User’s Manual TECRA M5
Copyright © 2006 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
Following information is only for EU-member states: The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
Table of Contents Preface General Precautions Chapter 1 Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10 Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 Options . . . .
Chapter 4 Operating Basics TOSHIBA Dual Pointing Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3 Using the USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . .4-10 Changing Slim Select Bay modules . . . . . . . . . . . . . . . . . . . . . . . . . .4-11 Using optical disk drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 8 Optional Devices PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 ExpressCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Battery pack . . . . . . . . . . . . . . . . . . . . . .
Appendix C Wireless LAN Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 Supported Frequency Sub-bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 Appendix D Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health . . . . . . . . . . . . . . . . D-3 Regulatory statements. . . . . . . . . . . . . . . . .
Preface Congratulations on your purchase of the TECRA M5 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TECRA M5 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 7, HW Setup, explains how to configure the computer using the HW Setup program and TPM. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly. Chapter 10, Legal Footnotes, provides Legal Footnote information related to your computer.
Preface Display S ABC Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left. Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read.
Preface xii User’s Manual
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phones Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft® Windows XP Professional ■ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1-2 Microsoft® Windows XP Professional Microsoft Internet Explorer TOSHIBA Utilities TOSHIBA Wireless Key Logon TOSHIBA SD Memory Boot Utility DVD Video Player TOSHIBA Dual Pointing Device utility TOSHIBA Power Saver TOSHIBA Mobile Extension TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool TOSHIBA Control
Introduction Documentation and Backup Media ■ TECRA M5 Portable Personal Computer User’s Manual ■ TECRA M5 Quickstart ■ Instruction Manual for Safety & Comfort ■ Warranty information ■ Product Recovery DVD-ROM If any of the items are missing or damaged, contact your dealer immediately.
Introduction Memory Slots 512, 1,024, or 2,048 MB memory modules can be installed in the two memory slots for a maximum of 4,096 MB system memory. Video RAM Part of system memory is used for Video RAM. Up to 128 MB of RAM is provided for video display. Legal Footnote (Main Memory) For more information on the Legal Footnote regarding Main Memory, please refer to the Legal Footnotes section in Chapter 10. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack.
Introduction Disks Hard disk drive (HDD) Available in five sizes. ■ 40.0 billion bytes (37.26 GB) ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) ■ 100.0 billion bytes (93.16 GB) ■ 120.0 billion bytes (111.79 GB) Part of the space on the hard disk drive is reserved as administration space. Legal Footnote (HDD Capacity) For more information on the Legal Footnote regarding HDD Capacity, please refer to the Legal Footnotes section in Chapter 10.
Introduction DVD Super Multi drive Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed, CD-RW at maximum 10 speed, DVD-RW and DVD+RW at maximum 4 speed, DVD-R DL at maximum 2 speed, DVD+R DL at maximum 2.4 speed.
Introduction Legal Footnote (Graphics Processor Unit (“GPU”)) For more information on the Legal Footnote regarding Graphics Processor Unit (“GPU”), please refer to the Legal Footnotes section in Chapter 10. Keyboard Built-in 85 keys or 87 keys, compatible with IBM® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. Refer to Chapter 5, The Keyboard, for details.
Introduction SD card This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants that use SD card flash-memory. Refer to Chapter 8, Optional Devices. Multimedia Sound system A Windows sound system compatible sound system provides internal speakers and a microphone as well as supports jacks for an external microphone and headphones. Video-out jack (S-Video) The video out jack lets you transfer video data to external devices.
Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G). ■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g) ■ Theoretical maximum speed: 11Mbps (IEEE802.11b) ■ Frequency Channel Selection (5 GHz: Revision A / 2.
Introduction Security Security lock slot Connects security lock to anchor the computer to a desk or other large object. Slim Select Bay latch A Slim Select Bay module can be secured by the Slim Select Bay latch fixed with a Slim Select Bay lock screw in the lock position. The Slim Select Bay lock screw is inserted in the unlock position when purchased. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use.
Introduction User’s Manual Keypad overlay A ten-key pad is integrated into the keyboard. Refer to the Keypad overlay section in Chapter 5, The Keyboard, for instructions on using the keypad overlay. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Instant security A hot key function blanks the LCD screen and disables the computer providing data security.
Introduction HDD Protection Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks, and other such occurrences in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact. Refer to the Using the Hard Disk Drive (HDD) Protection section in Chapter 4, Operating Basics, for details.
Introduction TOSHIBA Controls This utility lets you assign applications or functions to the TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist). To access this utility, click start, point to Control Panel, choose Printers and Other Hardware and click the Toshiba Controls icon.
Introduction Bluetooth cannot be used in models that do not have a Bluetooth module installed. TOSHIBA SD Memory Boot Utility The TOSHIBA SD memory boot utility allows you to create a bootable SD memory card to start the system. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows. Click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD Memory Boot Utility.
Introduction User’s Manual TOSHIBA Dual Pointing Device utility This utility has the following functions: To disable/enable TOSHIBA Dual Pointing Device with Fn + F9 keys. To customize the functions of TOSHIBA Dual Pointing Device easily. TOSHIBA Mic Effect TOSHIBA Mic Effect is a utility used to enable comfortable calls with echo cancellation function.
