LCD TV/DVD COMBINATION 19DV665DB 19DV667DB 22DV665DB 22DV667DB 26DV665DB OWNER’S MANUAL Owner’s Record The model number and serial number are on the back of your TV/DVD. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV/DVD. ©2009 Toshiba Corporation Before operating the unit, please read this manual thoroughly.
Precautions CAUTION: THIS UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE UNIT. CLASS 1 LASER PRODUCT WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
Contents Precautions ................................................................................................................................................................................ 2 Important safety information ........................................................................................................................................................ 4 Location of controls ...........................................................................................................
Important safety information This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use. • Although this appliance has been carefully manufactured and rigorously checked prior to leaving the factory, as with all electrical appliances it is possible for problems to develop.
Important safety information (continued) Where to install Locate the television away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen. Place on a sturdy platform, the mounting surface should be flat and steady.
Location of controls 4 Disc slot 5 6 C.I. slot 7 8 9 10 1 2 3 Adjusting the screen angle You can adjust the angle of the TV-screen for 2º forward or for 10º backward from vertical angle. Hold the base of the TV while adjusting the angle. Applicable to the following models: 19DV665DB, 19DV667DB, 22DV665DB, 22DV667DB Description of indicators and controls 1. Remote sensor 2.
Remote control Function Page Eject a disc 35 Select to operate TV/DVD 11, 34 Switches between the analogue TV and the digital TV 11 Enter standby mode or turn on the power 10 Select channel Select Teletext page Enter password Display source information 17 19 25, 55 18, 32 Turn the sound on/off 17 Toggle between TV, Radio, and Data mode 17 Select an input source 13 Change the TV channel or Teletext page up or down In Standby: Turn on the power 17, 19 11 Volume 17 Select menu of a DVD di
Remote control (continued) Install the batteries Use batteries type UM4/R03 (AAA-Size). Notes: • Exhausted batteries can leak corrosive electrolyte, which may cause damage to the remote control - therefore remove exhausted batteries immediately. • Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such batteries. Replace exhausted batteries with new ones. Never try to recharge normal batteries - this could cause an explosion.
Aerial connection Note: Before you connect other appliances: • To avoid potentially damaging your set, make sure all items are switched off and disconnected from the mains power when you make the connections. • Arrange the desired connection. • When you have finished making the connections, reconnect the mains power to the unit and switch it back on. Connect your aerial as shown below. Connections to other equipment is explained further on pages 56 ~ 59.
Auto setup Your unit has an Automatic installation routine which makes installation in your unit easy. When you turn on the unit for the first time, the Automatic installation routine is activated. Using this routine, you can select the on-screen language, and automatically search for and store all the receivable analogue and digital (DVB) channels. The Automatic station presetting feature is for the set’s built-in tuner only. If you have a device such as a digital decoder (e.g.
Quick guide for menu operation Make sure the aerial Quick guide for menu operation connection and power supply Launch the Main Menu screen. For example: Select Auto Tuning. are connected as per the description on page 9. Press INPUT . 1 Preparations: • Turn on the unit with the button on the unit. The power indicator will light up in green. To change the unit to standby mode, press on the remote control. Power indicator will change from green to red.
Quick guide for menu operation (continued) The Auto Scan process will now begin. A progress bar appears to indicate scanning progress. Note: • ...on the following pages the Main Menu screen can be called in the same way as here.
Selecting the video input source Selecting the video input source 1 Press INPUT to view a signal from another device connected to your TV, such as a VCR or DVD player. You can select each input source depending on the input jack used to connect your devices. 2 Press / or the corresponding number on the screen to select a video input source, then press ENTER/CH LIST within 5 seconds.
Automatic station presetting with the built-in Tuner Automatic station presetting with the built-in Tuner Perform this feature to search for and store new analogue and digital TV programmes after the Automatic installation (see page 10). Preparation: Make sure your antenna is connected to the aerial input (see page 9). Select ATV or DTV (see page 11), then press MENU SETUP / or DIGITAL MENU 1 2 3 Press 4 Select “Start”, then press ENTER/CH LIST .
