MULTIFUNCTIONELE DIGITALE SYSTEMEN Kopieerhandleiding
©2011 TOSHIBA TEC CORPORATION Alle rechten voorbehouden Volgens de copyrightwet mag deze handleiding niet worden gereproduceerd, in welke vorm dan ook, zonder voorafgaande schriftelijke toestemming van TOSHIBA TEC CORPORATION.
Voorwoord Gebruik van deze handleiding Bedankt voor uw aanschaf van het TOSHIBA multifunctionele digitale systeem. Deze handleiding beschrijft het gebruik van de kopieerfuncties van dit multifunctionele systeem. Lees deze handleiding vóór gebruik van dit multifunctionele systeem. Houd deze handleiding bij de hand en maak er gebruik van om een omgeving te configureren waarin de functies van de e-STUDIO ten volle worden benut. Voor dit apparaat is een separate scan-/afdrukfunctie als optie verkrijgbaar.
Displays y De schermen in deze handleiding kunnen afwijken van de echte schermen, afhankelijk van hoe het apparaat gebruikt wordt, zoals de status van de geïnstalleerde opties. y De in deze handleiding opgenomen illustraties van de display zijn voor papier in A/B-formaat. Als u papier van formaat LT gebruikt, kan de display of de volgorde van toetsen in de afbeeldingen verschillen van die van uw multifunctionele systeem.
INHOUD Voorwoord................................................................................................................................. 1 Hoofdstuk 1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Menu BASIS voor de kopieerfuncties..................................................................................... 8 Papier plaatsen ....................................................................................................................... 11 Geschikt kopieerpapier.....................
Stand Roteren en sorteren .................................................................................................. 73 Stand Nieten en sorteren..................................................................................................... 74 Brochure sorteren / Middenvouw / Rughechten .................................................................. 77 Stand Perforatie ..................................................................................................................
Hoofdstuk 6 TEMPLATES Templates.............................................................................................................................. 140 Weergave templatemenu .................................................................................................. 140 Gebruik van “Praktische templates” .................................................................................. 141 Templates vastleggen .................................................................................
6 INHOUD
VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 1. In dit hoofdstuk wordt beschreven wat u moet weten voordat u dit multifunctionele systeem gebruikt, zoals de samenstelling van het menu BASIS voor de kopieerfuncties en de wijze waarop het kopieerpapier wordt geplaatst. Menu BASIS voor de kopieerfuncties .................................................................................... 8 Papier plaatsen........................................................................................................
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Menu BASIS voor de kopieerfuncties Enkele seconden na het inschakelen van de stroomvoorziening verschijnt het menu BASIS voor de kopieerfuncties op het aanraakscherm. Het menu BASIS toont de volgende informatie: 19 18 17 16 15 14 1 2 13 12 3 4 5 6 7 8 9 10 11 1. Gebied voor meldingen Hier verschijnt een korte beschrijving van de functies of de huidige status van dit multifunctionele systeem in de vorm van een melding. 2.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 1.VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 11. [TAAKSTATUS]-toets ( P.162) Deze toets is voor het bevestigen van de verwerkingsstatus van kopieer-, fax-, scan- of afdruktaken, en ook voor het bekijken van de geschiedenis van de resultaten ervan. 12. [PROEFKOPIE]-toets ( P.35) Deze dient voor het maken van een proefkopie ter controle van een afdruk voordat een groot aantal afdrukken wordt gemaakt. 13. Toetsen voor aanpassing dichtheid ( P.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Meldingsgebied systeemstatus In het meldingsgebied voor de status van het systeem wordt de volgende informatie getoond: 5 1 4 3 2 1. Weergave uitvoerlade ( P.37) Deze toont de lade waarheen de afdrukken worden afgevoerd. 2. [UITVOERLADE]-toets ( P.37) Deze dient voor het selecteren van de uitvoerladen. 3. Papierladetoetsen ( P.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Papier plaatsen Geschikt kopieerpapier Het volgende papier kan worden geplaatst en gebruikt voor het kopiëren. De waarden zijn alleen geldig als er door TOSHIBA aanbevolen papier wordt gebruikt. Voor het aanbevolen papier zie de Verkorte installatiehandleiding. y Plaats geen papier van verschillend formaat of van verschillende soort in dezelfde papierlade. y Zorg ervoor dat de papierstapel niet hoger is dan de lijn op de geleidingen.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Ongeschikt kopieerpapier Gebruik geen van de onderstaande soorten papier. Dit kan een papierstoring veroorzaken. y Vochtig papier y Gevouwen papier y Gekruld of gekreukt papier y Papier met een extreem glad of ruw oppervlak Gebruik geen van de onderstaande soorten papier. Dit kan een storing in het multifunctionele systeem veroorzaken.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 1.VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 4 Verplaats de achtergeleider naar de achterrand van het papier terwijl het lagere deel in de richting van de pijlen geduwd wordt. 5 Pas de zijgeleiders aan de papiergrootte aan; houd hierbij de groene hendel van de papiergeleider aan de voorzijde vast. Verstel de papiergeleiders met twee handen. 6 Bevestig dat er geen extra ruimte tussen papier en de zij- of achtergeleiders bestaat.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 9 Onderstaand menu verschijnt. Als het papierformaat of de papiersoort afwijkt van het tevoren in de papierlade gebruikte formaat, druk dan op [NEE] op het aanraakscherm. Als ze hetzelfde zijn, druk dan op [JA]. y Het kan zijn dat bovenstaand menu - afhankelijk van de instelling van het multifunctionele systeem - niet verschijnt. Zie in dat geval de volgende pagina's om de instelling van het papierformaat en de papiersoort te wijzigen: P.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 1.VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Papierformaat vastleggen Wanneer u voor het eerst papier plaatst of het papier door een ander formaat vervangt, dient u het formaat in dit multifunctionele systeem vast te leggen. 1 Druk op de [USER FUNCTIONS]-toets op het bedieningspaneel. 2 Druk op het tabblad [GEBRUIKER] op het aanraakscherm om het instellingenmenu op te roepen en druk vervolgens op [PAPIERLADE].
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 4 16 Druk op [SLUITEN] op het aanraakscherm of op de [USER FUNCTIONS]-toets op het bedieningspaneel.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 1.VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Instelling papiersoort Wanneer u speciaal papier anders dan normaal papier of een soort dat niet voor normaal kopiëren wordt gebruikt plaatst, dient u de dikte en het kenmerk op het multifunctionele systeem in te stellen. y De dikte en het kenmerk kunnen tegelijkertijd worden ingesteld.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 18 2 Druk op het tabblad [GEBRUIKER] op het aanraakscherm om het instellingenmenu op te roepen en druk vervolgens op [PAPIERLADE]. 3 Druk op [PAPIERSOORT]. 4 Selecteer de papiersoort. 1) Selecteer de papierlade waarin het papier is geplaatst. 2) Selecteer de papiersoort. 3) Druk op [OK].
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 1.VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 5 Druk op [OK]. 6 Druk op [SLUITEN] op het aanraakscherm of op de [USER FUNCTIONS]-toets op het bedieningspaneel. Ingestelde papiersoort annuleren Druk op de papierlade-toets in het menu in stap 4 en druk vervolgens op de papiersoort waarvan de instelling moet worden geannuleerd.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 2 Plaats 2 stapels papier in de betreffende rechter- en linkerbak. Waaier het papier goed los en stoot het gelijk voordat u het in de bak legt. Plaats het papier met de kopieerzijde naar boven gekeerd. Plaats een papierstapel in de rechterbak (aangeduid met “A” in de afbeelding) met de zijkant tegen de rechterhoek van de bak en plaats de andere papierstapel in de linkerbak (aangeduid met “B” in de afbeelding) met de zijkant tegen de linkerhoek van de bak.
1 VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM 1.VÓÓR GEBRUIK VAN HET MULTIFUNCTIONELE SYSTEEM Toevoegen van papier in het papierinvoermagazijn tijdens het kopiëren Wanneer het papier in de linker lade van het papierinvoermagazijn tijdens het kopiëren op raakt, verschijnt “Papier voor linker lade toevoegen.” Het papierinvoermagazijn kan uitgetrokken worden, waarna zonder het kopiëren te onderbreken papier in de linker lade kan worden toegevoegd.
2. HET MAKEN VAN KOPIEËN In dit hoofdstuk worden de basiskopieerprocedures toegelicht. Originelen plaatsen ................................................................................................................ 24 Aanvaardbare originelen ......................................................................................................................................24 Functie ter voorkoming van vervalsing .......................................................................................
2 HET MAKEN VAN KOPIEËN Originelen plaatsen Aanvaardbare originelen Wanneer het automatische documentinvoersysteem (optie) wordt gebruikt, kunnen dubbelzijdige originelen automatisch vel voor vel worden gescand. Wanneer de glasplaat voor originelen wordt gebruikt, kunnen originelen zoals overheadtransparanten, calqueerpapier, boekjes of 3-D voorwerpen worden gescand die niet op het automatische documentinvoersysteem kunnen worden geplaatst, alsmede ook normaal papier.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Originelen op de glasplaat voor originelen leggen De glasplaat voor originelen kan worden gebruikt voor originelen zoals overhead-transparanten of calqueerpapier alsmede normale papiervellen die niet op het automatische documentinvoersysteem (optie) kunnen worden geplaatst. Plaats geen zware voorwerpen (4 kg of meer) op de glasplaat voor originelen en oefen er geen kracht op uit. Wanneer het glas breekt, kan dit letsel veroorzaken.
2 HET MAKEN VAN KOPIEËN Boeken U kunt boeken op de glasplaat voor originelen plaatsen. Plaats geen zware voorwerpen (4 kg of meer) op de glasplaat voor originelen en oefen er geen kracht op uit. Wanneer het glas breekt, kan dit letsel veroorzaken. 1 Til de afdekklep (optie) of het automatische documentinvoersysteem (optie) op. 2 Zoek de gewenste pagina in het origineel en leg deze met de te kopiëren zijde naar beneden op de glasplaat. Leg het origineel tegen de linkerbovenhoek op de glasplaat.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Gebruik van het automatische documentinvoersysteem (optie) Aanwijzingen Gebruik geen originelen zoals onder punt 1 t/m 9 aangegeven omdat dergelijke originelen papierfouten of beschadiging van het multifunctionele systeem kunnen veroorzaken. 1. Erg gekreukelde, gevouwen of omgekrulde originelen 2. Originelen met carbonpapier 3. Originelen met plakband, met opgeplakte teksten of geknipte originelen 4.
