Satellite M100 TOSHIBA Satellite M100 Series User's Manual
Copyright © 2006 by TOSHIBA Corporation. All rights reserved. Under copyright law, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA Satellite M100 Series Portable Personal Computer User's Manual First edition January 2006 Ownership and copyright of music, video computer programs, databases, etc. are protected by the copyright laws.
iLINK is a trademark of Sony Corporation. TruSurround XT, WOW HD, Circle Surround Xtract, SRS and symbol are trademarks of SRS Labs, Inc. TruSurround XT, WOW HD, Circle Surround Xtract, TruBass, SRS 3D, Definition and FOCUS technologies are incorporated under license from SRS Labs, Inc. InterVideo and WinDVD are registered trademarks of the InterVideo Inc. WinDVD Creator is trademarks of the InterVideo Inc. Other trademarks and registered trademarks not listed above may be used in this manual.
■ Before you connect the computer to a power source, ensure that the voltage rating of the AC adapter matches that of the available power source. 115 V/60Hz in most of North and South America and some Far Eastern countries such as Taiwan. 100 V/50Hz in eastern Japan and 100 V/60Hz in western Japan. 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
When using telephone equipment in conjunction with your computer, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: ■ Do not use this product near water, for example, near a bathtub, washing bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. ■ Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
FCC information Model Name: Satellite M100 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EU Declaration of Conformity TOSHIBA declares, that the product: Satellite M100 conforms to the following Standards: This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 89/ 336/EEC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 99/5/EEC in case of implemented telecommunication accessories and the Low Voltage D
Following information is only for EU-member states: The symbol indicates that this product may not be treated as household waste. Please ensure this product is properly disposed as inappropriate waste handling of this product may cause potential hazards to the environment and human health. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Panasonic CD-RW/DVD-ROM UJDA770TBE-W ■ The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
TOSHIBA Samsung Storage Technology Korea Corporation CD-RW/DVD-ROM TS-L462D ■ The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Pioneer DVD Super Multi DVR-K17TBS ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
Panasonic DVD Super Multi UJ-850UTJH-A ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
Hitachi-LG Data Storage, Inc. DVD Super Multi GSA-T10N ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
International Precaution CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT." To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest "AUTHORIZED service station." To prevent direct exposure to the laser beam, do not try to open the enclosure.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision "CTR21"] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer. Japan's Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes. The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.
Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
Instructions for IC CS-03 certified equipment 1. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user's satisfaction.
Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in your modem being operated in a noncompliant manner.
Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
■ The preferred method of dialing is to use DTMF tones (ATDT...) as this is faster and more reliable than pulse (decadic) dialing. If for some reason you must use decadic dialing, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand "Reverse Dialing" standard.
Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.
PC Card overheating Some PC Cards can become hot with prolonged use. Overheating of a PC Card can result in errors or instability in the PC Card operation. Also be careful when you remove a PC Card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30cm be maintained between the computer and a mobile phone in use.
Working environment This product was designed to fulfill the EMC (Electromagnetic Compatibility) requirements for "residential, commercial and light industry environments". The following environment is not approved: ■ Industrial Environments (e.g. environments where a with a mains voltage of 380V threephase is being used).
Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far less than the electromagnetic energy emitted by other wireless devices such as mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers.
Usage Restrictions Do not use the Wireless Products for controlling the following equipment: ■ Equipment directly linked with human life corresponding to the following. ■ Medical equipment such as life support systems, equipment used in operations, etc. ■ Exhaust systems for gases such as poisonous gas etc. and exhaust systems for smoke. ■ Equipment that must be set up in compliance with various laws such as the Fire Services Act, the Construction Standard Act, etc.
Warning Turn OFF the Wireless Communication switch of wireless products in a congested place, such as a crowded commuter train. Keep this product away from a cardiac pacemaker at least 22cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles. Turn OFF the Wireless communication switch inside a medical facility or near medical electric equipment. Do not bring medical electric equipment close to the product.
Satellite M100 Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxx Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxi Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii Chapter 1 Satellite M100 Features Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Special features . . . . . . . . . . . . . . . . . .
Chapter 3 Getting Started Setting up your work space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Connecting the AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Turning on the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Turning off the power. . . . .
Chapter 6 Power and Power-Up Modes Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Care and use of the battery pack . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix A Specifications Appendix B Display Modes Appendix C AC Power Cord and Connectors Glossary xxviii Satellite M100
Satellite M100 Preface Congratulations on your purchase of the Satellite M100 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite M100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Manual contents This manual has ten chapters, three appendixes, a glossary and an index. Chapter 1, Satellite M100 Features, is an overview of the computer's special features, utilities, and options. Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function. Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.
Preface Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Abbreviations On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary. Icons Icons identify ports, dials, and other parts of your computer.
Preface Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read. A note is a hint or advice that helps you make best use of your equipment.
Preface Software The following Windows operating systemand utility software are preinstalled.
Preface xxxiv Satellite M100
Satellite M100 Chapter 1 Satellite M100 Features This chapter identifies the computer's special features, options and accessories. Basic features are described in a separate pamphlet. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA.
Satellite M100 Features Chip Set Intel® 945PM Express Chipset or Intel® 945GM Express Chipset Realtek ALC861 Audio codec TI PCI7412 for Multiple Digital Media Card Slot, IEEE 1394 and PCMCIA controller. Intel® 82562GZ for 10/100Mbps LAN controller or Intel® 82573L for 10M/100M/1Gbps LAN controller Memory The graphics system in your computer may use part of the main system memory for graphics performance and therefore reduce the amount of system memory available for other computing activities.
