TOSHIBA Satellite A210/ Satellite Pro A210 Portable Personal Computer User’s Manual
Copyright © 2007 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Bluetooth is a registered trademark owned by its proprietor and used by TOSHIBA under license. DVD MovieFactory is trademarks of the Ulead Systems. Inc. Labelflash™ is a trademark of YAMAHA CORPORATION. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. U.S. Pat. No's.
resulting excessive current follow can cause extremely high temperatures and may result in damage from burns. ❑ Be sure that noting rests on your AC adapter’s power cable and that the cable is not located where it can be tripped over or stepped on. ❑ Place the AC adapter in a ventilated area, such as a desk top or on the floor, when you use it to run the computer or to charge the battery.
mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ❑ Reorient or relocate the receiving antenna. ❑ Increase the separation between the equipment and receiver. ❑ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ❑ Consult the dealer or an experienced radio/TV technician for help..
BSMI Notice (Taiwan Only) EU Declaration of Conformity Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 2006/95/EC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/5/EC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Cet appareil numérique de la class B respecte toutes les exgences du Règlement sur le matériel brouileur du Canada. Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN).
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request. Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures.
Instructions for IC CS-03 certified equipment 1 The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
❑ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
❑ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ❑ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
Following information is only for EU-member states: The symbol indicates that this product may not be treated as household waste. Please ensure this product is properly disposed as inappropriate waste handling of this product may cause potential hazards to the environment and human health. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.
CD-RW/DVD-ROM drive safety instructions ❑ The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ❑ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ❑ To prevent direct exposure to the laser beam, do not try to open the enclosure.
TEAC DW-224E Location of the required label CERTIFICATION TISH PRODUCT COMPLIES WITH DHHS RULES21CFR CHAPTER 1, SUBCHAPTER J APPLICABLE DATE OF MANUFACTURE MANUFACTURED: TEAC CORPORATION 3-7-3 NAKA-CHO, MUSASHINO-SHI, TOKYO, JAPAN User’s Manual xvii
HD DVD-ROM and HD DVD-R drive safety instructions ❑ The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ❑ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ❑ To prevent direct exposure to the laser beam, do not try to open the enclosure.
Toshiba SD-L902A Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPAL WITH DHHS RULES 21 CFR CHAPTER1, SUBCHAPTER J.
DVD Super Multi (+-R DL) drive safety instructions ❑ The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ❑ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ❑ To prevent direct exposure to the laser beam, do not try to open the enclosure.
TEAC DV-W28E Location of the required label CERTIFICATION TISH PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE DATE OF MANUFACTURE MANUFACTURED: TEAC CORPORATION 3-7-3 NAKA-CHO, MUSASHINO-SHI, TOKYO, JAPAN HLDS GSA-T20N Location of the required label COMPLIES WITHFDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Panasonic Communications Co.
Pioneer DVR-K17T Location of the required label COMPLIES WITHFDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by PIONEER CORPORATION 4-1. Meguro 1-chome, Meguro-ku TOKYO 153-8654, JAPAN Toshiba Samsung TS-L632D Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Table of Contents Preface Manual contents........................................................... xxxiii Conventions ................................................................. xxxiv Abbreviations .............................................................. xxxiv Icons ........................................................................... xxxiv Keys............................................................................ xxxiv Key operation.................................................
Options ...........................................................................1-17 Chapter 2 The Grand Tour Front with the display closed .........................................2-1 Left side ............................................................................2-3 Right side..........................................................................2-6 Back side ..........................................................................2-7 Underside ...............................................
Sleep mode....................................................................3-7 Restarting the computer .................................................3-8 System Recovery Options ..............................................3-9 System Recovery Options .............................................3-9 Create Optical Recovery Discs .....................................3-10 For HDD Recovery model............................................3-10 Restoring the preinstalled software from the Recovery HDD .....
Using the Computer in place of an HD DVD Player ....4-26 Before Connecting .......................................................4-26 Connecting to the Computer........................................4-27 Switching between Computer and Television Display .4-27 Display Compatibility ....................................................4-28 Writing CDs on CD-RW/DVD-ROM drive ......................4-29 Important message (CD-RW/DVD-ROM drive) ...........4-29 Before writing or rewriting .........................
Moving the computer.....................................................4-58 Heat dispersal ................................................................4-59 Chapter 5 The Keyboard Typewriter keys ................................................................5-1 F1 ... F12 function keys ...................................................5-2 Soft keys: FN key combinations.....................................5-2 Emulating keys on enhanced keyboard.........................5-2 Hot keys....................
Replacing the battery pack ...........................................6-14 Removing the battery pack ..........................................6-14 Installing the battery pack ............................................6-16 Starting the computer by password.............................6-16 Power-up modes..........................................................6-17 Windows utilities ..........................................................6-17 Hot keys......................................................
Precautions..................................................................8-14 Connecting...................................................................8-15 Disconnecting ..............................................................8-16 Security lock ................................................................8-16 Chapter 9 Troubleshooting Problem solving process ................................................9-1 Preliminary checklist ......................................................
Wireless LAN ...............................................................9-24 Bluetooth......................................................................9-25 i.LINK (IEEE1394) .......................................................9-25 Recovery Discs...........................................................9-26 TOSHIBA support ..........................................................9-27 Before you call .............................................................9-27 Chapter 10 Disclaimers CPU ..
Preface Congratulations on your purchase of the TOSHIBA Satellite A210/Satellite Pro A210 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite A210/Satellite Pro A210 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, CTRL + C means you must hold down CTRL and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xxxvi User’s Manual
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
General Precautions Heat injury ❑ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer low-heat injury.
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not pre- installed by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction INTRODUCTION Software Windows Vista™ ◆ The following software is preinstalled: • Microsoft® Windows Vista™ • Modem Driver (Can be used only for Modem models) • Display Drivers for Windows • Wireless LAN driver (Can be used only for Wireless LAN models) • Sound Driver for Windows • TOSHIBA DVD Player (Is pre-installed with CD-RW/DVD-ROM drive model or DVD Super Multi drive model) • TOSHIBA HD DVD Player (Is pre-installed with HD DVD-ROM drive model or HD DVD-R drive model) • LAN Drivers • Blu
Introduction ◆ Documentation: • User Information Guide • Instruction Manual for Safety & Comfort • End User License Agreement Features This computer incorporates the following features and benefits: Processor Built-in Please visit your region’s website for the configuration details of the model that you have purchased. Memory Slots Video RAM User’s Manual PC2-4200 or PC2-5300 512 MB, 1024 MB or 2048 MB memory modules can be installed in the two memory slots.
Introduction Disks INTRODUCTION Hard disk drive The computer has an integrated, 2 1/2" hard disk drive (HDD) for nonvolatile storage of data and software. It comes in the following sizes. 60 GB 80 GB 100 GB 120 GB 160 GB 200 GB 250 GB 300 GB Disclaimer (Hard disk drive capacity) CD-RW/DVDROM drive 1-4 For more information on the Disclaimer regarding Hard disk drive capacity, please refer to the Disclaimer section in chapter 10.
Introduction DVD Super Multi (+-R DL) drive • DVD-R • DVD-RW • DVD+R • DVD+RW • DVD-RAM • DVD+R DL • DVD-R DL • CD-DA • CD-Text • Photo CD (single/multi-session) • CD-ROM Mode 1, Mode 2 • CD-ROMXA Mode 2 (Form1, Form2) • Enhanced CD (CD-EXTRA) • CD-G (Audio CD only) • Addressing Method 2 User’s Manual 1-5 INTRODUCTION Some models are equipped with a full-size DVD Super Multi (+- R DL) drive module that lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.
Introduction INTRODUCTION HD DVD ROM drive 1-6 Some models are equipped with a full-size HD DVDROM drive module that lets you run CD's or DVD's without using an adaptor. The drive reads DVD-ROM's at a maximum 8x speed and CD-ROM's at a maximum 24x speed, and HD DVD's at a maximum 1x speed and writes CD-R's at up to 16x speed, CD-RW's at up to 10x speed, DVD-R's and DVD+R's at up to 4x speed, DVDRW's and DVD+RW's at up to 4x speed, DVD-R (Dual layer) at up to 2x speed, DVD+R (Double Layer) at up to 2.
