ii_ii_iiiiiiiii_iiiiiii_iii_iii_i_i .... TOSHIBA SERVICE FILE NO.
CAUTION THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACTAN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.
SERVICING 1. KEEP THE NOTICES ON CHECKING 6, AVOID AN X-I_Y NOTICES As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual. 2, AVOID AN ELECTRIC SHOCK There is a high voltage part inside. Avoid an electric shock while the electric current is flowing. 3.
IMPORTANT 1. 2. 3. 4. 5. 6. 7. SAFEGUARDS READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. CLEANING Unplug this unit from the wall outlet before cleaning.
IMPORTANT SAFEGUARDS (CONTINUED) 17. OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and buifi-up static charges.
IMPORTANT SAFEGUARDS (CONTINUED) EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA JNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQL GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS NEC-NATIONAL POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) ELECTRICAL CODE $2898A A1-5
DISC REMOVAL METHOD AT NO POWER SUPPLY 1, Remove the Back Cabinet and AV PCBiDVD Block, (Refer to item 1 of the DISASSEMBLY iNSTRUCTIONS.) 2, Slide the Rack Loading (White) toward the arrow direction by using a minus driver to release the lock, (Refer to Fig. 1) 3, Draw the Tray. Rack Loading (White) I I I I Deck CD I L_ I I © o o Fig. 1 PARENTAL CONTROL 4 DIGIT PASSWORD If the stored below, 1, 2, 3. 4. 5.
TABLE OF CONTENTS ............................................................................................................................ CAUTION SERVICING HOWTO NOTICES ON CHECKING .......................................................................................................... ORDER PARTS IMPORTANT ..................................................................................................... SAFEGUARDS METHOD AT NO POWER SUPPLY ...............................................
GENERAL G-t IV CRT SPECIFICATIONS CRT Size i Visual Size t3inch Normal CRT Type Deflection System Magnetic Field 90 degree +045G / 0.18G NTSC BViBH Color System Speaker Sound Output G-2 DVD System Position Size 2 Speaker Front t .5 x 2.7 inch Impedance Max t0%(Typical) 8 ohm t.5W + 1.5W t.OW + 1.0W NTSC Color System Disc Disc Diameter Deck i 335.
GENERAL G-g On Screen Display SPECIFICATIONS MenuffV) Menu Type TV Setup Picture Audio Bictu_ Preference Channel Setup TViCATV Auto CH Memory Add/Delete V_chip Setup Language Sleep Timer CH / AV(LINE) Stereo/Audio i DVD Output Icon Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Bilingual SAP Control Volume Level Bright / Contrast i Sharpness Tint Bass#r rebleiBalance i Color Yes Yes Yes Yes No Yes Caption i Text Auto Search/Position Game Mute No Yes Yes A3-2
GENERAL G-10 011 Screen SPECIFICATIONS Menu (DVD) Yes Character Yes Yes Yes Yes Yes Yes Yes MenuType Display Language Menu SubtitEe Audio Picture TV Screen Size OSD Display On/Off JPEG Interval Select Files No No Yes Yes Sound DRC (Dynamic dts Decode Range Control) No No No No No Output(5 lchi 2ch) Surround OniOff Center On/Off Sub Woofer On/Off Yes Yes Yes Yes Yes Parental Password Lock/Un Lock Rating Level Other OSD Language(Set up Language) Output(RGBiCorqposite) Open Close No disc Read
GENERAL G-13 Remote Control Unit Glow in Dark Remo-'_on Format Custom Code Power Source Total Keys Keys SPECIFICATIONS RC-GD NEC 7t-8E h 3V Voltage(D.