2 HET MAKEN VAN KOPIEËN Continue invoer De invoer is standaard op “continue invoer” ingesteld. Zodra u de originelen hebt ingesteld en daarna op de [START]-toets drukt, worden ze continu pagina voor pagina gescand. Dit is handig als u meerdere originelen in één keer wilt kopiëren. 1 Leg alle originelen netjes tegen de aanleglijst. 2 Leg de originelen met de af te drukken zijde naar boven en pas de papiergeleiders aan de lengte van de originelen aan.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Enkelvoudige invoer Als de invoer is ingesteld op "enkelvoudige invoer" wordt een origineel automatisch ingevoerd wanneer het op het automatische documentinvoersysteem (optie) wordt gelegd. Dit is handig wanneer u slechts 1 vel wilt kopiëren. P.128 “ADF -> SADF” 1 Pas de papiergeleiders aan de lengte van de originelen aan. 2 Plaats het origineel met de te kopiëren zijde naar boven en recht tegen de papiergeleiders.
2 HET MAKEN VAN KOPIEËN Afdrukken maken Basiskopieerprocedure Maak afdrukken zoals hieronder beschreven. 2 RADF (optioneel) Glasplaat voor originelen OF 1 4 30 3 1 Controleer of er (voldoende) papier in de papierlade(n) zit. 2 Plaats de originelen. 3 Toets het gewenste aantal afdrukken in als u meer dan één afdruk wilt. 4 Selecteer de kopieerinstellingen naar behoefte. Voor de geschikte papiersoorten en -formaten alsmede het plaatsen ervan zie: P.11 “Geschikt kopieerpapier” P.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN 5 Druk op de [START]-toets op het bedieningspaneel. Het kopiëren begint. De afdrukken worden uitgevoerd met de gekopieerde zijde naar beneden. Wees voorzichtig omdat de papieruitvoer en omgeving ervan en het papier zelf na het kopiëren heet zijn. Het onderstaande menu kan verschijnen wanneer speciale programma's worden gebruikt.
2 HET MAKEN VAN KOPIEËN Kopiëren stoppen en opnieuw starten 1 Druk op de [STOP]-toets op het bedieningspaneel. 2 Druk op [STOP OPDR.] op het aanraakscherm om het kopiëren te beëindigen. Druk op [VLGND AFDR] op het aanraakscherm of op de [START]-toets op het bedieningspaneel om weer op te starten. Het kopiëren of scannen wordt onderbroken. Wanneer u op [STOP OPDR.] drukt, worden de gescande gegevens gewist en worden eventuele afdruktaken in de wachtrij uitgevoerd.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Volgend origineel tijdens het kopiëren scannen Zelfs tijdens het uitvoeren van de kopieerfunctie of terwijl “BEDRIJFSKLAAR (OPWARMFASE)” op het aanraakscherm wordt weergegeven, kan het volgende origineel worden gescand (automatische start). 1 Plaats de originelen. 2 Stel het aantal afdruksets en de kopieerinstellingen naar wens in.
2 HET MAKEN VAN KOPIEËN Kopiëren onderbreken en andere afdrukken maken U kunt de huidige afdruktaak onderbreken voor het maken van andere afdrukken (kopiëren met onderbreking). Wanneer de onderbroken taak weer wordt gestart, hoeven de kopieerinstellingen niet opnieuw te worden geselecteerd omdat deze in het geheugen van het multifunctionele systeem zijn opgeslagen.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Proefkopie Wanneer u een groot aantal afdrukken gaat maken, kunt u controleren of deze precies aan uw wensen voldoen door eerst één pagina te kopiëren (proefkopie). Dan kunt u de standen of instellingen wijzigen (bijv. het aantal afdruksets, uitvoerlade, paginanummer, tijdstempel, sorteren/nieten, perforeren) na controle van de proefkopie.
2 HET MAKEN VAN KOPIEËN 6 Wijzig het aantal afdruksets en kopieerinstellingen naar wens na controle van de proefkopie. Standen of instellingen zoals aantal afdruksets, de uitvoerlade, paginanummer, tijdstempel, sorteren/nieten en perforeren kunnen worden gewijzigd. Indien u instellingen zoals de reproductiefactor, de densiteit, de modus voor originelen of enkel/dubbelzijdig kopiëren wilt wijzigen, moet u de proefkopie eerst voltooien. Wijzig deze instellingen en scan het origineel opnieuw.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Uitvoerlade selecteren U kunt de uitvoerlade selecteren als er een optionele finisher voor de binnenste lade is geïnstalleerd. y De beschikbare uitvoerlade kan onderhevig zijn aan beperkingen, afhankelijk van kopieerinstellingen en papierformaten. y De uitvoerladeselectie is standaard op automatische selectie ingesteld. De uitvoerlade wijzigen De momenteel geselecteerde uitvoerlade wordt weergegeven in het meldingsgebied voor de status van het systeem.
2 HET MAKEN VAN KOPIEËN Kopiëren met handinvoer Wanneer u afdrukken op overhead-transparanten, etiketten, enveloppen of een niet-standaard papierformaat maakt, leg het kopieerpapier dan in de handinvoerbak. Kopiëren met handinvoer is ook raadzaam voor het kopiëren op standaard papierformaat dat niet in een van de papierladen aanwezig is. Wanneer u het papierformaat selecteert, kunt u verschillende functies gebruiken zoals de automatische papierselectie (APS) of de automatische zoomselectie (AMS).
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Papierformaat Standaardformaat Anders dan Noord-Amerika: A3, A4, B4, B5 Noord-Amerika: LD, LT, LG, ST-R Werkwijze P.39 “Kopiëren op A3-, A4-, B4- en B5-formaat (op multifunctioneel systeem behalve voor Noord-Amerika) / LD-, LT-, LG- en ST-R-formaat (op multifunctioneel systeem voor Noord-Amerika)” Behalve bovenstaande P.42 “Kopiëren op andere dan bovenstaande standaard papierformaten” Envelop P.
2 HET MAKEN VAN KOPIEËN 4 Selecteer de toets voor hetzelfde formaat onder “KOPIE” als van het papier dat in de handinvoerbak is geplaatst. Het papierformaat is nu ingesteld. Als het papierformaat niet in deze stap wordt geselecteerd, kan het kopiëren worden vertraagd. 40 5 Druk op [PAPIERSOORT] op het aanraakscherm als de papiersoort in de handinvoerbak anders is dan normaal papier. 6 Druk op de toets voor dezelfde papiersoort als dat van het papier dat in de handinvoerbak is geplaatst.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN y Indien u een verkeerde papiersoort selecteert, kunnen papierstoringen of aanzienlijke afdrukproblemen ontstaan. y Wanneer u een papiersoort selecteert, kunt u deze bevestigen door middel van de pictogrammen zoals weergegeven in het onderstaande meldingsgebied voor de status van het systeem.
2 HET MAKEN VAN KOPIEËN Kopiëren op andere dan bovenstaande standaard papierformaten 1 Plaats de originelen en het papier op dezelfde wijze zoals beschreven in stap 1 t/m 3 in “Kopiëren op A3-, A4-, B4- en B5-formaat (op multifunctioneel systeem behalve voor Noord-Amerika) / LD-, LT-, LG- en ST-R-formaat (op multifunctioneel systeem voor Noord-Amerika)” ( P.39) 2 Druk op [INSTELLING FORMAAT] op het aanraakscherm.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN 5 Druk op [PAPIERSOORT] als het papier in de handinvoerbak geen normaal papier is. 6 Druk op de toets voor dezelfde papiersoort als dat van het papier dat in de handinvoerlade is geplaatst. Druk daarna op [OK]. y Indien u een verkeerde papiersoort selecteert, kunnen papierstoringen of aanzienlijke afdrukproblemen ontstaan.
2 HET MAKEN VAN KOPIEËN Kopiëren op een envelop y De geschikte envelopformaten zijn als volgt: DL (110 mm x 220 mm), COM10 (4 1/8" x 9 1/2"), Monarch (3 7/8" x 7 1/2"), CHO-3 (120 mm x 235 mm), YOU-4 (105 mm x 235 mm) y Raadpleeg de Verkorte installatiehandleiding voor de aanbevolen enveloppen. Opmerkingen bij gebruik van enveloppen Gebruik de volgende enveloppen niet omdat dit kan leiden tot vastlopen van het papier of beschadiging van de apparatuur. 1.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN 2 Plaats de envelop op een vlak, schoon oppervlak en druk er met uw handen op in de richting van de pijl om lucht te laten ontsnappen. Druk er goed op om te voorkomen dat de rand naar boven rolt. Corrigeer omgevouwen hoeken van de envelop. 3 Trek de papierklemhendel naar de buitenzijde. Leg de envelop met de te bedrukken zijde naar beneden in de handinvoerbak. 1 Plaats de envelop met de rand naar binnen naar de voorkant.
2 HET MAKEN VAN KOPIEËN 6 Druk op de toets voor hetzelfde formaat als dat van de envelop dat in de handinvoerbak is geplaatst. Het formaat van de geselecteerde envelop wordt als formaat “OVERIGE” vastgelegd. 7 Druk op [OVERIGE] onder KOPIE. De papiergrootte wordt nu ingesteld op de grootte van de envelop die in de handinvoerbak geplaatst is. Het papiertype wordt automatisch ingesteld op [ENVELOP].
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Afdrukken met handinvoer op niet-standaard papierformaat U kunt niet-standaard papierformaten gebruiken zoals aan de rechterzijde weergegeven. 148 - 432 mm (5.8" - 17") 100 - 297 mm (3.9" - 11.7") 1 Leg het origineel op de glasplaat. 2 Trek de papierklemhendel naar de buitenzijde. Leg het papier met de af te drukken zijde naar beneden in de handinvoerbak. 1 2 y De papierstapel mag niet hoger zijn dan de aanduiding op de papiergeleiders.
