User’s Manual Satellite L640/L640D/L645/L645D Satellite Pro L640/L640D/L645/L645D Series
Table of Contents Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii EU Declaration of Conformity . . . . . . . . . . . . . . . .
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Chapter 2 The Grand Tour Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Password Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Starting the computer by password . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 Panel power on/off . . . . . .
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Copy Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Copyright © 2010 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Memory Stick and Memory Stick PRO are trademarks or registered trademarks of Sony Corporation. WinDVD is a trademark of the Corel Corporations. DVD MovieFactory is a trademark of the Corel Corporations. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Labelflash is a trademark of YAMAHA CORPORATION. ConfigFree is a trademark of TOSHIBA Corporation.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Contact Address: Telephone: TOSHIBA America Information Systems, Inc.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Working environment This product was designed to fulfil the EMC (Electromagnetic Compatibility) requirements to be observed for so-called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments".
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Modem warning notice This information is applicable to the models equipped with a built-in modem. Conformity Statement The equipment has been approved to [Commission Decision "CTR21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN).
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer. Japan’s Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ■ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Following information is only valid for EU-member States: Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres. The black bar indicates that the product was placed on the market after August 13, 2005.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series REACH - Compliance Statement The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. TOSHIBA will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation. Please consult the following website www.toshiba-europe.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series TEAC ■ DVD Super Multi with Double Layer Recording DV-W28S JUNE 24, 2007 User’s Manual xix
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Panasonic System Networks ■ DVD Super Multi UJ890 ■ BD-Combo UJ141 ■ BD-Writer UJ240 Panasonic System Networks Co., Ltd. HITACHI-LG Data Storage, Inc. ■ DVD Super Multi GT30N/GT30F Hitachi-LG Data Storage, Inc.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series TOSHIBA SAMSUNG STORAGE TECHNOLOGY ■ DVD Super Multi TS-L633C/TS-L633Y TOSHIBA SAMSUNG STORAGE TECHNOLOGY KOREA CORPORATION 416, MEATAN-3 DONG, YEONGTONG-GU, SUWON CITY, GYEONGGI, 443-742, KOREA Precautions CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT."To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
Preface Congratulations on your purchase of the Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D series computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D computer.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Icons Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on. Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Terminology This term is defined in this document as follows: User’s Manual Start The word "Start" refers to the " Windows 7. " button in HDD or Hard disk drive Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive. In this manual, the word "HDD" or "Hard disk drive" also refers to the SSD unless otherwise stated.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series To keep your computer in prime operating condition, protect your work area from: ■ Dust, moisture, and direct sunlight. ■ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ■ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ■ Extreme heat, cold, or humidity.
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Mobile phones Please be aware that the use of mobile phones can interfere with the audio system. The operation of the computer will not be impaired in any way, but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use.
Chapter 1 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Getting Started ■ ■ ■ ■ ■ ■ ■ TOSHIBA Recovery Media Creator TOSHIBA DVD PLAYER (Is preinstalled with some models) WinDVD BD for TOSHIBA (Is preinstalled with some models) TOSHIBA Assist TOSHIBA ConfigFree™ TOSHIBA Disc Creator Corel DVD MovieFacotry for TOSHIBA (Is preinstalled with some models) ■ Corel Label@Once (Is preinstalled with some models.
Getting Started ■ Restoring the pre-installed software from the Recovery hard disk drive ■ Restoring the pre-installed software from your created Recovery Media ■ Use a virus-check program and make sure it is updated regularly. ■ Never format storage media without checking its content - formatting destroys all stored data. ■ It is a good idea to periodically back up the internal hard disk drive or other main storage device to external media.
Getting Started ■ Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.
Getting Started 1. Connect the power cord to the AC adaptor. Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on the right of the computer. 1 2 1. DC IN 19V jack 2. DC output plug Figure 1-3 Connecting the DC output plug to the computer 3.
Getting Started Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity. 1 1. Display panel Figure 1-4 Opening the display panel Use reasonable care when opening and closing the display panel.
Getting Started Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-Up Modes for more information. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Please refer to the section Starting up for the first time for more information. ■ Volume cannot be adjusted during Windows Setup. 1.
Getting Started Turning off the power The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode. Shut Down Mode When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on. 1. If you have entered data, either save it to the hard disk drive or to other storage media. 2.
Getting Started ■ Before entering Sleep Mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Sleep Mode. The computer or the memory module could be damaged. ■ Do not remove the battery pack while the computer is in Sleep Mode (unless the computer is connected to an AC power source). Data in memory could be lost.
Getting Started When you turn the power back on, you can continue where you left when you shut down the computer. ■ When the computer is in Sleep Mode, the power indicator will blink amber. ■ If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off into Hibernation Mode - Sleep Mode will consume more power while the computer is off.
Getting Started Starting Hibernation Mode You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, The Keyboard, for further details. To enter Hibernation Mode, follow the steps below. 1. Click Start. 2. Point to the arrow icon ( from the menu. ) and then select Hibernate Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid.
Getting Started ■ Press the power button and hold it down for five seconds. Once the computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button. System Recovery Options There is a hidden partition allocated on the hard disk drive for the System Recovery Options. This partition stores files which can be used to repair the system in the event of a problem.
Getting Started ■ Be sure to connect the AC adaptor when you create Recovery Media. ■ Be sure to close all other software programs except the Recovery Media Creator. ■ Do not run software such as screen savers which can put a heavy load on the CPU. ■ Operate the computer at full power. ■ Do not use power-saving features. ■ Do not write to the media when the virus check software is running.
Getting Started Restoring the pre-installed software from the Recovery hard disk drive A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem. If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.
Getting Started When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Load the Recovery Media into the computer and turn off the computer's power. 2. While holding down F12 key on the keyboard, turn on your computer when the TOSHIBA Leading Innovation >>> logo screen appears, release the F12 key. 3. Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media.
Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix G. Please handle your computer carefully to avoid scratching or damaging the surface.
