TOSHIBA STORAGE DEVICE DIVISION SD-R5112 DVD-R/-RW DRIVE PRODUCT SPECIFICATION MARCH 2003 REV. 1.
LIMITATION OF LIABILITY Those warranties in the express warranty separately agreed between TOSHIBA and your company are the only warranties given to the consumer and are in lieu of any other warranties, whether express or implied with regard to this component. TOSHIBA expressly and unequivocally disclaims the warranties of merchantability and fitness for a particular purpose.
DO NOT use this equipment in the system such as medical equipment which may cause personal injury or property damages resulting from malfunction of this equipment and unexpected data corruption or data error in reading operation. 4. Turn off the power for this equipment and wait more than one (1) minute before you eject the disc using the emergency eject mechanism when a disc cannot be ejected for some reasons in order to avoid the risk of damages to the disc. Notice 1.
6. As for mounting bracket to incorporate this product into an equipment, (1) When this product is incorporated into an equipment by using the mounting screw holes in the right and left side planes, the clearance between this product and the mounting bracket is too wide; (2) When this product is incorporated into an equipment by using the mounting screw hole in the bottom, the surface of the mounting bracket is contorted.
7. In the market, there are some drives or players that maintain to read CD or DVD disc, though, they may not designed to read CD-RW or DVD-RW disc. When you try to read the CD-RW or DVD-RW disc written by this product using other drives or players, please make sure that the equipment is applicable to CD-RW or DVD-RW disc. 8.
Contents 1. Introduction ---------------------------------------------------------------------------------------------------------------------- 1 2. Features -------------------------------------------------------------------------------------------------------------------------- 1 3. Specifications ------------------------------------------------------------------------------------------------------------------ 2 3.1.
.2. Current Drain ------------------------------------------------------------------------------------------------------- 22 7.2.1.Sleep ------------------------------------------------------------------------------------------------------------ 22 7.2.2. Standby ---------------------------------------------------------------------------------------------------------- 22 7.2.3. Continuous Read ------------------------------------------------------------------------------------------- 22 7.2.4.
1. Introduction This document describes TOSHIBA's SD-R5112 DVD-R/-RW Drive. 2. Features This drive reads DVD CSS (Contents Scramble Systems) Disc. This drive reads digital data stored on CD-ROM, DVD-ROM and CD audio discs. This drive read and records the digital data on DVD-R/-RW and CD-R/RW discs. This drive reads digital stored on DVD-ROM discs at maximum 12 times faster rotational speed. This drive reads digital stored on CD-ROM discs at maximum 40 times faster rotational speed.
3. Specifications 3.1.Performance (1) Applicable Write Format DVD-R DVD-RW CD-R/RW (2) Applicable Write Disc *1 DVD-R DVD-RW CD-R/RW (3) Applicable Read Disc *1 DVD CD :Disc at once, Incremental write :Disc at once, Incremental write, Restricted overwrite :Disc at once, Track at once, Session at once,Packet write :DVD-R for General (Ver.2.01) Optional Spec. Rev.1.0 :DVD-RW (Ver1.1) Optional Spec. Rev.1.
(5) Rotational Speed DVD (Single) DVD (Dual) DVD-R Ver.1.0 DVD-R Ver.2.0 DVD-RW Ver.1.1 DVD-Video (CSS-Disc) DVD-R Ver.2.0 (Write) DVD-RW Ver.1.1 (Write) DVD-RAM Ver.2.1 CD-ROM, CD-R CD-RW CD-DA Transfar CD-DA,Video-CD CD-R (Write) Hight speed CD-RW (Write) CD-RW (Write) : Approx. 7,580 rpm (5.0-12X CAV) : Approx. 5,053 rpm (3.3-8X CAV) : Approx. 3,200 rpm (2-4.8X CAV) : Approx. 2,780 rpm (2-4.8X CAV) : Approx. 2,780 rpm (2-4.8X CAV) : Approx. 2,780 rpm (2-4.8X CAV) : Approx.
