Portégé® M200/M205 Series User’s Guide If you need assistance: ❖ Toshiba’s Support Website pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 191 in this guide.
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Model: Portégé ® M200/M205 Series Recordable and/or ReWritable Drive(s) and Associated Software Warranty The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available.
Critical Applications The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interference received, including interference that may cause undesired operation. Contact either: ❖ Toshiba’s Support Website at pcsupport.toshiba.com.
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can.
provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer. Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Finnish: Dutch: French: Swedish: Danish: German: Valmistaja TOSHIBA Corp. Digital Media Network Company vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart TOSHIBA Corp. Digital Media Network Company dat het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze TOSHIBA Corp.
Spanish: Portuguese: Por medio de la presente TOSHIBA Corp. Digital Media Network Company declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. TOSHIBA Corp. Digital Media Network Company declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. USA – Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules.
Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
Using this Equipment in Japan In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on devices incorporating this product. 2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4DSOF4 (4) 1 2.
Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.
802.11b (2.4 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ Belgique: Deutschland: France: Italia: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required.
E’necessaria la concessione ministeriale anche per l’uso interno. Nederland: Verificare con i rivenditori la procedura da seguire. License required for outdoor installations. Check with reseller for procedure to follow. Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure. 802.
❖ To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply. The user should use the wireless LAN utility to check the current channel of operation. If operation is occurring outside of the allowable frequencies as listed above, the user must cease operating the Wireless LAN at that location and consult the local technical support staff responsible for the wireless network.
802.11b (2.4 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA 802.
Mexico Norway Singapore Switzerland USA Netherlands Peru Spain UK Venezuela New Zealand Portugal Sweden Uruguay Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Bluetooth® wireless technology Interoperability Bluetooth® Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖ Bluetooth Specification as defined and approved by The Bluetooth Special Interest Group. ❖ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special Interest Group.
Bluetooth® wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
NOTE Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment. Taiwan Article 14 Article 17 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.
2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4FH1 (4) 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3.
The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. DVD-ROM, multi-function drive safety instructions The DVD-ROM and multi-function drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Never attempt to disassemble, adjust or repair a CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive.
Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. ©2005 by Toshiba America Information Systems, Inc. All rights reserved. Export Administration Regulation This document contains technical data that may be controlled under the U.S.
Trademarks Portégé is a registered trademark, FreedomWare, and SmartMedia are trademarks, of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Contents Introduction ...............................................................37 This guide ...............................................................38 Safety icons ............................................................39 Other icons used...............................................40 Other documentation ..............................................40 Service options .......................................................41 Chapter 1: Getting Started...................................
Contents 29 Using the computer for the first time ......................53 Opening the display panel .................................53 Your computer’s features and specifications ....54 Turning on the power........................................54 Adding memory ......................................................55 Installing a memory module .............................56 Removing a memory module............................60 Checking total memory .....................................
Contents Chapter 2: Learning the Basics...................................77 Computing tips .......................................................77 Using the keyboard .................................................78 Character keys .................................................79 Making your keyboard emulate a full-size keyboard .....................................................79 Ctrl, Fn, and Alt keys .........................................80 Function keys.................................
Contents 31 Toshiba’s online resources ...................................101 Chapter 3: Mobile Computing .................................. 102 Toshiba’s energy-saver design..............................102 Running the computer on battery power ..............102 Battery Notice .................................................103 Power management ........................................104 Using additional batteries ...............................104 Charging batteries....................................
Contents Caring for CDs and DVDs................................127 Using external display devices ..............................128 Directing the display output when you turn on the computer ................................128 Adjusting the quality of the external display....129 Display limitations ..........................................130 Using tablet mode.................................................130 Preparing to use the tablet ..............................131 Using tablet mode...........
Contents 33 Setting up for communications.............................148 Determining the COM port .............................149 Using the Ethernet LAN Port ...........................150 Accessing a LAN .............................................151 Using wireless LAN connectivity .....................151 An overview of using the Internet .........................152 The Internet ....................................................152 The World Wide Web ......................................
Contents The Toshiba Rotation Utility..................................170 Cross Menu Utility ................................................174 TOSHIBA Tablet Access Code Utility .....................176 TOSHIBA Zooming Utility......................................177 TOSHIBA SD Memory Card Format.......................178 TOSHIBA SD Memory Boot Utility.........................179 Chapter 7: Keeping Your Files Safe .......................... 181 Using passwords in the Windows ® operating system ....
Contents 35 The Windows® XP operating system can help you ....................................................197 Resolving a hardware conflict ...............................198 A plan of action ...............................................198 Resolving hardware conflicts on your own .....199 Fixing a problem with Device Manager ...........200 Memory problems ..........................................202 Power and the batteries ..................................203 Keyboard problems....................
Contents Power usage mode ..............................................238 Standby mode.......................................................238 Hibernation mode ................................................239 Display modes ......................................................240 Display brightness ................................................240 Disabling or enabling wireless devices .................241 Disabling or enabling the TouchPad .....................241 Keyboard hot keys ..........
Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go. You will find your operating system, Microsoft® Windows® XP Tablet PC Edition, already installed on your computer. Your operating system offers exciting features, multimedia enjoyment, and easy Internet access.
Introduction This guide NOTE The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba's Web site at pcsupport.toshiba.com.
Introduction Safety icons 39 Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Introduction Other documentation Other icons used Additional icons highlight other helpful or educational information: TECHNICAL NOTE: This icon indicates technical information about the computer. HINT: This icon indicates helpful hints and tips. DEFINITION: This icon indicates the definition of a term used in the text.
Introduction Service options 41 Service options Toshiba offers a full line of optional service programs to complement its limited warranty. Toshiba's standard limited warranty, extended warranty, and service upgrade terms and conditions are available at www.warranty.toshiba.com. To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com.
Chapter 1 Getting Started This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations. Creating a computer-friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.
Getting Started Selecting a place to work 43 To keep your computer in prime operating condition, protect your work area from: ❖ Dust, moisture, and direct sunlight ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters ❖ Extreme heat, cold, or humidity ❖ Liquids and corrosive chem
Getting Started Selecting a place to work Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately: 1. Turn off the computer. 2. Disconnect the AC adapter from the power plug socket and computer. 3. Remove the battery pack.
Getting Started Selecting a place to work 45 Some PC Cards can become hot with prolonged use. Overheating of a PC Card can result in errors or instability in its operation. Before you remove a PC Card, always wait for it to cool. You could get burned removing a hot PC Card. Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer. It could damage the computer or cause system failure. ❖ Never turn off the computer if a drive light indicates a drive is active.
Getting Started Setting up your computer Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. The cooling fan may be located on the bottom of the computer. To prevent possible overheating of the CPU, make sure the air intake on the cooling fan is not blocked. The fan draws in air by creating a vacuum.
Getting Started Setting up your computer 47 telephone line or establish a Local Area Network (LAN) connection. See “Connecting the modem” on page 65. Setting up your software NOTE The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices. The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software. 1 From the welcome screen click Next to enter the Setup Wizard.
Getting Started Registering your computer with Toshiba 6 Follow the remaining screen prompts to complete the setup process. Once you click the final screen, your computer restarts automatically. Registering your computer with Toshiba Product registration is strongly recommended, and allows Toshiba to send the Customer periodic updates, announcements, and special offers applicable to the product. Product registration can be completed during the initial start up process of your computer.
Getting Started Connecting to a power source 49 ❖ Connect a full-size keyboard (see “Connecting an external USB keyboard” on page 63) ❖ Connect an external monitor (see “Using external display devices” on page 128) ❖ Connect a local printer (see “Connecting a printer” on page 63) ❖ Install PC Cards (see “Using PC Cards” on page 135) Connecting to a power source Your computer requires power to operate.
Getting Started Connecting to a power source AC adapter cord AC adapter Power cord/cable Sample power cord/cable and AC adapter To connect AC power to the computer: 1 Connect the power cord/cable to the AC adapter. Sample connecting the power cord/cable to the AC adapter Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. 5.375 x 8.375 ver 2.
Getting Started Connecting to a power source _ + 2 51 Plug the AC adapter cord into the DC-IN on the back of the computer. Sample connecting the AC adapter to the computer 3 Connect the power cord/cable to a live electrical outlet. The AC power light on the system indicator glows green.
Getting Started Charging the main battery ❖ Glows green when the main battery is fully charged ❖ Is unlit when the battery is discharged, the battery is not charging, or the AC adapter is not plugged into the computer or AC outlet ❖ Flashing amber means the main battery charge is low and it is time to recharge the main battery or plug in the AC adapter NOTE If the AC power light flashes amber during charging, either the battery pack is malfunctioning, or it is not receiving correct input from the
Getting Started Using the computer for the first time 53 Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Press the display release button. Opening the display panel 2 Lift the display panel. 3 Adjust the display to a comfortable viewing angle. To avoid damaging the display panel, do not force it beyond the point where it moves easily. Never lift the computer by the display panel.
Getting Started Using the computer for the first time computer is operated on battery power, the screen will dim and you may not be able to increase the brightness of the screen while on battery power. To learn how to rotate the display panel or use your computer in tablet mode, see “Using your computer in tablet mode” on page 72.
Getting Started Adding memory 55 2 Check to ensure that all drives are empty. 3 Slide the power lock button down, and then slide the power button to the right and hold it until the on/off light on the system indicator panel glows green—about one second. The preinstalled operating system will load automatically. When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.
Getting Started Adding memory Installing a memory module Your computer is equipped with two memory slots which can provide for various memory configurations. Additional memory modules can be installed in the memory expansion slots on the base of the computer. You will need a standard Phillips No.1 screwdriver for this procedure. If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it.
Getting Started Adding memory 57 3 Unplug and remove any cables connected to the computer, including the AC adapter. 4 Remove the battery. For information on removing the battery, see “Removing the battery from the computer” on page 115. 5 Close the display panel and turn the computer upside down to locate the memory module slot cover. Memory module slot cover Sample locating the memory module slot cover 6 Using a standard Phillips No.
Getting Started Adding memory 8 Place the screw and the cover in a safe place so that you can retrieve them later. Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its pin connector on the side you insert into the computer. 9 Remove the new memory module from its antistatic packaging.
Getting Started Adding memory 59 11 Hold the memory module by its edges so that the gold connector bar faces the slot, at a slight angle to the socket. clip clip Sample inserting the memory module into the socket 12 Check that the module is inserted completely into the socket and lined up squarely with the socket clips. Sample aligning the module into the socket 13 Gently press down on the memory module connector until the clips snap into place.
