E7J70BD_EN.
E7J70BD_EN.book Page 2 Monday, May 7, 2007 3:31 PM Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet.
E7J70BD_EN.book Page 3 Monday, May 7, 2007 3:31 PM Connection to Power BLUE (Neutral) BROWN (Live) CORD GRIP OUTER SHEATH OF THE WIRE Installation Location For safety and optimum performance of this unit: • Install the unit in a horizontal and stable position. • Do not place anything directly on top of the unit. • Do not place the unit directly on top of the TV. • Shield the unit from direct sunlight and keep away from sources of intense heat. Avoid dusty or humid locations.
E7J70BD_EN.book Page 4 Monday, May 7, 2007 3:31 PM About Copyright Declaration of Conformity Unauthorised copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorised by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision.
E7J70BD_EN.book Page 5 Monday, May 7, 2007 3:31 PM Introduction Accessories Supplied • Remote control with two R6 (AA) batteries OPEN/ CLOSE .@/ : INPUT SELECT HDMI ABC DEF MNO PROG. PQRS TUV WXYZ TIMER PROG. SETUP SPACE CLEAR GHI JKL INFO DISC MENU TEXT TOP MENU GUIDE ENTER /OK RETURN /BACK DISPLAY PLAY REV SKIP FWD SKIP Connections PAUSE STOP 1.3x/0.8x PLAY INSTANT SKIP TIME SLIP REC REC MODE ZOOM REPEAT AUDIO SAT.
E7J70BD_EN.book Page 6 Monday, May 7, 2007 3:31 PM Table of Contents Introduction ............................................ 2 Playback ................................................47 Precautions ........................................................... 2 Basic Playback .................................................... 47 Features ................................................................ 7 PBC Function for Video CDs ............................... 52 Guide to the Owner’s Manual......
E7J70BD_EN.book Page 7 Monday, May 7, 2007 3:31 PM This unit not only plays back DVDs and CDs but also offers features for you to record on DVD discs and edit them after that. The following features are offered with this unit. The unit is compatible with DVD-RW, DVD+RW discs, which are recordable repeatedly, and DVD-R, DVD+R discs, which are recordable only once. Recording up to 12 programmes: You can programme the unit to record up to 12 programmes, up to a month in advance.
E7J70BD_EN.book Page 8 Monday, May 7, 2007 3:31 PM Compatibility Playing back discs recorded in Video mode on any regular DVD player: Discs recorded in Video mode can be played back on regular DVD players, including computer DVD drives compatible with DVD-Video playback. You will need to finalise the discs recorded in Video mode to play back in other DVD players.
E7J70BD_EN.book Page 9 Monday, May 7, 2007 3:31 PM Introduction Discs for Recording, Playing DVD-RW Disc Type DVD-R DVD+RW DVD+R Logo Format Video Mode Icon Automatically formatted in +VR mode Automatically formatted in +VR mode VR Mode Video VR DVD-RW DVD-RW DVD+R DVD+R Ver. 1.1,1.2 Ver. 1.1/2× CPRM compatible Ver. 1.2/4× CPRM compatible Ver. 2.0 Ver. 2.0/4× Ver. 2.0/8× Ver. 2.0/16× 1×-4× 1×-16× Playable on most DVD players. Finalisation necessary.
E7J70BD_EN.book Page 10 Monday, May 7, 2007 3:31 PM Discs for Playing Disc Type DVD-VIDEO CD-DA Video CD CD-RW CD-R Logo Icon DVD-V CD VCD CD CD Files for Playing Type of title Icon Media MP3 MP3 CD-RW/-R JPEG DivX® JPEG CD-RW/-R DivX ® CD-RW/-R DVD-RW/-R DVD+RW/+R is a trademark of DVD Format/Logo Licensing Corporation. DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license. • Official DivX® Certified product; Plays DivX® 6.
E7J70BD_EN.book Page 11 Monday, May 7, 2007 3:31 PM Introduction Functional Overview Front Panel 1 2 3* 4 5 7 6 8 OPEN/CLOSE SKIP STOP PLAY 1080i 1 11 ON/STANDBY button Disc tray 7 Infrared sensor window • Receive signals from your remote control so that you can control the unit from a distance. H (SKIP) button 8 6 G (SKIP) button • Lights up and indicates the HDMI output mode when HDMI output is on. 9 AUDIO input jacks (AV3) • Use to connect external device with a RCA audio cable.
E7J70BD_EN.book Page 12 Monday, May 7, 2007 3:31 PM Rear Panel COAXIAL IN Y DIGITAL AUDIO OUTPUT PCM/BITSTREAM L HDMI OUT PB/CB R OUT DVB-T PR/CR ANALOG ANTENNA COMPONENT ANALOG VIDEO OUTPUT AUDIO OUT 1 23 4 5 1 AV2 (DECODER) 67 8 AV1 (TV) 9 10 ANTENNA IN (DVB-T) 11 6 • Connect to an antenna or cable to receive DVB-T signal. 2 ANTENNA OUT (DVB-T) • Connect to the audio input jacks on your TV. Use a commercially available Audio cable.