2 HET MAKEN VAN KOPIEËN 5 Toets de afmeting in. 1) Druk op [LENGTE] en toets de waarde in (100 mm tot 297 mm). 2) Druk op [BREEDTE] en toets de waarde in (148 mm tot 432 mm). 3) Druk op [OK]. Lengte en breedte worden aangeduid zoals aan de rechterzijde weergegeven: Breedte Lengte Druk, om de eerder opgeslagen afmetingsgegevens op te roepen, op de betreffende toets [GEHEUGEN 1] t/m [GEHEUGEN 4] en druk vervolgens op [OK]. Voor het opslaan in het geheugen van afmetingsgegevens zie: P.
2 HET MAKEN VAN KOPIEËN 2.HET MAKEN VAN KOPIEËN Niet-standaardformaat in het geheugen opslaan 1 Ga te werk zoals beschreven in stap 1 t/m 4 in “Afdrukken met handinvoer op nietstandaard papierformaat” ( P.47). 2 Sla afmetingen in het geheugen op. 1) 2) 3) 4) Selecteer een gewenst geheugennummer. Druk op [LENGTE] en toets de waarde in (100 mm tot 297 mm). Druk op [BREEDTE] en toets de waarde in (148 mm tot 432 mm). Druk op [GEHEUGEN].
3. BELANGRIJKSTE KOPIEERFUNCTIES In dit hoofdstuk worden de belangrijkste kopieerfuncties, zoals wijziging van de reproductiefactor, instelling van de sorteerstanden en uitvoering van dubbelzijdig kopiëren, beschreven. Vóór gebruik van de kopieerfuncties ................................................................................... 52 Standaardinstellingen ...........................................................................................................................................
3 BELANGRIJKSTE KOPIEERFUNCTIES Vóór gebruik van de kopieerfuncties Standaardinstellingen Dit multifunctionele systeem start op met de “standaardinstellingen” wanneer de stroomvoorziening wordt ingeschakeld. Maar als er nog geen wijziging in instellingen is toegepast, komen de instellingen van het multifunctionele systeem weer op de standaardwaarden te staan wanneer de energiebesparingsstand wordt gewist of er op de [FUNCTION CLEAR]toets op het bedieningspaneel wordt gedrukt.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Ingestelde functies annuleren Als u een kopieerfunctie-instelling wilt annuleren, druk dan op [RESET] in het bijbehorende instelmenu. Alle gewijzigde instellingen annuleren Wanneer u op de [FUNCTION CLEAR]-toets op het bedieningspaneel drukt, worden alle functiewijzigingen geannuleerd.
3 BELANGRIJKSTE KOPIEERFUNCTIES Papierselectie Automatische papierselectie (APS) Het multifunctionele systeem detecteert het formaat van het origineel en selecteert automatisch hetzelfde formaat kopieerpapier. Deze functie heet automatische papierselectie (APS). y Voor de origineelformaten die kunnen worden gedetecteerd zie: P.24 “Aanvaardbare originelen” y Sommige origineelformaten kunnen niet met deze functie worden gedetecteerd. Selecteer het gewenste formaat in dat geval handmatig. P.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Gewenste papier handmatig selecteren U dient het papier zelf te selecteren als de volgende originelen worden gekopieerd waarvan de formaten niet correct kunnen worden gedetecteerd: y Zeer transparante originelen (bijv. overhead-transparanten, calqueerpapier) y Geheel donkere originelen of originelen met donkere randen y Originelen met niet-standaard formaat (bijv.
3 BELANGRIJKSTE KOPIEERFUNCTIES Originelen met verschillende formaten in één keer kopiëren U kunt een set originelen met verschillende formaten met behulp van het automatische documentinvoersysteem (optie) kopiëren. De volgende origineelformaten kunnen worden gecombineerd: Noord-Amerika: LD, LG, LT, LT-R, COMP Anders dan Noord-Amerika: A3, A4, A4-R, B4, B5, FOLIO 1 Vul de papierlade(n) met papier.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES 4 Druk op [GEMENGD]. 5 Druk op [AMS] om afdrukken te maken op papier van één formaat. Om afdrukken te maken op papier van hetzelfde formaat als de originelen druk op [OK] of [AFBREKEN] zodat het menu terugkeert naar het menu BASIS en druk vervolgens op [APS].
3 BELANGRIJKSTE KOPIEERFUNCTIES Instelling Modus voor originelen U kunt afdrukken met de optimale afdrukkwaliteit maken door de volgende modi voor uw origineel te selecteren. TEKST/FOTO: Originelen met zowel tekst als foto's TEKST: Originelen met alleen tekst (of tekst en lijntekeningen) FOTO: Originelen met foto's KLEURENDOCUMENT: Kleurenoriginelen, zoals presentatiedocumenten Wanneer “KLEURENDOCUMENT” is ingesteld, is de reproductiefactor in te stellen tussen 25 en 400%.
3 BELANGRIJKSTE KOPIEERFUNCTIES Densiteitaanpassing Het multifunctionele systeem detecteert het densiteitniveau van originelen en past het densiteitniveau van het gekopieerde beeld automatisch voor een optimaal resultaat aan. Ook kunt u het handmatig aan het gewenste niveau aanpassen. Automatisch instellen (automatische densiteitaanpassing) Druk op [AUTOM.] op het aanraakscherm. De automatische aanpassing voor dichtheid wordt standaard bij het installeren ingesteld.
3 BELANGRIJKSTE KOPIEERFUNCTIES Vergroten en verkleinen U kunt de reproductiefactor van gekopieerde beelden als volgt wijzigen: Automatische zoomselectie (AMS): Specificeer vooraf het formaat van het kopieerpapier dat wordt gebruikt. Het multifunctionele systeem bepaalt het origineelformaat en selecteert automatisch de optimale reproductiefactor voor het formaat van het kopieerpapier.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES 3 Selecteer het gewenste papierformaat, druk op [AMS] en vervolgens op [OK]. y Indien u een ander papierformaat wilt selecteren dan hieronder aangegeven, moet u het formaat als “OVERIGE” vastleggen. Zodra u dit formaat heeft vastgelegd, wordt het geactiveerd telkens wanneer u op [OVERIGE] op het aanraakscherm drukt. Noord-Amerika: LD, LG, LT, ST Anders dan Noord-Amerika: A3, A4, B4, B5 Voor de werkwijze bij het vastleggen zie: P.
3 BELANGRIJKSTE KOPIEERFUNCTIES Zowel het origineelformaat als het kopieerpapierformaat afzonderlijk specificeren 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [ZOOM] op het aanraakscherm. 4 Selecteer het gewenste formaat voor het origineel en het kopieerpapier en druk vervolgens op [OK]. y Indien u een ander formaat wilt selecteren dan hieronder voor origineel en kopieerpapier aangegeven, moet u het formaat als “OVERIGE” vastleggen.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Papierformaten onder “OVERIGE” formaat vastleggen Indien u een ander formaat wilt selecteren dan hieronder voor origineel en kopieerpapier aangegeven, moet u het formaat op de volgende wijze als “OVERIGE” vastleggen. Zodra u dit formaat heeft vastgelegd, wordt het geactiveerd telkens wanneer u op [OVERIGE] op het aanraakscherm drukt.
3 BELANGRIJKSTE KOPIEERFUNCTIES De reproductiefactor handmatig specificeren 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [ZOOM] op het aanraakscherm. 4 Druk op de hieronder weergegeven toetsen voor het selecteren van de gewenste reproductiefactor. [ OMHOOG] en [ OMLAAG] toetsen De reproductiefactor verandert telkens 1% wanneer een van de toetsen wordt ingedrukt. Wanneer een van beide ingedrukt wordt gehouden, wordt de factor automatisch verhoogd resp. verlaagd.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES 5 Selecteer het gewenste formaat en druk vervolgens op [OK]. y Indien u een ander papierformaat wilt selecteren dan hieronder aangegeven, moet u het formaat als “OVERIGE” vastleggen. Zodra u dit formaat heeft vastgelegd, wordt het geactiveerd telkens wanneer u op [OVERIGE] op het aanraakscherm drukt. Noord-Amerika: LD, LG, LT, ST Anders dan Noord-Amerika: A3, A4, B4, B5 Voor de werkwijze bij het vastleggen zie: P.
3 BELANGRIJKSTE KOPIEERFUNCTIES Afwerkfunctie selecteren Afwerkfuncties en als optie leverbare afwerkapparaten Zie onderstaande tabel voor elke afwerkfunctie. Afwerkfunctie Sorteren uit nieten uit Sorteren ( P.71) Groeperen ( Afdrukken worden in dezelfde paginavolgorde als de originelen set voor set uitgevoerd. P.71) Roteren en sorteren ( Omschrijving Afdrukken worden zonder te sorteren of te nieten uitgevoerd. Afdrukken worden per pagina gegroepeerd uitgevoerd. P.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Controleer de afwerkfuncties die bij elk afwerkapparaat worden geactiveerd.
3 BELANGRIJKSTE KOPIEERFUNCTIES Naam van elk onderdeel van de finishers (optie) MJ-1101 1 6 2 5 3 1. 2. 3. 4. 5. 6. Bovenste uitvoerbak Onderste uitvoerbak Secundaire bak Klep voorzijde Perforatie-eenheid MJ-6103 Bedieningseenheid voor nieten 1. 2. 3. 4. 5. 6. 7. 8. Bovenste uitvoerbak Onderste uitvoerbak Secundaire bak Bak voor rughechten Opvang Klep voorzijde Perforatie-eenheid MJ-6103 Bedieningseenheid voor nieten 1. 2. 3. 4. 5.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES MJ-1033 1 6 1. 2. 3. 4. 5. 6. 2 3 Bovenste klep Bak Secundaire bak Bak voor rughechten Klep voorzijde Perforatie-eenheid MJ-6008 5 4 Naam van elk onderdeel van de binnenste lade (optie) MJ-5004 1 1. Bak 2. Opvang papier 2 MJ-5005 1 1.