GENERAL G-14 Features SPECIFICATIONS CATV Auto Shut Off Yes Auto CH Memory V-Chip USA V-chip CANADA V-chip Auto Search SAP Game Position FM Transmitter Energy Star Closed Caption Comb Filter P_etestof FBT Leak Circuit Choke Coil No No Yes No No No No No Power On Memory Tray Lock Parental Lock (DVD Only) Video CD Playback SVCD Playback No No No No No No No Overlay Graphics And Text Command List Entry Point Jump MP3 Playback WMA Playback JPEG Playback Digital Out Down Mix Out (Dolby Digital) (MPE
GENERAL G-16 Interface Switch Front SPECIFICATIONS Power (Tact) Channel Up Channel Down Yes Yes Yes Volume Up Volume Down Yes Yes Yes Piny Open/Close Skip(>>) Rear Indicator Yes Yes Skip(l<<) Still/Pause Yes Stop Main Power SW Main Power SW Power Yes No No No Yes (Red) No No Stand-by On Timer Terminals Rear G-17 Set Size G-18 #/eight G-19 Carton RCA x 1 Video input Audio Input Other Terminal Front RCA x 2(Stereo) Head Phone No No No Video input Audio input Video Output No Au
DISASSEMBLY 1. REMOVAL OF MECHANICAL AND P.C. BOARDS INSTRUCTIONS PARTS 1-3: AM PCB/DVD BLOCK (Refer to Fig. 1-3) 1. Remove the 2 screws 1i. 2. Disconnect the following connectors: (CP301, CP302, CP401 and CP3800). 3. Remove the AV PCB/DVD Block in the direction of arrow, 1-1 : BACK CABINET (Refer to Fig. 1-1) 1, Remove the 2, Remove the Cabinet. 3. Remove the 4, Remove the 4 screws ,i), screw z which are used for holding the Back AC cord from the AC cord hook _.
DISASSEMBLY INSTRUCTIONS 1-5: DVD PCBIDVD DECK (Refer to Fig. 1-5) 1. Make the short circuit on the position as shown Fig. 1-5 using a soldering. If you remove the DVD Deck with no soldering, the Laser may be damaged. 2. Unlock the 2 supports i), 3. Remove the Front Tray Plate in the direction of arrow (A), 4. Disconnect the following connectors: (CP2601, CP2602 and CP2603), 5. Remove the 4 screws '2. 6. Remove the DVD Deck in the direction of arrow (B), 7. Remove the 4 screws '_. 8.
DISASSEMBLY 2. REMOVAL INSTRUCTIONS OF DVD DECK PARTS Ma;n Chsssis Assy NOTE 1, Do not disassemble the DVD DECK PARTS except listed parts here, Minute adjustments are needed if the disassemble is done. If the repair is needed except listed parts, replace the DVD MECHAASS'Y, 2-1 : TRAY (Refer to Fig. 2-1-A) 1, Set the Tray opened. (Refer to the DISC REMOVAL METHOD AT NO POWER SUPPLY) 2, Unlock the support 1 and remove the Tray. / Malr_ ran!e Ass'y \ Mair_ ran!e Ass'y 2-3: RACK LOADINGIMAIN GEAR/RACK
DISASSEMBLY INSTRUCTIONS NOTE Main Chassis Ass'y 1. When installing the Clamper Magnet, install it with the green face up. 2. When installing the wire of the Lever Switch, install it correctly as Fig. 2-4-B. 3. When installing the Lever Switch, install it correctly as Fig. 2-4-C. 4. In case of the Lever Switch installation, hook the wire on the Main Frame as shown Fig. 2-4-D. 2-6: SWITCH PCB ASS3" (Refer to Fig. 2-6-A) 1. Remove the screw ,i!. 2. Remove the Switch PCB Ass'y.
DISASSEMBLY INSTRUCTIONS NOTE 2-9: GEAR (Refer to Fig. 2-9-A) 1, After the assembly of the Rack Feed, check if the Rack Feed 1/2 is moving smoothly. (Refer to Fig. 2-7-B) 2, In case of the Rack Feed Ass'y installation, install correctly as Fig. 2-7-C, 1. Un ock the support 2. Remove the Middle Gear 1/2/3, Idler Gear and Feed Gear, Middle Gear 2 M_ddle Gear 3 4 dler Gear Moving smoothly Fig. 2-7-B Malr_ Ch_ Fig. 2-9-A NOTE 1. In case of the Idler Gear installation, install correctly as Fig.
DISASSEMBLY INSTRUCTIONS 2-11: FEED MOTOR (Refer to Fig. 2-11-A) 1, Remove the 2 screws _i), 2, Remove the Feed Motor. 3, Remove the Motor Gear, • _¢rew Torque; 1 _ 0 bl{gf,cm Fig. 2-11-A NOTE 1, In case of the Motor Gear installation, check if the value of the Fig. 2-11-B is correct. 2, When installing the Feed Motor, check if the cable is positioned as Fig. 2-11-C, Motor__(Gear 6 Safety $L_rface for _ressirl_ of tbe ir!sei_, Mair_ Chassis £ 0 rnrn Fig.
