Satellite®/Satellite Pro® L40/ L50/L70/S50-C Series User’s Guide If you need assistance: Technical support is available online at Toshiba’s Web site at support.toshiba.com. At this Web site, you will find answers for many commonly asked technical questions plus many downloadable software drivers, BIOS updates, and other downloads. For more information, see “If Something Goes Wrong” on page 123 in this guide.
California Prop 65 Warning This product contains chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. For the state of California only.
Protection of Stored Data For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM.
FCC Notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Bluetooth® Wireless Technology Interoperability NOTE This section is only applicable if your system has a Bluetooth® module. Bluetooth® modules are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖ ❖ Bluetooth Specification as defined and approved by The Bluetooth Special Interest Group.
Bluetooth® Wireless Technology and Your Health The products with Bluetooth® wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is much less than the electromagnetic energy emitted by wireless devices such as mobile phones.
Wireless Interoperability Wireless LAN products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs (Revision a/b/g/n/ ac), as defined and approved by the Institute of Electrical and Electronics Engineers. ❖ The Wireless Fidelity (Wi-Fi®) certification as defined by the Wi-Fi Alliance.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment. Exposure to Radio Frequency Radiation The radiated output power of the Wireless LAN is far below the FCC radio frequency exposure limits.
Canada – Industry Canada (IC) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. Industry Canada requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High-power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: Supplementary *The product complies with the Information: requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/5/EC, compatible with the RoHS Directive 2011/65/EU and the Eco Design Directive 2009/125/EC (ErP) and the related implementing measures. This product is carrying the CE-Mark in accordance with the related European Directives.
In the European Union, these symbols indicate that when the last end user wishes to discard this product, it must be sent to appropriate facilities for recovery and recycling. This Directive applies to EU member countries only and does not apply to end users in other countries such as the United States.
Bande de fréquence restreinte: seuls les canaux 1- 7 (2400 et 2454 MHz respectivement) doivent être utilisés endroits extérieur en France. Vous pouvez contacter l’Autorité de Régulation des Télécommunications (http://www.arttelecom.fr) pour la procédure à suivre. License required for indoor use. Use with outdoor installations not allowed. È necessaria la concessione ministeriale anche per l’uso interno. Italia: Nederland: Verificare con i rivenditori la procedura da seguire.
❖ To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply. The user should use the wireless LAN utility to check the current channel of operation. If operation is occurring outside of the allowable frequencies as listed above, the user must cease operating the Wireless LAN at that location and consult the local technical support staff responsible for the wireless network.
The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations. Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery. Using this Equipment in Japan In Japan, the frequency bandwidth of 2,400 MHz to 2,483.
The indication shown below appears on this equipment. (1) (2) (3) 2.4FH1 (4) 1 2 3 4 2.4: This equipment uses a frequency of 2.4 GHz. FH: This equipment uses FH-SS modulation. The interference range of this equipment is less than 10m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. 3.
Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. © 2015 by Toshiba America Information Systems, Inc. All rights reserved. Export Administration Regulation This document contains technical data that may be controlled under the U.
Trademarks Satellite, Satellite Pro, and eco Utility are either registered trademarks or trademarks of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Adobe and Photoshop are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
Computer Recycling Information As part of a commitment to people and the future, Toshiba promotes the efficient use of resources by working to achieve our zero-wasteto-landfill goal at all our production sites. In addition to our existing waste reduction and recycling policies, Toshiba is strongly committed to reducing electronic waste.
Contents Introduction.......................................................26 This guide ............................................................ 28 Safety icons ......................................................... 29 Other icons used............................................ 29 Your computer’s features and specifications ........................................... 30 Documentation .................................................... 30 Service options ...........................................
Contents 21 Check list ....................................................... 36 Precautions .................................................... 37 Important information on your computer’s cooling fan................................................ 39 Setting up your computer .................................... 39 Connecting to a power source ............................ 40 Charging the main battery ................................... 42 Using the computer for the first time ...................
Contents Using a computer lock................................... 64 Chapter 2: Learning the Basics.............................. 66 Computing tips .................................................... 66 Using the keyboard.............................................. 67 Function keys................................................. 68 Special Windows® keys ................................ 69 Backlit keyboard .................................................. 69 Touch screen ..........................
Contents 23 Using the eco power plan .................................... 88 Changing the main battery................................... 89 Removing the battery from the computer...... 90 Inserting a charged battery ............................ 91 Taking care of your battery .................................. 92 Safety precautions ......................................... 92 Maintaining your battery ................................ 93 Disposing of used batteries .................................
Contents Function Key ...................................................... 120 Recovery Media Creator .................................... 121 Service Station................................................... 121 TOSHIBA Application Installer ........................... 122 Chapter 6: If Something Goes Wrong .................. 123 Problems that are easy to fix ............................. 123 Problems when you turn on the computer ........ 124 The Windows® operating system is not working .........
Contents 25 Disabling or enabling the touch pad ............ 154 Media buttons .............................................. 154 Volume Mute ................................................ 154 Disabling or enabling wireless devices ........ 155 Zoom In/Out................................................. 155 Keyboard Backlight...................................... 155 Zoom (Display resolution) ............................ 155 Appendix B: Power Cord/Cable Connectors........156 Glossary.................
Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba computer, your work and entertainment can accompany you wherever you go. Your computer is ENERGY STAR® qualified. Toshiba is a partner in the Environmental Protection Agency’s (EPA) ENERGY STAR® Program and has designed this computer to meet the latest ENERGY STAR® guidelines for energy efficiency.
Introduction 27 When considering additions to your home office, purchase products that have earned the ENERGY STAR® for all your equipment needs, which can save you money, save energy, and help protect the climate. Visit http://www.energystar.gov or http://www.energystar.gov/powermanagement for more information regarding the ENERGY STAR® Program.
Introduction This guide NOTE The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba’s Web site at support.toshiba.com.
Introduction Safety icons 29 Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Introduction Documentation Your computer’s features and specifications Certain computer chassis are designed to accommodate all possible configurations for an entire product Series. Your select model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis, unless you have selected all those features. This information applies to all the features and icons described in this guide.
Chapter 1 Getting Started This chapter provides tips for using your computer effectively, summarizes how to connect components, and explains what to do the first time you use your computer. Please read the safety instruction information on the Quick Start document (that shipped with your computer) carefully and make sure you fully understand the instructions before you attempt to use your computer in order to avoid potential hazards that could cause bodily injury, property damage, or damage the computer.
Getting Started Selecting a place to work ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ❖ Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals.