Introduction TOSHIBA SD The TOSHIBA SD memory boot utility allows you Memory Card Format to create a bootable SD memory card. This utility allows you to format an SD memory card by the SD standard format. CD/DVD Drive Acoustic Silencer This utility allows you to configure the read speed of the optical disc drive.
Introduction Advanced Port Replicator III Plus The Advanced Port Replicator III Plus provides the ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™ (IEEE1394) port, line-in jack and line-out jack, External monitor port, Universal Serial Bus port (USB2.0) × 4, LAN jack, Modem jack, Serial port, Parallel port. Hard disk drive You can increase your computer’s data storage capacity with additional hard disk drives.
Introduction 1-18 User’s Manual
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons) For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Chapter 10. Front with the display closed The following figure shows the computer’s front with its LCD display panel in the closed position.
The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality. ■ Always turn off WiFi or Bluetooth functionality if the PC is near automatic control equipment or appliances such as automatic doors or fire detectors.
The Grand Tour Do not block the cooling vents. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury. External monitor port This external monitor port lets you connect an external video display. i.LINK (IEEE1394) port This port allows you to connect an external device, such as a digital video camera for high-speed data transfer.
The Grand Tour Right side The following figure shows the computer’s right side. Volume control Headphone jack Microphone jack Slim Select Bay USB ports Serial port The right side of the computer Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Headphone jack A 3.
The Grand Tour Back side The following figure shows the computer’s back side. LAN active indicator (orange) Video-out jack Modem jack LAN jack Link indicator (green) DC IN 15V jack The back side of the computer Video-out jack Plug an S-Video cable into this jack for video-out. The S-Video cable carries video signal. DC IN 15V jack The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer.
The Grand Tour LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). The LAN has two indicators. Refer to Chapter 4, Operating Basics, for details. ■ Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. ■ Do not connect the LAN cable to a power supply.
The Grand Tour Battery lock Slide the battery lock to release the battery pack for removal. Battery pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes. Notches Notches on the computer engage hooks on the Advanced Port Replicator III Plus to ensure a secure connection. Battery release latch Slide and hold this latch to release the battery pack for removal.
The Grand Tour HDD pack cover screw One screw secures the HDD cover. Hard disk drive cover A HDD disk drive pack is under this, which can be removed and reinstalled. For more information on how to remove or reinstall the Hard disk drive pack, refer to the section on the in Chapter 8, Optional Devices. Front with the display open This section shows the computer with the LCD display panel open. Refer to the appropriate illustration for details.
The Grand Tour User’s Manual Fingerprint Sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented. ■ Disable the password-protected screen-saver when returning from power-saving (standby) mode. ■ Power-on Security and Single Sign-on feature.
The Grand Tour TOSHIBA Presentation button Press this button to display the same image on the internal and external monitor or to use multi-monitor display (Windows XP Only). The default setting is “Presentation (Same Image 1024x768)”. The same image is displayed on the internal and external monitor with screen resolution 1024x768. In the setting of “Presentation (Different Image)”, you can use the internal and external monitors as a widescreen. This setting is supported in Windows XP only.
The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. System indicators User’s Manual SD card The SD card indicator glows green when the computer is accessing the SD card slot. DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Power The Power indicator glows green when the computer is on.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers. When the Caps Lock indicator glows the keyboard is in all-caps mode. Caps Lock indicator Caps Lock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase.
The Grand Tour USB floppy disk drive (optional) The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. USB connector Disk-In-Use Indicator Floppy disk slot Eject button USB floppy disk drive USB connector Insert this connector into one of the USB ports of your computer. Disk-In-Use Indicator This indicator lights when the floppy disk is being accessed. Floppy disk slot Insert a floppy disk in this slot.
The Grand Tour Optical disk drives One of the following Optical disk drives is installed in the computer: DVDROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical disk drives section in Chapter 4, Operating Basics.
The Grand Tour Formats The drives support the following formats: ■ ■ ■ ■ CD-ROM DVD-ROM CD-DA Photo CD™ (single/multi-session) ■ CD-ROM XA Mode 2 (Form1, Form2) ■ ■ ■ ■ ■ DVD -Video CD-Text CD-ROM Mode 1, Mode 2 Enhanced CD (CD-EXTRA) Addressing Method 2 DVD-ROM&CD-R/RW drive The full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes for details.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read the Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Select a work area that has: ■ a well-designed and functioning ventilation system that does not forcefully direct air on you ■ good air circulation ■ a comfortable ambient temperature and relative humidity.
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location. Your PC may fall, causing damage to the PC or possibly injury. ■ Never leave the power to your PC on continuously for more than 24 hours. Turn the power off when this product is not in use.
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Posture and positioning of the computer ■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to the floor. ■ Keep head level, or bent slightly forward, forward facing, and balanced. Generally the head is in-line with the torso.
Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user.
Getting Started Strategic Rest Breaks Take short, strategically spaced rest breaks to avoid eye strain and body discomforts. For more specific recommendations on the safety and comfort of your computer environment, customers in the United States may visit the United States Department of Labor, Occupational Safety & Health Administration website at: http://www.osha.gov/SLTC/etools/computerworkstations/ Other Things to Note ■ Never turn off the power while an application is running.