Changing the order of stored channels Changing the order of stored channels The Automatic station presetting stores the stations in a specific order. However, this order can be changed if you wish. Note: • When changing the order of the channels, it is best to start with Ch1. 1 Press / to select “Ch Allocation”, then press ENTER/CH LIST . 2 Select the desired option, then press ENTER/CH LIST . 3 After setting each option, press MENU SETUP to return to Ch Allocation menu. 4 Press EXIT/CANCEL screen.
Manual TV station presetting If you like, you may manually tune a certain station into a selected programme position, without deleting or modifying program position’s contents. The presetting applies to both analogue and digital TV. Press the ATV/DTV button to enter ATV or DTV mode then follow the steps to set the TV stations manually. Preparation: Connect the aerial cable. Select programme position “2”. Press 2, OSD will indicate ‘2’ in left upper corner.
Basic operation Channel selection Use the 0 - 9 numbered buttons. Example: • No. 2: Press 0 and within 2 seconds, press 2. • No. 29: Press 2 and within 2 seconds, press 9. (1) Press CH / to select a channel. This takes approx. 2 seconds. If the auto search only stored 5 stations, only these 5 will appear. Skipped channels will not appear (see page 15). The Channel List shows a list of all receivable programmes. They are located in channels 1 to 99 for ATV mode and 1 to 999 for DTV mode.
Basic operation (continued) Information display In ATV mode: Press to display the Channel number and sleep timer settings information on the screen. Current settings for the sound mode, picture size, and resolution (if in use) are also displayed. The information will appear for approx. 5 seconds. In DTV mode: When you switch channels, a channel banner is displayed for a few seconds.
Teletext Teletext is sent page by page. This unit is able to automatically store up to 256 pages, but they can only be accessed once they have been stored. This can take a few moments. Fastext/TOPtext Hold Pages The Fastext/TOPtext is teletext with a special directory. On the lower part of the screen there are four different coloured fields (red, green, yellow, and blue). These fields lead directly to the pages shown within. The coloured buttons on the remote control correspond to the coloured fields.
Stereo reception with the built-in analogue tuner The built-in tuner can detect and receive NICAM stereo broadcasts automatically. NICAM stereo sound reception 1 Press MENU SETUP to display the Main Menu screen. Press / to select “Sound“, then press ENTER/CH LIST . 2 Select “NICAM”, then press / to select “Auto” or “Off”. Select “Off” if you do not want to receive NICAM sound. 3 Press EXIT/CANCEL to return to the normal screen.
Picture format The broadcaster may transmit a Wide Screen Signaling (WSS) signal which can determine the correct picture width and set it automatically when the ‘Auto’ setting is used. If you want to change this setting, you can select from the formats listed below. Auto picture size Press PIC SIZE repeatedly until ‘Auto’ appears on-screen. Picture format setting Press PIC SIZE repeatedly to scroll through the following options.
Other convenience functions You can change the default settings to convenience use. Main menu Picture Selected items Picture Setting Brightness/ Contrast/ Sharpness/ Colour/ Tint Setup hint You can adjust the picture to your preference. The ‘Tint’ option can be selected if an NTSC 3.58 MHz or NTSC 4.43 MHz signal is input through one of the AV inputs, and NTSC or Auto has been selected for the AV Colour option.
Other convenience functions (continued) You can change the default settings to convenience use. Main menu Setup Selected items Language Setup Audio Description Setup hint Menu Language Select a display language. Pref. Audio Language Select an audio language (DTV mode only). Pref. Subtitle Language Select a subtitle language (DTV mode only). Pref. Digital Service Language Select a digital service language (DTV mode only).
Display setup/Timer setting (DTV mode only) Display Setup 1 2 3 Press DIGITAL MENU or MENU SETUP to display the Main Menu screen. Press / to select “Setup” menu, then press ENTER/CH LIST Press / to select “Display Setup”, then press ENTER/CH LIST . . The Display Setup menu appears. 4 5 Press / to select an item, then press / to change each setting. Banner Timeout 1 sec, 2 sec... 7 sec. Select how long the service banner information appears on the screen.
