Cash Register User Manual

ManualsBrandsToshiba ManualsCash RegisterMA-600

PRINTED IN JAPAN

TEC Electronic Cash Register

MA-600 SERIES

Document No. EO3-11106

Original Dec., 2005

(Revised )

Programming Manual

Summary of content (191 pages)

PAGE 1
TEC Electronic Cash Register MA-600 SERIES Programming Manual Document No. EO3-11106 Original (Revised Dec.
PAGE 2
EO3-11106 TABLE OF CONTENTS Page 1. INTRODUCTION .........................................................................................................1- 1 1.1 1.2 Main Features ...............................................................................................................1- 1 Description of Model Number ........................................................................................1- 1 2. SPECIFICATIONS ........................................................................
PAGE 3
EO3-11106 Page 6.21 6.22 6.23 6.24 6.25 6.26 6.27 6.28 6.29 6.30 6.31 6.32 6.33 6.34 6.35 6.36 6.37 6.38 6.39 6.40 6.41 6.42 Department Listing Capacity (LC) Programming.........................................................6-106 Key Sticker Printing ....................................................................................................6-109 PLU Table Programming ............................................................................................
PAGE 4
1. INTRODUCTION EO3-11106 1.1 Main Features 1. INTRODUCTION This programming manual is provided for salespersons, field engineers, and other personal as supplementary manual for TOSHIBA TEC Electronic Cash Register MA-600 series. Reading through the MA-600 Owner’s Manual is recommended in order to thoroughly understand the descriptions in this manual. 1.1 Main Features • This ECR adopts an LCD display (192 x 64 dots), which displays a maximum of 24 one-byte characters by 4 lines.
PAGE 5
2. SPECIFICATIONS EO3-11106 2. SPECIFICATIONS 2. SPECIFICATIONS SIZE: 410 mm (width) x 442 mm (depth) x 291 mm (height) (height including rubber feet) Height when the customer display is fully raised: 351 mm WEIGHT: Approximately 13.6Kg POWER REQUIREMENT: AC 220 V to AC 230 V ±10 %; 50/60 Hz ±10 % (QP model) AC 230 V ±10 %; 50/60 Hz ±10 % (GB model) AC 240 V ±10 %; 50/60 Hz ±10 % (AU model) (varies depending on the destination) POWER CONSUMPTION: Standby: 8.2 W (0.08 A), Operating: 35 W (0.
PAGE 6
2. SPECIFICATIONS EO3-11106 2. SPECIFICATIONS PAPER ROLL (RECEIPT and JOURNAL) Media ---------------------------------------------------- Thermal roll paper Width ---------------------------------------------------- 58 +0/-1 mm Thickness----------------------------------------------- 0.060 mm to 0.
PAGE 7
3. CAPACITIES EO3-11106 3.1 Indexing Capacities 3. CAPACITIES 3.1 Indexing Capacities Input Item Digits Amount 7 Quantity in Multiplication 6 Unit Price in Multiplication 6 Tender Media Keys 8 Non-add Number Remarks 3 integer digits + 3 decimal digits (0.001 to 999.999) 18 Percent Rate 5 2 integer digits + 3 decimal digits (0.001 to 99.999%) VAT Rate 4 2 integer digits + 2 decimal digits (0.01 to 99.
PAGE 8
3. CAPACITIES EO3-11106 3.2 Basic Memory Capacities 3.2 Basic Memory Capacities (NOTE: For Item Count below, “6 + 2 digits” means that it has 6 integer digits and 2 decimal digits.) Group Memory (Group Name: 12 characters; max. 15 groups) Memory Type Counter or Total Item Count Daily Memory 6+2 Amount 10 Item Count Group Total Amount 6+2 10 Item Count GT Memory Digits 6+2 Amount 10 Item Count Group Total Amount 6+2 10 Department Memory (Department Name: 16 characters; max.
PAGE 9
3. CAPACITIES EO3-11106 3.3 Financial Memory 3.
PAGE 10
3. CAPACITIES EO3-11106 3.
PAGE 11
3. CAPACITIES EO3-11106 3.3 Financial Memory Financial Memory: (continued) Name of Total/Counter Daily Counter Type Counter Digits GT Total Digits Counter Digits Total Digits Remarks Credit-in-drawer Difference 10 at Money Declaration Misc.
PAGE 12
3. CAPACITIES EO3-11106 3.4 Cashier Memory 3.
PAGE 13
3. CAPACITIES EO3-11106 3.4 Cashier Memory Cashier Memory: (continued) Name of Total/Counter Daily Counter GT Type Counter Digits Total Digits Credit-in-drawer Credit-in-drawer (Foreign Currency 1) Credit-in-drawer (Foreign Currency 2) Credit-in-drawer (Foreign Currency 3) Credit-in-drawer (Foreign Currency 4) Credit-in-drawer (Foreign Currency 5) ENTRY 6 10 ENTRY 6 10 ENTRY 6 10 ENTRY 6 10 ENTRY 6 10 ENTRY 6 10 Misc. Media-in-drawer Misc.
PAGE 14
3. CAPACITIES EO3-11106 3.5 Others Cashier Memory: (continued) Name of Total/Counter Daily Counter GT Remarks Type Counter Digits Total Digits Counter Digits Total Digits Item Correct ENTRY 6 10 6 10 Item Correct on DP+/PLU+ Void ENTRY 6 10 6 10 Void on DP+/PLU+ Misc.
PAGE 15
3. CAPACITIES EO3-11106 3.6 Memory Balance 3.6 Memory Balance 1. GT (Grand Total) = Sum of Daily GS (Gross Sale) 2. NET GT = Sum of Daily Net Sales 3. NEG GT = GT – NET GT 4. GS (Gross Sale) = (Sum of Positive Depts) + (Sum of Add-on Taxes) NOTE 1 5.
PAGE 16
4. SYSTEM START-UP PROCEDURE EO3-11106 4. SYSTEM START-UP PROCEDURE 4. SYSTEM START-UP PROCEDURE Case 1: To start-up using the MA-600 terminal only RAM Clear (Chapter 5) All the programming operations required for the terminal (Chapter 6) Case 2: To start-up by installing programming data from the PC CAUTION! < Precautions for connection to PC > 1. The USB cable should be connected to the ECR each time a PC sends/receives data to/from the ECR.
PAGE 17
4. SYSTEM START-UP PROCEDURE EO3-11106 4. SYSTEM START-UP PROCEDURE PC Transmission Information Setting Data transmission information setting with a PC connection is performed here. CONDITION Any time outside a sale OPERATION Mode Lock: BLIND 68 [X] 1 [ST] | POL Watch Timer | [#] Max. 2 digits: 0 to 99 (Standard: 20 sec.) 2 [ST] | Response Watch Timer | [#] Max. 2 digits: 0 to 99 (Standard: 20 sec.) 3 [ST] | Transmission Delay Timer | [#] Max.
PAGE 18
5. RAM CLEAR, DATA CLEAR, STATUS CLEAR EO3-11106 5.1 RAM Clear 5. RAM CLEAR, DATA CLEAR, STATUS CLEAR 5.1 RAM Clear CAUTION! This clear operation deletes all programmed data and sales data stored in the memory of the ECR. (i.e., the ECR goes back to initial status.) If the ECR becomes completely inoperative due to battery discharge or malfunction of the program memory, the RAM Clear operation must be carried out. When the RAM Clear is operated, all memory stored in the RAM will be cleared. (i.e.
