LCD TV/DVD COMBINATION 19DV615DG 19DV616DG 22DV615DG 22DV616DG 26DV615DG OWNER’S MANUAL ©2009 Toshiba Corporation Before operating the unit, please read this manual thoroughly. 52R0131A_ENG.indd 1 Ownerʼs Record The model number and serial number are on the back of your TV/DVD. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV/DVD.
Precautions CAUTION: THIS UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE UNIT. CLASS 1 LASER PRODUCT WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
Contents Precautions ........................................................... 2 Contents ............................................................... 3 Important safety information.................................. 4 Location of controls............................................... 6 Remote Control..................................................... 7 Aerial connection .................................................. 9 Auto setup...........................................................
Important safety information 4 This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use. • Although this appliance has been carefully manufactured and rigorously checked prior to leaving the factory, as with all electrical appliances it is possible for problems to develop.
Important safety information Where to install Locate the television away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen. Sturdy tie (as short as possible) Place on a sturdy platform, the mounting surface should be flat and steady.
Location of controls Disc slot 4 5 6 7 8 9 10 3 1 2 Adjusting the angle of the base (except 26DV615DG) You can adjust the angle of the TV-screen for 3° forward or for 10° backward from vertical angle. Hold the base of the TV while adjusting the angle. Description of Indicators and Controls 1. Remote sensor 2. (Power) indicator: The LED indicator lights up red in standby mode, orange in standby mode when the timer is activated, and green in the power ON mode. 3. Loudspeakers 4.
Remote Control 52R0131A_ENG.
Remote Control Install the batteries Use batteries type UM4/R03 (AAA-Size). Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such batteries. Replace exhausted batteries with new ones. Never try to recharge normal batteries - this could cause an explosion. Note: Exhausted batteries can leak corrosive electrolyte, which may cause damage to the remote control therefore remove exhausted batteries immediately. 1 Open the battery compartment.
Aerial connection Note: Before you connect other appliances: • To avoid potentially damaging your set, make sure all items are switched off and disconnected from the mains power when you make the connections. • Arrange the desired connection. • When you have finished making the connections, reconnect the mains power to the unit and switch it back on. Connect your aerial as shown below. Connections to other equipment is explained further on pages 53~57.
Auto setup Your unit has an Automatic installation which makes installation in your unit easy. When you turn on the unit for the first time, the Automatic installation routine is activated. Using this routine, you can select the on-screen language and automatically search for and store all the receivable analogue and digital (DVB) channels. The Automatic station presetting feature is for the set’s built-in tuner only. If you have a device such as a digital decoder (eg.
Quick guide for ANALOG MENU operation/Selecting the video input source/On-screen Language Selection Make sure the aerial connection and power supply are connected as per the description on previous page. Preparations: • Turn on the unit with the button on the unit. The (Power) indicator will light up in green. To change the unit to standby mode, press on the remote control. (Power) indicator will change from green to red. To turn on the unit from standby mode, press on the remote control again.
Automatic station presetting with the built-in Tuner/ Changing the order of stored channels Automatic station presetting with the built-in Tuner Perform this feature to search for and store new analogue TV programmes after the Automatic installation. (see page 10) Preparation: Make sure your antenna is connected to the aerial input (see page 9). Select ATV (see page 11). Then press MENU. Select AUTO TUNING, then press ENTER.
Manual TV station presetting If you like, you may manually tune a certain station into a selected program position, without deleting or modifying program position’s contents. Example: Store the BBC 2 into program position 2. connect aerial cable. Select program position 1 Preparation: 2. Press 2 (see page 14). OSD will indicate “2” in right upper corner. Eventually recently stored TV-channel’s name might also appear. MENU. Press ◀ or ▶ to select 2 Press tool-page (see right).