Password setup (Parental lock) (DTV mode only) Password Setup (Parental lock) This feature allows you to have a parental control of the service viewing as per your preference. Once a service is protected with a password, it cannot be viewed unless the correct password is provided. 1 2 Press DIGITAL MENU or MENU SETUP to display the Main Menu screen. Press / to select the “Setup” menu, then press ENTER/CH LIST . Press / to select “Password Setup”, then press ENTER/CH LIST .
Version Version You can check the software version information. 1 2 3 Press DIGITAL MENU or MENU SETUP to display the Main Menu screen. Press / to select the “Setup” menu, then press ENTER/CH LIST Press / to select the “Version” menu, then press ENTER/CH LIST . Note: • Version check also applies to ATV mode. The software version is displayed. 4 26 Press EXIT/CANCEL to return to the normal screen. .
Software upgrade (DTV mode only) Software Upgrade Software Upgrade allows you to download the latest software available on the channel. 1 2 3 Press DIGITAL MENU Press / or MENU SETUP to display the Main Menu screen. to select the “Setup” menu, then press ENTER/CH LIST . Press / to select “Software Upgrade”, then press ENTER/CH LIST to select “Start” to check if the TV has the Over Air Download service.
Common interface (DTV mode only) Common Interface You can access the Common Interface module information from this menu option. Preparations: Insert CAM into the DVB Common Interface (C.I.) slot on the backside of the TV (see page 9). 28 1 2 3 Press DIGITAL MENU 4 The conditional access module (CAM) name is displayed. Press ENTER/CH LIST to view more information. 5 On the CI menu, options relating to the CAM module is displayed on the screen.
Multi audio (DTV mode only) Multi audio You can select your preferred Audio mode and DVB (Digital Video Broadcasting) subtitle language. The Multi audio menu will display the Audio mode and Language options available with the current broadcast. 1 Press AUDIO SELECT to display the Multi audio menu. The Audio mode and Language code will be displayed, if available. 2 Press / to select Audio mode. The Audio mode options include: Stereo, Left, Right, and L + R.
DVB-Subtitle/Using the Digital Service (DTV mode only) DVB-Subtitle DVB-Subtitle is a feature supported in DVB (Digital Video Broadcasting) applications in which the service shown can be accompanied by a text display on the screen in parallel with the corresponding audio service. The DVB-Subtitle feature can be enabled or disabled at anytime. 1 Press SUBTITLE menu. 2 3 Press 4 Press EXIT/CANCEL / to display the Subtitle to select your desired subtitle language from the available languages.
EPG (Electronic Program Guide) (DTV mode only) The Guide menu shows the available programme listings for the next 8 days only, including today. However, the guide menu will show ‘No Event Name’ for programmes which are more than 8 days ahead, or for programmes within the 8 days when no programme information is available. 1 Press GUIDE 2 Press TV/RADIO to switch from three service modes; TV, Radio, and Data, to view the EPG data accordingly.
EPG Timer (DTV mode only) You can choose whether or not the screen switches on when the timer event begins - see page 23 (Rec screen status (LCD Power on/off)). This is so that if you are using the timer to make a recording to your VCR or other device, the TV screen will not switch on unless you want it to. If you try to switch to another channel while a timer event is in progress, the following message will appear: ‘Warning: Changing the channel will interrupt your event timer.
Disc DVD discs must be Region 2 or Region ALL type to play on this unit. The suitable disc formats are: DVD-Video, DVD-R/-RW (Video format only), Audio CD, CD-R/CD-RW, and Video CD. Some CD-R/RW discs may be incompatible. • This unit can play an 8cm disc. Please do not use a disc adapter. It may cause trouble. • Please do not insert any disc of an irregular shape into the unit, as it may interfere with the function of the unit. You may not be able to remove it.
Playing a disc This section shows you how to play a disc. Basic playback (DVD/VCD/Audio CD) Preparation: 1 2 Press 3 Load the disc in the disc slot with the label side facing forward. (If the disc has a label.) on the unit. Press TV/DVD on the remote control to select the DVD mode. The DVD startup screen appears on-screen. Note: • Do not place a disc which is unplayable in this unit. Notes: • If the unit does not operate properly: Static electricity, etc., may affect the player’s operation.