DISASSEMBLY INSTRUCTIONS 3. REMOVALOFANODECAP 3, After one side is removed, pull in the opposite direction to remove the other. Read the following NOTED items before starting work. NOTE * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged.
DISASSEMBLY 4. REMOVAL PACKAGE AND INSTALLATION IC INSTRUCTIONS OF FLAT 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 4-3.} REMOVAL 1.
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge*soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 4-8.) f. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern, Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig, 4-5,) _C Thimtip Soldering / Sotdedng Iron Iron / Fig. 4-8 Solder temporarily 5.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously for more than a standard time (second). Set Key VOL. (_) MIN I I Remocon Key Standard Tim_ (seconds) 0 1 1 1 I Releasing of V-CHIP PASSWORD. I I Initialization I 4 1 The function will only work at the DVD stop mode. I I I POWER ON total hours are displayed on the screen.
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need setting for after INI 27.
ELECTRICAL 1. BEFORE MAKING ADJUSTMENTS ADJUSTMENTS ELECTRICAL Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION • Use an isolation transformer when performing any service on this chassis. • Before removing the anode cap, discharge electricity because it contains high voltage. • When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position.
ELECTRICAL ADJUSTMENTS 2-4: WHITE BALANCE 2-8: VERTICAL NOTE: Adjust after performing CUT OFF adjustment. NOTE: Adjust after performing adjustments in section 2-7. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4.
ELECTRICAL ADJUSTMENTS 2-10: OSD HORIZONTAL 2-13: TINT CENTER 1, Activate the adjustment mode display of Fig, %1. 2. Press the VOL, UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig, 2-1) 1. 2. [] 01OSD 13 r_ 13 [] [] [] [] [] [] 12 3. 4. 5. [3 13 13 13 6. 7. 13 [3 8. B 9. 2-11: LEVEL 10. 1. Receive the VHF HIGH (70dB). 2. Connect the AC voltmeter to pin 6 of CP101. 3. Activate the adjustment mode display of Fig.
ELECTRICAL ADJUSTMENTS 2-14: COLOR CENTER 2-15: CONTRAST 1, 2. 1. Activate the adjustment mode display of Fig. %1 and press the channel button (22) on the remote control to select "CNTX". 2. Press the VOL, UP/DOWN button on the remote control until the contrast step No. becomes "5A" 3. Receive a broadcast and check if the picture is normal. 4. Press the INPUT SELECT button on the remote control to set to the AV mode, 5. Activate the adjustment mode display of Fig.
ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 3-4: DYNAMIC CONVERGENCE 1. Tighten the screw for the magnet.
ELECTRICAL 4.
DVD BLOCK DIAGRAM FLASH IC4007 SST39VF800A70-4C-EK 64M SDRAM IC4005 M12L64164AWT HA0~HA20, HD0-HD15 DVD LOADER DM_ Pick up RF IC2601 A,CD, B, C, D, E, DVD, LDF i tr I I ZR36708TQC "_ i '_ I Dual OP-AMP IC2602 BA10358F-E2 ( TX I > ( RX P.CON+3.3V ( P.CON+5V ( P.
TV BLOCK DIAGRAM RESET IC103 PST3231NR *A POWER ON/OFF I/ I TU001 SCL SDA OPEN/CLOSE MiCON IC101 OEC6079A STOP 16MHz Xl01 PLAY Q105 SKiP FF [ BUFFER t SKiP REW FROM DVD BLOCK I I *B *C I DVD C DVDY I i) I) I DVDRESET i( I RX I< TX I) # I I l DVD [ AMP ] A OUT L _-'_'-_3_ IC4201 _1_ - _ 1 NJM4580M I f--_ _TEI' _ R.OUT G,OUT V801 B.