Basic Operation Channel selection With the numbered buttons. Example: • No. 2: Press 0 and within 2 seconds, press 2. • No. 29: Press 2 and within 2 seconds, press 9. Press CH or to change up or down a channel. This takes approx. 2 seconds. If the auto search only stored 5 stations, only these 5 will appear. Skipped channels will not appear (see page12). The CH LIST shows a list of all receivable programmes. They are located in channels 1 to 99. Press CH LIST to display the CH LIST.
Teletext Teletext is sent page by page. This unit is able to automatically store up to 256 pages, but they can only be accessed once they have been stored. This can take a few moments. Fastext/TOPtext The Fastext/TOPtext is teletext with a special directory. On the lower part of the screen there are four different coloured fields (red, green, yellow and blue). These fields lead directly to the pages shown within. The coloured buttons on the remote control correspond to the coloured fields.
Stereo reception with the built-in analogue tuner The built-in Tuner can detect and receive NICAM stereo broadcasts automatically. NICAM stereo sound reception: Select NICAM, then press ENTER. 1 Press ◀ or ▶ to select AUTO or OFF. Select OFF if you do not want to receive NICAM sound. NICAM AUTO BASS 25 TREBLE 25 BALANCE 0 SURROUND HDMI1 AUDIO OFF HDMI AUTO 2 Press EXIT to return to the normal screen.
Picture format The broadcaster may transmit a Wide Screen Signalling (WSS) signal which can determine the correct picture width and set it automatically when the AUTO setting is used. If you want to change this setting, you can select from the formats listed below. AUTO Press PIC SIZE repeatedly until AUTO appears. Manual format setting Pressing PIC SIZE repeatedly scrolls through the following options.
Other convenience functions You can change the default settings to convenience use. Icon Selected Items PICTURE PREFERENCE Setup hint SPORTS Bright and dynamic picture (factory-set) STANDARD Standard picture quality (factory-set) MOVIE Movie-like picture setting (factory-set) MEMORY Your personal preferences BRIGHTNESS / CONTRAST / COLOUR / You can adjust the picture to your preference. TINT(NTSC) / SHARPNESS The “TINT(NTSC)” option can be selected if an NTSC 3.58MHz or NTSC 4.
Guide to using the Digital Menu system When the set is in the digital mode, you can access the main menu by pressing DIGTAL MENU on the remote control. This main menu contains several options, - Language Setup - Channel Organizer - Installation - System Configuration - Technical Information - Common Interface The main menu is the gateway for all the other ‘sub’ menus. You can navigate between the different options in the main menu by pressing ◀ or ▶.
Language Setup/Auto Scan Language Setup Preparation: Switch on appliance. Press TV/DVD to select the TV mode, then press ATV/DTV. The appliance switches over to DVB-T-mode. Menu languages supported are English, French, German, Italian, Spanish, Russian, Portuguese, Dutch, Polish, Swedish, Turkish, Finnish, Greek, Danish and Norwegian. (Welsh and Gaelic are available only for Digital Service Language.) DIGITAL MENU, the menu will appear on the screen.
Manual Scan/ Carrier Setup Manual Scan With the Manual Scan option, you can tune one carrier at a time, by entering the carrier parameters manually. 1 Press ▲ or ▼ to select ‘Manual Scan’, then press ENTER. Main menu Installation 1 Texd CH ABC i 2 CH 3 CH CI Auto Scan Manual Scan can choose the carrier number from the Channel list by 2 You using ◀ or ▶ and the corresponding frequency set for the Carrier Setup carrier will be set for tuning.
Channel Organizer The Channel Organizer feature provides options to organise the channels. The following options are supported: Lock, Skip, Go To, Delete, Rename, Move, Change No., Move To. ◀ or ▶ to select ‘Channel Organizer’, then press 1 Press ENTER. Main menu Channel Organizer 1 Texd CH ABC i 2 CH 3 CH CI Channel Organizer Channel Organizer menu will appear. The available 2 The programmes will be listed, depending on the current mode. The selected programme will be highlighted.
