C3000D English OM Cov 28/1/07 4:51 pm Page 1 TOSHIBA C3030 X3030 Series
C3000D Eng Euro OM 28/1/07 8:09 pm Page 3 SETTING UP Safety precautions – Some do’s and don’ts for you to be aware of Installation and important information The remote control – an at-a-glance guide Connecting external equipment – a guide to connecting external equipment to the back of the television Connecting a computer – connecting a computer to the back of the television Controls and input connections – switching on the television, standby, using the controls on the television, headphone socket, con
C3000D Eng Euro OM 28/1/07 8:09 pm Page 4 English Safety Precautions This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken to obtain the best results and for safety to be assured. Please read the points below for your own safety. They are of a general nature, intended to help with all electronic consumer products and some points may not apply to the goods you have just purchased.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 5 English Installation and important information Where to install Locate the television away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen. Sturdy tie (as short as possible) Place on a sturdy platform, the mounting surface should be flat and steady.
English C3000D Eng Euro OM 28/1/07 8:09 pm Page 6 The remote control UP Simple at-a-glance reference of your remote control.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 7 English Connecting external equipment Before connecting any external equipment, turn off all main power switches. If there is no switch remove the mains plug from the wall socket. COMPONENT VIDEO (EXT3) SCART 2 (EXT2) SCART 1 (EXT1) CABLE HOLDER *a decoder could tellite be Digital Sa or any other er. compatible decod decoder* FIXING STRAP HDMI™ INPUT SOCKETS MEDIA REC.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 8 English Connecting a computer Before connecting any external equipment, turn off all main power switches. If there is no switch remove the mains plug from the wall socket. the back of your television Audio cable for PC to television connection (not supplied) Computer Mini D-sub 15 pin connector RGB PC cable (not supplied) Conversion adaptor if required (not supplied) Connect the PC cable from the computer to the PC terminal on the back of the television.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 9 English Controls and input connections A wide variety of external equipment can be connected to the input sockets on the side of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 10 English Tuning Digital television for the first time Before switching on the television put your decoder and media recorder to Standby if they are connected and ensure the aerial is connected. To set up the television use the buttons on the remote control as detailed on page 6. 1 Press the button, the LOCAL OPTIONS screen will appear. This screen will appear the first time that the television is switched on and each time the television is reset.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 11 English Digital auto tuning NOTE: As new services are broadcast it will be necessary to re-tune the television in order to view them. You must allow the television to complete the search. Auto tuning When the search is complete the Auto tuning screen will display the total number of services found. Auto tuning will completely re-tune the television and can be used to up date the channel list.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 12 English Digital programme sorting, manual tuning NOTE: When the television is switched off the mode being viewed at the time will automatically be selected when the television is switched back on. Programme sorting 1 The station order may be changed to suit personal preference. Press MENU, the SETUP MENU will appear on screen. 2 Use to move down through the list and highlight Programmes. Press OK.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 13 The Quick Setup feature will tune all analogue channels currently available in the area. To put the television into ATV mode press the A/D button. 1 Select ATV mode. The Quick Setup screen will appear. Manual tuning Prog. Channel 1 C22 BBC1 2 C28 BBC2 3 C25 ITV 4 C32 CH4 5 C68 6 C69 Quick Setup Select your language. Language EXIT English Watch TV OK 2 Using OK. 3 Then press 4 To start Auto tuning press OK.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 14 English Analogue manual tune The television can be tuned-in manually using Manual tuning. For example: if the television cannot be connected to a media recorder/decoder with a SCART lead or to tune-in a station on another System. Use z and x to move across the screen and select any of these Manual Tune options.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 15 8 When your media recorder signal is found, press to move along to Station. With , , and put in the required characters, e.g. VCR. Using Auto tuning fez x x 1 Manual tuning Station 0 I A Store MENU Back C 60 0 English Analogue manual tune continued, Auto tune To set up the television using Auto tuning, press MENU and use or to select the SET UP menu. z x V C R OK 9 10 Watch TV EXIT SET UP Press OK to store.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 16 English Analogue programme skip, sorting programme positions Programme skip Sorting programme positions To prevent certain programmes from being viewed, the programme position can be skipped. The remote control must be removed as the channels will still be available using the number buttons. Programmes can then be watched as normal using the controls on the television, but the television will not show the skipped programme position.