Getting Started Adding memory Do not force the memory module into position. The memory module should be completely inserted into the socket and level when secured in place. The clips on either side of the memory module snap into place when the memory module is properly inserted. 14 Replace the memory module slot cover and tighten the screw. 15 Re-insert the battery. For more information on inserting the battery, see “Changing the main battery” on page 115. 16 Turn the computer right side up.
Getting Started Adding memory 61 Do not try to remove a memory module with the computer turned on. You can damage the computer and the device. Do not remove the memory module while the computer is in Standby or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved.
Getting Started Connecting an external USB mouse 5 Turn the computer over and restart it. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory module, you can check that the computer has recognized the change. To do this: 1 Click Start, Control Panel, Performance and Maintenance, and then System. 2 The General tab view automatically appears and shows total memory.
Getting Started Connecting an external USB keyboard 63 Connecting a USB mouse The operating system automatically detects the mouse. The mouse and TouchPad can be used at the same time. Connecting an external USB keyboard You can attach an external standard keyboard to a USB port on your computer, provided the keyboard is USB-compatible. Connecting a printer NOTE Your printer documentation may require you to install the printer software before physically connecting the printer to your computer.
Getting Started Connecting a printer To make the connection, you need a suitable USB cable, which may come with your printer. If a USB cable was not included with your printer, you can purchase one from a computer or electronics store. If your printer supports Plug and Play, your computer will automatically recognize the printer; the printer is then ready for use. Refer to your printer documentation for further instructions.
Getting Started Connecting the modem 2 65 Click Add a printer. The Add Printer Wizard appears. Sample Add Printer Wizard 3 Follow the on-screen instructions to set up your printer. Connecting the modem Your computer comes with a built-in modem that can be connected to a standard voice-grade telephone line. The modem allows you to: ❖ Access the Internet. ❖ Communicate with your office’s local area network (LAN), or a larger corporate wide area network (WAN).
Getting Started Connecting the modem Connecting to a phone line Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem provides an RJ11 jack. 1 Plug one end of a telephone cable (purchased separately) into the modem port on the left-side of the computer. Connecting the telephone cable to the modem port 2 Connect the other end to the RJ11 wall jack.
Getting Started Connecting to a network 67 Connecting to a network To learn how to use your computer’s LAN or Wi-Fi® capabilities to connect to a network, see “Accessing a LAN” on page 151 and “Using wireless LAN connectivity” on page 151. Using the TouchPad™ The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger.
Getting Started Using the TouchPad™ cursor is positioned, you can double-tap the TouchPad or click the buttons to open a program or file, or to get information about an icon. The control buttons are adjacent to the TouchPad and are used like the buttons on a mouse. The primary control button is the left one and corresponds to the left mouse button. To doubletap, press the primary button twice in rapid succession. The function of the secondary button depends on the program you are using.
Getting Started Using the TouchPad™ 69 Sample Mouse Properties window 5 Select Disable or Enable, whichever is appropriate. 6 Click Apply. 7 Click OK. The Mouse Properties window closes. 8 Close the Printers and Other Hardware window. 9 Close the Control Panel window. You can also use a hot key to disable or enable the TouchPad. See, “Disabling or enabling the TouchPad” on page 241. 5.375 x 8.375 ver 2.
Getting Started Using the Cross-Functional button Using the Cross-Functional button The Cross-Functional button is located on the front of the display (the left-most button at bottom right). You can use it to move the cursor as well as make selections by pressing it. NOTE While in Primary Landscape mode, you can use FN + Spacebar to change the screen resolution on the fly; from 1450 x 1050 to 1024 x 768 to 800 x 600 (repeated use will recycle the resolutions).
Getting Started Turning off the computer 71 For more information, see “Powering down the computer” on page 90. Closing the display panel When you are finished using the computer, power off and close the display panel to keep dust and dirt out of the computer. If you close the display panel while the computer is still on, one of these actions will occur: ❖ If you have the audible warning set, the computer will beep to notify you that it is still on. See “Toshiba Hardware Setup” on page 169.
Getting Started Using your computer in tablet mode Using your computer in tablet mode One of your computer’s features is a convertible display that allows you to use the screen much as you would a writing tablet. Rotating the screen By simply rotating and folding the screen over the keyboard, your system is ready to use in tablet mode, with the included Toshiba tablet pen.
Getting Started Using your computer in tablet mode 73 Using the computer in tablet mode To remove the tablet pen, press in, and then pull it out from the right side of the computer. For more information on using the computer in tablet mode, see “Using tablet mode” on page 130.
Getting Started Caring for your computer Customizing your computer’s settings There are several ways in which you can customize your computer to suit your particular requirements. Refer to your operating system documentation or Help and Support for details. You may also wish to customize your power usage settings. For more information, see “Power Profiles” on page 113. There are additional custom settings you can choose. See “Toshiba Utilities” on page 159.
Getting Started Caring for your computer 75 Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the drive-in-use light stops glowing) and all external peripheral cables are disconnected. Do not pick up the computer by its display panel or by the back (where the ports are located). Doing so could damage the system. Using a computer lock You may want to secure your computer to a heavy object such as your desk.
Getting Started Caring for your computer The computer is now securely locked. Sample locking the computer 5.375 x 8.375 ver 2.
Chapter 2 Learning the Basics This chapter lists computing tips and provides important information about the system’s basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working. Your computer can be configured to warn you when the battery is running low.
Learning the Basics Using the keyboard ❖ Back up your files to diskettes (or other removable storage media) on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy. ❖ Use Error-Checking and Disk Defragmenter regularly to conserve disk space and help your computer perform at its optimal level.
Learning the Basics Using the keyboard 79 Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase letter l (el) and the numeral 1 are not interchangeable. ❖ The uppercase letter O and the numeral 0 are not interchangeable. ❖ The Caps Lock key changes only the alphabet keys to upper case—the number and symbol keys are not affected.
Learning the Basics Using the keyboard ❖ Press Fn and Ctrl simultaneously to simulate the Ctrl key on the right side of the enhanced keyboard. ❖ Press Fn and Enter simultaneously to simulate the Enter key on the numeric pad of the enhanced keyboard. Ctrl, Fn, and Alt keys Ctrl Alt Fn Ctrl, Fn, and Alt keys The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation.
Learning the Basics Using the keyboard 81 Windows® special keys Start key Application key ® Windows special keys Your computer’s keyboard has two keys, located at the topright of the keyboard, that have special functions in the operating system: ❖ Start key—Opens the Start menu ❖ Application key—Has the same function as the secondary mouse (or TouchPad) button Overlay keys The keys with numbers and symbols on the front of them form the numeric and cursor overlay.
Learning the Basics Using the keyboard Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys. To turn the numeric overlay on, press Fn and F11 simultaneously. The numeric mode light glows when the numeric overlay is on.
Learning the Basics Starting a program 83 To Procedure Type uppercase letters Press Fn and Shift simultaneously while you type the letters Use the numeric keys Press and hold down Shift while you use the overlay keys, then release Shift to return to the cursor control overlay To turn off the cursor control overlay, hold down the Fn key and press F10 again. The cursor control mode light on the keyboard indicator panel goes out.
Learning the Basics Saving your work Saving your work Before you turn off the computer, save your work to the hard disk drive or a diskette. Always save your data even when you are using Standby mode. If your main battery fully discharges, your information will be lost. Your computer can be configured to warn you when the battery is running low, see “Setting battery alarms” on page 111. Many programs offer a feature that saves documents at regular intervals.
Learning the Basics Saving your work 85 2 Choose the drive and folder where you want your file to be stored. 3 Type a file name, then click Save. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. File names The Windows XP operating system supports long file names which can contain up to 255 characters and can include spaces.
Learning the Basics Printing your work Printing your work Verify that the Windows® XP Tablet PC Edition operating system is set up for your printer as described in “Setting up a printer” on page 64. TECHNICAL NOTE: You only need to set up the printer the first time you connect it. If you use more than one printer or are changing printers, you will need to set up the operating system to run with the additional printer(s). To print a file: 1 If your printer is not on, turn it on now.
Learning the Basics Backing up your work 87 Backing up your work Backing up your files means copying individual files to media, such as a writable CD. Or, you can copy entire sections of your hard disk to another device such as a tape drive or to your network partition. To back up to a writable CD, optional diskette drive, or other media: 1 Attach an optional external drive to one of the USB ports. 2 Insert the media into the appropriate drive. 3 Click Start, then click My Computer.
Learning the Basics Playing audio online Help or your operating system documentation for information on restoring files. Playing audio Insert an audio CD into the optional external DVD-ROM/ multi-function drive and close the disc tray. The computer automatically detects a disc in the drive and opens the Audio CD window. To play an audio CD, select Play Audio CD using Windows Media Player and click OK.
Learning the Basics Playing audio 89 Sample Windows Media Player screen The Windows® Media Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel. ❖ To stop the CD, click the Stop button. Before putting on headphones to listen to an audio CD, turn the volume dial down, and do not set the volume too high when using the headphones. Continuous exposure to loud sound can harm your hearing. 5.375 x 8.
Learning the Basics Powering down the computer Powering down the computer When you power down the computer, you have a number of options to choose from: ❖ Turn Off or Shut down, which power off the computer ❖ Hibernation, which saves the current operating state to the hard disk and powers off the computer ❖ Standby, which saves the current operating state to memory and enters a low power mode ❖ Restart, which restarts the computer Each option has its advantages.
Learning the Basics Powering down the computer ❖ 91 When starting up again, the system does not automatically open the programs and files you were previously using. Restart command Restart is the same as Turn Off or Shut down but automatically powers up the computer. Use it when you need to reload the operating system, for example to activate changes to system settings.
Learning the Basics Using Turn Off or Shut down Standby command The Standby command puts the computer into a powersaving mode. Standby stores the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Factors to consider when choosing Standby: ❖ While in Standby mode, the computer uses some battery power. If your computer is left in Standby mode for an extended period, your computer could lose data.
Learning the Basics Using Turn Off or Shut down 93 Sample Turn off computer window 2 Click Turn Off. The computer turns itself off. If you are connected to a Windows® network server (domain server), power off the computer as follows: 1 Click Start, Shut down. The Shut Down window appears. 2 Select Shut down from the drop-down list. 3 Click OK. The computer shuts down completely.
Learning the Basics Using Turn Off or Shut down Sample TOSHIBA Power Saver Properties window 4 Click the Setup Action tab. Sample Setup Action window 5 Select Shut down for the option you want. ❖ When I press the power button 5.375 x 8.375 ver 2.
Learning the Basics Using Hibernation 95 Set this option to Shut down if you want the computer to turn off when you slide the power button. 6 Click Apply. 7 Click OK to close the TOSHIBA Power Saver Properties window, then close the Control Panel. Starting again after Turn Off or Shut down To start the computer up again, slide and release the power button; the on/off light changes to green. Using Hibernation Enabling the Hibernation command Hibernation is a default setting.