Channel Organizer Setting details Rename Move Change No. * Move To * • Delete • Go To • • Skip • • Lock When the service is locked, you must enter your PIN whenever you tune to the service. ① Press ▲/▼ to select the desired service. ② Press 1 on the remote control. If you already set the PIN, enter it here. If not, enter the factory preset PIN “0000”. An icon displays indicating the service is locked. Pressing 1 will turn the lock icon on and off. (PIN entry is required.
Display Setup/Time Setup Display Setup 1 Press ▲ or ▼ to select ‘Display Setup’, then press ENTER. Main menu System Configuration 1 Texd CH ABC i 2 CH 3 CH CI Display Setup Time Setup Password Setup Subtitle Setup menu will appear. 2 Display Press ▲ or ▼ to select the item you want to change. Then you can change each setting by pressing ◀ or ▶. Banner timeout 1 sec, 2 sec.…. 7 sec. Banner position Top Select how long the service banner information appears on screen.
Password Setup (Parental lock) Password Setup (Parental lock) This feature allows you to have a parental control of the service viewing as per your preference. Once a service is protected with a password, it cannot be viewed unless the correct password is provided. ▲ or ▼ to select ‘Password Setup’, then press 1 Press ENTER.
Version/Software Upgrade/Common Interface Version You can check the software and hardware versions. ▲ or ▼ to 1 Press select ‘Version’, then press ENTER. The hardware and software versions are displayed. Main menu Technical Information 1 Texd CH ABC i 2 CH 3 CH CI Version Software upgrade 2 Press EXIT to return to the normal screen. Software Upgrade Software Upgrade allows you to download the latest software available on the Engineering channel.
Channel list/Channel banner Channel list 1 Press CH LIST to display the Channel list menu. Channel list List of the services 2 TV S.No Services 671 672 673 674 679 800 MNO PQR STU TCM VWXYZ SAT.1 Navigate Enter Exit TV/Radio Select the Services: List of the services present under the selected Channel group will be displayed in the left side of the menu. Press ▲ or ▼ to toggle within the service list, then press ENTER.
Multi audio/DVB-Subtitle/Using the Digital Service (UK only) Multi audio You can select your preferred Audio mode and DVB (digital TV) subtitle Language. The Multi audio menu will display the Audio mode and Language options available with the current broadcast. Press AUDIO SELECT to display the Multi audio menu. The Audio mode and Language code will be displayed if available. 1 Multi audio Audio mode No. Language Code 001 ENG Stereo select Audio mode, press ◀ or ▶.
EPG (Electronic Program Guide) The Guide menu shows the available programme listings for the next 8 days only, including today. However, the guide menu will show ‘No Event Name’ for programmes which are more than 8 days ahead, or for programmes within the 8 days when no programme information is available. 1 Press GUIDE to display the Guide menu. Guide 16:50 Sun 20/08/2008 671 MNO TV Sun 20/08/2008 671_MNO_10Step_0820_0100_0120_Audio2_0100_0120...
EPG Timer You can choose whether or not the screen switches on when the timer event begins - please see page 18 (Rec screen status (LCD Power on/off)). This is so that if you are using the timer to make a recording to your VCR or other device, the TV screen will not switch on unless you want it to. If you try to switch to another channel while a timer event is in progress, the following message will appear: ‘WARNING: CHANGING THE CHANNEL WILL INTERRUPT YOUR EVENT TIMER.
Disc DVD discs must be Region 2 or Region ALL type to play on this unit. The suitable disc formats are: DVD-Video, DVD-R/-RW (Video format only), Audio CD, CD-R/CD-RW and Video CD. Some CD-R/RW discs may be incompatible. • This unit can play an 8cm disc. Please do not use a disc adapter. It may cause trouble. • Please do not insert any disc of an irregular shape into the unit, as it may interfere with the function of the unit. You may not be able to remove it.