PAGE 19
5. RAM CLEAR, DATA CLEAR, STATUS CLEAR EO3-11106 5.2 DATA Clear 5.2 DATA Clear CAUTION! This clear operation deletes all sales data of any operation sequence stored in the memory of the ECR. Performing the DATA Clear operation will clear only the sales data accumulated in the memory of the ECR (report memory), however, the programmed data will not be cleared. By this operation, all sales data including non-resettable totals and counters, Reset Report Counts, and Receipt Consecutive No. are cleared. 1.
PAGE 20
5. RAM CLEAR, DATA CLEAR, STATUS CLEAR EO3-11106 5.3 STATUS Clear 5.3 STATUS Clear Performing the STATUS Clear operation will clear an error and the key locked condition, however, the sales data and the programmed data will not be cleared by this operation. When the STATUS Clear is operated to clear a key locked condition during sale, the sale item data that has already been entered for the current sale will be cleared.
PAGE 21
6. TERMINAL FILE PROGRAMMING EO3-11106 6. TERMINAL FILE PROGRAMMING 6.
PAGE 22
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6.1 Instructions for Programming On the MA-600 series adopting the LCD display, each programming operation is performed by selecting the corresponding menu item on the LCD display. The keyboard layout is automatically switched among three according to operation to be performed (ordinary registration, read/reset, programming) when the Mode Lock is turned to the corresponding position.
PAGE 23
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6.1.2 Keyboard Layout Variations The keyboard layout is automatically switched among three according to operation to be performed (ordinary registration, read/reset, programming) when the Mode Lock is turned to the corresponding position. In this chapter, various programming operations are performed with the keyboard layout for programming. (1) Keyboard layout for ordinary registration (It is programmed as default setting.
PAGE 24
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming (2) Keyboard layout for programming SET Mode Lock Position: BLIND • Ordinary Type Keyboard ↑ Del ↓ ALL VOID ← Rtn 7 → Dbl Enter A/a RF JF A F K P U # B G L Q V 8 9 C H M R W 4 5 6 D I N S X 1 2 3 E J O T Y 0 00 .
PAGE 25
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming (3) Keyboard layout for Read/Reset X Mode Lock Position: Z • Ordinary Type Keyboard ↑ RF ↓ C JF # ← Rtn 7 8 9 → X 4 5 6 1 2 3 0 00 . Enter PLU ST AT/TL • Flat Type Keyboard RF # X JF C ↑ ↓ ← → Rtn Enter 7 8 9 4 5 6 1 2 3 ST 0 00 .
PAGE 26
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6.1.2 1. Basic Key Functions The following are main keys and their functions to be used in programming operations. (1) Keys for selecting items on the menu screen Key [↑] [↓] [←] [→] [Enter] [Rtn] [?] Function This key is used for moving the cursor upward. This key is used for moving the cursor downward. This key is used for moving the cursor leftward. This key is used for moving the cursor rightward.
PAGE 27
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 3. To clarify the operation flow, definitions of keys of the ECR keyboard are as shown below. | | --------- Selective numeric value which is entered through the Numeric keys. [ ]---------- Depression of the function key. xxxx------------- Fixed numeric value which is entered through the Numeric keys. Fixed 4. Table of key names in SET and REG modes The keyboard layout for programming is adopted in SET mode.
PAGE 28
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6.2.
PAGE 29
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries Character Setting Operations • To set a one-byte character, enter the COL (column) code and then the ROW code, followed by the [#] key. ex.) To set “%”, enter 205 and depress the [#] key. To set “kg”, enter1508 and depress the [#] key. • To set a space instead of a character, simply depress the [#] key without a prior entry, or enter 200 and depress the [#] key.
PAGE 30
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6.2.2 Direct Character Entry Method Using Keyboard (installed as the ECR Main Keyboard): -- Keyboard layout for programming -• Ordinary Type Keyboard ↑ Del ↓ ALL VOID ← Rtn 7 → Dbl Enter A/a RF JF A F K P U # B G L Q V 8 9 C H M R W 4 5 6 D I N S X 1 2 3 E J O T Y 0 00 .
PAGE 31
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries Using PK-2 (PLU Keyboard; hardware option) The PK-2 keyboard is used for entering a required PLU code by simply depressing the code-preset key on this keyboard in REG or MGR mode. In addition, the PK-2 can be used for directly entering characters during the programming operations that require character settings such as STORE NAME/MESSAGE AND COMMERCIAL MESSAGE PROGRAMMING and DEPARTMENT NAME PROGRAMMING.
PAGE 32
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6.2.3 How to use the [History] key The [History] key is used for performing character entries with the name previously entered. Operation: [History] ([↓]) [Enter] 1) The [History] key depression will let the most recently programmed name displayed on the LCD display. 2) The [↓] key depression will let the second most recently programmed name displayed. (Up to 10 programmed names will be displayed in reverse chronological order.
PAGE 33
6. TERMINAL FILE PROGRAMMING EO3-11106 6.3 Condition Required for Programming Operations 6.3 Condition Required for Programming Operations “CONDITION” is given at the top of each programming operation. The ECR must satisfy this condition to perform programming operations. There are two types of conditions: “Any time outside a sale” It means that the programming operation is allowed when a sale is finalized before going into any other sale entry.
PAGE 34
6. TERMINAL FILE PROGRAMMING EO3-11106 6.4 SFKC (Selective Function Key Code) Programming 6.4 SFKC (Selective Function Key Code) Programming SFKC Programming is to determine the keyboard layout with the required keys. This operation must be performed first before any other programming operation. If the RAM Clear is performed prior to the SFKC programming, program only the keys that require changes from the SFKC in the Standard Keyboard which has been set by the RAM Clear operation automatically.
PAGE 35
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 36
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 37
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 38
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6.5 System Option Programming This operation is used to set the ECR’s basic features and selective functions to meet the requirement of the market and your user. This programming operation is performed in SET mode or BLIND mode. In SET mode, you can select a desired menu item on the LCD display. Address No. 1 to Address No. 29 are programmable. In BLIND mode, you can directly enter a desired Address No. on the keyboard.
PAGE 39
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming Setting Example) To set Address No. 1 with the following requirements: (Refer to the Address No. 1 table on the subsequent page.) Bit No. 1: Time NON-PRINT (SET status) Bit No. 3: Subtotal NON-PRINT (SET status) Other bits will be selected to “RESET” status. Operation LCD Display Remarks The cursor is moved on to “6 OTHER”. When the ECR is being outside a sale and in SET mode, depress the [↓] key five times.
PAGE 40
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming (continued from the previous page) Operation LCD Display Remarks The status of Bit No.1 is turned from N to Y. N: RESET status Y: SET status Depress the [→] key to select the status of Bit No. 1. The numeric value 1 indicating the Bit No. with SET status is displayed on the 7segment Numeric display. Depress the [↓] key twice to move the cursor on to Bit No. 3 (B3ST). The status of Bit No.3 is turned from N to Y.
PAGE 41
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming Setting Example) To set Address No. 1 with the following requirements: (Refer to the Address No. 1 table on the next page.) Bit No. 1: Time NON-PRINT (SET status) Bit No. 3: Subtotal NON-PRINT (SET status) Other bits will be selected to “RESET” status. Key Operation: Mode Lock: BLIND, enter 18, depress [X]. 1 [ST] Address No. 13 [#] Bit Nos. for SET [AT/TL] To complete this setting.
PAGE 42
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 1 NON-PRINT OPTION I BIT NO.
PAGE 43
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 2 NON-PRINT OPTION II BIT NO.
PAGE 44
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 3 OPTIONAL FUNCTION I BIT NO.
PAGE 45
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 4 OPTIONAL FUNCTION II BIT NO. 1 2 3 4 ITEM Zero-skip in All Department and Department Group Reports Zero-skip in PLU Reports Zero-skip on Financial and Cashier Reports Cashier feature SELECTIVE STATUS RESET SET RESET SET RESET SET RESET SET 5 6 Cashier No.