Introduction HD DVD-R drive Keyboard Built-in User’s Manual 85 keys or 86 keys, compatible with IBM® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. See Chapter 5, The Keyboard, for details. 1-7 INTRODUCTION Some models are equipped with a full-size HD DVD-R drive module that lets you run CD's or DVD's without using an adaptor.
Introduction INTRODUCTION Pointing Device Built-in A Touch Pad/Dual Mode Pad and control buttons in the palm rest enable control of the on-screen pointer. Battery pack The computer is powered by one rechargeable lithiumion battery pack. The internal RTC battery backs up the Real Time Clock (RTC) and calendar. The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord.
Introduction Slots Express Card This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use flash memory (SD/SDHC/MS/MS Pro/MMC/xD memory cards). (Provided with some models) Express Card slot allows you to install a Express Card™/34 or Express Card™/54 to expand functionality. Refer to Chapter 8, Optional Devices, for details.
Introduction INTRODUCTION Modem Bluetooth® Wireless Communication Switch Some computers in this series are equipped with an internal modem. The internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix C. The speed of date transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.
Introduction Special Features User’s Manual 1-11 INTRODUCTION The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Display automatic This feature automatically cuts off power to the internal power off display when there is no keyboard input for a time specified.
Introduction INTRODUCTION Battery save mode Panel power on/off Low battery automatic hibernation Heat dispersal Hibernation Sleep 1-12 This feature lets you save battery power. You can specify the Power Save Mode in the Profile item in TOSHIBA Power Saver. This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver.
Introduction TOSHIBA Value Added Package - Internet button - CD/DVD button TOSHIBA Zooming Utility TOHSIBA PC Diagnostic Tool TOSHIBA Flash Cards The starting application from the button can be changed. This utility allows you to enlarge or reduce the icon size on the Windows Desktop, or the zoom factor associated with specific supported applications.
Introduction INTRODUCTION TOSHIBA Accessibility The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the TOSHIBA Hot-key functions. In use, the utility allows you to make the FN key "sticky", that is you can press it once, release it, and then press one of the "F" keys in order to access its specific function. When set, the FN key will remain active until another key is pressed.
Introduction TOSHIBA DVD-RAM Utility TOSHIBA DVD-RAM Utility has the function of Physical Format and Write-Protect to DVD-RAM. Ulead DVD Movie®Factory for TOSHIBA TOSHIBA ConfigFree You can boot TOSHIBA DVD-RAM Utility from the menu bar as follows. Start → All Programs → TOSHIBA → CD&DVD Applications → DVD-RAM Utility You can edit digital video and make a DVD-Video and support Labelflash function. ConfigFree is a suite of utilities to allow easy control of communication device and network connections.
Introduction INTRODUCTION Fingerprint Utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard. Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ❑ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer).
Introduction Options User’s Manual 1-17 INTRODUCTION You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory expansion Two memory expansion slots are available for installing 512 MB, 1024 MB or 2048 MB memory modules. The modules are PC2-5300, 200-pin, SO Dual In-line (SODIMM).
INTRODUCTION Introduction 1-18 User’s Manual
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Figure 2-1 shows the computer’s front with its display panel in the closed position.
The Grand Tour Volume control Microphone jack THE GRAND TOUR Headphone jack Infrared receiver window Multiple Digital Media Card Slot System Indicators Wireless communication switch Use this dial to adjust the volume of the system speaker and headphones. A standard 3.5 mm mini microphone jack enables connection of a monaural microphone or other device for audio input. A standard 3.5 mm mini headphone jack enables connection of a stereo headphone (16 ohm minimum) or other device for audio output.
The Grand Tour Left side Figure 2-2 shows the computer’s left side. FAN VENT VIDEO-OUT JACK EXPRESS CARD SLOT MONITOR PORT USB PORTS I.LINK HDMI* (IEEE 1394) PORT* *Depending on the model you purchased Figure 2-2 The left side of the computer External monitor port Fan vent This 15-pin port lets you connect an external monitor. Provides air flow for the fan. Be careful not to block the fan vent. Also be careful to keep foreign objects out of the vents.
The Grand Tour Video-out jack LAN jack THE GRAND TOUR i.LINK (IEEE 1394) Port Plug a 4-pin S-Video connector into this jack. This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 Mbit/s, 10BASET) or Fast Ethernet LAN (100 Mbit/s, 100BASE-TX). The LAN has two indicators. See Chapter 4, Operating Basics, for details. Connect an external device, such as a digital video camera to this port for high-speed data transfer. Some models are equipped with a i.LINK port.
The Grand Tour Universal Serial Bus Ports The two Universal Serial Bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. (The ports also support USB 1.1) . Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry. User’s Manual THE GRAND TOUR Operation of all functions of all USB devices has not been confirmed. some functions might not execute properly.
The Grand Tour Right side Figure 2-3 shows the computer’s right side. MODEM JACK* THE GRAND TOUR SECURITY LOCK SLOT OPTICAL DISC DRIVE USB PORTS DC IN 19V *The availability of Modem Jack is depending on the model you purchased. Figure 2-3 The right side of the computer Universal Serial Bus Ports The two Universal Serial Bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. (The ports also support USB 1.
The Grand Tour Security lock slot DC IN 19V A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft. The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer. Back side Figure 2-4 shows the computer’s back side.
The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. BATTERY PACK BATTERY RELEASE LATCH THE GRAND TOUR BATTERY PACK LOCK MEMORY MODULE COVER Figure 2-5 The underside of the computer Battery pack Battery release latch Battery pack lock Memory module cover 2-8 The battery pack powers the computer when the AC adaptor is not connected.
The Grand Tour Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle.
The Grand Tour Stereo Speaker THE GRAND TOUR Fingerprint Sensor The speaker emits sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Just by swiping the finger against the fingerprint sensor, the following functions will be enabled (Provided with some models): ❑ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer). ❑ Files and folders can be encrypted/decrypted and third party access to them prevented.
The Grand Tour AV Button Six buttons are provided with some models. Play/Pause Button STOP Previous Button Next Button User’s Manual Press this button to begin playing an audio CD, a DVD movie or digital audio files. This button also acts as a Pause button. Press this button to stop play. Press this button to advance to the previous track, chapter or data. Press this button to advance to the next track, chapter or data.
The Grand Tour System indicators Figure 2-7 shows the system indicators, which light when various computer operations are in progress. MULTIPLE DIGITAL MEDIA CARD SLOT DISK THE GRAND TOUR MAIN BATTERY DC IN POWER Figure 2-7 System indicators Power source/system indicators DC IN Power Main Battery Disk Multiple Digital Media Card Slot 2-12 The DC IN indicator glows blue when DC power is supplied from the AC power adaptor.
The Grand Tour Keyboard indicators When the CAPS LOCK indicator glows the keyboard is in all-caps mode. CAPS LOCK INDICATOR This indicator glows green when the alphabet keys are locked in uppercase. CAPS LOCK The figures below show the positions of the keypad overlay indicators and the CAPS LOCK indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers.
The Grand Tour Optical disc drive CD-RW/DVD-ROM drive, DVD Super Multi (+-R DL) drive, HD DVD-ROM drive or a HD DVD-R drive. An ATAPI interface controller is used for CD/DVD/ HD DVD-ROM operation. When the computer is accessing a CD/DVD/HD DVD, an indicator on the drive glows. About the HD DVD THE GRAND TOUR This chapter describes the features, use of HD DVD and HD DVD Media.
The Grand Tour dard. This device does not support advanced features of the HD DVD Video standard as defined by the DVD Forum, including picture-in-picture and network dowload features. Screen movement may not be smooth, and performance may be lowered with some HD DVD content. Playback of high bit rate content may cause frame dropping, audio skipping or decrease in computer performance. ❑ Viewing of HD DVD content on an external display requires an HDCP capable HDMITM or DVI input on the external display.
The Grand Tour Writable discs This section describes the types of writable CD/DVD/HD DVD discs. Check the specifications for your drive to for the type of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics. THE GRAND TOUR CDs ◆ CD-R discs can be written only once. The recorded data cannot be erased or changed. ◆ CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4 to 10 speed discs.
The Grand Tour HD DVDs Like CD and DVD, HD DVD is divided into the read-only and recordableformats listedbelow. ❑ Some media cannot be used with this product. Be sure to thoroughly read section "HD DVD-ROM drive" or "HD DVD-R drive" of this before using this product. ❑ HD DVD-Video: For video playback. Used to store movies and other video. ❑ HD DVD-ROM: Read-only media. ❑ HD DVD-R: A recordable media which can be written to only once.