Playing a disc This section shows you the basics on how to play a disc. Basic playback (DVD/VCD/Audio CD) Preparation Press on the unit. TV/DVD on the remote control to select the DVD 1 Press mode. the disc in the 2 Place disc slot with the label side facing forward. (If the disc has a label.) • Do not place a disc which is unplayable in this unit. the TV-screen, “ ” changes to “Reading” and then 3 On playback commences. • A menu screen will appear on the TV screen if the disc has a menu feature.
Playing a disc To pause playback (still mode) Press during playback. To resume normal playback, press PLAY ( ). • The sound is muted during still mode. To stop playback Press . To remove the disc Press . Remove the disc after the disc comes out. Note: • If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen according to the type of loaded disc. In this case, check your disc again (see pages 31 and 50).
Playing a disc You can play discs at various speeds. Playing in fast reverse or fast forward directions (DVD/ VCD/Audio CD) Press or during playback. : Fast reverse playback : Fast forward playback Each time you press or , the playback speed changes. To resume normal playback Press PLAY ( ). Note: • The unit mutes sound during reverse and forward scan of DVD/VCD discs. • The playback speed may differ depending on the disc. • You can use fast reverse/fast forward playback for mp3/DivX® CD.
Zooming/Locating desired scene Zooming (DVD/VCD) This unit will allow you to zoom in the frame image. You can then make selections by switching the position of the frame. 1 Press ZOOM during playback. 1 The centre part of the image will be zoomed in. Each press of ZOOM will change the ZOOM 1(x 1.3), (x 1.5) and 3 (x 2.0). 2 Press ▲/▼/◀/▶ to view a different part of the frame. 2 You may move the frame from the centre position to UP, DOWN, LEFT or RIGHT direction.
Marking desired scenes Marking the scenes (DVD/VCD/Audio CD) The unit stores the points that you want to watch again up to 3 points. You can resume playback from each scene. MARKER during 1 Press playback. the blank Marker using 2 Select ▲ or ▼. Then press ENTER at the desired scene. Marker 1 Marker 2 Marker 3 Marker 1 Marker 2 Marker 3 00 27 54 • Repeat this procedure to set the other 2 scenes. 3 Press MARKER to clear this display.
Repeat playback/A-B Repeat playback Repeat playback (DVD/VCD) 1 2 Press PLAY MODE during playback or stop mode. Press ENTER repeatedly to select “Chapter” or “Title”. Play Mode Repeat : Off The unit automatically starts repeat playback after finishing the current title or chapter. 3 [Video CD] Press ▼ to select “Repeat”. Press ENTER to select “Track” or “All”. • If you set the repeat mode during stop mode, press PLAY ( ) to start Repeat playback. Press PLAY MODE again to clear the screen.
Changing angles/Title selection/DVD menu Changing angles (DVD) When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from. ANGLE during 1 Press playback. 1/2 The current angle will appear. ANGLE repeatedly until the desired angle is 2 Press selected. Note: • Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD. Title selection (DVD) Two or more titles are recorded on some discs.
Changing soundtrack language/Subtitles/Disc status Changing Soundtrack Language (DVD/VCD) You can select the language when you play a multilingual disc. AUDIO SELECT during 1 Press playback. 1/2 Eng Dolby Digital The current soundtrack language will appear. AUDIO SELECT repeatedly 2 Press until the desired language is 2/2 Fre Dolby Digital selected. • The on screen display will disappear after a few seconds. In case of Video CD playback Audio type changes as follows each time you press AUDIO SELECT.
MP3/JPEG/DivX® and Audio CD operation This unit can playback the MP3/JPEG/DivX®-data which has been recorded on CD-R/RW. Audio CD also can be played back. To produce the MP3/JPEG/DivX®-data, you need a Windows-PC with CD-RW drive and a MP3/JPEG/DivX®-encoding Software (not supplied). The Apple-HFS-System cannot be played. This unit requires discs/recordings to meet certain technical standards in order to achieve optimal playback quality.
