High-Resolution CMOS Camera Model CSB1100CL-10 PRODUCT SPECIFICATION Contents Before use – General safety instructions 1. Product Description·········································· 1 2. Features ····························································· 1 3. Configuration···················································· 1 4. Optional parts ··················································· 1 5. Specifications····················································· 2 6.
BEFORE USE - GENERAL SAFETY INSTRUCTIONS This instruction manual contains important information for the operator (user) and/or people in the vicinity to avoid personal injury, or property damage. • Prior to use, read this operation manual carefully to fully understand its instructions for correct use. • After reading, keep this manual near the equipment for future reference. WARNINGS & CAUTIONS [Definition of markings] The meaning of each mark used in this instruction manual is given below.
●Handling Precautions WARNING unplug Immediately cease use of the equipment in the event of abnormality or malfunction. If abnormal conditions are present, such as smoke, a burning smell, ingress of water or foreign matter, or if the equipment is dropped or malfunctions, fire or electric shock may result. If such abnormalities occur, disconnect the power plug from the outlet and contact your sales representative. Do not use the equipment in locations subject to water splashes.
CAUTION Observe the following when installing the equipment: · Do not cover the equipment with a cloth, etc. · Do not place the equipment in a narrow location where heat is likely to accumulate. Otherwise, heat will accumulate inside the equipment, possibly resulting in a fire. Instruction Do not place the equipment in locations subject to high moisture, oil fumes, steam, or dust. Otherwise, fire or electric shock may result.
CASES FOR INDEMNITY (LIMITED WARRANTY) We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the user in the following cases. In the case damage or losses are caused by fire, earthquake, or other acts of God, acts by a third party, deliberate or accidental misuse by the user, or use under extreme operating conditions.
Usage Precautions Handle carefully Do not drop the equipment or allow it to be subject to strong impact or vibration, as such action may cause malfunctions. Further, do not damage the connection cable, since this may cause wire breakage. Environmental operating conditions Do not use the product in locations where the ambient temperature or humidity exceeds the specifications. Otherwise, image quality may be degraded or internal components may be adversely affected.
1. Product Description Model CSB1100CL-10 is a high-resolution B/W CMOS camera achieving high-speed image processing by a random access. 2. Features (1) Ultra-high resolution The CSB1100CL-10 features a high-pixel CMOS sensor (Total pixel count: 1.31 Mega pixels), enabling high-density images (i.e., significantly reduced moiré and beat) to be obtained. (2) Global shutter mode This model features a Global shutter mode, which means that clear images of a fast-moving subject with little blurring are obtained.
5. Specification Model Image sensor Total pixel Active pixel Pixel size Image area Driving frequency Scanning line Scanning system Flame rate Sync system Aspect ratio Subject illumination Video output S/N Control signal Gamma Electronic shutter Shutter mode Random Trigger Shutter CSB1100CL-10 CMOS Image sensor 1280 (H) x 1024 (V) 1240 (H) x 1023 (V) 6.7 (H) x 6.7 (V) micro m 8.308 x 6.854 mm 33.3333MHz 1023 lines Progressive 22.
6. Connection (1) DC IN Connector (Camera side): HR10A-7R-6PB Plug (Cable side): HR10A-7P-6S Pin number 1 2 3 4 5 6 Signal name N.C. N.C. GND N.C. N.C. +12V (Manufactured by HIROSE DENKI) (Manufactured by HIROSE DENKI) 1 6 2 5 3 4 Rear-view (2) DATA IN/OUT Connector (Camera side): 10226-2210VE Connector (Cable side): 10126-6000 PIN. Signal Name I/O PIN.
7. DIP switch setting The setting of each mode can be done with DIP switches located on the rear panel.
8. Function (1) Electronic shutter The shutter-speed of CSB1100CL-10 is also manually adjustable. By manipulating the internal register setting value of CSB1100CL-10, you can change the shutter-speed by user-defined setting value of 65.8 micro sec step. * The longer a user sets the exposure time, the more defective pixels on the image is outstanding. When you attach importance to image quality, it is recommendable to set the shutter speed at 30 msec or less.
The placement is available up to 16 windows in all active pixel area. 1 2 3 5 9 4 6 8 11 12 15 7 14 16 10 13 The setting of readout address is available up to 8 types. 1 2 34 56 78 User can reprogram all setting types from 1 through 8.
Practical operation example In the case of only one readout area A readout area can be designated by the start address (X1, Y1) and the end address (X2, Y2). The camera can read out the user-defined area through this function. The each address is designated by the start address and lengths (pixel numbers) of “X” and “Y” directions.
9. Timing Chart (1) Normal shutter mode (in all pixel data readout) Depends on register setting Integrate time EXPOSURE (CAMERA INTERNAL) Approx. 15.66us FRAME (CAMERA INTERNAL) Approx. 13.38us VIDEO DATA image A (CAMERA OUTPUT) 43.7ms image B 43.73ms + Exposure time (2) Random Trigger Shutter mode (Fix mode) Trigger disable time Trigger disable time TRIG (EXTERNAL) Integrate time Depends on register setting Approx . 28us no reaction EXPOSURE (CAMERA INTERNAL) Approx. 15.
(3) Random trigger shutter (pulse mode) Shutter speed depends on the trigger pulse width. After trigger IN, next trigger signal is acceptable until the readout is completed. Trigger disable time Trigger disable time TRIG (EXTERNAL) Integrate time Approx. 300ns Approx . 28us no reaction EXPOSURE (CAMERA INTERNAL) Approx. 15.66us FRAME (CAMERA INTERNAL) Approx. 13.38us VIDEO DATA image A (CAMERA OUTPUT) image B 43.7ms 43.
11.