User’s Manual A100 PMR300128EN0 PMR300128EN0 Choose freedom. Choose freedom. computers.toshiba-europe.com computers.toshiba-europe.
TOSHIBA A100 Copyright © 2006 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
TOSHIBA A100 Trademarks IBM is a registered trademark, and IBM PC and PS/2 are trademarks of International Business Machines Corporation. Intel, Intel SpeedStep and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries/regions. Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak. Memory Stick is a registered trademark and i.LINK is a trademark of SonyCorporation.
TOSHIBA A100 Safety Instructions Use the following safety guidelines to help protect yourself and your computer. When Using Your Computer Do not operate your portable computer for an extended period of time with the base resting directly on your body. With extended operation, heat can potentially build up in the base. Allowing sustained contact with the skin could cause discomfort or, eventually, a burn. ■ Do not attempt to service the computer yourself. Always follow installation instructions closely.
TOSHIBA A100 EU Declaration of Conformity TOSHIBA declares, that the product: Toshiba A100 (PSAA8*/PSAA9*) conforms to the following Standards: This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 89/ 336/EEC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 99/5/EEC in case of implemented telecommunication acces
TOSHIBA A100 Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
TOSHIBA A100 The drive with the label above is certified by the manufacturer that the drive complies with the requirement for laser product on the date of manufacturing pursuant to article 21 of Code of Federal Regulations by the United States of America, Department of Health & Human Services, Food and Drug Administration. In other countries, the drive is certified to comply with the requirement pursant to IEC 825 and EN60825 on class 1 laser product.
TOSHIBA A100 Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.
Preface Congratulations on your purchase of the TOSHIBA A100 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TOSHIBA A100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
TOSHIBA A100 Manual contents This manual is composed of nine chapters, five appendixes, a glossary, and an index. Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and options. Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function. Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.
TOSHIBA A100 Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Abbreviations On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary. Icons Icons identify ports, dials, and other parts of your computer.
TOSHIBA A100 Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read. A note is a hint or advice that helps you make best use of your equipment.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury, damage to the computer or impared performance. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
TOSHIBA A100 PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer opreation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mo-bile phone in use.
TOSHIBA A100 Wireless LAN/Atheros For 802.11a, b and g The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed.
TOSHIBA A100 LCD Brightness and Eye Strain Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes. Graphics Processing Unit ("GPU") Performance Disclaimer The graphics processing unit ("GPU") performance may vary depending on product model, design configuration, applications, power management settings and features utilized.
Table of Contents Preface General Precautions Chapter 1 Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10 Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 Options . . . .
TOSHIBA A100 Chapter 4 Operating Basics Using the Touch Pad/Dual Mode Pad . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Dual Mode Pad Button function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Using the USB diskette drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Using optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Removing discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOSHIBA A100 Express Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Multiple Digital Media Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Additional battery pack (6 Cell, 9 Cell and 12 Cell) . . . . . . . . . . . . . . 8-9 Additional AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not pre- installed by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Windows XP Professional/Home Edition Service Pack 2 The following software is preinstalled: ■ Microsoft® Windows XP Home Edition or Professional Edition ■ Modem Driver ■ Network Driver ■ Wireless LAN driver (Can be used only for Wireless LAN models) ■ Bluetooth Driver (Can be used only for Bluetooth models) ■ Display Drivers for Windows ■ Sound Driver for Windows ■ Pointing Device Driver ■ DVD Video Player ■ TOSHIBA Utilities ■ TOSHIBA Power Saver ■ TOSHIBA User’s Manual ■ TOSHIBA Ass
Introduction Product Recovery Media and Addtional Software ■ Product Recovery ■ Express Media Player Recovery CD * Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple-mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability.
Introduction Disks User’s Manual Hard disk drive The computer has an integrated, 2 1/2" hard disk drive (HDD) for nonvolatile storage of data and software. It comes in the following sizes. 40 GB (37.26 billion bytes) 60 GB (55.89 billion bytes) 80 GB (74.52 billion bytes) 100 GB (93.15 billion bytes) 120 GB (111.78 billion bytes) Diskette drive (optional) 3 1/2" 1.44-megabyte or 720-kilobyte connects to the USB port. (Windows® XP does not support 720-kilobyte diskettes.
Introduction CD-RW/ DVD-ROM drive User’s Manual Some models are equipped with a full-size, CD-RW/ DVD-ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 24 speed. See Chapter 4, Operating Basics, for details.
Introduction DVD Super Multi (+-R Double Layer) drive Some models are equipped with a full-size DVD Super Multi (+- R Double Layer) drive module that lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed, CD-RW at up to 10 speed, DVD-R at up to 8 speed and DVD-RW at maximum 4 speed and DVDRAM at maximum 5 speed.
Introduction Keyboard Built-in 85 keys or 86 keys, compatible with IBM® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. See Chapter 5, The Keyboard, for details. Pointing Device Built-in A Touch Pad/Dual Mode Pad and control buttons in the palm rest enable control of the on-screen pointer. Battery pack The computer is powered by one rechargeable lithiumion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar.
Introduction Slots PC card A PC card slot accommodates: One 5 mm Type II card Refer to Chapter 8, Optional Devices, for details Multiple Digital Media Card This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use flash memory (SD/MS/MS Pro/MMC/xD memory cards). (Provided with some models) Express card This slot allows you to install a Express Card™/34 or Express Card™/54 to expand functionality.