The Grand Tour Formats Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable.
The Grand Tour DVD Super Multi (+-R DL) drive The full-size DVD Super Multi drive module lets you record data to s as rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour HD DVD ROM drive The full-size HD DVD ROM drive module lets you record data to s as rewritable CDs as well as run either 12 cm (4.72") HD DVD,12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. THE GRAND TOUR The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour HD DVD-R drive The full-size HD DVD-R drive module lets you record data to s as rewritable CDs as well as run either 12 cm (4.72") HD DVD,12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour Remote Controller Your computer includes a Remote Controller which enables you to perform some functions of your computer from a distant location. The following figure shows the buttons on the Remote Controller. Your can use your Remote Controller with Media Center to play CDs, DVDs and videos, to view pictures and to watch and record television programs. The Remote Controller helps you to control the playback of a movie through Media Center .
The Grand Tour Refer to the Using the Remote Controller section in this chapter for information on how to use the Remote Controller as well as how to install and remove its batteries.
The Grand Tour Power THE GRAND TOUR Record Stop Pause Play Starts or terminates the operating system.This button functions like the Power button of your computer. By default, the Sleep Mode is equivalent to the Power Off state of your computer. To change the setting, click Start, select Control panel → System and Maintenance → Power Options → System Settings. The following four options are available: Do nothig, Sleep, Hibernate and Shut down.
The Grand Tour Volume + Volume Start Channel/Page up (+) and down (-) Mute Recorded TV Increases the volume while viewing DVD's or replaying CD's. Decreases the volume while viewing DVD's or replaying CD's. Opens Media Center to the main window. No function. Guide Opens Media Center to the main window. Live TV Opens Media Center to the main window. DVD Menu Numbers Clear Enter User’s Manual Opens the main menu on a DVD movie, if available.
The Grand Tour Using the Remote Controller This computer includes a remote control unit, which allows you to control some of your computer's functions from a distant location. ❑ The Remote Controller is designed specifically for this computer. ❑ Some application programs may not support remote control functions. THE GRAND TOUR Operational range of the Remote Controlle Point the Remote controller at your computer and press a button. The operational angle and distance are described below.
The Grand Tour *The appearance of the provided Remote Controller may vary from model to model, and it is not provided with some model. Even if within the effective scope as described above, the remote control may malfunction or not work correctly in the following cases. When an obstacle stands between the infrared receiver window of your computer and the Remote Controller ❑ When direct sunlight or strong fluorescent light strikes the infrared receiver window.
The Grand Tour THE GRAND TOUR Observe the following precautions when using the battery of the Remote Controller. ❑ Do not use batteries other than those specified. ❑ Ensure that you insert the batteries with their polarities correctly aligned (+ or -). ❑ Do not recharge, heat, disassemble or short the battery, or put it into a fire or flame. ❑ Do not use a battery whose 'recommended expiration date' has been reached, or which is completely discharged.
The Grand Tour BATTERY COVER Figure 2-12 Opening the battery cover BATTERIES Figure 2-13 Inserting the batteries 3. Close the battery cover. Close the cover securely until it clicks BATTERY COVER Figure 2-14 Closing the battery cover User’s Manual 2-29 THE GRAND TOUR 2. Insert the batteries in place. Be sure to place the batteries with their polarities (+ and -) in the correct position.
The Grand Tour Replacing the batteries When the batteries in the Remote Controller reach the end of their life, the Remote Controller may not operate correctly or work only within a short distance from your computer. In this instance, you should purchase new batteries and replace the discharged ones. 1. Open the battery cover on the back side of the Remote Controller. THE GRAND TOUR 2. Replace the batteries.Be sure to place the batteries with their polarities (+ and -) in the correct position.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6 Power and Power-Up Modes for details.
THE GRAND TOUR The Grand Tour 2-32 User’s Manual
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator on the front of the computer should glow. Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you. When you open the display, hold it with both hands and lift up slowly. .
Getting Started POWER BUTTON Figure 3-4 Turning on the power Starting up for the first time GETTING STARTED When you first turn on the power, the computer’s initial screen is the Microsoft® Windows Vista™ Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Sleep mode.
Getting Started 3. Click Windows Start button, point to , and then select Shut Down. 4. Turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The hibernation feature does not save the status of peripheral devices.
Getting Started Starting Hibernation To enter Hibernation mode, follow the steps below. Windows Vista™ 1. Click Windows Start button. 2. Point to . 3. Select Hibernate. Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel. 2. Open Mobile PC and open Power Options. 3. Select Choose what the power button does. GETTING STARTED 4.
Getting Started Sleep mode In sleep mode the power remains on, but the CPU and all other devices are in sleep mode. ❑ Before entering Sleep mode, be sure to save your data. ❑ Do not install or remove a memory module while the computer is in sleep mode. The computer or the module could be damaged. ❑ Do not remove the battery pack while the computer is in sleep mode (unless the computer is connected to an AC power source). Data in memory will be lost.
Getting Started When you turn the power back on, you can continue where you left when you shut down the computer. ❑ When the computer is shut down in sleep mode, the power indicator glows amber. ❑ If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Sleep mode consumes more power. Sleep limitations Sleep will not function under the following conditions: ❑ Power is turned back on immediately after shutting down.
Getting Started System Recovery Options About 1.5GB hidden partition is allocated on the hard disk drive for the System Recovery Options. This partition stores files which can be used to repair the system in the event of a problem. System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes some tools to repair startup problems, run diagnostics or restore the system.
Getting Started Create Optical Recovery Discs For HDD Recovery model A recovery image of your computer is stored on the hard disk. You may use this image to create CD or DVD recovery discs using the following steps: 1. Select either blank CDs or DVDs media. 2. The application will allow you to choose a type of media to create recovery CDs/DVD including: CD-R, CD-RW, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD+R DL and DVD-R DL. Some media may not be compatible with Optical Drive of your computer.
Getting Started In addition, if you use a third-party partitioning program to reconfigure partitions on your hard disk, it may become impossible to re-setup your computer. You can not use System Recovery Options if restoring the pre-installed software without System Recovery Options. 1. Turn off your computer. 2. While holding down 0 (zero) key on the keyboard, turn on your computer. 3. A menu appears. Follow the on-screen instructions.
Getting Started 3. Use the up or down cursor key to select CD/DVD in the display menu. For details, refer to the Boot Priority section in Chapter 7, HW Setup and Passwords. 4. A menu appears. Follow the on-screen instructions. When drivers Utilities are installed, you can setup the respective drivers and utilities from the following folder.
Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad/Dual Mode Pad, the fingerprint sensor, optical disc drives, the web camera, the microphone, the internal modem, wireless communication and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Using the Touch Pad/Dual Mode Pad To use the Touch Pad/Dual Mode Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics Dual Mode Pad Button function (Dual Mode Pad is provided with some models) MAIL BUTTON CONFIG FREE WINDOWS PHOTO GALLERY SWITCH BUTTON VOLUME APPLICATION BUTTONS Figure 4-2 Dual Mode Pad Button Switch button OPERATING BASICS Volume 4-2 To switch between Cursor Mode and Button Mode. When you switch to Button Mode, the pad blinks blue. Increases or decreases the volume of speaker and headphone. Mail button Starts your mail box for you to receive and send mails.
Operating Basics Windows Photo Gallery Application buttons Windows Photo Gallery gives you many tools for your digital photos and videos.You can organize, find, and view your photos and videos, as well as edit, print, and share them from within Windows Photo Gallery. It also makes it easy to transfer your photos from your camera to your computer, using a simple import process Three application buttons have default setting. You can assign other functions and programs to button 1 to 3.
Operating Basics Points to note about the Fingerprint Sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ❑ Do not scratch or poke the sensor with your nails or any hard or sharp objects. ❑ Do not press the sensor strongly. ❑ Do not touch the sensor with a wet finger or any wet objects. Keep sensor surface dry and free of water vapor.
Operating Basics recognition success rate. Also if the fingerprint is worn down or the finger becomes thinner or fatter, the recognition success rate may be lowered. ❑ The fingerprint for each finger is different and unique. Please ensure that only the registered or enrolled fingerprint or fingerprints are used for identification. ❑ Check sliding position and speed (see the drawing below). ❑ Fingerprint data is enrolled up to twenty one.