PAGE 46
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 6 REMOTE SLIP PRINTER CONTROL BIT NO.
PAGE 47
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 7 OPTIONAL FUNCTION III BIT NO.
PAGE 48
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 11 NON-PRINT OPTION III BIT NO.
PAGE 49
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 17 OPTIONAL FUNCTION IV BIT NO.
PAGE 50
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 19 CONSIGNMENT OPTION BIT NO. 1 2 ITEM Single-Consignment or Multi-Consignment Date Print SELECTIVE STATUS RESET SET RESET SET 3 Consecutive No.
PAGE 51
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 20 TAX CONTROL I BIT NO.
PAGE 52
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 21 TAX CONTROL II BIT NO.
PAGE 53
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 22 TAX CONTROL III BIT NO.
PAGE 54
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 27 DRAWER OPTION BIT NO. 1 2 ITEM Drawer Close Compulsory Drawer Warning Alarm SELECTIVE STATUS RESET SET RESET SET 3 4 Single-drawer or Multidrawer Multi-drawer Control RESET SET RESET SET 5 6 7 Selection of Change at Tendering in Foreign Currencies Number of Drawers (if Multi-drawer spec.
PAGE 55
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 28 OPTIONAL FUNCTION VI BIT NO. 1 2 3 4 5 6 7 8 ITEM No-sale Entry After Non-add # Entry Number of Times for Non-add # Entries Within a Receipt [RF] Operation During a Sale Consecutive No. on Receipt and Journal Consecutive No.
PAGE 56
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 29 OPTIONAL FUNCTION VII BIT NO.
PAGE 57
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 30 OPTIONAL FUNCTION VIII BIT NO.
PAGE 58
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 31 OPTIONAL FUNCTION IX BIT NO. ITEM 1 -- vacant -- SELECTIVE STATUS 0 STANDARD STATUS REMARKS * RESET SET 2 -- vacant -- * RESET SET 3 Date, day of week, and Register No.
PAGE 59
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 32 OPTIONAL FUNCTION X BIT NO.
PAGE 60
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 33 OPTIONAL FUNCTION XI BIT NO.
PAGE 61
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 34 OPTIONAL FUNCTION XII BIT NO. 1 2 3 4 ITEM Decimal Point in Item Count and % Rate Amount Division Symbol between Main and Subsidiary digits for 0.00 type Amount Division Symbol between 3rd and 4th digits for . - - 0 -- vacant -- SELECTIVE STATUS RESET SET RESET SET RESET SET . , . , . , 12 STANDARD STATUS -- ex) 1.
PAGE 62
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 36 FOREIGN CURRENCY OPTION BIT NO.
PAGE 63
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 37 OPTIONAL FUNCTION XIII BIT NO.
PAGE 64
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 38 OPTIONAL FUNCTION XIV BIT NO.
PAGE 65
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 39 OPTIONAL FUNCTION XV BIT NO.
PAGE 66
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 42 OPTIONAL FUNCTION XVI BIT NO. ITEM 1 -- vacant -- SELECTIVE STATUS 0 STANDARD STATUS REMARKS * RESET SET 2 -- vacant -- * RESET SET 3 -- vacant -- * RESET SET 4 -- vacant -- * RESET SET 5 -- vacant -- * RESET SET 6 -- vacant -- * RESET SET 7 -- vacant -- * RESET SET 8 NOTE: Consecutive No.
PAGE 67
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 47 PC OPTION BIT NO.
PAGE 68
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 49 OPTIONAL FUNCTION XVII BIT NO.
PAGE 69
6. TERMINAL FILE PROGRAMMING EO3-11106 6.6 Commercial Message Programming 6.6 Commercial Message Programming A maximum of 96 characters of Commercial Message (32 characters x 3 lines) to be printed on the receipt is programmed here. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu * Depress [1] or [Enter]. “1 MESSAGES” for various message programming is selected. Depress [1] or [Enter]. “1 COMMERCIAL MESSAGE” is selected.
PAGE 70
6. TERMINAL FILE PROGRAMMING EO3-11106 6.6 Commercial Message Programming 3) Example: To program the following Commercial Message. O p e n C l o s e d : 8 : 0 0 a m e v e r y t o 7 : 0 0 p m W e d n e s d a y Line No. 1 Line No. 2 Line No. 3 Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [1] or [Enter] key. Depress the [1] or [Enter] key.
PAGE 71
6. TERMINAL FILE PROGRAMMING EO3-11106 6.6 Commercial Message Programming (continued from the previous page) Operation LCD Display Remarks The [Enter] key depression results in that the input message is entered and displayed. When the [Enter] key is depressed, the message programmed in the 2nd line is printed. The [Enter] key depression allows the ECR to enter the 3rd line message input mode. (The [C] key depression clears the message already programmed.) The 3rd line message is input.
PAGE 72
6. TERMINAL FILE PROGRAMMING EO3-11106 6.7 Footer Message Programming 6.7 Footer Message Programming A maximum of 64 characters of Footer Message (32 characters x 2 lines) to be printed on the receipt is programmed here. Prior to the Footer Message Programming, be sure to select RESET status for Address No. 29, Bit No. 6 of the system option. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu Depress [1] or [Enter].
PAGE 73
6. TERMINAL FILE PROGRAMMING EO3-11106 6.7 Footer Message Programming 3) Example: To program the following Footer Message. T h a n k y o u Line No. 1 C a l Operation l a g a i n LCD Display Line No. 2 Remarks When the ECR is being outside a sale and in SET mode, depress the [1] or [Enter] key. The cursor is moved on to “2 FOOTER MESSAGE”. Depress the [↓] key. Depress the [2] or [Enter] key. The message already programmed is displayed.
PAGE 74
6. TERMINAL FILE PROGRAMMING EO3-11106 6.7 Footer Message Programming (continued from the previous page) Operation LCD Display Remarks Numbers of programmed characters and of programmable characters are displayed on the 7-segment numeric display. The [Enter] key depression allows the ECR to enter the 2nd line message input mode. (The [C] key depression clears the message already programmed.) The 2nd line message is input.
PAGE 75
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming 6.8 Store Name Message Programming A maximum of 128 characters of Store Name Message (32 characters x 4 lines) to be printed on the receipt is programmed here. Prior to the Store Name Message Programming, be sure to select SET status for Address No. 31, Bit No. 5 of the system option. CONDITION OPERATION Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu Depress [1] or [Enter].
PAGE 76
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming NOTES: 1. 2. 3. 4. For each line, a maximum of 32 one-byte characters or 16 two-byte characters can be entered. A combination of both types is also available. When blanks are entered for the whole one line, it results in one line feed. When the store name message specification has been selected, the 4-line range assigned for the store name message is either printed or fed, regardless of any system option selection.
PAGE 77
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming 3) Example: To program the following Store Message. T E C 1 3 4 3 S T P E A C H P H O N E : O R E D R I V E 8 7 - 6 4 3 7 Line No. 1 Line No. 2 Line No. 3 Line No. 4 Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [1] or [Enter] key. The cursor is moved on to “3 STORE MESSAGE”. Depress the [↓] key twice. Depress the [3] or [Enter] key.
PAGE 78
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming (continued from the previous page) Operation LCD Display Remarks When the [Enter] key is depressed, the message programmed in the 2nd line is printed. The [Enter] key depression results in that the input message is entered and displayed.