The Grand Tour System indicators These LED indicators allow you to monitor the status of various computer functions and are described in more detail within the System indicators section. Bridge media slot This slot lets you insert an SD™/SDHC™/SDXC™ memory card, miniSD™/microSD™ Card, Memory Stick™ (PRO™) and MultiMediaCard™. Refer to the Optional devices section in Chapter 3, Hardware, Utilities and Options.
The Grand Tour ■ Connection to any communication line other than an analog phone line could cause a computer system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). ■ Never connect the built-in modem to a key telephone system for residences or offices.
The Grand Tour eSATA/USB combo port One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on the left hand side of the computer. This port has eSATA (External Serial ATA) function. Universal Serial Bus (USB 2.0) ports Universal Serial Bus port, which comply to the USB 2.0 standard. Keep foreign metal objects, such as screws, staples and paper clips, out of the eSATA/USB combo port or Universal Serial Bus port.
The Grand Tour Back External monitor port This port provides 15-pin, analog VGA port. This port allows you to connect an external monitor to the computer. DC IN 19V jack The AC adaptor connects to this jack in order to power the computer and charge its internal batteries. Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase - using the wrong AC adaptor can cause damage to the computer. The following figure shows the computer’s back. 1 1.
The Grand Tour Underside The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage. 3 1 1. Battery lock 2. Battery release latch 2 3. Memory module slot Figure 2-5 The underside of the computer User’s Manual Battery lock Slide the battery lock to release the battery pack ready for removal.
The Grand Tour Front with the display open This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you. 1 2 3 4 16 15 5 6 14 7 13 8 12 9 10 11 Figure 2-6 The front of the computer with the display panel open 1. Microphone* 2. Web Camera LED* 3. Web Camera* 4. Wireless LAN and Wireless WAN antennas (Not shown) 5. Display hinges 6. Stereo speaker(Right) 7. Keyboard 8.
The Grand Tour User’s Manual Microphone A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 4, Operating Basics for more information. Some models are equipped with a built-in microphone. Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your computer.
The Grand Tour Touch Pad The Touch Pad located in the palm rest is used to control the movement of the on-screen pointer. For more information, please refer to the Using the Touch Pad section in Chapter 4, Operating Basics. Touch Pad control buttons The control buttons located below the Touch Pad allow you to select menu items or manipulate text and graphics as designated by the on-screen pointer. Bluetooth antenna Some computers in this series are equipped with a Bluetooth antenna.
The Grand Tour Indicators This section explains indicator functions. System indicators LED system indicators next to their respective icons, glow when specific computer operations are in progress. Figure 2-7 System indicators User’s Manual DC IN The DC IN indicator normally glows white when power is being correctly supplied from the AC power adaptor. However, if the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will flash amber.
The Grand Tour Keyboard indicators The following figure shows the position of the CAPS LOCK indicator which shows the following conditions: ■ When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed. 1 1. CAPS LOCK indicator Figure 2-8 Keyboard indicators CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. Optical disc drives The computer may be installed with a DVD Super Multi, BD-Writer or BDCombo drive.
The Grand Tour 2 Japan, Europe, South Africa, Middle East 3 Southeast Asia, East Asia 4 Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6 China Region codes for BD drives and media BD drives and their associated media are manufactured according to the specifications of three marketing regions. Region codes can be set from WinDVD BD ([Region] tab in [Setup] dialogue).
The Grand Tour BDs ■ BD-R discs can be written only once. The recorded data cannot be erased or changed. ■ BD-RE discs can be recorded more than once. BD-Writer drive The full-size BD-Writer drive module lets you record data to rewritable CD/DVD/BDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/DVD/BDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour BD-Combo drive The full-size BD-Combo drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/DVD/BDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost all country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and to the computer. Please refer to Chapter 6, Power and Power-Up Modes for further information.
Chapter 3 Hardware, Utilities and Options Hardware This section describes the hardware of your computer. The actual specifications may vary depending on the model you purchased. Processor CPU Your computer is equipped with one processor and processor type varies depending on model. To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start -> All Programs -> TOSHIBA -> Utilities -> PC Diagnostic Tool.
Hardware, Utilities and Options Memory Memory slots 1 GB, 2 GB or 4 GB memory modules can be installed in the computer's two memory slots for a maximum of 8 GB system memory. This computer can be equipped with memory modules of a maximum size of 8 GB. The actual amount of useable system memory will be less than the installed memory modules. Video RAM The memory in a computer's graphics adaptor, used to store the image displayed on a bitmap display.
Hardware, Utilities and Options Legal Footnote (Battery Life) For more information regarding Battery Life, please refer to the Legal Footnotes section in Appendix G. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure.
Hardware, Utilities and Options ■ In this manual, the word "HDD" or "Hard disk drive" also refers to the SSD unless otherwise stated. ■ SSD is a large-capacity storage media which uses Solid-State Memory in place of a magnetic disk of the hard disk. Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors.
Hardware, Utilities and Options To access this control panel in one of the following ways: ■ Click Start -> Control Panel. Select Large icons or Small icons in View by, and then click Intel(R) Graphics and Media. ■ Right-click on the desktop and click Graphics Properties.... In this control panel, 1. Click Power and then click Power Features. 2. Select On battery from the drop-down menu in Graphics Power Plan Settings and then select the Display Power Saving Technology check box.
Hardware, Utilities and Options Sound Sound system The integrated sound system provides support for the computer's internal speakers and microphone, as allowing an external microphone and headphones to be connected via the appropriate jacks. Multimedia Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger.
Hardware, Utilities and Options Bluetooth Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers, printers and mobile phones. When it is enabled, Bluetooth provides the wireless personal area network environment which is safe and trustworthy, that is quick and easy.
Hardware, Utilities and Options System automatic Sleep/Hibernation Mode *1 This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer.
Hardware, Utilities and Options Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software. The contents of main memory are automatically saved to the hard disk drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the Turning off the power section in Chapter 1, Getting Started, for more details.