Operating Basics ❑ Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times.Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility. The following illustrations show the correct way to slide your finger over the recognition sensor. Align the finger and sensor as shown on the above figure.
Operating Basics 1. Click Start, Point to All Programs, point to Protector Suite QL and click User Enrollment. You can also start User Enrollment Wizard using the following method. ❑ Click the icon in the Task Bar. ❑ Swipe your finger across the Fingerprint Sensor. 2. The User's Password screen is displayed. Ensure the same Windows logon username is displayed before entering a password into the Enter your Password field. Click Next. 3. Click Next. 4.
Operating Basics Windows Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the PCs, as user selection can be skipped. Fingerprint Authentication Procedure 1. Start up the computer. 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor.
Operating Basics Fingerprint System Boot Authentication General The fingerprint authentication system can be used to replace the keyboardbased User Password authentication system when booting up. If you do not want to use the fingerprint authentication system for password authentication when booting up, but prefer to use the keyboard-based system instead, press the BACK SPACE key when the Fingerprint System Bootjuhu Authentication screen is displayed.
Operating Basics 4. Power-on Security screen is displayed. Place a checkmark in Replace the power-on and hard drive passwords with the fingerprint reader and click OK. The modified configuration for Fingerprint Power-on Security becomes effective the next time the system is booted up.
Operating Basics Fingerprint utility limitations TOSHIBA does not guarantee that the Fingerprint utility technology will be completely secure or error-free. TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Operating Basics Using optical disc drives The text and illustrations in this section refer primarily to the optical disc drive. However, operation is the same for all other optical disc drives. The full-size drive provides high-performance execution of CD/DVD/HD DVD ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVD/HD DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD/HD DVD-ROM operation.
Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the eject button to open the drawer slightly. EJECT BUTTON Figure 4-3 Pressing the eject button b. Pressing the eject button will not open the drawer when the drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Operating Basics 2. Grasp the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3. Lay the CD/DVD/HD DVD, label side up, in the drawer. OPERATING BASICS Figure 4-6 Inserting a CD/DVD/HD DVD When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD/HD DVD tray. Therefore, you will need to turn the CD/DVD/HD DVD at an angle when you place it in the tray.
Operating Basics 4. Press gently at the center of the CD/DVD/HD DVD until you feel it click into place. The CD/DVD/HD DVD should lie below the top of the spindle, flush with the spindle base. 5. Push the center of the drawer to close it. Press gently until it locks into place. If the CD/DVD/HD DVD is not seated properly when the drawer is closed, the CD/DVD/HD DVD might be damaged. Also, the drawer might not open fully when you press the eject button.
Operating Basics 2. The CD/DVD/HD DVD extends slightly over the sides of the drawer so you can grasp it. Hold the CD/DVD/HD DVD gently and lift it out. Figure 4-8 Removing a CD-RW/DVD/HD DVD-ROM 3. Push the center of the drawer to close it. Press gently until it locks into place. AV Button function This section describes a button function. Six button are provided with some models.
Operating Basics Using TOSHIBA HD DVD PLAYER to enjoy HD DVDs HD DVD Playback Restrictions HD DVD-ROM drive and HD DVD-R drive model allow users to enjoy the strong visuals of HD DVDVideo. "TOSHIBA HD DVD PLAYER" software is provided for playback of HD DVDVideo. Notes on use HD DVD Playback HD DVD is a new standard which makes use of new technologies. As such, there is a possibility of problems occurring related to connection, compatibility or operation with some discs and other digital devices.
Operating Basics Notes on playing HD DVD Video discs HD DVD Video discs ❑ Please use "TOSHIBA HD DVD PLAYER" for HD DVD Video playback. "Windows Media Player" and other commercially available software cannot be used for HD DVD Video playback. ❑ HD DVD Video playback may take several moments to begin. ❑ When playing an HD DVD (Twin format disc), run it from the "TOSHIBA HD DVD Launcher Menu". Only the HD DVD Layer of an HD DVD (Twin format disc) can be played in the "TOSHIBA HD DVD PLAYER".
Operating Basics ❑ Do not configure the Display automatic power off function to run while the "TOSHIBA HD DVD PLAYER" is running. ❑ The Windows Aero function is disabled while the "TOSHIBA HD DVD PLAYER" is running. Display Devices & Audio "TOSHIBA HD DVD PLAYER" will only run when "Colors" is set to "Highest (32 bit)". The "Colors" setting can be adjusted on the "Monitor" tab in the "Display Settings".
Operating Basics TOSHIBA HD DVD PLAYER ❑ "TOSHIBA HD DVD PLAYER" software is supported for playback of HD DVD Video, DVD-Video and DVD-VR. ❑ The "TOSHIBA HD DVD PLAYER" does not have a parental control function. ❑ In order to protect copyrights, the Windows Print Screen function is disabled when "TOSHIBA HD DVD PLAYER" is running. (Print Screen functions are disabled even when running other applications besides "TOSHIBA HD DVD PLAYER" and when "TOSHIBA HD DVD PLAYER" is minimized.
Operating Basics If this occurs, select Play HD DVD movie or Run the HD DVD Launcher, then click OK to launch the TOSHIBA HD DVD PLAYER. Figure 4-10 Application selection screen 2. Touch the CD/DVD panel on the Front operation panel. Or select Start → All Programs → TOSHIBA HD DVD PLAYER to start "TOSHIBA HD DVD PLAYER". The TOSHIBA DVD PLAYER can also be started from the Media Center top menu. Operating TOSHIBA HD DVD PLAYER Notes on Using "TOSHIBA HD DVD PLAYER".
Operating Basics ❑ If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, touch pad and mouse menu operations may not be able to be used. HELP MAXIMIZE SETTINGS MINIMIZE EXIT DISPLAY AREA OPERATING BASICS TOSHIBA HD DVD PLAYER CONTROL WINDOW Figure 4-11 TOSHIBA HD DVD PLAYER windows Display Area Maximize Settings 4-22 Displays video. Double click on the Display Area to toggle full screen display mode on and off.
Operating Basics Opens help. Minimizes the window of TOSHIBA HD DVD PLAYER. Closes TOSHIBA HD DVD PLAYER. The buttons on the panel are used to control playback of HD DVD-Video discs. Click the Display Area to display the Control window when it is hidden. Please refer to the following "TOSHIBA HD DVD PLAYER Control window" section for more information.
Operating Basics Always on top Exit Current position Volume control Mute Multi Audio Channel Output EJECT PREVIOUS CHAPTER NEXT CHAPTER Sets the control window as always on top, so that it is not hidden by other windows or full screen display. Closes TOSHIBA HD DVD PLAYER. Displays the current position within the title on the bar icon. Adjusts the volume to the level selected by dragging the slider bar. Mutes the sound when clicked.
Operating Basics ANGLE TWIN FORMAT DISC (HD DVD SLECTED) TWIN FORMAT DISC (DVD SLECTED) SOUND SUBTITLE REPEAT TITLE/CHAPTER SEARCH DRIVE SPECIFICATION TOP MENU MENU RETURN Figure 4-14 TOSHIBA HD DVD PLAYER Control window (3) Subtitle Sound Angle Repeat Title/Chapter Search Drive Specification Switches between audio tracks for titles which have more than 1 audio track. Switches between angles for multi-angle compatible titles.
Operating Basics Using the Computer in place of an HD DVD Player Videos played using "TOSHIBA HD DVD PLAYER" included with the computer can be displayed on a television equipped with an HDMI input port. HD DVD-Video can only be displayed on the computer's display panel or on a television connected to the HDMI out port. HD DVD-Video cannot be displayed on televisions connected to the S-Video out port or external displays connected to the RGB connector.
Operating Basics Connecting to the Computer Turn off the television and computer before connecting. 1. Insert the HDMI cable plug into the HDMI out port on the computer. HDMI OUT PORT HDMI CABLE Figure 4-15 Connecting the HDMI out port 2. Insert the remaining HDMI cable plug into the HDMI input port on the television. 3. Turn on the television first, and then the computer. Audio will be output from both the television and the computer.