Introduction User’s Manual Wireless LAN Some computers in this series are equipped with a Wireless LAN mini card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B and G), and Turbo Mode. Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s (Revision A/B, B/G, A/B/G combo type).
Introduction Security Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object. Software Operating System Windows® XP Professional or Home Edition is available. Refer to the preinstalled software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities section in this chapter.
Introduction User’s Manual Instant security A hot key function blanks the screen and disables the computer providing data security. Intelligent power supply A microprocessor in the computer’s intelligent power supply detects the battery’s charge and calculates the remaining battery capacity. It also protects electronic components from abnormal conditions, such as voltage overload from an AC adaptor. You can monitor remaining battery capacity. Use the Battery remaining item in TOSHIBA Power Saver.
Introduction Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA TOSHIBA Assist is a graphical user interface that Assist provides easy access to help and services. User’s Manual TOSHIBA Power Saver To access this power savings management program, click the Control Pane then Performance and maintenace and select the TOSHIBA Power Saver icon.
Introduction TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks.
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: User’s Manual Memory expansion Two memory slots are available for installing 256 MB or 512 MB or 1024 MB memory modules. The modules are PC4200, 200-pin, SO Dual In-line (SO-DIMM).
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The figure below shows the computer’s front with its display panel in the closed position familiar with each component before you operate the computer. An asterisk * indicates a optional feature that is dependant on the model purchased.
The Grand Tour Microphone jack A standard 3.5 mm mini microphone jack enables connection of a monaural microphone or other device for audio input. Headphone jack A standard 3.5 mm mini headphone jack enables connection of a stereo headphone (16 ohm minimum) or other device for audio output. When you connect headphones, the internal speaker is automatically disabled. Infrared port This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.
The Grand Tour Video-out jack Plug a 4-pin S-Video connector into this jack. i.LINK (IEEE 1394) Port Connect an external device, such as a digital video camera to this port for high-speed data transfer. Some models are equipped with a i.LINK port. (Provided with some models) When multiple IEEE1394 devices are connected to a PC, the devices may not correctly be identified.
The Grand Tour Right side The figure below shows the computer’s right side. Wireless communication switch * USB Ports Security lock slot Optical Media Drive Modem jack The right side of the computer Universal Serial Bus Ports The two Universal Serial Bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. (The ports also support USB 1.1) Keep foreign objects out of the USB connectors.
The Grand Tour Back side The figure below shows the computer’s back side. USB Ports LAN jack DC IN 15V The computer’s back side Universal Serial Bus Ports The two Universal Serial Bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. (The ports also support USB 1.1) Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry.
The Grand Tour Underside The figure below shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery Pack Lock Battery pack Battery Release Latch Memory module cover The underside of the computer User’s Manual Battery pack The battery pack powers the computer when the AC adaptor is not connected. The Batteries section in Chapter 6, Power and Power-Up Modes, describes how to access the battery pack.
The Grand Tour Front with the display open The figure below shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle.
The Grand Tour Touch Pad Control Buttons Function like the left and right buttons on an external mouse. Power Button Press the power button to turn the computer’s power on and off. The Power button LED indicates the status. AV Buttons Some models are equipped with some of the following buttons. Available for use: Internet, CD/DVD, Play/Pause, Stop, Previous, Next. These buttons allow you to manage Audio/Video, run applications and access utilities.
The Grand Tour System indicators The figure below shows the system indicators, which light when various computer operations are in progress. Multiple Digital Media card slot * Disk Main battery Power DC IN Systems indicators User’s Manual DC IN The DC IN indicator glows blue when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes amber. Power The Power indicator glows blue when the computer is on.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers. Numeric mode Arrow mode Keypad overlay indicators Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (white labeled keys) as cursor keys.
The Grand Tour USB diskette drive A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. Disk-In-Use Indicator Diskette slot Eject button USB diskette drive Disk-In-Use Indicator This indicator lights when the diskette is being accessed. Diskette slot Insert diskette in this slot. Eject button When a diskette is fully seated in the drive, the eject button pops out.
The Grand Tour Optical Media drive CD-RW/DVD-ROM drive, DVD-ROM drive, DVD Super Multi (+-R Double Layer) drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. Region codes for DVD drives and media CD-RW/DVD-ROM, DVD-ROM, DVD Super Multi (+-R Double Layer) drive and media are manufactured according to the specifications of six marketing regions.
The Grand Tour Formats The drives support the following formats: ■ DVD-ROM ■ DVD-Video ■ CD-DA ■ CD-Text ■ Photo CD™ (single/multi-session) ■ CD-ROM Mode 1, Mode 2 ■ CD-ROM x A Mode 2 (Form1, Form2) ■ Enhanced CD (CD-EXTRA) ■ CD-G (Audio CD only) DVD-ROM drive The full- size DVD-ROM drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.
The Grand Tour The read speed is slower at the center of a disc and faster at the outer edge. DVD read 8 speed (maximum) DVD-R write 8 speed (maximum) DVD-RW write 6 speed (maximum) DVD+R write 8 speed (maximum) DVD+RW write 8 speed (maximum) DVD+R DL write 4 speed (maximum) DVD-R DL write 4 speed (maximum) DVD-RAM write 5 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 6 speed (maximum, ultra-speed media) Remote Control Some models are optional provided with a Remote Control.
