOTE: When the installed print head type is changed, this parameter should be also changed accordingly. Failure to do this may affect the print quality or print head life. (30) Print Head Type Selection This parameter is to choose the print head type that is actually installed. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.2 Dump Mode Setting While “<4>DUMP MODE” is displayed on the LCD Message Display, press the [PAUSE] key to enter the Dump Mode. In the Dump Mode, data in the receive buffer are printed. Data are expressed in hexadecimal values. This operation allows the user to verify programming commands or debug the program. When “<4>DUMP MODE” appears, press the [PAUSE] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.2 Dump Mode Setting (Cont.) Print Conditions • Printing width: 3.9 inches (100 mm) • Sensor selection: None • Print speed: 4”/sec. • Printing mode: Depends on the selection in use. • 16 bytes/line • Data is printed in the order from the new one to the old one. • Data specified by the receive buffer write pointer will be printed in boldface.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.9 Setting an Operating Environment 2.9.3 BASIC Expansion Mode While “<5>EXPAND MDOE” is displayed on the LCD Message Display, press the [PAUSE] key to enter the BASIC Expansion Mode. NOTE: For the BASIC enable setting mode, refer to the B-SX4T/SX5T Series Key Operation Specification stored in the CD-ROM. In the BASIC Expansion Mode, it is possible to execute the BASIC expansion mode program under the following conditions.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers 2.10 Installing the Printer Drivers 2.10.1 Introduction This manual describes how to install the TOSHIBA printer driver for the TOSHIBA bar code printer on your Windows host computer; install and delete the printer driver, the procedure for adding the LAN port, cautions and limitations. The examples provided here illustrate the procedure for installing the printer driver version V7.0 for the B-SA4T series. 2.10.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers 2.10.3 Installing the Printer Driver The installation procedure differs depending on the interface connected to the printer and the operation system you are using. Please install the printer driver by performing the appropriate procedure. If the previous version of the printer driver has been installed on your host computer , be sure to uninstall it before you install this printer driver. (Refer to Section 2.10.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers Windows 98/Me (1) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (2) Double-click on the “Add Printer” icon. The Add Printer Wizard runs. Click on the [Next] button. (3) Select “Local printer”, then click on the [Next] button. The screen listing “Manufacturers and Printers” is displayed. (4) Click on the [Have Disk…] button. The “Install From Disk” dialog box is displayed.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (6) The screen to select the existing installed printer driver or use the new one, is displayed. Select “Replace existing driver”, then click on the [Next] button. If you install the printer driver for the first time, this screen is not displayed. (7) Select the port to be used for printing from the “Available ports” list, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers Windows 2000/XP (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (3) Double-click on the “Add Printer” icon. The Add Printer Wizard runs. Click on the [Next] button. (4) Select “Local printer”.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (9) The “Use Existing Driver” screen is displayed. Select “Replace existing driver”, then click on the [Next] button. If you install the printer driver for the first time, this screen is not displayed. (10) Change the printer name if necessary, and select whether or not you use the printer as the default printer (“Yes” or “No”). Click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (2) USB Interface Installation starts by the operating system’s plug-and-play function. Windows 98/Me (1) Turn the printer ON, then connect it to your host computer with the USB cable. The “New Hardware Found” dialog box is displayed, and “USB Device” is detected. (2) After a while, the “Add New Hardware Wizard” dialog box is displayed. Select “Specify the location of the driver (Advanced)”, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (3) Select “Search for the best driver for your device. (Recommended)”. Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver” folder, then click on the [Next] button. (4) Check to see that the “USB Printing Support” driver is detected, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (5) When the screen which indicates the USB Printing Support driver has been installed, is displayed, click on the [Finish] button. (6) After a while, “TEC B-SA4T” is detected as a new hardware. (7) The “Add New Hardware Wizard” dialog box is displayed. Select “Specify the location of the driver (Advanced)”, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (8) Select “Search for the best driver for your device. (Recommended)”. Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver” folder, then click on the [Next] button. (9) Check to see that the “TEC B-SA4T” driver is detected, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (10) Change the printer name if necessary, and select whether or not you use the printer as the default printer (“Yes” or “No”). Click on the [Finish] button. (11) When the screen, which indicates TEC B-SA4T has been installed, is displayed, click on the [Finish] button. (12) When installation is completed, the new printer icon is added in the “Printers” folder.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers Windows 2000/XP NOTE: When plug-and-play printer installation in progress is stopped, be sure to delete the printer detected and displayed on the “Device Manager” tab of the “System Properties” dialog box. (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Turn the printer ON, then connect it to your host computer with the USB cable.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (6) Select “Install from a list or specific location (Advanced)”, then click on the [Next] button. (7) Select “Search for the best driver in these locations”. Mark the “Include this location in the search” checkbox, then click on the [Browse] button. Specify the “\driver” folder in the CD-ROM, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers (8) When the dialog box below is displayed, click on the [Continue Anyway] button. (9) When the “Completing the Found New Hardware Wizard” screen is displayed, click on the [Finish] button. (10) When installation is completed, the new printer icon is added in the “Printers” folder.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers 2.10.4 Uninstalling the Printer Driver NOTE: Before uninstalling the printer driver, be sure to complete all of printing, the status monitor, and properties settings. Windows 98/ME (1) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (2) Right-click on the printer driver icon to be deleted, then select “Delete”. The confirmation message is displayed. (3) Click on the [Yes] button to delete.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers 2.10.5 Adding/Deleting a LAN Port To use the LAN interface, first, you have to make the following settings in “<7> IP ADDRESS” in the system mode of the printer. (Refer to TOSHIBA TEC support representative.) • Set the printer IP address (“PRINTER IP ADRES”), the gateway IP address (“GATEWAY IP ADRES”), and subnet mask (“SUBNET MASK”). • Set the port number (“SOCKET PORT”).
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers Windows 2000/XP (1) Right-click on the printer icon. Select “Properties” to open the printer “Properties” dialog box. (2) Select the “Ports” tab, and click on the [Add Port…] button. The “Printer Ports” dialog box is displayed. (3) Select “Seagull Scientific TCP/IP Port” from the “Available Printer Ports” list, then click on the [OK] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers 2.10.6 Cautions (1) Printer Driver Upgrades • To upgrade the printer driver to this version, uninstall the previous version of the printer driver, before installing this printer driver. • Be sure to restart your host computer, after you upgrade the printer driver. • When your operating system is Windows 98, or Windows Me, be sure to restart your host computer, after you uninstall the previous version of the printer driver.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.10 Installing the Printer Drivers 2.10.7 Using the Printer Driver For how to use the Printer Driver, please refer to the Help for Windows Printer Drivers screen. 1) Open the Properties screen of the Printer Driver. 2) Clicking on the About tab causes the following screen to appear. Click on the [Help] button. About tab [Help] button 3) The Help for Windows Printer Drivers screen appears. This screen will provide how to use the printer driver.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.11 Print Test 2.11 Print Test After your operating environment has been set, perform a print test. 1. Perform a print test by using the Printer Driver or an Issue Command. The printer driver’s Properties screen allows you to set the communication conditions, media size, and other printing conditions in accordance with your operating environment. For details, refer to the Help for the Windows Printer Drivers screen.