Toshiba Personal Computer Satellite T130/Satellite ProT130/PORTEGE T130 Maintenance Manual TOSHIBA CORPORATION File Number 960-Q08 Satellite T130,Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)
Copyright © 2009 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Personal Computer Satellite T130, Satellite Pro T130, PORTEGE T130 Maintenance Manual First edition August. 2009 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite T130, Satellite Pro T130, and PORTEGE T130 Series. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention.
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite T130, Satellite Pro T130, PORTEGE T130 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type.
Table of Contents Chapter 1 Hardware Overview 1.1 Features ..........................................................................................................................1 1.2 System Block Diagram ..................................................................................................6 1.3 2.5-inch Hard Disk Drive...............................................................................................9 1.4 Keyboard..........................................................
Chapter 2 Troubleshooting Procedures 2.1 Troubleshooting ............................................................................................................ 1 2.2 Troubleshooting Flowchart........................................................................................... 2 2.3 Power Supply Troubleshooting..................................................................................... 6 2.4 2.5 2.6 2.7 2.8 2.9 Procedure 1 Power Status Check ...............................
2.10 2.11 2.12 Procedure 1 Diagnostic Test Program Execution Check .............................26 Procedure 2 Connector Check and Replacement Check..............................26 Wireless LAN Troubleshooting...................................................................................27 Procedure 1 Transmitting-Receiving Check ................................................27 Procedure 2 Antennas' Connection Check ...................................................
Chapter 3 Diagnostic Programs 3.1 Tests and Diagnostics Software Overview ................................................................... 2 3.2 Executing the Diagnostic Test ...................................................................................... 3 3.3 Subtest names................................................................................................................ 7 3.4 System Test...........................................................................................
3.21.
Chapter 4 4.1 Replacement Procedures Overview....................................................................................................................... 1 Safety Precautions ................................................................................................... 2 Before You Begin ................................................................................................... 3 Disassembly Procedure..................................................................................
Appendices Appendix A Handling the LCD Module ................................................................................1 Appendix B Board Layout .....................................................................................................1 Appendix C Pin Assignments.................................................................................................1 Appendix D Keyboard Scan/Character Codes .......................................................................
Chapter 1 Hardware Overview Satellite T130 and Satellite ProT130, PORTEGE T130Maintenance Manual (960-Q08)
Chapter1 Hardware Overview 1 Hardware Overview Chapter 1 Contents 1.1 Features ......................................................................................................................... 1 1.2 System Block Diagram ................................................................................................. 6 1.3 2.5-inch Hard Disk Drive.............................................................................................. 9 1.4 Keyboard....................................
Chapter1 Hardware Overview Figures Figure 1-1-1 Left of the computer.......................................................................................... 4 Figure 1-2-1 System Block Diagram ..................................................................................... 6 Figure 1-3-1 2.5-inch HDD Disk Drive ................................................................................. 9 Figure 1-4-1 Keyboard for US Style..........................................................................
Chapter 1 Hardware Overview Features 1.1 Features The Satellite T130, Satellite Pro T130, PORTEGE T130 (Intel Platform) features are listed below. Microprocessor Microprocessor that is used will be different by the model. It supports processors as follows R CoreTM 2 Duo : SU7300 - Intel○ R CoreTM 2 Solo : SU3500 - Intel○ R Pentium○ R : SU4100, SU2700 - Intel○ Additional processors may be introduced.
Chapter 1 Hardware Overview Keyboard module has 85 or 86 keys. It supports Windows key and Application key. Battery The RTC battery is equipped inside the computer. The main battery is a detachable lithium ion battery. -6 cell 10.8V -12cell 10.8V USB (Universal Serial Bus) 3 USB ports are provided. The ports comply with the USB2.0 standard. USB Sleep and Charge function can be supported by only one port of the left side. (mode 1-4).
Chapter 1 Hardware Overview Some computers in this series offer Bluetooth wireless communication functionality. This module is Version 2.1+EDR. Wireless WAN Some models are equipped with a Wireless WAN module.
Chapter 1 Hardware Overview 11 10 9 5 6 7 12 13 8 1 4 2 3 1. External Monitor port 12.Power Button 2. HDMI out port 13. Security Lock 3. USB port (USB Sleep and Charge function is supported by this port only.) 4. FAN HOLE 5. Keyboard 6. Touch Pad 7. Touch Pad Control Right Button 8. Touch Pad Control Light Button 9. Display Screen 10. Web Camera 11.
Chapter 1 Hardware Overview 7 6 5 4 3 2 1. LAN jack 8. DC-IN jack 2. USB port 3. USB port 4. Microphone jack 5. Headphone Jack 6 Bridge Media Slot 7.
Chapter 1 Hardware Overview 1.2 System Block Diagram Figure 1-2-1 shows the system block diagram.
Chapter 1 Hardware Overview The PC contains the following components. CPU R CoreTM 2 Duo : SU7300 - Intel ○ R CoreTM 2 Solo : SU3500 - Intel ○ R Pentium○ R : SU4100, SU2700 - Intel○ Additional processors may be introduced. Memory Two memory slots capable of accepting DDR3-SDRAM 1GB, 2GB or 4GB memory modules for a maximum of 8GB(GS45 model) or 4GB(GS40 model). * 4GB memory module cannot be installed in GS40 model. 204-pin SO-DIMM 1.
Chapter 1 Hardware Overview RTC GPIO Enhanced Power Management SMBus 2.0 High Definition Audio Controller 569-pin 16mmx16mm mBGA Package Other main system chips Clock Generator (CULV Platform: ICS9LPRS365BKLFT) EC–[WO/CIR WPCE775CA0DG)] – HD Audio (CONEXANT CX20583-10Z) Card Reader controller (REALTEAK RTS5159 ) 10/100 LAN controller (Atheros AR8132M) Mini Card Wireless LAN (BTO) IEEE802.11b/g or IEEE802.11b/g/n Wireless WAN (BTO) HSPA Bluetooth Bluetooth V2.1+EDR.
Chapter 1 Hardware Overview 1.3 2.5-inch Hard Disk Drive A compact, high-capacity HDD with a height of 9.5mm. Contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-3-1 shows a view of the 2.5-inch HDD and Tables 1-3-2 and 1-3-3 list the specifications. Figure 1-3-1 2.5-inch HDD Standard value Parameter Outline dimens ions TOSHIBA MK2555GSX TOSHIBA MK3255GSX TOSHIBA MK4055GSX Width (mm) 69.85 +/- 0.25 Height (mm) 9.5 Depth (mm) 100.2 +/- 0.
Chapter 1 Hardware Overview Parameter Standard value WD2500BEVT-26ZCT0 WD3200BEVT-26ZCT0 100 Outline Width (mm) dimensi ons Height (mm) 12.5 Depth (mm) 70.
Chapter 1 Hardware Overview bus transfer rate (MB/s) 3Gbps 12.0ms/13.0ms Average random seek time (read) (ms) Power-on-to-ready (sec) 3.5 (typ.) Specification Parameter WD2500BEVT-26ZCT0 WD3200BEVT-26ZCT0 Storage size (formatted) 250GB 320GB Speed (RPM) Data transfer Rate - To/From Media - T0/From Host bus transfer rate (MB/s) Average random seek time (read/write)(ms) Power-on-to-ready (sec) 5,400 117MB/s Max. 3Gbps 3Gbps 12.0ms/13.0ms 4.0 (typ) Table 1-3-3 2.
Chapter 1 Hardware Overview 1.
Chapter 1 Hardware Overview 1.5 TFT Color Display The Satellite T130, Satellite Pro T130, and PORTEGE T130 use LED to control backlight. 1.5.1 LCD Module Figure 1-5-1 shows a view of the LCD module and Table 1-5-2 lists the specifications. Figure 1-5-1 SAMSUNG LCD Module Specifications(WXGA+) LG AUO LP133WH1 TLA1 B133XW02 V0 Number of Dots 1,366 x 3(R,G,B) x 768 1,366 x 3(R,G,B) x 768 Dot spacing (mm) 0.2148(H)× 0.2148(V) 0.2148(H)× 0.
Chapter 1 Hardware Overview 1.6 Power Rails Table 1-6-1 lists the power rail output specifications. Power supply （Yes/No） Name Voltage [V] Power OFF Suspend mode Power OFF Boot mode No Main Battery (with RTC Battery) +5VPCU 5 Yes Yes No +5V 5 No No No +3VPCU 3.3 Yes Yes No +3V_S5 3.3 Yes No No +3VSUS 3.3 Yes No No +3V 3.3 No No No +1.8VSUS 1.8 Yes No No +SMDDR_VTERM 1.8 Yes No No +SMDDR_VREF 1.8 Yes No No +1.8V 1.8 No No No +1.5V 1.5 No No No +1.
Chapter 1 Hardware Overview 1.7 Batteries The PC has the following two batteries. Main battery Real time clock (RTC) battery Table 1-7-1 lists the specifications for these two batteries. Battery Name Battery Element Output Voltage 6 Cell Li-ion 10.8v 12Cell Li-ion 10.8 v Coin type Li-ion 3.0v Main Battery RTC Battery Table 1-7-1 Battery specifications 1.7.1 Main Battery The main battery is the primary power supply for the computer when the AC adapter is not connected. 1.7.
Chapter 1 Hardware Overview Power ON Power OFF 6 cell 5 ~ 10 hours about 5 hours 12 cell 5 ~ 10 hours about 4 hours Table 1-7-2 Time required for charges of main battery Charge is stopped in the following cases. 1. The main battery is fully charged 2. The main battery is removed 3. Main battery or AC adapter voltage is abnormal 4. Charging current is abnormal Data retaining time When turning off the power in being charged fully, the retaining time is as following Table 1-7-3.