The Grand Tour Part Names of Remote Control The figure below shows the buttons on the remote control. Refer to the descriptions on the next page of the functions of each button. Express Media Player Button Power On/Off CD/DVD Key CD DVD WinDVD Windows Media Player DVD CD Turns the computer on and off. If the system is On, the behavior of the power button is defined by Power If the system is On, turn the options settings. Express Media Player off.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6, Power and Power-Up Modes for details. The AC adaptor Use of the wrong adaptor could damage your computer.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started Setting up your work space Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
Getting Started Placement of computer Position the computer and peripheral devices to provide comfort and safety. ■ Set the computer on a flat surface at a comfortable height and distance. The display should be no higher than eye level to avoid eye strain. ■ Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices. ■ Allow adequate space behind the computer to let you freely adjust the display.
Getting Started Lighting Proper lighting can improve legibility of the display and reduce eye strain. ■ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ■ Avoid placing the computer in front of bright light that could shine directly in your eyes. ■ If possible, use soft, indirect lighting in your computer work area.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you. When you open the display, hold it with both hands and lift up slowly. Display latch Opening the display panel Turning on the power This section describes how to turn on the power.
Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows® XP Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode, no data is saved and the computer will boot to the operating system’s main screen. 1.
Getting Started Benefits of hibernation The hibernation feature provides the following benefits: ■ Saves data to the hard disk when the computer automatically shuts down because of a low battery. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode.
Getting Started Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Built-in HDD indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Getting Started 3. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility described in the Control Panel. In Windows® XP, open Performance and Maintenance and open TOSHIBA Power Saver. When you turn the power back on, you can continue where you left when you shut down the computer. ■ When the computer is shut down in standby mode, the power indicator glows orange.
Getting Started Restoring the preinstalled software If preinstalled files are damaged, use the Product Recovery Media to restore them. To restore the operating system and all preinstalled software, follow the steps below. Please use the Express Media Player Recovery CD first to reinstall the "Express Media Player" before you reinstall a Windows® operating system. (Depends on configuration) When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.
Getting Started Restoring the operating system To restore the operating system and all pre-installed software, follow the steps below. When you reinstall the Windows® operating system, the hard disk will be reformatted and all data will be lost. 1. Load the Product Recovery Media in the drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3.
Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad/Dual Mode Pad, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Using the Touch Pad/Dual Mode Pad To use the Touch Pad/Dual Mode Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics Touch Pad/Dual Mode Pad Fingerprint Sensor * Touch Pad Control Buttons Touch Pad/Dual Mode Pad and Touch Pad control buttons Dual Mode Pad Button function Some models in this series are provided with a Dual Mode Pad. Mail Button Print Out Config Free Switch Button Volume Application Buttons Dual Mode Pad Button User’s Manual Switch button To switch between Cursor Mode and Button Mode. When you switch to Button Mode, the pad blinks blue.
Operating Basics Print out To send the item in the active window to the printer. Application buttons Three application buttons have default setting. You can assign other functions and programs to button 1 to 3. Please refer to "Properties for Synaptics Dual Mode Pad" for details Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44-megabyte or 720-kilobyte diskettes. Refer to Chapter 2, The Grand Tour, for more information.
Operating Basics Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Click the Safely Remove Hardware icon on the system tray. 3. Click Diskette drive. 4.
Operating Basics b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 1.5 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. Eject Hole Diameter 1.0 mm Manual release with the eject hole 2. Grasp the drawer gently and pull until it is fully opened. Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer.
Operating Basics When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure above. Do not touch the laser lens. Doing so could cause misalignment. Do not keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4.
Operating Basics Removing discs To remove the CD/DVD, follow the steps below and refer to figure below. Do not press the eject button while the computer is accessing the DVD-ROM drive. Wait for the optical media drive indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics AV Button function Some models are provided with a some of the AV buttons described below.
Operating Basics Remote Control Some models are optional provided with a Remote Control. The remote control unit allows you to control some of your computer’s functions from a distant location. Using the Remote control The remote control is designed specifically for this computer. Some application programs may not support remote control functions. Operational range of the remote control Point the remote control at your computer and press a button. The operational angle and distance are described below.
Operating Basics Precautions for use Even if within the effective scope as described above, the remote control may malfunction or not work correctly in the following cases. ■ When an obstacle stands between the infrared receiver window of your computer and the remote controller. ■ When direct sunlight or strong fluorescent light strikes the infrared receiver window. ■ When infrared receiver window or the infrared emission part of the remote controller is dirty.
Operating Basics Installing the batteries 1. Open the battery cover on the back side of the remote controller. Push and remove the battery cover. Opening the battery cover 2. Insert the batteries in place. Be sure to place the batteries with their polarities (+ and -) in the correct position. Inserting the batteries 3. Close the battery cover. Close the cover securely until it clicks.