Getting Started Selecting a place to work 33 ❖ When typing, keep your wrists straight and try not to rest your wrists on the notebook. Support your arms on your forearm area. The forearms can be supported by the chair arm supports or the desk surface. ❖ The notebook display should be tilted so that the image on the screen is clear. ❖ Avoid glare: position the notebook so that light sources (lamps or windows) do not shine or reflect directly into your eyes.
Getting Started Selecting a place to work ❖ When using a notebook for long hours, it may be more comfortable to dock the notebook and use an external keyboard, mouse and monitor. ❖ The keyboard and mouse (or trackball) should be close to your elbow level. ❖ The mouse should be next to the keyboard to avoid a reach. If you have to reach, the arm should be supported in the forearm area by the desk surface or the chair arm supports.
Getting Started Selecting a place to work 35 Taking breaks and varying tasks ❖ Change the way you work so that you are not stuck in the same posture for long periods of time. Some people find it comfortable to occasionally stand while using the notebook. To do this properly, the notebook needs to be on an elevated surface. Make sure you follow the Good Working Posture points mentioned above while working. ❖ Take short, strategically spaced rest breaks to avoid eye strain and body fatigue.
Getting Started Selecting a place to work Seeking additional help Follow the advice from your employer’s company health and safety staff. Contact them if you need assistance making adjustment to your workstation or adjusting the lighting. Again, if you experience persistent or recurrent pain, ache, numbness, burning, or stiffness you should promptly see a qualified health care provider. These sensations may be caused by serious medical conditions that can be treated.
Getting Started Selecting a place to work 37 Precautions Your computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer. ❖ Avoid prolonged physical contact with the underside or surface of the computer. Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture.
Getting Started Selecting a place to work Consider using a hard computer insulating pad or similarly suitable hard insulating material when using a computer on your lap. Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer. It could damage the computer or cause system failure. ❖ Never turn off the computer if a drive light indicates a drive is active.
Getting Started Setting up your computer 39 Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep mode).
Getting Started Connecting to a power source NOTE Please handle your computer carefully to avoid scratching or damaging the surface. Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery. Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly.
Getting Started Connecting to a power source 41 California Prop 65 Warning This product contains chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. _ + 2 NOTE 3 Plug the AC adaptor cord into the DC-IN on the side of the computer. To locate your DC-IN port, please refer to your Quick Start document. Connect the power cord/cable to a live electrical outlet.
Getting Started Charging the main battery Charging the main battery Before using the battery to power the computer, you must charge the battery. To charge the battery, leave the computer plugged into an AC power source with the computer turned off until the battery light glows white. After that, the battery will be completely charged and ready to power the computer. NOTE Battery life and charge time may vary depending on the applications power management settings, and features used.
Getting Started Registering your computer with Toshiba 43 Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. NOTE The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices. The first time you turn on your computer, the setup guides you through steps to set up your software. Follow the onscreen instructions.
Getting Started To Shut down your computer To Shut down your computer 1 Press the Windows® ( screen. ) key to display the Start Pressing the power button before shutting down the Windows® operating system could cause you to lose your work. Make sure the system indicator panel’s storage drive light and the drive in-use light are off. If you turn off the power while a disk/disc is being accessed, you may lose data or damage the disk/disc and/or drive.
Getting Started To Restart your computer 45 To Restart your computer 1 Press the Windows® ( screen. 2 Click or touch the Power ( corner of the screen. ) key to display the Start ) icon at the upper-right Restart option (Sample Image) Restart 3 Highlight Restart, and then click or touch the Restart option. The computer closes all open applications, and restarts the operating system. To place your computer in Sleep mode 1 Press the Windows® ( screen.
Getting Started Adding optional external devices Adding optional external devices NOTE Before adding external devices, Toshiba recommends setting up your software. See “Setting up your software” on page 43.
Getting Started Recovering the Internal Storage Drive 47 A recovery image of your computer is stored on the internal storage drive, and the image can be restored by running the recovery utilities directly from your internal storage drive as described in the sections below. However, it is strongly recommended that you create recovery media. If the recovery files on your internal storage drive become corrupted or are deleted, you can restore your system from your recovery media.
Getting Started Recovering the Internal Storage Drive NOTE When you create recovery media, only the operating system files and drivers originally shipped with the computer are backed up to the external media and can be restored from this media. Any files that you created are not backed up on the recovery media. You will need to separately back up the files you created; for more information, see “Backing up your work” on page 73.
Getting Started Recovering the Internal Storage Drive 49 2 Select DVD or USB Flash from the drop-down list, depending on the type of external media you want to use. 3 Check the “Information” area of the dialog box to determine the number of DVDs you will need and/or the minimum amount of storage space required for copying your system’s recovery files to USB flash drive(s). 4 Do one of the following: ❖ If you are copying files to DVD, insert a blank DVD into the optical disc drive.
Getting Started Recovering the Internal Storage Drive Restoring from recovery media The recovery process deletes information stored on the internal storage drive. Be sure to save your work to external media before executing the recovery (see “Backing up your work” on page 73). NOTE During the recovery process your computer must be connected to an external power source via the AC adaptor. If you have created recovery media for your system, you can restore your system from such media, if necessary.
Getting Started Recovering the Internal Storage Drive 51 5 A warning screen appears, stating that when the recovery is executed all data on your internal storage drive will be deleted and rewritten. Click or touch Yes to continue. 6 Follow the on-screen instructions to complete the recovery process. When the process is complete, a message displays indicating that the drive has been recovered. 7 Click or touch Finish to restart the computer.
Getting Started Recovering the Internal Storage Drive 3 Click or touch Change PC Settings. The PC settings window appears. (Sample Image) PC settings screen 4 Click or touch Update and recovery. 5 Click or touch Recovery. 6 Under Refresh your PC without affecting your files, click or touch Get Started. The “Refresh your PC” screen appears. (Sample Image) Refresh your PC screen Toshiba does not guarantee successful data back up.
Getting Started Recovering the Internal Storage Drive 7 53 Click or touch the Next button to begin. The “Ready to refresh your PC” screen appears. (Sample Image) Ready to refresh your PC screen You will be prompted to refresh your system. 8 Click or touch the Refresh button. 9 Your system will restart. The “Refreshing your PC” window appears. When the process is complete your system will reboot your Windows® operating system.
Getting Started Recovering the Internal Storage Drive 3 Click or touch Change PC Settings. The PC settings window appears. (Sample Image) PC settings screen 4 Click or touch Update and recovery. 5 Click or touch Recovery. 6 Under Remove everything and reinstall Windows, click or touch Get Started. The “Reset your PC” screen appears.