(7) Access Time Average Random Access Time Average Random Seek Time Average Full Stroke Access Time DVD*2 CD*3 DVD-RAM*4 : 130 ms Typ : 110 ms Typ : 200 ms Typ DVD*5 CD*6 DVD-RAM*7 : 120 ms Typ : 105 ms Typ : 160 ms Typ DVD*8 CD*9 DVD-RAM*10 : 210 ms Typ : 180 ms Typ : 400 ms Typ (8) Spin up Time ( Focus Search Time and Disc Motor Start up Time ) DVD : 2.0 s Typ DVD-RAM : 2.0 s Typ CD : 2.
(9) Load/Eject (10) Air Flow (11) Acoustic Noise (12) Power Supply (a) Electrical Load/Eject (Eject Button) (b) Load/Eject by ATAPI command (c) Emergency Eject Not Required 40 dB (IEC 179 A weighted at 1 m) +5 V , +12 V (details in Section 7) 3.2. Environmental Conditions This drive should be used under the conditions listed below. 3.2.1.
3.2.2.Dust and Dirt unspecified 3.2.3.Vibration (1) Operating (1 Oct/min) -------------------------- no hard error ----5 to 500 Hz 2.45 m/s2 [0.25 G] (0-p) (excluding resonance point) (2) Operating (Write) (1 Oct/min) ---------------- no hard error ----5 to 500 Hz 2.45 m/s2 [0.25 G] (0-p) (excluding resonance point) (3) Non-operating (1 Oct/min) --------- no damage ----5 to 10 Hz 5 mm (p-p) 10 to 500 Hz 9.8 m/s2 [1 G] (0-p) (4) Shipping (Packaged) (1 Oct/min) ----- 3.2.4.
3.3. Installation Conditions Mount the drive within 20 ° of the horizontal positions and within 10 ° of the vertical positions 20° 20° 20° 20° a) Horizontal position 10° 10 ° 10 ° 10 ° b) Vertical position Figure 1 Installation position 3.4. Dimension and Mass ----- See Figure 2 for details ----- (1) External Dimensions (W x H x D) 146 mm x 41.5 mm x 189.5 mm (excluding bezel) (2) Mass (Weight) 1.0 kg (Net) 11.0 kg (Bulk Packaged 10pcs.) 16.0 kg (Bulk Packaged 15pcs.
+0.7 -0.4 189.5 (Unit:mm) Figure 2-1 External Dimensions 8/29 SD-R5112 Rev.1.
(Unit:mm) Figure 2-2 External Dimensions 9/29 SD-R5112 Rev.1.
3.5. Reliabilites 3.5.1. Error Rate (1) Hard Read Error Rate (Byte Error Rate) ----- Allowing 5 Retries(default) ----DVD: 10 -15 Max CD: Mode 1:10-15 Max Mode 2:10-12 Max 10 -6 Max (2) Seek Error Rate --- Allowing 5 Retries (default) 3.5.2. MTBF Assumptions: Power On Hours On/Off Cycles Number of Access Operating Duty Cycle (Read) Operating Duty Cycle (Write) 100,000 h 5,436 h/year 313 cycles/year 600,000 accesses/year 20 % of Power On Time (Reading/Seeking) 2 % of Power On Time (Writing/Seeking) 3.5.3.
Figure 3 Configuration LED Tray Open/Close Detector PUH GPIO Comparator Position Detector Feed Motor Eject Switch Loading Motor Disc Motor Power Driver RAM Int. Control Timer FV Clock Converter FG FLASH ROM Micro Processor 6379 Disc Motor Driver Power Driver Power Driver Disc EQL Feed EQL EDC CLV Controller LPP Demodulator Header detect ATIP Demodulator 22.
5.Functions 5.1. Disc Data Configurations 5.1.1. DVD-ROM Data Configurations Figure 4 shows how data is constructed in the case of dual layer/parallel track data DVD disc. The DVD spec defines the single layer, the dual layer/opposite and parallel track disc, that the DVD-ROM drive supports. For details refer to DVD Book Part 1. 1 block=1/676 s ID Data (Dual layer Parallel track path) Layer No. Information ID No. ID No.
5.1.3. CD-R / CD-RW Data Configurations Before writing CD-R / CD-RW disc contains time-code information called ATIP. ATIP is abbreviation of "Absolute Time In Pre-groove" in the wobbling groove by modulating the carrier frequency. (Address information is pre-formatted to ATIP on the CD-R / CD-RW disc and method for the guide groove to wobble by FM modulation.) Figure 6 shows the composition of ATIP.
