E7TE0BD_EN.book Page 1 Friday, March 5, 2010 5:08 PM Introduction OWNER’S MANUAL Basic Setup / TV View Operation DR20KB Connections DVD VIDEO RECORDER Recording Playback Editing Function Setup EN 1 Others © 2010 Toshiba Corporation For Customer Use: Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. __________________________ Serial No.
E7TE0BD_EN.book Page 2 Friday, March 5, 2010 5:08 PM . Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
E7TE0BD_EN.book Page 3 Friday, March 5, 2010 5:08 PM Installation Location For safety and optimum performance of this unit: • Install the unit in a horizontal and stable position. • Keep the unit away from electronic equipment such as an amplifier, TV, etc. to prevent warping,damage, fire and malfunction. • Do not place anything directly on top of the unit. • Shield the unit from direct sunlight and keep away from sources of intense heat. Avoid dusty or humid locations.
E7TE0BD_EN.book Page 4 Friday, March 5, 2010 5:08 PM Notice for the Progressive Scan Outputs Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 480 or 576 progressive scan output, it is recommended that the user switch the connection to the ‘standard definition’ output.
E7TE0BD_EN.book Page 5 Friday, March 5, 2010 5:08 PM • • • • • Remote control with 2 R6 (1.
E7TE0BD_EN.book Page 6 Friday, March 5, 2010 5:08 PM Table of Contents Introduction ...................................................... 2 Editing ............................................................. 53 Precautions ........................................................................ 2 Guide to a Title List .......................................................... 53 Features ............................................................................. 5 Editing Discs ................
E7TE0BD_EN.book Page 7 Friday, March 5, 2010 5:08 PM Introduction Guide to the Owner’s Manual Symbols Used in the Owner’s Manual Symbol Connections To show what recording mode or media type applies to each function, the following symbols appear at the beginning of each operating item.
E7TE0BD_EN.book Page 8 Friday, March 5, 2010 5:08 PM Discs for Recording / Playing Disc Type DVD-RW DVD-R DVD+RW DVD+R Logo Automatically formatted in video mode Format Can be formatted in VR or video mode Video Mode Icon Maximum Record Time VR DVD-RW DVD-RW 480 min (12 cm) 144 min (8 cm) 480 min (12 cm) 144 min (8 cm) Playable on most DVD players. Finalisation Compatibility necessary.
E7TE0BD_EN.
E7TE0BD_EN.book Page 10 Friday, March 5, 2010 5:08 PM Functional Overview Front Panel 1*2 3*1 4 2 5 6 7 8 9 10*1 11 15 14 13 12 You can also turn on the unit by pressing these buttons. Press to turn on the unit, or to turn the unit into the standby mode. (To completely shut down the unit, you must unplug the AC power cord.
E7TE0BD_EN.book Page 11 Friday, March 5, 2010 5:08 PM 17 18 19 3 21 22 5 23 6 24 7 25 8 26 9 27 28 12 29 30 31 13 15 16 32 33 34 Button names described in the Owner’s Manual The instructions in this manual are described mainly with the operations using the remote control. Some operations can be carried out using the buttons on the front panel.
E7TE0BD_EN.book Page 12 Friday, March 5, 2010 5:08 PM Installing Batteries in the Remote Control Install 2 R6 (1.5 V) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment. 1 2 3 Guide to On-Screen Displays DISPLAY Menu With a disc inserted into the unit, press [DISPLAY] to display the on-screen display. The on-screen display shows information about what is recorded on the disc.
E7TE0BD_EN.book Page 13 Friday, March 5, 2010 5:08 PM INFO Menu DVB
Title name information Press [INFO C] while viewing a DVB programme to display the programme information. 4ITLE .E7TE0BD_EN.book Page 14 Friday, March 5, 2010 5:08 PM A General Setting B Timer Programming To programme a timer recording. [E Page 32] 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 General Setting Playback Display Video Recording Clock Channel DivX HDMI DVB Setting Reset All Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode TV System C Title List To call up the title list.