Getting Started Recovering the Internal Storage Drive 7 55 Click or touch the Next button. The “Do you want to fully clean your drive?” screen appears. (Sample Image) Do you want to fully clean your drive screen 8 Select one of the following options: ❖ Just remove my files ❖ Fully clean the drive The “Ready to reset your PC” screen appears. (Sample Image) Ready to reset your PC screen 9 Click or touch the Reset button. The “Resetting your PC” window appears.
Getting Started Recovering the Internal Storage Drive NOTE Selecting the “Fully clean the drive” option may take several hours. Installing drivers and applications The TOSHIBA Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. NOTE You must have an Internet connection to reinstall applications.
Getting Started Using the touch pad 57 Using the touch pad NOTE Some of the touch pad operations described in this section are only supported in certain applications, and only on certain models.
Getting Started Using the touch pad To: Do the following: Move the onscreen pointer Slide your finger across the touch pad in the direction you want to move the pointer. To move the pointer a longer distance, slide your finger several times across the touch pad in the preferred direction. Select an item Example: (Sample Illustration) Pointer moves to the right 1 Move the pointer to the item you want to select.
Getting Started Using the touch pad To: Do the following: Scroll horizontally Slide your finger along the bottom edge of the touch pad in the direction you want to scroll. Repeat to scroll a longer distance. 59 Example: (Sample Illustration) Horizontal scrolling active area Zoom in/out To zoom in: ❖ Place two fingers close together on the touch pad and then slide them apart.
Getting Started Using the touch pad ❖ Temporarily disable the touch pad, so that it does not respond to touch or button presses while you type. See “Disabling or enabling the touch pad” on page 60. ❖ Adjust the sensitivity of the touch pad, so that it is less responsive to accidental light taps and lighter finger pressure. NOTE Touch pad setting options vary by computer model. The touch pad settings are accessible through the Mouse Properties option of the Windows Control Panel.
Getting Started Using external display devices 61 Using external display devices Your computer comes with a built-in display, but you can also connect an HDMI™-compatible television or external display device via the HDMI™ Out port*. NOTE To locate your HDMI™ Out port, please refer to your Quick Start document.
Getting Started Using external display devices Directing the display output when you turn on the computer Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. NOTE Some modes are only available with the appropriate device attached and turned on.
Getting Started Customizing your computer’s settings 63 NOTE The Windows® ( ) + P keys to navigate through the options without activating a selection. Press ENTER to activate a selection. NOTE You may also use the F4 key, and then press ENTER to activate a selection. Adjusting the quality of the external display To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings.
Getting Started Caring for your computer Cleaning the computer Keep liquids, including cleaning fluid, out of the computer’s keyboard, speaker, and other openings. Never spray cleaner directly onto the computer and/or display. Never use harsh or caustic chemical products to clean the computer. To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth.
Getting Started Caring for your computer 3 65 Insert the cable’s locking end into the security lock slot on your computer, then engage the locking device. The computer is now securely locked.
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the internal storage drive. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Learning the Basics Using the keyboard ❖ 67 Back up your files to external media on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your internal storage drive suddenly fails, you will lose all the data on it unless you have a separate backup copy. For more information, see “Data and system configuration backup in the Windows® operating system” on page 143.
Learning the Basics Using the keyboard (Sample Illustration) Keyboard (Sample Illustration) 10-key keyboard (Available on certain models) NOTE To capture a print screen of the entire screen, press the FN + PRTSC key. (This only applies to models with a 10-key keypad.) To capture only the active window displayed, press FN + ALT while simultaneously pressing the PRTSC key.
Learning the Basics Backlit keyboard 69 F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the FN key, function keys marked with icons execute specific functions on the computer. For example, F5 turns the touch pad ON/OFF. For more information, see “TOSHIBA Function Keys” on page 151.
Learning the Basics Touch screen Touch screen navigation Use your finger to manipulate the on-screen icons, buttons, menu items, and other items on the touch screen. You can also change the screen’s orientation. The screen is made of glass so avoid contact with sharp, rough, or abrasive objects or substances as screen may break or scratch if not handled properly. If you see a crack in the glass, discontinue use of the device to avoid injury.
Learning the Basics Mouse properties 71 Swipe from left edge—Swipe in from the left edge to display an open app. Snaps open apps (swipe in from the left edge and slide the divider to adjust the app size). Displays recently opened apps (swipe in from left edge, holding your finger down, and then push the app back toward the left edge). Swipe from top or bottom edge—Swipe in from the top or bottom edge to display commands. You can also close an app by dragging it to the bottom of the screen.
Learning the Basics Saving your work Starting an app from the Start screen To start an app on the Start screen, move your pointer over the appropriate tile and click or touch to open. Swipe your finger to the left or right to reveal more available tiles. To search for an app using the Apps page, click or touch the Down arrow ( ) icon in the lower-left corner of the Start screen. The Apps screen appears with the available system apps to choose from, or you can enter your search in the search field.
Learning the Basics Backing up your work 73 Backing up your work Back up all the files you create in case something happens to your computer. You can back up your files to different types of media such as USB Flash, CDs, DVDs, external storage media, or to a network, if available. To back up several files at one time, use the Microsoft® Windows® file recovery program preinstalled on the computer’s internal storage drive.
Learning the Basics Using the optical disc drive NOTE When viewing DVD movies use the DVD Player software that came with your computer. Optical disc drive components The optical disc drive is located on the side of the computer. Your optical disc drive may look like this: Drive in-use indicator light Eject button Manual eject hole (Sample Illustration) Optical disc drive Drive in-use indicator light—Indicates when the drive is in use. Eject button—Press to release the disc tray.
Learning the Basics Using the optical disc drive 75 Media control buttons The media control buttons located above the keyboard allow you mute the sound and play audio CDs or DVD movies when the computer is on. Volume decrease button Play/pause button Previous track button Next track button Volume increase button Mute button (Sample Illustration) Media control buttons The Previous track button allows you to restart playing the current track or go to the previous track.
Learning the Basics Using the optical disc drive Handle DVDs and CDs carefully, making contact only with the center hole and edge. Do not touch the surface of the disc. Do not stack discs. If you incorrectly handle the discs, you could lose data. 6 Push the disc tray in by pressing gently on the center of the tray until it clicks into place. If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance.
Learning the Basics Using the optical disc drive NOTE 77 Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your Toshiba optical disc drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or optical media recorders.