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 17 Selecting programme positions English General controls, stereo/bilingual transmissions, time display, sound controls Bass, Treble and Balance To select a programme position use the numbered buttons on the remote control. The sound controls are accessible in digital and analogue modes, as are most of the televisions features. Programme positions can also be selected using P P and P Q.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 18 English Sound controls continued, SRS WOW™ sound effects, dual, stable sound® WOW Bass boost Bass boost enhances the depth of the sound on the TV speakers. The difference will only be noticeable on sound with a strong bass. SRS 3D On FOCUS Off TruBass Off MENU 1 2 In the SOUND menu press to highlight Bass boost. Use or to select On. z x Then press using or e 3 e to highlight Bass boost level and z x adjust to suit your preference.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 19 English Widescreen viewing Depending on the type of broadcast being transmitted, programmes can be viewed in a number of formats. button repeatedly to select between PC, Exact scan, Wide, Super Live 2, Cinema 2, 4:3, Press the Super Live 1, Cinema 1, Subtitle and 14:9. { SUPER LIVE 1 This setting will enlarge a 4:3 image to fit the screen by stretching the image horizontally and vertically, holding better proportions at the centre of the image.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 20 English Widescreen viewing continued 14:9 Use this setting when watching a 14:9 broadcast. WIDE Use this setting when watching a widescreen DVD, widescreen video tape or a 16:9 broadcast (when available). Due to the range of widescreen formats (16:9, 14:9, 20:9 etc.) black bars may be visible on the top and bottom of the screen. Use this setting to view a true 4:3 broadcast. 4:3 FULL HD MODELS ly This option is on watching available when a 1080 source.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 21 English Picture controls Most of the picture controls and functions are available in both digital and analogue modes. To access the required menus when in digital mode: press MENU and using select TV setup, press OK then or to select the desired menu. PLEASE NOTE: features not available in digital mode will be greyed out. To access the required menus when in analogue mode: press MENU and use or to select the desired menu.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 22 English Picture controls continued Picture preferences MPEG NR – Noise Reduction This television offers the choice of personalising the picture to view the different styles available: style. Press When watching a DVD the compression may cause some words or picture elements to become distorted or pixelated. Using the MPEG NR feature reduces this effect by smoothing out the edges.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 23 English Picture controls continued Colour temperature Base colour adjustment Colour Temperature increases the ‘warmth’ or ‘coolness’ of a picture by increasing the red or blue tint. The Base colour adjustment feature allows the adjustment of individual colours to suit personal preference. This can be useful when using an external source. 1 In the Picture settings menu press until Colour Temperature is highlighted.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 24 English Picture controls continued 1 Active Backlight Control Antenna amplifier When Active Backlight Control is activated it will automatically optimise the backlighting levels for dark scenes. If the signal being received by the television is too strong, this may result in picture interference and/or a buzzing sound. Setting Antenna Amplifier to Off reduces the signal strength, and can help to remove the interference.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 25 English Picture controls continued, panel lock 4:3 stretch Side panel adjustment When 4:3 stretch is activated the size switching system changes 4:3 programs into a full screen picture. The Side panel feature lightens or darkens the band each side of the screen when in 4:3 or 14:9 format. This helps prevent image retention of the band and can also make viewing in bright or dark conditions more comfortable. 1 In the FUNCTION menu press 4:3 stretch.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 26 English The timers 5 Programme timer – digital only Auto-start VCR: If your Toshiba media recorder is AV link compatible setting this feature to YES will auto start/stop a recording. This feature will set the television to go to a specific channel at a certain time. It can be used to view a particular programme, or by setting the mode to daily or weekly, can be used to view a series of programmes. 1 Press MENU and MENU.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 27 English Digital on-screen information and Programme Guide When viewing in digital mode, the on-screen information and programme guide give access to programme details for all available channels. Information 1 Guide Select information by pressing i+ , the information screen will appear giving details of the channel and programme currently being viewed.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 28 English Digital settings – parental control In order to prevent viewing of unsuitable films and programmes, channels and menus can be locked. These can then only be accessed with a security code PIN when in digital mode. Setting the PIN 1 Press MENU and Mode This feature locks various menus to prevent the television being retuned or the settings being overridden. x to select the FEATURE MENU. 1 In the PARENTAL CONTROL menu press select Mode.