Projector User Manual
42
43
Operations
Using the menus (Continued)
Default setting 2 menu
Item
Description
Projection
mode
Sets projection mode in accordance with Placement Style.
p.21
(Standard)
(Rear)
(Ceiling)
(Rear ceiling)
Fan mode Sets the cooling fan speed. Standard
High
Remote control When 2 projectors are used and controlled by the remote control respectively,
this menu sets the code for the projector and the remote control.
[ or : Enter setting] [
: Select from 1, 2
] [ : Confirm]
[
:Select OK to end
]
Press [Cancel] to return.
Key lock Lock the control panel buttons.
[ or : Enter setting] [
: Select On/Off
] [ : Confirm]
[
:Select OK to end
]
Press [Cancel] to return.
Lamp power
Set the lamp power.
Low
Standard
Reset all
Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings. Yes
No
Password
Password setting
p.33
Press . Password registration/Password setting
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500
meters above sea level).
Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from 2 types. You can set each code respectively for up to
2 projectors. The factory setting is [
1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
You cannot operate the remote control if the codes of the projector and the remote
control do not match.
Remote control code setting for remote control
Set the same remote control code switch as the projector.
p.16
p.17
•
•
[Key lock]
Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
with the control panel buttons is disabled.
To release the key lock, set the [Key lock] to [Off] using remote control. Pressing
the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off].
(When operating the main unit, the 2 indicators of LAMP and TEMP light in orange
for 3 seconds, and at the same time the projector beeps.).
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item Description
Digital (DVI)
Analog (D-SUB)(DVI)
Video
S-video
RGB
Y/PB/PR
RGB
Y/PB/PR
Input Input source name Yes Yes Yes Yes Yes Yes
Mode name RGB input mode
[Note 1]
Yes No Yes No No No
Resolution Resolution (in dots) Yes No Yes No No No
Frequency Sync frequency Yes No Yes No No No
Sync Sync signal polarity
[Note 2]
Yes No Yes No No No
Signal format Y/PB/PR signal format No Yes No Yes No No
Video mode Color method of video signal No No No No Yes Yes
Lamp time Time of lamp use
[Note 3]
Yes Yes Yes Yes Yes Yes
Lamp reset count
The count for lamp replacement
Yes Yes Yes Yes Yes Yes
Total time
The total time that this
projector is used.
Yes Yes Yes Yes Yes Yes
Version Firmware version
[Note 4]
Yes Yes Yes Yes Yes Yes
Notes
1: The mode of supported RGB signals
p.53
is shown.
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [
Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000
hours, consult with a dealer about getting replacement for:
TLPLW40 (sold separately).
4: [
Version] shows the version of the projector’s internal control program. This version will
be requested for customer service purposes.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
•
•