Chapter 1 Hardware Overview 1.7.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-7-4 lists the Time required for charges of RTC battery and data preservation time.
Chapter 1 Hardware Overview 1.8 AC Adapter Table 1-8-1 lists the AC adapter specifications. Parameter With Led Power Specification DELTA/ LITE-ON 3pin DELTA/ LITE-ON 2pin 65W 65W Input voltage AC 100V/240V Input frequency 50Hz/60Hz Input current ≦ 1.5A Output voltage DC 19V Output current 3.42A 3.
Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and PORTEGE T130 Maintenance Manual (960-Q08)
Chapter 2 Troubleshooting Procedures Chapter 2 Contents Chapter 2 Contents 2.1 Troubleshooting ............................................................................................................ 1 2.2 Troubleshooting Flowchart........................................................................................... 2 2.3 Power Supply Troubleshooting..................................................................................... 6 2.4 2.5 2.6 2.7 2.
Chapter 2 Troubleshooting Procedures 2.9 2.10 2.11 2.12 Procedure 3 Connector and Cable Check.................................................... 24 Procedure 4 Replacement Check ................................................................ 25 LAN Troubleshooting................................................................................................. 26 Procedure 1 Diagnostic Test Program Execution Check ............................
Chapter 2 Troubleshooting Procedures 2 2.1 Troubleshooting Chapter 2 describes how to determine which Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Power supply 6. Display 11. HDMI 2. System Board 7. LAN 3. SATA HDD 8. Wireless LAN 4. Keyboard 9. Sound 5. Touch pad 10. Bluetooth The Test Program operations are described in Chapter 3. Detailed replacement procedures are described in Chapter 4.
Chapter 2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-2-1 as a guide for determining which troubleshooting procedures to execute. Before going through the flowchart steps, verify the following: Ask customer to enter the password if a password is registered. Verify with the customer that Toshiba Windows is installed on the hard disk. NonWindows operating systems can cause the computer to malfunction.
Chapter 2 Troubleshooting Procedures Figure 2-2-1 Troubleshooting flowchart (1/2) Satellite T130, Satellite Pro T130 and PORTEGE T130Maintenance Manual (960-Q08)
Chapter 2 Troubleshooting Procedures Figure 2-2-1 Troubleshooting flowchart (2/2) If the diagnostics program cannot detect an error, the problem may be intermittent. The Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error(s), and then perform the appropriate troubleshooting procedures as follows: 1.
Chapter 2 Troubleshooting Procedures 4. If an error is found on the touch pad test, perform the Touch pad Troubleshooting Procedures in Section 2.7. 5. If an error is detected on the display test, perform the Display Troubleshooting Procedures in Section 2.8. 6. If an error is detected on the LAN test, perform the LAN Troubleshooting Procedures in Section 2.9. 7. If an error is detected on the Wireless LAN test, perform the Wireless LAN Troubleshooting Procedures in Section 2.10. 8.
Chapter 2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting The power supply controller controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed.
Chapter 2 Troubleshooting Procedures *1 When the power supply controller detects a malfunction, the DC IN icon blinks orange and perform the following procedure. When the icon is blinking, perform the following procedure. 1. Remove the battery pack and the AC adapter. 2. Re-attach the battery pack and the AC adapter. If the icon is still blinking after the operation above, check the followings: Check 1 If the DC IN icon blinks orange, go to Procedure 2.
Chapter 2 Troubleshooting Procedures Procedure 2 Connection Check The wiring diagram related to the power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord is firmly plugged into the PCN1 connector and wall outlet. If these cables are connected firmly, go to Check 2. Check 2 Replace the AC adapter and the AC power cord with new ones. Check 3 If the DC IN icon does not light, go to Procedure 4.
Chapter 2 Troubleshooting Procedures Check 5 Replace the battery pack with a new one. If the battery pack is still not charged, go to Procedure 4.
Chapter 2 Troubleshooting Procedures Procedure 4 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. To disassemble the computer, follow the steps described in Chapter 4, Replacement Procedures. When AC adapter is connected; Check 1 AC adapter may be faulty. Replace the AC adapter with a new one. If the problem still occurs, perform Check 2. Check 2 System board may be faulty.
Chapter 2 Troubleshooting Procedures 2.4 System Board Troubleshooting This section describes how to determine if the system board is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed.
Chapter 2 Troubleshooting Procedures Procedure 1 Message Check When the power is turned on, the system performs the Power on Self Test (POST) installed in the BIOS ROM. The POST tests each IC on the system board and initializes it. If an error message is shown on the display, perform Check 1. If there is no error message, go to Procedure 2. If Free-DOS or Windows is properly loaded, go to Procedure 4.
Chapter 2 Troubleshooting Procedures Procedure 2 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform these tests. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Hard Disk test 6. CPU Temperature test 7. Main Battery test 8. BIOS test 9. System Status LED test 10. Wireless LAN test 11. LAN/Sound test 12.
Chapter 2 Troubleshooting Procedures 2.5 SATA Hard Disk Drive Troubleshooting To check if HDD is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Partition Check Procedure 2: Message Check Procedure 3: Format Check Procedure 4: Diagnostic Test Program Execution Check Procedure 5: Connector Check and Replacement Check CAUTION: The contents of the hard disk will be erased when the HDD troubleshooting procedures are executed.
Chapter 2 Troubleshooting Procedures Procedure 2 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. Make sure no floppy disk is in the FDD. Turn on the computer and check the message on the screen. When an OS starts from the 2.5” HDD, go to Procedure 3. Otherwise, start with Check 1 below and perform the other checks as instructed.
Chapter 2 Troubleshooting Procedures Procedure 3 Format Check The computer’s HDD is formatted using the Free-DOS FORMAT program or the physical format program of the test program. To format the HDD, start with Check 1 below and perform the other steps as required. Refer to the Free-DOS Manual for the operation of Free-DOS. For the format by the test program, refer to the Chapter 3. Check 1 Format an 2.5” HDD using Free-DOS FORMAT command. Type as FORMAT C:/S/U. If 2.
Chapter 2 Troubleshooting Procedures Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnostics Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and statuses are described in Table 2-5-1.
Chapter 2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check HDD(s) is/are connected to the connector(s) on the system board. The connection of HDD(s) and board may be defective. Otherwise, they may be faulty. Disassemble the computer following instructions in Chapter 4, Replacement Procedures and perform the following checks. Check 1 Make sure HDD(s) is/are firmly connected to the connector(s) on the system board.
Chapter 2 Troubleshooting Procedures 2.6 Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Keyboard Test (DIAGNOSTIC TEST) and Pressed key display test in the Diagnostic Program.
Chapter 2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure keyboard cable is firmly connected to system board. If the connection is loose, reconnect firmly and repeat Procedure 1. If the problem still occurs, go to Check 2. Check 2 Keyboard may be faulty.
Chapter 2 Troubleshooting Procedures 2.7 Touch pad Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Touch pad test in the Diagnostic Program. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform the test program.
Chapter 2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the cable is firmly connected to system board. If the connection is loose, reconnect firmly and repeat Procedure 1. If the problem still occurs, go to Check 2.
Chapter 2 Troubleshooting Procedures 2.8 Display Troubleshooting To check if the computer’s display is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector and Cable Check Procedure 4: Replacement Check Procedure 1 External Monitor Check Connect an external monitor to the computer’s external monitor port, and then boot the computer.
Chapter 2 Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD cable. Their cables may be disconnected from system board. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. If the connection is loose, reconnect firmly and restart the computer. If the problem still occurs, go to Procedure 4.
Chapter 2 Troubleshooting Procedures Procedure 4 Replacement Check LCD module, LCD cable are connected to display circuits. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: If characters or graphics on the internal display are not displayed clearly, perform Check 1. If some screen functions do not operate properly, perform Check 2.
Chapter 2 Troubleshooting Procedures 2.9 LAN Troubleshooting To check if the computer’s LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute LAN test in the LAN test program. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program.
Chapter 2 Troubleshooting Procedures 2.10 Wireless LAN Troubleshooting To check if the computer's Wireless LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed.
Chapter 2 Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiring diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the wireless communication is Enabled in BIOS setup. If the Wireless communication is "Disabled", change it to "Enabled". If the problem still occurs, perform Check 2.
Chapter 2 Troubleshooting Procedures Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Wireless LAN antenna may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 2. Check 2 Wireless LAN card may be faulty.
Chapter 2 Troubleshooting Procedures 2.11 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check Procedure 2: Procedure 1 Replacement Check Connector Check The connection of sound system is shown in the following figure. As the connection may be defective, disassemble the PC and check each connection. If the problem still occurs, go to Procedure 2.
Chapter 2 Troubleshooting Procedures Procedure 2 Replacement Check If External microphone/Headphone does not work properly, perform check 1. If internal microphone /Speaker do not work properly, perform check 2. If HP out does not work properly, perform check 3. If Volume control does not work properly, perform check 4. Check 1 External microphone/Headphone may be faulty. Replace it with a new one following the steps in Chapter 4. If the problem still occurs, perform Check 5.
Chapter 2 Troubleshooting Procedures 2.12 Bluetooth Troubleshooting To check if the computer’s Bluetooth is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1 Connector Check and Replacement Check The Bluetooth module is connected to system board. If Bluetooth malfunctions, its connection is defective or Bluetooth cable and system board may be faulty. Check 1 Make sure Bluetooth cable is firmly connected to the connector CN12 (system board).
Chapter 2 Troubleshooting Procedures 2.13 HDMI Troubleshooting To check if the computer’s HDMI is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External HDMI Monitor Check Procedure 2: Connector and Cable Check Procedure 3: Replacement Check Procedure 1 Connector Check and Replacement Check The HDMI port is connected to system board. If HDMI malfunctions, its connection is defective or HDMI cable and system board may be faulty.