Satellite M100 Features Video RAM Depending on the model you purchased: Up to 256MB integrated solution and shared with main memory for Mobile Intel® 945GM Express Chipset 64MB or 128MB for local cache for ATI Mobility™ Radeon® X1300 with HyperMemory™ 64MB,128MB or 256MB for local cache for ATI Mobility™ Radeon® X1400 with HyperMemory™ HyperMemory™ VRAM size will vary depending on system memory size.
Satellite M100 Features Power Battery Pack 6-cell Lithium Ion smart battery pack with 43.2 watt capacity (10.8V/4000mAH) or 9-cell Lithium Ion smart battery pack with 64.8 watt capacity (10.8V/6000mAH) or 12-cell Lithium Ion smart battery pack with 92.88 watt capacity (10.8V/8600mAH) (Battery type depends on the model purchased.) Approximately 12 hours or longer charging time to 100% battery capacity with system switched on.
Satellite M100 Features Display 14.1” WXGA TFT screen with a resolution of 1280 horizontal x 800 vertical pixels 14.1" WXGA+ TFT screen with a resolution of 1440 horizontal x 900 vertical pixels Disclaimer (LCD) For more information on the Disclaimer regarding LCD, please refer to the Disclaimers section in Chapter 10. Graphics controller ATI Mobility™ Radeon® X1300/X1400 (Graphics controller chipset depends on the model purchased) The graphics controller maximizes display performance.
Satellite M100 Features Disclaimer (HDD Drive Capacity) For more information on the Disclaimer regarding HDD Drive Capacity, please refer to the Disclaimers section in Chapter 10. 1-6 CD-RW/DVD-ROM drive Some models are equipped with a full-size CDRW/DVD-ROM module that lets you record data to rewritable CD/CD-RWs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adapter. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
Satellite M100 Features DVD Super Multi drive with double layer disc recording support Some models are equipped with a full-size DVD Super Multi drive module with double layer support that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adapter. It reads DVD-ROMs at maximum 8 speed and CDROMs at maximum 24 speed.
Satellite M100 Features Ports (depending on configuration) External monitor 15-pin analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus The computer has 4 Universal Serial Bus (USB) ports that comply with the USB 2.0 standard, which enables data transfer speeds more than 40 times faster than USB 1.1 (which this computer also supports). i.LINK (IEEE 1394) Enables high-speed data transfer directly from external device such as digital video cameras.
Satellite M100 Features Wireless LAN Some computers in this series are equipped with a wireless LAN mini Card that is compatible with other systems that support the 802.11a/g wireless communications standards. It offers frequency selection between 2.4GHz or 5GHz and allows roaming over multiple channels. Bluetooth Some computers in this series are equipped with Bluetooth functionality.
Satellite M100 Features 1-10 System Automatic Sleep/Hibernation This feature automatically places the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time period. You can specify the time period and select either System Sleep or System Hibernate in the Power Options. Keypad Overlay A ten-key pad is integrated into the keyboard. Refer to the Keypad overlay section in Chapter 5, The Keyboard, for instructions on using the keypad overlay.
Satellite M100 Features Fingerprint Adds an additional layer of security to your files by requiring a valid fingerprint to access them. ■ Before entering Sleep mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Sleep mode. The computer or the module could be damaged. ■ Do not remove the battery pack while the computer is in Sleep mode. Data in memory will be lost.
Satellite M100 Features Utilities and Applications This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. DVD Video Player The DVD player is used to play DVD Video media through an on-screen interface and functions.
Satellite M100 Features Satellite M100 Ulead DVD MovieFactory® for TOSHIBA You can edit digital video and make a DVD-Video. FingerPrint utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. (depending on the model purchased.) By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard.
Satellite M100 Features Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory Modules Two memory module can be installed in this computer. Use either PC4200 or PC5400 compatible memory modules. See your TOSHIBA dealer for details 1-14 Battery Pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement.
Satellite M100 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain types of notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
The Grand Tour 2-2 DC IN LED The DC IN LED indicates the computer is connected to the AC adapter and it is plugged into an AC power source. Power LED In normal operating mode, the Power LED is blue. If the system is in Sleep Mode the LED will flash amber, while the LED will be off when the computer is turned off or is in Hibernation Mode. Battery LED The Battery LED indicates the battery's current charge/discharge status. It lights blue when the battery is fully charged.
The Grand Tour Right side The following figure shows the computer's right side. 1 2 1. 2. UNIVERSAL SERIAL BUS (USB) PORTS OPTICAL DISC DRIVE 3 3. 4. 4 OPTICAL DISC DRIVE LED SECURITY LOCK The right side of the computer Satellite M100 Universal Serial Bus (USB) Ports The Universal Serial Bus (USB 2.0 and 1.1 compatible) ports enable USB-equipped devices such as keyboards, mice, hard drives, scanners, and printers to be connected to the computer.
The Grand Tour Left side The following figure shows the computer's left side. 1 2 1. 2. 3. 4. 3 RGB (MONITOR) PORT FAN VENTS UNIVERSAL SERIAL BUS (USB) PORT TV OUT PORT 5. 6. 7. 4 5 6 7 I.LINK (IEEE 1394) PORT MULTIPLE DIGITAL MEDIA CARD SLOT PC CARD SLOT The left side of the computer * The availability of this feature is dependant on the model you purchased. RGB (Monitor) Port This 15-pin port lets you connect an external video display to the computer.