Learning the Basics Using Hibernation Sample Turn off computer window with Shift key held down to show Hibernate option 2 Hold down the shift key and click Hibernate (“Hibernate” only appears when the Shift key is pressed). The computer saves the state of the system, including all open programs and files, to the hard disk, and then powers down completely.
Learning the Basics Using Hibernation 97 To set up your Hibernation options: 1 Click Start, Control Panel. The Control Panel window appears. 2 Click Performance and Maintenance. 3 Double-click the Toshiba Power Saver icon. The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window 4 Click to select a profile. 5 Click the Setup Action tab. 6 Select Hibernation for the options you want.
Learning the Basics Using Standby Set this option to Hibernation so that the computer will go into Hibernation mode when you close the display panel. 7 Click Apply. 8 Click OK to close the TOSHIBA Power Saver Properties window, then close the Control Panel. Starting again from Hibernation To start up the computer from Hibernation mode, slide and release the power button until the on/off icon glows green. The computer returns to the screen you were using.
Learning the Basics Using Standby 99 mode. The on/off light ( ) blinks amber indicating the machine is in Standby mode. If you are connected to a Windows® network server (domain server), power down the computer using the Standby command as follows: 1 Click Start, Shut down. The Shut Down window appears. 2 Select Stand By from the drop-down list of options. 3 Click OK. The computer saves the state of all open programs and files to memory, turns off the display, and goes into a low-power mode.
3 Learning the Basics Using Standby Double-click the Toshiba Power Saver icon. The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window 4 Click to select a profile. 5 Click the Setup Action tab. Sample Full Power Properties window 5.375 x 8.375 ver 2.
Learning the Basics Toshiba’s online resources 6 101 Select Standby for the options you want. ❖ When I press the power button Set this option to Standby so that the computer will go into Standby mode when you press the power button. ❖ When I close the lid Set this option to Standby so that the computer will go into Standby mode when you close the display panel. 7 Click Apply. 8 Click OK to close the TOSHIBA Power Saver Properties window, then close the Control Panel.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been set by Toshiba.
Mobile Computing Running the computer on battery power 103 Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication.
Mobile Computing Running the computer on battery power The RTC battery powers the RTC memory that stores your system configuration settings and the current time and date information. It maintains this information for up to a month while the computer is turned off. TECHNICAL NOTE: The RTC battery does not charge while the computer is turned off, even when AC power is attached. The RTC battery charges when the computer is powered on.
Mobile Computing Charging batteries 105 Charging batteries NOTE Battery charge time may vary depending on the applications, power management settings, and features used. The battery needs to be charged before you can use it to power the computer. Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your notebook computer.
Mobile Computing Charging batteries The battery may not start charging immediately under the following conditions: ❖ The battery is extremely hot or cold. To ensure that the battery charges to its full capacity, wait until it reaches room temperature (50 to 80 degrees Fahrenheit, 10 to 26 degrees Celsius). ❖ The battery is almost completely discharged. Leave the power connected and the battery should begin charging after a few minutes.
Mobile Computing Monitoring main battery power NOTE 107 The above error message may vary by computer model. The RTC battery does not charge while the computer is turned off even when the AC adapter is charging the computer. The RTC battery charges when the computer is powered on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working.
Mobile Computing Monitoring main battery power ❖ Is unlit when the battery has discharged, the battery is not charging, or the AC adapter is not plugged into the computer or AC outlet. NOTE Battery life and charge time may vary, depending upon power management settings, applications and features used. ❖ Flashes amber when the main battery charge is low and it is time to recharge the main battery or plug in the AC adapter.
Mobile Computing Monitoring main battery power 109 Battery light On/off light Sample power and battery light locations Determining remaining battery power You can monitor the main battery’s remaining charge. The computer calculates the remaining battery charge as it operates, based on your current rate of power use. To show remaining power: 1 Click Start, Control Panel, Performance and Maintenance, and then Toshiba Power Saver. 5.375 x 8.375 ver 2.3.
Mobile Computing Monitoring main battery power The Toshiba Power Saver Properties dialog box appears. Sample Toshiba Power Saver Properties dialog box The remaining battery charge is indicated on the top-left side of the dialog box. With repeated discharges and recharges, the battery’s capacity gradually decreases. A frequently used older battery does not power the computer for as long as a new battery, even when both are fully charged.
Mobile Computing Monitoring main battery power 111 The Windows® operating system has additional power management options that can be accessed through an icon in the Control Panel. For more information, see “Power Management” on page 167.
Mobile Computing Monitoring main battery power 1 Click Start, Control Panel, Performance and Maintenance, and then Toshiba Power Saver. 2 Click the Setup Action tab. 3 Configure the Alarm settings to suit your needs.
Mobile Computing Monitoring main battery power 113 Power Profiles You can choose a predefined Power Profile or select your own combination of power management options. To do this: 1 Click Start, Control Panel, Performance and Maintenance, and then Toshiba Power Saver. The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window 2 Select an appropriate profile for your work environment or create your own custom profile.
Mobile Computing Monitoring main battery power For more information, see “Power Management” on page 167. Using a hot key to set the Power Profile You may use a hot key to set the Power Profile. To set the Power Profile: 1 Press Fn and F2 simultaneously to display the Power Profile pop-up window. Sample Power Profile mode pop-up window 2 While continuing to press Fn, press F2 until you select the desired Power Profile.
Mobile Computing Changing the main battery 115 Changing the main battery Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or fire, and could also damage the battery pack. Never expose a battery pack to abnormal shock, vibration or pressure.
5 Mobile Computing Changing the main battery Slide the battery lock to the left. Unlocking the battery 6 Push the release latch up. Releasing the battery 5.375 x 8.375 ver 2.3.
Mobile Computing Changing the main battery 7 117 Insert a fingertip in the battery pack recessed area. Pulling up the battery 8 Pull the discharged battery module out of the computer. Sample removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately. Always dispose of used battery packs in compliance with all applicable laws and regulations.
Mobile Computing Changing the main battery Inserting a charged battery 1 Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot. The battery has been designed so that you cannot install it with reverse polarity. If the battery does not slide into the slot easily, remove the battery and try again. Avoid forcing the battery into position.
Mobile Computing Taking care of your battery 119 Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life. Safety precautions ❖ If the battery pack produces an odor, overheats or changes color or shape while it is being used or charged, turn off the computer’s power immediately and disconnect the power cord/cable from the power socket. Carefully remove the battery pack from the computer. ❖ Do not try to disassemble a battery pack.
❖ Mobile Computing Taking care of your battery Do not expose the battery pack to fire. The battery pack could explode. Maximizing battery life To maximize the life of your battery pack: ❖ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: 1 Turn off the computer’s power. 2 Disconnect the AC adapter and turn on the computer’s power. If it does not turn on, go to step 4.
Mobile Computing Disposing of used batteries 121 ❖ If you are not going to use the computer for more than eight hours, disconnect the AC adapter. ❖ Store spare battery packs in a cool dry place out of direct sunlight. Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you have fully recharged the battery. You must discard a battery if it becomes damaged.
Mobile Computing Traveling tips Please be kind to our shared environment. Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly. If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. Traveling tips The environmental precautions listed in “Selecting a place to work” on page 42, also apply while traveling.
Chapter 4 Expansion Options Your computer is designed to work in your office as well as on the road. This chapter explains how to set up several optional external devices so that your notebook can provide all the convenience of a traditional desktop computer. To order additional devices and accessories, see the accessories information provided with your computer, or visit accessories.toshiba.com.
Expansion Options Using an optional external DVD-ROM drive Using an optional external DVD-ROM drive An optional external DVD drive allows you to use CDs and DVDs and is useful for installing software on the hard disk, and exchanging information with other systems. Optional external DVD-ROM drive Connecting an optional external DVD drive You may want to use an external USB DVD drive instead of an external SCSI DVD drive. You can attach an external USB DVD drive to one of the computer’s USB ports.
Expansion Options Using an optional external DVD-ROM drive 125 Your computer may come with an external DVD/CD-RW drive that can read CDs and DVDs. To attach this drive to your computer using an optional PC Card SCSI adapter, follow the instructions in “Using PC Cards” on page 135. Inserting discs (CD or DVD) To insert a disc into the drive: 1 Make sure the computer is turned on. 2 Make sure the drive-in-use indicator light is off. 3 Press the drive’s eject button.
Expansion Options Using an optional external DVD-ROM drive 6 Place the disc carefully in the disc tray, label side up. 7 Gently press the disc onto the center spindle until you feel it click into place. Handle DVDs and CDs carefully, making contact only with the center hole and edge. Never touch the surface of the disc. Never stack discs. If you incorrectly handle the discs, you could lose data. 8 Make sure the disc is completely on the spindle and is lying flat on the tray.
Expansion Options Using an optional external DVD-ROM drive 127 To remove a disc with the computer turned off: 1 Insert a slender object, such as a straightened paper clip, into the manual eject hole. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Gently pull the tray out until it is fully open, remove the disc, and place it in its protective cover. 3 Gently push the tray in to close it.
Expansion Options Using external display devices Using external display devices Your computer comes with a built-in LCD display, but you can easily attach an external monitor to your computer if you need a larger screen. To do this: 1 Connect the monitor’s video cable to the RGB (monitor) port on the back of the computer. 2 Connect the monitor’s power cord/cable to a live electrical outlet. 3 Turn on the external monitor.
Expansion Options Using external display devices 3 129 Release the Fn key. TECHNICAL NOTE: You can also change these settings using the Display Properties Box. Using the Cross-Functional button The Cross-Functional button, located on the front of the display (the left-most button at bottom right), can be used to select the external display device. Press and hold the CrossFunctional button for two seconds until the external display screen displays.
Expansion Options Using tablet mode Display limitations Keep in mind that the quality of the display will be limited to the capabilities of the external video device. ❖ If the external video device, such as an SVGA monitor, is capable of displaying at a maximum resolution of 800 x 600 and your system is set for a higher resolution, only part of the desktop will appear on the screen. You can view the “lost” area by scrolling to it.
Expansion Options Using tablet mode 131 Preparing to use the tablet 1 Press the display panel release button and lift the display panel. 2 Slide the power button to the right and hold it until the on/off light on the system indicator panel glows green— about one second. 3 Rotate the display panel clockwise 180o (degrees). When you complete this task, the screen faces away from the keyboard.