PAGE 79
6. TERMINAL FILE PROGRAMMING EO3-11106 6.9 Department Name Programming 6.9 Department Name Programming A maximum of 16 characters of department name is programmed here. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter]. or Depress [2]. “2 NAMES” for various name programming is selected. Depress [2] or [Enter] key. “1 DP KEY NAME” is selected.
PAGE 80
6. TERMINAL FILE PROGRAMMING EO3-11106 6.9 Department Name Programming 3) Example To program “FOOD” as the name of Department 01. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key. The cursor is moved on to “2 NAMES”. Depress the [2] or [Enter] key. “2 NAME” is selected. Depress the [1] or [Enter] key. “1 DP KEY NAME” is selected. Depress the [Enter] key.
PAGE 81
6. TERMINAL FILE PROGRAMMING EO3-11106 6.10 Department Group Name Programming 6.10 Department Group Name Programming In this operation, the name of each Department Group is programmed. Which Departments are linked to each Group has been set in the DEPARTMENT TABLE PROGRAMMING operation. A maximum of 15 department groups can be set. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
PAGE 82
6. TERMINAL FILE PROGRAMMING EO3-11106 6.10 Department Group Name Programming (continued from the previous page) Operation LCD Display Remarks Depress the [2] or [Enter] key. “2 NAMES” is selected. Depress the [↓] key. The cursor is moved on to “2 DP GROUP NAME”. Depress the [2] or [Enter] key. “2 DP GROUP NAME” is selected. Depress the [Enter] key. When programming a name of another department group, move the cursor on to a desired one with the [↓] or [↑] key, then depress the [Enter] key.
PAGE 83
6. TERMINAL FILE PROGRAMMING EO3-11106 6.11 Cashier Name and Status Programming 6.11 Cashier Name and Status Programming Cashier Name and Cashier Status for each cashier can be programmed here. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu Depress [↓] then [Enter]. or Depress [2]. Depress [↓] twice then [Enter]. or Depress [3]. Select a cashier to be programmed with the [↑] or [↓] key, then depress [Enter]. [Enter] Input a cashier name.
PAGE 84
6. TERMINAL FILE PROGRAMMING EO3-11106 6.11 Cashier Name and Status Programming NOTES: 1. Cashiers 1 to 8 are programmed with the names “1CL” to “8CL” as default setting. 2. For the name of each cashier, a maximum of 12 one-byte or 6 two-byte characters can be entered. A combination of both types is also available. 3. Training entry status is available for every cashier. 4.
PAGE 85
6. TERMINAL FILE PROGRAMMING EO3-11106 6.11 Cashier Name and Status Programming (continued from the previous page) Operation LCD Display Remarks Numbers of programmed characters and of programmable characters are displayed on the 7-segment numeric display. The [Enter] key depression allows the ECR to enter the cashier 1 name input mode. (The [C] key depression clears the name already programmed.) The cashier 1 name is input.
PAGE 86
6. TERMINAL FILE PROGRAMMING EO3-11106 6.12 PLU Name Programming 6.12 PLU Name Programming A maximum of 16 characters of PLU name is programmed here. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter]. or Depress [2]. “2 NAMES” for various name programming is selected. Depress the [↓] key three times then [Enter]. or Depress [4]. “4 PLU (ITEM NO.) NAME” is selected.
PAGE 87
6. TERMINAL FILE PROGRAMMING EO3-11106 6.12 PLU Name Programming (continued from the previous page) Operation LCD Display Remarks Depress the [2] or [Enter] key. Depress the [↓] key three times. The cursor is moved on to “4 PLU (ITM NO.) NAME”. Depress the [4] or [Enter] key. “4 PLU (ITM NO.) NAME” is selected. Depress the [Enter] key. When programming a name of another PLU, move the cursor on to a desired PLU with the [↓] or [↑] key, then depress the [Enter] key. (PLU Code No. 0001 is selected.
PAGE 88
6. TERMINAL FILE PROGRAMMING EO3-11106 6.13 Salesperson Name Programming 6.13 Salesperson Name Programming By programming Salesperson here, the name of each salesperson can be programmed in a maximum of 12 characters. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter]. or Depress [2]. “2 NAMES” is selected. Depress the [↓] key four times then [Enter] key. or Depress [5].
PAGE 89
6. TERMINAL FILE PROGRAMMING EO3-11106 6.13 Salesperson Name Programming 3) Example To program “White” on Salesperson Code 01: Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key. The cursor is moved on to “2 NAMES”. Depress the [2] or [Enter] key. “2 NAMES” is selected. Depress the [↓] key four times. The cursor is moved on to ”5 SALESPERSON NAME”. Depress the [5] or [Enter] key. ”5 SALESPERSON NAME” is selected. Depress the [Enter] key.
PAGE 90
6. TERMINAL FILE PROGRAMMING EO3-11106 6.13 Salesperson Name Programming (continued from the previous page) Operation LCD Display Remarks A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this programming.
PAGE 91
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 6.14 Financial Report Item Name Programming Item Names printed on Financial Report are programmed here. Many of them are also printed on sales receipts. Other Line Item Names will be programmed in 6.15 Print Line Item Name Programming. CONDITION OPERATION After Financial Reset Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter].
PAGE 92
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 3) Example To program “NET GT” instead of “NET GT” for Item Code 2 (NET GT) all in double-sized characters. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key. The cursor is moved on to “2 NAMES”. Depress the [2] or [Enter] key. “2 NAMES” is selected. Depress the [↓] key five times. The cursor is moved on to ”6 FINANCIAL ITM NAME”.
PAGE 93
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming (continued from the previous page) Operation LCD Display Remarks A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this programming.
PAGE 94
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 95
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 96
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 97
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 6.15 Print Line Item Name Programming Print Line Item Names not listed in Section 6.14 Financial Report Item Name Programming can be programmed here. CONDITION Anytime outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter]. or Depress [2]. “2 NAMES” is selected. Depress the [↓] key six times then [Enter] key.
PAGE 98
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 3) Example To program the amount mark “€” in Item Code 7: (The amount mark has not been preset as the standard program data). Meanwhile, the names of the other items in the Item Code 7 should remain unchanged as the standard program data (i.e. “@” for Unit Price Symbol and “ITEM” for Sale Item Count Symbol). Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key.
PAGE 99
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming (continued from the previous page) Operation LCD Display Remarks A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this programming. TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 31-10-2005 MON #0 PRINT NAME #007 @€ITEM 0012 13:29TM Print Line Item Name Table Max.
PAGE 100
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming Print Line Item Name Table (continued) Max.
PAGE 101
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming Print Line Item Name Table (continued) Max.
PAGE 102
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming NOTES: 1. The standard program data for the Amount Mark in Item Code 7 is set with a blank after a RAM Clear. When the specific Amount Mark for the domestic currency is required on sales receipts (such as £, ¥, $), you must program the entire contents of Item Code 7. 2. The Cashier Symbol to be set in Item Code 8 (“CL” in Standard Program) will be used to print the 2-digit Cashier ID code on a validation slip.
PAGE 103
6. TERMINAL FILE PROGRAMMING EO3-11106 6.16 Display item Name Programming 6.16 Display Item Name Programming Display Item Name to be displayed on the LCD display can be programmed here. (Max. 16 characters) CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter]. or Depress [2]. “2 NAMES” is selected. Depress the [↓] key seven times then [Enter] key. or Depress [8].
PAGE 104
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 105
6. TERMINAL FILE PROGRAMMING EO3-11106 6.16 Display item Name Programming 3) Example To program “BALANCE DUE” instead of standard program data “TOTAL” for Item Code 3. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key. The cursor is moved on to “2 NAMES”. Depress the [2] or [Enter] key. “2 NAMES” is selected. Depress the [↓] key seven times. The cursor is moved on to ”8 DISPLAY ITEM NAME”. Depress the [8] or [Enter] key.