The Grand Tour Back side The following figure shows the computer back panel. 1 2 1. 2. 3. 3 MODEM JACK* DC-IN 15V JACK LAN JACK 4. 4 UNIVERSAL SERIAL BUS (USB) PORTS The back side of the computer * The availability of this feature is depending on the model you purchased. Satellite M100 Modem Jack In regions where an internal modem is installed as standard equipment, this jack lets you use a modular cable to connect the modem directly to a telephone line.
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. 4 1 5 2 3 1. 2. 3. BATTERY PACK BATTERY PACK LOCK EXPANSION MEMORY SOCKET 4. 5. BATTERY PACK LATCH FAN VENT The bottom of the computer Battery Pack The battery pack powers the computer when the AC adapter is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes.
The Grand Tour Front with the display open The following figure shows the front of the computer with the display open. To open the display, push the latch on the front of the display and lift it up. Position the display at a comfortable viewing angle. 1 8 2 9 3 10 4 11 5 5 13 12 6 7 1. 2. 3. 4. 5. 6. 7. DISPLAY SCREEN CD/DVD BUTTON INTERNET BUTTON POWER BUTTON LEFT AND RIGHT SPEAKERS TOUCHPAD TOUCHPAD CONTROL BUTTONS 8. 9. 10. 11. 12. 13.
The Grand Tour CD/DVD Button If you press this button while the computer is on or stand-by, Windows Media Player or WinDVD is launched. Internet Button Press the Internet button to open your default web brower. The button setting can be changed in TOSHIBA Controls properties. Power Button Press the power button to turn the computer's power on and off. There is an LED inside the power button which shines blue when the system is on.
The Grand Tour Next Button Skips forward to the next track, chapter or digital file. Refer to Chapter 4, Operating Basics, for details. (The availability of this function depends on the model you purchased.) Fingerprint Sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a securityenabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented.
The Grand Tour Keyboard Indicators Arrow Mode When the Arrow mode icon lights blue, you can use the keypad overlay (light gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard. Numeric Mode You can use the keypad overlay (light gray labeled keys) for numeric input when the Numeric mode icon lights blue. Refer to the Keypad overlay section in Chapter 5, The Keyboard. Caps Lock The Caps Lock LED lights when you press the Caps Lock key.
The Grand Tour Writable discs This section describes the types of writable discs. Check the specifications for your drive to for the type of discs it can write. Use Record Now! to write compact discs. Refer to Chapter 4, Operating Basics. CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs can be recorded more than once. Use either 1x, 2x, or 4x multi-speed CD-RW discs or high-speed 4x to 10x discs.
The Grand Tour DVD Super Multi drive with double layer disc recording support The full-size DVD super multi drive module lets you record data to rewritable discs as well as run either 12cm (4.72") or 8cm (3.15") discs without using an adapter. The read speed is slower at the center of a disc and faster at the other edge.
The Grand Tour AC adapter The AC adapter converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adapter to a power source and the computer. See Chapter 6, Power and Power-Up Modes, for details. The AC adapter Use of the wrong adapter could damage your computer.
The Grand Tour 2-14 Satellite M100
Satellite M100 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible. ■ The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees Fahrenheit) and the relative humidity should be 20 to 80 percent.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed. ■ Your knees should be slightly higher than your hips.
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency. ■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain. ■ Vary your posture frequently.
Getting Started Connecting the AC adapter Attach the AC adapter when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adapter can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adapter to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer. Opening the display 2. Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. Turning on the power This section describes how to turn on the power.
Getting Started Starting up for the first time When you first turn on the power, the computer's initial screen is the Windows Vista™ Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows Operating System End User License Agreement carefully. Turning off the power The power can be turned off in one of three modes, either Shutdown (Boot) Mode, Hibernation Mode or Sleep Mode.
Getting Started Sleep Mode If you do have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer’s main memory so that, when you turn on the power again, you can continue working right where you left off ■ When the AC adaptor is connected, the computer will go into Sleep Mode according to the settings in the Power Options.
Getting Started Executing Sleep Mode You can enter also Sleep Mode by pressing Fn + F3 - please refer to Chapter 5, The Keyboard, for further details. Youu can enter Sleep Mode in one of three ways: 1. Click Start then click the arrow button ( ) located in the power management buttons ( ), or click the arrow button ( ) and select Sleep from the menu. 2. Close the computer’s LCD display panel.
Getting Started Benefits of Hibernation Mode The Hibernation Mode feature provides the following benefits: ■ Saves Data to the hard disk drive when the computer automatically shutsdown because of a low battery condition. ■ You can return to your previous working environment immediately when you turn on the computer. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature.
Getting Started Restarting the computer Certain conditions require that you reset the computer, for example if: ■ You change certain computer settings. ■ An errors and the computer does not respond you your keyboard commands. If you need to restart the computer, there are three ways this can be achieved: 1. Click Start then click the arrow button ( ) in the power management buttons ( ) and select Restart from the menu. 2.
Getting Started Restoring the preinstalled software from the Product Recovery disc If preinstalled files are damaged, use the Product Recovery disc to restore them. To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. You can not use System Recovery Options if restoring the pre-installed software without System Recovery options. 1.
Satellite M100 Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad, optical disc drives, the internal modem, LAN and wireless LAN. It also provides tips on caring for your computer and on heat dispersal. Using the TouchPad To use the TouchPad, simply move your finger tip across it in the direction you want the on-screen pointer to go. 2 1 1. TOUCHPAD CONTROL BUTTONS 2.
Operating Basics Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using. Do not press on the TouchPad too hard or press a sharp object such as a ball point pen against it. The TouchPad could be damaged. The TouchPad has similar functions to a two-button mouse with a scroll wheel. For some functions, you can tap it instead of pressing a button.