Expansion Options Using tablet mode The display latch will click and lock the screen in tablet position. Display latch Folding the display panel down flat By default, the computer desktop will automatically rotate to primary portrait view. For more information on changing tablet screen settings, see “The Toshiba Rotation Utility” on page 170. 6 NOTE To send the video to an external monitor, use the Cross Menu button (the Cross-Functional button) and select the display option.
Expansion Options Using tablet mode 133 Removing the Toshiba tablet pen from the slot on the tablet NOTE 2 Your computer may have come equipped with an optional emergency pen to be used in case the primary pen is unavailable. To access the location of the optional emergency pen, you must remove the battery following the procedures described in “Changing the main battery” on page 115. Once the battery is removed, locate the optional emergency pen inside the battery compartment.
Expansion Options Using tablet mode To learn how to manually change the layout of the screen from portrait to landscape, see “The Toshiba Rotation Utility” on page 170. NOTE Included with your computer is Sensiva’s Symbol Commander™ allowing you to quickly execute commands (for example, changing the layout of the screen from landscape to portrait) by drawing a pre-assigned symbol on the screen. For details on using Symbol Commander, refer to the online help with the application.
Expansion Options Using the i.LINK® port 135 Returning the computer to its original configuration When you are finished using the tablet, follow the steps below to return the computer to its original configuration: 1 Return the Toshiba tablet pen to its slot on the right side of the computer. 2 Press the display latch release button. 3 Lift the display panel to its upright position. 4 Rotate the display panel counter-clockwise 180o.
Expansion Options Using PC Cards Most PC Cards conform to the PCMCIA (Personal Computer Memory Card International Association) standard. TECHNICAL NOTE: For PCMCIA-compatible PC Cards, check the package to make sure they conform to the PCMCIA 2.1 standard (or later). Other cards may work with your computer, but they are likely to be much more difficult to set up and use.
Expansion Options Using PC Cards 3 137 When the card is almost all the way into the slot, push firmly, but gently, to ensure a firm connection with the computer. Avoid forcing the card into position. Removing a PC Card 1 Locate the PC Card eject tab. 2 Push the eject button. The eject button pops out from the slot. 3 Push the eject button again so the card will pop out. 4 Grasp the edges of the PC Card and slide it out of the slot.
❖ Expansion Options Using an optional SD™ card Never remove a SCSI card while any of the SCSI devices connected to it are operating. DEFINITION: SCSI is an acronym for Small Computer Systems Interface. A single SCSI PC Card enables you to connect several SCSI devices to your computer at the same time. Before removing a PC Card, stop it by clicking the PC Card (PCMCIA) icon on the taskbar. Using an optional SD™ card Your computer supports the use of an SD card.
Expansion Options Using an optional SD™ card 139 Installing the SD™card in the SD slot To insert an SD card, turn the card so that the connector (metal area) faces down then push the card in the slot until it locks in place. If the operating system does not recognize an inserted SD card, remove and insert it again. The green light on the right side of the SD card slot will glow when the card is being accessed. If the SD card is not inserted into the slot correctly, any data saved to the card may be lost.
Expansion Options Using an optional SD™ card system may not shut down properly. If this occurs, reset your computer by sliding the power button to the right and holding it for four seconds. Removing an optional SD™ card Before removing an SD card from the SD slot, close any applications which utilize the SD card. Use the eject utility to ensure that the card is ready to be removed. Once the activity indicator light has turned off, you may safely remove the card.
Chapter 5 Exploring Your Computer’s Features In this chapter, you will explore other features of your notebook computer.
Exploring Your Computer’s Features Personalizing your desktop Personalizing your desktop Your desktop is your virtual workspace. This section explains how to customize its features for the way you like to work.
Exploring Your Computer’s Features Personalizing your desktop 143 Bringing the world to your desktop With the Windows® Professional Tablet Edition operating system you can set up your desktop with complete World Wide Web integration at a single click. Turning on the Web content interface The first step to bring active content to your desktop is to turn on the Web content interface: 1 Point to an empty space on the desktop and click the secondary button. 2 Click Properties.
7 Exploring Your Computer’s Features Personalizing your desktop To browse the Gallery for more components to add, click Visit Gallery. In order to browse, an active Internet connection must be established. 8 To select some other Web site, type the address of the Web site you want or click Browse to locate it. You can configure the Web content interface in several other ways. For further information, see your operating system documentation or access Windows® Help by clicking Start, Help and Support.
Exploring Your Computer’s Features Personalizing your desktop 145 The My Computer window appears. 2 Select the Tools menu, then click Folder Options. The Folder Options dialog box appears. Sample Folder Options dialog box 3 Click the preferred options. 4 Click Apply, then OK. Personalizing individual windows Just as you can display a Web page on your desktop, you can also display a Web page in an individual window. If you subscribe to the Web page, it can be automatically updated on a regular basis.
Exploring Your Computer’s Features Personalizing your desktop Customizing window toolbars You can display one or more customizable toolbars at the top of a window. As you browse, the operating system detects the kind of information presented in the window and automatically displays the appropriate toolbar buttons and menus. You can also add these toolbars to the taskbar. Address bar Standard buttons Sample toolbar locations 5.375 x 8.375 ver 2.
Exploring Your Computer’s Features Personalizing your desktop 147 The elements you can add to the top of the window are: Toolbar element Description Address Bar Opens Web pages, programs, folders, or documents. By default, the address bar shows your current location, and whether it is a folder or a Web page. You can browse to another location by typing an address — a URL, a path, or even a program name.
Exploring Your Computer’s Features Setting up for communications 2 Open the folder you want to view as a Web page. 3 In the Tools menu, select Folder Options. 4 In the Tasks section, click the button for Show common tasks in folders. 5 Click Apply, then OK. Sample Control Panel window as a Web page The addition of the name of the folder and instructions for how to use the folder on the left give the window the appearance of a Web page.
Exploring Your Computer’s Features Setting up for communications ❖ NOTE 149 An Internet Service Provider (ISP) or online service if you plan to use the Internet There are many other ways to connect to the Internet in addition to those discussed in this section. For troubleshooting information related to this topic, see “Modem problems” on page 217 and “Wireless networking problems” on page 218. Determining the COM port Your modem is connected to one of the computer’s COM (communications) ports.
5 Exploring Your Computer’s Features Setting up for communications To verify that the modem is set up properly, double-click the COM port to which your modem is connected. The Toshiba Software Modem Properties box appears. In the device status area, the computer should indicate whether the modem is working properly. 6 If the modem is not working properly, click Troubleshooting and follow the instructions. 7 Click OK to close the Properties box, then the Phone and Modem options box.
Exploring Your Computer’s Features Setting up for communications 151 Accessing a LAN To access a LAN: ❖ At the office, you can connect the network Ethernet cable to the RJ45 jack on your computer. ❖ Your computer may be equipped for wireless communications. If so, see “Using wireless LAN connectivity” on page 151. ❖ From home or while on the road you will need a dial-up connection. Ask your network administrator for the telephone number to access the network.
Exploring Your Computer’s Features An overview of using the Internet An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Internet Service Providers ❖ Connecting to the Internet ❖ Surfing the Internet ❖ Internet features ❖ Uploading to, and downloading files from, the Internet The Internet The Internet is an association of thousands of networks and
Exploring Your Computer’s Features An overview of using the Internet 153 Internet Service Providers To connect a computer directly to the Internet, many people and businesses use an Internet Service Provider (ISP). An ISP is a company that has the equipment and the telecommunication lines necessary to maintain an Internet connection.
Exploring Your Computer’s Features An overview of using the Internet Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type in the Web address. The Web address, or Uniform Resource Locator (URL), is a unique identifier for that computer system linked to the Internet. Web addresses can also appear within a Web page’s text, and are known as links.
Exploring Your Computer’s Features Using audio features 155 clearinghouse where all the messages are placed, like a gigantic bulletin board. ❖ Online shopping Many Web sites offer products and services for sale. Uploading to, and downloading files from, the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer to a site on the Web), or downloading (transferring data from a site on the Web to your computer).
Exploring Your Computer’s Features Using audio features TECHNICAL NOTE: Use amplified speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer. To play back sound files through headphones or external speakers: 1 Locate the headphone jack on the computer. 2 Using any necessary adapters, plug the cable from the headphones or external speakers into the headphone jack. The headphone jack requires a 16-ohm stereo mini jack.
Exploring Your Computer’s Features Using audio features 157 You may also record sounds as .WAV files by connecting an external microphone or other sound source to the microphone jack. Using a microphone 1 Connect an external microphone to the computer. 2 Click Start, All Programs, Accessories, Entertainment, then click Sound Recorder. Positioning bar Record Stop Play Skip forward Skip backward Sample Sound Recorder screen 3 NOTE Click the Record button and speak normally into the microphone.
6 NOTE Exploring Your Computer’s Features Using audio features To save the file, select Save from the File menu. The microphone on your computer might be set to Mute. To check this, click Start, point to All Programs, Accessories, Entertainment, and then click Volume Control. Adjusting recording settings The better the quality of the recording, the more disk space the sound file requires. Experiment to find a balance that fits your needs.
Chapter 6 Toshiba Utilities Your computer includes several utilities designed to help you to reconfigure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options.
Toshiba Utilities Fn-esse Fn-esse The operating system shortcuts and Toshiba’s Fn-esse program provide quick ways to open programs, documents, and folders from within any program without using the Start menu. This section describes how to use the Fn-esse program to quickly access your programs and files.
Toshiba Utilities Fn-esse 161 Sample Fn-esse keyboard The keys are color-coded as follows: ❖ Available keys are white. ❖ Assigned keys and keys associated with a popup list are shown on the Fn-esse keyboard in the selected color. ❖ Unavailable keys are not shown. Assigning a key to a program or document There are two ways to assign a key to open a program or document: ❖ Drag-and-drop ❖ Use the keyboard or pointing device The method most often used is drag-and-drop.
Toshiba Utilities Fn-esse 4 Click and hold the primary button as you drag the highlighted item from Explorer to the key on the Fn-esse keyboard you want to assign to it. 5 Release the primary button. Fn-esse displays the Add/Edit Command dialog box with the Description, Command Line, and Working Directory fields automatically completed. 6 Click OK to close the Add/Edit Command dialog box with your key assignment in place. The program or document is now associated with the key you just selected.
Toshiba Utilities Fn-esse 4 163 ❖ Enter the Description, Command Line, and Working Directory for the new Fn-esse key assignment, or click the Browse button to specify this information. ❖ Click OK. To make a popup assignment, select Popup to display the Application Explorer dialog box, then complete these steps: ❖ Select the desired folder. The left side of the Application Explorer window displays the folders in the Programs menu. The right side lists the programs and documents in the folder.