5.2. Power ON/OFF Timing (Target) Figure 8 shows the initialization sequence Power ON or ATAPI-RST Max. 550 ms "Command" Receivable System Initialization Max. 4 s Focus Search Max. 5 s Spindle ON Learning CD:Typ. 12 s, DVD 2 Layer Typ. 8 s, Max.60 s (Single Session Disc) "Read-Command" Stand-by Acceptable "TEST UNIT READY" Command "Check Condition" Status "Good" Status Figure 8 Initialization Sequence 6.
6.2.Signal summary The physical interface consists of single ended TTL compatible receivers and drivers communicating through a 50P-connector as shown in Figure 13 and Figure 14 "Interface connector". 6.2.1. Signal Specification Figure 9 shows the Signal Specifications Receivers/Drivers Caracteristics withoutExternal pullup Resistor Type Sig.
6.2.2. Timing of Host Interface (PIO) Figure 10 shows the Host Interface Timings.
6.2.3.Timing of Host Interface (DMA Multi) Figure 11 shows the Host Interface DMA multi word Timings t0 DMARQ tL DMACK-*1 tK tD tI tJ DIOR-/DIOW-*1 tZ tE Read DD0-15 tF Write DD0-15 tG tH *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted.
6.2.4.Timing of Host Interface (Ultra DMA ) Figure 12 shows the Host Interface Ultra DMA word Timings tMLI DMARQ tUI DMACK- tCYC tCYC STOP tRP t2CYC tFS tACK tENV tACK tLI DMARDY t2CYC tZAD tRFS tZIORDY STROBE tDVS tDVH tDVS tDVH tDVS tDVH DD (15:0) Sender tDVS tDVH CRC tZAD tZIORDY STROBE tDS t D H tDS tDH tDS tDH tDS DD (15:0) Recipient tDH CRC In all timing diagrams, the low line indicator negated, and the upper line indicators asserted.
6.3. Connector Figure 13 shows the mixture connector (Interface/Power supply) Table 2 shows Interface connector pin assignment. power supply connector PIN #1 PIN #2 PIN #3 PIN #4 : 12 V : GND : GND : +5 V 13.21 21.18 56.38 #4 #1 8.6 6.8 2.7 2.54 2.54 3.4 3 (2.4) 48.25 2.54 10.09 2.54 120.3 +/-0.5 MODE SELECT HEADER INTERFACE CONNECTOR POWER SUPPLY CONNECTOR (4P ) ANALOG AUDIO CONNECTOR DIGITAL AUDIO CONNECTOR Figure 13 19/29 SD-R5112 Rev.1.
PIN NO.
6.4.
ATA Commands No OP Code 1 00h 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Command Description NOP 08h DEVICE RESET 20/21h READ SECTOR (S) 90h EXECUTE DEVICE DIAGNOSTICS A0h PACKET A1h IDENTIFY PACKET DEVICE E0h STANDBY IMMEDIATE E1h IDLE IMMEDIATE E2h STANDBY E3h IDLE E5h CHECK POWER MODE E6h SLEEP E7h FLUSH CACHE ECh IDENTIFY DEVICE EFh SET FEATURE 7. Power Requirements 7.1. Source Voltage +5 V +/-5 % (Operating) +12 V +/-5 % (Operating) +/-8 % (Start up) +/-8 % (Start up) 7.1.1.
8.CD Audio (Test condition: Ordinary temperature) 8.1. Analog Out --- in case of the attenuator is set at 0 dB by the command --(1) Output Level 0.79 V (rms) Typ. (2) Type Unbalanced (3) Load Impedance 47 kOHM min. (4) Frequency Response 20 Hz to 20 kHz +/-3 dB (5) Distortion -73 dB (at 1 kHz JIS A-Weighted) (6) Signal to Noise Ratio 80 dB Typ. (IEC 179 A-weighted) 8.2. Digital Out (1) Output Level (2) Type (3) Load Impedance 0.50 V (p-p) Unbalanced 75 OHM 8.3.Connector 4P connector and 2P connector.