3 BELANGRIJKSTE KOPIEERFUNCTIES MJ-5006 1 70 Afwerkfunctie selecteren 1.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Modus Sorteren/Groeperen Wanneer u meer dan één set afdrukken maakt, kunnen deze in dezelfde paginavolgorde als die van de originelen worden uitgevoerd. Deze modus heet sorteren. Afdrukken kunnen ook per pagina gegroepeerd worden uitgevoerd. Deze modus heet groeperen.
3 BELANGRIJKSTE KOPIEERFUNCTIES 72 4 Selecteer [SORT] of [GROEP] en druk vervolgens op [OK]. 5 Toets het gewenste aantal afdrukken in. 6 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Stand Roteren en sorteren Wanneer u meer dan één set afdrukken maakt, kan elke set bovenop een andere set afwisselend in staande en liggende richting worden uitgevoerd. Deze modus heet roteren en sorteren. Gebruik 2 papierladen en 2 stapels papier van hetzelfde formaat. Leg één stapel papier in staande richting in de ene papierlade en de andere stapel in liggende richting in de andere lade voordat met kopiëren wordt begonnen.
3 BELANGRIJKSTE KOPIEERFUNCTIES 4 Selecteer [ROTEREN] en druk vervolgens op [OK]. 5 Toets het gewenste aantal afdrukken in. 6 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel. Stand Nieten en sorteren Wanneer meer dan één set afdrukken wordt gemaakt, kan het gekopieerde papier automatisch set voor set geniet worden. Deze modus heet nieten en sorteren. Er kan gekozen worden uit drie verschillende nietposities.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES 3 Druk op [AFWERKING] op het aanraakscherm. 4 Selecteer de gewenste positie van de nietjes: [VOOR NIETEN], [DUBBEL NIETEN] of [NIETEN ACHTER] en druk vervolgens op [OK]. 5 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel.
3 BELANGRIJKSTE KOPIEERFUNCTIES Finisher voor rughechten MJ-1106 Papiergewicht Papierformaat g/m2 64 - 80 (17 - 20 lb. Bond) 81 - 90 g/m2 (21 - 24 lb. Bond) 91 - 105 g/m2 (25 - 28 lb. Bond) A4 *1, B5, LT *1 50 vel 30 vel 30 vel A3, A4-R, B4, FOLIO, LD, LG, LT-R, COMP 30 vel 15 vel 15 vel *1 De capaciteit van de uitvoerlade bedraagt 30 sets. Binnenste finisher MJ-1032 / Finisher met rughechting MJ-1033 Papiergewicht Papierformaat g/m2 64 - 80 (17 - 20 lb. Bond) 81 - 90 g/m2 (21 - 24 lb.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Brochure sorteren / Middenvouw / Rughechten U kunt meer dan één origineel kopiëren en de afdrukken tot een boekje samenvoegen (brochure sorteren). Bij de finisher voor rughechten is het ook mogelijk het gekopieerde boekje in het midden te vouwen (middenvouw) en te nieten (rughechten). Optie Middenvouw is alleen beschikbaar wanneer de Finisher met rughechting MJ-1106 (optie) geïnstalleerd is.
3 BELANGRIJKSTE KOPIEERFUNCTIES Eisen met betrekking tot middenvouw Finisher voor rughechten MJ-1106 Papierformaat A3, A4-R, B4, LD, LT-R, LG Papiergewicht g/m2 64 - 105 (17 - 28 lb. Bond) Maximaal aantal voor middenvouw beschikbare vellen *1 25 vel Maximaal aantal sets in bak voor rughechten 21 - 25 vel/set: 5 sets 16 - 20 vel/set: 6 sets 11 - 15 vel/set: 8 sets 6 - 10 vel/set: 12 sets Minder dan 5 vel/set: 25 sets *1 Er kan 1 kaftblad (64 tot 256 g/m2 (17 lb. Bond tot 140 lb.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES 1 Vul de papierlade(n) met papier. Speciaal papier zoals overhead-transparanten of etiketten is niet van toepassing. 2 Selecteer het gewenste papierformaat. Er kan papier van formaat A3, A4-R, A5-R *1, B4 of B5-R *1 worden gebruikt. *1 A5-R en B5-R zijn alleen geschikt voor de stand Brochure sorteren. 3 Plaats de originelen. 4 Druk op [AFWERKING] op het aanraakscherm.
3 BELANGRIJKSTE KOPIEERFUNCTIES 6 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel. 7 Voeg het gekopieerde papier samen als de stand Uitvouwblad of de stand Brochure sorteren & uitvouwblad wordt gebruikt. In de stand Uitvouwblad, wordt er voor iedere 5 vellen papier in het midden gevouwen voordat het uitgevoerd wordt. Als er meer dan 5 vel papier worden gekopieerd, voeg ze dan samen zoals aangegeven in de afbeelding.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Stand Perforatie Afdrukken kunnen worden geperforeerd als de perforatie-eenheid (optie) op de finisher is geïnstalleerd. y Papierformaten 3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R en COMP alsmede papiergewichten van 64 tot 209 g/m2 (17 lb. Bond tot 110 lb. Index) (MJ-6103) en 64 tot 128 g/m2 (17 tot 34 lb. Bond) (MJ-6007/MJ6008) zijn hiervoor geschikt.
3 BELANGRIJKSTE KOPIEERFUNCTIES Stand Handmatig nieten U kunt afdrukken handmatig nieten zonder te kopiëren. Dit is handig wanneer u vóór het kopiëren vergeten bent nieten en sorteren in te stellen of wanneer u originelen wilt nieten. (Alleen beschikbaar bij de finisher MJ-1101 of finisher voor rughechten MJ-1106) Maximaal aantal vellen voor handmatig nieten Papiergewicht Papierformaat g/m2 64 - 80 (17 - 20 lb. Bond) 81 - 90 g/m2 (21 - 24 lb. Bond) 91 - 105 g/m2 (25 - 28 lb.
3 BELANGRIJKSTE KOPIEERFUNCTIES Dubbelzijdig kopiëren U kunt een enkelzijdig origineel naar een dubbelzijdige afdruk kopiëren en omgekeerd of een dubbelzijdig origineel naar een dubbelzijdige afdruk. Dit is handig wanneer u papier wilt besparen of wanneer u een boek met behoud van de juiste paginavolgorde wilt kopiëren. Enkelzijdig origineel -> enkelzijdige afdruk ( P.84) Dubbelzijdig origineel -> enkelzijdige afdruk ( P.84) Enkelzijdig origineel -> dubbelzijdige afdruk ( P.
3 BELANGRIJKSTE KOPIEERFUNCTIES Een enkelzijdige afdruk maken Bij het kopiëren van dubbelzijdige staande originelen die maar aan één zijde van het papier naar links/rechts zijn geopend, moet de functie Beeldrichting in het menu BEWERKEN worden gebruikt zodat alle afdrukken in de juiste richting worden uitgevoerd. P.125 “Beeldrichting” “AFDRUKRICHTING” instellen 84 Geen instelling 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [DUBBELZIJDIG] op het aanraakscherm.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES Een dubbelzijdige afdruk maken Wanneer enkelzijdige staande originelen in liggende richting zijn geplaatst en op beide zijden van het papier worden gekopieerd, zijn de afdrukken meestal in naar boven/beneden geopende richting. U kunt afdrukken maken in naar links/rechts geopende richting met behulp van de functie Beeldrichting. P.125 “Beeldrichting” “AFDRUKRICHTING” instellen Geen instelling 1 Vul de papierlade(n) met papier.
3 BELANGRIJKSTE KOPIEERFUNCTIES Een dubbelzijdige afdruk van een boek maken U kunt dubbelzijdige afdrukken maken van boeken of catalogi in de juiste paginavolgorde. A4-, B5- en LT-formaat zijn mogelijk. 86 1 Vul de papierlade(n) met papier. 2 Druk op [DUBBELZIJDIG] op het aanraakscherm. 3 Selecteer [BOEK -> 2]. Stel bij gebruik van de functie kopiëren met handinvoer het papierformaat in.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES 4 Selecteer de boekkopieerfunctie. Voorbeeld: Wanneer pagina 2 t/m 6 van een boek geopend naar links moeten worden gekopieerd, selecteer [LINKS -> LINKS]. 2 5 3 6 7 Druk op [OK]. Het menu keert terug naar het menu BASIS. 6 Druk op de toets voor de papierlade met het gewenste papierformaat. Alleen A4-, B5- en LT-formaat zijn mogelijk.
3 BELANGRIJKSTE KOPIEERFUNCTIES 7 Selecteer naargelang nodig andere kopieerinstellingen. 8 Leg het origineel op de glasplaat. Als voor de afdruk een inbindruimte nodig is, selecteer dan de functie boekinbindruimte in het menu BEWERKEN. P.97 “Inbindruimte creëren” Plaats het origineel met de onderzijde naar u toe gekeerd en lijn het midden ervan uit met de gele lijn onder de glasplaat. Plaats geen zware voorwerpen (4 kg of meer) op de glasplaat voor originelen en oefen er geen kracht op uit.
3 BELANGRIJKSTE KOPIEERFUNCTIES Opslaan als bestand uitvoeren Met de functie Opslaan als bestand kunt u de gekopieerde gegevens in de gedeelde map van de harde schijf van het multifunctionele systeem of een opgegeven pc in een netwerk opslaan. De gegevens kunnen als PDF-, TIFF- of XPSbestand worden opgeslagen. y Functie “OPSLAAN ALS BESTAND” is alleen beschikbaar wanneer de scannerkit of de printer-/scannerkit (beide opties) geïnstalleerd is.
3 BELANGRIJKSTE KOPIEERFUNCTIES 4 Druk op de desbetreffende toetsen voor de invoer van informatie over de gegevens die moeten worden opgeslagen. Druk daarna op [OK]. MFP LOKAAL: Druk hierop om de gegevens in de gedeelde map van het multifunctionele systeem op te slaan. NETWERK 1, NETWERK 2: Druk op een van de twee om de gegevens op te slaan in de gedeelde map van een pc die via een netwerk met het multifunctionele systeem is verbonden.