Operating Basics How the Swipe the Finger Using the following steps when swiping fingers for FingerPrint registration or authentication will help to minimize authentication failures: 1. Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you. While lightly touching the sensor, swipe the finger towards you until the sensor surface becomes visible. Ensure the center of the FingerPrint is on the sensor when swiping the finger.
Operating Basics Points to note about the FingerPrint Sensor Please be aware of the following considerations when using the FingerPrint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, FingerPrint recognition problems or a lower FingerPrint recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects. ■ Do not press the sensor strongly.
Operating Basics Observe the following to improve the FingerPrint recognition success rate. ■ Enroll two or more fingers. ■ Enroll additional fingers if recognition failure occurs when using already enrolled fingers. ■ Check the condition of your finger - any conditions which have changed since enrollment, such as injured, rough, extremely dry, wet, soiled, dirty, oily, soaked, swollen fingers, may lower the recognition success rate.
Operating Basics Points to note about the FingerPrint Utility software You are able to backup saved FingerPrint data and information within the PasswordBank by using the import or Export User Data facility under the FingerPrint management software. However, please be aware that any encrypted files cannot be backup within FileSafe using this function - in these instances it is recommended that you backup these files to external media using standard file copy processes.
Operating Basics 3. At the User’s Password screen which is then displayed, you should ensure that the same Windows username is displayed before entering the appropriate password into the Enter you password field. Once this has been done, click Next. 4. At the Hints for FingerPrint Enrollment screen, confirm the message displayed and ensure that there is a check mark in the Run Interactive Tutorial box. Once this has been done, click Next. 5.
Operating Basics FingerPrint Power-on Security General The FingerPrint authentication system can be used to replace the keyboard based password authentication system that is used when the computer is turned on.
Operating Basics FingerPrint Single Sign-On Feature General This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD (Hard Disk Drive) Password) and logging onto Windows using only one FingerPrint authentication when booting up. It is necessary to register the User/BIOS Password and Windows Logon password before using the FingerPrint Power-on Security and this FingerPrint Single Sign On Feature.
Operating Basics Using the internal modem This section describes how to setup the modem and use it to connect to other computer systems. Refer to the computer's online help files and the online help files for your modem software, for more information. The internal modem does not support the voice functions described in the help files. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modem cable from the telephone jack.
Operating Basics 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4. Select a region from the region menu or a telephony location from the submenu. ■ When you click a region it becomes the modem's region selection, and the New Location for telephony will be set automatically.
Operating Basics Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use. Dialing Properties Select this item to display the dialing properties. If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select Japan region mode. It is illegal to use the modem in Japan with any other selection.
Operating Basics Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner. LAN The computer is equipped with networking hardware that supports Ethernet LAN (10megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second and Gigabit Ethernet LAN (1000BASE-T).
Operating Basics 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting the LAN cable To disconnect the LAN cable, follow the steps below. 1. Pinch the lever on the connector in the computer's LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.
Operating Basics Bluetooth wireless technology Bluetooth™ wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. Bluetooth wireless technology has the following features: Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2.4 GHz band, which is license-free and compatible with radio systems in most countries in the world. Radio links You can easily establish links between two or more devices.
Operating Basics 3. Multi User: On Windows Vista™, the use of Bluetooth is not supported in a multiuser environment. This means that, when you use Bluetooth, other users logged onto the same computer will not be able to use its Bluetooth functionality. Product Support: The latest information regarding Operating System support, Language Support or available upgrades can be found on our web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or www.pcsupport.toshiba.
Operating Basics Loading optical disc media To load a disc, follow the steps below. 1. Turn on the power. 2. a. Press the eject button to open the drawer slightly. EJECT BUTTON Pressing the eject button b. Pressing the eject button will not open the drawer when the computer's power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Operating Basics 3. Grasp the drawer gently and pull until it is fully open. Pulling the drawer open 4. Lay the disc, label side up, in the drawer. Inserting a disc Be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction. 5. Press gently at the center of the disc until you feel it click into place. The disc should lie below the top of the spindle, flush with its base. 6. Push the center of the drawer to close it. Press gently until it locks in place.
Operating Basics Closing the drive drawer Removing compact discs To remove the disc, follow the steps below. Do not press the eject button while the computer is accessing the disc drive. Wait for the optical disc indicator to go out before you open the drawer. Also, if the disc is spinning when you open it, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics Buttons The Internet button and the CD/DVD button can be assigned other functions by Button Support Utility. 1. Move mouse cursor and reach the top of desktop screen. The back cards and white cards appear. Click “Button support” white card. 2. "Button Support" white card fully appears. After double click this card, the dialog for changing button function is displayed. 3. Change function of Buttons.
Operating Basics *Writing CDs on a CD-RW/DVD-ROM drive You can use the CD-RW/DVD-ROM drive to write data to CD-R/RW discs. The following applications for writing are preinstalled: Record Now!/DLA, licensed by Sonic Solutions. Important message Before you write or rewrite to CD-R/RW media, read and follow all setup and operating instructions in this section. If you fail to do so, the CD-RW/ DVD-ROM drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used. ■ Be sure to connect the universal AC adapter when you write or rewrite. ■ Be sure to close all other software programs except the writing software.
Operating Basics ■ Do not use shut down/log off and Sleep/Hibernation while writing or rewriting ■ Make sure writing or rewriting is completed before going into Sleep/ hibernation. Writing is completed if you can open the drive tray. ■ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. Do not use an unstable surface such as a stand. ■ Keep mobile phones and other wireless communication devices away from the computer.
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite data. ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM media. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd.