Playing a disc (continued) To start playback in stop mode Press PLAY . To pause playback (still mode) Press PAUSE during playback. To continue playback from still mode Press PLAY . To stop playback Press STOP . To remove the disc 1 2 Press EJECT . Wait for the disc drive to eject the disc, then remove the disc from the slot.
Playing a disc (continued) You can play discs at various speeds. Playing in fast reverse or fast forward direction (DVD/VCD/Audio CD) 1 Press REV /FF during playback. • REV : Fast reverse playback • FF : Fast forward playback Each time you press REV /FF , the playback speed changes. 2 To resume normal playback, press PLAY . Notes: • The sound is muted during reverse and forward scan of DVD/VCD discs. • The playback speed may differ depending on the disc.
Zooming/Locating desired scene Zooming (DVD/VCD) This unit will allow you to zoom in the frame image. You can then make selections by switching the position of the frame. 1 Press CH RTN ZOOM during playback. The view will zoom into the centre of the image. 1 Each press of the button will increase the scale value: 1(x 1.3), 2 (x 1.5), and 3 (x 2.0). 2 3 Press / / / to pan the scene and view different sections of the picture. To return to normal view, in zoom mode, press CH RTN ZOOM ‘ Off’ appears.
Marking desired scenes Marking the scenes (DVD/VCD/Audio CD) Scene bookmarks refers to specific points in the playback range that has been marked for later access. You can create up to three markers per disc. 1 2 Notes: • Some discs may not work with the marking operation. • The saved scene bookmarks are only accessible during the current session. Once you eject the disc or turned off the TV/DVD, all bookmarks will be cleared. • In some cases, subtitles for the marked scene may not appear.
Repeat playback/A-B playback Repeat playback (DVD/VCD) 1 2 Press PLAY MODE during playback or stop mode. DVD Press ENTER/CH LIST “Chapter” or “Title”. [DVD] repeatedly to select Video CD Play Mode Repeat : Title [Video CD] Press / to select “Repeat”, then press ENTER/CH LIST repeatedly to select a repeat mode. Playback automatically applies after the current track is finished.
Changing angles/Title selection/DVD menu Changing angles (DVD) When playing back a disc recorded with multi-angle scenes, you can select the scene angle that you prefer. 1 Press ANGLE during playback. The current angle will appear. 2 Press ANGLE 1/2 repeatedly until the desired angle is displayed. Note: • Depending on the DVD, you may not be able to change the scene angle even if multi-angle data are recorded on the DVD. Title selection (DVD) Some DVDs contain two or more titles.
Changing soundtrack language/Subtitles/Disc status Changing soundtrack language (DVD/VCD) You can select the soundtrack language when you play a multilingual disc. 1 Press AUDIO SELECT during playback. The current soundtrack language will appear. 2 Press AUDIO SELECT repeatedly until the desired language is selected. The on-screen display will disappear after a few seconds. 2/2 D 5.1 Ch Eng In case of Video CD playback Audio type changes are as follows each time you press AUDIO SELECT Stereo .
MP3/JPEG/DivX® and Audio CD operation This unit can playback the MP3/JPEG/DivX®-data which has been recorded on CD-R/RW. Audio CD also can be played back. To produce the MP3/JPEG/DivX®-data, you need a Windows-PC with CD-RW drive and a MP3/JPEG/DivX®-encoding Software (not supplied). The Apple-HFS-System cannot be played. This unit requires discs/recordings to meet certain technical standards in order to achieve optimal playback quality.
MP3/JPEG/DivX® and Audio CD operation (continued) Loading CD 1 2 Load a MP3/JPEG/DivX® CD or an Audio CD into the disc slot. A file browser screen will appear on the screen. • If the current directory has more than 8 files, press / to scroll the file list. • To see folder contents, select a folder and then press ENTER/CH LIST . To return to the root directory, select “ Go Up ...” then press ENTER/CH LIST .