Operating Basics Notes on Operation ❑ Change the display device setting before playing HD DVD-Video. Do not change the display device while playing HD DVD-Video. ❑ Do not change the display device at the following times. • When reading or writing data. • When carrying out communications operations. ❑ HD DVD-Video cannot be played when using Clone or Dualview (extended desktop) displays modes. Set either the computer's display panel or the television as the sole display device.
Operating Basics Writing CDs on CD-RW/DVD-ROM drive You can use the CD-RW/DVD-ROM drive to write data to either CD-R or CDRW discs. The following applications for writing are supplied: TOSHIBA Disc Creator. CD-R discs can be written to only once. CD-RW discs can be rewritten many times. Important message (CD-RW/DVD-ROM drive) Before you write or rewrite to CD-R/RW disc, read and follow all setup and operating instructions in this section.
Operating Basics ◆ Do not run software such as a screen saver which can put a heavy load on the CPU. ◆ Operate the computer at full power. Do not use power-saving features. ◆ Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. ◆ Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and damage data.
Operating Basics Disclaimer (CD-RW/DVD-ROM drive) TOSHIBA does not bear responsibility for the following: ◆ Damage to any CD-R/RW disc that may be caused by writing or rewriting with this product. ◆ Any change or loss of the recorded contents of CD-R/RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.
Operating Basics ◆ However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: CD-RW: (High-Speed, MultiSpeed) CD-RW: (Ultra-Speed) DVD-R DVD+R DVD-RW DVD+RW DVD-RAM OPERATING BASICS DVD+R DL DVD-R DL DVD-R for Labelflash™ DVD+R for Labelflash™ TAIYO YUDEN CO., LTD. MITSUBISHI KAGAKU MEDIA CO., LTD Ricoh Co., Ltd. Hitachi Maxell Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD Ricoh Co., Ltd.
Operating Basics The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVDRAM is affected by the quality of the disc and the way it is used. ◆ There are two types of DVD-R discs: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. ◆ We can support only format 1 of DVD-R DL. Therefore you can not do the additional writing. If your data is under DVD-R(SL) capacity, we suggest to use DVD-R(SL) media.
Operating Basics ◆ Do not write while virus check software is running. Wait for it to finish, and then disable virus detection programs including any software that checks files automatically in the background. ◆ Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and data damage. ◆ Write from the computer’s HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device.
Operating Basics Disclaimer (DVD Super Multi (+-R DL) drive) TOSHIBA does not bear responsibility for the following: ◆ Damage to any CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/DVDRAM disc that may be caused by writing or rewriting with this product.
Operating Basics For further information on TOSHIBA Disc Creator and Ulead® DVD MovieFactory®, please refer to each software’s online manual or online helps. Refer to HD DVD Guide for information on accessing the online manual or online help. ❑ Please refer to the Writable discs, Chapter 2 for details about the types of writable CD, DVD and HD DVD discs that can be supported by this computer.
Operating Basics ◆ Damage that may be caused by using third party equipment or software. Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.
OPERATING BASICS Operating Basics ❑ This drive cannot use discs that allow writing faster than 8x speed (DVD-R and DVD+R media), 4x speed (DVD-RW and DVD+RW media), 5x speed (DVD-RAM media), 2x speed (DVD-R (Dual Layer) media) and 2.4x speed (DVD+R (Double Layer media). ❑ Some types and formats of DVD-R (Dual Layer) and DVD+R (Double Layer) discs may be unreadable. ❑ 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.
Operating Basics stance, even if you write only a small amount of data, it might take additional time to fill in the dummy data. When multiple drives that can write data to discs are connected, be sure that you do not write to or delete data from the wrong drive. ◆ Be sure to connect the AC adaptor to the computer before you write or rewrite any information. ◆ Before you enter either Sleep Mode or Hibernation Mode, take care to ensure that any DVD-RAM writing has been completed.
Operating Basics ◆ Do not perform any of the following actions: • Change users in the Windows VistaTM operating system. • Operate the computer for any other function, including such tasks as using a mouse or Touch Pad, or closing/opening the display panel. • Start a communication application such as a modem. • Apply impact or vibration to the computer.
Operating Basics DVD-RAM discs cannot be backed up using the 'Disc Backup' functionof TOSHIBA Disc Creator. ◆ You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R, DVD-R (Dual Layer), DVD-RW or HD DVD-R media using the 'Disc Backup' function of TOSHIBA Disc Creator. ◆ You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R, DVD+R (Double Layer) or DVD+RW media using the 'Disc Backup'function of TOSHIBA Disc Creator.
Operating Basics Data Verification To verify that data has been written or rewritten correctly to a data CD/DVD/HD DVD you should follow the steps below before you begin the write/rewrite process: 1. Display the setting dialog box by one of the following two steps: ❑ Click the Recording settings button( in the Data Disc mode. ) for writing on the main toolbar ❑ Select Setting for Each Mode → Data Disc in the Setting menu. 2. Mark the Verify written data check box. 3.
Operating Basics 5. Choose DVD Drive for Printer. e.g. PIONEER DVD.... 6. Add and customize the look of your images and text. 7. Click Labelflash setting and choose Draw Quality. 8. Click Print. How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DVCamcorder: 1. Click Start → All Programs → DVD MovieFactory for TOSHIBA → Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Insert a DVD-RW or DVD+RW disc in Burner. 3.
Operating Basics Important information for use Note the following limitations when you write video DVD: 1. Editing digital video. ❑ Log in with Administrator rights to use DVD MovieFactory. ❑ Make sure that your computer is running on AC power when using DVD MovieFactory. ❑ Operate the computer at Full Power. Do not use power-saving features. ❑ While you are editing DVD, you can display previews. However, if another application is running, the preview might not display properly.
Operating Basics • Install, remove or connect external devices, including the following: Express Card, SD card, USB device, external display, i.LINK devices, optical digital devices. ❑ Please verify your disc after recording important data. ❑ DVD-R/+R/-RW disc cannot be written in VR format. ❑ Not support to output VCD and SVCD format. 3. About Straight to Disc ❑ Not support to record on DVD-R/+R disc. ❑ Not support to record DVD+VR format by HDV. ❑ HDV support to burn DVD-Video only.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVD/HD DVD. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVD/HD DVD 1. Store your CD/DVD/HD DVD in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD/HD DVD. 3. Do not write on, apply a sticker to, or otherwise mark the surface of the CD/ DVD/HD DVD that contains data. 4.
Operating Basics Using the Web Camera(Built-in Web Camera is provided with some models.) This section describes the bundled webcam utility, which can capture still and video images. The web camera will auto-run when Windows starts. OPERATING BASICS 1. ACTIVE LED 2.
Operating Basics Using the software The web camera software is pre-configured to start when you turn on Windows Vista; if you need to restart it go to Start → Programs → Camera Assistant Software → Camera Assistant Software 1. Capture still images 2. Video Recording 3. Video Recording 4. Function 5. Display Window 6. Camera Resolution 7. Mute 8.
Operating Basics Properties Settings Help Choose from the Options tab to flip, zoom, flicker rate, night mode and backlight compensation; in the Image tab change the colour settings; in the profile tab change the lighting conditions.
Operating Basics Modem The availability of this feature is depending on the model you purchased. This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. ❑ In case of a lightning storm, unplug the modem cable from the telephone jack. ❑ Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Operating Basics 4. Select a region from the region menu or a telephony location from the submenu. • When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically. • When you select a telephony location, the corresponding region is automatically selected and it becomes the modem’s current region setting. Properties menu Click the icon with the secondary mouse button to display the following menu.
Operating Basics Dialing Properties Select this item to display the dialing properties. If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the internal modem cable, follow the steps below. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 wireless LAN standard (Revision A, B, G or Draft N). Supported features.
Operating Basics Security ◆ Be sure to enable encryption function. Otherwise your computer will allow the illegal access by outsider through wireless LAN to cause illegal instruction, eavesdropping, and loss or destruction of stored data. TOSHIBA strongly recommends the customer to enable the encryption function. ◆ TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof.
Operating Basics Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch toward the left of the computer to turn it on and toward the right of the computer to turn it off. Set the switch to off in airplanes and hospitals. Check the indicator. It will stop glowing when the wireless communication function is off.
Operating Basics LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) or Fast Ethernet LAN (100 megabits per second, 100BASETX)(depending on model you purchased). This section describes how to connect/ disconnect to a LAN. Do not install or remove an optional memory module while Wakeup on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.