Hardware, Utilities and Options User’s Manual TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features of more various power supply managements. TOSHIBA Zooming Utility This utility allows you to enlarge or reduce the icon size on the Windows Desktop, or the zoom factor associated with specific supported applications.
Hardware, Utilities and Options TOSHIBA DVD PLAYER This software is provided for playback of DVDVideo. It has an on-screen interface and functions. Click Start -> All Programs -> TOSHIBA DVD PLAYER -> TOSHIBA DVD PLAYER. For more information, please refer to the TOSHIBA DVD PLAYER section in Chapter 4, Operating Basics. Bluetooth Stack for Windows by TOSHIBA This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones.
Hardware, Utilities and Options WinDVD BD for TOSHIBA This software is provided for playback of Blu-ray disc. It has an on-screen interface and functions. To start this utility, click Start -> All Programs -> Corel -> Corel WinDVD BD. TOSHIBA HDD/SSD Alert Utility This utility includes wizard functions to monitor the Disk Drive operating status and execute the system backup. To access the utility, click Start -> All Programs -> TOSHIBA -> Utilities -> HDD SSD Alert.
Hardware, Utilities and Options Corel DVD MovieFactory for TOSHIBA Corel DVD MovieFactory for TOSHIBA allows users to instantly create Blu-ray disc movie, DVD video or slideshow discs via a user-friendly wizard interface with specific task oriented features. The LabelflashTM feature is also supported which allows text and images to be printed on the label surface of Labelflash compatible media without using a printer.
Hardware, Utilities and Options User’s Manual TOSHIBA eco Utility This PC is equipped with "eco mode". This mode slightly lowers performance of some devices to reduce electric power consumption. You can realize measurable power savings by using it continuously. TOSHIBA eco Utility helps you monitor your power savings by showing approximate real time power consumption.
Hardware, Utilities and Options TOSHIBA Media Controller This application allows you to control your music, pictures and videos by streaming content to any compatible device in your home. To access this utility, click Start -> All Programs -> TOSHIBA -> TOSHIBA Media Controller -> TOSHIBA Media Controller. For more information, please refer to the TOSHIBA Media Controller Help.
Hardware, Utilities and Options Bridge media slot The computer is equipped with a Bridge media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants. ■ Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or Keyboard.
Hardware, Utilities and Options Memory media This section provides the important safety precautions in order to handle your memory media. Points to note about the SD/SDHC/SDXC memory card SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music.
Hardware, Utilities and Options Media care Observe the following precautions when handling the card. Card care ■ Do not twist or bend cards. ■ Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid. ■ Do not touch the metal part of a card or expose it to liquids or let it get dirty. ■ After using card, return it to its case. ■ The card is designed so that it can be inserted only one way. Do not try to force the card into the slot.
Hardware, Utilities and Options 3. Press the memory media gently to ensure a firm connection is made. 1 2 1. Bridge media slot 2. Memory media Figure 3-2 Inserting a memory media ■ Make sure memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it. ■ When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data.
Hardware, Utilities and Options ■ Make sure the Bridge Media slot indicator is off before you remove the memory media or turn off the computer’s power. If you remove the memory media or turn off the power while the computer is accessing the memory media, you may lose data or damage the media. ■ Do not remove the memory media while the computer is in Sleep or Hibernation Mode. The computer could become unstable or data in the memory media could be lost.
Hardware, Utilities and Options Installing a memory module To install a memory module, follow the steps as detailed below: 1. Shut down the computer - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required). 2. Remove the AC adaptor and all cables and peripherals connected to the computer. 3. Close the display panel. 4.
Hardware, Utilities and Options 7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 45 degree angle before holding it down until the latches on either side snap into place. 3 1 2 1. Notch 3. Slot B 2. Slot A Figure 3-5 Seating the memory module ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer.
Hardware, Utilities and Options 1 2 1. Memory module cover 2. Screws Figure 3-6 Seating the memory module cover 9. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required. 10. Turn your computer over. 11. Turn the computer on and make sure the added memory is recognized to confirmed it, Start -> Control Panel -> System and Security -> System icon.
Hardware, Utilities and Options 8. Grasp the module by its edges and remove it from the computer. ■ If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 1 1.
Hardware, Utilities and Options External monitor An external analog monitor can be connected to the external monitor port on the computer. To connect a monitor, follow the steps as detailed below: Connecting the monitor cable 1. Turn the computer's power off. 2. Connect the monitor cable to the external monitor port. 1 2 1. External monitor port 2. Monitor cable Figure 3-8 Connecting the monitor cable to the external monitor port 3. Turn the external monitor's power on. 4.
Hardware, Utilities and Options eSATA (External Serial ATA) An device corresponding to eSATA function can be connected to the eSATA/USB combo port on the computer. Connecting the eSATA device To connect an eSATA device, follow the steps as detailed below: 1. Connect an eSATA cable to the eSATA/USB combo port. Make sure the connector is properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins. 2 1 1. eSATA cable 2.
Hardware, Utilities and Options 2. Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar. 3. Click an eSATA device that you want to remove. 4. Carefully pull an eSATA device's eSATA/USB combo connector out from within the computer's eSATA/USB combo port. HDMI A HDMI monitor can be connected to the HDMI out port on the computer.
Hardware, Utilities and Options ■ When you connect a television or external monitor to the HDMI port and the display output device is set to HDMI. When you unplug the HDMI cable and re-plug it in please wait at least 5 seconds before you replug the HDMI cable again. ■ When you connect a television or external monitor to the HDMI port and you connect the television, external monitor or external sound device to another port. When you change the display output or Unplug/re-plug the HDMI cable.
Hardware, Utilities and Options The above display mode is a typical HDMI display mode. The selectable display modes will vary for different HDMI monitors. Security lock A security locks enable you to anchor your computer a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot on its left side into which you can attach one end of the security cable, while the other end attaches to a desk or similar object.