POWER BLOCK DIAGRAM Q3003, Q3004, Q3007 IP.OON+3.3VOUT I 5V REG. IC3001KIA7805API P.CON+3.3V I < DVDH ) P.CON+D5V DEGAUSS COIL L3800 AT+5.6V F3800 D3808, D3809, TRANSFORMER SWITCHING D3815, D3816 T3800 __J SOUND+B 5V REG. IC3800 Q3800 FEED BACK CONTROL PS2561Ll-l-V(W) IC3002 Q3803 KIA7805API powER I P.CON+5V +9V REG. IC3005 KIA7809API Q3010 I O_lW I ) P.CON+D9V ) P.CON+9V ) P.
PRINTED DVD (TOP SIDE) F-I CIRCUIT BOARDS DVD (BOTTOM SIDE) F-2
PRINTED CIRCUIT BOARDS AV/CRT (INSERTED PARTS) SOLDER SIDE F-3 F-4
PRINTED AV/CRT CIRCUIT (CHIP MOUNTED SOLDER F-5 BOARDS PARTS) SIDE F-6
PRINTED RELAY (INSERTED CIRCUIT BOARDS RELAY PARS) SOLDER SIDE (CHIP MOUNTED SOLDER SIDE PARS) S_0_SX S_O01X S_O03X SW SOLDER SIDE F-7 F-8
A I B I o I D I E I F I G I H MPEG/MIOONSCHEMATICDIAGRAM (DVD PCB) [[ FROM/TO AUD ONID£O 0(}1 _DAC _DAC _DAC _ASDATAO _ABCLK _ALRCLK _AMCLK _MD _MC _ML _RESET B DUPTDI JPRDI JPTDO v GND JPRDO ]] VIDEO C VIDEO 8 VIDEO D CON+5_ W831 _N_ D GND _i=i B4002 FC_2012H-IO2T04 B4001 FC_2012H-IO2T04 +_ 8V +3 3V D GND P CON+3 3V [[ FROM/TO RF AMP/DSP B4003 FCM2012H _02T(}4 B4004 FCM2012H SW _02T(}4 B4005 [E FC_2012H-IO2T04 ( F HA_ HA_ HA_ HA3_ HA,_ HA_.
A I B I o I D I E I F I G I H G I H MEMORYSCHEMATICDIAGRAM (DVD PCB) FLAS C 8M 104007 SST39VFSOOA-70-4C-£K SO A_ SO A_ SO A_ SO SO SO A_ SO A" SO A_ SO A_ S{) A_ SD AI_ SD AI_ SO D_ SO DI_ SO D_ SO D_ SO D_ $9 D_ _ $9 D_ . SO D7_ SO DS_ SD D_ SD DI_ SD DI_ SD DI _ SD DI_ SD DI_ SD DI_ RAMCS_ RAMCSI_ RAMRA" RAMCA_ SD B_ RAMD_ RAMW_ RAMCL4_-HA_ HA_ HA HA_ HA_ HA = . HA_ _ HA_ HA_ HA_ HAI_ HA1 : . HAI_ HA1" _ HAI_ HAI_ _ HAI_ HAI_ HAI_ HA1r HA2_ HD_ HD_ _ HD_ HD" .
A I B I o I D I E RFAMP/DSPSCHEMATICDIAGRAM I F I G I H (DVD PCB) FFC(P_O5mm) CD2601 2H001901 == TOUTSW 0£ VR DVD CTL 02603 2SK3018 CP2601 IMSA.9631S.24Y901 0 R2620 G 5 0 TRTR+ VR CD CT 02604 2SK3018 _n G f_^^_ R2647 FO+ DWPD TP8 ° .
A I B I o I D I E AUDIONIDEOSCHEMATICDIAGRAM I F I G (DVD PCB) - p CON+A5%r - : - H 1 2 3 4 A Y G B V R Y V C U B C U D C CVBS CVBS CVB8 CVBS Y : PCON+A5V > I W876 _ DAC C[C VIDE[ DAC VIDEO C W877 o_o DAC VIDEO 0 DAC VIDEO D DAC B/Y ! VIDE[ w87_ PCON+5V _-_ DAC DDwViDE PCON+33V_ DAC ViD C8505 I_T ° 12_ o _ 1" ° 0 6 14 08502 vlDOBUFFER KTA1504S Y 0 VIDEO SUFFER Q8503 RESE_ I M_ 1211 CH DAC VDEO B 08508 = _{i _{TA1504S Y 0 6 0 T_{ ?