PAGE 106
6. TERMINAL FILE PROGRAMMING EO3-11106 6.16 Display item Name Programming (continued from the previous page) Operation LCD Display Remarks A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this programming.
PAGE 107
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 6.17 Error Item Name Programming Error item names to be displayed on the LCD display are programmed here. A maximum of 16 one-byte characters by 2 lines can be programmed. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter]. or Depress [2]. “2 NAMES” is selected.
PAGE 108
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 3) Example To program “CALL MANAGER” instead of standard program data “MANAGER REQUIRED” for Error Code 3. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key. The cursor is moved on to “2 NAMES”. Depress the [2] or [Enter] key. “2 NAMES” is selected. Depress the [↓] key eight times. The cursor is moved on to ”9 ERROR ITEM NAME”. Depress the [9] or [Enter] key.
PAGE 109
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming (continued from the previous page) Operation LCD Display Remarks A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this programming.
PAGE 110
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 111
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 112
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming Error Code and Error Item Name Table (continued) Error Code 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 to 200 Content or Cause of Error Standard Program -- vacant --- vacant --- vacant --- vacant -Price Input Prohibition Error No price is input.
PAGE 113
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming 6.18 Read/Reset Report Name Programming Read/Reset Report Names are programmed here. A maximum of 12 one-byte characters can be programmed. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] then [Enter]. or Depress [2]. “2 NAMES” is selected. Depress the [↓] key nine times then [Enter] key.
PAGE 114
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming 3) Example To program “X_DP_PROFIT” instead of standard program data “X_PROFIT” for Report No. 21. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key. The cursor is moved on to “2 NAMES”. Depress the [2] or [Enter] key. “2 NAMES” is selected. Depress the [↓] key nine times. The cursor is moved on to ”0 X/Z REPORT NAME”. Depress the [0] or [Enter] key.
PAGE 115
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming (continued from the previous page) Operation LCD Display Remarks A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this programming. TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 31-10-2005 MON #0 REPORT NAME #21 X_DP_PROFIT 0015 13:35TM Read/Reset Report Name Table X: Z: GTX: GTZ: Report No.
PAGE 116
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming Read/Reset Report Name Table (continued) X: Z: GTX: GTZ: Report No.
PAGE 117
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming Read/Reset Report Name Table (continued) X: Z: GTX: GTZ: Report No.
PAGE 118
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming 6.19 Department Table Programming For each department, memory opening, and department various statuses settings are performed here.
PAGE 119
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming *1: Department Group No. • Input a department group code (2 digits: 01 to 15), then depress the [Enter] key. • To cancel a department group, input 0 then depress the [Enter] key. • All departments can be programmed in a group. Negative departments are added to the group total. *2: Preset Price • For a preset department (preset-price department), enter a maximum of 6-digit price, and depress the [Enter] key.
PAGE 120
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming *5: High Amount Limit • Enter a maximum of 7 digits to be set as the high amount to be locked out. Example) To prohibit any amount equal to or larger than 40,00: 4000 [Enter] (Allows any amount equal to or smaller than 39,99.) NOTES: 1. To cancel the preset limit (i.e. to allow any amount), input 0. 2. The limit amount set here will be applied to entries in REG mode only, but not in MGR or - mode. 3.
PAGE 121
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming (continued from the previous page) Operation LCD Display Remarks Depress the [3] or [Enter] key. “3 DP/PLU” is selected. Depress the [1] or [Enter] key. “1 DP” is selected. Depress the [1] or [Enter] key. “1 DP SETTINGS” is selected. Depress the [Enter] key to select Department 01. The [?] key depression results in that the following guidance message appears on the LCD display.
PAGE 122
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming (continued from the previous page) Operation LCD Display Remarks Move the cursor on to a desired status setting with the [↓] or [↑] key. The [?] key depression results in that the following guidance message appears on the LCD display. Depress the [→] key then the [Enter] key. The [→] key depression results in that the status is changed from N to Y. (The status of SINGLE-ITEM DP is selected.
PAGE 123
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming (continued from the previous page) Operation LCD Display Remarks Depress the [Rtn] key. The display returns to the Department Setting screen. Move the cursor on to another desired department with the [↓] or [↑] key, then depress the [Enter] key. A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this programming.
PAGE 124
6. TERMINAL FILE PROGRAMMING EO3-11106 6.20 Department Preset Price Setting or Changing 6.20 Department Preset Price Setting or Changing The preset price of each department may be set in the DEPARTMENT TABLE PROGRAMMING already described. However, in setting or changing the price only but not other programmed data, the following operation will be more convenient.
PAGE 125
6. TERMINAL FILE PROGRAMMING EO3-11106 6.20 Department Preset Price Setting or Changing (continued from the previous page) Operation LCD Display Remarks Depress the [3] or [Enter] key. “3 DP/PLU” is selected. Depress the [1] or [Enter] key. “1 DP” is selected. Depress the [↓] key. The cursor is moved on to “2 UNIT PRICE”. Depress the [2] or [Enter] key. “2 UNIT PRICE” is selected. Input 100 for the preset price of Department 1 (FOOD).
PAGE 126
6. TERMINAL FILE PROGRAMMING EO3-11106 6.21 Department Listing Capacity (LC) Programming 6.21 Department Listing Capacity (LC) Programming The High Amount to be Locked Out (HALO) and Low Amount to be Locked Out (LALO) relating to the department entry are programmed here. Entry of an amount larger than HALO or smaller than LALO can be prohibited. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
PAGE 127
6. TERMINAL FILE PROGRAMMING EO3-11106 6.21 Department Listing Capacity (LC) Programming 2. 3. 3) • The HALO and LALO programmed here are effective at the department entry in REG mode only. They are not effective in MGR and - mode, as a maximum of 7-digit amount value can be entered. • Zeros must be entered as all the digits other than the highest digit. If any other value is entered, it will be regarded as a zero. Example) Entering 4001 to 4999 will all result in setting 4000.
PAGE 128
6. TERMINAL FILE PROGRAMMING EO3-11106 6.21 Department Listing Capacity (LC) Programming (continued from the previous page) Operation LCD Display Input 10, then depress the [Enter] key. Remarks When the [Enter] key is depressed, the programmed data is printed. (LALO: 10) The [End] key depression allows the ECR to end this programming. A long receipt is issued and the display returns to Main Menu screen.
PAGE 129
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing 6.22 Key Sticker Printing Key stickers of department names which were programmed in the DEPARTMENT NAME PROGRAMMING can be printed on the receipt printer. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart • For printing all department names Main Menu ECR is being outside a sale and in SET mode. Depress [↓] twice then [Enter]. or Depress [3].
PAGE 130
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing NOTES: 1. Print format < Single key > • For the single key, a maximum of 12-digit department name (6 characters x 2 lines) can be printed. • For a 7-digit-or-more department name, the first 6 digits are printed in the first line and the 7th digit and after are printed in the second line. • The 6-digit-or-less department name is printed in the second line. • For a 13-digit-or-more department name, the first 12 digits are printed.
PAGE 131
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing (continued from the previous page) Operation LCD Display Depress the [1] or [Enter] key. Remarks ”1 ALL DP” is selected. A confirmation message is displayed. The [End] key depression allows the ECR to end this operation. A long receipt is issued and the display returns to Main Menu screen.
PAGE 132
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing (2) To print part of department names. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key twice. The cursor is moved on to “3 DP/PLU”. Depress the [3] or [Enter] key. “3 DP/PLU” is selected. Depress the [1] or [Enter] key. ”1 DP” is selected. Depress the [↓] key three times. The cursor is moved on to “4 KEY STICKER PRINT”. Depress the [4] or [Enter] key.