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.11 Print Test 2.11 Print Test (Cont.) When using a Strip Module or an optional Cutter Module It is necessary to set the issue mode, cut/strip position, etc. for the Printer Driver or TPCL (TEC Printer Command Language) in accordance with your printing condition. For details of the TPCL, refer to the B-SX4T/SX5T Series External Equipment Interface Specification stored in the CD-ROM.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment This section describes how to fine adjust a print start position, cut/strip position, reverse feed amount, print tone, and ribbon motor torque. When a fine adjustment is required, such as print start position, print tone, etc, follow the procedure below. 1. Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Print Start Position Fine Adjustment <3>ADJUST SET FEED ADJ.+10.0mm FEED ADJ.+50.0mm NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.5mm change, up to –50.0 mm. Pressing the [RESTART] key one time causes a +0.5mm change, up to +50.0 mm. [RESTART] FEED ADJ.+49.5mm FEED ADJ.+0.5mm FEED ADJ.+0.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.5mm change, up to –50.0 mm. Pressing the [RESTART] key one time causes a +0.5mm change, up to +50.0 mm. Cut/Strip Position Fine Adjustment <3>ADJUST SET CUT ADJ. +10.0mm CUT ADJ.+50.0mm [RESTART] CUT ADJ.+49.5mm CUT ADJ.+0.5mm CUT ADJ.+0.0mm CUT ADJ.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment • Example of Strip Position Fine Adjustment When setting +3.0 mm Compared with “+0.0mm” position, the stop position after printing is shifted forward. Print Head Label Platen Strip Plate Backing Paper Stop position after printing 3mm When setting +0.0 mm Stop position after printing 3mm When setting –3.0 mm Compared with “+0.0mm” position, the stop position after printing is shifted backward.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.5mm change, up to –9.5 mm. Pressing the [RESTART] key one time causes a +0.5mm change, up to +9.5 mm. Reverse Feed Amount Fine Adjustment <3>ADJUST SET BACK ADJ. +5.0mm BACK ADJ.+9.5mm [RESTART] BACK ADJ.+9.0 mm BACK ADJ.+0.5mm BACK ADJ.+0.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.5mm change, up to –99.5 mm. Pressing the [RESTART] key one time causes a +0.5mm change, up to +99.5 mm. X Coordinate Fine Adjustment <3>ADJUST SET X ADJUST +5.0mm X ADJUST +99.5mm [RESTART] X ADJUST +99.0mm X ADJUST +0.5mm X ADJUST +0.0mm X ADJUST -0.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Print Tone Fine Adjustment Thermal Transfer Print <3>ADJUST SET TONE ADJ. +3 NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –1 tone change, up to –10 tones. Pressing the [RESTART] key one time causes a +1 tone change, up to +10 tones. TONE ADJ. +10 [RESTART] TONE ADJ. +9 TONE ADJ.
2. PRINTER SETUP ENGLISH VERSION EO1-33059 2.12 Position and Print Tone Fine Adjustment 2.12 Position and Print Tone Fine Adjustment (Cont.) Ribbon Motor Voltage Fine Adjustment When the ribbon is slack or wrinkled and printing is affected, fine adjust the ribbon motor torque by using the following procedure. Take-up Motor (RBN ADJ ) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –1 step change, up to –15 steps.
2.PRINTER SETUP ENGLISH VERSION EO1-33059 2.13 Threshold Setting 2.13 Threshold Setting To maintain a constant print position the printer uses the media sensor to detect a print start position according to the difference of voltage between a print area and a gap or black mark. When the media is pre-printed, the darker (or more dense) inks can interfere with this process causing paper jam errors. To get around this problem, first, try an automatic threshold setting.
2.PRINTER SETUP ENGLISH VERSION EO1-33059 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) Manual threshold setting procedure If a paper jam error still occurs even after an automatic threshold setting has been performed, manually set the threshold voltage. To make a threshold value manually set in this section effective, select the Transmissive Sensor (when using manual threshold value) or Reflective Sensor (when using manual threshold value) within software commands or the printer driver. 1.
2.PRINTER SETUP ENGLISH VERSION EO1-33059 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) When using the Black Mark Sensor (1) While “<5>SENSOR ADJ.” is displayed, press the [PAUSE] key until the message appears. The displayed value is a real-time voltage being detected by the Black Mark Sensor. <5>SENSOR ADJ. [REFLECT] 3.5V Voltage at a black mark Midpoint (Threshold voltage) Voltage at a print area (2) Measure a voltage at a blank part of media and a black mark, respectively.