Toshiba Utilities Hotkey utility Changing or removing existing key assignments 1 In the Fn-esse keyboard, click the key you wish to change with the secondary button. Fn-esse displays the Assignment Type dialog box. 2 To change the key assignment, click Direct or Popup and continue as if you were creating a new assignment. 3 To remove the key assignment, click Clear.
Toshiba Utilities TOSHIBA Console 165 TOSHIBA Console The TOSHIBA Console provides quick access to computer functions and allows you to customize a range of computer settings. To access this utility: 1 Click Start, All Programs, Toshiba, Utilities, then click Console. The TOSHIBA Console window appears. Sample TOSHIBA Console window The TOSHIBA Console offers three categories of options: ❖ Customize Your Computer ❖ Network ❖ Security 5.375 x 8.375 ver 2.
Toshiba Utilities TOSHIBA Console Customize Your Computer The options available in this category are: ❖ Power Management ❖ Mouse ❖ Hotkey assignment using Fn-esse ❖ Toshiba Hardware Setup ❖ Tablet and Pen Settings ❖ Toshiba Mobile Extensions ❖ ConfigFree Network The options available in this category are: ❖ IR Utility ❖ Bluetooth® settings ❖ Start Bluetooth ❖ Bluetooth Local COM Settings ❖ Connectivity Doctor Security The options available in this category are: ❖ Supervisor pa
Toshiba Utilities Power Management 167 Power Management NOTE Toshiba recommends that you use the Toshiba Power Management Utility for changing system power settings. The Power Management feature enables you to control your computer’s power usage, regardless of the source, and use the many preset power modes, or create one yourself. To access Power Management through the TOSHIBA Console, click the Power Management icon. The TOSHIBA Power Saver Properties window appears.
Toshiba Utilities Power Management You can either use one of the preset profiles or create and use your own customized mode. The preset profiles cannot be deleted. By changing the options that appear in the Toshiba Power Saver Properties window and clicking OK, you can reconfigure that function. Any options that you change become effective when you click either OK or Apply.
Toshiba Utilities Power Management 169 Customizing a power mode 1 Highlight the profile on the Profiles window. 2 Make the desired changes to settings on the Basic Setup page and the Setup Action page. 3 Click Apply. 4 Click OK. Toshiba Hardware Setup Toshiba Hardware Setup is the Toshiba configuration management tool. To access it: In the TOSHIBA Console, click the Toshiba Hardware Settings icon.
Toshiba Utilities The Toshiba Rotation Utility You can also manually choose the boot-up sequence by pressing the power button, then quickly pressing the right or left arrow keys. Select the boot device by pressing the right or left arrow keys, then pressing the Enter key. NOTE Since the system is a quick-booting system, you must press the arrow keys immediately after pressing the power button. ❖ Keyboard—Allows you to enable or disable Wake up from the keyboard.
Toshiba Utilities The Toshiba Rotation Utility ❖ 171 Secondary landscape To change the display format: 1 Click Start, All Programs, Toshiba, Tablet PC, and then click Rotation Utility. The Toshiba Rotation Utility screen appears: Sample Toshiba Rotation Utility screen 2 Select a new display format for either PC mode or Tablet PC mode. 5.375 x 8.375 ver 2.
3 Toshiba Utilities The Toshiba Rotation Utility Click OK. NOTE Toshiba recommends that you use the Toshiba Rotation Utility to change screen rotation options and settings for the tablet feature Tablet and Pen Settings. NOTE The Escape key, located between the Cross-Functional button and the Windows Security button on the front of the display can “lock” the display in its current display setting - landscape or portrait.
Toshiba Utilities The Toshiba Rotation Utility 173 ❖ The Settings tab allows you to specify whether you are left handed or right handed, and the menu location. ❖ While the Display tab can be used to change the screen’s orientation and adjust screen brightness, it is recommended that you use the Toshiba Rotation Utility (see page 170) to change the screen’s orientation, and the Toshiba Power Saver Utility (click its icon in the System Tray) to adjust screen brightness.
Toshiba Utilities Cross Menu Utility Cross Menu Utility The Cross Menu Utility allows you to make Hot Key assignments to launch applications, access Toshiba utilities, or create your own custom menus. To start the Cross Menu Utility: 1 Press and hold the Cross-Functional button for two seconds until the following screen displays. Sample Cross Menu Utility screen 2 Move the Cross-Functional button up or down to select a menu.
Toshiba Utilities Cross Menu Utility 175 Creating a New Menu NOTE You can add up to five menus. To create a new menu: 1 Click Start, All Programs, Toshiba, Tablet PC, and then Cross Menu. The Cross Menu Setting window appears. Sample Cross Menu Setting window 2 Click New. 3 Click Add File. 4 Browse for the application(s) you want to add to the menu and click Open. 5 When you have finished adding applications to the menu, click OK. 5.375 x 8.375 ver 2.
Toshiba Utilities TOSHIBA Tablet Access Code Utility TOSHIBA Tablet Access Code Utility This utility allows you create and register an access code controlling who can log onto Windows. NOTE When creating and registering an access code, you can choose any character or symbol you want. The more unique or complex the code, the more secure. However, be sure to create a code that is easily remembered.
Toshiba Utilities TOSHIBA Zooming Utility 177 TOSHIBA Zooming Utility This utility allows you zoom in and zoom out of applications as well as the icons for Microsoft® Internet Explorer, Microsoft® Office, Windows® Media Player, and Adobe® Reader. To access the utility, click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Zooming Utility. The TOSHIBA Zooming Utility screen appears. Sample TOSHIBA Zooming Utility screen 5.375 x 8.375 ver 2.
Toshiba Utilities TOSHIBA SD Memory Card Format TOSHIBA SD Memory Card Format This utility is used to format SD cards used with the Bridge Media Adapter Slot. To access the SD Memory Card Format utility through the TOSHIBA Assist window, click Optimize on the left side of the window, then double-click the SD Memory Card Format icon. The SD Memory Card Format screen appears. Sample SD Memory Card Format screen To format an SD memory card: 1 Select the drive corresponding to the SD memory card.
Toshiba Utilities TOSHIBA SD Memory Boot Utility 179 TOSHIBA SD Memory Boot Utility In order to boot from an SD card, you must make the SD card bootable. To do so, run the Toshiba SD Memory Boot Utility. 1 Attach a USB floppy drive to your computer, and insert a bootable floppy disk. 2 Insert the SD card into the SD card slot. NOTE 3 Be sure to back up your data before performing this procedure as data on the drive may be lost.
5 NOTE 6 Toshiba Utilities TOSHIBA SD Memory Boot Utility Select Read from a floppy disk. To create a bootable SD card with the “Read from an image file” option requires a third-party application. Click Start. 5.375 x 8.375 ver 2.
Chapter 7 Keeping Your Files Safe You may have files on your computer that you want to keep private. Your computer comes with several options that can help you keep your computer and files safe from unwanted intrusion. This chapter describes the security options for your notebook computer. Using passwords in the Windows® operating system Setting password lets you leave your computer, secure in the knowledge that nobody can access your files.
❖ Keeping Your Files Safe Using passwords in the Windows® operating system A HDD password— A hard disk drive password that protects your data by requiring a password when you try to access the hard disk, whether it is in your computer or in another system. You can set a hard disk drive user password and/or a hard disk drive master password. If you choose to set a hard disk drive user password, we strongly recommend that you set a hard disk drive master password as well.
Keeping Your Files Safe Using passwords in the Windows® operating system 2 Open the User Password tab. 3 Click Set. 183 A Set User Password dialog box appears. 4 Type in the password. 5 Reenter the password and click Set. A message box appears asking if you want to save the password on removable media. 6 If you want to save the password, click OK and then follow the on-screen instructions. If you do not want to save the password, click Cancel. 7 Click OK on the Toshiba Password Utility window.
Keeping Your Files Safe Using passwords in the Windows® operating system Using the power-on (user-level) password Whenever you start your computer with a power-on (userlevel) password in effect, the computer prompts you to enter the password before it goes through its normal startup procedure. When your computer prompts you to enter your password, type it in and press Enter. If you enter the password correctly, the computer continues with its normal startup procedure.
Keeping Your Files Safe Using passwords in the Windows® operating system 185 ❖ Setting a hard disk drive user password prevents an unauthorized user from accessing your hard disk, even if it is removed and installed on another computer. This password does not encrypt data on the hard disk. ❖ Setting a hard disk drive master password lets you bypass the hard disk drive user password and access your hard disk, in case you forget the hard disk drive user password.
2 Keeping Your Files Safe Using passwords in the Windows® operating system Hold down the Esc key and press and hold the power button until the on/off light on the system indicator panel illuminates (green) for approximately one second. When the following message appears on the screen: “Check system, Then press [F1] key,” press F1. The System Setup screen appears. 3 Press H to move to the HDD PASSWORD section on the screen. 4 Press the spacebar to select User Only password mode.
Keeping Your Files Safe Using passwords in the Windows® operating system 187 illuminates (green) for approximately one second. When the following message appears on the screen: “Check system, Then press [F1] key,” press F1. The System Setup screen appears. 3 Press H to move to the HDD PASSWORD section on the screen. 4 Press the spacebar, then type in your user password and press Enter. 5 If you want to change the password, input the new password.
Keeping Your Files Safe Using passwords in the Windows® operating system To register master and user passwords in System Setup: 1 Click Start, then click Shutdown, and click OK. The computer shuts down. 2 Hold down the Esc key and press and hold the power button until the on/off light on the system indicator panel illuminates (green) for approximately one second. When the following message appears on the screen: “Check system, Then press [F1] key,” press F1. The System Setup screen appears.
Keeping Your Files Safe Using passwords in the Windows® operating system 189 Changing the master and user passwords in System Setup To change the master and user passwords in System Setup: 1 Click Start, then click Shutdown, and click OK. The computer shuts down. 2 Hold down the Esc key and press and hold the power button until the on/off light on the system indicator panel illuminates (green) for approximately one second.
Keeping Your Files Safe Using passwords in the Windows® operating system Deleting the hard disk drive master and user passwords in the System Setup HINT: You must delete the hard disk drive master password before you can delete the hard disk drive user password. To delete the master and user passwords in System Setup: 1 Click Start, then click Shutdown, and click OK. The computer shuts down.
Chapter 8 If Something Goes Wrong Some problems you may encounter when using your computer are relatively easy to identify and solve. Others may require help from your network administrator or the manufacturer of a software program. This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
If Something Goes Wrong Problems that are easy to fix The Windows Task Manager window appears. 2 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with the next step. 4 Close the remaining programs one by one by selecting the program name, then End Task.