Operating Basics ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it. ■ The actual number of rewrites to CD-RW or DVD-RW/+RW/-RAM is affected by the quality of the disc and the way it is used. ■ There are two types of DVD-R: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. ■ We can support only Format 1 of DVD-R DL.
Operating Basics ■ Do not use hard disk utilities, including those intended to enhance hard disk access speed, as they may cause unstable operation and damage data. ■ Write from the computer's hard disk drive to the CD. Do not try to write from shared devices such as a LAN server or any other network device. ■ Writing with software other than TOSHIBA Disc Creator or Ulead DVD MovieFactory® for TOSHIBA has not been confirmed. Therefore, operation with other software cannot be guaranteed.
Operating Basics When Using Ulead DVD MovieFactory® for TOSHIBA How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click Start -> All Programs -> DVD MovieFactory for TOSHIBA >Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Insert a DVD-RW or DVD+RW disc in Burner. 3. Click Video Disc -> Burn Video to Disc to launch Direct Recording dialog box, choose DVD-Video/+VR to invoke Straight Capture to Disc Page. 4.
Operating Basics ■ Do not operate DVD MovieFactory immediately after turning on the computer. Please wait until all Disc Drive activity has stopped. ■ When recording to a DV-Camcorder, to ensure you capture all of your data, let the camcorder record for a few seconds before you begin recording your actual data. ■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD functions are not supported in this version. ■ While recording video to DVD or tape, please close all other programs.
Operating Basics TOSHIBA Disc Creator Note the following limitations when you use TOSHIBA Disc Ceator: ■ DVD-Video cannot be created using TOSHIBA Disc Ceator ■ DVD-Audio cannot be created using TOSHIBA Disc Ceator ■ You cannot use the TOSHIBA Disc Ceator "Audio CD” function to record music to the DVD-R/-RW or DVD+R/+RW media. ■ Do not use the "Disc Backup" function of TOSHIBA Disc Ceator to copy DVD-Video and DVD-ROM with copyright protection.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Display the setting dialog box by one of the following two steps: ■ Click the setting button ( ) for writing on the main toolbar in the Data CD/DVD mode. ■ Select Setting for writing Data, and go to CD/DVD in the Setting menu. 2. Mark the Verify written data check box. 3. Select File Open or Full Compare mode. 4. Click the OK button.
Operating Basics Discs 1. Store your discs in the container they came in to protect them and keep them clean. If a disk is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2. Do not slide back the disc’s protective metal covering or touch the disc's magnetic surface. FingerPrints may prevent the disc drive from reading data from the disk. 3. Data may be lost if the disc is twisted, bent, or exposed to direct sunlight, or extreme heat or cold. 4. Do not place heavy objects on your discs.
Operating Basics Setting up more than one display You can set up your computer to utilize more than one display, effectively spreading a single desktop screen across two monitors. The Display Properties window allows you to adjust more precisely the relative positioning of the two displays when they are configured as an extended desktop. On the Display Properties window, the two displays can be positioned horizontally, vertically or in any diagonal configuration you wish, as shown below.
Operating Basics Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer. Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Make sure all disk activity has ended before moving the computer. Check the Built-in Hard Disk Drive and optical disc drive indicators on the computer.
Operating Basics 4-34 Satellite M100
Satellite M100 Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region's keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard F1 ... F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + Ctrl to simulate the enhanced keyboard's right Ctrl key. Hotkeys Fn + ESC Mute Turns the volume on and off. Fn + F1 Lock Enters "Lock computer" mode. To restore your desktop, you need to log on again. Fn + F2 Power Plan Mode Displays the power save modes and lets you change the power settings Fn + F3 Sleep This hot key switches the system to Sleep mode. Fn + F4 Hibernate This hot key switches the system to Hibernate mode. Fn + F5 Output Changes displays.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows Vista™. One activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows Vista™ Start menu This key has the same function as the secondary mouse button. Keypad overlay Your computer's keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11 (Numeric mode indicator lights). Now try numeric data entry using the keys below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay (U.S.) Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold down Fn and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use it for cursor and page control. 3. Release Fn to return to normal keyboard operation.
Satellite M100 Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adapter and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power on AC adapter not connected 6-2 Battery capacity is above low battery trigger point • Operates • LED: Battery off DC IN off Battery capacity is below low battery trigger point • Operates • Alarm sounds (this function depends on how the computer is configured) • LED: Battery flashes amber DC IN off Battery capacity exhausted Computer goes into Hibernation or shuts down No battery installed • No operation Power off (no operation) (depending on the Power Option settin
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, DC IN and Power indicators alert you to the computer's operating capability and battery charge status Battery indicator Check the Battery indicator to determine the status of the battery. The following indicator lights indicate the battery status. Flashing amber The battery charge is low. The AC adapter must be connected to recharge the battery Amber Indicates the AC adapter is connected and is charging the battery.
Power and Power-Up Modes Battery types The computer has two types of batteries: ■ Battery pack ■ Real Time Clock (RTC) battery Battery pack When the AC adapter is not connected, the computer's main power source is a removable lithium ion battery pack, also referred to in this manual as the battery. You can purchase additional battery packs for extended use of the computer away from an AC power source. The battery is a disposable item.
Power and Power-Up Modes When this error appears, the following action is recommended. 1. Connect the AC adapter and let the battery charge for 24-hours. 2. Press F2 to enter BIOS setup menu. 3. Set correct time and date. If you still see the error message after performing the above actions, please contact your TOSHIBA service representative. Care and use of the battery pack The battery pack is a vital component of portable computing.