Learning the Basics Toshiba’s online resources Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Pull the tray out until it is fully open, remove the disc, and place it in its protective cover. 3 Gently press the tray in to close it. Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been preset by Toshiba.
Mobile Computing Running the computer on battery power Battery Notice Battery life rating is for comparison purposes only, and does not indicate the battery life that will be obtained by any individual user. Actual battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components.
Mobile Computing Charging batteries 81 The RTC battery powers the RTC memory that stores your system configuration settings and the current time and date information. It maintains this information for up to a month while the computer is turned off. TECHNICAL NOTE: Depending on your system, the RTC battery may only charge while the computer is turned on.
Mobile Computing Charging batteries TECHNICAL NOTE: The recharging of the battery may not occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices. Your computer's Power Options utility can be used to select a power level setting that reduces the power required for system operation and will allow the battery to recharge. The battery may not start charging immediately under the following conditions: ❖ The battery is extremely hot or cold.
Mobile Computing Monitoring battery power NOTE 83 Depending on your system, the RTC battery may only charge while the computer is turned on. To recharge the RTC battery, plug the computer into a live electrical outlet and leave the computer powered on for 24 hours. NOTE It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working.
Mobile Computing Monitoring battery power NOTE If the AC power light flashes amber during charging, either a battery pack is malfunctioning, or it is not receiving correct input from the AC power supply. HINT: Be careful not to confuse the AC power light/ Battery light ( ) and the power button ( ) light. When the AC power light/Battery light or power button light flashes amber, it indicates that the system is suspended (using the Windows® operating system Sleep command).
Mobile Computing Monitoring battery power 85 TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 50 degrees Fahrenheit. The computer calculates the remaining battery charge based on your current rate of power use and other factors such as the age of the battery.
Mobile Computing Monitoring battery power 4 Click or touch Change advanced power settings. The Advanced settings tab of the Power Options window appears. 5 Double-click or touch Battery to display the battery options. (Sample Image) Advanced settings tab of Power Options screen 6 Configure the alarm settings to suit your needs.
Mobile Computing Monitoring battery power 87 These power-saving options control the way in which the computer is configured. By using them, you can increase the length of time you can use the computer before you need to recharge the battery. Microsoft® has combined these options into preset Power Plans. Using one of these power plans lets you choose between maximum power savings and peak system performance. You may also set individual power-saving options to suit your own needs.
Mobile Computing Using the eco power plan NOTE 5 To edit a plan or to edit advanced settings, continue to the following steps. Click or touch Change plan settings to choose the plan you want to edit. This screen allows you to change basic settings. 6 Click or touch Change advanced power settings to access settings for battery notification levels, internal storage drive power save time, etc.
Mobile Computing Changing the main battery 89 Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged battery. If you find that a new battery is needed, contact the location where you purchased the computer for more information on replacing the battery. Toshiba will not be responsible for any product damage, data loss, service, or part replacement made necessary by improper installation of a new battery.
Mobile Computing Changing the main battery Removing the battery from the computer To remove the battery: 1 Save your work. 2 Turn off the computer, see “To Shut down your computer” on page 44. 3 Unplug and remove any cables connected to the computer, including the AC adaptor. 4 Close the display panel and turn the computer upside down. NOTE 5 Depending on your model, the battery will either have latches or screws, allowing for the removal of the battery.
Mobile Computing Changing the main battery 91 If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately. Always dispose of used battery packs in compliance with all applicable laws and regulations. Put insulating tape, such as cellophane tape, on the electrode during transportation to avoid a possible short circuit, fire or electric shock. Failure to do so could possibly result in serious injury.
Mobile Computing Taking care of your battery Battery screws (Sample Illustration) Locking the battery 4 Turn the computer right side up. 5 Reconnect any cables that were removed in step 3 of “Removing the battery from the computer” on page 90. 6 Restart the computer. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life.
Mobile Computing Disposing of used batteries 93 Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. ❖ If you have extra battery packs, rotate their use (for models with an accessible battery only).
Mobile Computing Traveling tips Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User's Manual. Other battery packs have different voltage and terminal polarities. Use of non-conforming battery packs could generate smoke or cause fire or rupture, possibly resulting in serious injury. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them.
Mobile Computing Traveling tips 95 TECHNICAL NOTE: When traveling by air, you may be required to pass your computer through airport security equipment. The X-ray equipment will not harm your computer. NOTE Before using your computer aboard an aircraft, make sure the Wireless antenna is OFF (Airplane mode is ON) if your computer has wireless LAN capability. NOTE To enable or disable wireless communication, use the F12 key. For more information see “TOSHIBA Function Keys” on page 151.
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your computer. Exploring the Start screen The Start screen is the launching pad for everything you can do in the Windows® operating system, providing new and easy ways to access everything from your favorite apps and Web sites to your contacts and other important information.
Exploring Your Computer’s Features Exploring the Start screen 97 For detailed information on the new functionality, refer to the Windows® Help and Support. Search icon Power icon Apps page icon App tiles (Sample Image) Windows® Start screen Charms Use the Windows® charms to start apps, find documents, set up system components, and perform most other computing tasks.
Exploring Your Computer’s Features Exploring the desktop Tiles Tiles can be accessed and launched from the Start screen. Typical Start screen tiles are the Desktop tile and Mail tile, as well as tiles representing all other applications downloaded to your system. Exploring the desktop You can use its features to start applications, find documents, set up system components, and perform most other computing tasks.
Exploring Your Computer’s Features Exploring the desktop 99 Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking or touching the icon. You can create a new desktop icon for any folder, file, or program by dragging the element’s icon from its location in a window to the desktop area. You may see various icons displayed on your system desktop, for example: Recycle Bin—Holds files you have deleted.
Exploring Your Computer’s Features Windows® Store Notification area The notification area displays icons of tasks or programs that run continuously in the background and displays notifications. To learn more about each task, position the pointer over the icon for a few moments and a short description of the task appears. Typical tasks in the notification area are Current time, Power usage mode, network connectivity status, and speaker volume.
Exploring Your Computer’s Features Setting up for communications 101 In the Windows® Store you can search for and browse thousands of apps, all grouped into easy to find categories. Setting up for communications To connect to the Internet you need: ❖ A browser or communications program ❖ An Internet Service Provider (ISP) or online service if you plan to use the Internet ❖ A way to connect to the ISP (for example Wi-Fi®/broadband connection, etc.
Exploring Your Computer’s Features Exploring audio features For help with common Wi-Fi® networking problems, see “Wireless networking problems” on page 139. Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality. Accessing a network For specific information about connecting to the network, consult your network administrator. Many hotels, airports, and offices offer Wi-Fi® access.