2.PRINTER SETUP ENGLISH VERSION EO1-33059 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) Storing a “No Media Level” Voltage The following is how to set a “No media level” voltage that is used to detect a paper end. If a “NO PAPER” is displayed even if the media has not run out yet, this voltage needs to be set again. (1) Remove any media from the Black Mark Sensor/Feed Gap Sensor. (2) A real-time voltages being detected by the Black Mark Sensor and Feed Gap Sensor are displayed. <5>SENSOR ADJ.
2.PRINTER SETUP ENGLISH VERSION EO1-33059 2.13 Threshold Setting 2.13 Threshold Setting (Cont.) (3) Press the [PAUSE] key until the target sensor type is displayed. <3>ADJUST SET THRESHOLD1.0V Black Mark Sensor [PAUSE] <3> ADJUST SET THRESHOLD1.4V Feed Gap Sensor (4) Set a threshold voltage (calculated in Sensor Adjustment Menu) by using the [FEED] or [RESTART] key, as shown below.
3. ON LINE MODE ENGLISH VERSION EO1-33059 3.1 Operation Panel 3. ON LINE MODE This chapter describes usage of the keys on the Operation Panel in On Line mode. When the printer is in On Line mode and connected to a host computer, the normal operation of printing images on labels or tags can be accomplished. 3.1 Operation Panel • The figure below illustrates the operation panel and key functions.
3. ON LINE MODE ENGLISH VERSION EO1-33059 3.2 Operation 3.2 Operation When the printer is turned on, the “ON LINE” message appears on the LCD Message Display. It is shown during standby or normal printing. 1. The printer is turned on, standing by, or printing. ON LINE B-SX5T V1.0A 2. If any error occurs during printing, an error message appears. The printer stops printing automatically. (The number on the right side shows the remaining number of media to be printed.
4. MAINTENANCE ENGLISH VERSION EO1-33059 4.1 Cleaning 4. MAINTENANCE 1. 2. 3. 4. WARNING! Be sure to disconnect the power cord before performing maintenance. Failure to do this may cause an electric shock. To avoid injury, be careful not to pinch your fingers while opening or closing the cover and print head block. The print head becomes hot immediately after printing. Allow it to cool before performing any maintenance. Do not pour water directly onto the printer.
4. MAINTENANCE ENGLISH VERSION EO1-33059 4.1 Cleaning 4.1.1 Print Head/Platen/ Sensors (Cont.) NOTE: Please purchase the Print Head Cleaner (P/No. 24089500013) from your authorised TOSHIBA TEC service representative. 6. Clean the Print Head Element with a Print Head Cleaner or a cotton swab or soft cloth slightly moistened with alcohol. Pinch Roller Print Head Print Head Element Platen Feed Roller Black Mark Sensor/ Feed Gap Sensor 7.