Power and Power-Up Modes 6. Use only the battery pack supplied with the computer or other device or an battery pack approved by the computer or device's manufacturer. Battery packs have different voltages and terminal polarities. Use of an improper battery could cause smoke, fire or rupture of the battery pack. 7. Never subject a battery pack to heat, such as storage near a heat source. Exposure to heat can cause the battery pack to ignite, explode or leak caustic liquid and cause death or serious injury.
Power and Power-Up Modes 5. Charge the battery pack only in an ambient temperature between 5 and 30 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. 6. Be sure to monitor the remaining battery power. If the battery pack or real time clock battery discharge completely, Sleep Mode will not function, and data in memory will be lost, and the computer might register an incorrect time and date.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes amber indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don't lose data) and automatically turns off. You must recharge a battery pack when it becomes discharged.
Power and Power-Up Modes Once a battery pack is fully charged, it is recommended that you operate the computer only on battery power until the battery pack completely discharges. Doing so extends battery life and helps ensure accurate monitoring of battery capacity. The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions: ■ The battery has not been used for a long time.
Power and Power-Up Modes Maximizing battery operating time A battery's usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer (for example, whether you enable battery power saving options). The computer provides a battery save mode to conserve battery power.
Power and Power-Up Modes Retaining data with power off (sleep mode) When you turn off your computer with fully charged batteries, the batteries retain data/charge for the following approximate time periods: Battery Approximately 2 days (Sleep mode, 12-cell) Approximately 1.
Power and Power-Up Modes 6. Unlock the Battery Pack Lock. 1 Removing the battery pack-1 7. Slide the battery pack latch to the left, then pull the battery out of the battery bay.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Turn the computer's power off. 2. Disconnect all cables connected to the computer. 3.
Power and Power-Up Modes TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows login password. User Password To start the utility, point to or click the following items: Launch TOSHIBA Assist SECURE User Password ■ Registered Click to register a password of up to 8 characters. After a password is set, you will be prompted to enter it when you start the computer.
Power and Power-Up Modes To enter a password manually, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message will appear in the LCD: Enter Password [xxxxxxxx] At this point, the hotkeys Fn + F1 to F9 do not work. They will function after you enter the password. 2. Enter the Password. 3. Press Enter. If you enter the password incorrectly three consecutive times, the computer shuts down. You must turn on the computer again and re-enter the password.
Power and Power-Up Modes 6-16 Satellite M100
Satellite M100 Chapter 7 HW Setup This chapter explains how to use the TOSHIBA HW Setup utility to configure your computer. TOSHIBA HW Setup lets you configure settings for various hardware devices through a number of tabs titled General, Password, Display, CPU, Boot Priority, Keyboard, LAN, and USB. Accessing HW Setup Start, point to All Programs, point to TOSHIBA, point to Utilities and click HWSetup.
HW Setup General This window displays the BIOS version and contains two buttons: Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. When finish BIOS update , please restart your computer and press F2 into BIOS setup manual and load BIOS default one time. Password This tab allows you to set or reset the user password for power on.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB floppy disk drive. N Selects the Network. C Selects optical device. To select the boot drive you want, follow the steps below. 1. Boot-up your computer and press F12 to enter the boot menu. 2.
HW Setup LAN Wake-up on LAN This feature lets the computer's power be turned on when it receives a wakeup signal from the LAN. Enabled Enables Wake-up on LAN. Disabled Disables Wake-up on LAN (Default). The Wake-up LAN function support AC adapter mode only, before you plan to use this function please make sure your AC power source is connected to system properly. Do not install or remove an optional memory module while Wake-up on LAN is enabled.
Satellite M100 Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility.
Optional Devices PC Card The computer is equipped with a PC Card expansion slot that can accommodate one 5 mm Type II card. Any PC Card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC Cards, including PC Card 16's multifunction card and CardBus PC Cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card 1. 2. 3. 4. 5. Click the Safely Remove Hardware icon on the Task Bar. Click the PC Card you want to remove. Press the eject button of the PC Card to extend it. Press the extended eject button to pop the card out slightly. Grasp the PC Card and remove it.
Optional Devices SD/MMC/MS/MS Pro/xD Memory cards The computer is equipped with a multiple digital media card slot that can accommodate SD/MMC/MS/MS Pro/xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, which use flash-memory.
Optional Devices Installing a memory card To install a memory card: 1. Insert the memory card. 2. Press gently to ensure a firm connection. Inserting a memory card Be sure the memory card is oriented properly before you insert it. If Windows fails to read the card, remove it then reinsert it. ■ The multiple digital media card slot only accepts one type of card at a time. Do not attempt to install more than one card as you risk damaging either the cards themselves or the computer.
Optional Devices Removing a memory card To remove a memory card, follow the steps below: 1. Click the Safely Remove Hardware icon on the Taskbar. 2. Select a device, then click the Stop button. A confirmation dialog may appear, depending on how the device is registered with the system; if so, confirm that you want to remove the device. 3. Gently press the memory card inside the socket to eject it. 4. Grasp the card and remove it.
Optional Devices Memory card care Set the write-protect switch to the lock position, if you do not want to record data. 1. Do not write to a memory card if the battery power is low. Low power could affect writing accuracy. 2. Do not remove a memory card while read/write is in progress. 3. The memory card is designed so that it can be inserted only one way. Do not try to force the card into the slot. 4. Do not leave a memory card partially inserted in the slot.
Optional Devices Installing Memory on Bottom Side If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. Follow these steps to install a memory module: 1. Set the computer to boot mode and turn off the power. Do not try to install a memory module under the following conditions. You can damage the computer and the module. 2. 3. 4. 5. a. The computer is turned on. b.