3 BELANGRIJKSTE KOPIEERFUNCTIES 3.BELANGRIJKSTE KOPIEERFUNCTIES 7 Als alle originelen zijn gescand, drukt u op [OPDR. GEREED] op het aanraakscherm. Het kopiëren en opslaan begint. Instelling gedeelde map Wanneer een gebruiker die gemachtigd is een gedeelde map te wijzigen, op [NETWERK 1] of [NETWERK 2] heeft gedrukt, verschijnt het menu voor het opgeven van een index. De instellingsitems verschillen afhankelijk van het te gebruiken bestandsoverdrachtsprotocol.
3 BELANGRIJKSTE KOPIEERFUNCTIES SMB Door op een van de onderstaande toetsen te drukken verschijnt het toetsenbord op het scherm. Voer in met de toetsen op het aanraakscherm of de numerieke toetsen op het bedieningspaneel. Druk na beëindiging van de invoer op [OK]. NETWERK PAD: Druk hierop voor de invoer van een netwerkpad voor de map waarin de gegevens moeten worden opgeslagen. LOGIN GEB. NAAM: Druk hierop voor de invoer van een gebruikersnaam voor de toegang tot de netwerkmap. Voer zoals vereist in.
4. BEWERKEN-FUNCTIES In dit hoofdstuk wordt het gebruik van de verschillende kopieerfuncties in het menu BEWERKEN beschreven. Weergave menu BEWERKEN................................................................................................ 94 Beeld verplaatsen................................................................................................................... 95 Marge boven/onder of marge links/rechts creëren .............................................................................
4 BEWERKEN-FUNCTIES Weergave menu BEWERKEN U kunt het menu BEWERKEN oproepen door op het tabblad [BEWERKEN] op het aanraakscherm te drukken wanneer u de verschillende bewerken-functies wilt gebruiken. Het menu BEWERKEN omvat 2 pagina's. Om tussen de pagina's te schakelen druk op 94 Weergave menu BEWERKEN of .
4 BEWERKEN-FUNCTIES Beeld verplaatsen U kunt een inbindruimte creëren door een beeld naar de linker-, rechter-, boven- of onderzijde van het kopieerpapier te verplaatsen. Deze functie heet “beeld verplaatsen”. Dit is handig wanneer u een stapel papier na het kopiëren wilt perforeren of nieten. Met deze functie kunt u eenvoudig een inbindruimte creëren wanneer u een boek op beide zijden van het papier kopieert.
4 BEWERKEN-FUNCTIES 5 Stel de breedte van de inbindruimte in. 1) Druk op [VOOR] en stel de breedte van de inbindruimte aan de voorzijde in met behulp van [ 0 mm] en [ 100 mm]. (De breedte aan de achterzijde wordt op dezelfde wijze ingesteld.) 2) Druk op [ACHTER] en stel de breedte van de inbindruimte aan de achterzijde in met behulp van [ 0 mm] en [ 100 mm]. (Alleen de breedte aan de achterzijde wordt ingesteld.) 3) Druk op [OK].
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES Inbindruimte creëren U kunt eenvoudig een inbindruimte creëren bij het kopiëren van een boek op beide zijden van het papier. P.86 “Een dubbelzijdige afdruk van een boek maken” 1 Druk op [SCHUIF BEELD] in het menu BEWERKEN. 2 Druk op [BOEK]. 3 Stel de breedte van de inbindruimte in. 1) Druk op [ 0 mm] of [ 2) Druk op [OK]. 30 mm].
4 BEWERKEN-FUNCTIES 4 Druk op [OK]. Selecteer ook “Boek -> dubbelzijdige afdruk". P.
4 BEWERKEN-FUNCTIES Rand wissen U kunt de rand van een gekopieerd beeld wit maken wanneer een schaduwachtig donker gedeelte erop verschijnt. Deze functie heet “rand wissen”. Dit is handig wanneer u het gekopieerde beeld netjes en schoon wilt maken als de rand van het origineel vuil of gescheurd is. Alleen originelen met standaardformaat zijn mogelijk. 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [RAND WISSEN] in het menu BEWERKEN.
4 BEWERKEN-FUNCTIES Boekmidden wissen U kunt het midden van het gekopieerde beeld wit maken wanneer een schaduwachtig gedeelte erop verschijnt. Deze functie heet “boekmidden wissen”. Dit is handig bij het kopiëren van boeken. Boekmidden wissen instellen 100 1 Vul de papierlade(n) met papier. 2 Selecteer de papierlade voor het gewenste papierformaat. 3 Druk op [BOEKMIDDEN WISSEN] in het menu BEWERKEN. Stel bij gebruik van de functie kopiëren met handinvoer het papierformaat in.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 4 Stel de breedte van het te wissen gedeelte in. 5 Leg het origineel op de glasplaat. 1) Druk op [ 2 mm] of [ 2) Druk op [OK]. 50 mm]. Plaats het origineel met de onderzijde naar u toe gekeerd en lijn het midden ervan uit met de gele lijn onder de glasplaat. Plaats geen zware voorwerpen (4 kg of meer) op de glasplaat voor originelen en oefen er geen kracht op uit. Wanneer het glas breekt, kan dit letsel veroorzaken.
4 BEWERKEN-FUNCTIES Dubbele pagina U kunt de 2 tegenoverliggende pagina's van een boek of 2 originelen naast elkaar op 2 aparte vellen of op beide zijden van 1 vel papier kopiëren. Deze functie heet “dubbele pagina”. U hoeft het origineel op de glasplaat niet te verschuiven. -12- -13- -12- -13- Alleen A4-, B5- en LT-formaat zijn mogelijk. 102 1 Vul de papierlade(n) met papier. 2 Druk op [TWEE PAG.] in het menu BEWERKEN. 3 Druk op [1-ZIJDE] of [2-ZIJDIG].
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 5 Druk op het tabblad [BASIS] voor de weergave van het menu BASIS en selecteer vervolgens A4, B5 of LT als kopieerpapierformaat. Stel bij gebruik van de functie kopiëren met handinvoer het papierformaat in. 6 Open de gewenste pagina en leg deze op de glasplaat voor originelen. Plaats het origineel met de onderzijde naar u toe gekeerd en lijn het midden ervan uit met de gele lijn onder de glasplaat.
4 BEWERKEN-FUNCTIES 2IN1 / 4IN1 U kunt 2 of 4 originelen op 1 vel papier kopiëren door deze te verkleinen. Deze functie heet “2IN1” of “4IN1”. Bij het gebruik van deze functie in combinatie met dubbelzijdig kopiëren kunt u in totaal 8 afdrukken op 1 vel papier maken. De onderstaande afbeeldingen tonen hoe u de afdrukken kunt rangschikken.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 1 Vul de papierlade(n) met papier. Stel bij gebruik van de functie kopiëren met handinvoer het papierformaat in. Als u een papierformaat selecteert dat afwijkt van dat van het origineel, druk dan op [ZOOM] in het menu BASIS. Selecteer vervolgens het gewenste papierformaat, druk op [AMS] en dan op [OK] in het onderstaande menu. 2 Plaats de originelen. 3 Druk op [2IN1 / 4IN1] in het menu BEWERKEN. 4 Voer instelling 2IN1 / 4IN1 uit.
4 BEWERKEN-FUNCTIES 5 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel. Als de originelen op het automatische documentinvoersysteem (optie) zijn geplaatst, begint het scannen en kopiëren. Voer stap 6 en 7 uit als deze op de glasplaat voor originelen zijn geplaatst. 6 Plaats het volgende origineel en druk vervolgens op [VLGND AFDR] op het aanraakscherm of op de [START]-toets op het bedieningspaneel.
4 BEWERKEN-FUNCTIES Stand Brochure sorteren U kunt meer dan één origineel kopiëren in boekpaginavolgorde. Deze modus heet Brochure sorteren. Deze functie kan worden gecombineerd met het vouwen en nieten van de gekopieerde pagina's in het midden. Deze modus heet Brochure sorteren & rughechten. Brochure sorteren 1 6 2 7 4 3 2 12 9 11 Brochure sorteren & rughechten 1 2 6 7 3 12 Brochure sorteren kan ook in het menu BASIS worden geselecteerd. Raadpleeg de volgende pagina voor meer informatie: P.
4 BEWERKEN-FUNCTIES 4 Druk op [BROCHURE SORTEREN] in het menu BEWERKEN. 5 Stel de stand rughechten en de inbindruimte naar wens in. 1) Druk bij de instelling van rughechten op [NIETEN AAN]. Hoeft er niet geniet te worden, druk dan op [NIETEN UIT]. 2) Druk op [ 2 mm] of [ 30 mm] voor de instelling van de breedte van de inbindruimte. 3) Druk op [OK]. Voor het maximale aantal mogelijke vellen voor rughechten zie: P.
4 BEWERKEN-FUNCTIES Beeld bewerken U kunt de verschillende hieronder weergegeven bewerken-functies voor gescande beelden selecteren. Trimmen: U kunt een bepaald gebied van een origineel selecteren en alleen dit kopiëren. Maskeren: U kunt een bepaald gebied van een origineel maskeren en alleen het ongemaskeerde gebied kopiëren. Spiegelbeeld: U kunt een pagina in spiegelbeeld afdrukken. Negatief/positief-omkering: U kunt het zwart en wit van een pagina omkeren.
4 BEWERKEN-FUNCTIES 3 Selecteer [TRIM] of [MASK]. 4 Leg het origineel met de af te drukken zijde naar boven op de glasplaat. Plaats het met de onderzijde naar u toe gekeerd. Lijn de linkerbovenhoek uit met die van de glasplaat zodat het origineel tegen de aanleglijst ligt. Plaats geen zware voorwerpen (4 kg of meer) op de glasplaat voor originelen en oefen er geen kracht op uit. Wanneer het glas breekt, kan dit letsel veroorzaken.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 6 7 Toets de afgelezen waarden in. 1) Druk op [X1], [X2], [Y1] en [Y2] en toets vervolgens de bijbehorende afgelezen waarden in. 2) U kunt maximaal 4 gebieden op 1 pagina aangeven. Als u meer dan één gebied wilt aangeven, druk dan op [GEBIED 1] tot [GEBIED 4] om van gebied te wisselen en toets vervolgens de bijbehorende waarden in. 3) Druk op [OK] nadat u alle gebieden hebt aangegeven. Leg het origineel weer op de glasplaat met de af te drukken zijde naar beneden.