E7J70BD_EN.book Page 13 Monday, May 7, 2007 3:31 PM Introduction Remote Control 7 1* 2 OPEN/ CLOSE INPUT SELECT HDMI .@/ : ABC DEF JKL MNO PQRS TUV WXYZ TIMER PROG. CLEAR INFO DISC MENU TEXT TOP MENU GUIDE 9 21 RED/GREEN/YELLOW/BLUE button • Press to follow the DVB instruction displayed on-screen. 20 10 REV r button • During playback, press to fast reverse. • When playback is paused, press to reverse slowly.
E7J70BD_EN.book Page 14 Monday, May 7, 2007 3:31 PM 23 TEXT button • Press to switch Teletext on or off, or transparent mode. 24 GUIDE button • Press to call up the EPG list in DVB mode. 25 ENTER/OK button • Press to acknowledge or approve a menu selection. Installing Batteries in the Remote Control Install two R6 (AA) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment.
E7J70BD_EN.book Page 15 Monday, May 7, 2007 3:31 PM Guide to On-Screen Displays File Name 1 My File DISPLAY Menu 5 6 1/ 5 1/ 5 (only when a CD with MP3/JPEG/DivX® files is in playback) 1 0:01:00 / 1:23:45 1 -RW 3 VR Displays title/file name. Connections With a disc inserted into the unit, press [DISPLAY] to display the On-Screen Display. The menu shows information about what is recorded on the disc. Introduction ORG 2 Video Info. : Audio Info.
E7J70BD_EN.book Page 16 Monday, May 7, 2007 3:31 PM 7 Main Menu Press [SETUP] to display the main menu. Then use [K / L] to select a menu and press [ENTER/OK] to display the sub menu. These menus provide entries to all main functions of the unit. Setup 1 2 3 4 5 6 1 DivX: To set up the setting for the DivX® playback. 8 HDMI: To set up the HDMI connection setting. 9 Reset All: To reset the setting to the factory default.
E7J70BD_EN.book Page 17 Monday, May 7, 2007 3:31 PM Disc Protect (VR mode DVD-RW, DVD+RW/+R disc only): Introduction 3 Allows you to protect a disc from accidental editing or recording. 4 Delete All Playlists (VR mode DVD-RW disc only): Allows you to delete Playlist. Connections 5 Random Play: Allows you to activate the random playback feature. 6 Program Play (audio CD/video CD only): Allows you to activate the programme playback feature.
E7J70BD_EN.book Page 18 Monday, May 7, 2007 3:31 PM Front Panel Display Guide 2 1 3 1 Current status of the unit 2 Title / Track and Chapter number p: Appears when disc playback is paused. Appears also during step by step playback. B: Appears when playing back a disc. : Appears during slow forward playback. : Appears when the timer programming or One-touch Timer Recording (OTR) is set and is operating. Appears when the unit goes into the Satellite Link standby mode.
E7J70BD_EN.book Page 19 Monday, May 7, 2007 3:31 PM Introduction Connections Connections Connect the unit to a TV after considering the capabilities of your existing equipment. Before installation, plug off your TV and this unit. Using the Scart socket Make a connection for the TV signal. Depending on the TV signal’s situation, choose one of following methods (A-C).
E7J70BD_EN.book Page 20 Monday, May 7, 2007 3:31 PM Selecting Progressive Scan (576p/480p or Interlaced 576i/480i) Playback • If your TV is compatible with progressive scanning (576p/480p), connect the TV to the COMPONENT VIDEO OUTPUT jacks of this unit and set “Video Out” setting to “Component Progressive (P)” in the setup menu. (See page 74.) Next, set your TV to the progressive scan mode. • If your TV is not compatible with progressive scan, set “Video Out” setting to “Component Interlace (I)”.
E7J70BD_EN.book Page 21 Monday, May 7, 2007 3:31 PM Introduction Note Connecting to External Equipment This unit has three input terminals, AV1 or AV2 on the rear panel and AV3 on the front panel. Be sure that all the units are off before making connections.
E7J70BD_EN.book Page 22 Monday, May 7, 2007 3:31 PM Digital Audio for Better Sound Quality Dolby Digital decoder, DTS decoder or MPEG decoder, etc. Digital audio input jacks COAXIAL After You Have Completed Connections Switch the input selector on your TV to an appropriate external input channel. For details, refer to the Owner’s Manual of your TV.