PAGE 133
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6.23 PLU Table Programming This programming can be operated when new PLU items are to be added, PLU program data is to be changed, or PLUs are to be deleted. 6.23.1 Programming or Changing CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] twice then [Enter]. or Depress [3].
PAGE 134
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming NOTES: 1. A maximum of 1,000 PLUs are programmable. 2 If a PLU is linked to a negative department, the PLU is automatically set as negative PLU. 3. The [PLU] key here indicates the key labelled simply as “PLU” but not any PLU preset-code keys. *1: Linked Department Code • Enter a 2-digit code of the department to which the PLU is linked.
PAGE 135
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 3) Example To program the following PLU data: PLU Code: Linked Department: Preset Price: 2nd Preset Price: 3rd Preset Price: Tax Status: Operation 0010 Department 1 €1,00 €1,20 €1,50 12 (VAT 1 and VAT 2) LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key twice. The cursor is moved on to “3 DP/PLU”. Depress the [3] or [Enter] key. “3 DP/PLU” is selected. Depress the [↓] key.
PAGE 136
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming (continued from the previous page) Operation LCD Display Remarks The [?] key depression results in that the following guidance message appears on the LCD display. Input 100, then depress the [Enter] key. (Preset Price €1,00 is set.) The [?] key depression results in that the following guidance message appears on the LCD display. Input 120, then depress the [Enter] key. (2nd Preset Price €1,20 is set.
PAGE 137
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6.23.2 Deletion CONDITION To delete a PLU with sales data of zero: Any time outside a sale To delete a PLU with sales data of not zero: After PLU Reset OPERATION Mode Lock: SET Individual PLU Deletion: 1) Menu Tree 2) Operation Flowchart The programmed PLU data is deleted individually. Main Menu ECR is being outside a sale and in SET mode. Depress [↓] twice then [Enter]. or Depress [3].
PAGE 138
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming (continued from the previous page) Operation LCD Display Remarks Depress the [↓] key. Depress the [1] or [Enter] key. “2 PLU” is selected. Depress the [↓] key three times. The cursor is moved on to “4 DELETE (INDIV)”. Depress the [4] or [Enter] key. “4 DELETE (INDIV)” is selected. Input 0501 (or 501), then depress the [PLU] key. PLU Code: Max. 4 digits (1 to 9999) (PLU Code 0501 is specified.
PAGE 139
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming All PLU Deletion: 1) Menu Tree 2) Operation The programmed PLU data is deleted entirely. Operation LCD Display Remarks The cursor is moved on to “3 DP/PLU”. When the ECR is being outside a sale and in SET mode, depress the [↓] key twice. Depress the [3] or [Enter] key. Depress the [↓] key. Depress the [2] or [Enter] key. “2 PLU” is selected. Depress the [↓] key four times. The cursor is moved on to “5 DELETE (ALL)”.
PAGE 140
6. TERMINAL FILE PROGRAMMING EO3-11106 6.24 PLU Preset Price Setting or Changing 6.24 PLU Preset Price Setting or Changing The preset price of each PLU may be set in the PLU TABLE PROGRAMMING already described. However, in setting or changing the price only (not other programmed data), the following operation will be more convenient. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
PAGE 141
6. TERMINAL FILE PROGRAMMING EO3-11106 6.24 PLU Preset Price Setting or Changing NOTES: 1. When no price is input then the [Enter] key is depressed, the PLU will be open (i.e. open-price PLU). 2. If inputting a nonexistent PLU code that was not programmed in the PLU Table Programming, this may cause an error. 3. The [PLU] key depression here results in that the next PLU code (i.e. the currently programmed PLU code plus 1) is displayed.
PAGE 142
6. TERMINAL FILE PROGRAMMING EO3-11106 6.24 PLU Preset Price Setting or Changing (continued from the previous page) Operation LCD Display Remarks Make sure the cursor is shown on 01PRICE. Then, input 315 and depress the [Enter] key. The 1st preset price is changed from €1,05 to €3,15. Make sure the cursor is shown on 022ND PRICE. Then, input 540 and depress the [Enter] key. The 2nd preset price is changed from €2,10 to €5,40. As the 3rd preset price remains unchanged, depress the [PLU] key.
PAGE 143
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting 6.25 PLU Preset-Code Key Setting When there are any keys programmed as PLU Preset-code Keys (SFKC 96) on the ECR Keyboard (ordinary or Flat type), and /or when the PK-2 PLU Keyboard (hardware option) is connected to the ECR, a PLU code may be preset to each of those keys in this operation.
PAGE 144
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting • For PK-2 Keyboard Main Menu ECR is being outside a sale and in SET mode. Depress [↓] twice then [Enter]. or Depress [3]. “3 DP/PLU” is selected. Depress [↓] then [Enter]. or Depress [2] “2 PLU” is selected. Depress [↓] twice then [Enter]. or Depress [3]. “3 ASSIGN TO KEYBOARD” is selected. Depress [Enter]. or Depress [1] “1 PK-2” is selected. Input a PLU Code. A 4-digit PLU code to be assigned to a key is specified.
PAGE 145
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 146
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting (continued from the previous page) Operation LCD Display Remarks Depress the [↓] key. The cursor is moved on to “2 PLU CODE KEY”. Depress the [2] or [Enter] key. “2 PLU CODE KEY” is selected. Input 55, then depress the [Enter] key. On this screen, when inputting a PLU code then depressing a PLU preset-code key, the [PLU] key setting is possible.
PAGE 147
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting (continued from the previous page) Operation LCD Display Remarks Depress the [↓] key. The cursor is moved on to “2 PLU”. Depress the [2] or [Enter] key. “2 PLU” is selected. Depress the [↓] key twice. The cursor is moved on to “3 ASSIGN TO KEYBOARD”. Depress the [3] or [Enter] key. “3 ASSIGN TO KEYBOARD” is selected. Depress the [1] or [Enter] key. “1 PK-2” is selected. Input 1111, then depress the [Enter] key.
PAGE 148
6. TERMINAL FILE PROGRAMMING EO3-11106 6.26 %+ and %- Preset Rate Setting 6.26 %+ and %- Preset Rate Setting A preset rate may be set on each of the [%+] and [%-] keys, one independent rate for each key. Once a rate is preset, the % key will simply be depressed without a prior rate entry to activate the preset rate. If a rate is entered prior to the depression of the key, the entered rate (manual rate) will be activated instead.
PAGE 149
6. TERMINAL FILE PROGRAMMING EO3-11106 6.26 %+ and %- Preset Rate Setting 3) Example To program the following rate on the [%-] key: [%-] key ………. Rate 5,00% Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key three times. The cursor is moved on to “4 RATE, LIMIT AMOUNT”. Depress the [4] or [Enter] key. “4 RATE, LIMIT AMOUNT” is selected. Depress the [1] or [Enter] key. “1 %- RATE (%-/%+)” is selected. Depress the [1] or [Enter] key.
PAGE 150
6. TERMINAL FILE PROGRAMMING EO3-11106 6.27 VAT or Add-on Tax Rate Setting 6.27 VAT or Add-on Tax Rate Setting The rates of VATs or Add-on Taxes are set in this operation,. (Which VAT or Add-on Tax is applicable to each Department or PLU has already been set in the DEPARTMENT TABLE PROGRAMMING and PLU TABLE PROGRAMMING.) CONDITION After Financial Daily Reset OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
PAGE 151
6. TERMINAL FILE PROGRAMMING EO3-11106 6.27 VAT or Add-on Tax Rate Setting 3) Example To set the following VAT rate: VAT1………10% Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key three times. The cursor is moved on to “4 RATE, LIMIT AMOUNT”. Depress the [4] or [Enter] key. “4 RATE, LIMIT AMOUNT” is selected. Depress the [↓] key The cursor is moved on to “2 VAT/TAX RATE”. Depress the [2] or [Enter] key. “2 VAT/TAX RATE” is selected.