A I B I o I D I E I F I G I H REGULATORSCHEMATICDIAGRAM (AV PCB) UNREG+12V ) UNR£G+SV ) UNREG+_V ) GND [E FROM/TO SOUND AMP_ GND UNREG+12V IN GNO 33V O_T 03003 _TC4369 OUT IOUN TSL0801 ) P CON+gV ) p CON+5V ) 8__ Q3006 DRIVER D3008 AT+56V DRIV£R PCON+12V o KTC3203 KTA1281Y Y III IN4005-_1C GND > B _ 79_ DRIWH Q3Olu 80 I C3005 16V470 YK 1181 I R3011 I IM 1/4w FROM/TO VIF/SIFICNROMA 1 i IK 1/4W 763WAA0157 HS3001 _ _.
A I B 0 I D I E F I I G I a MICON/TUNERSCHEMATICDIAGRAM (AV PCB) o co _o 2, [E FROM/TO IN/OUT 1 SCL > NO NO NO NC NO NC NC , NC _NC ,_ SDA > _1 _ 2C OFF RE_OCON I KEY A R119 '52 Y D106 KEY B > 10K POWER ON H O101 I RESET IC KTA1504S Y RTK IC103 PST8231NR I II _ R125 1_ X101 _ D101 OSD Y CSTLS16MOX53-A _! OSD B OSD G OSD R SDA _E SCL 2 _4 SYNC V_DEO _24 I1 CONTROL > 0IF PROTECT POWER ON H TUNER VIDEO /i/i/-_/i SWD V OUT W837 ItD V-BUFFER Q105
A I B I o I D I E VIF/SIF/CHROMASCHEMATICDIAGRAM I F I G I H (AV PCB) i DVD y ° ) © DVD C NREG+12V ) P CON+5V GN£ ) o< SO02X C4227 P CON+gV ) SWD V OUT AT5 7VREC 50V 1 KA 8 5VREC R6 22 VOUT ACL ( AFC HOUT ( CROMA IC601 IC NCO LA7631£M-MPB-[ NCO C628 NCo FRONTVIDEO 50V 047 NC SWD VIDE_ C622 • 50V DVD Y _ C601 01 R630 0SD Y IK IRW B R619 0SD B 4 7K +.
A I B I 0 I D I E I F I G I H SOUNDAMP SCHEMATICDIAGRAM (AV PCB) SOUND AM9 IC Z_ IC302 AN7522N if C_301 TID-X02P-M1 CD301 CU12414A LCN SPEAKER ,_ SP351 SGO4D11BNA 8 OHM RCH SPEAKER SOUND_B W4BRH35X6X10 SOUND _ SP352 SGO4DIISNA 8 OHM B301 CND _FROMT[OREGULATOR_ W813 oe_o GND <* FROM MICON/TUNER_ R302 _,N_, _RK POWER ON II A MUT£ ) VOL PWM > _Z > o o' o> R301 A OUT L P CON+2 A OUT R A I ) KBid_iqS 120 y RT _ _K_/'/4W R303 ',M, 2 2K /4W _ NOlO:f HE DC VOLTAGE A
A I B I o I D I E I F I G I H IN/OUTSCHEMATICDIAGRAM AT+56V (AV PCB) 0S2202 PIC-37243SR R2202 100 I/4W a_ SW 02201 DTC124EKA R2214 R2216 R2218 R2220 R2221 REMOCON AOL . AO - AT+56V SOUND GND DVD AUDO _EY A DVD AUDO FRONT A N L _EY B .