E7J70BD_EN.book Page 23 Monday, May 7, 2007 3:31 PM Introduction Basic Setup Channel Setting Turn on this unit for the first time, you need to follow these steps. Tuning of this unit to broadcast channels can be performed in two ways. 1 2 Press [ Auto Tuning (DVB & ANALOG) 3 Select your desired channel preset type using [U / D]. Then press [ENTER/OK]. ON / STANDBY]. Turn the TV on. Select the input to which the unit is connected.
E7J70BD_EN.book Page 24 Monday, May 7, 2007 3:31 PM Auto Tuning (ANALOG) Manual Tuning (ANALOG) ANALOG ANALOG Programme the tuner to scan only the channels you can receive in your area. 1 In stop mode, press [SETUP]. Select “General Setting” using [U / D], then press [ENTER/OK]. General Setting Menu will appear. 2 Select “Channel” using [U / D], then press [ENTER/OK]. 3 Select “ANALOG Channel Setup” using [U / D], then press [ENTER/OK]. 4 Select “Auto Tuning” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 25 Monday, May 7, 2007 3:31 PM After completion, press [SETUP] to exit. To Skip a Preset Channel ANALOG Move the channel to another position number using [U / D], then press [ENTER/OK]. • To move another channel, repeat steps 4 to 6. 7 Press [SETUP] to exit. Auto Tuning (DVB) DVB You can programme the tuner to scan only the DVB channels that you can receive in your area. 1 In stop mode, press [SETUP]. Select “General Setting” using [U / D], then press [ENTER/OK].
23_31_BasicSetup_EN.fm Page 26 Tuesday, July 17, 2007 1:14 PM Manual Tuning (DVB) DVB You can preset a DVB channel manually and individually. To switch DVB, analogue and external input (AV1/ AV2/AV3) mode. You can switch between DVB, analogue and external input (AV1/AV2/AV3) mode by pressing [INPUT SELECT ] repeatedly. The mode changes as follows: DVB mode 1 Follow steps 1 to 3 in “Auto Tuning (DVB)” on page 25. 2 Select “Manual Tuning” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 27 Monday, May 7, 2007 3:31 PM DVB You can create 4 different favourite lists (TV1 - TV4) with your preferred DVB channels and radio stations. By setting the certain favourite list, you can loop channels only within the list when you use [PROG. / ]. 2 3 Press [SETUP] or [RETURN/BACK] to exit. Note • This function is available for only favourite lists (TV1-TV4). Adult Lock DVB You can select DVB channels and radio stations to prevent access to it.
23_31_BasicSetup_EN.fm Page 28 Friday, July 13, 2007 5:24 PM 4 TV View Operation Select the desired option using [U / D], then press [ENTER/OK]. General Setting The following operations are available while viewing TV channels through this unit’s tuner. Playback Display Video Recording Clock Channel DivX HDMI Reset All Selecting the Audio Mode You can switch between TV audio modes by pressing [AUDIO ] on the remote control. Each mode is indicated on the TV screen.
E7J70BD_EN.book Page 29 Monday, May 7, 2007 3:31 PM DVB 1 2 In stop mode, press [SETUP]. Select “Timer Programming” using [U / D], then press [ENTER/OK]. • Select the TV programme using [U / D], then press the [ENTER/OK] to watch the selected channel or press [BLUE] to display time schedule of the DVB channel. • From the EPG screen, you can also set the timer recording. Refer to “Timer Recording (EPG)” on page 42. You can make settings of the digital tuner from the DVB Menu.
23_31_BasicSetup_EN.fm Page 30 Tuesday, July 17, 2007 1:13 PM Language Setting About DVB DVB 1 Follow steps 1 to 2 in “PINCODE Setting for Adult Lock” on page 29. You can check the current DVB system software version of this unit. 2 Select “Language” using [U / D], then press [ENTER/OK]. 1 Follow steps 1 to 2 in “PINCODE Setting for Adult Lock” on page 29. 3 Select the item you want to change the language using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 31 Monday, May 7, 2007 3:31 PM Manual Clock Setting In stop mode, press [SETUP]. Select “General Setting” using [U / D], then press [ENTER/OK]. This unit receives time signals from the analogue / DVB channels, and set the clock automatically. Set the channel tuning before setting Auto Clock. 2 Select “Clock” using [U / D], then press [ENTER/OK]. 1 In stop mode, press [SETUP]. Select “General Setting” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 32 Monday, May 7, 2007 3:31 PM Recording Information on DVD Recording Type of Discs This unit can record on DVD-RW/-R discs and DVD+RW/+R discs. DVD-R/+R discs allow you to record programmes only once, and the recorded contents can be erased although the space left on the disc does not change. DVD-RW/+RW discs allow you to record programmes repeatedly, and the recorded contents can be erased. There are 3 recording formats: VR mode, Video mode and +VR mode.