If Something Goes Wrong Problems when you turn on the computer 193 To record the details: 1 Click the Details button and select the text the operating system displays. The Details button displays information that the software manufacturer needs to help you solve your problem. 2 Press Ctrl and c simultaneously to copy the text to the clipboard. 3 Open Notepad (click Start, All Programs, Accessories and then click Notepad). 4 Press Ctrl and v simultaneously to paste the details into Notepad.
If Something Goes Wrong Problems when you turn on the computer The computer starts but when you press a key nothing happens. Verify that the active program accepts text input. Try clicking your mouse on an area where you can type text, and try typing again. Your computer may be in Standby mode and have a software or resource conflict. When this happens turning the power on returns you to the problem instead of restarting the system. To clear the condition, press Ctrl, Alt, and Del simultaneously.
If Something Goes Wrong The Windows® operating system is not working 195 If you are running on battery power, it is recommended that you do not leave the computer in Standby mode for long periods of time. To charge the battery, leave the computer plugged into a live wall outlet for several hours. For more information see “Charging batteries” on page 105. The computer displays the Non-System disk or disk error message. Make sure there is no diskette in the optional external diskette drive.
If Something Goes Wrong The Windows® operating system is not working Using Startup options to fix problems If the operating system fails to start properly, you may have to change your system’s configuration or verify the startup procedure to fix the problem. To do this, use the options in the Startup menu. To open the Startup menu: 1 Restart your computer. 2 Press F8 when your computer starts and before Windows starts loading.
If Something Goes Wrong The Windows® operating system is not working 197 Internet problems My Internet connection is very slow. Many factors contribute to the speed with which you can surf the Internet. They include: modem speed, telephone line conditions, time of day (when everyone else is surfing, your access can be slow) and popularity of the sites you are trying to access. If accessing a particular site is very slow, try later. My browser cannot find the URL address I typed in.
If Something Goes Wrong Resolving a hardware conflict You can connect to Support Online by clicking Support from the menu or by going to pcsupport.toshiba.com. Resolving a hardware conflict If you receive an error message telling you there is a device driver conflict or a general hardware problem, try using Windows® Help and Support to troubleshoot the problem first. For help on hardware conflicts: 1 Click Start, then click Help and Support. 2 Click the Hardware link in the window’s left pane.
If Something Goes Wrong Resolving a hardware conflict 199 Resolving hardware conflicts on your own Computer components need resources to accomplish a task. A device, such as a disk drive or a modem, needs a channel to the computer’s Central Processing Unit (CPU). It also needs a direct channel to the computer’s memory to store information as it works. These channels of communication are commonly referred to as system resources.
If Something Goes Wrong Resolving a hardware conflict If you install an older (legacy) device that the operating system cannot recognize, the operating system may have difficulty assigning resources to it. As a result, a hardware conflict can occur. Resolving conflicts There are several things you can do to resolve hardware conflicts: ❖ Get the most recent drivers from the manufacturer. ❖ Disable the device. For an older device, remove it from the computer.
If Something Goes Wrong Resolving a hardware conflict 201 Disabling a device 1 Open the Start menu, and click Control Panel, then click Performance and Maintenance. 2 Click the Administrative Tools icon. 3 Double-click Computer Management, then click Device Manager. 4 Select the specific device from the device category. To expand a device category, double-click the category. 5 In the toolbar, look to the far right for an icon of a monitor with a strike mark through a circle on the front.
If Something Goes Wrong Resolving a hardware conflict The operating system displays the Device Properties dialog box, which provides an array of tabs. They may include: ❖ The General tab, which provides basic information about the device. ❖ The Resource tab, which lists resources assigned to the monitor, optional external DVD-ROM, optional external diskette drive, and other power-using functions. This tab does not appear if the device is not using resources.
If Something Goes Wrong Resolving a hardware conflict 203 5 Check for the error again. 6 If the error recurs, remove the memory module entirely and check for the error again. If removing the memory module eliminates the error, the memory module may be faulty. If the error recurs without the memory module installed, the error is not caused by the memory module. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.
If Something Goes Wrong Resolving a hardware conflict The battery may not be inserted correctly in the computer. Turn off the computer, remove the battery, clean the contacts with a soft dry cloth (if necessary) and replace the battery. See “Removing the battery from the computer” on page 115. The battery may be too hot or too cold to charge properly. If you think this is the probable cause, let the battery reach room temperature and try again.
If Something Goes Wrong Resolving a hardware conflict 205 current on the most recent software and hardware options for your computer, and for other product information. For more information on maximizing battery power see “Charging batteries” on page 105. Keyboard problems If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itself. The keyboard produces unexpected characters. A keypad overlay may be on.
If Something Goes Wrong Resolving a hardware conflict Display problems Here are some typical display problems and their solutions: The screen is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant password feature by pressing Fn and F1 simultaneously. If you have registered a password, press any key, type the password and press Enter. If no password is registered, press any key.
If Something Goes Wrong Resolving a hardware conflict 207 The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Properties. This opens the Display Properties dialog box. The Appearance tab of this dialog box allows you to choose the colors for the screen. The Settings tab allows you to choose the screen resolution. The built-in screen flickers.
If Something Goes Wrong Resolving a hardware conflict The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode, and not simultaneous mode. Small bright dots appear on your TFT display when you turn on your computer. Small bright dots may appear on your screen display when you turn on your PC.
If Something Goes Wrong Resolving a hardware conflict 209 Error-checking Run Error-checking, which analyzes the directories, files and File Allocation Table (FAT) on the disk and repairs any damage it finds: To run Error-checking: 1 Click Start, then click My Computer. 2 Right-click the drive you want to check. 3 On the pop-up menu, click Properties. The drive’s Properties box appears. This feature is not available for CD/DVD drives. NOTE 4 Click the Tools tab. 5 Click the Check now button.
If Something Goes Wrong Resolving a hardware conflict Your data files are damaged or corrupted. Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files. You may also be able to recover lost data using utility software. Consult your network administrator. Some programs run correctly but others do not. This is probably a configuration problem.
If Something Goes Wrong Resolving a hardware conflict 211 DVD-ROM or multi-function drive problems You cannot access a disc in the drive. Make sure the tray which holds the CD-ROM or DVD-ROM is closed properly. Press gently until it clicks into place. Open the tray and remove the disc. Make sure the tray is clean. Any dirt or foreign object can interfere with the laser beam. Examine the disc to see if it is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner.
If Something Goes Wrong Resolving a hardware conflict Some discs run correctly but others do not. Check the type of disc you are using. The DVD-ROM drive supports the Digital Versatile Disc (DVD) formats DVDROM, DVD-R (read-only), plus CD-ROM, CD-R (readonly), and CD-RW (read-only). If the problem is with a data CD or DVD, refer to the software’s documentation and check that the hardware configuration meets the program’s needs.
If Something Goes Wrong Resolving a hardware conflict 213 these devices to work together, several sections in this chapter may apply. Resource conflicts can cause problems when using PC Cards. See “Resolving a hardware conflict” on page 198. Card Information Structure When you insert a PC Card into a slot, the computer attempts to determine the type of card and the resources it requires by reading its Card Information Structure (CIS).
If Something Goes Wrong Resolving a hardware conflict Resolving PC Card problems Here are some common problems and their solutions: The slot appears to be dead. PC Cards that used to work no longer work. Check the PC Card status: 1 Click Start. 2 Click My Computer icon with the secondary button, then click Properties. The System Properties dialog box appears. 3 Click the Hardware tab. 4 Click the Device Manager button. 5 Double-click the PCMCIA adapter.
If Something Goes Wrong Resolving a hardware conflict 215 Hot swapping (removing one PC Card and inserting another without turning the computer off) fails. Follow this procedure before you remove a PC Card: 1 Double-click the PC Card icon on the taskbar. 2 Click Safely remove xxxx, where xxxx is the identifier for your PC Card. The operating system displays a message that you may safely remove the card. 3 Remove the card from the slot.
If Something Goes Wrong Resolving a hardware conflict Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray. Make sure the printer cable is firmly attached to the computer and the printer.
If Something Goes Wrong Resolving a hardware conflict 217 Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack. Check the port settings to make sure the hardware and software are referring to the same COM port. See “Determining the COM port” on page 149.
If Something Goes Wrong Resolving a hardware conflict Wireless networking problems NOTE This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi) networking. The terms and concepts used assume a basic understanding of networks, and may be for more advanced users. If you need assistance or if you are not familiar with the terminology, please see Windows Help and Support or contact your computer technician.
If Something Goes Wrong Resolving a hardware conflict 219 ❖ Check Control Panel's Device Manager to verify that the Wi-Fi adapter is recognized by Windows®, and that the driver is loaded. Carefully note any error messages— these will be very helpful if you should confer with a support technician at a later time. ❖ Verify that the network connection is configured to obtain its Internet Protocol (IP) address dynamically: 1 Click Start, Control Panel. 2 Double-click Network Connections.
❖ ❖ If Something Goes Wrong Resolving a hardware conflict Use the PING command to verify a connection to the gateway at 192.168.1.1 (a default gateway for most wireless routers). ❖ Click Start, then click Run... ❖ Enter Cmd and press Enter. ❖ Enter PING 192.168.1.1 at the command prompt, and press Enter. ❖ If “Request Timed Out” or another error message appears in response, then the problem is probably Wi-Fi-related.
If Something Goes Wrong DVD operating problems 221 The Windows XP wireless management facility does not work. If you are using an external Wi-Fi adapter (a PC Card, USB adapter, or other variety), check if the adapter comes with its own management utility. If it does, the utility may be disabling the Windows XP wireless management facility, in which case you must use the adapter's management utility.
5 If Something Goes Wrong DVD operating problems Verify that your computer recognizes your DVD-ROM drive. To do this: Double-click the My Computer icon on the desktop. The DVD-ROM drive should appear in the list. 6 See “Checking device properties” on page 201 for instructions on using Device Manager to view the DVDROM properties. 7 Check the Toshiba Web site for new information on DVD-ROM drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
If Something Goes Wrong DVD operating problems 5 223 Click OK. DVD titles, games, or applications appear distorted. Having Stretch enabled when your video resolution is set to 800 x 600 can cause distortion. To disable Stretch, follow the instructions below: 1 Right-click the Desktop, select Properties. 2 Select the Settings tab. 3 Select the Advanced Flat Panel tab. 4 Click Disable Display Stretch Feature. 5 Click OK. The screen saver runs while you are watching a movie or title.
7 If Something Goes Wrong Develop good computing habits Click OK. Develop good computing habits Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature. Save your work! See “Computing tips” on page 77 for instructions. On a regular basis, back up the information stored on your hard disk.