Operating Basics 2. Replace the batteries. Be sure to place the batteries with their polarities (+ and -) in the correct position. Replacing the batteries 3. Close the battery cover. Close the cover securely until it clicks. Closing the battery cover Installing/Removing Remote Controller This Remote Conroller can be installed in PC Card Slot. Please make the arrow on Remote Controller upward, and install it in PC Card Slot. For details, please refer to PC cards section in Chapter 8, Optional Devices.
Operating Basics Express Media Player Express Media Player is a quick play feature that enables users to perform DVD and CD playback without loading Windows. The availability of the Express Media Player depends on the model of computer you have purchased. Express Media Player offers a 'quick play' feature that enables users to playback CD and DVD content without having to use the main Windows operating system.
Operating Basics Express Media Player (DVD) Usage ■ Express Media Player (DVD) plays the disc according to the way the DVD-Video has been programmed by the producer, hence sometimes it might not work as expected. ■ ( ) might appear on screen during operation. When ( ) is displayed, it means that Express Media Player (DVD) or DVD-Video prohibits that particular operation from being carried out. ■ Please also read the instructions that come with the DVD that you want to play.
Operating Basics Display Language Code Language English English Español Spanish Français French Italiano Italian Nederlands Dutch Português Portuguese Simplified Chinese Traditional Chinese Deutsch German Display Language Keyboard Code Keyboard Code EN1 US English PT1 Portuguese EN2 UK English RU1 Russian ES1 Spanish SV1 Swedish FR1 French TR1 Turkish FR2 CanadianFrench AR1 Arabic IT1 Italian BE1 Belgian IW1 Hebrew DA1 Danish JA1 Japanese DE1 German KO1 Ko
Operating Basics Front panel Computer CD DVD - Fn + F7 Increases the brightness Increases the brightness - Fn + F6 Decreases the brightness Decreases the brightness - 1 Select track 1 Select chapter 1 - 2 Select track 2 Select chapter 2 - 3 Select track 3 Select chapter 3 - 4 Select track 4 Select chapter 4 - 5 Select track 5 Select chapter 5 - 6 Select track 6 Select chapter 6 - 7 Select track 7 Select chapter 7 - 8 Select track 8 Select chapter 8 - 9 Select t
Operating Basics Front panel Computer CD DVD - P Skip by about 10 seconds Skips forwards quickly Space Play or pauses Play or pauses Ctrl + Space Stop Stop K Next track Next chapter L Previous track Previous chapter - Ctrl + R Repeat - - Ctrl + S Shuffle - - D Changes the screen Changes the screen - G - Changes the angle - S - Changes the subtitle - A - Changes the audio channel - T - Select the title - Y - Slow play - F1 Display the keyguide Display t
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite the data. ■ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R TAIYOYUDEN CO., LTD. Mitsui Chemicals Inc. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. The following special media recommended the next manufacturers.
Operating Basics ■ Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel. ■ Start a communication application such as a modem. ■ Apply impact or vibration to the PC. ■ Install, remove or connect external devices, including the following: PC card, USB devices, external display, i.LINK devices, optical digital devices. ■ Open the optical media drive. ■ If the media is poor in quality, dirty or damaged, writing or rewriting errors may occur.
Operating Basics Before writing or rewriting ■ Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM/ +R DL/-R DL disc. ■ However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd.
Operating Basics ■ There are two types of DVD-R discs: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. ■ We can support only format 1 of DVD-R DL. Therefore you can not do the additional writing. If your data is under DVD-R(SL) capacity, we suggest to use DVD-R(SL) media. ■ You can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge. You cannot use a disc with a 2.
Operating Basics When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ RW, DVD-R/-R DL/-RW/-RAM or DVD+R/+R DL/+RW disc. ■ Do not perform any of the following actions: ■ Change users in the Windows XP operating system. ■ Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel. ■ Start a communication application such as a modem. ■ Apply impact or vibration to the PC.
Operating Basics RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!. ■ You cannot use RecordNow!’s “Audio CD for Car or Home CD Player” function to record music to the DVD-R/-R DL/-RW or DVD+R/+R DL/ +RW disc. ■ Do not use the “Exact Copy” function of RecordNow! to copy DVDVideo and DVD-ROM with copyright protection.
Operating Basics When RecordNow! launched, it is possible that the disc tray of the DVD drive with the disc loaded is unable to be ejected even the "Eject" button is pressed. To solve this problem, please click on the "eject" button on the RecordNow! main screen, or right click on the icon of the DVD drive where the disc loaded, select "Eject" of the pop-up menu under "My Computer" or "Explore".
Operating Basics Video You can record video using WinDVD Creator 2 Platinum. When using WinDVD Creator 2 Platinum: You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator 2 Platinum. However, there is a case where its playback sound is choppy. 1. Click the Windows Start button and select the Control Panel option. 2. Click the Performance and Maintenance icon in the Control Panel. 3. Click the System icon in the Performance and Maintenance window. 4.
Operating Basics ■ Make sure that your computer is running on AC power when using WinDVD Creator. ■ Operate the computer at Full Power. Do not use power-saving features. ■ While you are editing DVD, you can display previews. However, if another application is running, the preview might not display properly. ■ WinDVD Creator cannot show video on the external monitor when in simultaneous mode. ■ WinDVD Creator cannot edit or play copy protected content.