E7J70BD_EN.book Page 33 Monday, May 7, 2007 3:31 PM Formatting a Disc Choosing the Recording Format of a Blank DVD-RW Disc After recording, you must finalise the disc to play it back in other players. (See page 45.) You cannot finalise discs in other DVD recorders. In stop mode, press [SETUP]. Select “DVD Menu” using [U / D], then press [ENTER/OK]. “DVD Menu” menu will appear. 3 Select “Format” using [U / D], then press [ENTER/OK]. Format menu will appear.
E7J70BD_EN.book Page 34 Monday, May 7, 2007 3:31 PM Make Recording Compatible 4 Select your desired setting using [U / D], then press [ENTER/OK]. DVD+RW DVD+R DVD+R Use this feature to make the unfinalised +VR mode discs recorded on other unit recordable on this unit. When you make an additional recording on this unit with “Make Recording Compatible” set to “ON”, the title list is automatically converted to this unit’s style. 1 In stop mode, press [SETUP].
E7J70BD_EN.book Page 35 Monday, May 7, 2007 3:31 PM If you wish to set “Auto Chapter” off, select “OFF” using [U / D], then press [ENTER/OK]. 5 Select “Yes” using [U / D], then press [ENTER/OK]. e.g.
E7J70BD_EN.book Page 36 Monday, May 7, 2007 3:31 PM Selecting the Sound Mode This unit can receive bilingual broadcasts. You can switch between modes by pressing [AUDIO ] on the remote control. Each mode is indicated on the TV. When you record a DVB channel, only output sound channel will be recorded. Setting Bilingual Recording Audio Video DVD-RW DVD-R DVD+R DVD+RW VD+RW W DVD+R DVD+R You can select either “Main” or “Sub” audio to record a bilingual broadcast in Video mode or +VR mode.
E7J70BD_EN.book Page 37 Monday, May 7, 2007 3:31 PM Select “PCM” or “Dolby Digital” using [U / D], then press [ENTER/OK]. Basic Recording General Setting Auto Chapter Audio Select (XP) Recording Recording Audio Select (XP) Auto Finalise PCM Aspect Ratio (Video mode) Dolby Digital Make Recording Compatible Bilingual Recording Audio External Input Audio 5 DVD-R DVD+R DVD+RW VD+RW W 1 Press [ the unit.
E7J70BD_EN.book Page 38 Monday, May 7, 2007 3:31 PM One-Touch Timer Recording (OTR) Video VR DVD-RW DVD-RW DVD-R DVD+R DVD+RW VD+RW W DVD+R DVD+R This is a simple way to set the recording time in blocks of 30 minutes. Check that the disc you are recording onto has enough space remaining for the time you set. 1 2 3 4 Turn on the unit and insert a recordable disc. Make sure that the TV input is set on the unit. Select the recording mode using [REC MODE]. (See page 32.
E7J70BD_EN.book Page 39 Monday, May 7, 2007 3:31 PM Timer Recording Video VR DVD-RW DVD-RW To record from the external input, select “AV1”, “AV2”, or “AV3”. DVD-R DVD+R DVD+RW VD+RW W 6 Refer to “Recording Mode” on page 32. 7 Insert a recordable disc. In stop mode, press [TIMER PROG.]. Refer to “PDC (Programme Delivery Control)” on page 40. • When DVB channel is selected, “STTL” will be displayed instead of “PDC”.
E7J70BD_EN.book Page 40 Monday, May 7, 2007 3:31 PM PDC (Programme Delivery Control) Programme Delivery Control (PDC) assures that the TV programmes you have programmed for timer recording are recorded exactly from beginning to end, even if the actual broadcasting time differs from the scheduled time due to a delayed start or extension of the programme duration. Furthermore, if a programme is interrupted, the recording will also be interrupted automatically and resumed when the programme starts again.
E7J70BD_EN.book Page 41 Monday, May 7, 2007 3:31 PM Actual recording PROG. 1 If the recording time entirely overlaps: • The shorter timer programming (PROG. 1) is not recorded. PROG. 1 PROG. 2 Actual recording PROG. 2 Note for DVD recording • If the recording time of two programmes are overlapped, or the End time of a programme and the Start time of another is same, the first 2 minutes (at the longest) of the subsequent programme will be cut off.
E7J70BD_EN.book Page 42 Monday, May 7, 2007 3:31 PM Timer Recording (EPG) Satellite Link With EPG system, you can programme DVB channel recording much easier. You only choose a programme and enter the selection. You can set the unit to start recording whenever it detects the video scart control from the external tuner. 1 Preparing for the Satellite Link Timer Recording: While viewing DVB channel, press [GUIDE].