If Something Goes Wrong Develop good computing habits 225 Get familiar with all the user’s guides provided with your computer, as well as the manuals that come with the programs and devices you purchase. Your local computer store or book store sells a variety of selfhelp books you can use to supplement the information in the manuals.
If Something Goes Wrong Develop good computing habits 5 In the Restore point description field, enter a name that is descriptive enough to be easily understand in the future, such as “Before installing Brand X Accounting app.” Then click Create. 6 Windows creates the Restore Point and automatically stamps it with the current date and time. Then, at a later time, you can re-establish your Windows configuration using the saved Restore Point. To do this: 1 Click Start. 2 Click Help and Support.
If Something Goes Wrong Develop good computing habits 227 Backing up your data to CDs with Windows XP For most of us, by far the most valuable component of our computer system is the data we have created with it, and stored on its hard disk drive. Since problems with either hardware or software can make the data inaccessible or even destroy it, the next most valuable component of your computer system may be a recent backup of your data.
NOTE If Something Goes Wrong Develop good computing habits Documents and other data files that you create as you work are typically stored in the My Documents folder. You may also wish to back up other important data files stored elsewhere on your hard disk drive, for example: ❖ E-mail files and settings—for Outlook, Outlook Express, or other e-mail apps. Visit the vendors’ Web sites (www.microsoft.com, for example) for detailed instructions.
If Something Goes Wrong Develop good computing habits 229 Favorites (bookmarks) for Internet Explorer and other Web browsers Follow these steps to back up your Favorites for Internet Explorer (ver 5.0 or newer): 1 In Internet Explorer, click File, Import and Export. 2 The Import/Export Wizard will appear. Click Next. 3 Click Export Favorites, Next. (To restore the Favorites to the hard disk drive later you would select Import Favorites from this list.
If Something Goes Wrong Develop good computing habits General tips for installing hardware and software Here are a few tips to help insure safe and easy installation of new hardware (printers, pointing devices, external hard drives, DVD writers, scanners, etc.) and software (applications like Microsoft Office and Adobe Photoshop, or utility software such as special toolbars for your web browser). ❖ Create a Restore Point (see “Saving system configuration with Restore Points” on page 225).
If Something Goes Wrong If you need further assistance 231 1 Back up critical data. 2 Create a Restore Point. 3 Install one item of hardware or software. 4 Restart Windows. 5 Use the new hardware or software for a while, noting any new problems. Make sure that your critical applications (e-mail, business apps, etc.) are working correctly, and verify that important devices are still functioning.
If Something Goes Wrong If you need further assistance Detailed system specifications are available at www.ts.toshiba.com by selecting your particular product and model number, clicking GO, and then clicking the Detailed Specs link from the menu on the left, or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777.
If Something Goes Wrong Other Toshiba Internet Web sites 233 Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Other Toshiba Internet Web sites toshiba.com Worldwide Toshiba corporate site computers.toshiba.com Marketing and product information in the USA accessories.toshiba.com Accessories information in the USA www.toshiba.ca Canada www.toshiba-Europe.com Europe www.toshiba.co.jp/index.htm Japan http://servicio.toshiba.
If Something Goes Wrong Toshiba’s worldwide offices Italy Centro Direzionale Colleoni Palazzo Perseo Via Paracelso 10 20041, Agrate Brianza Milano, Italy Japan Toshiba Corporation, PCO-IO 1-1, Shibaura 1-Chome Minato-Ku, Tokyo, 105-8001 Japan Latin America and Caribbean Toshiba America Information Systems 9740 Irvine Blvd. Irvine, California 92618 USA Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF.
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls. Volume Mute Fn + This hot key enables/disables volume mute on your computer. When volume mute is enabled, no sound will come from the speakers or headphones. 235 5.375 x 8.375 ver 2.3.
Hot Keys Password security Password security This hot key blanks the display. Fn + Without a password The Fn + F1 key combination turns off the display and activates instant security. Using the pointing device or any key will make the display’s content reappear, if no password is set for the current user. With a password The Fn + F1 key combination turns off the display and activates instant security.
Hot Keys Password security 237 3 If you clicked Choose a screen saver, the Screen Saver tab has already been selected. If it is not selected, click the Screen Saver tab. 4 Click the On resume, password protected check box. 5 Click OK. Maintaining security when the battery is not fully charged When the battery is not fully charged (even if the computer is operating on AC power) your display may reappear automatically after a short time.
Hot Keys Power usage mode Power usage mode Fn + This hot key displays the power usage pop-up window and cycles through the battery save modes. Sample power usage modes The properties of each mode are set in the Toshiba Power Management utility. For more information, see “Power Management” on page 167. Standby mode Fn + This hot key places the computer into Standby mode. ❖ A message box displays by default to confirm that the computer is entering Standby mode.
Hot Keys Hibernation mode 239 Hibernation mode Fn + This hot key places the computer into Hibernation mode. ❖ If Hibernation mode is enabled (the default) a message box displays by default to confirm the computer is entering Hibernation mode. You can choose not to display this message box. Sample Hibernation confirmation box ❖ If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using Hibernation” on page 95. 5.375 x 8.375 ver 2.3.
Hot Keys Display modes Display modes Fn + This hot key cycles through the power-on display options. The display modes are: ❖ Built-in display only ❖ Built-in display and external monitor simultaneously ❖ External monitor only Sample display options window In order to use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. Display brightness Fn + This hot key decreases the screen brightness.
Hot Keys Disabling or enabling wireless devices 241 Disabling or enabling wireless devices Fn + This hot key enables and disables the optional wireless devices installed in your computer. The wireless modes are: ❖ All disabled—This disables both the Bluetooth® and Wi-Fi modules. ❖ Wi-Fi enabled—This enables just the Wi-Fi module. ❖ Bluetooth enabled—This enables just the Bluetooth module. ❖ All enabled—This enables both Bluetooth and Wi-Fi.
Hot Keys Keyboard hot keys Keyboard hot keys Fn + This hot key turns the cursor control overlay on and off. Fn + This hot key turns the numeric overlay on and off. Fn + This hot key turns the scroll lock feature on and off. Fn + This hot key toggles the resolution between SVGA (800 x 600), XGA (1024 x 768), and SXGA+ (1400 x 1050). Zooming applications in/out Fn + This hot key turns the Zooming utility to zoomout. For more information, see “TOSHIBA Zooming Utility” on page 177.
Appendix B Power Cord/Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada UL approved CSA approved United Kingdom BS approved Australia Europe AS approved VDA approved NEMKO approved 243 5.375 x 8.375 ver 2.
Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between locations and communication networks. NOTE For more information on using ConfigFree, see the ConfigFree online Help.
Using ConfigFree™ with your Toshiba Computer Getting Started 245 ❖ Profile Settings—The Profiles utility lets you switch between network configurations. For more information, see “Profile Settings” on page 255. ❖ ConfigFree SUMMIT—The ConfigFree SUMMIT utility is used to connect with other ConfigFree users for file sharing. For more information, see “ConfigFree SUMMIT” on page 259. ConfigFree also includes a screen saver that you can customize by adding identifying text to devices.
NOTE Using ConfigFree™ with your Toshiba Computer Getting Started If your computer is not connected to a network, the ConfigFree icon on the taskbar is displayed with an “X.” When you start a search for wireless devices, ConfigFree Launcher displays on your computer desktop. You can then click the appropriate icon on the Launcher to start the desired ConfigFree utilities.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 247 Sample ConfigFree Launcher coming back into view ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities ❖ Location of wireless communication switch (identified with a yellow arrow) ❖ Status of wireless communication switch (on or off) Sample Connectivity Doctor screen Moving the mouse pointer over a wired or wireless network device icon displays information about the device, such as its IP address, subnet mask, and MAC address.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 249 If a problem or potential problem is detected, in most cases, a screen automatically displays showing you the possible cause and solution for the problem. A triangle containing an exclamation point also appears on the Connectivity Doctor screen and an orange frame describes the relevant location. You can also view the possible cause and solution for the problem by clicking the exclamation point.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Search for Wireless Devices The Search for Wireless Devices utility searches for wireless LAN and Bluetooth devices currently used in the neighborhood, and displays information about them on a virtual map. To search for wireless devices: 1 Click the icon in the system tray. 2 Click Search for Wireless Devices. A virtual map appears with a graphical representation of the wireless devices that have been detected.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 251 Sample viewing Wi-Fi devices Creating a new wireless connection NOTE This feature is only supported on systems running Windows XP SP2. To add a new wireless connection to an Access Point: 1 Open the Search for Wireless Devices option from ConfigFree Launcher. 2 Drag and drop the device you want to connect to the PC icon at the center of the map. The Wireless Settings screen appears. 5.375 x 8.375 ver 2.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample dragging a device to the Access Point Sample Wireless settings screen 3 NOTE Enter the SSID/WEP information and connect to the device. After the Access Point is set up and added to the connection list, the system displays the Connection screen rather than the Wireless settings screen. 5.375 x 8.375 ver 2.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 253 Creating a detected device wireless connection The following screen shows an example of Bluetooth devices that are detected using the Search for Wireless Devices option. Moving the mouse cursor over a device icon displays information about the device. Sample viewing Bluetooth devices You can connect to devices shown on the Bluetooth map: 1 Drag and drop the device you want to connect to the PC icon at the center of the map.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample dragging the file to the Bluetooth device icon To be prompted for the device: 1 Drag and drop the file to the Bluetooth radar icon on the ConfigFree Launcher. Sample dragging the file to the Bluetooth radar icon Or, you can right click on the file and select Send to Bluetooth Devices. 5.375 x 8.375 ver 2.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 255 Sample selecting Send to Bluetooth Devices option 2 Choose a file recipient. 3 Click Send. NOTE During a file transfer, connecting and disconnecting to the selected device will occur automatically. Disconnecting from a Bluetooth device To disconnect from a Bluetooth device: 1 Place the cursor on top of the connected line. The icon changes to a pair of scissors. 2 Click to disconnect from the device.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities office and at home can set up profiles to handle these networking environments. A profile contains the currently configured network settings on the computer, as well as information about any network devices. The following settings can be saved (or “captured”) in a profile: ❖ Internet settings — includes LAN settings (proxy server settings) and the address of a home page that opens automatically when Internet Explorer starts.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 257 8 Click the icon at the bottom of the screen to display more capture options. 9 Under Captured Items, select the items you want to capture for this profile. 10 If connecting with a wireless network, select the desired Auto Switch Settings. (These options are unavailable if wireless devices have been disabled.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample expanded Add Profile screen NOTE The online help provides real-world examples of setting up profiles for different networking environments. After you set up one or more profiles, you can check their settings and fine-tune them as necessary. Profiles can also be imported and exported. This feature is useful when transferring profile settings to other computers.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 259 ConfigFree SUMMIT The ConfigFree SUMMIT utility is a convenient way to share files with other users and to transfer files between your computers at home and at work. This utility is faster and more dependable than sending the files via email. Use this utility, which handles files regardless of size, to distribute presentations, reports, or music files to meeting attendees or to users at different locations.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample of users attending SUMMIT meeting (user icons appear on SUMMIT table) Files can be shared with one user or all users attending the meeting. ❖ To share a file with one user, drag and drop the file on the user’s icon. NOTE Only the SUMMIT Host (the initiator) can share files with multiple users by this method. SUMMIT users can share a file with only one other user. 5.375 x 8.375 ver 2.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 261 Sample of sharing a file with one user ❖ To share a file with all users, drag the file to the center of the SUMMIT table where users can access it as desired. NOTE If you are the Host of the summit, and drag a file to the center of the SUMMIT table, it will automatically be sent to all SUMMIT users who can then accept or decline the file as desired. Sample of sharing a file with all users 5.375 x 8.375 ver 2.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Participating users must be connected by LAN, wireless LAN, or Bluetooth (PAN). Firewall software may prevent ConfigFree SUMMIT from working. NOTE Using ConfigFree SUMMIT To host a ConfigFree SUMMIT: 1 Click the icon in the system tray. 2 Click SUMMIT. Other users appear on the SUMMIT main window. SUMMIT can also be started from the ConfigFree Launcher. NOTE 3 Select the appropriate users and invite them to the SUMMIT meeting.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 263 1 Drag and drop the file to the Wireless radar icon on the ConfigFree Launcher. 2 Right click on the file and choose a file recipient. 3 Click Send. An Access Point may not always be available. To find out how to use Quick Connect to launch ConfigFree Summit, see “Direct Link Toshiba Device” on page 265. Quick Connect The Quick Connect feature includes two options: ❖ Toshiba Wireless Projector.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities To review the current Toshiba Wireless Projector settings and change them if necessary: 1 Click the 2 Move the mouse pointer to Toshiba Wireless Projector (DPJ), then click Settings. The Quick Connect properties dialog box appears. 3 Complete the settings. Refer to the online help if necessary. 4 Click OK. NOTE icon in the system tray.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 265 The wireless LAN configuration returns to the settings that were last used before the Quick Connect function was started: ❖ If the Toshiba Wireless Projector utility is closed. ❖ If you select Toshiba Wireless Projector (DPJ) from the ConfigFree tray menu (this disconnects the wireless LAN connection). ❖ If you select a profile from the ConfigFree tray menu or when you disable a wireless device. ❖ If you close ConfigFree.