Operating Basics ■ A maximum of about 2 hours of video data can be written in DVD Video format to DVD-R/+R/-RW/+RW disc. ■ WinDVD Creator cannot export to DVD-Audio, VideoCD, miniDVD format. ■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the disc may only play on your computer. ■ When writing to DVD disc, WinDVD Creator requires 2 GB or more over disk space every one hour of video. ■ When you make a fully recorded DVD, the chapter sequence may not play correctly. 3.
Operating Basics 6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not use benzine, thinner or similar cleaner. Diskettes 1. Store your diskettes in the container they came in to protect them and keep them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2.
Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Operating Basics Properties menu Click the icon with the secondary mouse button to display the following menu. The menu list (Windows XP) Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics Connecting To connect the internal modem cable, follow the steps below. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack. Modem Jack Telephone Jack Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.
Operating Basics Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 wireless LAN standard (Revision A, B or G) and Turbo Mode. Supported features. It supports the following features: ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s (Revision A and G, Revision A/B, B/G, A/B/G combo type).
Operating Basics Worldwide operation The Bluetooth radio transmitter and receiver operates in the 2.45 GHz band, which is license-free and compatible with radio systems in most countries in the world. Radio links You can easily establish links between two or more devices. The link is maintained even if the devices are not within line of sight.
Operating Basics LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) ,Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).(depend on model you purchased) This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off.
Operating Basics When the computer is exchanging data with the LAN, the LAN active indicator glows amber. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. Make sure the LAN active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2.
Operating Basics ■ ■ ■ ■ Close the display. Do not pick up the computer by its display panel. Close all port covers. Use the carrying case when transporting the computer. When carrying your computer, be sure to hold it securely so that it does not fall or hit anything. ■ Do not carry your computer by holding protruded portions. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor.
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard F1 ... F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off. Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad. Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key. Press Fn + Alt to simulate the enhanced keyboard’s right Alt key. Hotkeys Hotkeys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off.
The Keyboard Power save mode: Pressing Fn + F2 changes the power save mode. If you press Fn + F2, the Power Save Mode is displayed in a dialog box. Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the Plugged in or Running on batteries item of the Power Saver Properties window in Power Saver. Standby: When you press Fn + F3, the computer can enter Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification.
The Keyboard Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hotkeys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Screen brightness item of the Basic Setup window in Power Saver. Wireless setting: If your computer has both Bluetooth and wireless LAN functions, you can press Fn + F8 to select which type of wireless communication you want to use.
The Keyboard TOSHIBA Zooming Utility (reduce): To reduce the icon size on the desktop or the application window, press the 1 key while holding down the Fn key. TOSHIBA Zooming Utility (enlarge): To enlarge the icon size on the desktop or the application window, press the 2 key while holding down the Fn key. Fn Sticky key You can use the Toshiba Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key.
The Keyboard Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the center of the keyboard with white letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard in figure 5-1. Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control.
The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type uppercase characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Table Power conditions Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery flashes Amber DC IN off Battery charge is exhausted Computer goes into Hibernation or shuts down (depending on the Toshiba power Management Utility Setting) Power off (no operation) No battery installed • No operation • LED: Battery off DC IN off Power i
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Blue Indicates the AC adaptor is connected and supplying proper power to the computer. Amber Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, see your dealer. No light Under any other conditions, the indicator does not light. Power indicator Check the Power indicator to determine the power status.
Power and Power-Up Modes When the computer is powered off in Resume mode, and the AC adaptor is not connected, the battery pack supply power to maintain data and programs in memory. If the battery pack is completely discharged, Resume does not function and the computer loses all data in memory. The following message appears when you turn on the power: RESUME FAILURE. PRESS ANY KEY TO CONTINUE.
Power and Power-Up Modes Safety precautions Mishandling of batteries can cause death, serious injury or property damage. Carefully observe the following advisories: Danger: Indicates an imminently hazardous situation, Which could result in death or serious injury, if you do not follow instructions. Warning: Indicates a potentially hazardous situation, Which could result in death or serious injury, if you do not follow instructions.
Power and Power-Up Modes Warning 1. Never allow caustic electrolyte fluid leaked from a battery pack to contact your eyes, skin or clothing. If caustic electrolyte fluid should contact your eyes, immediately wash your eyes with large amounts of running water and seek medical attention, to help prevent eye damage. It electrolyte fluid should contact your skin immediately wash it under running water to prevent rash.
Power and Power-Up Modes Note 1. Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function. 2. To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures.
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type System on System off Battery pack (6 cell) 8 hours or more 4 hours Battery pack (9 cell) 8 hours or more 4 hours Battery pack (12 cell) 8 hours or more 5 hours RTC battery 24 hours Don’t charge The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored in TOSHIBA Power Saver. ■ Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (6 cell) about 2 days (Standby mode) about 20 days (Shutdown mode) Battery pack (9 cell) about 2 days (Standby mode) about 30 days (Shutdown mode) Battery pack (12 cell) about 4 days (Standby mode) about 40 days (Shutdown mode) RTC battery about 2 months Extending battery life To maximize the life of y
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator flashes amber shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install battery packs.