MP3/JPEG/DivX® and Audio CD operation (continued) JPEG playback 1 In the file browser screen, press / to select an image file for viewing. A preview of the selected file displayed in the Preview panel. To display a thumbnail list, press DVD MENU Press / / / to select the image file. /Picture-01.JPG . (To return to the file browser, press TOP MENU Picture-01 Select Files Picture-02 Repeat :Off Picture-03 Mode :Normal Picture-04 Picture-05 Picture-06 .
MP3/JPEG/DivX® and Audio CD operation (continued) DivX® playback 1 In the file browser screen, press / to select the desired file. When PLAY is pressed without selecting the file, playback starts automatically from the first file in the list. /Movie-01.DIVX Movie-01 Select Files Movie-02 Repeat :Off Movie-03 Mode :Normal Movie-04 Movie-05 Movie-06 Movie-07 JPEG Preview Movie-08 2 Press ENTER/CH LIST playback.
MP3/JPEG/DivX® and Audio CD operation (continued) Repeat playback (Audio CD/MP3/JPEG/DivX®) 1 2 In the file browser screen, press Press / to move the selection highlight to the Option panel. to select “Repeat”. Select Files Folder-1 3 Press ENTER/CH LIST mode, “Track” or “All”. Folder-2 Repeat :Off MP3-1 Mode :Normal repeatedly to select a repeat Select Files Folder-1 Notes: • The repeat or random function is cancelled when you eject the disc or turn the power off.
MP3/JPEG/DivX® and Audio CD operation (continued) Programme playback (Audio CD/MP3/JPEG/DivX®) 1 2 In the file browser screen, press to move the selection highlight to the Option panel. Press / to select “Edit Mode”, then press ENTER/CH LIST to enable it. Folder-1 Folder-2 Repeat :Off Mode :Normal MP3-1 MP3 2 3 Press to move the selection highlight to the file list, then press / to select a file. Press ENTER/CH LIST to mark it for inclusion in the programme playlist.
Program playback/Random playback You can arrange the playback order of tracks or files on the disc. And the unit can also select tracks or files at random and playback them. These features work for Video CD. For Audio CD and MP3/JPEG/DivX® CD, please see “Random playback (Audio CD/MP3/ JPEG/DivX®)” on page 46 and “Programme playback (Audio CD/MP3/JPEG/ DivX®)” on page 47. Program playback (VCD) 1 Press PLAY MODE during stop mode.
Customizing the function settings You can change the default settings to customize performance to your preference. Setting procedure 1 In DVD mode, press MENU SETUP in stop mode. Parental DRC E.B.L. Menu : Off :English Subtitle :English QSound TV Screen Set Password : 4:3 On DivX Subtitle Output Display :ASCII : Interlace On Audio :English Picture Mode DivX(R) :VOD Auto OSD JPEG Interval Screen Saver 2 Press / to select a setup tab, then press :English :5 Seconds : On .
Customizing the function settings (continued) Settings details Section Option Details Page Menu Select the language for the DVD menu display. 51 Subtitle Select the subtitle language for disc playback. DivX Subtitle Select the subtitle encoding format for DivX® VOD playback. Audio Select the audio language for disc playback. OSD Select a preferred language for on-screen display. TV Screen Select a picture size according to the aspect ratio of your TV.
Customizing the function settings (continued) Menu and OSD Select the language for the DVD and Setup menu display. Options include: English, French, Spanish, German, Italian Subtitle and Audio Parental DRC E.B.L.
Customizing the function settings (continued) JPEG Interval You can continuously playback all JPEG files automatically. After the selection below, the disc will start playback on JPEG files which have been recorded. • Off: Plays back one file at a time. • 5 seconds: Plays back images in the form of a slide show at 5 second intervals. • 10 seconds: Plays back images in the form of a slide show at 10 second intervals. • 15 seconds: Plays back images in the form of a slide show in 15 second intervals.
Customizing the function settings (continued) Parental Some discs are specified as not suitable for children. Such discs can be limited not to playback with the unit. (1) Press . / to select “Parental”, then press ENTER/CH LIST “Enter Password” screen will appear. (2) Press “0000” using Number buttons (0 – 9). (Please note, this is presetting DRC Menu E.B.L.