4. MAINTENANCE ENGLISH VERSION EO1-33059 4.1 Cleaning 4.1.3 Optional Cutter Module The swing cutter and rotary cutter are available as an option. They are WARNING! 1. Be sure to turn the power off before cleaning the Cutter Module. 2. As the cutter blade is sharp, care should be taken not to injure yourself when cleaning. both cleaned in the same way. When removing the Cutter Cover of the rotary cutter unit, remove the screws from the bottom of the cover. 1. 2. 3. 4. 5.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33059 5.1 Error Messages 5. TROUBLESHOOTING This chapter lists the error messages, possible problems, and their solutions. WARNING! If a problem cannot be solved by taking the actions described in this chapter, do not attempt to repair the printer. Turn off and unplug the printer, then contact an authorised TOSHIBA TEC service representative for assistance. 5.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33059 5.1 Error Messages 5.1 Error Messages (Cont.) Error Messages CUTTER ERROR **** Problems/Cause The media is jammed in the cutter. (Only when the cutter module is installed on the printer.) NO PAPER **** 1. The media has run out. 2. The media is not loaded properly. RIBBON ERROR **** 3. The media is slack. The ribbon is not fed properly. NO RIBBON **** The ribbon has run out. REWIND FULL **** The Built-In Rewinder Unit is full.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33059 5.2 Possible Problems 5.1 Error Messages (Cont.) Error Messages FORMAT ERROR FLASH CARD FULL EEPROM ERROR RFID WRITE ERROR RFID ERROR SYNTAX ERROR Other error messages Problems/Cause An error has occurred in formatting the flash ROM. Saving failed because of an insufficient capacity of the flash ROM. Data cannot be read from/written to a backup EEPROM properly.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33059 5.2 Possible Problems 5.2 Possible Problems (Cont.) Possible Problems The printed image is blurred. Causes 1. The ribbon and media are not matched. 2. The Print Head is not clean. The cutter does not cut. 1. The Cutter Cover is not attached properly. 2. The media is jammed in the Cutter. 3. The cutter blade is dirty. The Strip Module does not remove labels from the backing paper. Label stock is too thin or the glue is too sticky. E5- 4 Solutions 1.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33059 5.3 Removing Jammed Media 5.3 Removing Jammed Media CAUTION! Do not use any tool that may damage the Print Head. This section describes in detail how to remove jammed media from the printer. 1. Turn off and unplug the printer. 2. Open the Top Cover. 3. Turn the Head Lever to Free position, then open the Ribbon Shaft Holder Plate. 4. Open the Print Head Block. 5. Remove the ribbon and media.
6. PRINTER SPECIFICATIONS ENGLISH VERSION EO1-33059 6. PRINTER SPECIFICATIONS 6. PRINTER SPECIFICATIONS This section describes the printer specifications. Model B-SX5T-TS22-QM-R Item Dimension (W × D × H) 291 mm × 460 mm × 308 mm (11.5” × 18.1” × 12.1”) Weight 44.1 lb (20 kg) (Media and ribbon are not included.
6. PRINTER SPECIFICATIONS ENGLISH VERSION EO1-33059 6.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33059 7.1 Media 7. SUPPLY SPECIFICATIONS 7.1 Media Please make sure that the media being used is approved by TOSHIBA TEC. The warranty does not apply when a problem is caused by using media that is not approved by TOSHIBA TEC. For information regarding TOSHIBA TEC approved media, please contact a TOSHIBA TEC authorised service representative. 7.1.1 Media Type Two types of media can be loaded for this thermal transfer and direct thermal printer: label or tag.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33059 7.1 Media NOTES: 1. To ensure print quality and print head life use only TOSHIBA TEC specified media. 2. The media length specifications for use of the cutter are: *1: When issuing a label using the swing cutter, label length should be 35.0 mm – (Gap length/2). 3. When marking black marks on the label rolls, they should be marked at the gaps. 4. “On the fly issue” means that the printer can feed and print without stopping between labels. 5.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33059 7.1 Media 7.1.3 Detection Area of the Reflective Sensor The Reflective Sensor is movable from the centre to the left edge of media. The reflection factor of the Black Mark must be 10% or lower with a waveform length of 950 nm. The Reflective Sensor should be aligned with the centre of the Black Mark. Centre of media Sensor should be positioned at the centre of the black mark. Detecting the black marks on the back. Min. 2.0 mm Min.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33059 7.1 Media 7.1.5 RFID Tags Available RFID tag types are different depending on the RFID modules, as follows: B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R • EPC Class 1 • ISO18000-6B B-9704-RFID-H1-QM-R • TAGSYS C210 • TAGSYS C220 • TAGSYS C240 • I-Code • Tag-it • ISO15693 Cautions for using RFID Tags (1) Lift-up of Print Head An RFID tag chip or the print head may be damaged when the print head passes over the chip.