MP3/JPEG/DivX® and Audio CD operation Loading CD 1 Load a MP3/JPEG/DivX CD or an Audio CD into the disc slot. browser screen will appear on the screen. 2 A• file In case the current directory includes 9 files or more, ® press ▲ or ▼ to scroll in the file list. • To see contents in folder, select the folder and then press ENTER. To return to the parent directory, select “ Go Up ...” then press ENTER.
MP3/JPEG/Divx® and Audio CD operation JPEG playback 1 Infile.the file browser, press ▲/▼ to select the desired JPEG To display a thumbnail list, press DVD MENU. Press ▲/▼/◀/▶ to select the desired file. (To return to the file browser, press TOP MENU.) When PLAY ( ) is pressed after displaying the file browser, playback begins automatically starting from the first file. In this case, if the first file is a JPEG file, the first JPEG file is played back. /Picture-01.
MP3/JPEG/Divx® and Audio CD operation DivX® playback browser, press 1 In▲/▼thetofileselect the desired file. /Movie-01.DIVX Select Files Movie-01 Movie-02 Repeat :Off When PLAY ( ) has been pressed after the file browser displayed, playback begins JPEG Preview automatically starting from the Movie-08 first file. In this case, if the first file is a JPEG file, the first JPEG file is played back. If the first file is a DivX® file, the first DivX® file is played back.
MP3/JPEG/DivX® and Audio CD operation Repeat playback (Audio CD/MP3/JPEG/DivX®) file browser, press ▲/▼/◀/▶ 1 toIn the select “Repeat” during stop mode. ENTER repeatedly to select 2 Press “Track” or “All”. Folder-1 Select Files Folder-2 Repeat :Off MP3-1 Mode :Off Folder-1 Folder-2 MP3-1 Select Files Repeat :Track Mode :Off PLAY ( ). 3 Press The unit automatically starts repeat playback after finishing the current track. To resume normal playback Select Repeat : “Off” in step 2.
MP3/JPEG/DivX® and Audio CD operation Program playback (Audio CD/MP3/JPEG/DivX®) file browser, press▲/▼/◀/▶ 1 toIn the select “Edit Mode”, then press Folder-1 Folder-2 MP3-1 MP3 2 ENTER. When “Edit Mode” is black color, you can mark the files which you want to add into Program list. Press ▲/▼/◀/▶ to select the file 2 you want to add into the program Repeat :Off Mode :Off Edit Mode MP3-1.MP3 Folder-1 list. Folder-2 MP3-1 Repeat :Off Mode :Off Edit Mode Press ENTER.
Program playback/Random playback You can arrange the playback order of tracks or files on the disc. And the unit can also select tracks or files at random and playback them. These feature works for Video CD. For Audio CD and MP3/JPEG/DivX® CD, please see “Random playback (Audio CD/MP3/JPEG/DivX®)” on page 44 and “Program playback (Audio CD/MP3/JPEG/DivX®)” on page 45. Program playback (VCD) PLAY MODE during 1 Press stop mode.
Customizing The Function Settings You can change the default settings to customize performance to your preference. Setting procedure 1 Press SETUP in stop mode. The following on-screen display appears. ▲ or ▼ to select the desired 2 Press section, then press ▶ or ENTER. Parental DRC E.B.L.
Customizing The Function Settings Menu, Subtitle, Audio You can select the language of “Menu”, “Subtitle” and “Audio” if more than one language is recorded onto the disc. English, Francais, Espanol, Deutsch, Italiano: The selected language will be heard or seen. Parental DRC E.B.L.
Customizing The Function Settings Picture Mode There are two types of source content in pictures recorded in DVD video discs: film content (pictures recorded from films at 24 frames per second) and video content (video signals recorded at 30 frames per second). Make this selection according to the type of content being viewed. Auto: Select this selection normally. The DVD player automatically detects source content, film or video of playback source, and converts that signal in an appropriate method.