Getting Started ■ Never plug the AC adaptor or Battery Charger into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury. ■ Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use.
Getting Started Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack AC adaptor’s DC output plug Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.
Getting Started Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicators section in Chapter 6, Power and Power-Up Modes. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time. ■ If the USB floppy disk drive is connected, make sure it is empty.
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby Mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1. If you have entered data, save it to the hard disk or to a storage media. 2. Make sure all disk (disc) activity has stopped, then remove the CD/DVDs or floppy disk.
Getting Started ■ Before entering Standby Mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Standby Mode. The computer or the module could be damaged. ■ Do not remove the battery pack while the computer is in Standby Mode (unless the computer is connected to an AC power source). Data in memory will be lost.
Getting Started Standby limitations Standby will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise. Hibernation Mode The Hibernation Mode feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The Hibernation Mode feature does not save the status of any peripheral devices.
Getting Started Starting Hibernation Mode You can also enable Hibernation Mode by pressing Fn + F4. Refer to Chapter 5, The Keyboard, for details. To enter Hibernation Mode, follow the steps below. 1. Click start. 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box. 4. Click Hibernate. Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below. 1.
Getting Started There are three ways to reset the computer system: 1. Click start then click Turn off computer. From the Turn off computer menu select Restart. 2. Press Ctrl + Alt + Del to display the Windows Task Manager, then select Shut Down and Restart. 3. Press the power button and hold it down for five seconds. Wait 10 to 15 seconds, then turn the power on again by pressing the power button.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the AccuPoint To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer.
Operating Basics 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard.
Operating Basics ■ Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate ■ Soaked or swollen finger (e.g. after taking bath) ■ Injured finger ■ Wet finger ■ Soiled or oily finger ■ Extremely dry skin condition on finger Observe the following to improve the fingerprint recognition success rate. ■ Enroll two or more fingers.
Operating Basics ■ Toshiba does not guarantee that this fingerprint recognition technology will be error-free. ■ Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility. The following illustrations show the correct way to slide your finger over the recognition sensor.
Operating Basics Set Up Procedure Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required authentication data using the “User Enrollment” Wizard. ■ The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration. ■ Up to 21 fingerprint patterns can be registered on this sensor. 1.
Operating Basics Window Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the PCs, as user selection can be skipped. Fingerprint Authentication Procedure 1. Start up the computer. 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor.
Operating Basics How to Enable Fingerprint Power-on Security Settings It is necessary to first enroll your fingerprint with the Protector Suite QL application prior to enabling and configuring the Fingerprint Power-on Security System. Check that your fingerprint is enrolled before configuring the settings. See Manual for Fingerprint Registration/Enrollment instructions. 1. Swipe your finger across the Fingerprint Sensor. 2. MENU appears in the lower right corner of the screen.
Operating Basics Fingerprint utility limitations TOSHIBA does not guarantee that the Fingerprint utility technology will be completely secure or error-free. TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Operating Basics Using the USB floppy disk drive (optional) The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. Connecting the USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Make sure the connector is right side up and properly aligned with the socket.
Operating Basics Changing Slim Select Bay modules This section explains how to change modules in the Slim Select Bay. The illustrations show replacement of the optical disk drive with the Slim Select Bay HDD adaptor. Therefore, the text refers to those modules. However, the procedures are the same for any of the modules: DVD-ROM&CD-R/RW drive, DVD Super Multi drive, HDD adaptor and 2nd battery pack. To avoid injury, do not put your hand into the Slim Select Bay slot.
Operating Basics Inserting a module Insert the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2. If you want to lock the Slim Select Bay HDD adaptor, set the Slim Select Bay lock screw in the hole for the lock position. The lock screw is inserted in the unlock position at the time of purchasing.
Operating Basics Loading discs To load CD/DVDs, follow the steps below. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject button Pressing the eject button 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray.
Operating Basics When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat. ■ Do not touch a laser lens and its circumference portion. Doing so could cause misalignment. ■ Prevent foreign objects from entering the drive.
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical disk drives section. ■ Refer to the Writable discs section in Chapter 2 for details about the types of writable CD/DVD discs.
Operating Basics ■ Do not run software such as a screen saver which can put a heavy load on the CPU. ■ Operate the computer at full power. Do not use power-saving features. ■ Do not write while a virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. ■ Do not use hard disk utilities, including those intended to enhance hard disk drive access speeds.
Operating Basics Writing CD/DVDs on DVD Super Multi drive You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM discs. The following applications for writing are provided: RecordNow!, and DLA licensed by Sonic Solutions, and InterVideo’s WinDVD Creator Platinum. ■ Refer to the Writable discs, Chapter 2 for the details about the types of writable CD/DVD discs. ■ Do not turn off the power of the optical disk drive while the computer is accessing the drive.
Operating Basics Before writing or rewriting ■ Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/ +RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Operating Basics DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Hitachi Maxell Ltd. This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 5 speed (DVD-RAM), 2 speed (DVD-R DL) and 2.4 speed (DVD+R DL). ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur.
Operating Basics ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver, which can put a heavy load on the CPU. ■ Operate the computer in the full-power mode. Do not use power-saving features. Be careful not to write to the wrong drive. ■ Do not write while a virus check software is running. Wait for it to finish and then disable virus detection programs including any software that checks files automatically in the background.