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33059 7.1 Media (7) Printing on Bump (Chip/Antenna) Area Embedding an RFID tag in labels creates bumps on the label surface, causing incomplete printing. Uneven printing or incomplete printing can occur easily, especially within 5 mm back and forth, and right and left sides of the RFID-tag embedded area, as shown in the figure below. NOTE: The degree of poor printing quality differs depending on height of a chip/antenna used.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33059 7.2 Ribbon 7.2 Ribbon Please make sure that the ribbon being used is approved by TOSHIBA TEC. The warranty does not apply to any problem caused by using non-approved ribbons. For information regarding TOSHIBA TEC approved ribbon, please contact a TOSHIBA TEC service representative. Type Width Length Outside Diameter Spool type 68 – 134 mm Recommended width is 41, 50, 68, 102, and 134 mm. 600 m φ90 mm (max.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33059 7.4 Care/Handling of Media and Ribbon 7.3 Recommended Media and Ribbon Types (Cont.) Ribbon type Vellum wax ribbon Standard wax ribbon Smear-less ribbon (Wax resin ribbon) Scratch and solvent resistance ribbon Description This ribbon is mainly used for vellum paper and labels. It has a very high ink density to cope with uneven printing surface Good match for coated paper (Matt coat and glossy coat). Good match for coated paper.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33059 APPENDIX 1 MESSAGES AND LEDS APPENDIX 1 MESSAGES AND LEDS Appendix 1 describes the LCD messages displayed on the operation panel. Symbols in the message 1: : The LED is illuminated. ~: The LED is flashing. z: The LED is unlit. 2: ****: the number of unprinted media.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33059 APPENDIX 1 MESSAGES AND LEDS LED Indication No.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33059 APPENDIX 1 MESSAGES AND LEDS NOTES: • If a command error is found in the command received, 16 bytes of the command error, starting from the command code, will be displayed. (However, [LF] and [NUL] will not be displayed.) Example 1 [ESC] T20 G30 [LF] [NUL] Command error The following message appears. T20G30 B-SX5T V1.0A Example 2 [ESC] XR; 0200, 0300, 0450, 1200, 1, [LF] [NUL] Command error The following message appears. XR;0200,0300,045 B-SX5T V1.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33059 APPENDIX 2 INTERFACE APPENDIX 2 INTERFACE NOTE: To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements: • In case of a parallel interface cable or serial interface cable, fully shielded and fitted with metal or metallised connector housings. • Keep as short as possible. • Should not be bundled tightly with power cords. • Should not be tied to power line conduits.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33059 APPENDIX 2 INTERFACE Connector: PIN Signal No.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33059 APPENDIX 2 INTERFACE Serial interface (Standard) Type: Communication mode: Transmission speed: Synchronization: Start bit: Stop bit Data length: Parity: Error detection: Protocol: Data input code: Receive buffer: Connector: RS-232C Full duplex 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 115200 bps Start-stop synchronization 1 bit 1 bit, 2 bit 7 bit, 8 bit None, EVEN, ODD Parity error, Framing error Unprocedure communication ASCII code, European chara
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33059 APPENDIX 2 INTERFACE LAN (Option: B-9700-LAN-QM-R) Physical Layer: Number of ports: Connector: LED status: IEEE802.3 10BASE-T/100BASE-TX 1 RJ-45 Link LED, Activity LED LED Link Link LED (Green) LED Status LAN status ON 10Mbps link or 100Mbps link is detected. OFF No link is detected. * Communication cannot be made while the Link LED is off.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33059 APPENDIX 2 INTERFACE Expansion I/O Interface (Option: B-7704-IO- QM-R) Input Signal Output Signal Connector (External Device Side) Connector (Printer Side) IN0 to IN5 OUT0 to OUT6 FCN-781P024-G/P or equivalent FCN-685J0024 or equivalent Pin Signal I/O Pin Signal I/O 1 IN0 Input FEED Function 13 OUT6 Output 2 IN1 Input PRINT 14 N.C. ----- 3 IN2 Input PAUSE 15 COM1 Common (Power) 4 IN3 Input 16 N.C. ----- 5 IN4 Input 17 N.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33059 APPENDIX 2 INTERFACE RFID (Option) • B-9704-RFID-U1-US Module: Frequency: Output: Available RFID tag: AWID MPR-1510A-RM 902 MHz to 928 MHz (FH-SS (Frequency Hopping Spectrum Spread)) 500 mW EPC Class 0, 1, ISO018000-6B • B-9704-RFID-U1-EU Module: Frequency: Output: Available RFID tag: AWID MPR-1580A-RM 869.