Chapter 2 Troubleshooting Procedures Procedure 3 Connector and Cable Check HDMI monitor connected to HDMI&USB board by an HDMI cable. If the connection is loose, reconnect firmly and restart the computer. If the problem still occurs, go to Procedure 4.
Chapter 2 Troubleshooting Procedures Procedure 4 Replacement Check HDMI signals are connected to display circuits via HDMI cable and HDMI&USB board. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: If characters or graphics on the internal display are not displayed clearly, perform Check 1. If some screen functions do not operate properly, perform Check 4.
Chapter 3 Diagnostic Programs Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)
Chapter 3 Test Program for Field Chapter 3 Contents 3.1 Tests and Diagnostics Software Overview ............................................................... 2 3.2 Executing the Diagnostic Test .................................................................................. 3 3.3 Subtest names............................................................................................................ 7 3.4 System Test.....................................................................................
Chapter 3 Test Program for Field Chapter 3 Diagnostic Programs Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)
Chapter 3 Test Program for Field 3.1 Tests and Diagnostics Software Overview This chapter explains how to use the Tests and Diagnostics Software for the Satellite T 130, Satellite Pro T130 and PORTEGE T130 computer systems. NOTES: Before starting the Tests and Diagnostics software: 1. Check all cables for loose connections. 2. Exit any application and close Windows.
Chapter 3 Test Program for Field 3.2 Executing the Diagnostic Test Free-DOS is required to run the Diagnostics Program. To start the programs follow these steps: 1. Create a Free-DOS bootable disk and copy all the files from the Tests and Diagnostics software to the disk. 2. Insert the boot disk into the computer’s floppy disk drive and turn on the computer. NOTES: If error message display “Sorry. This Model Type Not Match This Machine”: Please Check: 1. You test disk is match this model, ex.
Chapter 3 Test Program for Field The following menu displays: TOSHIBA Satellite(Pro) P500 Diagnostics Version V1.00 ESC ::Select item :Escape [DIAGNOSTICS MENU] 01. 02. 03. 04. 05. 01. 01. 06. 02. 99. 03. 04. 05. 06. 07. DIAGNOSTIC TEST RUNNING TEST DMI INFORMATION [DIAGNOSTIC TEST MENU] LOG UTILITIES SYSTEM CONFIGURATION SYSTEM TEST TEST 08. CACHE MEMORY TEST SYSTEM OPTION MEMORY TEST 09. HIGH RESOLUTION DISPLAY TEST EXIT KEYBOARD TEST 10. MULTIMEDIA TEST DISPLAY TEST 11.
Chapter 3 Test Program for Field 4. Select the subtest you want to execute and press Enter. The following menu displays: TOSHIBA Satellite(Pro) P500 Diagnostics Version V1.00 ESC : :Select item :Escape [DIAGNOSTICS MENU] [SYSTEM TEST] 01. DIAGNOSTIC TEST 02. RUNNING TEST 01. FAN ON/OFF 03. DMI INFORMATION 01. FAN ON/OFF 02.TEST Battery [DIAGNOSTIC MENU Test ] 04. LOG UTILITIES 03. CPU Temperature 05. SYSTEM CONFIGURATION DIAGNOSTIC TEST MENU 01. SYSTEM 01.OPTION SYSTEM TEST TEST 9. 99.
Chapter 3 Test Program for Field NOTES: The Item2 and 3 of Test Parameter are not used by some tests. Go To Test Move the highlight bar to Go to Test and press Enter to start executing the test. Test Loop Select NO to return the screen to the subtest menu after the test is complete. Select YES to set the test to run continuously until it is halted by the user. Error Stop Select NO to keep the test running even if an error is found.
Chapter 3 Test Program for Field 3.3 Subtest names Table 3-3-1 lists the subtest names for each test program in the Diagnostic Test menu. No. 01 02 03 04 Test Name SYSTEM TEST MEMORY TEST KEYBOARD TEST DISPLAY TEST No.
Chapter 3 Test Program for Field No. 05 06 07 08 09 Test Name No.
Chapter 3 Test Program for Field No. 10 11 Test Name No. MULTIMEDIA TEST MEMORY2 Subtest Name 01 Sequential Read Test 02 Random Read Test 03 Read Specified Address Test 04 1 point W/R/C Test 01 All one/zero Test 02 Walking 1/Walking 0 Test(Left) 03 Walking 1/Walking 0 Test(Right) 04 Walking 1/Walking 0 Test(Left /Right) Table 3-3-1 Subtest Names (3/3) *This test cannot support.
Chapter 3 Test Program for Field 3.4 System Test To execute the System Test select 01 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The System Test contains three subtests. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 FAN ON/OFF Checking Select 1,2,3 to control FAN on/off , 1=Fan on , 2=Fan off , 3=Exit . [BOIFAN2.EXE] Program Version: 1.
Chapter 3 Test Program for Field Subtest 03 CPU Temperature This will display CPU Temperature for check; press [ESC] to exit. [CPU_TEMP.EXE] Program Version: 1.3 03-09-2009 CPU Temperature: XX GPU Temperature: XX NOTES: If no external Graphics, GPU not report temperature. Subtest 04 3D HDD Protection Test (90d) 1. For Field inspection T&D. This program judges by sampling five kinds of data shown below. No Item 1 Access platform. Contents An access platform is leveling.
Chapter 3 Test Program for Field 3 Test1 The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test-Fixture contact is green. Set method of PC Z Upper X Judgment If all data is less than ranges, it will be OK.
Chapter 3 Test Program for Field 4 Test2 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Rear Upper Judgment If all data is less than ranges, it will be OK.
Chapter 3 Test Program for Field 5 Test3 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Right Upper Judgment If all data is less than ranges, it will be OK.
Chapter 3 Test Program for Field 6 Test4 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Front Upper Judgment If all data is less than ranges, it will be OK.
Chapter 3 Test Program for Field 7 Test5 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Left Upper 8 Inspection 9 Setting Calibration data Judgment If all data is less than ranges, it will be OK. Judgment If all data is less than ranges, it will be OK. When an inspection result is O.K., calibration at HPC. 2. Test Result A test result is displayed when a test is completed. A display of result is O.K. or NG.
Chapter 3 Test Program for Field 3.5 Memory Test To execute the Memory Test select 02 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Memory Test contains five subtests that test the computer’s memory. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the Test Status screen displays while the test is executing. When the test is complete the Memory Test menu displays.
Chapter 3 Test Program for Field 5. Address pattern test “16 bit write and 16 bit read” of address pattern data is executed and the new data is compared with the original data. Test data = 0000H, 0004H, 0008H, 000CH,...8000H, 8004H, through FFECH Subtest 02 Protected Mode This subtest first writes data patterns and address data from 1 to 32 MB, then reads the new data and compares the result with the original data patterns. Addresses are displayed in 64KB increments during the test. . Test Process: 1.
Chapter 3 Test Program for Field with the original data patterns. Addresses are displayed in 64KB increments during the test. Test Process: 1. Byte Enable Test One bit write/ 8 bit read” is executed and the new data is compared with the original data. Test data = CCAA5533H, 80000000H 2. Byte Enable Test “One bit write/16 bit read” is executed and the new data is compared with the original data. Test data = CCAA5533H, 80000000H 3.
Chapter 3 Test Program for Field Test Process: 1. Checks the memory size to determine the maximum size of installed memory. 2. Tests memory addresses 0 to the maximum installed. 3. Writes, reads, and compares test data after a memory refresh cycle (16ms or more). NOTE: There may be a short delay between write and read operations, depending on the memory size. Subtest 05 Stress Test This subtest writes the following 16KB data patterns to the Write/Read Buffer in conventional memory.
Chapter 3 Test Program for Field 3.6 Keyboard Test To execute the Keyboard Test select 03 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Keyboard Test contains five subtests that test the computer’s keyboard and mouse actions. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: The Test Loop and Error Stop parameters are not enabled for the Keyboard test.
Chapter 3 Test Program for Field Subtest 04 Hot Key Display [9 Key] This subtest is used for the 9 hot key and functions the same as Subtest 1. ECO MUTE MUSIC PLAY BACK NEXT VOL- VOL+ WLAN Subtest 05 Hot Key Display [1 Key] This subtest is used for the 1 hot key and functions the same as Subtest 1. WLAN Subtest 06 PS/2 Mouse (Pointing) This subtest checks the function of mouse as shown below.
Chapter 3 Test Program for Field LEFT PRESS TOUCH_PAD TEST RIGHT PRESS Please Do Not Press the Left and Right Button At The Same Time Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)
Chapter 3 Test Program for Field 3.7 Display Test To execute the Display Test select 04 from the Diagnostic Test Menu, press Enter and follow the directions displayed on the screen. The Display Test contains twelve subtests that test the display in various modes. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Character Attributes This subtest displays character attributes and color attributes.
Chapter 3 Test Program for Field Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES were selected for Test Loop on the Test Parameter Menu. Subtest 02 Character Set This subtest displays the character codes 00H - FFH, using Mode 01H (40*25). The screen below displays when this subtest is executed.
Chapter 3 Test Program for Field Subtest 03 80 * 25 Character Display This subtest uses 80*25 video resolution to display character codes 20H 7EH using Mode 03H (80*25). The data displayed is shifted 1 byte to the left for each line as shown below. 80*25 CHARACTER DISPLAY 01234567890123456789012345678901234567890123456789012345678901234567890123456789 !”#$%&’()*=,.-/0123456789:;?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_’abcdefghIjklmno !”#$%&’()*=,.
Chapter 3 Test Program for Field Subtest 04 320 * 200 Character Display This subtest uses 320*200 video resolution to display green, red and yellow followed by cyan, magenta, and white. The screen below shows the displays when this subtest is executed.