A I B I o I D I E I F I G I H STEREOSCHEMATICDIAGRAM (AV PCB) L904 IO0_H _;_ ( TUNER AUDIO ( SCL ( ) SDA R912 10(} _/4W / _ )_ AOUTL AOUTR _ P CON+12 ( A0R A A0L _DVDAUDIOL _DVDAUDIOR 4
A I B I D I D I E I F I G I N DEFLECTION SCHEMATICDIAGRAM (AVPCB) 8 8 _:_ AI561WV2ASF _6 FROM/TO V HS F/C ROMA]] R412 VOUT ACL ) 33K ) 1/4W R420 AF_ 2 2K R424 V_ 3 3K 1/4W z_ W914 C431 _+ I _R402 _f_ 9406 330 2W W916 _SS133 ISS133 220 V801 A34AGT13X98(_L) _ 250V 22 YK _ IW _- _ Z_FB401 1 FM-14EO01 SMIO98-OO9-1A o H OUTPUT _ TT2140LS-YSCH 0 FOCUS C429 / 500V 0 0022 B | IN4937 _ 42 R409 _ R450 _ > D414 (C9803_}C_803 B2013HO24P _N4OOS-EIC 350 T T
A I B I o I D I E I F I G I H I H CRTSCHEMATICDIAGRAM (CRT PCB) CPS02B (CPS02A) B2013H026p CPS03B(CPS03A) B2013N02-4P CPS01(CDS05} A2361WV2-2P 2SC4217 2SC4217 FOCUS SCREEN SCR£EN 8P806 1 _> z_ CRTSOCKET J801 1 ISMS01S ACC£SSORY TMI01 TOT201N09160 BL001 HpN-01 BT001 BT002 D D R03(AB)[2P G UM4 NO[£:THIS SCHLMA] IC DIAGRAM IS file LATESf AI ]HE [IML OF PRINTING AND SUBJECf [0 CRANGL WITHOUT NO[ICL o NOfE:[HE DC VOL[AGE AT EACHPAR[ WAS MEASURED WI[H 1NL DIGIIAL [LSILR WHLN IHL
A I B I o I D I E I F I G I H POWERSCHEMATICDIAGRAM (AV PCB) ,_3823 SB340L'6737 _ F PH3800 003P-2100 8RI40031 , PH3801 O03P 2100 !!, CP380(} D3821 _1_ o _B UNR£G+12V GND ,_ _ _T RU2AM'£1C TH3800 2 ZPB45BL3ROA R3828 _,NV¢ (}22 _W w D3818 R3829 _N4937 Q L3803 _00 1/4W R3830 _ IK 1/4W I , C3810 $3802 > C3812 D3817 ,_ 50(}V 500V ,, T, T i SOUND GND o> _SOUND+B o L 3826 _W_VV 12M T3800 81291(}74 R3827 _, 1/4W 12M POWER FAIL GND /4W z_ POWER Q3803 STP5
A I B I c I D I E I F I G I H F I G I H RELAY/SW/FG SCHEMATIC DIAGRAM M2002 _CD3B02 M200T JCLgB61 (SW PCB) SW2 $W1A_2J1 _0A S_003X S_003 S1OO3Y S_002X S_002 S1OO2Y i i AWD28 D_ SG 107£6 NOTE:I HE DC VOLTAGE AI EACH PART WAS MEASURED WiTH TIIE DIGit AL TESTERWHEN TIIE COLOR BROADCAST WAS REC_[WD IN GOOD CONDITION AND PICTURE IS NORMAL¸ NOTE:THIS SCHEMAI ]C DIAGRAM IS THE LATEST AI THE T_ME Or PRiNTiNG AND SUBJECT10 CHANGE WITHOUI¸NOTICE o G-27 P I B I c I D I E I
A I B I o I D I E I F I G I H INTERCONNECTION DIAGRAM L_ L_ ]D2601 >S o: C926(}1 24 23 22 COAX AL J4201 FRONTVI0£0 JACK J2202 FRONTA D 0 JACK J22(}3 21 FRONT AUDIO JACK J2204 _ ,& ° HEADPHONE JACK GND : J2201 ]VD) 2(} MON(DVD) _ CD4(}02 ¢_) 19 NC(SW) DRIVE VOL(DVD) DM-2 i Vb ) b) 17 16 _ )) 15 _ LD{CD} O) 14 _ VOL{CD) _D} 13 GND(CD} OM) 12 MON(COM) JC} VD} 11 18 1(} CP8(}01 T _ GND TX RX T T GND(M) 5 P OON+gV T P OON+5V A 7 p CON+3 3V
WAVEFORMS MPEG/MICON MICON/TUNER AUDIO/VIDEO ® .... iiiii .... i i I T ® ® @ MEMORY I _ogs I 12oomv I _ ® i_ _i _ i _i _i _ i- _........._...._,._.... • • .. ® _._ _.:<%__ : @ u RF AMP/DSP @ ................. ® ;.i__i_.J .............. i.¸_ @ i .,... _,_,....,... _ _.;....,.. _ ..,....;.__ ...,....,._ ; _,,_ ® @ .. :_ .,6,_i,:.}._:;_, :.. :. _.;:_ ,._'_ -_=--_:-_:--.:_:_:[:;;----!.--_----_ _}:_i.,_.L ,,_ ........ _......... ,. _ ..... ,_ .., @ :8 _.. !_!,_.%,_,.._.