E7TE0BD_EN.book Page 15 Friday, March 5, 2010 5:08 PM Introduction Front Panel Display Guide 1 2 DTV 3 Connections 4 1 DTV indicator : Appears when a disc is in this unit.
E7TE0BD_EN.book Page 16 Friday, March 5, 2010 5:08 PM Connections Connecting to a TV Connect the unit to a TV after considering the capabilities of your existing equipment. Before installation, unplug your TV and this unit Cable Signal Antenna or To Aerial jack RF cable (not supplied) 1 RF cable (supplied) • When changing the “Video Out” setting (“SCART (RGB)”, “Component (Interlace)” or “Component (Progressive)”), connect to the corresponding jack on the TV.
E7TE0BD_EN.book Page 17 Friday, March 5, 2010 5:08 PM HDMI cable (not supplied) To HDMI input jack this unit HDMI IN Selecting HDMI video resolution Press [HDMI] to select the HDMI video resolution. The video resolution changes as follows every time [HDMI] is pressed. 576p (PAL) / 480p (NTSC) J 720p J 1080i J 1080p (An HDMI video resolution that is not supported by the display device will be skipped.
E7TE0BD_EN.book Page 18 Friday, March 5, 2010 5:08 PM Connecting to External Equipment This unit has four input terminals. Press [INPUT SELECT F] repeatedly to select the external input mode, then press [PROG. G \ H] repeatedly to select AV1, AV2, AV3 or DV(AV4). Be sure that all the units are switched off before making connections.
E7TE0BD_EN.book Page 19 Friday, March 5, 2010 5:08 PM Introduction Basic Setup / TV View Operation Initial Setting Press [B ON\STANDBY]. 3 Select your desired tuning type according to your area using [K \ L], then press [ENTER\OK]. Turn the TV on. Select the input to which the unit is connected. Selecting the TV Aspect Ratio Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture.
E7TE0BD_EN.book 3 Page 20 Friday, March 5, 2010 5:08 PM Select “Auto Tuning (DVB & ANALOG)” using [K \ L], then press [ENTER\OK]. The unit will start storing channels available in your area. General Setting Playback Display Video Recording Clock Channel DivX HDMI DVB Setting Reset All Auto Tuning (DVB & ANALOG) DVB Channel Setup ANALOG Channel Setup Wait for several minutes to finish channel storing.
E7TE0BD_EN.book Page 21 Friday, March 5, 2010 5:08 PM ANALOG Channel Search S.No. TV Channel You can set the unit to skip channels. You can no longer receive or watch when you access channels using [PROG. G \ H]. Follow steps 1 to 4 in “Manual Tuning (ANALOG)” on page 20. 2 3 Select “Position” using [K \ L], then press [1]. 4 5 Select “Skip” using [K \ L], then press [1]. Select “ON” using [K \ L], then press [0]. • To skip another channel, repeat steps 2 to 5. Press [SETUP] to exit.
E7TE0BD_EN.book Page 22 Friday, March 5, 2010 5:08 PM Quick Select TV View Operation DVB The following operations are available while viewing TV channels through this unit’s tuner. 1 Select a Channel DVB With “Quick Select” menu, you can select your favourite DVB channel quickly. Refer to “Edit Group Lists” on page 23. ANALOG • “Quick Select” menu will appear. To switch DVB, analogue and external input (AV1/AV2/AV3/ DV(AV4)) mode.
E7TE0BD_EN.book Page 23 Friday, March 5, 2010 5:08 PM Edit Group Lists DVB DVB With “Edit Channels” menu, you can sort all the memorised DVB channels into the group lists (“Quick Select”) or set the viewer limitation (“Adult Lock”), etc. 1 Select “Channel” using [K \ L], then press [ENTER\OK]. Select “DVB Channel Setup” using [K \ L], then press [ENTER\OK]. 4 Select “Edit Channels” using [K \ L], then press [ENTER\OK]. Follow steps 1 to 4 in “Edit Channels” on this page.