E7J70BD_EN.book Page 43 Monday, May 7, 2007 3:31 PM Press [ENTER/OK]. Introduction 5 Example 1 “To Standby Mode” is highlighted. Timer Recording Satellite Link Satellite Link Start Mode Actual Recording Connections 3:00 XP To Standby Mode Example 2 Timer Recording 6 Satellite Link In a second, the unit will be turned off automatically as it goes into the Satellite Link standby mode. • Until the time you set in “Start”, the clock will appear on the front panel display.
E7J70BD_EN.book Page 44 Monday, May 7, 2007 3:31 PM 2 Press [OPEN / CLOSE O] to open the disc tray, then place the disc to record on. Press [OPEN / CLOSE O] again to close the disc tray. 3 Select the input terminal to which the external equipment is connected. (AV1, AV2, or AV3) Settings for External Equipment Connection to External Equipment Video VR DVD-RW DVD-RW DVD-R DVD+R DVD+RW VD+RW W DVD+R DVD+R Connect the external equipment using either the input jacks, AV1, AV2 (Rear) or AV3 (Front).
E7J70BD_EN.book Page 45 Monday, May 7, 2007 3:31 PM Finalising Discs VR DVD-RW DVD+RW DVD+R DVD+R To prevent accidental over-recording, editing or erasing of recordings, you can protect them using the Setup menu. 3 Select “DVD Menu” using [U / D], then press [ENTER/OK]. Select “Disc Protect OFF using [U / D], then press [ENTER/OK]. ON” Select “Yes” using [U / D], then press [ENTER/OK]. The disc is protected. 5 Press [SETUP] to exit.
E7J70BD_EN.book Page 46 Monday, May 7, 2007 3:31 PM 5 Finalising is complete. Hint • Finalising a disc in Video mode and +VR mode automatically creates a Title menu. • After you finalise the DVD+RW disc, you can call up the title list by pressing [TOP MENU], or you can call up the Title menu by pressing [DISC MENU]. • Even after DVD+RW disc is finalised, you can still record or edit. After you finalise DVD-RW/-R or DVD+R disc, you cannot edit or record anything else on that disc.
E7J70BD_EN.book Page 47 Monday, May 7, 2007 3:31 PM Introduction Playback 6 Pop up window will appear. Hint for DVD Playback The contents of a DVD are generally divided into titles. Titles are sometimes further subdivided into chapters. Start Rec. Stop/Start Stop Rec. 7 Select “Play From Start” using [U / D], then press [ENTER/OK]. Playback will start. 8 Press [STOP S] to stop playback. To eject the disc, press [OPEN / CLOSE O] to open the disc tray, then remove the disc.
E7J70BD_EN.book Page 48 Monday, May 7, 2007 3:31 PM Playing Back an Audio CD, MP3 or JPEG CD 1 MP3 JPEG Follow steps 1 to 4 in “Playing Back a DVD-RW / DVD-R / DVD+RW / DVD+R Disc” on page 47. The File List will appear. JPEG file1 JPEG file2 MP3 file1 MP3 file2 MP3 file3 MP3 file4 1/ 2 To exit the File List, press [TOP MENU] again or press [STOP S]. To resume the File List, press [TOP MENU]. Press [U / D] to select the desired folder or track / file, then press [ENTER/OK].
E7J70BD_EN.book Page 49 Monday, May 7, 2007 3:31 PM The subtitle created by the user can be displayed during DivX® playback. 1 After the DivX® file is selected, the Subtitle List will appear. Subtitle List OFF SMI SRT SUB ASS SSA TXT Use [L / P] to select “Yes” if you want to play back the file, or to select “No” if you do not wish to play it back. Then press [ENTER/OK] to confirm the selection. Select the desired extension you want to display using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 50 Monday, May 7, 2007 3:31 PM • Up to 8 hierarchies can be recognised in one folder. Files in the 9th or deeper hierarchies cannot be played back. • If the track extends beyond the scope of screen, a down arrow “ ” appears, indicating that the user can view another part on the previous page. The current page number and the number of total pages are shown on the right of the down arrow “ ”. • Letters of a file / folder name overflowing the given space will be displayed as “…”.
E7J70BD_EN.book Page 51 Monday, May 7, 2007 3:31 PM DVD-V A DVD contains a disc menu, which lists the contents and enables you to customise playback. The menu may offer choices for subtitle languages, special features, and chapter selection. Usually this information appears automatically when you start playback, but sometimes you need to press [DISC MENU] to display the menu. DVD-V Some DVDs have a Title menu, which lists the titles available on the DVD.
E7J70BD_EN.book Page 52 Monday, May 7, 2007 3:31 PM PBC Function for Video CDs VCD This unit conforms to ver.1.1 and ver.2.0 of the Video CD standard playback control (PBC) function. This enables you to play back interactive software using menu screens. Refer to the information accompanying the Video CD. Ver.1.1 (without PBC function): You can still enjoy playback of pictures and music from the CD. Ver.2.