Power and Power-Up Modes 6. Slide the battery release latch to free the battery pack for removal, then lift up the battery pack. Battery Pack Lock Battery Release Latch Battery Pack Removing the battery pack 7. Pull the battery pack forward to remove it. For environmental reasons, do not throw away a spent battery pack. Please return spent battery pack to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
Power and Power-Up Modes Starting the computer by password To start up the computer with the user password, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message appears: Enter Password = At this point, the hotkeys Fn + F1 to F9 do not work. They will function after you enter the password. 2. Enter the password. 3. Press Enter. If you enter the password incorrectly three times in a row, the computer shuts off.
Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for display, boot priority, keyboard, USB, LAN, general and password. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
HW Setup and Passwords HW Setup window The HW Setup window contains the following tabs: Display, CPU, Boot Priority, Keyboard, USB, LAN, General, and Password. There are three buttons: OK, Cancel and Apply. OK Accepts your changes and closes the HW Setup window. Cancel Closes the window without accepting your changes. Apply Accepts all your changes without closing the HW Setup window. General This window displays the BIOS version and contains two buttons: Default and About.
HW Setup and Passwords If you click the OK button before entering the password, Not registered will appear on the display. 2. Click the OK button. The following message appears, allowing you to verify the password. Verify Password: 3. If character strings match, the password is registered click OK button. If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2.
HW Setup and Passwords Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you set the display to be used when the computer is booted. Auto-Selected Selects an external monitor if one is connected. Otherwise, it selects the internal LCD. (Default) LCD+AnalogRGB Selects both the internal LCD and external monitor for simultaneous display.
HW Setup and Passwords Boot Priority Boot Priority Options This option sets the priority for booting the computer. PC card HDD boot is not supported. To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. Use the up/down cursor keys to select boot device you want and press Enter. ■ IIf a supervisor password is set, the menu above does not appear when you use the user password to start the computer.
HW Setup and Passwords USB Legacy USB Support Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enabled Enables the USB KB/Mouse Legacy Emulation. (Default) Disabled Disables the USB KB/Mouse Legacy Emulation. LAN Wake-up on LAN This features lets the computer’s power be turned on when it receives a wake-up signal from the LAN.
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. In Windows® XP, open the Safely Remove Hardware icon on the system tray and disable the PC card. 2. Press the eject button of the PC card you want to remove to extend the button. 3. Press the extended eject button to pop the card out slightly. 4. Grasp the PC card and remove it.
Optional Devices 3. Check the configuration in the HW Setup window to make sure it is appropriate for your card. Express Card slot Inserting the Express Card Removing an Express Card To remove the Express Card, follow the steps below. 1. In Windows® XP, open the Safely Remove Hardware icon on the system tray and disable the Express Card. 2. Press the Express Card slightly to make it stretch out. 3. Grasp the Express Card and pull it out from the slot.
Optional Devices See below for the card capacities: Card Type Capacties SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, 1GB, 2GB MMC 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, 1GB MS 8MB, 16MB, 32MB, 64MB, 128MB, 256MB MS Pro 256MB, 512MB, 1GB, 2GB xD 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, 1GB Installing a SD/MS/MS Pro/MMC/xD card To install the memory card, follow the steps below. 1. Insert the memory card. 2. Press gently to ensure a firm connection.
Optional Devices Removing a SD/MS/MS Pro/MMC/xD card To remove the memory card, follow the steps below. 1. In Windows® XP, open the Safely Remove Hardware icon on the system tray and disable the inserted memory card. 2. Gently press the memory card inside the socket to eject it. 3. Grasp the card and remove it. SD/MS/MS Pro/MMC/xD card Removing the inserted memory card ■ Make sure the Multiple Digital Media Card Slot indicator is out before you remove the card or turn off the computer’s power.
Optional Devices Installing memory module To install a memory module, make sure the computer is in boot mode then: 1. Turn the computer off in boot mode. Refer to the Turning off the power section in Chapter 3. ■ If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. ■ Do not try to install a memory module with the computer turned on or turned off in Standby and Hibernation mode.
Optional Devices Inserting the memory module 8. Seat the cover and secure it with one screw. 9. When you turn the computer on, it should automatically recognize the total memory capacity. Use the HW Setup program to verify that the added memory is recognized. If it is not recognized, check the module’s connection. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer.
Optional Devices Removing the memory module 7. Seat the cover and secure it with one screw. Additional battery pack (6 Cell, 9 Cell and 12 Cell) You can increase the portability of the computer with one of the following additional battery packs: ■ 6 Cell: PA3399U-2BAS/PA3399U-2BRS ■ 9 Cell: PA3478U-1BAS/PA3478U-1BRS ■ 12 Cell: PA3400U-1BAS/PA3400U-1BRS If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes.
Optional Devices USB FDD Kit The 3 1/2" external FDD drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer, Port Replicator. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Connect the monitor to the external monitor port. 2.
Optional Devices 2. Use a video cable (not supplied) to connect the television to the video out port. VIDEO out port Connecting a television 3. Turn the television on. 4. Turn the computer on. i.LINK (IEEE1394) Some models are equipped with a i.LINK. i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as 1. Digital video cameras 2. Hard disk drives 3. MO drives 4. CD-RW drives i.LINK uses a four-pin connector, which does not carry electriccurrent.
Optional Devices 6. Make sure data transfer has ended or turn off the computer, before you: a. Connect/disconnect an i.LINK device to/from the computer. b. Connect/disconnect an i.LINK device to/from another i.LINK device that is connected to the computer. Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: a.