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 29 Selecting favourite programmes Locking programmes Favourite Programmes creates a list of the digital channels that are watched most. Four lists can be created, these can be a mixture of television, text and radio channels. Locked Programmes stops the viewing of digital channels, they can only be accessed by entering the PIN. 1 From the FEATURE MENU press to select Favourite and Locked Programmes.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 30 English Digital settings continued – audio languages, audio output, subtitles, reset tv, common interface Audio languages Subtitles This feature allows a programme or film to be viewed with a choice of soundtrack language, provided they are currently being broadcast. This feature will show subtitles on the bottom of the screen in the selected language provided they are being broadcast. 1 In the SETUP MENU press Options. 2 Press OK, then press Language.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 31 Version Searching for new software This feature can be used to check the version of software currently installed. If preferred, software upgrades can be searched for manually using Search for New Software. 1 From the FEATURE MENU press Software upgrade. Press OK. f or e to select 1 In the SOFTWARE UPGRADE menu press to select Search for New Software.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 32 English PC settings – picture position, clock phase, sampling clock, reset Picture position Sampling clock Connect the PC (as shown in the ‘Connecting a PC’ section) and ensure that a picture is showing on the television screen. The picture position may now be adjusted to suit personal preference. Adjusting the Sampling clock alters the number of pulses per scan, this will clear vertical lines on the screen.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 33 English Input selection and AV connections Defining the INPUT and OUTPUT sockets so that the television recognises connected equipment. See page 7 for a clear view of the back connection recommendations. Most media recorders and decoders send a signal through the SCART lead to switch the television to the correct Input socket. INPUT signal selection This specifies the type of signal going into SCART 2 (EXT2) on the back of the television.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 34 English Input selection and AV connections continued PC audio HDMI1 audio In order to receive sound from a connected PC, plug the audio cable into the back of the television (as shown in ‘Connecting a computer’ section), then use the PC/HDMI1 audio settings.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 35 This television has a multi-page text memory, which takes a few moments to load. It offers two Modes of viewing text – Auto will display Fastext, if available. LIST will store your four favourite pages. The sub-page you are viewing will be highlighted and, as the television loads any additional sub-pages the colour of the numbers will change, indicating that these pages have been loaded.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 36 English Analogue text services – control buttons, Digital interactive services Below is a guide to the functions of the remote control text buttons. T select a page whilst viewing a 8/9 Tonormal picture: To display the index/initial page: Press to access the index/initial page. The one displayed is dependant on the broadcaster. T / , a normal Enter the page number then press picture will be displayed.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 37 English Questions and Answers Below are the answers to some of the most common queries. For more information go to www.toshiba.co.uk Q A Q Q Why is there no sound or picture? A Check the television is not in standby mode. Check the mains plug and all mains connections.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 38 English Questions and Answers Q A Q A Q A Q Q Why is the DTV main menu unavailable? Use the Master PIN code of 1276, then change to a number of your choice. Ensure that no-one else can use the Master PIN by removing the Owner’s Manual. Why are some of the menus locked? Q Lock Menu has been enabled (see 'Parental Controls' page). Q A Q A Q A Why are there vertical stripes on the screen when in PC mode? A The Sampling clock may need adjustment.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 39 Q Q Why are there no analogue text sub-pages? A A There are none broadcast or they have not yet loaded. Press the button to access. (See text section). X continued English Questions and Answers Why are the colours wrong when an NTSC source is played? Connect the source via a SCART lead and play. Select Manual setting from the SET UP menu. Manual setting Q Colour system: Auto.
English C3000D Eng Euro OM 28/1/07 8:09 pm Page 40 Notes For your own records 40
C3000D Eng Euro OM 28/1/07 8:09 pm Page 41 English Information Before connecting any external equipment, turn off all main power switches. If there is no switch remove the mains plug from the wall socket. Connecting a computer Signal information for Mini D-sub 15 pin connector Pin No. Signal name Pin No.
C3000D Eng Euro OM 28/1/07 8:09 pm Page 42 English Specifications and accessories DVB-T Broadcast systems/channels UK UHF 21-68 Broadcast systems/channels PAL-I UHF UK21-UK69 Stereo France VHF 05-10 (VHF 01-05) UHF 21-69 PAL-B/G UHF E21-E69 VHF E2-E12, S1-S41 Visible Screen Size (approx.