Optional Devices 2 1 Installing a module 8. Seat the cover and secure it with the screw. 9. Replace the battery pack as described in Chapter 6, Power and PowerUp Modes. 10. Turn the power on and make sure the added memory is recognized. Removing Memory on Bottom Side If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them.
Optional Devices 2 1 3 1 Removing the memory module 6. Seat the cover and secure its screw. 7. Replace the battery. Installing Memory Under Keyboard If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. Follow these steps to install main memory module: 1. Set the computer to boot mode and turn off the power. Do not try to install a memory module under the following conditions.
Optional Devices Pay attention not to give a damage on LCD panel when pushing up keyboard cover. 1 1 2 HOOK HOOK HOOK HOOK HOOK 150~170 Removing keyboard cover 1 Removing keyboard cover 6. Loosen the two screws securing the keyboard. 7. Push the Center of the keyboard, press the tab 8. Flip the keyboard out toward Touch Pad direction. Aware, keyboard cable still connected with system board.
Optional Devices 1 1 2 3 F8 3 M2XA F6 3 M2XA F8 F6 Removing keyboard 9. Loosen the two shield cover screws. 10. Remove the shield cover. 11. Fit the module's connectors into the computer's connectors at about a 45 degree angle and press the module carefully to ensure a firm connection. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 12. Push the module down so it lies flat.
Optional Devices 2 1 M2XA F8 F6 M2XA F8 F6 Installing memory module 2 2 F8 M2XA F6 1 M2XA F8 F6 Installing shild cover 14. Flip keyboard back and secure it with screws. 15. Replace the keyboard cover. Make sure all hooks are secured . 16. Replace the battery pack as described in Chapter 6, Power and Power Up Modes. 17. Turn the power on and make sure the added memory is recognized.
Optional Devices Removing Memory Under Keyboard If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. To remove the memory module, make sure the computer is in boot mode then: 1. Be sure the power is off and all cables are disconnected from the computer. Do not try to remove a memory module with the computer turned on. You can damage the computer and the module. 2.
Optional Devices Additional battery pack You can increase the portability of the computer with additional battery packs. If you're away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes. Additional AC adapter If you frequently carry the computer to different sites such as your home and office, having an AC adapter at each location reduces the weight and bulk of your load.
Optional Devices Television A television can be connected to the video out port on the computer. To connect a television, follow the steps below. 1. Turn the computer off. 2. Use a video cable (not supplied) to connect the television to the video out port. 3. Turn the television on. 4. Turn the computer on. You can use the hotkeys Fn + F5 or use the TV-Out button to change the display device. Refer to Chapter 5, The Keyboard.
Optional Devices 4. Click the Graphics Properties button. 5. In the subsequent dialogue box, click Display Devices and then set up your television and notebook displays.
Optional Devices For ATI 1. Click Start >Control Panel >Appearance and Personalization> Personalization. 2. Choose Display setting.
Optional Devices 3. Click the ATI Catalyst Control Center button. 4. Setup your television and notebook displays. i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as: ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Optical disc drives i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed. ■ Use S100, S200 or S400 cables no longer than three meters.
Satellite M100 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software The problems may be caused by your software. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting System start-up When the computer does not start properly, check the following items: ■ Self Test ■ Power Sources ■ Power-on Password Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: (This screen image is one of the examples. You may see the different screen image depending on the model you purchased.) This message remains on the screen for a few seconds.
Troubleshooting Power When the computer is not plugged into an AC outlet, the battery pack is the primary power source. However, your computer has a number of other power resources, including an intelligent power supply and Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems. This section provides check lists for AC power and the battery. If you cannot resolve a problem after following them, the cause could lie with another power resource.
Troubleshooting Battery If you suspect a problem with the battery, check the DC IN indicator as well as the indicators for the battery. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn't power the computer. The battery may be discharged. Connect the AC power cord to charge the battery. Battery doesn't charge when the AC power cord is attached. (Battery indicator does not glow amber.
Troubleshooting Problem Procedure Some letter keys produce numbers. Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled. Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software's documentation. If you are still unable to use the keyboard, consult your dealer. LCD panel Problem Procedure Lines appear broken. Check if you are in DOS mode.
Troubleshooting Password Problem Procedure Cannot enter password Refer to Chapter 6, Power and Power-Up Modes. i.LINK (IEEE1394) Problem Procedure i.LINK device does not Make sure the cable is securely connected to the function computer and to the device. Make sure the device's power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add New Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer.
Troubleshooting Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor's power switch is on. Confirm that the external monitor's power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display priority and make sure it is not set for the internal display.
Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. TouchPad Problem Procedure On-screen pointer does The system might be busy. If the pointer is shaped not respond to Pad as an hourglass, wait for it to resume its normal operation shape and try again to move it. You may also press Fn + F9 to enable the TouchPad and then try again to move it.
Troubleshooting Problem Procedure The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Options tab. 3. Set the speed as instructed and click OK. The mouse pointer moves erratically The mouse might be dirty. Refer to your mouse documentations for instructions on cleaning. If problems persist, contact your dealer. USB Refer also to your USB device’s documentation.
Troubleshooting LAN Problem Procedure Cannot access LAN or Check for a firm cable connection between the the Wake up on LAN LAN hub. feature does not work Make sure the AC adapter is connected. You cannot access a LAN using the computer's battery power. If problems persist, consult your LAN administrator.
Troubleshooting Modem Problem Procedure Communication Make sure the computer's internal modem software can't initialize settings are correct. Refer to Phone and Modem the modem Options Properties in the Control Panel. You can hear a dial tone If the call is going through a PBX machine, make but can't make a call sure the communication application's tone dial detection feature is disabled.