E7TE0BD_EN.book Page 24 Friday, March 5, 2010 5:08 PM Adult Lock Channel Move DVB DVB You can set the unit to limit the access to the DVB channels. 1 2 Follow steps 1 to 4 in “Edit Channels” on page 23. Select the DVB channel you want to limit the access using [K \ L], then press [YELLOW]. Edit Channels S.No. Channel Name 5 Fav. Skip Lock Del. Five England Crystal Palac Re Name Skip You can change the order of the DVB channels when you use [PROG. G \ H].
E7TE0BD_EN.book Page 25 Friday, March 5, 2010 5:08 PM Multi Audio DVB DVB You can check the detailed information of the current DVB channel. 1 1 Select “Signal Information” using [K \ L], then press [ENTER\OK]. While viewing a DVB programme, press [AUDIO D]. Connections 2 Follow steps 1 to 3 in “Auto Tuning (DVB)” on page 21. Many DVB channels transmit Multi Audio information along with their DVB channels. You can select the desired audio mode and audio language.
E7TE0BD_EN.book Page 26 Friday, March 5, 2010 5:08 PM e.g.) Weekly Mode Note • If the programme is changed, the subtitle language will be switched back to the default language you set in the “DVB Setting”. Refer to “B Language” on page 68. If the default subtitle language is not available on the new programme, no subtitle will be displayed. 1 2 Mon Tue Mon 17/05 3 Audio Description DVB You can receive “Audio Description” service via DVB channels and listen to it as a sub-audio.
E7TE0BD_EN.book Page 27 Friday, March 5, 2010 5:08 PM Introduction Recording Restrictions on Recording Information on DVD Recording Some satellite broadcasts include copy-protected information. If you want to record them, refer to the following. Media type / format VR DVD-RW Video DVD-R ver. 1.1 / ver. 1.2 ver. 1.1 / ver. 1.2 CPRM compatible ver. 1.1 / ver. 1.
E7TE0BD_EN.book Page 28 Friday, March 5, 2010 5:08 PM Making Discs Playable in Other DVD Players (Finalise) After recording, you must finalise the disc to play it back in other players. (See page 40.) You cannot finalise discs in other DVD recorders. Disc Type DVD-R DVD-RW Video Mode VR Mode DVD+RW DVD+R ✔ ✔ After finalising ✔ Automatic Title menu making Undo finalising (See page 40.) Additional recording or editing (See page 40.
E7TE0BD_EN.book Page 29 Friday, March 5, 2010 5:08 PM Introduction Make Recording Compatible Formatting a Disc Choosing the Recording Format of a Blank DVD-RW Disc Video VR In stop mode, press [SETUP]. In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK]. 3 Select “Make Recording Compatible” using [K \ L], then press [ENTER\OK]. 4 Select “ON” or “OFF” using [K \ L], then press [ENTER\OK].
E7TE0BD_EN.book Page 30 Friday, March 5, 2010 5:08 PM Setting Auto Chapter Video 1 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK]. 3 Select “Auto Chapter” using [K \ L], then press [ENTER\OK]. 4 If you want to set “Auto Chapter” off, select “OFF” using [K \ L], then press [ENTER\OK].
E7TE0BD_EN.book Page 31 Friday, March 5, 2010 5:08 PM Video DVD-RW DVD-R DVD+RW DVD+R You can select either “Main” or “Sub” audio to record a bilingual broadcast in video mode or +VR mode. This setting is only for recording analogue channel. Basic Recording and One-touch Timer Recording (OTR) DVB ANALOG 1 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. DVD-RW DVD-RW DVD-R DVD+RW DVD+R Follow the steps below to record a TV programme.
E7TE0BD_EN.book Page 32 Friday, March 5, 2010 5:08 PM • When the unit reaches the specified time, it will be turned off automatically. • To change the recording length during One-touch Timer Recording, press [REC I] repeatedly until the desired length appears. • To cancel One-touch Timer Recording within the specified time, press [STOP C]. 8 Press [STOP C] to stop the recording. This operation may take a few moments to complete. Note • You can change the channel while in the REC pause mode.