Customizing The Function Settings Parental DRC E.B.L. Menu Parental : Off English QSound TV Subtitle Password Screen : 4:3 On English Change DivX(R) Display VOD Audio Display : On English Picture Mode OSD : English Auto JPEG Interval : 5 Seconds Screen Saver : On Some discs are specified as not suitable for children. Such discs can be limited not to playback with the unit. 1) Press ▲ or ▼ to select “Parental”, then press ENTER. “Enter Password” screen will appear.
Temporary cancel the rating level by DVD disc Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set. It is up to you to decide whether to cancel the rating level or not. 1 Load a DVD disc. the DVD disc has been designed to temporarily cancel the 2 IfRating level, the screen which follows the “Reading” screen will change, depending on which disc is played. If you select “YES” with the ENTER, password input screen will then appear.
Language Code List Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” (see pages 48).
PC connection As PCs are sometimes supplied with a ‘conventional’ CRT monitor, you may need to adjust the display settings of your PC’s graphics card, otherwise the pictures may not appear correctly. Switch on your PC (still with your original monitor) - select ‘1360 x 768’ for the screen resolution, and select 60 Hz for the on-screen refresh rate. Switch off your PC, then connect it to your LCD TV while both items are still switched off. Monitor Display modes MODE V. Frequency H.
Connecting an HDMI or a DVI device to the HDMI input The HDMI (HDMI1)input receives digital audio and uncompressed video from a HDMI equipped device or uncompressed digital video from a DVI equipped device. When you connect the HDMI (HDMI1) to a DVI device with a HDMI-to-DVI adapter cable, it only transfers the video signal, so it is necessary to use separate analogue leads to transfer the audio signals. Select the HDMI input mode (see page11).
Connection to other equipment 1. Connecting other units to your TV Caution. Before connecting: • Make sure to disconnect the appliance from the power supply in order to avoid any potential damage from occurring. • Make sure to establish the required connection. • Make sure that connections are properly and correctly attached before connecting the appliances to the power supply. Connect with Satellite receiver as shown below. Select the TV-Program at the satellite receiver.
Connection to other equipment 3. Connecting an audio system You can supply the TV sound to the stereo equipment (A) with the scart socket. Use a special scart cable for the connection sold separately. (please consult your hi-fi instructions for details). If you have a surround sound amplifier/decoder (B) with a coaxial digital input, you can connect the Coaxial Digital Audio Output to it, using a suitable coaxial digital lead. This connection carries the audio signal from the set’s Digital channels only.
Connection to other equipment 5. Connecting to a DVD player or other AV device with Component Video outputs If your DVD player (or other device) has Component Video output jacks, use a suitable set of leads (RCA/ Phono) to connect these to the Component Video inputs on this TV as shown - it can greatly enhance the picture quality and performance. Please remember that you will also need to connect separate leads (RCA/Phono) for the audio signals. Select the COMPONENT input mode (see page 11).
Troubleshooting table Please check the following list before requesting service. Symptom TV No picture, no sound No reception The TV switches off with missing antenna input signal menu, the TUNING In option cannot be selected. Wrong Colours Possible solution Switch on the set. Check that the mains power outlet is properly connected. Select appropriate input mode. Unplug unit for 1 minute, then plug it back in. Have you tuned in the TV stations? Connect the antenna.
Specifications Model 19DV615DG/ 19DV616DG 22DV615DG/ 22DV616DG 26DV615DG TV System: Analogue: PAL UK, IR, CCIR, FRENCH System, B/G, D/K, I/I, L Digital: DVB-T (OFDM 2k/8k 16QAM/64QAM) Video Colour System: PAL/SECAM/NTSC 3.58/NTSC 4.
EU Conformity Statement “This product is marked with “CE” and complies therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC.” Responsible for CE-marking is TOSHIBA INFORMATION SYSTEMS (U.K.