Exploring Your Computer’s Features Exploring audio features 5 103 When you have finished recording, click or touch the Stop Recording button. The Save As dialog box appears. 6 To save the file, type a file name, and then click or touch Save. Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers.
Exploring Your Computer’s Features Using the Web Camera Using the Web Camera Your computer may come with a built-in Web Camera. With this Web Camera you can do the following: ❖ Take pictures and record videos with your computer ❖ Chat with others and have them see you while using instant messaging (IM) programs ❖ Have video conference calls NOTE To email, instant message or video conference, you must be connected to the Internet.
Exploring Your Computer’s Features Using the Memory card reader 105 Inserting memory media NOTE To locate your Memory card reader, please refer to your Quick Start document. The following instructions apply to all types of supported media devices. 1 Turn the media so that the contacts (metal areas) are face down. 2 Push the media into the adapter until it stops. (Sample Illustration) Inserting memory media When inserting memory media, do not touch the metal contacts.
Exploring Your Computer’s Features Using the Memory card reader 3 Highlight, and then click or touch the item you would like to eject. If the system is unable to prepare the media for safe removal, a message will tell you to try again later. If the media can be removed now, the system displays Safe to Remove Hardware. If the computer has a spring-loaded adapter slot, see step 4; otherwise, skip to step 5. 4 Gently press the card inward to release it. The card pops out slightly.
Chapter 5 Utilities Your computer includes several utilities designed to help you to reconfigure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter. NOTE The utilities described in this chapter, and the icons shown in the sample images are applicable only if the related utility is available on your system.
Utilities eco Utility® eco Utility® The eco Utility® monitors your power savings from using the eco power plan by tracking real-time power consumption and accumulated savings over time. To access the eco Utility®: 1 From the Start screen begin typing eco Utility. 2 Click or touch eco Utility. The eco Utility® window appears. (Sample Image) eco Utility® window 3 To activate the eco power plan, select eco Mode on the left side. 4 Click or touch the eco Mode button. 5 Click or touch Close.
Utilities Password Utility 109 Password Utility Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can work on your computer again. TOSHIBA supports different types of passwords on your computer: ❖ A supervisor password—Prohibits unauthorized users from accessing certain functions such as System Settings. This is useful if more than one person uses the computer.
Utilities Password Utility To set a supervisor password: 1 To access Supervisor Password from the Start screen begin typing Password Utility. 2 Click or touch Password Utility. (Sample Image) Supervisor Password tab 3 Click or touch Supervisor Password. 4 Click or touch Set. 5 Enter your password, and then enter it again to verify. 6 Click or touch Set. NOTE 7 NOTE Under User Policy, this option may or may not ask for password verification.
Utilities Password Utility 111 Deleting a supervisor password To delete a supervisor password: 1 To access Supervisor Password from the Start screen begin typing Password Utility. 2 Click or touch Password Utility. A pop-up screen appears asking for a password. 3 Enter your password, and then click or touch Verify. 4 Click or touch Supervisor Password. 5 Click or touch Delete. An authority verification pop-up screen appears. 6 Click or touch Delete.
Utilities Password Utility To register a password for the power-on password functions: 1 To access User Password from the Start screen begin typing Password Utility. 2 Click or touch Password Utility. 3 Click or touch User Password. (Sample Image) User Password tab 4 Click or touch Set. 5 Enter your password, and then enter it again to verify. 6 Click or touch Set. 7 Click or touch OK to save your password as a text file. NOTE Password Utility will suggest “memo.
Utilities Password Utility 113 Deleting a user password To cancel the power-on password function: 1 To access User Password from the Start screen begin typing Password Utility. 2 Click or touch Password Utility. A pop-up screen appears asking for a password. 3 Enter your password, and then click or touch Verify. 4 Click or touch Delete. An authority verification pop-up screen appears. 5 Click or touch Delete. 6 Enter the password, and then click or touch Verify. 7 Click or touch OK to exit.
Utilities System Settings System Settings System Settings is the TOSHIBA configuration management tool available through the Windows® operating system. To access it: 1 To access System Settings from the Start screen begin typing System Settings. 2 Click or touch System Settings. The System Settings screen appears.
Utilities System Settings 115 ❖ General—Allows you to view the current BIOS version or change certain settings back to their default values ❖ ❖ Keyboard—Allows you to access the wake-on keyboard function, or to configure the function keys LAN—Allows you to set networking functions ❖ SATA—Allows you to set conditions for SATA ❖ USB—Allows you to enable CDP (Charging Downstream Port) to use rapid USB charge while the computer is powered On ❖ Sleep Utilities—Allows you to enable or disable Sleep an
Utilities Sleep Utilities Sleep Utilities This utility displays whether the “USB Sleep and Charge function” is enabled or disabled and shows the position of the USB port that supports the “USB Sleep and Charge function.” 1 To access Sleep Utilities from the Start screen begin typing System Settings. 2 Click or touch System Settings. 3 Click or touch Sleep Utilities.
Utilities Sleep Utilities NOTE 117 ❖ When “USB Sleep and Charge function” is set to Enabled, USB bus power (DC 5V) will be supplied to the compatible port even when the power of the computer is turned OFF. USB bus power (DC 5V) is similarly supplied to the external devices which are connected to the compatible ports. However, some external devices cannot be charged solely by supplying USB bus power (DC 5V).
Utilities Sleep Utilities Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag. Enabling/Disabling USB Sleep and Charge This utility can be used to enable or disable the USB Sleep and Charge function. To enable this function, select Enable. To disable this function, toggle the Enable button to the Disabled position.
Utilities Sleep Utilities 119 Alternate Mode. To select a different charging mode, use the Power supply mode drop-down list in the utility. (Sample Image) Sleep and Charge screen NOTE With certain external devices, the USB Sleep and Charge function may not work no matter which charging mode you select. In those cases, disable USB Sleep and Charge in the utility and turn the computer on to charge the device, or use a different charging device.
Utilities Function Key Function Key NOTE The Function option is disabled by default. TOSHIBA Function Key enables you to activate functions by pressing specific keys either singly or in combination with FN. Some functions show the toast notification at the edge of the screen. These settings turn notifications ON/OFF. 1 To access Function Key from the Start screen begin typing Function Key. 2 Click or touch Function Key. The Function Key screen appears.
Utilities Recovery Media Creator 121 Recovery Media Creator The Recovery Media Creator utility enables you to create recovery media that can be used to return your system to its out-of-box state, if necessary. For detailed information on using the utility to create recovery media, see “Creating recovery media” on page 47.