Operating Basics 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. LAN JACK Figure 4-21 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN active indicator glows amber. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green.
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ◆ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ◆ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the display.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan.
OPERATING BASICS Operating Basics 4-60 User’s Manual
The Keyboard The computer’s keyboard layouts are compatible with a 104/105-key enhanced keyboard. By pressing some keys in combination, all the 104/105-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard THE KEYBOARD F1 ... F12 function keys The function keys, not to be confused with FN, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the FN key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: FN key combinations, in this chapter.
The Keyboard tion in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press FN + ENTER to simulate ENTER on the enhanced keyboard’s numeric keypad. Press FN + CTRL to simulate the enhanced keyboard’s right CTRL key. Press FN + ALT to simulate the enhanced keyboard’s right ALT key. Hot keys Hot keys (FN + a function or Esc key) let you enable or disable certain features of the computers.
THE KEYBOARD The Keyboard Instant security: Pressing FN + F1 to enter “Lock computer” mode. To restore your desktop, you need to log on again. Power Plan: Pressing FN + F2 changes the power settings. Sleep: Pressing FN + F3 switches the system to Sleep mode. Hibernation: Pressing FN + F4 switches the system to Hibernate mode. Output: Pressing FN + F5 changes the active display device.
The Keyboard Brightness Up: Pressing FN + F7 increases the computer’s display panel brightness in indiviual steps. Wireless: Pressing FN + F8 switches the active wireless devices if the wireless communication switch is switched on. If your wireless communication device is installed, no dialog box will not appear. Touch Pad: Pressing FN + F9 enables or disables the Touch Pad function.
THE KEYBOARD The Keyboard Zoom: Pressing FN + space changes the display resolution. TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows. TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows.
The Keyboard Windows special keys This key activates the Windows Start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the center of the keyboard with white letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard in figure 5-1.
The Keyboard THE KEYBOARD Numeric mode To turn on the Numeric mode, press FN + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-1. Press FN + F11 again to turn off the overlay. Figure 5-1 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold FN and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily using overlay (overlay off) 1. Press and hold down FN. 2. Check the keyboard indicators. Pressing FN turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release FN to return to normal keyboard operation.
THE KEYBOARD The Keyboard 5-10 User’s Manual
Chapter 6 Power and Power-Up Modes Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery. User’s Manual 6-1 POWER AND POWERUP MODES The computer’s power resources include the AC adaptor and internal batteries.
Power and Power-Up Modes Table 1: Power conditions Power on Power off (no operation) AC Battery fully • Operates • No charge adaptor charged • No charge • LED: Battery Blue • LED: Battery Blue connected DC IN Blue POWER AND POWERUP MODES DC IN Blue Battery • Operates • Quick charge partially • Charge • LED: Battery Amber charged or • LED: Battery Amber no charge DC IN Blue DC IN Blue No battery • Operates • No charge installed • No charge • LED: Battery off • LE
Power and Power-Up Modes Power indicators The Battery, DC IN and Power indicators on the system indicator panel alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery. The following indicator lights indicate the battery status: Flashing amber The battery charge is low. The AC adaptor must be connected to recharge the battery. Indicates the AC adaptor is connected and charging the battery.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status. Blue Indicates power is being supplied to the computer and the computer is turned on. Blinking amber Indicates the power was turned off while the computer was in Resume mode. POWER AND POWERUP MODES No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes The battery recharges the RTC batteries. The battery maintains the state of the computer when you enable Resume. When the computer is powered off in Resume mode, and the AC adaptor is not connected, the battery pack supply power to maintain data and programs in memory. If the battery pack is completely discharged, Resume does not function and the computer loses all data in memory.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions POWER AND POWERUP MODES Mishandling of batteries can cause death, serious injury or property damage.
Power and Power-Up Modes packs have different voltages and terminal polarities. Use of an improper battery could cause smoke, fire or rupture of the battery pack. 7. Never subject a battery pack to heat, such as storage near a heat source. Exposure to heat can cause the battery pack to ignite, explode or leak caustic liquid and cause death or serious injury. It could also fail or malfunction causing data lose. 8. Never expose the battery pack to abnormal shock, vibration or pressure.
Power and Power-Up Modes Caution 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack’s power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. POWER AND POWERUP MODES 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes amber indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don’t lose data) and automatically turns off.
Power and Power-Up Modes Battery charging notice The battery may not charge right away under the following conditions: ❑ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. Also, to ensure the battery charges to its full capacity, charge the battery at room temperature of 10° to 30°C (50° to 86°F). ❑ The battery is nearly completely discharged. Leave the AC adaptor connected for a few minutes and the battery should begin charging.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored in TOSHIBA Power Saver. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
Power and Power-Up Modes Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ❑ How you configure the computer (for example, whether you enable batterypower saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (3 cell) Battery pack (6 cell) Battery pack (9 cell) days (Sleep mode) about 15 days (Shutdown mode) about 3.5 days (Sleep mode) about 30 days (Shutdown mode) about 5.
Power and Power-Up Modes ❑ If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. ❑ Store spare battery packs in a cool dry place out of direct sunlight. Replacing the battery pack POWER AND POWERUP MODES When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator flashes amber shortly after fully recharging the battery, the battery pack needs to be replaced.
Power and Power-Up Modes BATTERY PACK LOCK BATTERY PACK Figure 6-1 Slide the locking latch to the unlocked position 6. Slide the battery release latch to free the battery pack for removal, then lift up the battery pack. BATTERY PACK BATTERY PACK LOCK BATTERY RELEASE LATCH Figure 6-2 Removing the battery pack 7. Pull the battery pack forward to remove it. For environmental reasons, do not throw away a spent battery pack. Please return spent battery pack to your TOSHIBA dealer.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. POWER AND POWERUP MODES 2. Insert the battery pack.
Power and Power-Up Modes To start up the computer with the user password, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message appears: Password = At this point, the hot keys FN + F1 to F9 do not work. They will function after you enter the password. 2. Enter the password. If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry.
Power and Power-Up Modes Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Sleep or Hibernation mode but not in boot mode. If the panel power off function is enabled and use Shut down Windows, do not close the display until the shut down function is completed. POWER AND POWERUP MODES System Auto Off This feature turns the system off automatically if it is not used for a set duration.
Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for Display, CPU, Boot priority, Keyboard, USB, LAN, General and password. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
HW Setup and Passwords General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Change or remove the password. (Default) Registered Set the password. A dialogue box will appear to let you set the password.
HW Setup and Passwords To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter Password: **** If you click the OK button before entering the password, Registered will appear on the display. 3. Click the OK button.
HW Setup and Passwords CPU Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary. (Default) Always Low CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at low power consumption and low speed.
HW Setup and Passwords If there are only 2 HDDs, the Boot Priority Options setting will be like the following. This procedure does not affect the settings. * In this computer, CD-ROM refers to the DVD-ROM, CD-R/RW or CD-RW/ DVD-ROM drives. To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. Use the up/down cursor keys to select boot device you want and press Enter.
HW Setup and Passwords Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in sleep mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in sleep mode. Enabled Enables Wake-up on Keyboard. Disabled Disables Wake-up on Keyboard. (Default) USB Legacy USB Support Use this option to enable or disable USB Legacy Emulation.
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices Express Card Installing an Express Card The Express Card slot is located on the left side of the computer. You can install one Express Card in the slot. Windows’ hot-install feature lets you install Express Card while the computer’s power is on. Do not install an Express Card while the computer is in sleep or hibernation mode. Some cards might not work properly. To install an Express Card, follow the steps below. 1. Insert the Express Card. 2. Press gently to ensure a firm connection.
Optional Devices Removing an Express Card To remove the Express Card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the Express Card. 2. Press the Express Card slightly to make it stretch out. 3. Grasp the Express Card and pull it out from the slot.
Optional Devices Multiple Digital Media Card Slot Some models are equipped with a Multiple Digital Media Card Slot that can accommodate Secure Digital (SD)/ Secure Digital High Capacity (SDHC)/ Memory Stick (MS)/Memory Stick Pro (MS Pro)/Multi Media Card (MMC)/xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD/SDHC/MS/MS Pro/ MMC/xD memory cards.