4 BEWERKEN-FUNCTIES Spiegelbeeld / Negatief/positief-omkering U kunt een pagina als een spiegel (spiegelbeeld) omkeren of u kunt zwart en wit van een pagina omkeren (negatief/ positief-omkering). Spiegelbeeld 112 Negatief/positief-omkering 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [BEWERKEN] in het menu BEWERKEN. 4 Selecteer [SPIEGEL] of [NEG/POS] en druk vervolgens op [OK].
4 BEWERKEN-FUNCTIES XY-zoom U kunt de reproductiefactor zowel in verticale als in horizontale richting afzonderlijk wijzigen. Deze functie heet “XY-zoom”. 100% 200% 100% 200% De reproductiefactor kan worden ingesteld van 25 tot 400%. In de volgende gevallen is dit bereik echter 25 tot 200%. y Wanneer de modus voor originelen KLEURENDOCOUMENT is y Wanneer het origineel op het automatische documentinvoersysteem (optie) is geplaatst 1 Vul de papierlade(n) met papier. 2 Plaats de originelen.
4 BEWERKEN-FUNCTIES Kaftblad U kunt een speciale papiersoort zoals gekleurd papier voor het voorkaft of het achterkaft toevoegen. Deze functie heet “kaftblad”. In de kaftbladen-functie kunt u selecteren of u het voor- of achterkaft wel of niet wilt afdrukken zoals aangegeven in de onderstaande tabel. Klep voorzijde Modus Achterkaft Omschrijving Modus Omschrijving NEE Hiermee wordt geen vel als voorkaft toegevoegd. NEE Hiermee wordt geen vel als achterkaft toegevoegd.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 5 Selecteer de voor- en achterkaftinstellingen en druk vervolgens op [OK]. Er kan alleen [2 GEKOPIEERD] voor de voor- of achterkaft gekozen worden wanneer [1->2 DUBBELZIJDIG] of [2->2 DUBBELZIJDIG] ingesteld is voor de dubbelzijdige afdrukmodus in het basismenu. 6 Druk op het tabblad [BASIS] voor de weergave van het menu BASIS. Selecteer vervolgens een papierlade waarin normaal papier is geplaatst (niet die voor de kaftbladen).
4 BEWERKEN-FUNCTIES Invoegvel U kunt een speciale papiersoort zoals gekleurd papier bij de gewenste pagina invoegen. Deze functie heet “invoegvel”. U kunt maximaal 2 soorten vellen voor in totaal 50 pagina's invoegen. De stand invoegen speciaal tussenlegvel heeft de volgende 2 mogelijkheden: 2 3 4 RE P 20 ORT 03 RE P 20 ORT 03 4 3 2 1 1 KOPIE: Voegt een gekopieerd vel in plaats van de aangegeven pagina in. 3 2 1 BLANCO: Voegt een leeg vel vóór de aangegeven pagina in.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 5 Selecteer [AFDRUK] of [BLANK]. 6 Selecteer de pagina waarbij het invoegvel wordt ingevoegd. 1) Selecteer het soort invoegvel ([INVOEGLADE 1] of [INVOEGLADE 2]). 2) Toets paginanummers (1 tot 1000) in waar de invoegvellen zullen worden ingevoegd en druk vervolgens op [SET]. Herhaal stap 1) en 2) indien u invoegvellen bij meer dan één pagina wilt invoegen. 3) Druk op [OK] nadat u de paginanummers hebt ingetoetst.
4 BEWERKEN-FUNCTIES 8 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel. Als de originelen op het automatische documentinvoersysteem (optie) zijn geplaatst, begint het scannen en kopiëren. Voer na het plaatsen op de glasplaat voor originelen stap 9 en 10 uit. 9 Plaats het volgende origineel en druk vervolgens op [VLGND AFDR] op het aanraakscherm of op de [START]-toets op het bedieningspaneel.
4 BEWERKEN-FUNCTIES Tijdstempel U kunt de datum en de tijd op het kopieerpapier afdrukken. Onderaan op een staande afdruk Bovenaan op een liggende afdruk MM.DD.YYYY 14:54 MM.DD.YYYY 14:54 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [TIJDSTEMPEL] in het menu BEWERKEN. 4 Selecteer de richting en de plaats van de tijdstempel. 5 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel.
4 BEWERKEN-FUNCTIES Paginanummer U kunt een paginanummer op het kopieerpapier afdrukken. Middenonder op een staande afdruk Rechtsboven op een liggende afdruk 1 2 3 1 2 3 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [PAG. NUMMER] in het menu BEWERKEN. 4 Selecteer de richting en de plaats van een paginanummer. 1) Selecteer de richting ([KORTE ZIJDE] of [LANGE ZIJDE]). 2) Selecteer de plaats ([TOP LINKS], [TOP MIDDEN], enz.).
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 5 Geef de pagina op waarop de nummering moet beginnen. 6 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel. 1) Toets het paginanummer in. 2) Druk op [OK].
4 BEWERKEN-FUNCTIES Taakopbouw U kunt meerdere stapels originelen waarvan de instellingen verschillend zijn, scannen en daarna in één keer kopiëren of opslaan. Deze functie heet “taakopbouw”. Bijvoorbeeld tekstfragmenten (in de TEKST-stand) en foto's in tijdschriften (in de FOTO-stand) in A3-formaat en foto's in A4-formaat kunnen met de optimale instelling voor elk origineel worden gescand en in één keer worden gekopieerd. y Er kunnen maximaal 1000 pagina's originelen in één keer worden gekopieerd.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 2 Druk op [OK]. Taakopbouw is nu ingesteld en de onderstaande melding verschijnt. 3 Plaats de eerste stapel originelen en selecteer daarna de instellingen. y Denk eraan dat bij het plaatsen van het origineel op de glasplaat 1 pagina overeenkomt met 1 taak. y Zie voor het plaatsen van originelen met verschillende formaten op het automatische documentinvoersysteem (optie): P.
4 BEWERKEN-FUNCTIES 4 Druk op de [START]-toets op het bedieningspaneel. 5 Plaats de volgende stapel originelen en selecteer daarna de instellingen. Het scannen begint. Wanneer het scannen van alle originelen is voltooid, verschijnt de onderstaande melding. Herhaal stap 4 en 5 totdat alle gewenste pagina's zijn gescand. Indien u geen instellingen wijzigt, zijn die voor de laatste taak van toepassing. 6 Wanneer het scannen van alle originelen is voltooid, wijzigt u zo nodig het aantal afdruksets.
4 BEWERKEN-FUNCTIES Beeldrichting Wanneer u enkelzijdige staande originelen naar dubbelzijdige afdruk kopieert terwijl deze in liggende richting worden geplaatst, zijn de gekopieerde pagina's normaal gesproken “naar boven geopend”. Met deze functie kan dit worden gewijzigd in “naar links geopend”. Deze functie heet “beeldrichting”.
4 BEWERKEN-FUNCTIES 5 Druk op [OK]. Beeldrichting is nu ingesteld. 6 126 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel.
4 BEWERKEN-FUNCTIES Boek - kalender Met betrekking tot de richting van originelen of gekopieerde beelden wordt “naar links geopend” “boek” en “naar boven geopend” “kalender” genoemd. Met deze functie kunt u dubbelzijdige originelen naar dubbelzijdige afdruk kopiëren waarbij alleen de achterzijde van de gekopieerde pagina 180° wordt gedraaid zodat u “boek” originelen naar “kalender” kunt kopiëren en omgekeerd. 1 Vul de papierlade(n) met papier. 2 Plaats de originelen.
4 BEWERKEN-FUNCTIES ADF -> SADF U kunt de invoermodus bij gebruik van het automatische documentinvoersysteem (optie) van “automatisch documentinvoersysteem (ADF)” naar “enkelvoudige invoer (SADF)” omschakelen. De papierinvoermodus heeft de volgende 2 functies: ADF (continue invoer): Continue invoer van originelen bij het indrukken van de [START]-toets op het bedieningspaneel terwijl originelen op het automatische documentinvoersysteem (optie) worden geplaatst.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 5 Plaats de originelen vel voor vel op het automatische documentinvoersysteem (optie). Het origineel wordt automatisch in het automatische documentinvoersysteem (optie) getrokken, waarna het onderstaande menu verschijnt. Herhaal stap 5 voor een volgend origineel. Het geplaatste origineel wordt automatisch in het automatische documentinvoersysteem (optie) getrokken, zelfs al drukt u niet op [VLGND AFDR] op het aanraakscherm.
4 BEWERKEN-FUNCTIES Geen blanco pagina U kunt blanco pagina's van de gescande originelen verwijderen voordat het kopiëren begint. Deze functie heet “geen blanco pagina”. 1 5 3 1 3 6 5 6 y Deze functie detecteert blanco pagina's van de onderstaande originelen mogelijk niet op de juiste wijze: - Halftoon-originelen - Originelen met bijna blanco pagina's (bijv.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 5 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel. Het scannen en kopiëren begint. Er verschijnt gedurende ca. 5 seconden een melding met het aantal blanco pagina's.
4 BEWERKEN-FUNCTIES Buitenkant wissen U kunt een schaduwachtig donker gedeelte aan de buitenzijde van het gekopieerde beeld wit maken; deze 'schaduw' komt door de tussenruimte tussen de glasplaat voor originelen en de witte plaat. Deze functie heet “buitenkant wissen”. Dit is handig wanneer u dikke originelen zoals boekjes op de glasplaat voor originelen plaatst.