Utilities TOSHIBA Application Installer TOSHIBA Application Installer NOTE You must have an Internet connection to reinstall applications. The TOSHIBA Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: 1 To access TOSHIBA Application Installer from the Start screen begin typing Application Installer. 2 Click or touch TOSHIBA Application Installer.
Chapter 6 If Something Goes Wrong Some problems you may encounter when using your computer are relatively easy to identify and solve. Others may require help from your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
If Something Goes Wrong Problems when you turn on the computer If you are working in a program that suddenly freezes, chances are the program has stopped responding. You can exit the program without shutting down the operating system or closing other programs. To close a program that has stopped responding: 1 Press Ctrl, Alt, and Del simultaneously (once), and then click or touch Task Manager. The Task Manager window appears.
If Something Goes Wrong Problems when you turn on the computer 125 The computer displays the WARNING RESUME FAILURE/Windows Error Recovery – Windows did not shut down successfully message. To continue, select Start Windows normally. This can happen if the computer was put into Sleep mode and the battery has discharged. If you performed a shutdown before this message was displayed, a program or driver may have prevented Windows® from shutting down. Data stored in the computer’s memory has been lost.
If Something Goes Wrong The Windows® operating system is not working 3 If your computer has a removable battery, connect the AC adaptor to the computer. Leave the battery out of the computer. Try turning the computer on again. If the computer starts normally, the battery may need charging, may be depleted, or may be defective.
If Something Goes Wrong The Windows® operating system is not working 127 Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device. If you experience any of these problems, use the options in the Startup menu to fix the problem. Using Startup options to fix problems If the operating system fails to start properly, you may need to troubleshoot the Operating System and/or its settings.
If Something Goes Wrong The Windows® operating system is not working Reset your computer ❖ All of your personal files and apps are removed ❖ Your computer settings are changed back to their defaults For more information, see “Reset your PC” on page 53. Advanced options Choosing this option presents you with another set of options: System Restore ❖ System Restore allows you to use a Restore point to return the computer to a state at which it was performing properly.
If Something Goes Wrong The Windows® operating system is not working ❖ 129 Enable boot logging Creates a file that lists all the drivers that are installed during startup ❖ Enable Safe Mode Starts Windows® with a minimal set of drivers and services. If the computer starts and runs in Safe Mode, you will know the Operating System is most likely working properly and that you should look to third-party applications or drivers for the source of your problem.
If Something Goes Wrong Fixing a problem with Device Manager The Windows® operating system can help you If the operating system has started properly but you still have a problem using your computer, the online Help can assist you in troubleshooting the problem. Getting to the online Help will differ depending on which interface you are in: ❖ Start screen—Type Help and Support NOTE ❖ As soon as you begin typing, the search feature automatically begins.
If Something Goes Wrong Power and the batteries 2 131 Click or touch Device Manager. The Device Manager screen appears. 3 From the list of device(s), double-click or touch the device type. 4 To view the device(s) installed, double-click or touch the device. The operating system displays the device Properties dialog box, which provides an array of tabs. They may include: ❖ The General tab, which provides basic information about the device.
If Something Goes Wrong Power and the batteries Here are some typical problems and how to solve them: The AC power light does not come on when you plug in the AC adaptor and power cord/cable. Make sure the AC adaptor and power cord/cable are firmly plugged into both the wall outlet and the computer. If the AC power light still does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance.
If Something Goes Wrong Keyboard problems 133 After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries. To purchase a new battery pack, see your accessories information included with your computer, or visit the Toshiba Web site at accessories.toshiba.com. Refer to this site often to stay current on the most recent software and hardware options for your computer, and for other product information.
If Something Goes Wrong Display problems If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’s power cord/cable is firmly plugged into a working power outlet. ❖ Check that the cable connecting the external monitor to the computer is firmly attached. ❖ Try adjusting the contrast and brightness controls on the external monitor. ❖ Press F4 to make sure the display priority is not set for the built-in screen. The screen does not look correct.
If Something Goes Wrong Disk or storage drive problems 135 The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 1280 x 800 or higher. Devices that do not support this resolution will only work in Internal/External mode, and not simultaneous mode.
If Something Goes Wrong Disk or storage drive problems 5 Click or touch the Tools tab. 6 Click or touch the Check button. The Error Checking box appears. The system will alert you if you need to scan the drive. 7 Even if you do not need to scan the drive for errors you can scan by clicking or touching Scan drive. Error-checking tests and repairs the storage drive. Your hard disk seems very slow. If you have been using your computer for a long time, your files may have become fragmented.
If Something Goes Wrong Optical disc drive problems 137 Optical disc drive problems You cannot access a disc in the drive. If the optical disc drive is an external drive, make sure the two USB cables or the AC adaptor cable are properly connected to the computer and refer to the documentation that came with your drive. Make sure the tray that holds the optical disc is closed properly. Press gently until it clicks into place. Open the tray and remove the disc. Make sure the tray is clean.
If Something Goes Wrong Sound system problems If the problem is with an optical data disc, refer to the software’s documentation and check that the hardware configuration meets the program’s needs. The disc will not come out of the drive when you click the eject button on the screen. Press the button on the optical disc drive itself. For additional information see “You press the disc eject button, but the drive tray does not slide out.” on page 137.
If Something Goes Wrong Wireless networking problems 139 You may have connected the printer while the computer is on. Disable Sleep mode, turn off the computer, and turn off the printer. Turn the printer back on, make sure it is online, and then turn the computer back on. Try printing another file. For example, you could create and attempt to print a short test file using Notepad. If a Notepad file prints correctly, the problem may be in your original file.
If Something Goes Wrong Wireless networking problems ❖ If another computer is on the same network, verify that it has network access, and can connect to the Internet. If, for example, the other computer cannot browse to a public Web site, the ISP’s (Internet Service Provider) service may be disrupted. ❖ Verify that the Service Set Identifier (SSID), or network name, is correct - i.e., that it matches the SSID assigned to the access point you are attempting to connect through.
If Something Goes Wrong DVD operating problems ❖ 141 If you have enabled any security provisions (closed system, MAC address filtering, Wired Equivalent Privacy [WEP], etc.), check the access point vendor's Web site for recent firmware upgrades. Problems with WEP keys, in particular, are frequently addressed in new firmware releases. DVD operating problems If you experience a problem playing DVDs, you may be able to fix the problem yourself.