Optional Devices 2. Press gently to ensure a firm connection. SD/SDHC/ MS/MS PRO/ MMC/XD CARD MULTIPLE DIGITAL MEDIA CARD SLOT Figure 8-3 Inserting the memory card Keep foreign objects out of the Multiple Digital Media Card Slot. A pin or similar object can damage the computer's circuitry ❑ Make sure the SD/SDHC/MS/MS Pro/MMC/xD card is oriented properly before you insert it. ❑ Memory Stick Duo/PRO Duo and the Memory Stick adaptor are not compatible with the Multiple Digital Media Card Slot.
Optional Devices Removing a SD/SDHC/MS/MS Pro/MMC/xD card To remove the memory card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the inserted memory card. 2. Gently press the memory card inside the socket to eject it. 3. Grasp the card and remove it.
Optional Devices Memory expansion You can install additional memory in the computer’s memory module to increase the amount of RAM. Only memory modules with the following parts numbers can be installed: 512MB: PA3511U-1M51 1GB: PA3512U-1M1G 2GB: PA3513U-1M2G Installing memory module To install a memory module, make sure the computer is in boot mode then: 1. Turn the computer off in boot mode. Refer to the Turning off the power section in Chapter 3.
Optional Devices Figure 8-5 Removing the cover 6. Insert the memory module into the connector on the computer. Press the module carefully and firmly to ensure a solid connection. 7. Push the module down so that it lies flat and is secured by two latches. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. OPTIONAL DEVICES . Figure 8-6 Inserting the memory module 8. Seat the cover and secure it with one screw. 9.
Optional Devices memory is recognized. If it is not recognized, check the module’s connection. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer. ❑ If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them.
Optional Devices Figure 8-7 Removing the memory module 7. Seat the cover and secure it with one screw. Additional battery pack (6 Cell and 9 Cell) You can increase the portability of the computer with additional battery packs (6 Cell: PA3534U-1BRS/PA3534U-1BAS, 9 Cell: PA3535U-1BRS/PA3535U1BAS). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes.
Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer, Port Replicator. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. If an external monitor is connected to the computer, do not connect the Port Replicator. First disconnect the external monitor from the computer then connect the Port Replicator and use its external monitor port. The Resume feature can be used with an external monitor.
Optional Devices Television A television can be connected to the video out port on the computer. To connect a television, follow the steps below. 1. Turn the computer off. 2. Use a video cable (not supplied) to connect the television to the video out port. VIDEO OUT PORT Figure 8-8 Connecting a television 3. Turn the television on. OPTIONAL DEVICES 4. Turn the computer on.
Optional Devices HDMI A HDMI monitor can be connected to the HDMI out port on the computer. 1080i, 720p, 576p and 480p signal formats can be supported. But actual signal format you can use depends on HDMI monitor. To connect monitor, follow the steps as detailed below: As the port operation of all HDMI (High-Definition Multimedia Interface) monitors has not been confirmed, some HDMI monitors may not function properly. 1. Plug one end of the HDMI cable into the HDMI port of the HDMI device.
Optional Devices Settings for audio on HDMI To set the audio device to use the HDMI, follow the steps below. 1. Click Start. 2. Click Control Panel. 3. Click Hardware and Sound. 4. Click Realtek HD Audio Manager. 5. Click Digital Output Device (HDMI). 6. Click the Set Default Device button. To set the audio device to use internal speaker, follow the steps below. 1. Click Start. 2. Click Control Panel. 3. Click Hardware and Sound. 4. Click Realtek HD Audio Manager. 5. Click Speakers. 6.
Optional Devices 3. If you are transferring data through an IEEE1394 hub, do not connect or disconnect other devices from the hub during data transfer. There is a likelihood that data will be damaged. Connect all devices to the hub before you turn on the computer’s power. 4. You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment. 5. If you connect/disconnect an i.LINK device to/from another i.
Optional Devices Disconnecting 1. Open the Safety Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. Refer also to the documentation that came with your i.LINK device. Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer.
Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting TROUBLESHOOTING ❑ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem Sometimes the system gives clues that can help you identify why it is malfunctioning.
Troubleshooting Hardware and system checklist ❑ System start-up ❑ ❑ ❑ Self test Power Password ❑ Keyboard ❑ ❑ ❑ ❑ ❑ ❑ LCD panel Hard disk drive CD-RW/DVD-ROM drive DVD Super Multi drive HD DVD-ROM drive HD DVD-R drive ❑ ❑ ❑ ❑ ❑ Diskette drive Infrared port Pointing device Touch/Dual Mode Pad device Fingerprint Sensor ❑ ❑ Express Card SD/SDHC/MS/MS Pro/MMC/ xD card ❑ ❑ Monitor Sound system ❑ TV output signal ❑ ❑ ❑ ❑ ❑ ❑ USB Modem Sleep/Hibernation LAN Wireless LAN Bluetooth ❑ i.
Troubleshooting TROUBLESHOOTING Self test When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the Hardware Setup, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A.
Troubleshooting AC power Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow blue) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the computer, contact your dealer.
Troubleshooting TROUBLESHOOTING Battery If you suspect a problem with the battery, check the DC IN indicator as well as the battery indicator. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t power the computer The battery may be discharged. Connect the AC adaptor to charge the battery. Battery doesn’t charge when the AC adaptor is attached (Battery indicator does not glow amber.
Troubleshooting Procedure Battery doesn’t power the computer as long as expected If you frequently recharge a partially charged battery, the battery might not charge to its full potential. Fully discharge the battery, then try to charge it again. Check the power consumption settings in Power Saver utility. Consider using a power saving mode. Password Problem Procedure Cannot enter password Refer to the Password section in Chapter 7, HW Setup and Passwords.
Troubleshooting TROUBLESHOOTING LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup and Passwords, for more information. Problem Procedure No display Press hot keys FN + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the LCD They might have come from contact with the keyboard, TouchPad or cPad. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner.
Troubleshooting CD-RW/DVD-ROM drive Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the DVD is dirty.
Troubleshooting TROUBLESHOOTING HD DVD ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting HD DVD-R drive Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the DVD is dirty.
TROUBLESHOOTING Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording. Do not run or start other software during writing. Do not jar the computer during writing. Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Problem Procedure Check the region code on the DVD. It must match that on the CD-RW/DVD-ROM drive. Region codes are listed in the Optical disc section in Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording.
Troubleshooting TROUBLESHOOTING Diskette drive Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. Some programs run correctly but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software needs. You cannot access the external 3 1/2" diskette drive Try another diskette.
Troubleshooting Touch Pad/Dual Mode Pad Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press ENTER. 2. Click the Buttons tab. 3. Set the double-click speed as instructed and click OK.
TROUBLESHOOTING Troubleshooting Problem Procedure When the reaction of Touch pad/Dual Mode Pad is sensitive to slow Adjust the touch Sensitivity. 1. Open the Control Panel. 2. Click the Printers icon and then the Other Hardware icon. 3. Click the Mouse icon. 4. Click the Device Setting tab. 5. Click the Setting button. 6. The Properties for Synaptics Touchpad on PS/2 port screen appears. Double-click Sensitivity in the Select an item section on the left side of the screen. 7.
Troubleshooting USB mouse Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click sped setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press ENTER. 2. Click the Buttons tab. 3.
Troubleshooting TROUBLESHOOTING Fingerprint Sensor Problem Procedure Reading of the fingerprint was not successful. Please try again using the correct posture. Refer to Using the Fingerprint Sensor in Chapter 4, Operating Basics. Try the recognition process again using another enrolled finger. The fingerprint cannot be read due to injuries to the finger. Try the recognition process again using another enrolled finger.
Troubleshooting Express Card Problem Procedure Express Card error occurs Reseat the Express Card to make sure it is firmly connected. TROUBLESHOOTING Refer also to Chapter 8, Optional Devices. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. SD/SDHC/MS/MS Pro/MMC/xD card Refer also to Chapter 8, Optional Devices.
Troubleshooting TROUBLESHOOTING Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hot keys FN + F5 to change the display priority and make sure it is not set for the internal display.
Troubleshooting Sound system Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer. If problems persist, contact your dealer.
Troubleshooting TROUBLESHOOTING USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
Troubleshooting Procedure After making a call you can’t hear a ring Make sure the tone or pulse selection in your communications application is set correctly. You can also use the ATD command. Refer to the chapter on AT commands in online help files for Appendix C, AT Command. Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval. Try lengthening this time interval.