Customizing the function settings (continued) Password (1) Press . / to select “Password”, then press ENTER/CH LIST The ‘Enter Current Password’ screen will appear. (2) Press Number buttons (0 – 9) to input the current password (If the password has not been set yet after you purchase this unit, it is “0000”), then press ENTER/CH LIST . (3) Press ENTER/CH LIST again, the ‘Enter New Password’ screen will appear, then use Number buttons (0 – 9) to input the new password. (4) Press ENTER/CH LIST .
Temporary cancel the rating level by DVD disc Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set. It is up to you to decide whether to cancel the rating level or not. 1 Load a DVD disc. 2 If the DVD disc has been designed to temporarily cancel the Rating level, the screen which follows the Reading screen will change, depending on which disc is played. If you select “Yes” and ENTER, the password input screen will then appear.
PC connection As PCs are sometimes supplied with a ‘conventional’ CRT monitor, you may need to adjust the display settings of your PC’s graphics card, otherwise the pictures may not appear correctly. Switch on your PC (still with your original monitor) - select “1360 x 768” for the screen resolution, and select 60 Hz for the on-screen refresh rate. Switch off your PC, then connect it to your TV while both items are still switched off. Monitor display modes Mode Resolution V. Frequency H.
Connecting an HDMI or a DVI device to the HDMI input The HDMI (19/22 inch) or HDMI1/HDMI2 (26 inch) input receives digital audio and uncompressed video from a HDMI equipped device or uncompressed digital video from a DVI equipped device. When you connect the HDMI (19/22 inch) or HDMI1 (26 inch) to a DVI device with a HDMI-to-DVI adapter cable, it only transfers the video signal, so it is necessary to use separate analogue leads to transfer the audio signals.
Connecting TV to other equipment 1 Connecting aerials and other devices to your TV Connect the cable TV coaxial cable directly to the aerial input jack on the rear of the TV. TV (Back side view) To AV1 input To Tuner Antenna Satellite antenna SCART cable To AV3 (Video, Audio L/R) input (26-inch model) Audio/video cable Video recorder Decoder Satellite receiver DVD player (All illustrated cables are not supplied.
Connection TV to other equipment (continued) 3 Connecting a DVD player TV (Back side view) Connect a DVD player as shown. Select AV1 or AV2 input mode. DVD player (26-inch model) SCART cable (not supplied) 4 To AV2 input Connecting a video camera Select the AV3 input mode (see page 13). You can see the playback picture from the video camera.
Status message Information/Status message Cause Invalid entry The channel does not exist. (e.g., “000“) No radio services Cannot change to Radio mode because there is no radio service in the channel list. No TV services Cannot change to TV mode because there is no TV service in the channel list. No data service Cannot change to data mode because there is no data service in the channel list. No services There are no services in the received signal.
Troubleshooting table Please check the following list before requesting service. Symptom Possible solution Page Switch on the set. Check that the mains power outlet is properly connected. Select appropriate input mode. Unplug unit for 1 minute, then plug it back in. 6 9 13 No reception Have you tuned in the TV stations? Connect the antenna. Make sure the set is ON and not in Standby mode 10, 13 9 6 The TV switches off with missing antenna input signal This is normal.
Specifications Model Television LCD panel (approximate screen size, diagonal) System Analogue Digital Video colour system Preset channels: Frequency Analogue range Digital LCD Speaker Audio output power DVD Signal system Applicable disc Output Audio Digital audio Pickup CD DVD Input/Output HDMI input 19DV665DB / 19DV667DB 22DV665DB / 22DV667DB 26DV665DB 18.51 inch 21.6 inch 26.0 inch PAL UK, IR, CCIR, French System, B/G, D/K, I/I, L/L’ DVB-T (OFDM 2k/8k 16QAM/64QAM) PAL/SECAM/NTSC 3.58/NTSC 4.
The GNU General Public License (GPL) Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
NO WARRANTY (1) BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
EU Conformity Statement “This product is marked with “CE” and complies therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC.” Responsible for CE-marking is TOSHIBA INFORMATION SYSTEMS (U.K.
J52G0101A SH 09/01 N 52G0101A P69-Back.