Optional Devices Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting ■ Make sure all options are set properly in the setup program. ■ Check all cables. Are they correctly and firmly attached? Loose cables can cause signal errors. ■ Inspect all connecting cables for loose wires and all connectors for loose pins. ■ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer.
Troubleshooting Software Hardware The problems may be caused by your software or diskette. If you cannot load a software package, the media (usually a diskette) may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the OS documentation.
Troubleshooting Self test When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow S TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the Hardware Setup, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow blue) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes. If the Battery indicator glows after 20 minutes, let the battery continue to charge at least another 20 minutes before turning on the computer. If the indicator still does not glow, the battery may be at the end of its operating life. Replace it. If you do not think the battery is at the end of its operating life, see your dealer.
Troubleshooting LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup and Passwords, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the LCD They might have come from contact with the keyboard, TouchPad or cPad. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner.
Troubleshooting DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting Problem Procedure Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning.
Troubleshooting Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. Some programs run correctly but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software needs. You cannot access the Try another diskette.
Troubleshooting Touch Pad/Dual Mode Pad Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to Pad shaped as an hourglass, waitfor it to resum its operation normal shape and try again to move it. User’s Manual Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. 3.
Troubleshooting USB mouse This section applies only with Windows® XP operating systems. Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to mouse shaped as an hourglass, wait for it to resume its normal shape and try again to move it. operation Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click sped setting in the mouse control utility. 1.
Troubleshooting SD/MS/MS Pro/MMC/xD card Refer also to Chapter 4, Operating Basics. Problem Procedure Memory card error occurs Reseat the memory card to make sure it is firmly connected. Check the card’s documentation. You cannot write to the Make sure the card is not write protected. memory card You cannot read a file Make sure the target file is on the memory card inserted in the slot. If problems persist, contact your dealer.
Troubleshooting Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer. If problems persist, contact your dealer.
Troubleshooting Problem Procedure If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard. If these devices do not work, make sure the USB KB/Mouse Legacy Emulation item in HW Setup is set to Enabled. If problems persist, contact your dealer. Modem Problem Procedure Communication software can’t initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Options in the Control Panel.
Troubleshooting Standby/Hibernation Problem Procedure The system will not enter Standby/ Hibernation Is Windows Media™ Player open? The system might not enter Standby/Hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Standby/ Hibernation. If problems persist, contact your dealer. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB.
Troubleshooting Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card is installed in the computer. The built-in Bluetooth function and an optional Bluetooth PC card cannot operate simultaneously.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 360 (w) × 267 (d) × 29.8 (front) / 36.8 (rear) millimeters Weight (typical*) < 3 kilograms, configured with: 15.4" panel, DVD Combo drive, 6-cell battery, and modem. * Weight will vary depending on whether or not and what kind of options are adopted.
Specifications Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications User’s Manual Communication System Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32/ V.32bis/V.34/V.90 Bell 103/212A Fax: ITU-T-Rec (Former CCITT) V.17/V.29/V.27ter /V.
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.
Display Controller and Modes Video Modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on, resolution, number of colors and refresh rates.
Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications User’s Manual From Factor ■ Mini PCI TypeIII Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio characteristics Radio characteristics of Wireless LAN cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4 GHz and 5 GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported frequency sub-bands Subject to the radio regulations that apply in your country/region, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region. Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 1 2 3 4 5 6 7 8 9 10 11 12 13 2400-2483.
Wireless LAN Wireless IEEE 802.
Wireless LAN Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 42 50 58 152 160 *1 *2 *3 *4 User’s Manual 5150-5850 MHz Note 5210*3 5250*3 5290*3 5760*3 5800*3 US only*4 US only*4 US only*4 US only*4 US only*4 Factory-set default channels Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used. These channels are available to A/B/G combo type only. Available Area: US (USA, CANADA) only.
Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe and China. .
Appendix E If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office. Make a note of your computer’s machine type, model number, and serial number, and put it in a safe place.
If your computer is stolen To register the theft online, please follow these procedures: ■ Visit www.toshiba-europe.com on the Internet. In the product area, choose Computer Systems. ■ In the Computer Systems page, open the Support & Downloads menu and choose the Stolen Units Database option. Your entries are used to track your computer at our service points. TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr.
Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
Glossary IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MDA: monochrome display adapter MPEG: moving picture coding experts group MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect PCMCIA: Personal Computer Memory Card International Association RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock.
Glossary A adapter: A device that provides an interface between two dissimilar electronic devices. For example, the AC adapter modifies the power from a wall outlet for use by the computer. This term also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices. allocate: To assign a space or function for a specific task.
Glossary BIOS: Basic Input Output System. The firmware that controls data flow within the computer. See also firmware. bit: Derived from ìbinary digit,î the basic unit of information used by the computer. It is either zero or one. Eight bits is one byte. See also byte. Bluetooth: A short-range radio technology designed to simplify wireless communication among computers, communication devices and the Internet. board: A circuit board.
Glossary CGA: Color/graphics adapter. A video display protocol defined by the IBM Color/Graphics Monitor Adapter and its associated circuitry. This protocol supports two-color 640 × 200 and four-color 320 × 200 graphics, and 16-color 640 × 200 and 320 × 200 text modes. character: Any letter, number, punctuation mark, or symbol used by the computer. Also synonymous with byte. chassis: The frame containing the computer.