E7J70BD_EN.book Page 53 Monday, May 7, 2007 3:31 PM Special Playback Resume Playback DVD-V Video VR DVD-RW DVD-RW DVD+R DVD+R CD DVD-R VCD MP3 (PBC OFF) JPEG DivX ® You can resume playback from the point where you stopped it before. 1 Skipping TV Commercials during Playback During playback, press [STOP S]. The resume message will appear. DVD-V Press [PLAY P]. DVD+R DVD+RW VD+RW W In a few seconds, playback will resume from the point at which you stopped it before.
E7J70BD_EN.book Page 54 Monday, May 7, 2007 3:31 PM 1 During playback, press [1.3x/0.8x PLAY]. Px0.8 : Press [1.3x/0.8x PLAY] once during playback. Plays back approximately at 0.8 times of normal playback. Px1.3 : Press [1.3x/0.8x PLAY] twice during playback. Plays back approximately at 1.3 times of normal playback. P : Press [1.3x/0.8x PLAY] thrice to play back in normal speed. No effects.
E7J70BD_EN.book Page 55 Monday, May 7, 2007 3:31 PM Select the desired zoom position using [U / D / L / P], then press [ENTER/OK]. Zoom playback will start. Hint Note • If selecting a smaller factor than that currently selected, the zoom area is not displayed. • You cannot slide the zoomed picture on some JPEG files.
E7J70BD_EN.book Page 56 Monday, May 7, 2007 3:31 PM 2 Using the [TIME SLIP] button With [TIME SLIP] button, even if you leave your couch while you are watching TV through this unit, you can come back and watch rest of the programme from right where you left at any convenient time with just one button. Please make sure to put VR mode DVD-RW disc, and set the recording mode to LP, EP or SLP. 1 The title number next to While viewing a TV broadcast via this unit, press [TIME SLIP]. Press [TIME SLIP] again.
E7J70BD_EN.book Page 57 Monday, May 7, 2007 3:31 PM CD Video VR DVD-RW DVD-RW DVD-R JPEG DivX ® Using [SKIP B / F] buttons 1 DVD+R DVD+R Using [SKIP B / F] buttons 1 MP3 The unit moves to the next track one after the other. To go back to the previous track, press [SKIP B] twice in quick successions. The unit moves backward one track at a time. During playback, press [SKIP F] to skip the current title or chapter and move to the next.
E7J70BD_EN.book Page 58 Monday, May 7, 2007 3:31 PM Time Search DVD-V DVD+R DVD+RW VD+RW W Video VR DVD-RW DVD-RW DVD+R DVD+R CD Repeat / Random / Programme Playback / Slide Show DVD-R VCD DivX ® (PBC OFF) Repeat Playback For audio CD, skip to step 2. 1 2 During playback, press [DISPLAY]. DVD-V Select the icon using [L / P], then press [ENTER/OK]. DVD+R DVD+RW VD+RW W for the title or track number is highlighted. 3 4 Press [L / P] to highlight .
E7J70BD_EN.book Page 59 Monday, May 7, 2007 3:31 PM • You can only set A-B repeat playback within the current title (for DVDs) or current track (for Audio CDs, Video CDs and discs with DivX® files). • You cannot select “Group” during the random playback of MP3 and JPEG files. • Chapter / Track repeat function is cancelled whenever [SKIP B / F] is pressed. • For some DivX® files, A-B Repeat playback may not function. • For Video CDs with PBC function, repeat play does not work while the PBC function is on.
E7J70BD_EN.book Page 60 Monday, May 7, 2007 3:31 PM 3 Selecting the Format of Audio and Video With a DVD Video, VR mode DVD-RW, or DivX® files: Audio soundtrack will switch. Example: English → Spanish → French You can select the format of audio and video to suit the content of the disc you are playing back. Switching Subtitles If the title contains both main and sub audio, you can further select L (main), R (sub), L/R (mixed of main and sub).
E7J70BD_EN.book Page 61 Monday, May 7, 2007 3:31 PM Introduction Switching Camera Angles DVD-V Some DVD-Videos feature scenes shot from two or more angles. The disc case is usually marked with an angle icon if the disc has multi-angle scenes. During playback, press [DISPLAY]. Connections 1 The angle icon appears when a switching camera angle is available. (Available only when the angle icon appears in bottom right on the TV screen.) 2 Select the icon using [L / P], then press [ENTER/OK].
E7J70BD_EN.book Page 62 Monday, May 7, 2007 3:31 PM Editing 8 Disc Editing You can edit a disc recorded using the PAL system. It is not possible to edit discs recorded using the NTSC system. Guide to a Title List Title list allows you to check the titles recorded on the disc easily. You can choose a title to play back from this list and easily edit the titles as you prefer. Press [TOP MENU].