If Something Goes Wrong Develop good computing habits 3 To keep the display from turning off, click or touch Never in both drop down lists. 4 Click or touch Save changes. The screen saver runs while you are watching a movie or title. If the screen saver is enabled, it runs on top of any movie or title you are watching. To disable the screen saver: 1 Right-click the desktop and click or touch Personalize in the menu. 2 Click or touch Screen Saver in the lower-right corner of the window.
If Something Goes Wrong Develop good computing habits 143 Read the documentation. It is very difficult to provide a fail-safe set of steps you can follow every time you experience a problem with the computer. Your ability to solve problems will improve as you learn about how the computer and its software work together. Get familiar with all of the documentation provided with your computer, as well as the information that may come with the programs and devices you purchase.
If Something Goes Wrong Develop good computing habits 3 In the left pane, click or touch System Protection. The System Protection tab of the System Properties window appears. 4 Click or touch Configure. 5 Under Restore settings select Turn on System Protection. 6 Click or touch OK. 7 Click or touch Create. 8 In the input field, enter a name that is descriptive enough to be easily understood in the future, such as “Before installing Brand X Accounting app.” Then click or touch Create.
If Something Goes Wrong Develop good computing habits 145 7 Verify that the Restore point you chose is the correct one. If it is not, click or touch Back to return to the previous step. 8 Close all programs and save all open files. 9 Click or touch Finish, and then Yes to begin the system restore. Your Windows® operating system configuration will now be restored to the state it was in when the chosen restore point was created, and then the computer will be automatically restarted.
If Something Goes Wrong Develop good computing habits For additional Help, while in the Windows® Desktop screen, press the F1 key to launch the Windows® Help and Support screen. Search for “back up files”. General tips for installing hardware and software Here are a few tips to help ensure safe and easy installation of new hardware (printers, pointing devices, external hard drives, optical disc drive writers, scanners, etc.
If Something Goes Wrong Develop good computing habits ❖ 147 Do one installation at a time. If you have several new items to add to your computer system, install just one at a time, creating restore points immediately before each successive installation. This will make it much easier to determine the origin of any new problems. For best results, follow this sequence: 1 Back up critical data. 2 Create a restore point. 3 Install one item of hardware or software.
If Something Goes Wrong If you need further assistance ❖ If you are attempting to charge a device without an AC adaptor connected to the computer, the computer's battery power may be below the limit specified in the TOSHIBA Sleep utility or the battery may be depleted. Lower the limit in Sleep and Charge to enable charging at the current battery power level, or, if battery power is running low or is depleted, connect the AC adaptor to your computer.
If Something Goes Wrong Other Toshiba Internet Web sites 149 Contacting Toshiba Toshiba’s Technical Support Web site For technical support, or to stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at support.toshiba.com. Other Toshiba Internet Web sites toshiba.com Toshiba corporate site toshiba.com/us Marketing and product information in the USA accessories.toshiba.
If Something Goes Wrong Toshiba’s worldwide offices Italy Japan Centro Direzionale Colleoni Palazzo Perseo Via Paracelso 10 20041, Agrate Brianza Milano, Italy Toshiba Corporation, PCO-IO 1-1, Shibaura 1-Chome Minato-Ku, Tokyo, 105-8001 Japan Latin America and Caribbean Mexico Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF.
Appendix A TOSHIBA Function Keys TOSHIBA Function keys provide a quick way to modify selected system functions and to launch applications. Functions TOSHIBA Function keys are used to set or modify the following system functions: ❖ Search ❖ Brightness control ❖ Output (Display switch) ❖ Touch pad ❖ Media buttons ❖ Volume mute ❖ Wireless ❖ Zoom In/Out ❖ Keyboard Backlight ❖ Zoom (Display resolution) 151 5.375 x 8.375 ver 2.
TOSHIBA Function Keys Functions Search This TOSHIBA Function key launches the Search function. Display brightness This TOSHIBA Function key decreases the screen brightness. This TOSHIBA Function key increases the screen brightness. 5.375 x 8.375 ver 2.
TOSHIBA Function Keys Functions 153 Output (Display switch) This TOSHIBA Function key cycles through the display options and highlights the available options. (Only the first option is available when you do not have an external monitor attached.
TOSHIBA Function Keys Functions Disabling or enabling the touch pad This TOSHIBA Function key enables/disables the touch pad. To enable/disable the touch pad press F5. For more information on using the touch pad, see “Using the touch pad” on page 57. Media buttons This TOSHIBA Function key allows you to restart playing the current track or go to the previous track. This TOSHIBA Function key allows you to start playing or pause the media currently playing.
TOSHIBA Function Keys Functions 155 Disabling or enabling wireless devices This TOSHIBA Function key enables/disables the Wi-Fi® antenna in your computer. The wireless modes are: ❖ Disables the wireless antenna (Airplane mode is ON). ❖ Enables the wireless antenna (Airplane mode is OFF). Zoom In/Out This TOSHIBA Function key allows you to zoom out. This TOSHIBA Function key allows you to zoom in. Keyboard Backlight This TOSHIBA Function key enables/disables the keyboard backlight.
Appendix B Power Cord/Cable Connectors Your computer ships with the correct power supply for the country of purchase. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA Canada UL approved CSA approved United Kingdom Europe VDA approved NEMKO approved BS approved Australia AS approved 156 5.375 x 8.375 ver 2.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this User’s Guide.
Glossary DPI Dots Per Inch DVD Digital Versatile (or Video) Disc DVD-ROM Digital Versatile (or Video) Disc Read-Only Memory eSATA external Serial Advanced Technology Attachment FAT File Allocation Table FCC Federal Communications Commission GB gigabyte GBps gigabytes per second HDD Hard Disk Drive HDMI High-Definition Multimedia Interface HDMI CEC High-Definition Multimedia Interface Consumer Electronics Control HTML Hypertext Markup Language IEEE Institute of Electrical and Ele
Glossary 159 SD Secure Digital SDRAM Synchronous Dynamic Random Access Memory SSD Solid State Drive TFT Thin Film Transistor USB Universal Serial Bus URL Uniform Resource Locator WAN Wide Area Network www World Wide Web Terms The following terms may appear in this User’s Guide. A active-matrix display—A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology.
B Glossary backup—A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged. Basic Input/Output System (BIOS)—See BIOS. baud rate—The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second.
Glossary C 161 cache—A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer’s main memory. See also CPU cache, L1 cache, L2 cache. CD—An individual compact disc. See also CD-ROM. CD-ROM (Compact Disc Read-Only Memory)—A form of high-capacity storage that uses laser optics instead of magnetic means for reading data. See also CD. Compare DVD-ROM.