Chapter 3 Test Program for Field 320*200 GRAPHICS DISPLAY BLACK : [D] D GRAY BLUE L BLUE GREEN L GREEN CYAN L CYAN RED L RED MAGENTA L MAGENTA BROWN YELLOW WHITE I WHITE Press [Enter] KEY Press ENTER to display 64 gradations of red, green, blue and white on the screen 320*200 GRAPHICS DISPLAY : [13] 64 gradations of red are displayed. 64 gradations of green are displayed. 64 gradations of blue are displayed. 64 gradations of white are displayed.
Chapter 3 Test Program for Field Subtest 05 640 * 200 Character Display This subtest uses 640*200 video resolutions to display three windows; each window drives a different set of dots: even dots, odd dots and all dots. The screen below displays when this subtest is executed.
Chapter 3 Test Program for Field Subtest 06 640 * 480 Character Display This subtest uses 640*350 video resolutions to display 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
Chapter 3 Test Program for Field 640*480 GRAPHICS DISPLAY : [12 ] BLACK DARK GRAY BLUE LIGHT GREEN LIGHT GREEN CYAN LIGHT CYAN RED LIGHT RED MAGENTA LIGHT MAGENTA BROWN YELLOW WHITE INTENSIFIED WHITE BLUE Press [Enter] KEY To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES were selected for Test Loop on the Test Parameter Menu.
Chapter 3 Test Program for Field Subtest 07 Display Page This subtest displays video pages zero through seven. DISPLAY PAGE 0 000000000000000000000000000000000000000000000000000000000000000 0............................................................0 0............................................................0 0............................................................0 0............................................................0 0............................................................0 0.....
Chapter 3 Test Program for Field Subtest 08 "H" Pattern Display This subtest displays a full screen of "H" patterns.
Chapter 3 Test Program for Field Subtest 10 Color Graphics Display This subtest displays three colors, cyan, white and yellow on the screen as shown below. 640 * 480 GRAPHICS DISPLAY CYAN WHITE YELLOW To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES were selected for Test Loop on the Test Parameter Menu.
Chapter 3 Test Program for Field Subtest 11 Color Attributes Display This subtest displays 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
Chapter 3 Test Program for Field NOTE: The following screen does not display correctly. It will be amended in the next version. Press [Enter] Key Press Enter to execute the VRAM mapping test which displays a vertical line at four dot intervals using Mode 12. Press [Enter] Key Press Enter to display VRAM mapping test using the all dots Mode.
Chapter 3 Test Program for Field Press [Enter] Key To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES were selected for Test Loop on the Test Parameter Menu.
Chapter 3 Test Program for Field Subtest 12 Color Tiling This subtest displays black, gray, white, and 3 gradations of red, green, and blue as shown in the following display. Black Red Green Blue Gray Red Gradation Green Gradation Blue Gradation White Red Gradation Green Gradation Blue Gradation To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu.
Chapter 3 Test Program for Field 3.8 Floppy Disk Test CAUTION: Before running the floppy disk test, prepare a formatted work disk. Remove the diagnostics disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test select 05 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Floppy Disk Test contains five subtests that test the FDD. Move the highlight bar to the subtest you want to execute and press Enter.
Chapter 3 Test Program for Field Subtest 04 Write Specified Address NOTE: The first two digits of the ADDRESS indicate which track is being tested, the next two digits indicate the head, and the last two digits indicate the sector. This subtest allows you to verify the errors from Subtest 02. It writes specified data to a specified track and head. Use the Log Utilities (see Section 3.21) to specify the track number and head number where the error(s) occurred during Subtest 02.
Chapter 3 Test Program for Field 3.9 Hard Disk Test To execute the Hard Disk Test select 06 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Hard Disk Test contains eight subtests that test the functions of the hard disk drive. Move the highlight bar to the subtest you want to execute and press Enter. NOTES: The contents of the hard disk will be erased when subtest 02, 03, 04, 05, 07 or 08 is executed.
Chapter 3 Test Program for Field Subtest 04 Cross Talk and Peak Shift This subtest writes eight of the most likely to fail data patterns (shown below) to a cylinder on the HDD, and then reads the data while moving from cylinder to cylinder. Data Pattern B5ADADH 4A5252H EB6DB6H 149249H 63B63BH 9C49C4H 2DB6DBH D24924H Subtest 05 Write Specified Address NOTE: This subtest is designed to run with the Test Loop set to NO.
Chapter 3 Test Program for Field Subtest 07 Sequential Write This subtest writes specified data to all cylinders on the HDD. The following message displays on the screen to enter the test data. TEST DATA ????(=37b3H) Subtest 08 W-R-C Specified Address This subtest writes specified data to a specified sector count, then reads and compares the result. The following message displays on the screen to enter the test data, sector count.
Chapter 3 Test Program for Field 3.10 Real Time Clock Test To execute the Real Time Clock Test select 07 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Real Time Clock Test contains three subtests that test the computer’s real time functions. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Real Time This subtest allows you to change the date and time. To execute the Real Time Subtest, follow these steps: 1.
Chapter 3 Test Program for Field Subtest 02 Backup Memory This subtest writes 50 bytes of test data (FFH, AAH, 55H, and 00H) to the CMOS 14th address, then reads the new data and compares it to the original data. Subtest 03 Real Time Carry CAUTION: When this subtest is executed, the current date and time are reset. This subtest checks the clock’s carry function.
Chapter 3 Test Program for Field 3.11 Cache Memory Test To execute the Cache Memory Test select 08 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Cache Memory Test contains eight subtests that test the computer's cache memory. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the screen will remain blank while the subtest is executing.
Chapter 3 Test Program for Field Subtest 04 Bit Shift Pattern Test This subtest reads the contents of cache memory and saves it into RAM. The subtest then writes the bit shift data patterns (1 bit shifted every 4 bytes), reads the new data and compares the result with the original data. The original cache memory content is then restored to the cache memory. Subtest 05 Write Disturb Test (We can’t support this time) This subtest reads the contents of cache memory and saves it into RAM.
Chapter 3 Test Program for Field 3.12 High Resolution Display Test To execute the High Resolution Display Test select 09 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The High Resolution Display Test contains six subtests that test the computer's high resolution video display. Move the highlight bar to the subtest you want to execute and press Enter.
Chapter 3 Test Program for Field Subtest 02 640*480 Mode Display This subtest uses 640*480 video resolutions to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below.
Chapter 3 Test Program for Field Subtest 03 800 * 600 Mode Display This subtest uses 800*600 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 256 gradations of white, red, green, and blue as shown below.
Chapter 3 Test Program for Field Subtest 04 1024* 768 Mode Display This subtest uses 1024*768 video resolutions to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below.
Chapter 3 Test Program for Field Subtest 05 “H” Pattern Display This subtest uses the 1024*768 Mode to display a high resolution white frame, “H” letters (8*16 pixels fonts), at 128 letters by 48 lines.
Chapter 3 Test Program for Field Subtest 06 Focus Test (“E” Pattern) This subtest sets the 1024*768 Mode and displays “E” patterns (18*18 dot fonts), at 56 letters *42 lines surrounded by a high resolution white frame. To exit this subtest and return to the High Resolution Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES were selected for Test Loop on the Test Parameter Menu.
Chapter 3 Test Program for Field 3.13 Multimedia Test To execute the Multimedia Test select 10 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Multimedia Test contains four subtests that test the computer's multimedia functions. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: Use the Toshiba Backup CD-ROM for Subtests 01, 02, and 03. Because CDROM driver issue, the Multimedia function can’t test , this is limitation .
Chapter 3 Test Program for Field 3.14 MEMORY2 Test To execute the Expansion Test select 11 from the Diagnostic Test Menu, press Enter and Follow the directions on the screen. The MEMORY2 Test contains four subtests that test the computer's. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the Test Status screen displays while the test is executing. When the test is complete the Memory Test menu displays.
Chapter 3 Test Program for Field Tee test method is the same as Subtest2. However, the data to be used differs.
Chapter 3 Test Program for Field 3.15 Error Codes and Error Status Names The following table lists the error codes and error status names for the Diagnostic Tests.
Chapter 3 Test Program for Field Device Name HDD Cache Memory Multimedia Error Code Error Status Name BB Undefined Error CC Write Fault E0 Status Error F0 No Sense Error ?? Other Error 02 Protect Mode Error 03 Caching Error ?? Other Error 01 Write Error 0F Invalid Drive 15 Drive Not Ready ?? Other Error Table 3-15-1 Error codes and error status names (2/2) NOTE: If error status name is Other Error, please reference the Error Code for error information Satellite T130, Satellite
Chapter 3 Test Program for Field 3.16 Running Test NOTES: 1. You may add or delete subtests using the Running Test Edit Item function, see Section 3.20. 2. Do not forget to insert a work disk in the FDD. If a work disk is not inserted an error will be generated during the Floppy Disk Test. 3. If the test completes successfully a “PASS” sign with blue letters displays on the screen. 4. If the test fails or is interrupted before completion an “FAIL” sign with red letters displays on the screen. 5.
Chapter 3 Test Program for Field 3.17 DMI INFOEMATION Select 03 from the Diagnostics Menu and press Enter to Check or Write DMI Information Data: 3.17.1 Check DMI Information The Check DMI Configuration program contains the following configuration information for the computer: NOTE: Please set the media of DVD before starting a test. AHCI cannot control under the DOS System information (Type 1) 1. Manufacture : TOSHIBA 2. Product Name : Satellite XXXXXX 3. Version :(TOSHIBA Part Number) 4.