Hardware, Utilities and Options Optional accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer: User’s Manual DDR31066/1333/1600 Memory Kit A 1 GB, 2 GB or 4 GB memory module (DDR31066/1333/1600) can easily be installed in the computer.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go. 3 1 2 1. Touch Pad 2. Touch Pad control buttons 3. Touch Pad ON/OFF button Figure 4-1 Touch Pad and Touch Pad control buttons Press Touch Pad ON/OFF button could enable or disable the Touch Pad function.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the item(s) you want to move, leave your finger on the Touch Pad after the second tap and then move the item(s) to their new destination. Web Camera Some models are equipped with a Web Camera. Web Camera is a device that allows you to record video or take photographs with your computer.
Operating Basics Using the TOSHIBA Face Recognition TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier. ■ TOSHIBA Face Recognition does not guarantee the correct identification of a user.
Operating Basics ■ The Registration screen is displayed for a logged-in user whose face has not been registered. ■ The Management screen is displayed for a logged-in user whose face has already been registered. 2. Click Run as administrator in lower left of the Management screen, and then click the Register button. The Registration screen is displayed. ■ If you wish to practice, click on the Next button in the Registration screen.
Operating Basics How to Delete the Face Recognition Data Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below: 1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> Face Recognition. The Management screen is displayed. 2. Select a user which is displayed in the Management screen. 3. Click the Delete button. "You are about to delete the user data.
Operating Basics 1:1 Mode Login screen 1. Turn on the computer. 2. The Select Tiles screen will be displayed. 3. Select Start face recognition ( ). 4. 5. 6. 7. The Select Account screen will be displayed. Select the account, and click the arrow button. "Please face the camera" will be displayed. Verification will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another.
Operating Basics Loading discs To load a disc, follow the steps as detailed below: 1. When the computer’s power is on, press the eject button to open the disc tray slightly. 2. Grasp the disc tray gently and pull until it is fully opened. 1 2 1. Eject button 2. Disc tray Figure 4-3 Pressing the eject button and pulling the disc tray open 3. Lay the disc, label side up, in the disc tray. 1 1.
Operating Basics ■ Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment. ■ Prevent foreign objects from entering the drive. Check the surface of the disc tray, especially the area behind the front edge of the disc tray, to make sure there are no such objects before closing the drive. 4. Press gently at the center of the disc until you feel it click into place. The disc should lie below the top of the spindle, flush with the spindle base. 5.
Operating Basics Figure 4-6 Removing a disc 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove discs when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole near the eject button. 1 Diameter 1mm 1.
Operating Basics ■ Some models in this series are equipped with a BD-Writer/BD-Combo drive which can write CD/DVD/BDs. ■ Some models in this series are equipped with a DVD Super Multi drive which can write CD/DVDs. You can use the BD-Writer drive to write data to either CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM, BD-R, BD-R (Dual Layer), BD-RE or BD-RE (Dual Layer) discs.
Operating Basics Disclaimer TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM, BD-R, BD-R (Dual Layer), BD-RE or BD-RE (Dual Layer) disc that may be caused by writing or rewriting with this product.
Operating Basics DVD-R for Labelflash: FUJIFILM CORPORATION (for 16x speed media) DVD+R: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media) DVD+R (Double Layer): MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed media) DVD+R for Labelflash: FUJIFILM CORPORATION (for 16x speed media) DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 Victor Company of Japan, Ltd. (JVC) (for 4x and 6x speed media) DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD.
Operating Basics Before writing or rewriting with the BD-Combo drive ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVDRAM, media, however, it must be noted that disc quality can affect write or rewrite success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: TAIYO YUDEN CO., Ltd.
Operating Basics DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media) DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Corporation (for 3x and 5x speed media) Hitachi Maxell,Ltd.
Operating Basics DVD+R (Double Layer): MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed media) DVD+R for Labelflash: FUJIFILM CORPORATION (for 16x speed media) DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 Victor Company of Japan, Ltd. (JVC) (for 4x and 6x speed media) MITSUBISHI KAGAKU MEDIA CO.,LTD. (for 4x and 6x speed media) DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media) DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.
Operating Basics ■ Data deleted/erased from a CD-RW, DVD-RW, DVD+RW or DVD-RAM disc cannot be recovered. You must check the content of the disc carefully before you delete it, taking care that, if multiple drives that can write data to discs are connected, you do not delete data from the wrong one.
Operating Basics ■ Always copy data from the hard disk drive to the optical media - do not use the cut-and-paste function as the original data will be lost if there is a write error. ■ Do not perform any of the following actions: ■ Change users in the Operating System. ■ Operate the computer for any other function, including such tasks as using a mouse or Touch Pad, or closing/opening the display panel. ■ Start a communication application. ■ Apply impact or vibration to the computer.
Operating Basics ■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R, DVD+R (Double Layer) or DVD+RW media using the "Disc Backup" function of TOSHIBA Disc Creator. ■ You cannot back up DVD-ROM, DVD-Video, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW to CDR or CD-RW media using the "Disc Backup" function of TOSHIBA Disc Creator. ■ TOSHIBA Disc Creator cannot record in packet format.
Operating Basics How to learn more about TOSHIBA Disc Creator Please refer to the Help files for additional TOSHIBA Disc Creator information. When Using Corel DVD MovieFactory for TOSHIBA How to make a Labelflash DVD Simplified steps for making a Labelflash DVD: 1. Insert a Labelflash disc in optical disc drive. Set PRINTING SIDE for underside. 2.
Operating Basics 3. Add source from HDD by clicking Add Video files button to invoke browser dialog box. 4. Choose the source video and then go to Next page to apply Menu. 5. After choosing the menu template, click the Next button to go to the Burning Page. 6. Choose the output type and then click the Burn button. How to learn more about Corel DVD MovieFactory Please refer to the Help and Manual files for additional Corel DVD MovieFactory information.
Operating Basics ■ Do not set the working drive to a slow device like a USB1.1 hard disk drive or it will fail to write DVD or Blu-ray disc. ■ Do not perform any of the following actions: ■ Operate the computer for any other function, including using a mouse or Touch Pad, or closing/opening the display panel. ■ Bump or cause vibration to the computer. ■ Use the Mode control button and Audio/Video control button to reproduce music or voice. ■ Open the DVD drive.
