TOSHIBA AMERICA INFORMATION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-M1612 DVD-ROM DRIVE USER MANUAL
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the DVD-ROM Drive ......................................................6 Troubleshooting.......................................................................9 Specifications ........................................................................10 Drive Connectors.........................................
INTRODUCTION – SD-M1612 DVD-ROM Drive General Features Tray Loading Mechanism 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD-ROM DVD DVD-RAM 85ms 95ms 170ms DAE (Digital Audio Extraction) Audio Capability MPC3 Compatibility Multi-Read Capability Regionalization (RPC2 compliance) (DVD) ATAPI BUS Interface: Drive Speed DVD CD DVD-RAM 16X Single Layer 10X Dual Layer 48X 2X (ver 1.0) 1X (ver 2.
CD • • • • • • • • • • • CD-DA CD+(E)G CD-MIDI CD-TEXT CD-ROM CD-ROM-XA CD-I Bridge (Photo-CD, Video CD) CD-I Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) CD-R (Read) CD-RW (Read) Front Panel Figure 1.SD-M1612 DVD-ROM Drive Front Panel Loading Tray Load disc using tray. Busy Indicator When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it attempts to locate the disc. One of the following will occur: • BUSY light goes out.
SETUP – SD-M1612 DVD-ROM The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable (optional) • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the DVD-ROM drive.
Placing DVD-ROM Drive inside your Computer Now that you have set the jumpers, you are ready to install your DVD-ROM drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the DVD-ROM drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system.
Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable. Toshiba's DVD-ROM drives use a standard 4-pin audio cable that can be purchased from most local computer suppliers. The sound cable connects to your sound card at one end and the other end connects to the digital audio connector at the left rear of the DVD-ROM drive (see DVD-ROM drive Back Panel photo for location).
USING THE DVD DVD-ROM Drive – SD-M1612 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.
Removing a Disc To remove a disc from the DVD-ROM drive, perform the following steps: 1. Open the Loading Tray by pressing the Eject Button. 2. Grasp disc by edges, and lift out of loading tray. 3. Press Eject Button again to close Loading Tray. Usage Guidelines • • • • • Keep the disc tray closed when not using the DVD-ROM Drive. Do not press down on the disc tray when opening or closing it. Do not place objects on the disc tray. Never use a damaged, broken, or deformed disc.
NOTE: Use a bar that is less than 1.5 mm in diameter. Do not insert more than 50mm in depth. Inserting more than 50mm may damage the DVD-ROM drive. Handling Media DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD movie skips or hangs during playback, clean the media. Most DVD video playback issues are mediarelated and can be remedied by proper handling and care of media.
TROUBLESHOOTING – SD-M1612 Solution Problem Disc tray cannot be opened • • Check that there is power to drive. Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables).
SPECIFICATIONS –SD-M1612 General Interface ATAPI Compatible DVD-ROM Standards DVD DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) DVD-R, DVD-RW, DVD-RAM CD CD-DA CD-ROM CD-I Bridge (Photo-CD, Video CD) Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) CD-MINI CD-TEXT CD+(E)G CD-ROM-XA CD-I CD-R (Read) CD-RW (Read) Storage Capacities DVD 4.377GB (DVD-5) 7.959GB (DVD-9) 8.754GB (DVD-10) 15.917GB (DVD-18) 3.679GB (DVD-R, Ver. 1.0) 4.377GB (DVD-R, Ver. 2.0) 2.324GB (DVD-RAM, Ver 1.0) 4.377GB (DVD-RAM, Ver 2.
Performance Rotational Speed DVD-ROM (6.0X - 16X) single layer (4.1X - 10X) dual layer DVD-R (Ver 2.0), DVD-RW (2 - 4.8X) DVD-R (Ver 1.0) (2 - 4.8X) DVD-RAM (Ver 1.0) (2X) DVD-RAM (Ver 2.1) (1X) DVD-Video CSS-disc (2 - 4.8X) CD-ROM, CD-R/RW(20.7 - 48X) CD-DA Transfer (14 - 32X) CD-DA/Video CD (4X - 7.
Reliability MTBF Power ON Hours ON/OFF Cycles Number of Access Operating Duty Cycle MTTR 100,000 hours 5,436 hours/year 313 cycles/yea 600,000 accesses/year 20% of Power ON time (Reading/Seeking) 0.5 hours Audio Number of Channels 2 Frequency Response 20Hz to 20,000 Hz Distortion -80 dB (at 1kHz JIS A-weighted) Output Levels Headphone Analog Line Out Digital Line Out 0.90V (rms Typ) 0.79 V (rms Typ) 0.
Power DC Voltage and Current Requirements 5V 5%, 12V 5% +5V Sleep Standby Idle Random Access (average) 280mA 300mA 580mA (DVD) 600mA (CD) 930mA (DVD) 850mA (CD) +12V 0mA 0mA 50mA (DVD) 50mA (CD) 710mA (DVD) 870mA (CD) Physical Height Width Depth Weight 5.75" (146mm) 1.6" (41.5mm) 7.6" (193mm) 2.18lbs (.
DRIVE CONNECTORS –SD-M1612 Figure 1.SD-M1612 DVD-ROM Drive Rear Panel - Connectors Power is supplied to your DVD-ROM drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug has chamfered edges, so the power connector fits only one way. CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upsidedown with power ON. Audio Connectors Supplies Analog and Digital sound to your system.
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO. 1 2 3 4 5 I/O I I/O I/O I/O SIGNAL NAME Reset GND HD7 HD8 HD6 6 7 I/O I/O 8 9 10 11 12 13 14 15 16 17 18 19 20 15 HOST SIGNAL NAME I/O Host Data Bus BIT 7 Host Data Bus BIT 8 Host Data Bus BIT 6 PIN NO.