E7J70BD_EN.book Page 63 Monday, May 7, 2007 3:31 PM Video VR DVD-RW DVD-RW DVD-R DVD+R DVD+RW VD+RW W ORG 4 “Are you sure?” will appear. Select “Yes” using [U / D], and then press [ENTER/OK]. Title is deleted. 5 Note • If you delete the title in DVD+RW disc, deleted title will be displayed as “Empty”. • You cannot overwrite on the “Empty”.
E7J70BD_EN.book Page 64 Monday, May 7, 2007 3:31 PM 5 To enter the title name, refer to “Guide to Editing Title Names” on this page. ORG Edit A B a b 1 2 @ ! VR DVD-RW DVD+RW 0:00:59 When you finish entering the title name, press [ENTER/OK]. Select “Yes” using [U / D], then press [ENTER/OK]. 1 Follow the steps 1 to 3 in “Editing Title Name” on page 63. 2 Select “Chapter Mark” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 65 Monday, May 7, 2007 3:31 PM 5 Press [RETURN/BACK]. Press [RETURN/BACK] again and then [RETURN/BACK] or [STOP S] to exit. Writing on the disc starts. It may take awhile to write the data on a disc. Video 1 Follow the steps 1 to 3 in “Editing Title Name” on page 63. 2 Select “Chapter Mark” using [U / D], then press [ENTER/OK]. DVD+RW DVD+R DVD+R You can hide chapters from the title list. Hidden chapters are skipped during playback.
E7J70BD_EN.book Page 66 Monday, May 7, 2007 3:31 PM 3 Protecting Titles Select “Title Dividing” using [U / D], then press [ENTER/OK]. Select “Yes” using [U / D], then press [ENTER/OK]. 4 VR DVD-RW Original e.g.) VR mode DVD-RW disc playlist To prevent the accidental editing or erasing of the titles, you can protect them in the Original menu. 1 2 PL Follow the steps 1 to 3 in “Editing Title Name” on page 63. Select “Protect” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 67 Monday, May 7, 2007 3:31 PM Deleting All Playlists VR VR DVD-RW Original 1 Follow the steps 1 to 2 in “Deleting Titles” on page 63. 2 Select “Add To Playlist” using [U / D], then press [ENTER/OK]. 1 2 Press [SETUP]. 3 Select “Delete All Playlists” using [U / D], then press [ENTER/OK]. Select “DVD Menu” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 68 Monday, May 7, 2007 3:31 PM 4 Deleting Parts of Titles Select “Delete” using [U / D], then press [ENTER/OK]. VR DVD-RW You can delete a specific part of a title. Even when a title is deleted from the Playlist, the original title will remain as it is. The available recording time on the disc will not increase. 1 2 PL 1 e.g.
_77_Function Setup_EN.fm Page 69 Friday, July 13, 2007 5:33 PM Introduction Function Setup The following table is the contents which you can set and the default settings. Refer to the following table for useful operation. Playback Items (highlight is the default) ON OFF Compressing the range of sound volume. PCM 48kHz 96kHz Set whether the sound recorded in 96kHz will be down sampled in 48kHz.
E7J70BD_EN.book Page 70 Monday, May 7, 2007 3:31 PM Setup Recording Clock Items (highlight is the default) OFF 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes Insert chapter marks at even time interval. Recording Audio Select (XP) page 36 PCM Dolby Digital Set the recording audio type. (Only when the Rec Mode is set to XP.) Auto Finalise page 46 ON OFF Set the unit to finalise the disc automatically.
E7J70BD_EN.book Page 71 Monday, May 7, 2007 3:31 PM “General Setting” using [U / D], then press [ENTER/OK]. Select “Playback” using [U / D], then press [ENTER/OK]. Connections 2 Introduction Playback 1 In stop mode, press [SETUP]. Select Note • The parental lock function may not be available on some discs. • It may be difficult to determine if some DVDs support the parental lock function. Be sure to confirm that the parental lock function operates in the way that you have set.
E7J70BD_EN.book Page 72 Monday, May 7, 2007 3:31 PM Dynamic Range Control (Default: ON) Set to “ON” to make the dynamic range narrower. Select a setting using [U / D], then press [ENTER/OK]. Settings for MPEG (Default: PCM) Select a setting using [U / D], then press [ENTER/OK]. MPEG PCM Stream Dynamic Range Control ON OFF Your setting is activated. The Dynamic Range Control function is effective only with analogue audio connection.