PAGE 152
6. TERMINAL FILE PROGRAMMING EO3-11106 6.28 Foreign Currency Exchange Rate Setting 6.28 Foreign Currency Exchange Rate Setting The rate of each foreign currency (corresponding to the [CUR1] to [CUR5] keys) are set in this operation. By setting a rate on each Foreign Currency Key, reading the sale total and tendering in the foreign currency value will be possible for sale finalization.
PAGE 153
6. TERMINAL FILE PROGRAMMING EO3-11106 6.28 Foreign Currency Exchange Rate Setting Foreign Currency Exchange Rate Calculation 1. 2. 3) The rate must be calculated in the subsidiary currency unit values for both the domestic and the foreign currencies. (In case of calculating the rate from the domestic to a foreign currency with the same zerosuppress form, such as from Euro to U.S. $, it will be no problem even if it is calculated in the main currency of Euro and $.
PAGE 154
6. TERMINAL FILE PROGRAMMING EO3-11106 6.28 Foreign Currency Exchange Rate Setting (continued from the previous page) Operation LCD Display Remarks Make sure the cursor is shown on 01CUR1. Then, input 1.20 and depress the [Enter] key. The exchange rate from € to $ is set on the [CUR1] key. Make sure the cursor is shown on 02CUR2. Then, input 1.3774 and depress the [Enter] key. The exchange rate from € to Japan Yen is set on the [CUR2] key. Depress the [↓] key twice.
PAGE 155
6. TERMINAL FILE PROGRAMMING EO3-11106 6.29 Negative Amount Key Limit Amount Setting 6.29 Negative Amount Key Limit Amount Setting The limit amount to be entered through each of the negative-amount keys [VND CPN], [STR CPN], and [-] Are set here. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] three times then [Enter]. or Depress [4]. “4 RATE, LIMIT AMOUNT” is selected.
PAGE 156
6. TERMINAL FILE PROGRAMMING EO3-11106 6.29 Negative Amount Key Limit Amount Setting 3) Example To set the following preset amount on the keys below: Key Limit Amount [VND CPN] 10.00 [STR CPN] 20.00 Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key three times. The cursor is moved on to “4 RATE, LIMIT AMOUNT”. Depress the [4] or [Enter] key. “4 RATE, LIMIT AMOUNT” is selected. Depress the [↓] key three times.
PAGE 157
6. TERMINAL FILE PROGRAMMING EO3-11106 6.30 Time Setting or Adjustment 6.30 Time Setting or Adjustment CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] four times then [Enter]. or Depress [5]. Depress [1] or [Enter]. “1 TIME” is selected. Input a 4-digit time value. 4-digiti-time value (HHMM) (See NOTE below.) This setting is ended.
PAGE 158
6. TERMINAL FILE PROGRAMMING EO3-11106 6.31 Date Setting or Adjustment (continued from the previous page) Operation LCD Display Remarks Input 1315. The time “13:15” is set. The [End] key depression allows the ECR to end this setting. A long receipt is issued and the display returns to Main Menu screen. 31-10-2005 MON #0 TIME 13:15TM 0026 13:15TM 6.
PAGE 159
6. TERMINAL FILE PROGRAMMING EO3-11106 6.31 Date Setting or Adjustment 3) Example To set Date “Monday 31 October, 2005” Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key four times. The cursor is moved on to “5 BASIC”. Depress the [5] or [Enter] key. “5 BASIC” is selected. Depress the [↓] key. The cursor is moved on to “2 DATE”. Depress the [2] or [Enter] key. “2 DATE” is selected. Depress the [↓] key. 1 31 10 2005 Input 131102005.
PAGE 160
6. TERMINAL FILE PROGRAMMING EO3-11106 6.32 Store/Register No. Setting 6.32 Store/Register No. Setting A maximum of 6 digits may be set as ID No. for the store and/or register. And once set, it will be printed on every receipt. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] four times then [Enter]. or Depress [5]. Depress [↓] twice then [Enter]. or Depress [3]. “3 REGISTER NO.
PAGE 161
6. TERMINAL FILE PROGRAMMING EO3-11106 6.32 Store/Register No. Setting (continued from the previous page) Operation LCD Display Remarks Depress the [↓] key twice. The cursor is moved on to “3 REGISTER NO.”. Depress the [3] or [Enter] key. “3 REGISTER NO.” is selected. Input 3001. (Store/Register No. 3001 is set.) A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this setting.
PAGE 162
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting 6.33 Hourly Range Table Setting By setting a maximum of 24 terms per day, sales data control for each term can be performed. CONDITION After Hourly Range Reset OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] four times then [Enter]. or Depress [5]. Depress [↓] three times then [Enter]. or Depress [4]. Depress [1] or [Enter].
PAGE 163
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting 3) Example To set the following hourly range table: TIME01 until 8:00* TIME02 8:00 to 12:00 TIME03 12:00 to 15:00 TIME04 15:00 to 19:00 *(The first term is automatically continued from 19:00 of the preceding day.) Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key four times. The cursor is moved on to “5 BASIC”. Depress the [5] or [Enter] key. “5 BASIC” is selected.
PAGE 164
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting (continued from the previous page) Operation LCD Display Remarks Input 1500, then depress the [Enter] key. (TIME03 is set with 15:00.) Input 1900, then depress the [Enter] key. (TIME04 is set with 19:00.) A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this setting.
PAGE 165
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting (continued from the previous page) Operation LCD Display Remarks “2 RESET” is selected. Depress the [2] or [Enter] key. A guidance message is displayed. A long receipt is issued and the display returns to Main Menu screen. The [End] key depression allows the ECR to end this setting.
PAGE 166
6. TERMINAL FILE PROGRAMMING EO3-11106 6.34 Tone Volume Setting 6.34 Tone Volume Setting Key-in tone for the ECR keyboard and error tone are selectable from High, Low, and OFF. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] four times then [Enter]. or Depress [5]. “5 BASIC” is selected. Depress [↓] four times then [Enter]. or Depress [5]. “5 KEY-IN TONE” is selected.
PAGE 167
6. TERMINAL FILE PROGRAMMING EO3-11106 6.34 Tone Volume Setting 3) Example To change the key tone from “HIGH” (default setting) to “LOW”. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key four times. The cursor is moved on to “5 BASIC”. Depress the [5] or [Enter] key. “5 BASIC” is selected. Depress the [↓] key four times. The cursor is moved on to “5 KEY-IN TONE”. Depress the [5] or [Enter] key. “5 KEY-IN TONE” is selected.
PAGE 168
6. TERMINAL FILE PROGRAMMING EO3-11106 6.35 Report Item Print/Non-Print Setting 6.35 Report Item Print/Non-Print Setting Items to be printed on Financial, Cashier, and Salesperson Reports are set here. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] five times then [Enter]. or Depress [6]. Depress [1] or [Enter] key. “6 OTHER” is selected. “1 REPORT PRINT ITEM” is selected.
PAGE 169
6. TERMINAL FILE PROGRAMMING EO3-11106 6.35 Report Item Print/Non-Print Setting 3) Example To set Item Code 3 “NEG GT” with Non-print status. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key five times. The cursor is moved on to “6 OTHER”. Depress the [6] or [Enter] key. “6 OTHER” is selected. Depress the [1] or [Enter] key. “1 REPORT PRINT ITEM” is selected. Depress the [↓] key twice. (Item Code 3 (“NEG GT”) is selected.