Operating Basics ■ Use DVD-Video discs with a region code which is either "the same as the factory default setting" or "ALL". ■ Do not playback DVD discs Video while watching or recording television programs using other applications. Doing so may cause DVD-Video playback or television program recording errors. In addition, if prescheduled recording starts during DVD-Video playback it may cause DVD-Video playback or television program recording errors.
Operating Basics Display Devices & Audio ■ "TOSHIBA DVD PLAYER" will only run when "Colors" is set to "True color (32 bit)". Click Start -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution, click "Advanced settings", select "Monitor" tab, set "colors" to "True color (32 bit)". ■ If the DVD-Video image is not displayed on an external display or television, stop the "TOSHIBA DVD PLAYER", and change the screen resolution.
Operating Basics 2. Select Start -> All Programs -> TOSHIBA DVD PLAYER -> TOSHIBA DVD PLAYER to start "TOSHIBA DVD PLAYER". Operating TOSHIBA DVD PLAYER Notes on Using "TOSHIBA DVD PLAYER". ■ Screen display and available features may vary amongst DVD-Videos and scenes. ■ If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, touch pad and mouse menu operations may not be able to be used.
Operating Basics ■ WinDVD BD supports AACS (Advanced Accesss Control System) copy protection technology. Renewal of the AACS key integrated into this product is required for uninterrupted enjoyment of Blu-ray Disc. An Internet connection is required for renewal. AACS key renewal is provided free of charge for 5 years after the purchase of this product, however renewal beyond 5 years is subject to conditions specified by the software provider, Corel Corporation.
Operating Basics Operating WinDVD BD for TOSHIBA Notes on Using "WinDVD BD for TOSHIBA". 1. Screen display and available features may vary amongst BD-Videos and scenes. 2. If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, touch pad and mouse menu operations may not be able to be used. Open WinDVD BD for TOSHIBA HELP WinDVD BD for TOSHIBA features and instructions are also explained in detail in "WinDVD Help". Use the following procedure to open "WinDVD Help".
Operating Basics To launch Volume Mixer, follow the steps below. 1. Locate the Speaker icon on the Taskbar. 2. Right-click the Speaker icon on theTaskbar. 3. Select Open Volume Mixer from the menu. Adjust speaker volume by moving the slider up or down under Device to raise or lower the volume of your speakers. Click the Mute button to mute the volume. You may see another control under Applications in Volume Mixer. It is the control for an application which is currently running.
Operating Basics Dolby Advanced Audio Dolby Advanced Audio provides a stunning listening experience from any pair of speakers or headphones. Adding a new level of realism to movies, music, and games, this is the quality audio customers have been missing from your computers. Dolby Advanced Audio includes: ■ High-Frequency Enhancer: Analyzes and restores high frequencies lost during encoding. Works on any speaker for a higher level of audio than was previously possible.
Operating Basics This feedback occurs repeatedly and causes a very loud, high-pitched noise. It is a common phenomenon that occurs in any sound system when the microphone input is output to the speaker (throughput) and the speaker volume is too loud or too close to the microphone. You can control throughput by adjusting the volume of your speaker or through the Mute function in the Master Volume panel. Refer to your Windows documentation for details on using the Master Volume panel.
Operating Basics 4. In the General tab, select a country or region in the Country/Region list and then click OK. 5. Click OK in the Phone and Modem window. Please check whether the region you have selected is supported by this computer. If you select a region that is not supported, local settings of the modem will default to the United States.
Operating Basics If you use a storage device such as an optical disc drive or hard disk drive connected to a 16-bit PC Card, you might experience the following problems with the operation of the modem: ■ The modem speed is slow or communication is periodically interrupted. ■ Skips or jumps may be noted in sound. Disconnecting the modular cable To disconnect the modular cable, follow the steps as detailed below: 1. Pinch the lever on the plug in the telephone jack and pull it out from within the connector.
Operating Basics ■ Frequency Channel Selection of 5GHz for IEEE 802.11a or/and IEEE802.11n ■ Frequency Channel Selection of 2.4GHz for IEEE 802.11b/g or/and IEEE802.
Operating Basics Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2.4GHz band, which is license-free and compatible with radio systems in most countries in the world. Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other.
Operating Basics Enable/Disable Wireless communication You can enable or disable Wireless communication functions by pressing FN + F8. No transmissions are sent or received when wireless communication is turned off. Wireless communication Indicator The wireless communication indicator shows the status of the computer's wireless communication functions. Indicator status Indication Indicator off The wireless communication function is off - no wireless functionality is available.
Operating Basics If you are using Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T), be sure to connect with a CAT5E cable or higher. You cannot use a CAT3 or CAT5 cable. If you are using Fast Ethernet LAN (100 megabits per second, 100BASETX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable.
Operating Basics Disconnecting the LAN cable To disconnect the LAN cable, follow the steps as detailed below: 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub or router in the same manner. Check with your LAN administrator and hardware or software vendor before disconnecting from the hub. Computer Handling This section explains computer handling and maintenance.
Operating Basics ■ Be careful not to subject the computer to impact or shock - a failure to follow this instruction could result in damage to computer, computer failure or loss of data. ■ Never transport your computer with any cards installed - this may cause damage to either the computer and/or the card resulting in product failure. ■ Always use a suitable carry case when transporting the computer. ■ When carrying your computer, be sure to hold it securely so that it does not fall or hit anything.
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer. The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with the special FN key) are the twelve keys at the top of your keyboard - these keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed and, when used in combination with the FN key, those keys marked with icons also execute specific functions on the computer.
The Keyboard , or , Press FN + F10 or FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become either cursor control keys (FN + F10) or numeric keypad keys (FN + F11) . Please refer to the Keypad overlay section in this chapter for more information on how to operate these keys, taking care to note that the power on default for both settings is off. , Press FN + F12 (ScrLock) to lock the cursor on a specific line.