4 BEWERKEN-FUNCTIES 4.BEWERKEN-FUNCTIES 4 Stel “wis randen” in. 1) Druk op [AAN]. 2) Stel de breedte van de rand rondom het origineel naar wens in door op of te drukken. Wanneer u naar de zijde instelt, wordt het gebied dat als niet tot het origineel behorend moet worden gedetecteerd verbreed. Wanneer u naar de zijde instelt, wordt het gebied dat als niet tot het origineel behorend moet worden gedetecteerd versmald. 3) Druk op [OK]. 5 Leg het origineel op de glasplaat.
5. BEELDCORRECTIE Dit hoofdstuk beschrijft de functies voor beeldcorrectie van deze apparatuur. Weergave menu BEELD....................................................................................................... 136 Gebruik van de functies voor beeldcorrectie .................................................................... 137 Achtergrondinstelling ..........................................................................................................................................
5 BEELDCORRECTIE Weergave menu BEELD U kunt het menu BEELD oproepen door op het tabblad [BEELD] op het aanraakscherm te drukken wanneer u de verschillende functies voor beeldcorrectie wilt gebruiken.
5 BEELDCORRECTIE Gebruik van de functies voor beeldcorrectie Achtergrondinstelling Deze functie dient voor de aanpassing van de densiteit van de achtergrond van het origineel. Hiermee wordt voorkomen dat de achterzijde van een dubbelzijdig origineel op de voorzijde ervan zichtbaar wordt. Vóór Achter Aangepast voor een lichtere achtergrond Niet aangepast Deze functie kan niet samen met de automatische densiteitaanpassing worden gebruikt. P.59 “Densiteitaanpassing” 1 Druk op [ACHTERG.
5 BEELDCORRECTIE Scherpte Deze functie dient voor het verscherpen of vervagen van de contouren van het beeld. 1 Druk op [SCHERPTE] in het menu BEELD. 2 Druk op [ZACHT] of [SCHERP] voor de instelling van de scherpte en druk vervolgens op [OK]. Wanneer het scherpteniveau naar de [ZACHT] zijde wordt ingesteld, worden de gevlamde randen op de afgedrukte foto's enz. verzacht. Bij de instelling naar de [SCHERP] zijde worden de letters en dunne lijnen scherper.
6. TEMPLATES In dit hoofdstuk wordt het gebruik van templates beschreven. Templates.............................................................................................................................. 140 Weergave templatemenu ...................................................................................................................................140 Gebruik van “Praktische templates” .......................................................................................................
6 TEMPLATES Templates U kunt een template aanmaken met meerdere functies die vaak worden gebruikt zodat deze desgewenst kan worden opgevraagd en u niet telkens ingewikkelde instellingen hoeft uit te voeren. Templates kunnen worden gebruikt bij het kopiëren, scannen en versturen van een fax. Fax-functies zijn alleen beschikbaar als de fax-eenheid (optie) is geïnstalleerd. 2011.5.5 = 1 1 + 2011.5.5 + 2011.5.5 2011.5.
6 TEMPLATES 6.TEMPLATES Gebruik van “Praktische templates” Dit multifunctionele systeem beschikt over 12 standaardtemplates, die direct kunnen worden gebruikt. Deze zijn vastgelegd onder groepsnummer 001 “Praktische templates”. Voor het oproepen ervan zie: P.
6 TEMPLATES Templates met e-Filing-functies Toets Functie *1 Modus voor originelen: TEKST/FOTO Enkelzijdig/dubbelzijdig: 1 -> 1 ENKELZIJDIG Opslagmethode: opgeslagen in de e-Filing-box (openbare box) Geen afdrukfunctie Modus voor originelen: TEKST/FOTO Enkelzijdig/dubbelzijdig: 2 -> 1 DUBBELZ. NAAR 2 ENKELZ.
6 TEMPLATES Templates vastleggen Templates moeten worden vastgelegd in de “openbare templategroep” of in de “privé-groepen”. U kunt een wachtwoord instellen om het gebruik van vastgelegde templates te beperken. Openbare templategroep: Dit is de standaardinstelling. Templates in deze groep kunnen door iedereen worden gebruikt. Het is handig meerdere combinaties van functies die vaak in het gehele kantoor of in een afdeling worden gebruikt vast te leggen.
6 TEMPLATES 4 Druk op [WACHTWOORD]. Het toetsenbord op het scherm verschijnt. 5 Geef het Admin-wachtwoord op met behulp van het toetsenbord op het scherm of de numerieke toetsen. Druk daarna op [OK]. 6 Selecteer een template. 1) Druk op een lege toets. 2) Druk op [BEWAREN]. Tussen menu's schakelen Druk op 144 of Templates vastleggen .
6 TEMPLATES 6.TEMPLATES 7 Voer de benodigde gegevens over de template in. NAAM 1 & 2: Toets de naam van de template in. NAAM 1 verschijnt boven de templatetoets en NAAM 2 verschijnt eronder. Voer ten minste een ervan in. Wanneer u op een van beide drukt, verschijnt het toetsenbord op het scherm. Toets maximaal 11 tekens in. GEBR.NAAM: Toets zo nodig de naam van de template-eigenaar in. Wanneer u erop drukt, verschijnt het toetsenbord op het scherm. Toets maximaal 30 tekens in.
6 TEMPLATES Zelfs wanneer de automatische startfunctie is ingeschakeld, moet u in de volgende gevallen de gebruikersnaam en het wachtwoord opgeven voor het oproepen van de template. Informeer bij uw beheerder voor meer informatie over de gebruikersauthenticatie voor Scannen naar e-mailbericht en de gebruikersbeheerfunctie.
6 TEMPLATES 6.TEMPLATES 3 Voer de benodigde gegevens over de groep in. NAAM: Toets de naam van de groep in. Wanneer u erop drukt, verschijnt het toetsenbord op het scherm. Toets maximaal 20 tekens in. Zorg ervoor dat deze wordt ingevoerd. GEBR.NAAM: Toets zo nodig de naam van de groepseigenaar in. Wanneer u erop drukt, verschijnt het toetsenbord op het scherm. Toets maximaal 30 tekens in.
6 TEMPLATES Templates in een privé-groep vastleggen 1 Stel alle benodigde functies in. 2 Druk op [TEMPLATE] op het aanraakscherm. Voorbeeld: Bewerken-functie – beeld verplaatsen, reproductiefactor – 90%, aantal afdruksets –10 Het templatemenu verschijnt. 3 Selecteer de gewenste groep. 1) Druk op het tabblad [REGISTRATIE]. 2) Selecteer de gewenste groep door op de toets ervan te drukken of het groepsnummer ervan (3 cijfers) in te toetsen. 3) Druk op [OPENEN].
6 TEMPLATES 6.TEMPLATES 4 Toets het wachtwoord voor de geselecteerde groep in. (Als er geen wachtwoord is ingesteld, gaat u verder met stap 5.) 1) Druk op [WACHTWOORD] en toets het wachtwoord in door middel van de toetsen op het aanraakscherm of de numerieke toetsen op het bedieningspaneel. 2) Druk op [OK]. 5 Leg een template vast zoals beschreven in stap 6 en 7 op openbare templategroep vastleggen”. P.
6 TEMPLATES Templates oproepen Wanneer u een template oproept, worden de daarin ingestelde functies automatisch geactiveerd. Als de automatische startfunctie is ingeschakeld, start het multifunctionele systeem de uitvoering van elke functie automatisch wanneer u de toets voor de betreffende template indrukt. 1 Vul de papierlade(n) met papier. 2 Plaats de originelen. 3 Druk op [TEMPLATE] op het aanraakscherm. Het templatemenu verschijnt.
6 TEMPLATES 6.TEMPLATES 5 Toets het wachtwoord in wanneer u de privé-groep heeft geselecteerd. (Als er geen wachtwoord is ingesteld, gaat u verder met stap 6.) 1) Druk op [WACHTWOORD] en toets het wachtwoord in door middel van de toetsen op het aanraakscherm of de numerieke toetsen op het bedieningspaneel. 2) Druk op [OK]. 6 Druk op de toets van de gewenste template. Tussen menu's schakelen Druk op of . Templates met ingeschakelde automatische startfunctie kunnen worden aangeduid met .
6 TEMPLATES 8 Controleer of “Bijwerken template (SJABLOON instelling)” wordt weergegeven op het aanraakscherm. De melding wordt ca. 3 seconden weergegeven. 9 152 Selecteer naargelang nodig andere kopieerinstellingen en druk vervolgens op de [START]-toets op het bedieningspaneel.
6 TEMPLATES Gegevens wijzigen U kunt de gegevens wijzigen van reeds vastgelegde templates of privé-groepen zoals templatenaam, gebruikersnaam, wachtwoord en instelling van de automatische startfunctie. De gegevens van de openbare templategroep kunnen worden gewijzigd vanuit het TopAccess-menu, maar niet via het bedieningspaneel. Voor de wijziging ervan vanuit het TopAccess-menu zie de TopAccess Guide. Gegevens van privé-groep wijzigen 1 Selecteer de gewenste groep in het templatemenu.
6 TEMPLATES Templategegevens wijzigen 1 Selecteer in het templatemenu de groep waarin de gewenste template is vastgelegd. 1) Druk op het tabblad [REGISTRATIE]. 2) Selecteer de gewenste groep door op de toets ervan te drukken of het groepsnummer ervan (3 cijfers) in te toetsen. 3) Druk op [OPENEN]. Tussen menu's schakelen Druk op 2 154 of . Toets het wachtwoord als volgt in en druk vervolgens op [OK].
6 TEMPLATES 6.TEMPLATES 3 Selecteer de gewenste template. 1) Druk op de toets van de betreffende template. 2) Druk op [BEWERKEN]. Tussen menu's schakelen Druk op 4 of . Toets het wachtwoord voor de geselecteerde template in. (Als er geen wachtwoord is ingesteld, gaat u verder met stap 5.) 1) Druk op [WACHTWOORD] en toets het wachtwoord in door middel van de toetsen op het aanraakscherm of de numerieke toetsen op het bedieningspaneel. 2) Druk op [OK].