PAGE 170
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 171
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 172
6. TERMINAL FILE PROGRAMMING EO3-11106 6.
PAGE 173
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming 6.36 Key Status Programming Various selective statuses of media keys and other function keys are programmed here. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] five times then [Enter]. or Depress [6]. Depress [↓] twice then [Enter]. or Depress [3]. “6 OTHER” is selected. “3 KEY FUNCTION” is selected.
PAGE 174
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming (continued from the previous page) Operation LCD Display Remarks Depress the [↓] key twice. The cursor is moved on to “3 KEY FUNCTION”. Depress the [3] or [Enter] key. “3 KEY FUNCTION” is selected. Depress the [↓] key twice. The cursor is moved on to “03 CHECK”. Depress the [Enter] key. “03 CHECK” is selected. (Key Code 3 “CHECK” is selected.) Depress the [↓] key, then depress the [→] key.
PAGE 175
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming Key Status Table (Key Code 1 to 20) Bit No.
PAGE 176
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming Key Status Table (Key Code 21 to 42) Bit No.
PAGE 177
6. TERMINAL FILE PROGRAMMING EO3-11106 6.37 Cash Tender key Preset Amount Setting 6.37 Cash Tender Key Preset Amount Setting A maximum of 6-digit amount is preset to the Cash Key ([CASH 1] to [CASH 3]). When depressing the cash key with preset amount in a registration operation, it will be processed as a tendering operation of the preset amount. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
PAGE 178
6. TERMINAL FILE PROGRAMMING EO3-11106 6.37 Cash Tender key Preset Amount Setting 3) Example To preset €10000,00 to the [CASH 1] key and €10,00 to the [CASH 2] key. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key five times. The cursor is moved on to “6 OTHER”. Depress the [6] or [Enter] key. “6 OTHER” is selected. Depress the [↓] key three times. The cursor is moved on to “4 CASH KEY AMOUNT”. Depress the [4] or [Enter] key.
PAGE 179
6. TERMINAL FILE PROGRAMMING EO3-11106 6.38 Drawer Warming Time Setting 6.38 Drawer Warning Time Setting This operation sets the number of seconds as the period of time for the cash drawer remaining open until the alarm buzzer is generated to warn operator to close the drawer. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] five times then [Enter]. or Depress [6].
PAGE 180
6. TERMINAL FILE PROGRAMMING EO3-11106 6.38 Drawer Warming Time Setting 3) Example To set 30 seconds for the drawer warning time. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key five times. The cursor is moved on to “6 OTHER”. Depress the [6] or [Enter] key. “6 OTHER” is selected. Depress the [↓] key four times. The cursor is moved on to “5 DRW WARNING TIME”. Depress the [5] or [Enter] key. “5 DRW WARNING TIME” is selected. Input 30.
PAGE 181
6. TERMINAL FILE PROGRAMMING EO3-11106 6.39 Special Rounding Process Setting, 1-digit type 6.39 Special Rounding Process Setting, 1-digit type For Special Rounding and Denmark/Australia rounding, the pre-rounded value of the least effective digit and the post-rounded value are set here. This operation is effective when the option “Special Rounding ACTIVE” and “1 digit subject to Special Rounding” are selected (System Option Address No. 33, Bit No. 3 SET & Bit No. 4 RESET).
PAGE 182
6. TERMINAL FILE PROGRAMMING EO3-11106 6.39 Special Rounding Process Setting, 1-digit type Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key five times. The cursor is moved on to “6 OTHER”. Depress the [6] or [Enter] key. “6 OTHER” is selected. Depress the [↓] key five times. The cursor is moved on to “6 ROUND TBL 1 DIGIT”. Depress the [6] or [Enter] key. “6 ROUND TBL 1 DIGIT” is selected. Input 200, then depress the [Enter] key.
PAGE 183
6. TERMINAL FILE PROGRAMMING EO3-11106 6.40 Special Rounding Process Setting, 2-digit type 6.40 Special Rounding Process Setting, 2-digit type For Special Rounding and Denmark rounding, the pre-rounded value of the two least effective digit and the postrounded value are set here. This operation is effective when the option “Special Rounding ACTIVE” and “2 digits subject to Special Rounding” are selected (System Option Address No. 33, Bit No. 3 SET & Bit No. 4 SET).
PAGE 184
6. TERMINAL FILE PROGRAMMING EO3-11106 6.40 Special Rounding Process Setting, 2-digit type Example of Denmark rounding For the Denmark rounding, the amount total is rounded as shown below. Pre-rounded value of the Post-rounded value two least effective digits 0 to 12 00 13 to 37 25 37 to 62 50 63 to 87 75 88 to 112 100 3) Example To set the Denmark rounding.
PAGE 185
6. TERMINAL FILE PROGRAMMING EO3-11106 6.40 Special Rounding Process Setting, 2-digit type (continued from the previous page) Operation LCD Display Remarks Input 3725, then depress the [Enter] key. Input 6250, then depress the [Enter] key. Input 8775, then depress the [Enter] key. The [End] key depression allows the ECR to end this setting. A long receipt is issued and the display returns to Main Menu screen.
PAGE 186
6. TERMINAL FILE PROGRAMMING EO3-11106 6.41 Number of Receipt Print Buffer Line Setting 6.41 Number of Receipt Print Buffer Line Setting The number of receipt print buffer line is set here. When it reaches the set value, only a receipt print operation starts. This setting is effective only in REG, MGR, and - modes or programming operation. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
PAGE 187
6. TERMINAL FILE PROGRAMMING EO3-11106 6.41 Number of Receipt Print Buffer Line Setting (continued from the previous page) Operation LCD Display Remarks Depress the [↓] key seven times. The cursor is moved on to “8 RCT PRINT BUFFER”. Depress the [8] or [Enter] key. “8 RCT PRINT BUFFER” is selected. Input 30. Number of receipt print buffer line: max. 2 digits (1 to 50) The [End] key depression allows the ECR to end this setting.
PAGE 188
6. TERMINAL FILE PROGRAMMING EO3-11106 6.42 Serial No. Setting 6.42 Serial No. Setting A maximum of 8-digit serial No. is set here. The serial No. will be printed on the Daily and GT Financial Read/Reset Reports. CONDITION Any time outside a sale OPERATION Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [↓] five times then [Enter]. or Depress [6]. Depress [↓] eight times then [Enter]. or Depress [9]. Input a Serial Number.
PAGE 189
6. TERMINAL FILE PROGRAMMING EO3-11106 6.42 Serial No. Setting 3) Example To set the serial No. 12345678. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [↓] key five times. The cursor is moved on to “6 OTHER”. Depress the [6] or [Enter] key. “6 OTHER” is selected. Depress the [↓] key eight times. The cursor is moved on to “9 SERIAL NO.”. Depress the [9] or [Enter] key. “9 SERIAL NO.” is selected. Input 12345678.
PAGE 190
7. VERIFICATION OF PROGRAMMED DATA EO3-11106 7. VERIFICATION OF PROGRAMMED DATA 7. VERIFICATION OF PROGRAMMED DATA The programmed data entered in the preceding chapter can be read for verification purposes. The print format of each program reading is almost the same as on the program receipt, except that “X” is printed instead of printing Program Name. 1. 2. 3. 4. CONDITION Any time outside a sale OPERATION Mode Lock: X or SET Turn the Mode Lock to the X or SET position with the MGR key.
PAGE 191
7. VERIFICATION OF PROGRAMMED DATA EO3-11106 7.