Operating Basics ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste. The original data will be lost if there is a write error. Discs created in DVD-R DL (Layer Jump Recording) cannot be read. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Click the Options button ( ) on the RecordNow! Console to open the Options panels. 2. Select the Data in the left-side menu. 3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button.
Operating Basics 4. Click the Advanced tab in the System Properties window. 5. Click the Settings icon in the “Performance” section. 6. Click the Advanced tab in the Performance Options window. 7. Click the Change icon in the “virtual memory” section. 8. Select the Custom size button in the Virtual Memory window. 9. Specify much higher values for “Initial size” and “Maximum size.” 10. Click the Set button in the Virtual Memory window. 11. Click the OK button in the Virtual Memory window.
Operating Basics ■ WinDVD Creator cannot edit or play copy protected content. ■ Do not change display settings while using WinDVD Creator. ■ Do not enter standby/Hibernation Mode while using WinDVD Creator. ■ Do not operate WinDVD Creator immediately after turning on the computer. Please wait until all disk/disc drive activity has stopped. ■ When recording to a DV-Camcorder, to ensure you capture all of your data, let the camcorder record for a few seconds before you begin recording your actual data.
Operating Basics 3. About Disc Manager ■ WinDVD Creator can edit one play list on a disc. ■ WinDVD Creator might show a different thumbnail than you previously set in CE (Consumer Electronics) DVD-RAM recorder. ■ Using the Disc Manager, you can edit DVD-VR format on DVD-RAM, DVD+VR format on DVD+RW, and DVD-Video format on DVD-RW. 4. About recorded DVDs ■ Some DVD-ROM drives for personal computers or other DVD players may not be able to read DVD-R/+R/-R DL/+R DL/-RW/+RW/-RAM discs.
Operating Basics 3. Always handle floppy disks with care, to prevent the loss of stored data. Always apply the floppy disk label in the correct location. Never apply a new label on top of an existing one. The label could come loose and damage the floppy drive. 4. Never use a pencil for writing on a floppy disk label. Pencil lead dust could cause a system malfunction. Always use a felt-tipped pen. When writing a title on a label, first write on the label, then apply the label to the floppy disk. 5.
Operating Basics SigmaTel Control Panel SigmaTel Control Panel lets you control some of the audio settings. Follow the steps below to launch the SigmaTel Control Panel: 1. Click start and click Control Panel. 2. If you are viewing the Control Panel in Category View, click on Switch to Classic View. 3. Double-click the SigmaTel Audio icon. Volume control To adjust the audio volume in Windows for both playback and recording, click the Levels tab.
Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).
Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). ■ Never connect the built-in modem to a key telephone system for residences or offices.
Operating Basics Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner. Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices.
Operating Basics Security ■ TOSHIBA strongly recommend that you enable WEP (encryption) functionality, otherwise your computer will be open to illegal access by an outsider using a wireless connection. If this occurs, the outsider may illegally access your system, eavesdrop, or cause the loss or destruction of stored data. ■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof.
Operating Basics Release Notes related to the Bluetooth™ Stack for Windows® by TOSHIBA 1. Install: On Windows2000 or Windows XP, Bluetooth™ Stack for Windows® by TOSHIBA does not have a digital signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth™ Stack. 3. Multi User: On Windows XP, the use of Bluetooth is not supported in a multi-user environment.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Operating Basics Connecting LAN cable To connect a LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting a LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. ■ Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur. ■ Do not connect any power supplying device to the LAN cable that is connected to the LAN jack.
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the LCD display screen.
Operating Basics Using the Hard Disk Drive (HDD) Protection This computer has a function for reducing the risk of damage on hard disk drive. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks, and other such occurrences in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact.
Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting. The window can also be started from the icon on the Taskbar, or from the Control Panel. TOSHIBA HDD Protection Properties HDD Protection You can choose whether to enable or disable HDD Protection.
Operating Basics Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Details Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds. HDD Protection Message Specify whether to display a message when HDD Protection is active.
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are six types of keys: typewriter keys, function keys, soft keys, Hot keys, Windows special keys and keypad overlay.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Dual Pointing Device. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key or press the Dual Pointing Device. Power save mode: Pressing Fn + F2 changes the power save mode.
The Keyboard Display selection: Press Fn + F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to the internal LCD. Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD screen brightness in decrements.