Chapter 3 Test Program for Field c. AC Adapter Select [1]65W [2]75W [3]95W [4]120W Select 1 ~ c to key in new data , select 0 to exit program , program will compare input data length with the max length , if over will retry key in Note: Please Check New DMI Information After System Restart!! V3.1 1. **** Manufacture Name ( TOSHIBA ) - (32) 2. **** Product Name ( Satellite XXXXXX ) - (32) 3. **** Part Number ( PSP50X-XXXXXX ) - (26) 4. **** Serial Number ( 12345678W ) - (32) 5.
Chapter 3 Test Program for Field 3.18 Log Utilities This function logs error information generated while a test is in progress and stores the results in RAM (Maximum error log: 500 times). This function can store data on a floppy disk. If the power switch is turned off, the error information will be lost. Error information is displayed in the following order: 1. 2. 3. 4. 5. 6. 7. 8.
Chapter 3 Test Program for Field 2. Error information displayed on the screen can be manipulated with the following number keys: The 1 key scrolls the display to the next page. The 2 key scrolls the display to the previous page. The 3 key returns to the Diagnostics Menu. The 4 key erases all error log information in RAM. The 5 key reads the log information from a floppy disk. The 6 key writes the log information to a floppy disk. The 7 key save the log information to a floppy disk.
Chapter 3 Test Program for Field 3.19 System Configuration Select 05 from the Diagnostics Menu and press Enter to display the following system configuration: SYSTEM CONFIGURATION : * * * * - * * * * * - BIOS VER = VX.XX KBC VER = XXXX MAC ADDRESS : XXXXXXXXXXXX 0 ASYNC ADAPTER 1 HDD DRIVE(S):XXXXXXXXXXXXXXXXXXXXXXXXXX FW Rev.:XXXXXXXX CUR LBA:XXXXXXXX ORG LBA:XXXXXXXX BATTERY TYPE:XXXXXXXXXX XXXMB MEMORY SIZE XXX CPU 1 Vedio Chip XXXXXXXXXXXXX 1 ODD DRIVE(S):XXXXXXXX FW Rev.
Chapter 3 Test Program for Field 3.20 Running Test Edit Item 3.20.1 Function Description Function description lets you add or delete the subtests used to execute the Running Test. The following screen displays after pressing the Tab key to edit an item in the Running Test. KEY OPERATION PgDn PgUp Home End Ins Del Enter Cursor Down Cursor Up Page Down Page Up Top of ITEM End of ITEM Insert ITEM Delete ITEM End 3.20.
Chapter 3 Test Program for Field 1. Enter a number or 0 for Loop Count and press Enter. Select a number from 1 to 65535 to define the number of times the Running Test executes. Select 0 to run the test continuously until halted by the user. 2. Select the NO or YES for Error Stop and press Enter. Select NO to keep the test running even if an error is found. Select YES to stop the test program when an error is found. NOTE: All errors which occur during execution of the Running Test are logged in the Log File.
Chapter 3 Test Program for Field 3.21 Common Tests and Operation 3.21.1 How to operate a window To input parameters, or open a window use the following keys. key [Enter] key [Esc] key : to move a highlight bar : to select an item at the highlight bar : to close the current window and go back to the previous window 3.21.2 How to Stop the Test Program To stop a test: [Ctrl]+[Break] Press the Ctrl key and the Break key simultaneously. 3.21.
Chapter 3 Test Program for Field 3.21.4 Pass Count Displays the number of times the test has been executed. Error Count Displays the number of errors which have occurred during the test. Write Data Displays only the test data that has failed to compare during the test while being written during the test. Read Data Displays test data that has failed to compare during the test while being read during the test. Test Address Displays the Test Address. (The format differs for each test.
Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)
Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130,and PORTEGE T130Maintenance Manual (960-Q08)
Chapter 4 Replacement Procedures Chapter 4 4.1 Contents Overview....................................................................................................................... 1 Safety Precautions ................................................................................................... 2 Before You Begin ................................................................................................... 3 Disassembly Procedure..............................................................
Chapter 4 Replacement Procedures Figures Figure 4-2-1 Remove the battery pack................................................................................. 9 Figure 4-2-2 Install the battery pack.................................................................................. 10 Figure 4-3-1 Turn the computer upside down ................................................................... 12 Figure 4-3-2 Remove HDD assembly...........................................................................
Chapter 4 Replacement Procedures Figure 4-10-3 Remove the touchpad and touchpad board…………………………………41 Figure 4-11-1 Remove the I/O Board .................................................................................. 43 Figure 4-12-1 Remove the system board ............................................................................. 45 Figure 4-12-2 Remove RTC battery-step_1 ........................................................................ 47 Figure 4-12-3 Remove RTC battery-step_2 ......
Chapter 4 Replacement Procedures 4 2 4.1 Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be removed before a particular FRU can be removed. The numbers in the chart indicate the relevant section numbers in this manual. In all cases when removing an FRU, the battery pack must also be removed.
Chapter 4 Replacement Procedures Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions while working on the computer. DANGER: 1. In the case of the battery, always use authentic parts or equivalent parts approved by Toshiba. Other batteries may have different specifications that are incompatible with the computer and may result in fire or explosion.
Chapter 4 Replacement Procedures Before You Begin Take note of the following points before starting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2 Battery Pack”. 1. Do not disassemble the computer unless it is operating abnormally. 2. Use the designated tools. 3. Ensure that the environment for working on and storing parts does not contain any of the following.
Chapter 4 Replacement Procedures Disassembly Procedure Three main types of cable connector are used. Pressure plate connector Spring connector Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cable out from the connector. When reconnecting a cable to a pressure plate connector, lift up the pressure plate to a suitable height and insert the cable into the connector.
Chapter 4 Replacement Procedures Assembly Procedure After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassembled. Take note of the following general points when assembling the computer. Take your time and follow the instructions carefully. Hurrying the assembly work will only introduce new problems.
Chapter 4 Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION: Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall out) causing a short circuit or other damage. NOTE: To tighten screws quickly and accurately, an electric screwdriver is recommended. M2 (2mm) 0.167 N·m (1.7 kgf·cm) M2.5 (2.5mm) 0.392 N·m(4.
Chapter 4 Replacement Procedures Screw Notation To make maintenance of the computer easier, markings of the kinds of the screws including the types and lengths are indicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw F: Thin head screw S: Super thin head screw T: Tapping screw U: Other screws (Unique screws: pan head, stud, etc.
Chapter 4 Replacement Procedures 4.2 Battery pack Removing the battery pack The following describes the procedure for removing the battery pack (See Figure 4-2-1). CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack. 1. Turn off the power of the computer. 2. Disconnect the AC adapter and all external devices from the computer. 3. Turn the computer upside down. 4.
Chapter 4 Replacement Procedures LATCH 2 LATCH 1 Figure 4-2-1 Remove the battery pack NOTE: Dispose of the used battery pack in accordance with the laws and ordinances of your local authority. Installing the battery pack The following describes the procedure for installing the battery pack (See Figure 4-2-2). CAUTION: There is a danger that the lithium ion battery pack may explode if not fitted, operated, handled, or disposed correctly.
Chapter 4 Replacement Procedures 3. Attach the battery cover to the battery pack. 4. Insert the battery pack 5.
Chapter 4 Replacement Procedures 4.3 HDD Removing a HDD-H9.5mm The following describes the procedure for removing the HDD (See Figure 4-3-1 to 4-3-3). CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause data loss or damage to the device. 1. Turn the computer upside down. 2. Remove the following screws with a T6-bit TORX securing a HDD slot cover and remove a HDD slot cover. M2.04.0B FPH(T6) screw x2 3. Remove the following screws securing the HDD assembly. M2.03.
Chapter 4 Replacement Procedures Figure 4-3-1 Turn the computer upside down CAUTION: When a HDD is installed, they are installed in the position as the following figure.
Chapter 4 Replacement Procedures 5. Remove the following screws securing the HDD holder and remove the HDD holder. M3.03.0B FLAT BIND screw x4 M3*3 4pcs Figure 4-3-3 Remove HDD Installing HDD-H9.5mm The following describes the procedure for installing the main HDD. 1. Install a HDD to the HDD holder and secure it with the following screws. M3.03.0F FLAT BIND screw x4 NOTE: Although they are 3mm head screws, screw torque must be set in 2.5kg-cm for four screws securing the HDD holder. 2.
Chapter 4 Replacement Procedures 4.4 Memory Module CAUTION: The power of the computer must be turned off when you remove a memory module. Remove a memory module with the power on risks damaging the module or the computer itself. Do not touch memory module terminals. Any dirt on the terminals may cause memory access problems. Never press hard or bend a memory module. Removing a memory module To remove a memory module, confirm that the computer is in boot mode.
Chapter 4 Replacement Procedures Figure 4-4-1 Remove memory slot cover Figure 4-4-2 Remove a memory module Satellite T130, Satellite Pro T130 , and PORTEGE T130Maintenance Manual (960-Q08)
Chapter 4 Replacement Procedures Installing a memory module To install a memory module, confirm that the computer is in boot mode. Then perform the following procedure (See Figure 4-4-3). 1. Insert a memory module into the connector of the computer slantwise (terminal side first) and press it to connect firmly. CAUTION: The power must be turned off when you insert a memory module. Inserting a memory module with the power on might damage the module or the computer itself.
Chapter 4 Replacement Procedures 4.5 Keyboard Removing the keyboard The following describes the procedure for removing the keyboard (See Figure 4-5-1 to 4-5-2). CAUTION: As the keycap may fall out, when handling the keyboard always hold it by the frame and do not touch the keycap. 1. Upside down the computer and remove the battery. 2. Loose the screws on KB holder. M2.0x2.0B Flat BIND screws x2 3. Open the display. 4. Insert your finger into the slot between the KB holder and the keyboard.