Using ConfigFree™ with your Toshiba Computer Using the Automatic Switch Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network configuration you use in your office to the one you use at home. The Auto Switch feature contains options for automatically switching between wired and wireless devices.
Using ConfigFree™ with your Toshiba Computer Semi-Automatic Switch Feature 267 1 Right-click the icon in the system tray. 2 Click Auto Switch. The Auto Switch dialog box appears. 3 Select the Auto Switch (SSID) tab. 4 Select the profile to be automatically selected when the SSID is detected, then click Add. The profile is moved to the List of target SSIDs and profiles. 5 Repeat the previous step for each additional profile you want to select.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide.
Glossary DMA direct memory access DIMM dual inline memory module DOS disk operating system DPI dots per inch DSTN dual supertwist nematic DVD digital versatile (or video) disc 269 DVD-ROM digital versatile (or video) disc read-only memory ECP enhanced capabilities port EPROM erasable programmable read-only memory FAT file allocation table FCC Federal Communications Commission FIR fast infrared GB gigabyte HDD hard disk drive HTML Hypertext Markup Language IEEE Institute of Ele
Glossary RAM random access memory RFI radio frequency interference ROM read-only memory RTC real-time clock SCSI small computer system interface SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter TFT thin film transistor USB universal serial bus URL uniform resource locator WAN wide area network www World Wide Web Terms The following terms may appear in this user’s guide.
Glossary 271 application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. B backup — A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged. basic input/output system (BIOS) — See BIOS. baud rate — The speed at which a communication device, such as a printer or modem, transmits information.
Glossary byte — A sequence of eight bits. A byte is the smallest addressable unit of data. See also bit, gigabyte, kilobyte, megabyte. C cache — A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer’s main memory. See also CPU cache, L1 cache, L2 cache. CD — An individual compact disc. See also CD-ROM.
Glossary 273 controller — A device that controls the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and printers all require controllers. CPU — See central processing unit (CPU). CPU cache — A section of very fast memory residing between the CPU and the computer’s main memory that temporarily stores data and instructions the CPU will need to execute commands and programs. See also cache, L1 cache, L2 cache.
Glossary disk — A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as diskettes and hard disks. Compare disc. See also diskette, hard disk. disk drive — The device that reads and writes information and programs on a diskette or hard disk. It rotates the disk at high speed past one or more read/write heads.
Glossary 275 DVD-ROM (digital versatile [or video] disc read-only memory) — A very high-capacity storage medium that uses laser optics for reading data. Each DVD-ROM can hold as much data as several CD-ROMs. Compare CD-ROM. E emulation — A technique in which a device or program imitates another device or program. enable — To turn on a computer option. See also disable. executable file — A computer program that is ready to run. Application programs and batch files are examples of executable files.
Glossary frontside bus — The primary pathway (bus) between the CPU and the computer’s main memory. Also called “system bus.” See also bus. function keys — The keys labeled F1 through F12, typically located on the keyboard. Their function is determined by the operating system and/or individual programs. G gigabyte (GB) — A unit of data equal to 1,073,741,824 bytes (1024 x 1024 x 1024 bytes). 1 Gigabyte (GB) means 1000 x 1000 x 1000 = 1,000,000,000 bytes using powers of 10.
Glossary 277 hot key — (1) A feature in which certain keys in combination with the Fn key can set system options or control system parameters, such as the battery save mode. (2) A key or combination of keys that activates a memory resident program. hot swapping — The ability to add or remove devices from a computer while the computer is running and have the operating system automatically recognize the change. I icon — A small image displayed on the screen that represents a function, file, or program.
Glossary liquid crystal display (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter over the electrodes permits only non-polarized light to pass to the surface of the display, creating light and dark pixels.
Glossary 279 multi-function drive — A DVD drive that can read and write to CD and DVD media. multimedia — A combination of two or more media, such as sound, animation, and video in a computer program or presentation. Musical Instrument Digital Interface — See MIDI. N network — A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail.
Glossary peripheral — Any device, such as a printer or joystick, that is attached to the computer and controlled by the computer’s CPU. pixel — Short for “picture element.” The smallest dot that can be produced on a screen or printer. Plug and Play — Generally, refers to the computer’s ability to automatically configure itself to work with peripheral devices.
Glossary 281 resolution — A measure of the sharpness of the images that can be produced by a printer or displayed on a screen. For a printer, resolution is expressed in dots per inch (dpi). For a screen, it is expressed as the number of pixels available horizontally and vertically. restart — Synonymous with reboot. To reset the computer by reloading the operating system without turning the computer off. See also boot. RJ11 — A modular connector used on most U.S.
Glossary system disk — A diskette that contains the operating system files needed to start the computer. Any diskette can be formatted as a system disk. A system disk is also called a “bootable disk” or a “startup disk.” Compare non-system disk. system prompt — The symbol (in the MS-DOS® operating system, generally a drive letter followed by a “greater than” sign) indicating where users are to enter commands. T Toshiba tablet pen — The writing instrument used with the tablet.
Index A AC power light 51 accessories computer lock cable 75 audio .
Index message 195 not accessing disk drives 194 running on battery power 102 setting up 46, 56 warning resume failure message 194 computing tips 77 configuring hard drive passwords 185 password 181 connecting DVD drive 124 external monitor 128 external USB keyboard 63 external USB mouse 62 modem to telephone line 66 printer 63 USB-compatible mouse 62 control buttons 67 critical applications 3 cursor control overlay 82 customizing taskbar 142 D desktop browsing style 144 changing styles 144 personaliz
Index general hardware problem 198 non-system disk or disk error 195, 210 problem with display settings/ current settings not working with hardware 207 program has performed an illegal operation 192 warning resume failure 194 Error-checking 78, 209 Ethernet LAN Port disabling 150 using 150 expansion memory slot 57 external monitor connecting 128 F FAT (File Allocation Table) 209 FCC Notice “Declaration of Conformity Information” 3 FCC requirements 4 files .
Index I M IBM 101-key enhanced keyboard 79 icon safety 39 Industry Canada requirement 4 instant password 184 hot key 184 Internet 152 bookmarked site not found 197 chat rooms 154 connecting to 153 news groups 154 overview 152 slow connection 197 URL address not found 197 Internet Service Provider (ISP) 153, 155 IRQ (Interrupt Request) 199 main battery removing 115 Master password 184 memory problem solving 202 removing expansion slot cover 57 memory module inserting 59 removing 61 microphone using
Index P password creating 182 disabling 183 hard disk drive 182 instant 184 power-on 181 types 181 user-level 181, 184 passwords 181 PC Card checklist 213 CIS (Card Information Structure) 213 computer stops working 214 errors 215 hot swapping 137 hot swapping fails 215 inserting 136 modem default 149 not recognized 215 problem solving 212, 214 removing 137 slot 135 PC Card slot 135 playing audio 88 Plug and Play 199 port COM 149 power cable connectors 243 computer will not start 193 energy-saving features
Index not responding 194 missing files/trouble accessing a disk 208 modem not receiving or transmitting 217 no sound 212 non-system disk or disk error 195, 210 PC Card 212 checklist 213 error occurs 215 hot swapping fails 215 not recognized 215 slot appears dead 214 power and batteries 203 printer 216 program not responding 191 program not working properly 210 screen does not look right/flickers 207 Startup options 196 system resources 199 URL address not found 197 warning resume failure 194 Windows w
Index Standby command 92, 98 Standby mode 92 hot key 238 starting a program 83 starting the computer password 184 Startup menu problem solving 196 stored data protection 2 T taskbar customizing 142 toolbars displaying in a window 147 Toshiba Internet Web sites 233 registering computer 48 worldwide offices 233 TOSHIBA Console 165 Toshiba Hardware Setup 169, 172 Toshiba tablet pen 132 TouchPad disabling 68 enabling 68 using 67, 68 traveling tips 122 troubleshooting DVD player general problems 221 DVD-ROM dr
Index World Wide Web 152 5.375 x 8.375 ver 2.