9. Device Configuration Jumper 9.1. Device configuration jumper (MODE SELECT) The device configuration jumper is a 6-pin, right angle and header (Molex P/N70203 or equivalent) with three marked positions. Vcc C S M C S M C S M C S M S L A S A S L A S L A L Cable CSEL (a) (b) Drive CSEL GND (c) Figure 15 (a) Use CS (CSEL) The device shall use the host interface signal CSEL to configure the device. (b) MA (Master): Default Position The device shall use for the Master.
10. Busy Indicator The LED of Front Bezel indicates the drive status. (Busy Indicator) Color: Green (1) After Tray is closed, Busy Indicator start blinking at 0.8 s intervals, and then ----(1-1) Turns off when the drive in the 'Idle' status. 0.8 s Light Off Figure 16 Idle (1-2) Continuously off when no disc is mounted. 0.8 s Light Off Figure 17 No disc (1-3) Continuously on when media has problem 0.8 s Light On Figure 18 Media Problem (2) When playing an audio track, Busy Indicator is blinking at 1.
11.Connection 11.1. Power Supply Cable (1) Housing (2) Contact (3) Cable Length AMP JAPAN P/N 1-480424-0 or equivalent AMP JAPAN P/N 170148-2 or equivalent AWG #28 Max. 2 m 11.2. Interface Cable (1) Connector (2) Cable Specific Impedance Length ATAPI specification 40 core type 100 OHM +/-10 % (without shield) Max. of 0.46 m for total ATAPI bus length 11.3. Audio Cable (1) Capacitance (2) Length Unbalanced and shielded Less than 1000 pF Max. 3 m 12.
13.Safety Standards/Agency Approvals (1) Safety EN60950 UL 1950 CAN/CSA-22.2 No.950 (2) Laser FDA 21CFR (U.S.A.
TOSHIBA TOSHIBA EUROPE GMBH EU-Declaration of Conformity Product: DVD-R/-RW Drive Manufacturer(s): Toshiba Corporation 1-1, Shibaura 1-chome, Minato-ku, Tokyo 105-8001 Japan See page 2 for other locations Model: SD-R5112 Options: None Toshiba declares that the above mentioned product(s) with or without the listed options comply to the EU-Directives and standards as listed on page 2.
29/29 SD-R5112 Rev.1.0 SD-R5112 DVD-R/-RW Drive Address X Related EU-Directive 89/336/EEC Information Technology equipment-Immunity characteristices Limits and methods of masurement CD: 4 kV, ID: 4 kV, AD: 8 kV 3 V/m, 80-1000 MHz, 1 kHz 80 % AM AC-line: 1 kV, I/F 0.5 kV f: 5 kHz, Polarity: +/AC-line: 2 kV/1 kV, Polarity: +/3 V, 0.15-80 MHz, 80 % AM 1 A/m, 50 Hz >95 % 0.5, 30% 25, >95 250 Residental, commercial & light industry Class B Level/Test condition YEA-R3457 2 of 2 Document No.
Deviation List Page Item 2 3.1.Performance (2) Applicable Write Disc DVD-R Rev # 0.9 Rev # 1.0 DVD-R (Ver2.0 for General) DVD-R for General (Ver2.01) Optional Spec. Rev.1.0 DVD-RW (Ver1.1) DVD-RW (Ver1.1) Optional Spec. Rev.1.0 (3) Applicable Read Disc DVD DVD-R (Ver.1.0, Ver.2.0) DVD-R for General (Ver.2.01) 3.2.
Page 22 Item 7.2.8.Write (CD-R 12/16X ZCLV) Write (DVD-R 4X CLV) Rev # 0.9 TBD mA TBD mA Rev # 1.0 650 mA 600 mA 7.2. Current Drain (+12V) 7.2.1.Sleep TBD mA (DVD/CD) 60 mA (DVD/CD) 7.2.2.Standby TBD mA (DVD/CD) 60 mA (DVD/CD) 7.2.3.Continuous Read TBD mA (DVD) TBD mA (CD) 600 mA (DVD) 700 mA (CD) 7.2.4.Idle TBD mA (DVD) 300 mA (DVD) 7.2.5.Average TBD mA (DVD) TBD mA (CD) 600 mA (DVD) 720 mA (CD) 7.2.6.Maximum TBD mA (DVD) TBD mA (CD) 750 mA (DVD) 850 mA (CD) 7.2.7.