Chapter 4 Replacement Procedures Figure 4-5-1 Remove 2 screws for KB Holder Figure 4-5-2 Remove 2 screws for Keyboard Satellite T130, Satellite Pro T130 , and PORTEGE T130Maintenance Manual (960-Q08)
Chapter 4 Replacement Procedures Installing the keyboard The following describes the procedure for installing the keyboard. 1. Connect the keyboard flexible cable to the connector on the system board. 2. Slide and set the keyboard then secure it with the following screw. M2.03.0B FLAT BIND screw x2 3. Install the K/B holder by pressing it from the topside. 4. Upside down the computer and secure the KB holder with the following screw. M2.02.
Chapter 4 Replacement Procedures 4.6 Wireless LAN card and BT Module Removing a Wireless LAN card The following describes the procedure for removing a Wireless LAN card (See Figure 4-6-1 to 4-6-2). 1. Remove the screw of wireless LAN card. M2x 2.5 BIND screw x2 2. Disconnect the wireless LAN antenna cable from the connectors on a wireless LAN card. 3. Remove a wireless LAN card from the connector on the system board.
Chapter 4 Replacement Procedures Figure 4-6-2 Remove a wireless LAN card Satellite T130, Satellite Pro T130 , and PORTEGE T130Maintenance Manual (960-Q08)
Chapter 4 Replacement Procedures Installing a Wireless LAN card The following describes the procedure for installing a Wireless LAN card. 1. Insert a wireless LAN card terminals slantwise into the connector on the computer and press a wireless LAN card and lock the secure screws. 2. Connect the wireless LAN antenna cable to the terminals on a wireless LAN card. 3. Put the wireless LAN antenna cable on the right location from the guide.
Chapter 4 Replacement Procedures 4.7 3G module card Removing 3G module card The following describes the procedure for removing a 3G module card (See Figure 4-7-1 to 4-7-3). 1. Remove screw of 3G module board. M2x 3.0 BIND screw x2 2. Disconnect the 3G module antenna cable from the connectors on a 3G module card 3. Remove a 3G module card from the connector on the system board.
Chapter 4 Replacement Procedures Figure 4-7-2 Remove a 3G module card Satellite T130, Satellite Pro T130 , and PORTEGE T130Maintenance Manual (960-Q08)
Chapter 4 Replacement Procedures Installing a 3G module card The following describes the procedure for installing a 3G module card. (See Figure 47-3) 4. Insert a 3G module card terminals slantwise into the connector on the system board and press a 3G module card and lock the secure screws. 5. Connect the 3G module antenna cable to the terminals on a 3G module card. 6. Put the 3G module antenna cable on the bottom location from the guide.
Chapter 4 Replacement Procedures 4 4.8 Display Assembly Removing the display assembly The following describes the procedure for removing the display assembly (See Figure 4-8-1 to 4-8-5). 1. Close the display and turn the computer upside down. 2. Remove the battery pack (See Figure 4-2-1) 3. Open HDD Door Figure 4-8-1 Remove the screws (securing display assembly) 4. Remove the screws from the bottom side.
Chapter 4 Replacement Procedures Figure 4-8-2 Remove the screws (from bottom side) 5. Disassemble KB Holder and KB screw (See Figure 4-5-1) 6. Remove the screws from the top side and remove the cover.
Chapter 4 Replacement Procedures M2*5 7pcs Figure 4-8-3 Remove the screws (from top side) 7. Disconnect the FFC and cables. 8. Disassembly TOP ASSY 9. Pull out the wireless LAN antenna from the guide with two hands.
Chapter 4 Replacement Procedures Figure 4-8-4 Remove the Wireless Antenna and LCD cable 10. Pull out the LCD cables from the guide of system board.
Chapter 4 Replacement Procedures 11. Pull out the LCD cables from the guide of LCD panel.
Chapter 4 Replacement Procedures Opening the display to 135degree, keeping display side by hand and remove the hinge screw. ‧ M2.54 FLAT BIND screw x4(Lock tight) ‧ M2.05 FLAT BIND screw x2(Lock tight) M2*5 2pcs M2.5*4 4pcs Figure 4-8-7 Remove the hinge screws 12. Remove the display assembly with two hands holding from the base assembly.
Chapter 4 Replacement Procedures Installing the display assembly The following describes the procedure for installing the display assembly. 1. Inserting the pole of hinge to the hole of hinge assembly, set the display assembly with hands on the base assembly. 2. Secure the hinges with the following screws secure the display mask with the following screws and stick the mask seal on them. ‧ M2.54 FLAT BIND screw x4(Lock tight) ‧ M2.05 FLAT BIND screw x2(Lock tight) M2.5*4 4pcs M2.
Chapter 4 Replacement Procedures 3. Connect the LCD harness to the connector on the system board. Figure 4-8-9 Connecting LCD harness to the system board 4. Arrange the wireless antenna cables along the guide (front) and secure them with guide. 5. Pass the cables to the back of computer through the slot. 6. Arrange the Wireless LAN antenna along the guide and contact with the connector with hands.
Chapter 4 Replacement Procedures Figure 4-8-10 Arrange and connect Wireless LAN cable 7. Install the LAN board and cover ASSY of the system. NOTE: If Fingerprint or Dust left on LCD screen during disassembly and assembly LCD units, please follow Appendix A to clean it.
Chapter 4 Replacement Procedures 4.9 Cover Assembly Removing the cover assembly The following describes the procedure for removing the cover assembly (See Figure 4-9-1 to 4-9-3). 1. Turn over the computer. 2. Remove the following screws securing the cover assembly from the back and bottom of computer. M2-0.42 FLAT BIND screw Back x6 M2.56.5 FLAT BIND screw Back x2 M2.05.0 FLAT BIND screw Back x11 M2-0.4*2 6pcs M2.5*6.5 2pcs M2.0*5.
Chapter 4 Replacement Procedures 3. Remove the following screws securing the cover assembly from the front of computer. Pull up and remove the cover assembly from the base assembly. M2.05.0 FLAT BIND screw Back x11 M2*5 7pcs Figure 4-9-2 Remove the screws (front) and cover assembly 4. Disconnect the touch pad flat cable/LAN cable/Power cable from the connector on the system board.
Chapter 4 Replacement Procedures Figure 4-9-3 Disconnect the touch pad flat cable/LAN cable Satellite T130, Satellite Pro T130, and PORTEGE T130Maintenance Manual (960-Q08) 4-37
Chapter 4 Replacement Procedures Installing the cover assembly The following describes the procedure for installing the cover assembly. 1. Install the cover assembly to the base assembly. NOTE: Be careful not to catch the cables between cover assembly and base assembly. 2. Connect the touch pad flat cable to the connector on the system board. 3. Secure the cover assembly with the following screws from the back and bottom of computer. M2-0.42 FLAT BIND screw Back x6 M2.56.
Chapter 4 Replacement Procedures 4.10 Touch Pad Removing the touch pad The following describes the procedure for removing the touch pad (See Figure 4-10-1 to 410-3). 1. Peel off the glass tape and disconnect the touch pad flat cable, Fingerprint cable from the connector on the touch pad. 2. Remove the following screws securing the touch pad plate. M2x2-I SUPER THIN HEAD screw x6 M2-0.4x2 SUPER THIN HEAD screw x2 M2.0x3.0 SUPER THIN HEAD screw x2 3.
Chapter 4 Replacement Procedures Figure 4-10-1 Remove the touch FFC cable Satellite T130, Satellite Pro T130, and PORTEGE T130Maintenance Manual (960-Q08) 4-40
Chapter 4 Replacement Procedures M2*2-I 5pcs M2-0.4*2 2pcs M2.0*3.
Chapter 4 Replacement Procedures Installing the touch pad The following describes the procedure for installing the touch pad. 1. Peel off the separator covering on the sensor portion of a new touch pad. NOTE: Do not reuse the touch pad so that it can not be used after peeling off from the computer. Be sure to stick a new touch pad. When sticking the touch pad, be careful not to get the bubbles under the touch pad. 2. Stick and install the touch pad on the cover assembly. 3.
Chapter 4 Replacement Procedures 4.11 I/O Board The following describes for removing the cover assembly (See Figure 4-11-1). Removing the I/O Board 1. Pull out the I/O Board FFC, LAN FFC, Speaker cable from I/O board connector. 2. Loose the below screws and then incline pull out I/O Board. M2.0x3.
Chapter 4 Replacement Procedures Installing the I/O Board 1. Insert the I/O Board FFC, LAN FFC, Speaker cable into base case and connect I/O board cable and speaker cable 2. Fix the below screws then incline insert in I/O Board M2.0x3.0 FLAT BIND screw x2 NOTE: Be careful not to catch the cables between cover assembly and base assembly.
Chapter 4 Replacement Procedures 4.12 System board CAUTION: 1. when handling the system board, always hold by the edges. Do not touch the printed circuit face. 2. if replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configuration”. Removing the system board The following describes the procedure for removing the system board (See Figure 4-12-1). 1.
Chapter 4 Replacement Procedures Installing the system board The following describes the procedure for installing the system board. 1. Secure the system board with the following screws. M2.03 screw x2 2. Connect the LAN FFC, LCD CABLE, ANTENNA, I/O board FFC, USB FFC, CRT cable, BT wire, SIM FFC, TP board FFC, Power Board FFC, DC-IN cable to the connector on the system board. 3. Connect the power cable to the connector on the system board.
Chapter 4 Replacement Procedures Removing RTC battery The following describes the procedure for removing the RTC battery unit (See Figure 4-12-2 to 4-12-3). 1. Pull the away the socket of RTC battery and use a clamp to hold RTC battery tightly. 2. Rotate battery through the way then remove it.
Chapter 4 Replacement Procedures Figure 4-12-3 Remove the RTC battery-step_2 Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) 48
Chapter 4 Replacement Procedures Installing RTC battery The following describes the procedure for installing the RTC battery unit (See Figure 4-12-4). 1. Press the force vertically then lock the RTC battery tightly.