The Keyboard Output: Pressing FN + F5 changes the active display device. To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. Brightness Down: Pressing FN + F6 decreases the computer's display panel brightness in individual steps. Brightness Up: Pressing FN + F7 increases the computer's display panel brightness in individual steps. Wireless: Pressing FN + F8 switches the active wireless devices.
The Keyboard TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows. Volume down: Pressing FN + 3 decreases the volume in increment . Volume up: Pressing FN + 4 increases the volume in increment. FN Sticky key You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an "F Number" key.
The Keyboard Arrow Mode To turn on Arrow Mode, press FN + F10 - you are able to access cursor and page control functions by using the keys. You are able to press FN + F10 again to turn off this overlay function. Numeric Mode To turn on Numeric Mode, press FN + F11 - you are able to access numeric characters by using the keys. You are able to press FN + F11 again to turn off this overlay function.
The Keyboard Temporarily changing modes If the computer is in Numeric Mode, you can switch temporarily to Arrow Mode by pressing a SHIFT key, while if it is in Arrow Mode, you can switch temporarily to Numeric Mode by also pressing a SHIFT key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation, but you are able to generate these characters using their specific ASCII codes. 1. Hold down ALT key. 2.
Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor, battery pack and any internal batteries. This chapter provides details on making the most effective use of these resources, and includes information on charging and changing batteries, tips for saving battery power, and information on the different power-up modes.
Power and Power-Up Modes Table 6-1 Power conditions continued Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery flashes amber DC IN off Battery charge is exhausted Computer shuts down No battery installed • No operation Power off (no operation) • LED: Battery off DC IN off Monitoring of power condition As shown in the below table, the Battery, DC I
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected - the following indicator conditions should be noted: White Indicates the AC adaptor is connected and is correctly supplying power to the computer. Flashing amber Indicates a problem with the power supply. You should initially try plugging the AC adaptor into another power outlet - if it still does not operate properly, you should contact your reseller or dealer.
Power and Power-Up Modes Real Time Clock (RTC) battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off.
Power and Power-Up Modes ■ The battery pack and high capacity battery pack are lithium ion batteries, which can explode if not replaced, used, handled or disposed of properly. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ The computer's RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative.
Power and Power-Up Modes Battery charging notice The battery may not begin charging immediately under the following conditions: ■ The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, you should charge it at room temperature of between 5° to 35°C (41° to 95°F). ■ The battery is nearly completely discharged.
Power and Power-Up Modes Maximizing battery operating time A battery's usefulness depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on: ■ Processor speed ■ Screen brightness ■ System Sleep Mode ■ System Hibernation Mode ■ Display power off period ■ Hard disk drive power off period ■ How often and for how long you use the hard disk drive and external disk(c) drives, for example, optical disc and floppy diskette drive.
Power and Power-Up Modes 4. Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power. The DC IN indicator should glow white, and the Battery indicator should glow amber to indicate that the battery pack is being charged, however, in the event that DC IN indicator does not glow this indicates that power is not being supplied - check the connections for the AC adaptor and the power cord. 5. Charge the battery pack until the Battery indicator glows white.
Power and Power-Up Modes 6. Slide and hold the battery release latch to disengage the battery pack and then remove it from the computer . 3 1 2 1. Battery pack 2. Battery lock 3.
Power and Power-Up Modes Password Utility The password utility allows you to maintain an additional level of security and provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Supervisor Password Utility are different from the Windows® login password.
Power and Power-Up Modes If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. Power-up modes The computer has three different power-up modes as follows: ■ Shut Down Mode : The computer will shut down without saving data - in view of this you must always save your work before you turn the computer off. ■ Hibernation Mode : Data in memory will be saved to the hard disk drive.
Chapter 7 HW Setup This chapter explains how to use the TOSHIBA HW Setup program to configure your computer, and provides information on settings for various functions. Accessing HW Setup To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Utilities -> HWSetup. HW Setup window The HW Setup window contains a number of tabs (General, Password, Display, Boot Priority, Keyboard, LAN, SATA and USB) to allow specific functions of the computer to be configured.
HW Setup Setup This field displays the installed BIOS version, date and EC version. Password This option allows you to set or reset the user password for power on. User Password Lets you register a new password or change/remove an existing password. Not Registered Changes or remove the password. Registered Selects the password. A dialogue box will appear to allow you to set the password. To enter a user password: 1.
HW Setup This tab lets you customize your computer’s display settings for either the internal display or an external monitor. Power On Display This tab allows you to select the display to be used when the computer is started. Please note that this setting is only available on standard VGA mode and is not available as part of the Windows Desktop properties. The Power On Display is supported with some models.
HW Setup U Selects the USB floppy diskette drive. N Selects the network. 1 Selects the built-in hard disk drive. C Selects the CD-ROM*. S Selects the USB memory. E Selects the eSATA HDD. * In this computer, CD-ROM refers to the DVD Super Multi driver, BDCombo drive or BD-Writer drive. To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. when the TOSHIBA Leading Innovation >>> screen appears, release the F12 key. 2.
HW Setup LAN Wake-up on LAN This feature lets the computer's power be turned on from shutdown when it receives a wake-up packet (Magic packet) from the LAN. Do not install or remove a memory module while Wake-up on LAN is enabled. ■ The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.
HW Setup SATA eSATA This feature allows you to set conditions for eSATA. Enabled Enables the eSATA port (Default). Disabled Disables the eSATA port in order to save power. SATA Interface setting This feature allows you to set SATA interface setting. User’s Manual Performance Let HDD/SSD work with maximum performance (Default). Battery life Let HDD/SSD work with battery life mode. If this setting is selected, this caused performance down.
Chapter 8 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Troubleshooting ■ Before you attach an external device you should first turn the computer off, then when you turn the computer back on again it will recognize the new device. ■ Make sure all optional accessories are configured properly in the computer's setup program and that all required driver software has been loaded (please refer to the documentation included with the optional accessories for further information on its installation and configuration).