E7TE0BD_EN.book Friday, March 5, 2010 5:08 PM Select the digital (DVB) / analogue (ATV) mode or external input (AV1/AV2/AV3) using [K \ L], then press [1]. 6 Select the channel number to record using [K \ L], then press [1]. 7 Select the recording mode using [K \ L], then press [1]. 8 For DVB channel recording: Select “STTL” to “ON” or “OFF” using [K \ L]. If you set “STTL” to “ON”, subtitle will be recorded too. • When analogue channel is selected, “PDC” will be displayed instead of “STTL”.
E7TE0BD_EN.book Page 34 Friday, March 5, 2010 5:08 PM Checking, Cancelling or Correcting the Timer Programming Information 1 Press [B ON\STANDBY] to cancel the timer-standby mode. 2 Press [TIMER PROG.]. If the Timer Programming did not Complete Correctly The error number appears on “Timer Programming” list. Timer Programming “Timer Programming” list will appear. 3 B) To correct the timer programme: 1) Select the programme you want to correct using [K \ L], then press [ENTER\OK].
E7TE0BD_EN.book Page 35 Friday, March 5, 2010 5:08 PM PROG. 2 recording will start after PROG. 1 recording is completed. PROG. 1 PROG. 2 PROG. 1 Actual recording PROG. 1 * If the cut off time exceeds 3 minutes, the error number “E40” will appear in “Timer Programming” list. Timer Recording (EPG) DVB Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R With EPG system, you can programme DVB channel recording much easier. You can only choose one programme and enter the selection.
E7TE0BD_EN.book Page 36 Friday, March 5, 2010 5:08 PM Series Link Timer Recording Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R With the EPG system, when you set a TV programme into the timer recording, you can also set for future episodes of that series to be recorded. It is also possible to set for the broadcaster to recommend related programmes to you. 1 While viewing a DVB programme, press [GUIDE]. • List of DVB programmes will be displayed.
E7TE0BD_EN.book Page 37 Friday, March 5, 2010 5:08 PM • If you have not set the clock, the clock setting window will appear and follow to “A Clock Setting” on page 66. • You cannot set the End time for the satellite link timer recording on this unit. • [SAT.LINK] does not work under the following circumstances: - Setup menus are displayed. - “Timer Programming” menu is displayed. - Title list or any file list is displayed. - During playback of DVD. - During recording or dubbing of DVD.
E7TE0BD_EN.book Page 38 Friday, March 5, 2010 5:08 PM Recording from External Equipment Video 3 Press [DISPLAY] to display the DVC information on the screen. VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R Before recording from external equipment, see page 18 for connection instructions. When the DVC is in video mode... 1 1 2 Turn on the TV and be sure to select the input to which the unit is connected. 2 Press [OPEN\CLOSE A] to open the disc tray, then place the disc to record on.
E7TE0BD_EN.book Friday, March 5, 2010 5:08 PM Status of the current operation and the time counter 4 Each icon means (Available icons may vary depending on the DVC): With “Control” highlighted, press [ENTER\OK] to display the available devices to control with the remote control of this unit. Select “DVC” using [K \ L], then press [ENTER\OK]. e.g.) DVC to DVD dubbing DVC is in stop mode. DVC is in playback mode. T 1/ 1 C 1/ 1 DVC is in pause mode. -RW DVC is fast forwarding.
E7TE0BD_EN.book Page 40 Friday, March 5, 2010 5:08 PM Setting a Disc to Protect VR To cancel finalising (DVD-RW disc only): At step 4, press [STOP C]. Select “Yes” using [K \ L], then press [ENTER\OK]. Finalising is cancelled and the unit switches to stop mode. DVD-RW DVD+RW DVD+R To prevent accidental over-recording, editing or erasing of recordings, you can protect them using “Setup” menu. Do you want to cancel? Yes No Insert a recordable disc. 1 In stop mode, press [SETUP].