Troubleshooting TROUBLESHOOTING Sleep/Hibernation Problem Procedure The system will not enter Sleep/Hibernation Is Windows Media Player open? The system might not enter Sleep/Hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Sleep/Hibernation. If problems persist, contact your dealer. LAN Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB.
Troubleshooting Bluetooth Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth Adpater is installed in the computer. The built-in Bluetooth function and an optional Bluetooth Adpater cannot operate simultaneously. If problems persist, contact your dealer. i.LINK (IEEE1394) Problem Procedure i.
Troubleshooting TROUBLESHOOTING Recovery Discs Problem Procedure The following message appears when executing Recovery Disc Creator. "The Recovery Disc Creator can not be launched because there is no recovery partition." You will see this message if you have previously chosen to remove the partition and are trying to create "Recovery Media". When there is no recovery partition, the Recovery Disc Creator cannot make Recovery Media.
Troubleshooting TOSHIBA support Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ❑ Review troubleshooting sections in the documentation for software and peripheral devices. ❑ If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions.
TROUBLESHOOTING Troubleshooting Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R 8H2 China TOSHIBA Personal Computer & Network (Shanghai) Co., Ltd. 43F, Hongkong new world tower, No. 300 Huai Hai Zhong Road, Shanghai, P.R. China 200021 United States of America TOSHIBA America Information Systems, Inc.
Chapter 10 Disclaimers This chapter slates the Disclaimer(s) information applicable to TOSHIBA computers. Central Processing Unit ("CPU") Performance Disclaimer.
Disclaimers product documentation. Contact Toshiba technical service and support, refer to TOSHIBA support section in chapter 9 Troubleshooting for more information. 64-Bit Computing. 64-bit processors are designed to take advantage of 32 and 64 bit computing.
Disclaimers shipped with your computer, or visit the Toshiba web site at www.pcsupport.toshiba.com. HDD Drive Capacity 9 1 Gigabyte (GB) means 10 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for 30 LCD Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology.
Disclaimers Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. [54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed.
Appendixes Appendix A Specifications..................................................................................... A-1 Appendix B Display Controller and Modes ..........................................................B-1 Appendix C V.90/V.92 .............................................................................................. C-1 Appendix D Wireless LAN ...................................................................................... D-1 Appendix E AC Power Cord and Connectors .........
APPENDIXES Appendixes-2 User’s Manual
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 362 (w) x 267.8 (d) x 33.5 (front) / 39.3 (rear) millimeters Weight (typical*) < 2.72 kilograms, configured with: 15.4" panel, DVD Combo drive, 3-cell battery, and modem. * Weight will vary depending on whether or not and what kind of options are adopted.
Specifications Built-in Modem The ability of this feature is depending on the model you purchased. Network control unit (NCU) Type of NCU Type of line Type of dialing AA Telephone line (analog only) Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Communication protocol APPENDIX A Communication speed Error correcting Data compression A-2 Data: Full duplex Fax: Half duplex Data ITU-T-Rec V.21/V.22/V.
Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.
APPENDIX B Video Modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on, resolution, number of colors and refresh rates.
Appendix C V.90/V.92 V.90 rates can be achieved only when one V.90 capable modem is connected to another. The TOSHIBA Internal modem will select automatically V.34 if the remote modem lacks V.90 capability or if a combination of network and/or phone line conditions prevent V.90 connection. V.90/V.92 mode Function Transmission speed Data V.90/V.92 From 56K (maximum) to 28Kbps (minimum) Reception only User’s Manual C-1 APPENDIX C The TOSHIBA internal modem uses V.90 technology.
APPENDIX C Table Result codes for a V.90 connection No.
AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
APPENDIX C C-4 User’s Manual
Appendix D Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications ■ Mini Card Compatibility ■ ■ IEEE 802.11 Standard for Wireless LANs Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
R-F Frequency ■ Band 5 GHz (5150-5850 MHz) (Revision A, Draft N) ■ Band 2.4 GHz (2400-2483.5 MHz) (Revision B, G, Draft N) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. ◆ The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
When installing Wireless LAN cards, the channel configuration is managed as follows: ◆ For wireless clients that operate in a Wireless LAN infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.
Frequency Range Channel ID 5150-5850 MHz Note *3 128 5640 132 5660*3 136 5680*3 140 5700*3 149 5745*3 US only*4 153 5765*3 US only*4 157 5785*3 US only*4 161 5805*3 US only*4 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. *3 These channels are available to A/B/G combo type only. *4 Available Area: US (USA, CANADA) only.
Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/ region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe and China.
The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
SCSI GLOSSARY (Abbreviations continued) SCSI: small computer system interface SIO: serial input/output SO-DIMM: small-outline dual in-line memory module SVGA: super video graphics adapter SDRAM: synchronized dynamic random access memory TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array VRM: video ready modem VRT: voltage reduction technology A adapter: A device that provides an inter
Byte Bluetooth: A short-range radio technology designed to simplify wireless communication among computers, communication devices and the Internet. B board: A circuit board. An internal card containing electronic components, called chips, which perform a specific function or increase the capabilities of the system. backup: A duplicate copy of files kept as a spare in case the original is destroyed.
cache memory GLOSSARY C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory. card: Synonym for board. See board.
Definition compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
delete GLOSSARY delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
hertz format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. folder: An icon in Windows used to store documents or other folders.
GLOSSARY hexadecimal hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer. hot dock/undock: Connecting or disconnecting a device to or from the computer while the computer’s power is turned on.
modem KB: See kilobyte. kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte and megabit. M main board: See motherboard. MDA: Monochrome Display Adapter. A video display protocol defined by the IBM Monochrome Display Adapter and its associated circuitry for direct drive TTL displays that supports a monochrome 720x350 text mode. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. level 2 cache: See cache.
GLOSSARY monitor monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
RAM password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject. pel: The smallest area of the display that can be addressed by software. Equal in size to a pixel or group of pixels. See pixel. peripheral component interconnect: An industry standard 32-bit bus. peripheral device: An I/O device that is external to the central processor and/ or main memory such as a printer or a mouse.
GLOSSARY restart restart: Resetting a computer without turning it off (also called ‘warm boot’ or ‘soft reset’). To restart the computer, press CTRL + ALT + DEL while the computer is on. See also boot. RCA jack: A single-pin connector that carries composite video signals, which include both contrast and color information. See also S-video. RGB: Red, green, and blue.
write protection synchronous: Having a constant time interval between successive bits, characters or events. system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk. T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output.
GLOSSARY Glossary-14 User’s Manual
Index using A B Battery pack 6-6 additional 8-10 location 2-8 replacing 6-14 Battery, See also Battery pack charging 6-9 extending life 6-13 indicator 2-12, 6-3 monitoring capacity 6-11 real time clock 6-5 safety precautions 6-6 types 6-4 C CD-RW/DVD drive 1-4, 4-29 Cleaning the computer 4-58 COM level, see Ports, serial D DC IN indicator 2-12, 6-3 Disk indicator 2-12 Display 2-9 automatic power off 1-11 opening 3-3 output, See Hot keys documentation list 1-1 DVD-ROM drive User’s Manual Equipment chec
Index FN Sticky key Function keys 5-6 5-2 2 F1 ...
Index Monitor external problems 9-20 Moving the computer 4-58 N Numeric keypad, See Keypad overlay O Operating System 1-10 Overlay, See Keypad overlay P 3 hibernation 9-24 keyboard 9-7 LAN 9-24 User’s Manual R Real time clock battery, See Battery Recovery Media 3-11 S ScrLock (FN + F12), See Soft keys SD/SDHC/MS/MS Pro/MMC/xD card 9-19 problems 9-19 Security lock 1-10 attaching 8-16 location 2-6 Self Test, See Problems Serial port, See Ports, serial adaptor 1-17, 2-31, 8-10 options 1-17 Sleep 1-12 S
Index problems 9-21 speaker 2-10 volume control 2-2 T TOSHIBA Power Saver TV 8-12 1-13 U INDEX Utilities list 1-13 USB 1-8 location 2-3, 2-6 problems 9-22 V Video modes, Appendix B Video RAM 1-3 Video-out jack 1-8, 2-4 Volume control, See Sound system W Wireless LAN 1-9 using 4-53 Index-4 User’s Manual