Chapter 4 Replacement Procedures 4.13 CPU Removing the CPU heat sink The following describes the procedure for removing the CPU heat sink (See Figure 4-13-1). 1. Disconnect the Heat sink cable from the connector on the system board 2. Remove the following screws securing the heat sink holder along 1 to 3. M2.03.0 screw x3 NOTE: When removing the heat sink holder, be sure to remove the screws in the reverse order of the number marked on the holder.
Chapter 4 Replacement Procedures Installing the CPU heat sink The following describes the procedure for installing the CPU heat sink 1. Secure the following screws securing the heat sink holder along 1 to 3. 2. M2.03.
Chapter 4 Replacement Procedures 4.14 LCD unit Removing the LCD unit The following describes the procedure for removing the LCD unit (See Figure 4-14-1 to 414-3). 1. Remove Screw MYLAR cover x4 2. Remove the following screws securing the display mask M2.05 screw x4 3. Insert your finger between the edge of the display mask and the LCD, and remove the display mask while releasing the latches of display mask.
Chapter 4 Replacement Procedures Figure 4-14-2 Remove the LCD unit Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) 53
Chapter 4 Replacement Procedures 7. Remove the following screws securing the LCD support (LCD unit side) and remove the hinge from the LCD unit. M2.0x2.
Chapter 4 Replacement Procedures Installing the LCD unit The following describes the procedure for installing the LCD unit. Install the LCD supports (LCD unit side) and hinge to the LCD and secure them with the following screws. M2.02.5 BINK screw x4 1. Stand the LCD unit on the display cover and connect the LCD harness to the connector on the back of LCD. 2. Stick the kapton tape on the connector of LCD harness. 3. Secure the LCD unit with the following screws. M2.0x3.0 screw x6 4.
Chapter 4 Replacement Procedures 4.15 Web Camera module Removing Web Camera module The following describes the procedure for removing the Web Camera module. (See Figure 4-15-1 to 4-15-2). 1. Pull off the connector of Web Camera module. 2. Peel off the glue of Web Camera module.
Chapter 4 Replacement Procedures Figure 4-15-2 Peel off the glue of Web Camera module Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) 57
Chapter 4 Replacement Procedures Installing Web Camera module The following describes the procedure for removing the Web Camera module. 1. Connect the connector of Web Camera module. 2. Pull in the glue of Web Camera Module.
Chapter 4 Replacement Procedures 4.16 Application for Thermal grease on CPU and North Bridge (See Figure 4-16-1) I.
Chapter 4 Replacement Procedures II. Use grease on North Bridge and CPU 0.15cc for one repair.
Chapter 4 Replacement Procedures 4.17 Speaker Box Removing Speaker Box The following describes the procedure for removing Speaker Box. (See Figure 4-17-1 to 417-3). 1. Remove the following screws securing Speaker Box. 2. M2.02.5 screw x 4 Removing the Speaker Box. Figure 4-17-1 Removing the securing screws at left side.
Chapter 4 Replacement Procedures Figure 4-17-2 Removing the securing screws at right side Figure 4-17-3 Removing the Speaker Box.
Chapter 4 Replacement Procedures Installing Speaker Box The following describes the procedure for removing Speaker Box. 1. Installing the Speaker Box. 2. Securing Speaker Box of following screws. M2.02.
Appendices Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)
Appendix Contents Appendix A Handling the LCD Module............................................................................. 1 Appendix B Board Layout................................................................................................... 1 B.1 System Board .................................................................................................... 1 B.2 Touch Pad Board............................................................................................... 4 B.
C.16 CN22 WLAN Connectors............................................................................... 9 C.17 CN19 DDR Connectors………………...………………….………………10 C.18 CN20 DDR2 Connectors…………………………………………………….14 Appendix D Display Codes .................................................................................................. 1 D.1 Display Codes ................................................................................................... 1 Appendix E Keyboard Layout .........................
Appendix F Wiring Diagrams..........................................................................................F-1 F.1 RGB Monitor ID Wraparound Connector .................................................... F-1 F.2 LAN Loopbak Connector ..............................................................................
Handling the LCD Module Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
Handling the LCD Module 3. If the panel’s surface gets fingerprint or dust, put on gloves and wipe it with static electricity cloth. If it is still dirty, drop some cleaning alcohol on the surface and wipe it again. If the surface is much more fingerprint or dust, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. If dust still exists, please use ionic FAN which can avoid static electricity to deal with it. 4.
Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.
Handling the LCD Module Satellite T130, Satellite Pro T130, and PORTEGE T130Maintenance Manual (960-Q08)
Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
Handling the LCD Module 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization.
Board Layout Appendix B Appendix B Board Layout B.
Board Layout 17 15 14 13 24 18 20 23 19 27 10 21 22 24 Figure B-1-2 System board layout (Back) NUM Location Function (01) CN1 LVDS CONN (02) CN2 POWER BOARD CONN (03) CN3 KB CONN (04) CN4 LAN CONN Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Manual (960-Q08)
Board Layout (05) CN5 11” HDD CONN (06) CN6 TP CONN (07) CN7 ODD CONN (08) CN8 3G CONN (09) CN9 AUDIO&LAN&USB*2 CONN (10) CN10 RTC CONN (11) CN11 HDMI&USB*1 CONN (12) CN12 BT CONN (13) PCN1 AC-IN CONN (14) CN14 BATTERY CONN (15) CN15 FAN CONN (16) CN16 CTR CONN (17) U9 (18) CN18 HDD CONN (19) CN19 DDR CONN (20) CN20 DDR CONN (21) CN21 3G CONN (22) CN22 WLAN CONN (23) U3 LAN IC (24) U15 CPU (25) U14 NB (26) U20 SB (27) U18 CLOCK GEN EC IC T
Board Layout B.
Board Layout 02 01 Figure B-2-3 Touch Pad board layout (Back) NUM Location Function (01) CN2 TP Board to TP Module CONN (02) CN3 TP Board to M/B CONN Table B-2-4 Touch Pad board connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Manual (960-Q08)
Board Layout B.
Board Layout B.
Board Layout 02 03 01 Figure B-4-3 HDMI Board layout (Front) Location Function (01) U17 HDMI LEVEL SHIFT IC (02) CN1 HDMI CONN (03) CN4 USB CONN Table B-4-4 HDMI Board connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Manual (960-Q08)
Board Layout B.
Board Layout B.
Board Layout (07) CN8 External MIC CONN (08) CN6 Earphone CONN Table B-6-2 Audio&Lan&Usb&Card Reader Board IC Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Manual (960-Q08)
Board Layout B.
Board Layout B.
Board Layout B.
Pin Assignment Appendix C Pin Assignment CN1 LCD Panel Connectors PIN No. Signal name I/O PIN No.
Pin Assignment 5 GND --- 6 CRT_DDCDAT I/O 7 CRT_VSYNC I 8 CRT_DDCCLK I/O 9 CRT_HSYNC I 10 GND --- 11 GND --- 12 CRT_RED I 13 CRT_GREEN I 14 GND --- 15 GND --- 16 CRT_BLUE I CN2 LAN Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 AVDD_CEN --- 2 TX1P --- 3 TX1N --- 4 GND --- 5 TX0P --- 6 TX0N --- CN8 LAN Connectors PIN No. Signal name I/O PIN No.
Pin Assignment CN6 Power Board Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 +5VPCU I 2 NBSWON# I 3 PWRLED# I 4 GND --- CN3 Keyboard Connectors PIN No. Signal name I/O PIN No.
Pin Assignment 33 FN_F10 O 34 NUMLED O CN6 Touchpad Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 GND --- 3 GND --- 4 LID591# O 5 TPCLK I 6 TPDATA I 7 MMC)LED# --- 8 3G_WIMAX_LED# --- 9 RF_LED I 10 SATA_LED#_C --- 11 BAT_SAT1 I 12 BAT_SAT0 I 13 SUSLED_EC I 14 PWERLED# I 15 ACIN I 16 +3V --- 17 +3VPCU --- 18 +5V --- PIN No. Signal name CN5 Audio&USB&Lan&Card reader Board Connectors PIN No.
Pin Assignment 15 GND --- 16 USBP0+ I/O 17 USBP0- I/O 18 GND --- 19 USBP1+ I/O 20 USBP1- I/O 21 GND --- 22 USB_EN#0_1 I 23 +3V --- 24 +1.5V --- 25 +5V --- 26 +5V --- 27 +5V --- 28 +5VPCU --- 29 +5VPCU --- 30 +5VPCU --- 31 +5VPCU --- 32 +5VPCU --- 33 MMC_LED# --- 34 PLTRST# I 35 GND --- 36 USBP4+ I/O 37 USBP4- I/O CN12 Blue Tooth Connectors PIN No. Signal name I/O PIN No.
Pin Assignment 1 RTC_NO2 I 2 GND --- CN18 SATA HDD Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 SATA_TXP0_R I/O 3 SATA_TXN0_R I/O 4 GND --- 5 SATA_RXN0_R I/O 6 SATA_RXN0_R I/O 7 GND --- 8 +3V --- 9 +3V --- 10 +3V --- 11 GND --- 12 GND --- 13 GND --- 14 +5V --- 15 +5V --- 16 +5V --- 17 GND --- 18 NC --- 19 GND --- 20 NC --- 21 NC --- 22 NC --- CN11 HDMI Connectors PIN No. Signal name I/O PIN No.