E7TE0BD_EN.book Page 41 Friday, March 5, 2010 5:08 PM Introduction Playback 8 Note for DVD Playback Note The contents of an DVD are generally divided into titles. Titles are further subdivided into chapters depend on Auto Chapter setting (See page 30). Stop Rec./Start Rec. Title 2 Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2 Playing Back a DVD-V / Video CD (without PBC Function) 1 VR DVD-RW DVD-RW DVD-R DVD+RW DVD-V DVD+R Press [B ON\STANDBY] to turn on the unit.
E7TE0BD_EN.book Page 42 Friday, March 5, 2010 5:08 PM Playing Back an Audio CD or a Disc with MP3 / JPEG / DivX® Files MP3 CD JPEG DivX ® 1 Follow steps 1 to 4 in “Playing Back a DVD-RW / DVD-R / DVD+RW / DVD+R Disc” on page 41. 2 If you want to play back an audio CD or a disc with a single file type (e.g., a disc containing MP3 files only), skip to step 4. If you want to play back a disc with mixed file types, proceed to step 3.
E7TE0BD_EN.book Page 43 Friday, March 5, 2010 5:08 PM The subtitle created by the user can be displayed during DivX® playback. After the DivX® file is selected, “Subtitle List” will appear. 2 Select the desired extension of the subtitle file you want to display using [K \ L], then press [ENTER\OK]. DivX® with the subtitle starts playback. The subtitle cannot be displayed when the setting is “OFF”. • If there is more than one extension, the extension selection will appear in “Subtitle List”.
E7TE0BD_EN.book Page 44 Friday, March 5, 2010 5:08 PM • Files whose extension other than “.avi” and “.divx” will not be listed on the DivX® menu. However, unplayable groups or tracks may be displayed, depending on the recording conditions. • Even if the file has an extension of either “.avi” and “.divx”, this unit cannot play it back if it is recorded in the format other than DivX®. • Folders are known as Groups; files are known as tracks. • A symbol of is shown on the top of the file name.
E7TE0BD_EN.book Page 45 Friday, March 5, 2010 5:08 PM VCD (PBC OFF) Insert a video CD. 1 In stop mode, press [SETUP]. 2 Select “DISC Playback Mode” using [K \ L], then press [ENTER\OK]. 3 Select “PBC (Video CD only)” using [K \ L], then press [ENTER\OK]. Connections VCD This unit conforms to ver.1.1 and ver.2.0 of the video CD standard playback control (PBC) function. This enables you to play back interactive software using menu screens. Refer to the information accompanying the video CD. Ver.1.
E7TE0BD_EN.book Page 46 Friday, March 5, 2010 5:08 PM Fast Forward / Fast Reverse DVD-V DVD+R 1 Video VR DVD-RW DVD-RW CD VCD Step by Step Playback DVD-R MP3 DVD+RW DivX ® During playback, press [FWD D] or [REV E]. Each time you press [FWD D] or [REV E], the approximate speed will change as follows. Fast forward or fast reverse playback across titles (for DVDs) or tracks / files (for video CD / MP3 / DivX®) is not possible.
E7TE0BD_EN.book Page 47 Friday, March 5, 2010 5:08 PM Note Video VR DVD-V DVD-RW DVD-RW DVD+R VCD JPEG DVD-R DVD+RW DivX ® During playback, press [DISPLAY] to bring up the display menu. 2 Select the icon using [0 \ 1] to display the selection menu. T 1/ 5 C 1/ 5 0:01:00 / 1:23:45 DVD Video × 1.2 × 1.5 × 2.0 Chasing Playback during Recording Select the desired zoom factor to zoom using [K \ L], then press [ENTER\OK]. The zoom area is displayed.
E7TE0BD_EN.book Page 48 Friday, March 5, 2010 5:08 PM Using the [TIME SLIP] button With [TIME SLIP], even if you leave your couch while you are watching TV through this unit, you can come back and watch rest of the programme from right where you left at any convenient time with just one button. Please make sure to put VR mode DVD-RW disc, and set the recording mode to LP, EP or SLP.