WAVEFORMS VIF/SIF/CHROMA IN/OUT e ft_,_ J \ @ l \ _7 L _/::
WAVEFORMS @ © i DEFLECTION POWER i i i Z i @ i i _ _F '_ "_ IlIl_ @ .... ii - '_ I_H_"HHIHHIHHHL_H CRT @ H+ _ NOTE: The following waveforms were m,_asur_d at tha poi[_t of the corresponding balloon nurt_bJr in th_ schomatio dia,qrar_.
MECHANICAL EXPLODED VIEW 202 114 206 202 116 201 202 102 201 PCB110 (CRT PCB ASS'Y) 121 201 117 115 210 I i i i It-1
MECHANICAL EXPLODED VIEW 113 112 110 208_ 208 209 2O8 20; 208 0 208 108 PCB130 (DVD PCB ASS'Y) 208 -/ 208 208 203 206 i i i L 107 204 103 207 204 211 _" 211 J" 111 1t-2 PCB250 (AV PCB ASS'Y)
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) 123 _ 127,128,129,130, BLOO1,TMI01 123 123 123 125 \ 124 124 124 11-3
DVD DECK EXPLODED VIEW 613 AA AA 705 _603 AA 615 6107 _602 704 SW2 _ CD2001 (SW Do not replace the parts, Because, ',i minute adjustments are needed if ,i this condition is disassembled further more. i If the repair is needed, replace the ',i i ,• ............................. DVD MECHAASS'Y, 605 CLASS MARK GREASE AA NOTE: Applying positions AA for the grease are displayed for this section. Check if the correct grease is applied for each position.
MECHANICAL Location No. TSB PIN REPLACEMENT PARTS Reference No.
DVD DECK REPLACEMENT Location No. TSB PIN ,_ Reference PARTS No.
ELECTRICAL Location No. TSB PiN Reference AD301016 AD300783 BZ210009 BZ210053 AD300419 AD300036 AD302182 BZ210021 AD30t76t BZ210050 BZ210050 BZ210050 AE002014 AE002014 BZ210206 BZ210080 BZ210217 BZ210t88 AD300659 BZ210t90 R3X28A331J R3Xt81221J R3X28AR82J R002T22R2J R4XST6223F R4XST6562F R002T4153J R65582680J R635815RCJ R3XtSA123J R3XtSA123J R3XtSA123J R00202t R2J R00202t R2J R002T2155J ROG3K2275K R3Xt81331J RSY2CD0t0J R3Xt81R47J R63581R22J 03810 03811 03812 _03815 ,_.
ELECTRICAL Location No.
ELECTRICAL Location No.
ELECTRICAL Location No. PCE250 B301 B401 B260t B2602 B2603 B2604 B2605 B3800 B400t B4002 B4003 B4004 B4005 B4006 B4007 B4008 B4009 B4010 B420t B8502 B8503 EL001 ST001 ST002 CD30t CD302 CD802 CD803 CD805 CPt0t 0P30t 0P302 CP40t CP80t _OD3a00 CD4002 CD8501 CP2601 CP2602 CP2603 _CP3800 0P8001 CP8002 CPS02A CPS02B CPS03A OPS03B 0P8502 OUS0t 1 EL001 EL002 F3800 _FB40t FH3800 Fl/380t OS2202 PH3800 Pl/3801 _SP351 _.
ELECTRICAL REPLACEMENT RESISTOR RC .............. CARBON CC .............. CE ................ CP ............... CPP ............. CPL ............. CMP ................. CMPL ............ CMI=P ............
TOSHIBA 1-I, _t-II_AUIT_ CORPORATION I-CHO_IE, N1tl _TO-I_ U TOK'_ O 105-S001 JAPAtNI