Pin Assignment 11 NC --- 12 BUSBP9- I/O 13 BUSBP9+ I/O 14 GND --- 15 USBOC9# O 16 USB_SLEEP_EN# I 17 BOARD_ID4 O 18 PORT-B_HPD# --- 19 SDVO_CTRLDATA O 20 SDVO_CTRLCLK O 21 GND I 22 TMDSB_CLK# I 23 TMDSB_CLK I 24 GND --- 25 TMDSB_DATA0# I 26 TMDSB_DATA0 I 27 GND --- 28 TMDSB_DATA2# I 29 TMDSB_DATA2 I 30 GND --- 31 TMDSB_DATA1# I 32 TMDSB_DATA1 I CN15 FAN Connectors PIN No. Signal name I/O 1 TH_FAN_POWER1 --- 3 FANSIG1 O PIN No.
Pin Assignment 9 MBAT+ --- 11 GND --- 10 GND --- CN21 3G Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 3G_WAKE# O 2 +3V --- 3 NC --- 4 GND --- 5 NC --- 6 +1.
Pin Assignment 41 +3V_3G --- 42 3G_LED# --- 43 NC --- 44 NC --- 45 NC --- 46 NC --- 47 NC --- 48 +1.5V_3G --- 49 NC --- 50 GND --- 51 NC O 52 +3V_3G --- CN22 WLAN Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 WLAN_WAKE# O 2 +3V --- 3 WCS_DATR --- 4 GND --- 5 WCS_CLKR --- 6 +1.
Pin Assignment 33 PCIE_TXP6 I 34 GND --- 35 GND --- 36 USBP10- I/O 37 GND --- 38 USBP10+ I/O 39 NC --- 40 GND --- 41 NC --- 42 WIMAX_LED# --- 43 GND --- 44 NC --- 45 CL_CLK1_WLAN --- 46 NC --- 47 PLTRST#_PCIE --- 48 +1.5V --- 49 CL_RST#1_WLAN --- 50 GND --- 51 NC O 52 WIMAX_P --- CN19 DDR Connectors PI N No. Signal name I/O PIN No.
Pin Assignment 25 GND --- 26 GND --- 27 M_B_DQS#1 I/O 28 M_B_DM1 I/O 29 M_B_DQS1 I/O 30 DDR3_DRAMRS T# I 31 GND --- 32 GND --- 33 M_B_DQ11 I/O 34 M_B_DQ14 I/O 35 M_B_DQ10 I/O 36 M_B_DQ15 I/O 37 GND --- 38 GND --- 39 M_B_DQ16 I/O 40 M_B_DQ20 I/O 41 M_B_DQ21 I/O 42 M_B_DQ17 I/O 43 GND --- 44 GND --- 45 M_B_DQS#2 I/O 46 M_B_DM2 I/O 47 M_B_DQS2 I/O 48 GND --- 49 GND --- 50 M_B_DQ18 O 51 M_B_DQ22 I/O 52 M_B_DQ23 I/O 53 M_B_DQ19
Pin Assignment 77 NC --- 78 NC --- 79 M_B_BS#2 I 80 M_B_A14 I 81 +1.5VSUS --- 82 +1.5VSUS --- 83 M_B_A12 I 84 M_B_A11 I 85 M_B_A9 I 86 M_B_A7 --- 87 +1.5VSUS --- 88 +1.5VSUS --- 89 M_B_A8 I/O 90 M_B_A6 I/O 91 M_B_A5 I/O 92 M_B_A4 I/O 93 +1.5VSUS --- 94 +1.5VSUS --- 95 M_B_A3 I/O 96 M_B_A2 I/O 97 M_B_A1 I/O 98 M_B_A0 I/O 99 +1.5VSUS --- 100 +1.
Pin Assignment 129 M_B_DQ32 I/O 130 M_B_DQ36 I 131 M_B_DQ37 I/O 132 M_B_DQ33 I/O 133 GND --- 134 GND --- 135 M_B_DQS#4 I/O 136 M_B_DM4 I/O 137 M_B_DQS4 I/O 138 GND --- 139 GND --- 140 M_B_DQ38 I/O 141 M_B_DQ34 I/O 142 M_B_DQ39 I/O 143 M_B_DQ35 I/O 144 GND --- 145 GND --- 146 M_B_DQ44 I/O 147 M_B_DQ41 I/O 148 M_B_DQ45 I/O 149 M_B_DQ40 I/O 150 GND --- 151 GND I/O 152 M_B_DQS#5 I/O 153 M_B_DM5 155 GND I/O 154 M_B_DQS5 I/O --- 156
Pin Assignment 181 M_B_DQ56 I/O 183 M_B_DQ57 I/O 185 GND --- 187 M_B_DM7 189 182 M_B_DQ61 I/O GND --- 186 M_B_DQS#7 I/O I/O 188 M_B_DQS7 I/O GND --- 190 GND --- 191 M_B_DQ60 I/O 192 M_B_DQ58 I/O 193 M_B_DQ62 I/O 194 M_B_DQ63 I/O 195 GND --- 196 GND --- 197 SA0 I/O 198 PM_EXTTS#1 -- 199 +3V --- 200 CGDAT_SMB I/O 201 SA0 --- 202 CGCLK_SMB I/O 203 +SMDDR_VTERM I/O 204 +SMDDR_VTER M I/O 184 CN20 DDR Connectors PI N No.
Pin Assignment 23 M_A_DQ8 I/O 24 M_A_DQ13 I/O 25 GND --- 26 GND --- 27 M_A_DQS#1 I/O 28 M_A_DM1 I/O 29 M_A_DQS1 I/O 30 DDR3_DRAMRS T# I 31 GND --- 32 GND --- 33 M_A_DQ9 I/O 34 M_A_DQ14 I/O 35 M_A_DQ10 I/O 36 M_A_DQ11 I/O 37 GND --- 38 GND --- 39 M_A_DQ23 I/O 40 M_A_DQ17 I/O 41 M_A_DQ18 I/O 42 M_A_DQ21 I/O 43 GND --- 44 GND --- 45 M_A_DQS#2 I/O 46 M_A_DM2 I/O 47 M_A_DQS2 I/O 48 GND --- 49 GND --- 50 M_A_DQ20 I/O 51 M_A_DQ22
Pin Assignment 75 +1.5VSUS --- 76 +1.5VSUS --- 77 NC --- 78 NC --- 79 M_A_BS#2 I 80 M_A_A14 I 81 +1.5VSUS --- 82 +1.5VSUS --- 83 M_A_A12 I 84 M_A_A11 I 85 M_A_A9 I 86 M_A_A7 --- 87 +1.5VSUS --- 88 +1.5VSUS --- 89 M_A_A8 I/O 90 M_A_A6 I/O 91 M_A_A5 I/O 92 M_A_A4 I/O 93 +1.5VSUS --- 94 +1.5VSUS --- 95 M_A_A3 I/O 96 M_A_A2 I/O 97 M_A_A1 I/O 98 M_A_A0 I/O 99 +1.5VSUS --- 100 +1.
Pin Assignment 127 GND --- 128 GND --- 129 M_A_DQ32 I/O 130 M_A_DQ34 I 131 M_A_DQ37 I/O 132 M_A_DQ39 I/O 133 GND --- 134 GND --- 135 M_A_DQS#4 I/O 136 M_A_DM4 I/O 137 M_A_DQS4 I/O 138 GND --- 139 GND --- 140 M_A_DQ33 I/O 141 M_A_DQ36 I/O 142 M_A_DQ38 I/O 143 M_A_DQ35 I/O 144 GND --- 145 GND --- 146 M_A_DQ47 I/O 147 M_A_DQ41 I/O 148 M_A_DQ45 I/O 149 M_A_DQ40 I/O 150 GND --- 151 GND I/O 152 M_A_DQS#5 I/O 153 M_A_DM5 I/O 154 M_A_
Pin Assignment 179 GND --- 181 M_A_DQ63 I/O 183 M_A_DQ56 I/O 185 GND --- 187 M_A_DM7 189 180 M_A_DQ57 I/O M_A_DQ60 I/O GND --- 186 M_A_DQS#7 I/O I/O 188 M_A_DQS7 I/O GND --- 190 GND --- 191 M_A_DQ59 I/O 192 M_A_DQ62 I/O 193 M_A_DQ61 I/O 194 M_A_DQ58 I/O 195 GND --- 196 GND --- 197 SA0 I/O 198 PM_EXTTS#0 -- 199 +3V --- 200 CGDAT_SMB I/O 201 SA0 --- 202 CGCLK_SMB I/O 203 +SMDDR_VTERM I/O 204 +SMDDR_VTER M I/O 182 184 Satellite T130,
Display Codes Appendix. D Appendix D Display Codes D.1 Display Codes Cap No.
Display Codes Cap No.
Display Codes Cap No.
Display Codes Cap No. Keytop 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0 2F E0 F0 2F Code set 1 Make Code set 2 Break Make Note Break Table D-1-1 Scan codes (set 1 and set 2) (4/4) Notes: 1. 2. 3. 4. 5. 6. 7. * * * * * * * Scan codes differ by mode. Scan codes differ by overlay function.
Display Codes Cap Key Code set 1 No.
Display Codes Cap Key Code set 1 No.
Display Codes Cap No. Code set 1 Keytop Code set 2 Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F0 72 39 L (3) 51 D1 7A F0 7A 40 ; (+) 4E CE 79 F0 79 52 M (0) 52 D2 70 F0 70 54 . (.
Display Codes Key top Pause Shift Code set 1 Code set 2 Make Make Common* E1 1D 45 E1 Ctrl* E0 C6 E0 46 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E Table D-1-7 No.126 key scan code *: This key generates only make codes.
Keyboard Layout Appendix E Keyboard Layout 1. United Status (US) Keyboard Figure E-1-1 US keyboard 2.
Keyboard Layout 3.
Wiring Diagrams Appendix F Appendix F F.1 Wiring Diagrams RGB Monitor ID Wraparound connector Figure F-1-1 RGB Monitor ID Wraparound connector (15PIN to 15PIN) F.
