TOSHIBA AMERICA INFORMATION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA MK6022GAX (HDD2184) 2.
CONTENTS Introduction..............................................................................1 Setup ........................................................................................2 Using the HDD .........................................................................4 Troubleshooting.......................................................................5 Specifications ..........................................................................6 Drive Connectors...............................
INTRODUCTION - MK6022GAX (HDD2184) General Features • Rotational speed of 5,400rpm • 2.5" sized drive • Fluid Dynamic Bearing (FDB) Motor • 2 Platter • 60 Gigabytes* • 9.5mm High • 12ms Average Seek Time • ATA-2,3,4,5 Interface • Supports high transfer rates of 100 MB/sec • 16MB Buffer • MTTF 300,000 Hours *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes.
SETUP – MK6022GAX (HDD2184) Caution: Your Hard Disk Drive is a precision device and even a small drop onto any surface can cause damage. Electronstatic discharge can also damage the drive. You should ground yourself prior to handling the drive. Master/Slave Settings Your Toshiba Hard Disk Drive can be configured as either a "Master" or "Slave" unit.
Installation Notes The drive should be mounted carefully on the surface of 0.1mm or less flatness to avoid excessive distortion. In order to prevent short-circuit under any circumstances, a space of 0.5mm or more should be kept under the PCB. Space should be kept around the drive to avoid any contact with other parts, which may occur due to shock or vibration. The temperature of the top cover and the base must always be kept under 60C to maintain the required reliability.
USING THE HARD DISK DRIVE – MK6022GAX (HDD2184) Backing up Data Files To avoid data loss, regularly back up the data files on the hard disk drive.
TROUBLESHOOTING – MK6022GAX (HDD2184) Problem My system is not able to recognize all available capacity on my Hard Disk Drive. What do I need to do to utilize the complete hard drive? How do I install my 2.5" Toshiba Hard Drive into my desktop or tower system? 5 Solution There are some systems that are unable to recognize the new larger Hard Drives on the market. 3rd party software is available that breaks the "capacity barrier".
SPECIFICATIONS –MK6022GAX (HDD2184) General Model Interface Motor MK6022GAX (HDD2184) ATA-2/3/4/5 Fluid Dynamic Bearing (FDB) Functionality Formatted Capacity 60.0116GB* Rotational Speed 5,400rpm Avg. Rotational Latency 5.55/ms Spin-up Time 4sec (typical) Buffer 16MB Seek Time (Average) 12 Internal Transfer Rate 200.8 ~ 333.2 Mbits/sec (max) Host Transfer Rate 100Mbytes/sec *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes.
Physical Height Width Depth Weight 0.37" (9.5mm) 2.75" (69.85mm) 3.94" (100mm) 3.563oz (101g) typ Regulatory The drive satisfies the following standards: Underwriters Laboratories (UL) 1950 Canadian Standard Association (CSA) C22.2 No.220 No.
DRIVE CONNECTORS –MK6022GAX (HDD2184) Figure 1.MK6022GAX HDD Rear View - Connectors Interface Connector Drive Side Connector Recommended Host Side Connector Board Cable Yamaichi GAP050K11617 or equivalent Straight type: Berg 86455-044 86456-044 or equivalent Berg 89361-044 or equivalent Recommended Cable Characteristics Standard diameter Characteristics impedance Max Length Capacitance * cable is not included with drive 8 0.32mm (28AWG) 100 - 132ohm 0.
Interface Pin Assignment DRIVE INTERFACE SIGNALS PIN SIGNAL PIN SIGNAL 1 RESET 2 GROUND 3 DD 7 4 DD 8 5 DD 6 6 DD 9 7 DD 5 8 DD 10 9 DD 4 10 DD 11 11 DD 3 12 DD 12 13 DD 2 14 DD 13 15 DD 1 16 DD 14 17 DD 0 18 DD 15 19 GROUND 20 KEY 21 DMARQ 22 GROUND 23 DIOW/STOP 24 GROUND 25 DIOR/ -DMARDY HSTROBE 26 GROUND 27 IORDY/ -DMARDY/DSTROBE 28 CSEL 29 DMACK 30 GROUND 31 INTRQ 32 IOCS16 33 DA1 34 PDIAG 35 DA0 36 DA 2 37 CS0 38 CS1 39 DA