Glossary controller—A device that controls the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and printers all require controllers. CPU—See Central Processing Unit (CPU). CPU cache—A section of very fast memory residing between the CPU and the computer’s main memory that temporarily stores data and instructions the CPU will need to execute commands and programs. See also cache, L1 cache, L2 cache.
Glossary 163 disc—A round, flat piece of material, designed to be read from and written to by optical (laser) technology, and used in the production of optical discs, such as CDs and DVDs. Compare disk. disk—A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as hard disks. Compare disc. See also hard disk.
E Glossary emulation—A technique in which a device or program imitates another device or program. enable—To turn on a computer option. See also disable. eSATA—An external device that supports hot swapping and fast data transfer. Very useful in storing and transferring large files. executable file—A computer program that is ready to run. Application programs and batch files are examples of executable files. Names of executable files usually end with a .bat or .exe extension.
Glossary 165 frontside bus—The primary pathway (bus) between the CPU and the computer’s main memory. Also called “system bus.” See also bus. Function key—(1) A feature in which certain keys in combination with the FN key can set system options or control system parameters, such as the battery save mode. (2) A key or combination of keys that activates a memory resident program. function keys—The keys labeled F1 through F12, typically located on the keyboard.
Glossary hot swapping—The ability to add or remove devices from a computer while the computer is running and have the operating system automatically recognize the change. I icon—A small image displayed on the screen that represents a function, file, or program. interlaced—A method of refreshing a computer screen, in which only every other line of pixels is refreshed. Interlaced monitors take two passes to create a complete screen image. Compare non-interlaced. internal device—See device.
Glossary 167 LCD (Liquid Crystal Display)—A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter over the electrodes permits only non-polarized light to pass to the surface of the display, creating light and dark pixels.
N Glossary network—A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail. non-interlaced—A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen. Compare interlaced.
Glossary 169 Plug and Play—Generally, refers to the computer’s ability to automatically configure itself to work with peripheral devices. When capitalized, refers to a standard that, when followed by a device manufacturer, allows a computer to configure itself automatically to work with the device. pointer—An icon (usually an arrow) that moves on the screen when you slide your finger across the touch pad or move a mouse.
Glossary resolution—A measure of the sharpness of the images that can be produced by a printer or displayed on a screen. For a printer, resolution is expressed in dots per inch (dpi). For a screen, it is expressed as the number of pixels available horizontally and vertically. restart—Synonymous with reboot. To reset the computer by reloading the operating system without turning the computer off. See also boot.
Glossary 171 Start screen—Displays the new Windows® operating system look and feel. Suspend—A feature of some Windows® operating systems that allows you to turn off the computer without exiting your open applications and to continue from where you left off when you turn the computer on again. Swipe—Swipe an open window to the left or right of the screen to display the next or previous window.
W Glossary Web—See World Wide Web. Wi-Fi®—A registered trademark term of the Wi-Fi Alliance that stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www)—The worldwide network of Web sites linked together over the Internet. A user of the Web can jump from site to site regardless of the location of the computer hosting the site. See also Internet.
Index A AC adaptor 40 AC power 81 AC power light 40 accessing network 102 adding memory 46 optional external devices 46 adequate ventilation cooling fan 39 adjusting touch pad settings 59 Advanced Startup options 127 app, starting 71 App, starting from Start screen 72 apps starting from Start screen 72 audio features 102 B backing up files 67, 73 Backlit keyboard 69 battery battery life 80 Call2Recycle™ 94 care 92, 93 changing 89 charge indicator light 41 charge time 81 charger 81 charging 42, 81 charging
Index running computer on battery power 79 safety precautions 92 setting notifications 85 taking care of 92 battery indicator light 84 BIOS Setup see System Settings button eject, optical disc drive 74 mute button 75 next track button 75 play/pause button 75 previous track button 75 volume increase/decrease buttons 75 buttons media control buttons 75 C Call2Recycle™ battery 94 caring for your computer 63 changing battery 89 charging the battery 42 cleaning the computer 64 communications set up 101 co
Index removing with computer on 77 DVD player troubleshooting 141 DVDs using 73 E eco power plan 88 eco Utility® 108 eject button optical disc drive 74 eject, optical disc drive 74 enabling touch pad 60 enabling/disabling touch pad 154 ENERGY STAR® 26 exploring desktop 98 Start screen 96 external display device HDMI™ Out port 61 external display, adjusting 63 F files backing up 67, 73 saving 72 Function Key 120 Function Keys disabling or enabling wireless devices 155 Function keys 154 display brightness
Index previous track button 75 using 75 volume increase/decrease buttons 75 memory adding 46 Memory card reader inserting memory media 105 removing memory media 105 using 104 microphone using 102 monitor problems troubleshooting 134 monitoring battery power 83 mouse properties 71 moving the computer 64 N network accessing 102 connecting your computer 102 networking wireless 101 notification area 100 notifications 100 O online resources Toshiba 78 optical disc Auto-Run feature 76 handling 76 insertin
Index selecting power plan options 87 power saving options 86 precautions safety 37 printer troubleshooting 138 problem solving contacting Toshiba 149 Startup options 127 R real-time clock (RTC) battery 81 recording sounds 102 recovery creating recovery media 47 installing drivers and applications 56 internal storage drive 46 refresh your PC 51 reset your PC 53 restoring from recovery media 50 Recovery Media Creator 121 recycle bin icon 99 refresh your PC with user’s data 51 registering computer 43 removi
Index Reset your computer 128 supervisor password, deleting 111 supervisor password, set up 109 system indicator lights AC power 40 drive in-use indicator 74 LEDs 41, 42, 83, 84, 104 System Settings 114 T taking care of battery 92 taskbar 99 television adjusting display 63 Tiles Start screen 98 tips for computing 66 Toshiba online resources 78 registering computer Toshiba Web site 43 worldwide offices 149 TOSHIBA Application Installer 122 TOSHIBA Function key zooming in 155 zooming out 155 TOSHIBA Fu
Index U USB Sleep and Charge cannot use 147 USB Wakeup function does not work 148 user password, deleting 113 user password, setting 111 using a microphone 102 computer lock 64 DVDs 73 eco power plan 88 Memory card reader 104 optical disc drive 73 touch pad 57 Web Camera 104 using the keyboard 67 Utilities 107 V video projector adjusting display 63 W warranty standard limited warranty 30 Web Camera using 104 Web sites 149 Wi-Fi® wireless networking 101 Windows® Charms Devices 97 Search 97 Settings 97 Sha