E7J70BD_EN.book Page 73 Monday, May 7, 2007 3:31 PM Set the Subtitle language. Select a setting using [U / D], then press [ENTER/OK]. Subtitle Language Your setting is activated. If “Other” is selected, enter the appropriate 4-digit code using [the Number buttons]. Refer to “Language Code” on page 82. - - - When you finish entering the code, press [ENTER/OK]. Hint Note 6. Angle Icon (Default: ON) Set the angle icon. Select a setting using [U / D], then press [ENTER/OK]. Angle Icon ON OFF 7.
69_77_Function Setup_EN.fm Page 74 Friday, July 13, 2007 5:36 PM Display 1 In stop mode, press [SETUP]. Select Video 1 In stop mode, press [SETUP]. Select 2 2 “General Setting” using [U / D], then press [ENTER/OK]. Select “Display” using [U / D], then press [ENTER/OK]. “General Setting” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 75 Monday, May 7, 2007 3:31 PM 1 Select the desired setting using [U / D], then press [ENTER/OK]. DivX® In stop mode, press [SETUP]. Select “General Setting” using [U / D], then press [ENTER/OK]. 2 Select “DivX” using [U / D], then press [ENTER/OK].
E7J70BD_EN.book Page 76 Monday, May 7, 2007 3:31 PM 3. RGB Range (Default: Normal) HDMI 1 In stop mode, press [SETUP]. Select “General Setting” using [U / D], then press [ENTER/OK]. 2 Select “HDMI” using [U / D], then press [ENTER/OK]. Select the desired item using [U / D], then press [ENTER/OK]. 1 Format 2 HDMI Audio 3 RGB Range 4 Refer to 1. to 3. on this page and set the selected item. 5 When you finish with the setting, press [SETUP] to exit. 1.
E7J70BD_EN.book Page 77 Monday, May 7, 2007 3:31 PM Introduction Reset All 1 In stop mode, press [SETUP]. Select “General Setting” using [U / D], then press [ENTER/OK]. Select “Reset All” using [U / D], then press [ENTER/OK]. Connections 2 General Setting 3 Basic Setup Playback Display Video Recording Clock Channel DivX HDMI Reset All Select “Yes” using [U / D], then press [ENTER/OK]. Recording Reset to factory default? Yes No “Are you sure?” will appear.
E7J70BD_EN.book Page 78 Monday, May 7, 2007 3:31 PM Others Troubleshooting Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment by you may eliminate the problem and restore correct operation. DVD Symptom 78 Remedy The power does not turn on. • Check the mains cable is connected securely. • Check the breaker (in case of power failure). There is no picture.
E7J70BD_EN.book Page 79 Monday, May 7, 2007 3:31 PM Introduction DVD Symptom Remedy • If the Setup menu display appears, press [SETUP] or [RETURN/BACK] to turn off the display. Picture noise appears. • The disc is dirty or flawed. • If the unit is connected to your TV via a VCR, or if it is connected to a combination TV / VIDEO player, the copy-protection signal applied to some DVD programme could affect picture quality. Try connect the unit directly to your TV. Playback image freezes for a moment.
E7J70BD_EN.book Page 80 Monday, May 7, 2007 3:31 PM HDMI Symptom Remedy No image from HDMI connection. • Check the HDMI connection. (Check the status of the HDMI related indications.) • Check whether the connected monitor device or other device supports HDCP. (This unit will not output a video signal unless the other device supports HDCP.) • Check the setting of HDMI. • Check whether the output format of this unit (HDMI FORMAT) matches the supported input format of other connected device.
E7J70BD_EN.book Page 81 Monday, May 7, 2007 3:31 PM Cause Introduction Error message Solution • An unplayable disc is inserted in the unit. • The disc is upside down. • Insert a standard disc. (See pages 9-10.) • Insert the disc with the labelled side facing up. Region Error — Please eject the disc. — Playback is not authorized in your region. • Playback is not authorised in the region of the DVD-Video that you inserted in the unit. • Insert a DVD-Video with region codes 2 or ALL.
E7J70BD_EN.
E7J70BD_EN.book Page 83 Monday, May 7, 2007 3:31 PM Introduction Glossary Region code Regions associate discs and players with particular areas of the world. This unit will only play back discs that have compatible region codes. You can find the region code of your unit by looking on the rear panel. Some discs are compatible with more than one region (or all regions). Sampling frequency The rate at which sound is measured by a specified interval to turn it into digital audio data.
E7J70BD_EN.book Page 84 Monday, May 7, 2007 3:31 PM Specifications General System DVD-Video, DVD-RW/-R, DVD+RW/+R, CD-DA, CD-RW/-R Power requirements 220–240 V Power consumption 30 W (standby: 6 W) Weight 2.4 kg ± 10%, 50 Hz ± 0.
E7J70BD_EN.
E7J70BD_EN.
E7J70BD_EN.
78_88_Others_EN.