Troubleshooting Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted - in these instances try loading another copy of the software if possible. If an error message appears while you are using a software package you should refer to the documentation supplied with it as this will usually include a problem solving section or a summary of error messages.
Troubleshooting Self test While booting up the computer, self test is executed automatically and the TOSHIBA logo is displayed on the screen. This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system according to how the Boot Priority option is set within the TOSHIBA HW Setup program.
Troubleshooting If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact your reseller, dealer or service provider. Computer shuts down and its DC IN indicator is flashing white This indicates a problem with the heat dispersal system - you should contact your reseller, dealer or service provider. AC power If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN indicator.
Troubleshooting Problem Procedure Check whether the battery is hot or cold to the touch - if so, it will not charge properly and should be allowed to reach room temperature before you try again. Unplug the AC adaptor and remove the battery to make sure its connecting terminals are clean - if necessary wipe them with a soft dry cloth lightly dipped in alcohol. Connect the AC adaptor and replace the battery, taking care to ensure that it is securely seated in the computer.
Troubleshooting Real Time Clock Problem Procedure The BIOS setting and system date/time are lost. The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the BIOS setup application by using the following steps: 1. Turn on the computer while pressing the F2 key. 1. Release the F2 key when the TOSHIBA Leading Innovation >>> screen appears - the BIOS setup application will load. 2. Set the date in the System Date field. 3.
Troubleshooting Internal display panel Apparent computer's display panel problems may be related to the computer's setup and configuration - please refer to Chapter 7, HW Setup, for further information. Problem Procedure No display Press the FN + F5 hot keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the These marks may have come from contact with computer's display the keyboard and Touch Pad while the display panel.
Troubleshooting Problem Procedure Slow performance The files on the hard disk drive may be fragmented - in this instance you should run the disk Defragmentation utility to check the condition of your files and the hard disk drive. Please refer to the operating system's documentation or online Help File for further information on operating and using the Defragmentation utility. As a last resort you should reformat the hard disk drive and then reload the operating system and all other files and data.
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Recordable DVD: DVD-R/-R DL, DVD+R/+R DL, DVD-RW, DVD+RW, DVD-RAM Check the region code on the DVD. It must match that on the DVD Super Multi drive. Region codes are listed in the Optical disc drives section in Chapter 2, The Grand Tour.
Troubleshooting Check the type of CD/DVD/BD you are using. The drive supports: BD-Writer/BD-Combo:BD-ROM, BD-ROM DL, BD-R, BD-R DL, BD-RE, BD-RE DL DVD-ROM: DVD-ROM, DVD-Video, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM Recordable disc: CD-R, CD-RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW, DVD-RAM, BD-R, BD-R DL, BD-RE, BD-RE DL Check the region code on the disc. It must match that on the BD drive. Region codes are listed in the Optical disc drives section in Chapter 2, The Grand Tour.
Troubleshooting Problem Procedure You cannot read a file Check to ensure the required file is actually on the Memory Card that is inserted into the computer. If you are still unable to resolve the problem, contact your reseller, dealer or service provider. Pointing device If you are using a USB mouse, you should also refer to both the USB device section in this chapter, and the documentation supplied with your mouse. Touch Pad Problem Procedure The Touch Pad does not work.
Troubleshooting Problem Procedure The reaction of Touch pad is either too sensitive or not sensitive enough. Adjust the touch Sensitivity. 1. Click Start -> Control Panel -> Hardware and Sound -> Mouse. 2. Within the Mouse Properties window, click the Advanced tab. 3. Click the Advanced feature settings... button. 4. Advanced feature settings is displayed. 5. In the Touch Pad tab, click Settings... button within the Pointer speed and tapping settings. 6. Detailed Touch Pad settings window is displayed.
Troubleshooting Problem Procedure The on-screen pointer moves too fast or too slow In this instance, you should initially try changing the speed setting within the Mouse Control utility. 1. To access this utility, click Start -> Control Panel -> Hardware and Sound -> Mouse. 2. Within the Mouse Properties window, click the Pointer Options tab. 3. Set the pointer speed as required and click OK.
Troubleshooting eSATA device In addition to the information in this section, please also refer to the documentation supplied with your eSATA device. Problem Procedure eSATA device does not work Remove the eSATA device from the computer and then reconnect it to a free port it in order to ensure it is firmly attached. A connected eSATA device may not be recognized if it is connected to the computer's eSATA/USB combo port while the computer is in Sleep Mode or Hibernation Mode.
Troubleshooting Sound system In addition to the information in this section, please also refer to the documentation supplied with your audio device. Problem Procedure No sound is heard Adjust the volume. To increase the volume click the volume up button, and to decrease it click the volume down button. Check the software volume settings. Please check to see if Mute is turned to Off Check to make sure the headphone connection is secure.
Troubleshooting Problem Procedure Press the FN + F5 hot key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected. When the external monitor is set as the primary display device in extended desktop mode, it will not display when the computer wakes up from Sleep Mode if the external monitor has been disconnected while in Sleep Mode.
Troubleshooting Problem Procedure After making a call you can’t hear a ring Ensure that the communication application's tone or pule dialling selection feature is set correctly. Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval - try lengthening this time interval within your communication application.
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication switch is set to on. If problems persist, contact your LAN administrator. Bluetooth For further information on Bluetooth wireless communication, please refer to Chapter 4, Operating Basics.
Troubleshooting If you turn the computer off into Sleep Mode while the display is on HDMI monitor, the computer will select either the internal LCD or an external computer CRT as the display device the next time is turned on. Recovery Media Problem Procedure The following message appears when executing Recovery Media Creator. "The Recovery Media Creator can not be launched because there is no recovery partition.
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: User’s Manual Outside of Europe In Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division Building C, 12-24 Talavera Rd, North Ryde, 2113, NSW, Australia. Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Refer to User Information Guide about Size.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 19V DC Built-in Modem This information is applicable to the models equipped with a built-in modem.