The Keyboard Dual Pointing Device: Pressing Fn + F9 in a Windows environment enables or disables the Dual Pointing Device function. When you press these hot keys, the current setting will change and be displayed as an icon. LCD screen resolution selection: Press Fn + Space keys to change the display resolution. Each time when you press these hot keys, the LCD screen resolution changes as follows: The available resolution depends on the model.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the figure below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
The Keyboard 5-10 User’s Manual
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power conditions continued Power on AC adaptor connected AC adaptor not connected 6-2 Power off (no operation) 2nd battery fully charged • Operates • No charge • No charge • LED: 2nd Battery green • LED: 2nd Battery green DC IN green DC IN green 2nd Battery partially charged or no charge • Operates • Charge*2 • LED: 2nd Battery orange DC IN green • Quick charge*2 • LED: 2nd Battery orange DC IN green No 2nd battery installed • Operates • No charge • LED: 2nd Battery off D
Power and Power-Up Modes Power conditions continued Power on AC adaptor connected 2nd battery charge is above low battery trigger point • Operates • LED: 2nd Battery off DC IN off 2nd battery charge is below low battery trigger point • Operates • LED: 2nd Battery flashes orange DC IN off 2nd battery charge is exhausted Computer shuts down *3 No 2nd battery is installed • No operation*5 • LED: 2nd Battery off DC IN off Power off (no operation) 2nd battery indicator refers to the Slim Select Bay in
Power and Power-Up Modes Flashing orange The battery charge is low. The AC adaptor must be connected to recharge the battery. Orange Indicates the AC adaptor is connected and charging the battery. Green Indicates the AC adaptor is connected and the battery is fully charged. No light Under any other conditions, the indicator does not light. If the battery pack becomes too hot while it is being charged, the charge will stop and the Battery indicator will go out.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Green Indicates power is being supplied to the computer and the computer is turned on. Flashing orange Indicates power is being supplied to the computer while the computer is in Standby Mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User’s Manual. Other battery packs have different voltage and terminal polarities.
Power and Power-Up Modes High capacity battery pack (option) An optional High capacity battery pack is installable instead of a main battery pack. The connection method of High capacity battery pack is the same as that of main battery pack. ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of battery packs can cause death, serious injury or property damage.
Power and Power-Up Modes 8. Never store a battery pack in an area of high humidity. This could cause a fire or explosion possibly resulting in serious injury. 9. Never expose a battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device could fail, causing it to overheat or ignite resulting in caustic liquid leakage, or explosion or fire, possibly resulting in death or serious injury. 10.
Power and Power-Up Modes 15. Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture. 16. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1. Use only battery packs recommended by TOSHIBA as replacements. 2.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation Mode (so you don’t lose data) and automatically turns off.
Power and Power-Up Modes Battery charging notice The battery may not charge right away under the following conditions: ■ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10° to 30°C (50° to 88°F). ■ The battery is nearly completely discharged. Leave the AC adaptor connected for a few minutes and the battery should begin charging.
Power and Power-Up Modes Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type State and Retention Time High capacity battery pack (8800mAh) about 12 days (Standby Mode) about 115 days (Boot mode) Extended capacity battery pack (7050mAh) about 9 days (Standby Mode) about 95 days (Boot mode) Battery pack (4700mAh) about 6 days (Standby Mode) about 60 days (Boot mode)
Power and Power-Up Modes ■ If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. ■ Store spare battery packs in a cool dry place out of direct sunlight. Replacing the battery pack The battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging. It will need to be replaced when it reaches the end of its operating life.
Power and Power-Up Modes To install a battery pack, follow the steps below. Do not touch the battery release latch while holding the computer. Or you may get injured by the dropped battery pack by unintentional release of the battery release latch. 1. Insert the battery pack all the way to the end (1). 2. Make sure that the battery pack is securely in place and the battery safety lock (2) is in the lock position ( ). Battery pack Battery lock 1 2 Securing the battery pack 3. Turn your computer over.
Power and Power-Up Modes ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy disk or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place. ■ When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or copy-and-paste the character string.
Power and Power-Up Modes User Token field ■ Create (button) You can use an SD card token, instead of entering the password. After you have registered a password, insert an SD card in SD card slot and click Create. You can use an SD card of any capacity, but it must be formatted correctly. If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format.
Power and Power-Up Modes Starting the computer by password If you have already registered a password, there are three ways to start the computer: ■ Insert an SD card token before you turn on the computer. The computer will start normally, without displaying a password prompt. ■ Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint Power-on Security.
Power and Power-Up Modes Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation. Refer to Chapter 5, The Keyboard for details. Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel.
Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup. HW Setup window The HW Setup window contains the following tabs: General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config, Parallel/Printer and USB.
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you select the display to be used when the computer is booted.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive*1, CD-ROM*2 and LAN (Default). FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: floppy disk drive*1, HDD, CD-ROM*2 and LAN.
HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Slim Select Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot. A bar will appear only under the selected device. 3. Use the left/right cursor keys to highlight the boot device you want and press Enter.
HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD -> 2nd HDD -> USB (Default) The priority is set as built-in HDD -> 2nd HDD -> USB. 2nd HDD -> Built-in HDD -> USB The priority is set as 2nd HDD -> built-in HDD -> USB. Built-in HDD -> USB -> 2nd HDD The priority is set as built-in HDD -> USB -> 2nd HDD.
HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key (PS/2 keyboard only). Disabled No Fn key equivalent (Default).
HW Setup CPU This function lets you set the CPU operating mode. This option is displayed only on models with an Intel Core Duo processor. Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary (Default).
HW Setup Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Operating system sets devices that it can control (Default). Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional.
HW Setup Configuring the Execute-Disable Bit Capability and TPM The configurations for the Execute-Disable Bit Capability and TPM are carried out in the BIOS setup program. Notes before using the BIOS Setup ■ In most cases, changes to the system’s configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.
HW Setup Ending the BIOS Setup Program Halfway The configuration settings can be terminated halfway without saving any of the changes made. 1. Press the Esc key. The “Exit without saving? (Y/N)” message is displayed. 2. Press the Y key. The BIOS setup program will end. Execute-Disable Bit Capability This setting, which is displayed on the first page of the setup screen, configures the Execute-Disable Bit function of the CPU.