Glossary CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a fluorescent screen-producing luminous spots. An example is the television set. cursor: A small, blinking rectangle or line that indicates the current position on the display screen. D data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters.
Glossary E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to the printer, the printer is said to echo the CRT. EGA: Enhanced Graphics Adapter.
Glossary G gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. GND: Ground. An RS-232C signal used in the exchange of data between a computer and serial device. graphics: The use of drawings, pictures, or other images, such as charts or graphs, to present information. H hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hard disk: A non-removable disk usually referred to as drive C. Also called fixed disk.
Glossary input: The data or instructions you provide to a computer, communication device or other peripheral device from the keyboard or external or internal storage devices. The data sent (or output) by the sending computer is input for the receiving computer. instruction: Statements or commands that specify how to perform a particular task. interface: 1) Hardware and/or software components of a system used specifically to connect one system or device to another.
Glossary M main board: See motherboard. MDA: Monochrome Display Adapter. A video display protocol defined by the IBM Monochrome Display Adapter and its associated circuitry for direct drive TTL displays that supports a monochrome 720 × 350 text mode. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen.
Glossary O OCR wand: A device that reads, using an optical device, hand written or machine printed symbols into a computer. See also OCR. OCR: Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device. on-line state: A functional state of a peripheral device when it is ready to receive or transmit data. operating system: A group of programs that controls the basic operation of a computer.
Glossary port: The electrical connection through which the computer sends and receives data to and from devices or other computers. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached. The board itself is typically flat and rectangular, and constructed of fiberglass, to form the attachment surface. program: A set of instructions a computer can execute that enables it to achieve a desired result. See also application.
Glossary serial interface: Refers to a type of information exchange that transmits information sequentially, one bit at a time. Contrast: Parallel interface. serial port: A communications port to which you can connect devices, such as a modem, mouse, or serial printer. serial: The handling of data bits one after the other. SIO: Serial Input/Output. The electronic methodology used in serial data transmission.
Glossary V VGA: Video graphics array is an industry standard video adapter that lets you run any popular software. volatile memory: Random access memory (RAM) that stores information as long as the computer is connected to a power source. W Warm dock/undock: Connecting or disconnecting a device to or from the computer while the computer is suspended. warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application or document.
Index A AC adaptor, 1-7, 2-5 DC IN 15V port, 2-5 additional, 1-14, 8-9 connecting, 3-5 Accessing, 7-1 Analyzing the problem, 9-2 Arrow mode, 5-7 ASCII characters, 5-8 Auto power on, See Power B Battery charger, 8-9 battery life, 6-10 Battery pack additional, 8-9 location, 2-6 battery pack, 6-4 Battery, See also Battery pack indicator, 2-9 C Cache memory CPU cache, 1-3 Level 2 cache, 1-3 CD-RW/DVD drive, 1-5, 4-17 Charging, 6-7 Cleaning the computer, 4-35 COM level, see Ports, serial cursor, 5-3 D Disk i
Index Fingerprint sensor location, 4-2 using, 4-3 Fn + Alt, 5-3 Fn + Ctrl, 5-3 Fn + Enter, 5-3 Fn + Esc, 5-3 Fn + F1, 5-3 Fn + F10, 5-2 Fn + F11, 5-2 Fn + F12 (ScrLock), 5-3 Fn + F2, 5-4 Fn + F3, 5-4 Fn + F4, 5-4 Fn + F5, 5-4 Fn + F6, 5-4 Fn + F7, 5-5 Fn + F8, 5-5 Fn + F9, 5-5 Fn key, 5-2 Fn Sticky key, 5-6 function keys, 5-2 G General, 7-2 H Hard disk drive, 1-4, 9-7 automatic power off, 1-10 Hardware and system checklist, 9-3 Hibernation, 1-11, 5-4 Hot keys, 1-10 Hotkeys, 5-3 HW Setup, 1-12 Boot Priori
Index Numeric mode, 5-7 O Operating System, 1-10 P Panel power on/off, See Power Parallel, 1-7 Password, 7-2, 9-6 power on, 1-10 PC card, 1-8, 9-13 installing, 8-2 location of slots, 2-2 removing, 8-3 Ports DC IN 15V, 2-5 external monitor, 1-7, 2-2 headphone, See Sound system infrared, 1-7, 2-2 LAN, 2-5 microphone, See Sound system modem, 2-4 USB, 1-7, 2-4, 2-5 Power, 9-4 button location, 2-7 indicator, 2-9 panel power on/off, 1-11 restarting, 3-10 turning off, 3-7 turning on, 3-6 Power save mode, 5-4 Pr
Index TV output signal, 9-15 types, 6-3 Typewriter keys, 5-1 U Utilities list, 1-12 USB, 1-7, 7-6, 9-15 location, 2-4, 2-5 user, 7-2 using, 4-32 V Video modes, Appendix B Video RAM, 1-3 Video-out jack, 1-7, 2-3 Volume control, See Sound system W Windows special keys, 5-6 Wireless LAN, 1-9, 9-17 using, 4-32 User’s Manual Index-4