APPENDIX 3 POWER CORD ENGLISH VERSION EO1-33059 APPENDIX 3 POWER CORD APPENDIX 3 POWER CORD When purchasing the power cord: Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your authorized TOSHIBA TEC representative.
APPENDIX 4 PRINT SAMPLES ENGLISH VERSION EO1-33059 APPENDIX 4 PRINT SAMPLES APPENDIX 4 PRINT SAMPLES Font EA4- 1
APPENDIX 4 PRINT SAMPLES ENGLISH VERSION EO1-33059 APPENDIX 4 PRINT SAMPLES APPENDIX 4 PRINT SAMPLES (Cont.
APPENDIX 4 PRINT SAMPLES ENGLISH VERSION EO1-33059 APPENDIX 4 PRINT SAMPLES APPENDIX 4 PRINT SAMPLES (Cont.
APPENDIX 5 GLOSSARIES ENGLISH VERSION EO1-33059 APPENDIX 5 GLOSSARIES APPENDIX 5 GLOSSARIES Bar code Expansion I/O interface A code which represents alphanumeric characters by using a series of black and white stripes in different widths. Bar codes are used in various industrial fields: Manufacturing, Hospitals, Libraries, Retail, Transportation, Warehousing, etc. Reading bar codes is a fast and accurate means of capturing data while keyboard entry tends to be slow and inaccurate.
APPENDIX 5 GLOSSARIES ENGLISH VERSION EO1-33059 APPENDIX 5 GLOSSARIES Pre-printed media Thermal direct printing A type of media on which characters, logos, and other designs have been already printed. A printing method using no ribbon, but thermal media which reacts to heat. The thermal print head heats the thermal media directly, causing print image to be printed on the media.
INDEX ENGLISH VERSION EO1-33059 INDEX INDEX A J Auto ribbon saving 2-11 Jammed media 5-5 B L Backing paper 2-7, 7-1 Bar code 6-2, A5-1 Batch mode 2-7, 7-1, A5-1 Black mark 2-6, 7-1, 7-3, A5-1 Black mark length 7-1 Black mark sensor 2-6, 2-67, 4-2, A5-1 Built-in rewinder 2-8, A5-1 Label 2-4, 7-1, 7-2, A5-1 LAN interface 1-1, 1-5, 2-12, 6-2 LCD language 2-20 LCD message display 1-3, 1-4, 2-15, 3-1, 6-1 C M Media 7-1, 7-7, A5-1 Media pitch 7-1 Media sensor 2-6 Centronics 1-3, 2-12, 2-26, 2-29, 6-2,
INDEX ENGLISH VERSION EO1-33059 INDEX S Serial interface 1-3, 2-12, 6-2, A2-4 Strip mode 2-7, 7-1, A5-2 T Tag 2-4, 7-1, A5-2 Thermal direct 2-63, 6-1, A5-2 Thermal transfer 2-63, 6-1, A5-2 Transmissive sensor 7-2 U USB interface 1-3, 1-5, 2-12, 6-2, A2-3, A5-2 W Web printer 2-26 Wireless LAN 1-1, 1-3, 1-5, 2-12, 6-2, A2-5
M EO1-33059