HW Setup The operating procedure is as follows: 1. Move the cursor to the Clear TPM Owner setting and press the Space key or BkSp key. 2. A message is displayed. Press the Y, E, S, and Enter keys and the TPM information is erased. 3. The TPM setting changes from being displayed as Enable to Disabled, and the setting is no longer displayed.
HW Setup 7-12 User’s Manual
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ ■ ■ ■ PC card ExpressCard SD card Memory expansion Power devices ■ Battery pack ■ AC adaptor ■ Battery charger Peripheral devices ■ ■ ■ ■ ■ ■ ■ ■ Hard disk drive pack Slim Select Bay HDD adaptor USB floppy disk drive External monitor TV i.
Optional Devices PC card The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission. PC cards can sometimes become hot during PC operation.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not cause it to pop out sufficiently to allows it to be grasped. Be sure to push the PC card firmly into the computer and slide the eject button again. 4. Press the extended eject button to pop the card out slightly. 5.
Optional Devices To insert an ExpressCard, follow the steps below: 1. Insert an ExpressCard in the ExpressCard card slot. 2. Press gently to ensure a firm connection. ExpressCard slot ExpressCard Inserting an ExpressCard 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configuration in Windows to make sure it is appropriate for your ExpressCard. Removing an ExpressCard To remove the ExpressCard, follow the steps below. 1.
Optional Devices SD card The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants that use SD card flash-memory. The cards have a high level of security and copy protection features. The slot cannot accommodate Multi Media cards. Keep foreign objects out of the SD card slot.
Optional Devices ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost. Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the SD card and release it to pop the card out slightly. 4. Grasp the SD card and remove it.
Optional Devices ■ After using an SD card, return it to its case. ■ Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk Within the TOSHIBA SD Memory Boot Utility, a bootable SD memory card can be created if required. Refer to the Utilities of Chapter 1, Introduction for details. Memory expansion You can install additional memory in the computer’s memory module slot to increase the amount of RAM. This section describes how to install and remove a memory module.
Optional Devices Use a #0 point Phillips screwdriver to remove and fasten the screws. Use of an incorrect screwdriver can damage the screw heads. Installing memory module There are slots for two memory modules, one over the other. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the Turning off the power section in Chapter 3, Getting Started. 2.
Optional Devices Align the grooves along the edges of the memory module with the locking tabs on the connector and insert the module into the connector firmly. If you find it difficult to install the memory module, gently prize the locking tabs outwards using the tip of your finger. Ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in. ■ Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard.
Optional Devices 4. Loosen the screw securing the memory module cover. The screw is attached to the cover to prevent it from being lost. 5. Slide your fingernail or a thin object under the cover and lift it off. 6. Push the latches to the outside to release the module. A spring will force one end of the module up. 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot.
Optional Devices AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load. Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion).
Optional Devices 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector. Plastic tab Hard disk drive pack Removing the hard disk drive pack Installing the hard disk drive pack To install the hard disk drive pack, follow the steps below. 1. Move the connector until it is vertical. 2. Hold the hard disk drive vertically with its label on the left. 3. Connect the hard disk drive to the connector.
Optional Devices Slim Select Bay HDD adaptor You can increase your computer's data storage capacity by installing an additional hard disk drive in the Slim Select Bay. To install an hard disk drive in the Slim Select Bay HDD adaptor follow the steps below. 1. Slide the lock to the unlock position and open the lid. Lock Lid Opening the lid 2. Insert the hard disk drive in the Slim Select Bay HDD adaptor and push forward to ensure a firm connection.
Optional Devices 3. Close the lid and slide the lock to the lock position. Lid Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the computer’s Slim Select Bay slot, refer to Chapter 4, Operating Basics. USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics.
Optional Devices 3. Turn the monitor’s power on. 4. Turn the computer’s power on. When you turn on the power, the computer automatically recognizes the monitor and determines whether it is color or monochrome. However, the Windows Desktop appears on a display device that you used last time to shut down your computer, if the display device exists when you turn on the power. To change the display settings, press Fn + F5.
Optional Devices If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. c. Click the Settings tab and click the Advanced button. d. Click the Quadro NVS 110M tab, click Device Settings and click Select TV format. e. Select Advanced and select TV Settings in the TV Settings window. f.
Optional Devices Even if the above does not set up, there are some as which the movies is simultaneously displayed depending on the type of the movies. d. Click OK. e. Click OK in the Display Properties screen. i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Writable optical disc drives i.LINK uses a four-pin connector, which does not carry any electric current.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed.
Optional Devices Advanced Port Replicator III Plus In addition to the ports available on the computer, the Advanced Port Replicator III Plus provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator III Plus connects directly to the docking interface on the underside of the computer. The AC adaptor connects the Advanced Port Replicator III Plus to a power source. The computer must be configured properly before connecting to a LAN.
Optional Devices Serial devices The serial port can be used to connect to serial (RS-232C compatible) devices. RS-232C compatible devices include the following: ■ Modem ■ Mouse To connect a serial device, follow the steps below. 1. Turn the computer’s power off. 2. Connect the serial connector to the serial port and tighten the screws on the left and right hand side.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: S In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down and its DC IN indicator is flashing green Indicates a problem with the heat dispersal system. Please contact your dealer. AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information.
Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery or Slim Select Bay indicator does not glow orange.) If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes. If the battery still does not charge, make sure the outlet of the AC adaptor is supplying power. Test it by plugging in an appliance. Check whether the battery is hot or cold to the touch. If the battery is too hot or too cold, it will not charge properly.
Troubleshooting Real Time Clock Problem Procedure The following message is Displayed on the LCD screen: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The charge in the RTC battery has run out - you will need to set the date and time in the BIOS setup using the following steps: 1. Press F1 key. BIOS setup will boot up. 2. Set the date in System Date. 3. Set the time in System Time. 4. Press End key. Confirmation message will appear. 5. Press Y key.
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the The marks may have come from contact with the LCD screen. keyboard, Touch Pad or AccuPoint. Try wiping the LCD screen gently with a clean dry cloth.
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical disk drive icon in the task tray and turn on the power. Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware not configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD.
Troubleshooting Problem Procedure You cannot read a file Make sure the target file is on the SD memory card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer.
Troubleshooting Dual Pointing Device If you are using a USB mouse, also refer to the USB device section in this chapter and to your mouse documentation. Touch Pad/AccuPoint User’s Manual Problem Procedure Either the Touch Pad or the AccuPoint does not work. Check the Device Select settings. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. Open the Mouse Properties and click Dual Pointing Device tab.
Troubleshooting USB mouse Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2.
Troubleshooting USB device Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer.
Troubleshooting Problem Procedure Character display becomes garbled during a communication session In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol. You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. If problems persist, contact your dealer.
Troubleshooting Bluetooth For more information on Bluetooth wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card and Bluetooth SD card are installed in the computer.
Troubleshooting ■ Please be kind to our shared environment. Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly. This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government.
Chapter 10 Legal Footnotes This chapter states the Legal Footnote information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnote description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual. Clicking on *XX will display the related description. CPU Central Processing Unit (“CPU”) Performance Legal Footnote.
Legal Footnotes CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shut-down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium.
Legal Footnotes LCD Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Legal Footnotes 10-4 User’s Manual
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.37 kilograms, configured with: 14.1” XGA, 512MB RAM, 40GB HDD, DVD-ROM&CD-R/RW, Wireless LAN. Weight will vary with other configurations. Above weights are measured at specific criteria. They are not guaranteed as the maximum weight of the actual product. Size 315.6 (w) × 261.0 (d) × 31.2/34.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.
Specifications User’s Manual Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedance 600 ohms ±30% Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.
Specifications A-4 User’s Manual
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel. Two models are available: ■ 14.1" XGA, 1024 horizontal × 768 vertical pixels ■ 14.1" SXGA+, 1400 horizontal × 1050 vertical pixels Because of the LCD’s increased resolution, lines may appear broken in DOS mode.
Display Controller and Modes Table1 Video modes (VGA) Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) 0, 1 VGA Text 40 × 25 Characters 8×8 16 of 256K 70 2, 3 VGA Text 80 × 25 Characters 8×8 16 of 256K 70 0*, 1* VGA Text 40 × 25 Characters 8 × 14 16 of 256K 70 2*, 3* VGA Text 80 × 25 Characters 8 × 14 16 of 256K 70 0+, 1+ VGA Text 40 × 25 Characters 9 × 16 16 of 256K 70 2+, 3+ VGA Text 80 × 25 Characters 9 × 16 16 of 256K 70
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 70 11 VGA Grph 640 × 480 Pels 8 × 16 2 of 256K 60 12 VGA Grph 640 × 480 Pels 8 × 16 16 of 256K 60 13 VGA Grph 320 × 200 Pels 8×8 256 of
Display Controller and Modes Table 2 Video modes (XGA model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 (Virtual with LCD only) 256/256K 256/256K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 256/256K 256/256K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 256/256K 256/256K 60 75 85 2048 × 1536 (Virtual with LCD only) 256/25
Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 2048 × 1536 (Virtual with LCD only) 64K/64K
Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 100 1600 × 1200 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 100 1920 × 1440 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 2048 × 1536 (Virtual with LCD only) 16M/16M
Display Controller and Modes Table 3 Video modes (SXGA+ model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K 256/256K 60 75 85 100 1440 × 1050 256/256K 256/256K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 256/256K 256/256K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 256/256K 256/256K 60 75 85 2048 × 1536 (Virtu
Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K 64K/64K 60 75 85 100 1440 × 1050 64K/64K 64K/64K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 2048 × 1536 (Virtual w
Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M 16M/16M 60 75 85 100 1440 × 1050 16M/16M 16M/16M 60 75 85 100 1600 × 1200 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 100 1920 × 1440 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 2048 × 1536 (Virtual w
Display Controller and Modes PowerMizer PowerMizer is a graphics processor installed on this computer. The performance of PowerMizer can be configured in three ways.
Appendix C Wireless LAN Card Specifications Form Factor PCI-Ex MiniCard Type Compatibility ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance. Network Operating System ■ Microsoft Windows® Networking Media Access Protocol ■ CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) Data Rate ■ Theoretical maximum speed: 54Mbps (IEEE802.11a/IEEE802.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions. Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 2400-2483.