E7TE0BD_EN.book Page 49 Friday, March 5, 2010 5:08 PM Search CD Title / Chapter Search DVD-V VR DVD-RW DVD-R JPEG DivX ® DVD+R Using [SKIP H \ G] buttons 1 During playback, press [SKIP G] to skip the current track and move to the next. The unit moves to the next track one after another. To go back to the previous track, press [SKIP H] twice in quick successions. The unit moves backward one track at a time.
E7TE0BD_EN.book Page 50 Friday, March 5, 2010 5:08 PM A-B: The A-B point will be played back repeatedly. (DVD, audio CD, video CD and DivX® only) When pressing [ENTER\OK] while A-B is highlighted, A-B repeat is set. • Press [ENTER\OK] again to decide the starting point (A). • Press [ENTER\OK] after setting point (A) to select the ending point (B).
E7TE0BD_EN.book Page 51 Friday, March 5, 2010 5:08 PM Introduction Programme Playback Selecting the Format of Audio and Video VCD CD (PBC OFF) You can programme the disc to play back in your desired order. Follow steps 1 to 2 in “Random Playback” on page 50. 2 Select “Programme Play” using [K \ L], then press [ENTER\OK]. 3 Select the desired track using [K \ L], then press [ENTER\OK] or [1].
E7TE0BD_EN.book 3 Page 52 Friday, March 5, 2010 5:08 PM Select a desired audio soundtrack or audio channel using [K \ L], then press [ENTER\OK]. With a DVD-video, VR mode DVD-RW, or DivX® files: Audio soundtrack will switch. Example: English J Spanish J French If the title contains both main and sub audio, you can further select L (main), R (sub), L/R (mixed of main and sub). With an audio CD or video CD: The Audio channel will switch.
E7TE0BD_EN.book Page 53 Friday, March 5, 2010 5:08 PM Introduction Editing 1 Guide to a Title List Press [TOP MENU]. 4 5 6 Title List PL ABCDE 12:00 (2:00:00) 17/05/10 +VR 1 LP 1 2 3 4 5 6 Video 3 2 ORG 1 3 Edit 1 Press [RETURN\BACK] to exit the title list. Playback Scene Delete Edit Title Name Chapter Mark Protect Recording 1/2 Basic Setup / TV View Operation ORG ORG Connections Title list allows you to check the titles recorded on the disc easily.
E7TE0BD_EN.book Page 54 Friday, March 5, 2010 5:08 PM Deleting Titles Editing Discs You will find editing discs is easy. This unit offers convenient edit functions. You can edit the following from a title list. • Assigning a name to a title • Dividing a title • Combining titles • Adding titles to a Playlist • Setting or releasing the title protection • Adding or deleting chapter marks • Deleting titles or parts of titles (Possible editing functions depend on the recording format and editing method.
E7TE0BD_EN.book Page 55 Friday, March 5, 2010 5:08 PM Video Guide to Editing Title Names VR DVD-RW DVD-R DVD-RW DVD+RW DVD+R You can edit the title names from this menu. The title names you edit will appear on the title list. 1 In stop mode, press [TOP MENU]. 2 Step 2 : Using the list below as a guide, press [the Number buttons] repeatedly until the desired letter appears. Select Press 5 @!? 0 ! ”# $ % & ’( ) ∗+,-./:;<=> ?@[]^_{|} – 1 Edit menu will appear.
E7TE0BD_EN.book Page 56 Friday, March 5, 2010 5:08 PM Adding or Deleting Chapter Markers Manually Adding or Deleting Chapter Marks at once for Video Mode DVD-RW disc VR DVD-RW Video DVD+RW DVD+R You can add chapter marks to a title. After a title is marked with chapters, you can use the chapter search feature. You can set a chapter mark anywhere you want. 1 Follow the steps 1 to 3 in “Editing Title Name” on page 55. 2 Select “Chapter Mark” using [K \ L], then press [ENTER\OK].