Troubleshooting CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a disc in the drive Make sure the drive's drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the disc is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the disc. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/ disconnect external devices or install/remove internal cards during writing.
Troubleshooting Problem Procedure The software or hardware configuration may be Some discs run correctly, but others do causing a problem. Make sure the hardware configuration matches your software's needs. not Check the disc's documentation. Check the type of disc you are using.
Troubleshooting Problem Procedure The software or hardware configuration may be Some discs run correctly, but others do causing a problem. Make sure the hardware configuration matches your software's needs. not Check the disc's documentation. Check the type of disc you are using.
Troubleshooting Real Time Clock Problem Procedure The following message is displayed on the LCD: RTC battery is low or CMOS checksum is inconsistent. Press [F2] key to set Date/ Time. The RTC battery charge has become exhausted, you should set the date and time in within the BIOS setup screen through the following steps: 1. Press [F1] key. BIOS setup will boot up. 2. Press [F2] to set the date in [System Date]. 3. Press [F2] to set the time in [System Time].
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia TOSHIBA (Australia) Pty, Ltd. Information Systems Division 84-92 Talavera Road, North Ryde, N.S.W. 2113 Sydney Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
Satellite M100 Chapter 10 Disclaimers This chapter states the Disclaimer(s) information applicable to TOSHIBA computers. CPU Central Processing Unit (“CPU”) Performance Disclaimer.
Disclaimers 64-Bit Computing. 64-bit processors are designed to take advantage of 32 and 64 bit computing. 64-bit computing requires that the following hardware and software requirements are met: ■ 64-bit Operating System ■ 64-bit CPU, Chipset and BIOS (Basic Input/Output System) ■ 64-bit Device drivers ■ 64-bit applications Certain device drivers and/or applications may not be compatible with a 64bit CPU and therefore may not function properly.
Disclaimers HDD Drive Capacity 1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content.
Disclaimers Copy Protection Copy protection technology included in certain media may prevent or limit recording or viewing of the media. Images All images are simulated for purposes of illustration. LCD Brightness and Eye Strain Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
Satellite M100 Appendix A Specifications This appendix summarizes the computer's technical specifications. Dimensions 343mm x 242mm x 38mm 36.5mm 242mm 343mm 29.8mm 38mm User’s Manual 29.8mm 36.
Specifications Weight Starting at 2.36kg/5.20lbs* * Weight may vary depending on product configuration, vendor components, manufacturing variability and options selected.
Specifications Built-in Modem Some computers in this series are equipped with Modem functionality. Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer's speaker Communication specifications Communication System Data: Fax: Communication Protocol Data: ITU-T-Rec (Former CCITT) Bell Fax: ITU-T-Rec (Former CCITT) Satellite M100 Full duplex Half duplex V.21/V.22/V.
Specifications A-4 Satellite M100
Satellite M100 Appendix B Display Modes This appendix contains a table listing all the display modes when the display is set to an external monitor. If you are running some applications (for example a 3D application or video playback and so on), you may see some disturbance, flickering or frame dropping on your screen. If that occurs, adjust the resolution of display, lowering it until the screen is displayed properly. You could also disable Windows Aero™. to help correct this situation.
Display Modes Some of display mode might not be supported depending on the external monitor which you use. Displaying movies on a TV or CRT This section describes how to set up your system to display movies simultaneously on your computer's LCD and on an external TV or CRT monitor. To connect a television, follow the steps below. 1. Turn the computer off. 2. Use a video cable (not supplied) to connect the television to the video out port. 3. Turn the television on. 4. Turn the computer on.
Display Modes 3. Click the Advanced Setting button. The (Multiple Monitors) and Mobile Intel® 945GM Express Chips dialogue box opens. 4. Click the Graphics Properties button.
Display Modes 5. In the subsequent dialogue box, click Display Devices and then set up your television and notebook displays. For ATI 1. Click Start >Control Panel >Appearance and Personalization> Personalization. 2. Choose Display setting.
Display Modes 3. Click the ATI Catalyst Control Center button. 4. Setup your television and notebook displays.
Display Modes B-6 Satellite M100
Satellite M100 Appendix C AC Power Cord and Connectors The power cord's AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region's power standards) Certification agencies U.S.
AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 215P (250V) or 1-15P (125V) and three pin plug coniguration must be 6-15P (250V) or 5-15P (125V) as designated in the U. S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U. S. A.
Satellite M100 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary SCSI: small computer system interface TFT: thin-film transistor USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array WXGA: wide extended graphics array A adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Glossary capacity: The amount of data that can be stored on a magnetic storage device such as a floppy disk or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB. CardBus: An industry standard bus for 32-bit PC cards. CD-ROM: A Compact Disc-Read Only Memory is a high capacity disc that can be read from but not written to. The CD-ROM drive uses a laser, rather than magnetic heads, to read data from the disc.
Glossary D DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions. Also called a preset value. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on.
Glossary G gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. graphics: Drawings, pictures, or other images, such as charts or graphs, to present information. H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk.
Glossary Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewingside coating is etched into character forming segments with leads that extend to the edge of the glass. Applying a voltage between the glass sheets alters the brightness of the liquid crystal. LSI: Large Scale Integration. 1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip.
Glossary P parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. peripheral device: An I/O device that is external to the central processor and/or main memory such as a printer or a mouse. pixel: A picture element.
Glossary T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. TouchPad: A pointing device integrated into the TOSHIBA computer palm rest. U Universal Serial Bus: This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.