Wireless LAN Wireless IEEE 802.
Appendix D Bluetooth wireless technology Interoperability Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Bluetooth wireless technology Interoperability ■ Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth™ products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth™ Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability L‘utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
Bluetooth wireless technology Interoperability Caution: Exposure to Radio Frequency Radiation The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20cm.
Bluetooth wireless technology Interoperability Using Bluetooth™ Card from TOSHIBA equipment in Japan In Japan, the frequency bandwidth of 2,400 - 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on computer incorporating this product.
Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday Toll Free Tel Direct Dial FAX : : : : 10:00-17:00 0120-15-1048 03-3457-4850 03-3457-4868 Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law.
Bluetooth wireless technology Interoperability D-8 User’s Manual
Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A.
Appendix F TOSHIBA Anti-theft Protection Timer This function sets the limit for the number of days during which you are able to bypass authentication for the BIOS, Hard Disk Drive and Fingerprint. When the time limit is exceeded, you are required to provide the Password or fingerprint authentication for the BIOS and Hard Disk Drive to gain access to the system. To set permission and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility.
TOSHIBA Anti-theft Protection Timer F-2 User’s Manual
Appendix G If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office. Make a note of your computer’s machine type, model number, and serial number, and put it in a safe place.
If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output SXGA+: super extended graphics array plus TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus UXGA: ul
Glossary ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games.
Glossary byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
Glossary erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware.
Glossary I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it. IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit.
Glossary megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. mode: A method of operation, for example, the boot mode, Standby Mode or the Hibernation Mode.
Glossary output: The results of a computer operation. Output commonly indicates data. 1) printed on paper, 2) displayed at a terminal, 3) sent through the serial port of internal modem, or 4) stored on some magnetic media. P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1.
Glossary R Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use.
Glossary subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels independently, each may emit a different degree of brightness. See also pixel. synchronous: Having a constant time interval between successive bits, characters or events. system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file.
Glossary Glossary-14 User’s Manual
Index A AC adaptor, 1-4 additional, 1-16, 8-11 connecting, 3-6 Advanced Port Replicator III Plus, 1-17, 8-19 ASCII characters, 5-9 B Battery charging, 6-11 extending life, 6-14 indicator, 2-11, 6-3 location, 2-6 monitoring capacity, 6-12 real time clock, 1-4, 6-7 safety precautions, 6-8 save mode, 1-11 types, 6-5 Battery charger, 1-17, 8-11 Battery pack, 1-4, 2-7 additional, 8-10 replacing, 6-15 Bluetooth, 1-8, 4-33 Bluetooth Stack for Windows by Toshiba, 1-14 problems, 9-19 Boot Priority, 7-3 C Cleaning
Index E Environment, 3-1 Equipment checklist, 1-1 Equipment setup general conditions, 3-2 placement, 3-3 Ergonomics lighting, 3-5 seating and posture, 3-4 work habits, 3-5 ExpressCard, 1-7, 8-3 inserting, 8-3 location of slot, 2-2 problems, 9-12 removing, 8-4 External monitor, 1-7, 2-3, 8-14 problems, 9-16 F Fingerprint Sensor location, 2-8, 4-1 problems, 9-14 using, 4-3 Floppy disk care, 4-26 Fn + Ctrl (enhanced keyboard simulation), 5-3 Fn + Enter, 5-3 Fn + Esc (sound mute), 5-3 Fn + F1 (instant securit
Index I i.LINK, 1-7, 2-3, 8-17 connecting, 8-18 disconnecting, 8-18 precautions, 8-17 problems, 9-17 Indicators, 2-11, 6-3 K Keyboard, 1-7, 5-1 emulating enhanced keyboard, 5-2 Fn Sticky key, 5-6 Function keys F1...
Index mode), 3-10 standby mode, 3-10 system auto off, 6-20 turning off, 3-10 turning on, 3-9 Printer parallel, 7-8 Problems AC power, 9-5 AccuPoint, 9-13 Analyzing symptoms, 9-2 Battery, 9-5 Bluetooth, 9-19 Dual Pointing Device, 9-13 DVD Super Multi drive, 9-10 DVD-ROM&CD-R/RW drive, 9-9 ExpressCard, 9-12 External monitor, 9-16 Fingerprint sensor, 9-14 Hard disk drive, 9-8 Hardware and system checklist, 9-3 i.
Index Sound system, 4-27 headphone jack, 1-8, 2-4 microphone, 2-2 microphone jack, 1-8, 2-4 mute hot keys, 5-3 problems, 9-16 Stereo speakers, 2-9 volume control, 2-4 Standby, 1-12 setting, 3-10 System automatic, 1-10 T TOSHIBA Assist, 1-14 TOSHIBA Assist button, 1-10 TOSHIBA ConfigFree, 1-15 TOSHIBA Controls, 1-13 TOSHIBA Dual Pointing Device utility, 1-15 TOSHIBA Mic Effect, 1-15 TOSHIBA Mobile Extension, 1-15 TOSHIBA PC Diagnostic Tool, 1-14 TOSHIBA Power Saver, 1-12 TOSHIBA Presentation button, 1-10 T
Index Index-6 User’s Manual