Specifications User’s Manual Communication speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/16 800/19200/21600/24000/26400/28800/31200/33 600 bps Data reception only with V.
Appendix B Display Controller and Video mode Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. Due to the display panel's increased resolution, lines may appear broken in when displaying images in full-screen text mode. The display controller also controls the video mode and uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed at any one time.
Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications Form Factor PCI Express Mini Card Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN module may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN module may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions. 2.4GHz Band Channels Sets (Wireless IEEE 802.11 Revision b, g and n) Frequency Range Channel ID 2400-2483.
Wireless LAN ■ In a Wireless LAN Access Point, the Wireless LAN module will use the factory-set default channel (printed in bold), unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device. 5GHz Band Channels Sets (Wireless IEEE 802.
Wireless LAN 161 5805*2 165 5825*2 *1 Factory-set default channels *2 The channel which can be used depends on the installed wireless LAN module. And the approved channels on using are different at each country or region. The channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN module will automatically start operation at the channel identified by the Wireless LAN Access Point.
Appendix D Bluetooth wireless technology Interoperability Bluetooth Adaptor from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver. 3.0+HS, as defined and approved by The Bluetooth Special Interest Group. ■ Bluetooth Specification Ver. 2.1+EDR, as defined and approved by The Bluetooth Special Interest Group.
Bluetooth wireless technology Interoperability ■ When you use Bluetooth Adaptor from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth Adaptor from TOSHIBA, always change the frequency, move your computer to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/43.74 yards or more) or stop transmitting from your computer.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Bluetooth wireless technology Interoperability Taiwan Article 12 Without permission granted by the DGT or NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to an approved low power radio-frequency devices.
Bluetooth wireless technology Interoperability 2. Indication The indication shown below appears on this equipment. (1) 2.4 : This equipment uses a frequency of 2.4 GHz. (2) FH : This equipment uses FH-SS modulation. (3) 1: The interference range of this equipment is less than 10 m. (4) This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.
Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors Denmark: DEMKO Norway: NEMKO Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 215P (250V) or 1-15P (125V) and three pin plug configuration must be 615P (250V) or 5-15P (125V) as designated in the U.S.
Appendix F TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption, battery health and the system cooling, informing you of significant system conditions. This application recognizes the system and individual component serial numbers, and will track specific activities related to the computer and their usage. The collected information includes device operation time and number of actuations or status changes (i.e.
TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA's obligations under its standard limited warranty in any way. TOSHIBA's standard limited warranty terms and limitations apply. Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started using the following methods: ■ Click Start -> All Programs -> TOSHIBA -> Utilities -> PC Health Monitor. ■ Click the icon ( ) in the notification area, then click the "Enable PC Health Monitor...
Appendix G Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis. CPU Central Processing Unit ("CPU") Performance Legal Footnotes.
Legal Footnotes ■ use of computer at temperatures outside the range of 5°C to 30°C (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your computer documentation or visit the TOSHIBA website at www.pcsupport.toshiba.com for details). CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shutdown.
Legal Footnotes Battery Life Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Legal Footnotes Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed. Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary HDD: hard disk drive HDMI: High-Definition Multimedia Interface IDE: integrated drive electronics IEEE: Institute of Electrical and Electronics Engineers I/O: input/output IRQ: interrupt request KB: kilobyte LAN: local area network LCD: liquid crystal display LED: light emitting diode MB: megabyte MMC: multi media card OCR: optical character recognition (reader) PC: personal computer PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RT
Index A D AC adaptor 3-3 DC IN 19V jack 2-5 additional 3-30 connecting 1-3 ASCII characters 5-7 DC IN indicator 2-10, 6-3 DVD MovieFactory for TOSHIBA 3-13 DVD Super Multi drive problems 8-9 Display 3-4 automatic power off 3-7 brightness down 5-4 brightness up 5-4 controller B-1 hinges 2-8 opening 1-6 screen 2-9 Documentation list 1-1 Dual Pointing Device Touch Pad 2-9, 4-1 Touch Pad control buttons 4-1 using 4-1 B BD drive problems 8-10 Battery charging 6-5 extending life 6-7 indicator 2-10, 6-2 monito
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series FN + F12 (ScrLock) 5-3 FN + F2 (Power Plan) 5-3 FN + F3 (Sleep) 5-3 FN + F4 (Hibernate) 5-3 FN + F5 (Output) 5-4 FN + F6 (Brightness Down) 5-4 FN + F7 (Brightness Up) 5-4 FN + F8 (Wireless) 5-4 FN + F9 (Touch Pad) 5-4 FN + space (Zoom) 5-4 Function keys 5-2 G Graphics controller 3-5 H HDMI 3-27 HW Setup Boot priority 7-3 LAN 7-5 SATA 7-6 USB 7-5 accessing 7-1 display 7-2 general 7-1 keyboard 7-4 window 7-1 Hard Disk Drive/Optical
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series Modem 3-6 connecting 4-30 disconnecting 4-31 jack 2-2 problems 8-17 region selection 4-29 Moving the computer 4-36 MultiMediaCard 3-16 P Password Starting the computer by 6-10 power on 3-8 Pointing Device Touch Pad 8-12 Power Hibernation Mode 1-10 Shut Down mode (Boot Mode) 1-8 Sleep Mode 1-8 System Auto Off 6-11 conditions 6-1 indicators 6-2 panel on/off 3-8, 6-11 turning off 1-8 turning on 1-7 Problems AC power 8-5 Additional mem
Satellite L640/L640D/L645/L645D/Satellite Pro L640/L640D/L645/L645D Series U USB device problems 8-14 Using WinDVD BD for TOSHIBA 4-24 Utilities and Applications 3-9 V Video RAM 3-2 Video mode B-1 W Web Camera 2-8, 3-6, 4-2 Wireless LAN 3-7, 4-31 problems 8-19 Wireless communication 4-31 indicator 2-10, 4-34 Z eSATA device 3-26 eSATA/USB combo port 2-4 problems 8-15 User’s Manual Index-4