E7TE0BD_EN.book Page 57 Friday, March 5, 2010 5:08 PM Introduction Hiding Chapters Dividing a Title VR DVD+RW DVD+R DVD-RW DVD+RW Playlist 1 Follow the steps 1 to 3 in “Editing Title Name” on page 55. 1 Follow steps 1 to 3 in “Editing Title Name” on page 55. 2 Select “Hide Chapter” using [K \ L], then press [ENTER\OK]. 2 3 Use [SKIP H \ G], [PLAY B] and [PAUSE F] to decide the chapter to be hidden.
E7TE0BD_EN.book Page 58 Friday, March 5, 2010 5:08 PM Combining Titles Adding Titles to a Playlist VR VR DVD-RW DVD-RW Playlist Original You can combine two titles into a single title. 1 For VR mode DVD-RW disc, you can add a title to the Playlist as you want. Follow steps 1 to 3 in “Editing Title Name” on page 55. 1 2 Select “Title Combining” using [K \ L], then press [ENTER\OK]. Follow the steps 1 to 2 in “Deleting Titles” on page 54.
E7TE0BD_EN.book Page 59 Friday, March 5, 2010 5:08 PM Deleting Parts of Titles VR VR DVD-RW All Playlists can be deleted if it is no longer needed. Press [SETUP]. 3 Select “Delete All Playlists” using [K \ L], then press [ENTER\OK]. Select “DVD Menu” using [K \ L], then press [ENTER\OK]. Format Finalise Disc Protect OFF A ON Delete All Playlists Follow the steps 1 to 3 in “Editing Title Name” on page 55. 2 Select “Scene Delete” using [K \ L], then press [ENTER\OK].
E7TE0BD_EN.book Page 60 Friday, March 5, 2010 5:08 PM Function Setup The following table is the contents which you can set and the default settings. Refer to the following table for useful operation.
E7TE0BD_EN.book Clock Channel 5:08 PM Contents Clock Setting E Page 66 Auto Clock Setting E Page 67 Auto Tuning (DVB & ANALOG) E Page 19 DVB Channel Edit Channels Setup E Page 23 Auto Tuning E Page 21 Manual Tuning E Page 21 Signal Information E Page 25 ANALOG Auto Tuning Channel Setup E Page 20 Manual Tuning E Page 20 Move E Page 21 DivX® VOD E Page 43 Set the clock manually. Set the clock automatically. ON OFF Tune the DVB and analogue channels automatically.
E7TE0BD_EN.book Page 62 Setup Friday, March 5, 2010 5:08 PM Items (highlight is the default) Adult Lock E Page 68 Language E Page 68 General Setting DVB Setting Audio Subtitle Data Service Contents ON OFF English Gaelic Welsh English Gaelic Welsh English Gaelic Welsh Set the Adult Lock and change Pincode. Set the Audio language. Set the Subtitle language. Set the Digital Teletext language. About E Page 68 Check the current DVB system software version of the unit. Set to the default setting.
E7TE0BD_EN.book Page 63 Friday, March 5, 2010 5:08 PM Setup A General Setting A Playback Introduction Playback A password is already set 1 Enter the current password using [the Number buttons]. Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode TV System Password Input 2-A Select “No” using [K \ L], then press [ENTER\OK]. Change Password? Yes No A Parental Lock (Default: OFF) “Parental Lock” level is activated.
E7TE0BD_EN.book Page 64 Friday, March 5, 2010 5:08 PM PCM sampling (Default: 48kHz) C Disc Menu Language (Default: English) Set “Disc Menu Language”. PCM Disc Menu Language 48kHz 96kHz 48kHz : If your amplifier / decoder is NOT compatible with 96 kHz PCM, select “48kHz”. Sound recorded at 96 kHz is down sampled to 48 kHz. 96kHz : If your amplifier / decoder is compatible with 96 kHz PCM, select “96kHz”. Sound is sampled at 96 kHz.
E7TE0BD_EN.book Page 65 Friday, March 5, 2010 5:08 PM Still Mode Display Setup A General Setting A Display Auto Field Frame : Automatically select the best resolution setting (“Frame” or “Field”) based on the data characteristics of the pictures. Field : Select “Field” when the pictures are still unstable even if “Auto” is selected. “Field” stabilises the pictures, although the picture quality may become coarse due to the limited amount of data.