6 TEMPLATES Groepen of templates verwijderen U kunt privé-groepen of templates die niet meer worden gebruikt verwijderen. Als een privé-groep wordt verwijderd, gebeurt dit ook met alle templates in deze groep. De openbare templategroep kan niet worden verwijderd. Privé-groepen verwijderen 1 Selecteer de gewenste privé-groep in het templatemenu. 1) Druk op het tabblad [REGISTRATIE]. 2) Selecteer de gewenste groep door op de toets ervan te drukken of het groepsnummer ervan (3 cijfers) in te toetsen.
6 TEMPLATES 6.TEMPLATES 3 Druk op [WISSEN]. De privé-groep is nu verwijderd.
6 TEMPLATES Templates verwijderen 1 Selecteer in het templatemenu de groep waarin de gewenste template is vastgelegd. 1) Druk op het tabblad [REGISTRATIE]. 2) Selecteer de gewenste groep door op de toets ervan te drukken of het groepsnummer ervan (3 cijfers) in te toetsen. 3) Druk op [OPENEN]. Tussen menu's schakelen Druk op 2 158 of . Toets het wachtwoord als volgt in en druk vervolgens op [OK].
6 TEMPLATES 6.TEMPLATES 3 Selecteer de gewenste template. 1) Druk op de toets van de gewenste template. 2) Druk op [VERWIJDER]. Tussen menu's schakelen Druk op 4 of . Toets het wachtwoord voor de geselecteerde template in. (Als er geen wachtwoord is ingesteld, gaat u verder met stap 5.) 1) Druk op [WACHTWOORD] en toets het wachtwoord in door middel van de toetsen op het aanraakscherm of de numerieke toetsen op het bedieningspaneel. 2) Druk op [OK]. 5 Druk op [WISSEN]. De template is nu verwijderd.
7. TAAKSTATUS BEVESTIGEN Dit hoofdstuk beschrijft hoe de verwerkingsstatus bevestigd wordt en de historie van uitgevoerde kopieertaken. Bevestiging afdruktaakstatus ............................................................................................. 162 Taken in uitvoering of in de wachtrij bevestigen .................................................................................................162 Taakgeschiedenis bevestigen ....................................................................
7 TAAKSTATUS BEVESTIGEN Bevestiging afdruktaakstatus U kunt taken die in uitvoering zijn of zich in de wachtrij bevinden op het aanraakscherm bevestigen. U kunt taken in de wachtrij ook annuleren, onderbreken of hervatten alsmede de volgorde ervan wijzigen. Het is bovendien mogelijk de geschiedenis van uitgevoerde afdruktaken, de status van papierladen en de hoeveelheid resterende toner in de cartridges te bevestigen.
7 TAAKSTATUS BEVESTIGEN 7.TAAKSTATUS BEVESTIGEN Taken annuleren U kunt taken die niet meer hoeven te worden uitgevoerd annuleren. 1 Selecteer de gewenste taak in de afdruktakenlijst en druk vervolgens op [VERWIJDER]. Het is mogelijk meer dan één taak te selecteren. 2 Druk op [VERWIJDER]. De taak is nu verwijderd.
7 TAAKSTATUS BEVESTIGEN Taken onderbreken Taken met status “Wacht”, kunnen in de wachtrij worden vastgehouden (onderbreken). Selecteer de gewenste taak in de afdruktakenlijst en druk vervolgens op [PAUZE]. De taak is nu gepauzeerd. De onderbroken taak wordt niet afgedrukt, zelfs niet wanneer die aan de beurt komt. Het afdrukken van de volgende taak begint. Onderbroken taak hervatten Selecteer de gewenste taak en druk vervolgens op [HERVAT].
7 TAAKSTATUS BEVESTIGEN 7.TAAKSTATUS BEVESTIGEN Taken verplaatsen U kunt de volgorde van de taken in de wachtrij wijzigen door deze in de lijst te verplaatsen. U kunt alleen taken verplaatsen van en naar die waarvan de status “Wacht” is. 1 Selecteer de gewenste taak in de afdruktakenlijst en druk vervolgens op [VERPLAATS]. 2 Selecteer de positie waarheen u de taak wilt verplaatsen. (Deze wordt onder de geselecteerde taak geplaatst.
7 TAAKSTATUS BEVESTIGEN Bevestiging van de informatie van een overgeslagen taak Het kan zijn dat er geen afdruktaken uitgevoerd kunnen worden omdat het opgegeven papier op is of de nietjes op zijn enz. Deze zullen onderbroken worden en de volgende taak zal worden uitgevoerd (functie Taak overslaan). Kijk op het aanraakscherm hoe u de onderbroken taken kunt herstellen. 1 Selecteer de overgeslagen taak in de afdruktakenlijst en druk op [HERSTELINFORMATIE].
7 TAAKSTATUS BEVESTIGEN 7.TAAKSTATUS BEVESTIGEN Taakgeschiedenis bevestigen U kunt de geschiedenis van de uitgevoerde afdruktaken op het aanraakscherm bevestigen. 1 Druk op [TAAKSTATUS] op het aanraakscherm. 2 Druk op het tabblad [LOG]. 3 Druk op [AFDRUKKEN]. Het afdruklogboek verschijnt. Kopieertaken verschijnen in het afdruklogboek alsmede afdruktaken.
7 TAAKSTATUS BEVESTIGEN Papierladen bevestigen U kunt de instelling van papierformaat en -soort of het aantal resterende vellen in de papierladen bevestigen. Tijdens het afdrukken kunt u bevestigen welke papierlade voor de papierinvoer zorgt. 1 Druk op [TAAKSTATUS] op het aanraakscherm. 2 Druk op het tabblad [PAPIER]. Tijdens het afdrukken is de toets voor de papierlade waaruit papier wordt aangevoerd gemarkeerd. Druk op [SLUITEN] om de bevestiging te beëindigen.
7 TAAKSTATUS BEVESTIGEN 7.TAAKSTATUS BEVESTIGEN Hoeveelheid resterende toner bevestigen U kunt de hoeveelheid toner die nog ongeveer in de cartridge aanwezig is bevestigen. 1 Druk op [TAAKSTATUS] op het aanraakscherm. 2 Druk op het tabblad [TONER]. Druk op [SLUITEN] om de bevestiging te beëindigen. Er wordt teruggekeerd naar het menu dat werd weergegeven vóór het drukken op [TAAKSTATUS].
8. OVERIGE INFORMATIE Continue kopieersnelheid ................................................................................................... 172 Combinatiematrix kopieerfunctie ....................................................................................... 174 Combinatiematrix 1/2 .........................................................................................................................................174 Combinatiematrix 2/2 .....................................................
8 OVERIGE INFORMATIE Continue kopieersnelheid Kopieersnelheden zijn afhankelijk van de wijze waarop originelen op de glasplaat worden geplaatst en er continu enkelzijdige afdrukken worden gemaakt met een reproductiefactor van 100% in de stand sorteren-uit (eenheid: vel/ minuut). e-STUDIO206L Papierformaat A4, A5-R, B5, LT, ST-R, 8,5" SQ A4-R, B5-R, LT-R B4, FOLIO, LG, COMP, 13" LG A3, LD Toevoermagazijn Papiersoort NORMAAL DIK1 DIK2 Papierlade 20.3 19.7 — DIK3 — Handinvoerbak 20.3 19.7 19.
8 OVERIGE INFORMATIE 8.OVERIGE INFORMATIE e-STUDIO456 Papierformaat A4, A5-R, B5, LT, ST-R, 8,5" SQ A4-R, B5-R, LT-R B4, FOLIO, LG, COMP, 13" LG A3, LD Toevoermagazijn Papiersoort NORMAAL DIK1 DIK2 DIK3 Papierlade 45.3 43.4 — — Handinvoerbak 45.3 43.4 43.4 43.4 Papierlade 35.0 33.9 — — Handinvoerbak 35.0 33.9 33.9 33.9 Papierlade 29.5 28.7 — — Handinvoerbak 29.5 28.7 28.7 28.7 Papierlade 25.4 24.8 — — Handinvoerbak 25.4 24.8 24.8 24.
174 Ja Ja Combinatiematrix kopieerfunctie Ja Nr. Ja Ja Nr. Ja Ja Brochure sorteren & uitvouwblad Perforatie Rughechten Roteren en sorteren Brochure sorteren Nr. Ja Nr. Ja Nr. Nieten en sorteren Ja Ja Ja Groeperen Nr.
*1 Nr. Ja *1 Nr. Ja Nr. Nr. Nr. Ja Ja Ja Ja Nr. Nr. Nr. Nr. Nr. Nr. Ja Nr. Nr. Ja Ja Ja Ja Nr. Nr. Nr. Nr. Ja Nr. Nr. Boek - 2 Sorteren uit / nieten uit Sorteren Groeperen Nieten en sorteren Brochure sorteren Brochure & rughechten Brochure sorteren & uitvouwblad Perforatie Rughechten Roteren en sorteren Ja *3 1 - 2 Dubbelzijdig Nr.
TREFWOORDENREGISTER Taal 2IN1/4IN1 ................................................................104 [2-ZIJDIG] ...................................................................8 A A/B-formaat ...............................................................11 Aanpassing dichtheid .......................................... 52, 59 Aanraakscherm ...........................................................8 Aantal afdrukken .............................................
Finisher voor rughechten ......................................66 naam van elk onderdeel .......................................68 [FINISHING] ................................................................8 FOTO .......................................................................58 FTP ..........................................................................91 FTPS ........................................................................91 Toets [FUNCTION CLEAR] ............................
Roteren en sorteren ............................................ 66, 73 Rughechten ........................................................ 66, 77 S SADF .....................................................................128 SCHERPTE .............................................................138 SMB .........................................................................92 Sorteren ............................................................. 66, 71 Sorteren uit nieten uit ............................
180 TREFWOORDENREGISTER
e-STUDIO256SE/306SE/356SE/456SE
MULTIFUNCTIONELE DIGITALE SYSTEMEN Kopieerhandleiding 2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN Ver01 2012-02 ©2011 TOSHIBA TEC CORPORATION Alle rechten voorbehouden