E7TE0BD_EN.book Page 66 Friday, March 5, 2010 5:08 PM 3 Select “Yes” using [K \ L], then press Video [ENTER\OK] within 15 seconds. Setup A General Setting A Video Confirm again to use progressive scan. If picture is good, select “Yes”. A TV Aspect B Select Video C Video Out A TV Aspect (Default: 16:9 Wide) Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture.
E7TE0BD_EN.book Page 67 Friday, March 5, 2010 5:08 PM Auto Clock Setting ON OFF [ENTER\OK]. 2 Press [SETUP] to exit. 3 Press [B ON\STANDBY] to turn the unit off. Note A B C D Format HDMI Audio RGB Range HDMI CEC A Format (Default: RGB) You can select the colour space for HDMI output. Set the appropriate colour space for your display device. • When the connected device is not compatible with the Y/Cb/Cr, HDMI signal is output as RGB regardless of the setting.
E7TE0BD_EN.book Page 68 Friday, March 5, 2010 5:08 PM System information Power off: When you turn the TV off, this unit and all equipment connected via an HDMI cable will automatically be turned off except during recording on the unit. Receiving operational signal from TV’s remote control: You can operate this unit with TV’s remote control. Check your TV owner’s manual for details. Note • This function may not work properly depending on the connected TV.
E7TE0BD_EN.book Page 69 Friday, March 5, 2010 5:08 PM Introduction Others Troubleshooting • Check that the AC power cord is connected securely. • Batteries of the remote control are weak. The unit turns on automatically without any operation. • The unit turns on automatically 2 seconds before the timer recording. The unit does not function. • “ ” or error message appears if the operation is prohibited. • Batteries of the remote control are weak or exhausted.
E7TE0BD_EN.book Page 70 Friday, March 5, 2010 Symptom Remedy CHANNEL TV channels cannot be changed. • Check if the connections are made securely and correctly. • Check if the cables are damaged. • Try “Channel” setting by following the steps on pages 19-21. Some settings are lost even though you • If you unplug the AC mains cable while the warning message, “Saving settings. followed the procedure correctly. Please wait.”, is displayed, some settings may be lost.
E7TE0BD_EN.book Page 71 Friday, March 5, 2010 5:08 PM PLAYBACK • Resume function may be activated. Refer to page 45 to cancel the resume point. Playback cannot be performed. • Check if the playable disc is inserted. • Check if the disc is loaded correctly with the labelled side facing up. • Discs made on other devices or on personal computers cannot be played back on this unit unless it is finalised on the device.
E7TE0BD_EN.book Page 72 Friday, March 5, 2010 5:08 PM REMOTE CONTROL Symptom Remedy The remote control does not function. • No batteries in the remote control or the batteries may be weak. Replace the batteries. • Make sure there is no obstacle between the remote control and the unit. • Try getting closer to the unit. (See page 12.) • If above solutions do not solve the problem, please call an Authorised Service Centre.
E7TE0BD_EN.book Page 73 Friday, March 5, 2010 Cause Introduction Error message 5:08 PM Solution • You are trying to record onto the DVD+RW disc on which the number of recording chapters comes up to the maximum (254). • Delete unnecessary chapter marks. (See page 56.) Recording Error You cannot record on this disc as Control Information is full. • This disc has no space to write Control Information when recording or deleting contents.
E7TE0BD_EN.
E7TE0BD_EN.book Page 75 Friday, March 5, 2010 5:08 PM Introduction Specifications General Power requirements 220–240 V Power consumption 26 W 0.74 W Weight 3.2 kg Dimensions (width x height x depth) 420 x 59 x 357 mm Operating temperature 5°C to 40°C Operating humidity Less than 80 % (no condensation) TV system PAL-I Connections Power consumption (standby) ± 10 %, 50 Hz ± 0.
E7TE0BD_EN.