NB250 Series User’s Guide If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Customer Support Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 137 in this guide.
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Model: NB250 Series Recordable and/or ReWritable Drive(s) and Associated Software Warranty The computer system you purchased may include Recordable and/or ReWritable optical disc drive(s) and associated software, among the most advanced data storage technologies available.
Critical Applications The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interference received, including interference that may cause undesired operation. Contact either: ❖ Toshiba’s Support Web site at pcsupport.toshiba.com.
Wireless LAN and Your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers.
Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s Web site www.hc-sc.gc.ca/rpb. The RF device shall not be co-located with any other transmitter that has not been tested with this device.
The European Union WEEE (Waste from Electrical and Electronic Equipment) Directive Information The European Union WEEE (Waste from Electrical and Electronic Equipment) Directive is intended to protect the quality of the environment and human health through the responsible use of natural resources and the adoption of waste management strategies that focus on recycling and reuse.
Taiwan Article 14 Article 17 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Any use of low power radio frequency electric machinery shall not affect aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued.
2. Indication The indication shown below appears on this equipment. (2) (3) (1) 2.4DSOF4 (4) 1 2 2.4: This equipment uses a frequency of 2.4 GHz. DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 4 The interference range of this equipment is less than 40m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. The indication shown below appears on this equipment.
Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.
Finland Ghana Herzegovina Hungary Indonesia Italy Jordan Kuwait Lebanon Lithuania Malaysia Monaco Nambia New Zealand Norway Panama Peru Portugal Romania Senegal Slovak Republic South Korea Sweden Thailand France Greece Honduras Iceland Iraq Jamaica Kazakhstan Kyrgyzstan Lesotho Luxembourg Malta Montenegro Nepal Nicaragua Oman Papua New Guinea Philippines Puerto Rico Russia Serbia Slovenia Spain Switzerland Turkey Ukraine USA Yemen United Kingdom Venezuela Zimbabwe Germany Guatemala Hong Kong India Ir
Deutschland: France: Italia: Nederland: Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, audessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de l’IBPT est requise. Pour les enregistrements et licences, veuillez contacter l’IBPT. License required for outdoor installations. Check with reseller for procedure to follow.
Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.
Germany Hungary Italy Korea Lebanon Luxembourg New Zealand Peru Portugal Slovenia Switzerland Uruguay Greece Iceland Japan Kuwait Liechtenstein Malta Norway Philippines Singapore Spain Thailand USA Hong Kong Ireland Jordan Latvia Lithuania Netherlands Oman Poland Slovakia Sweden UK Venezuela Bluetooth® Wireless Technology and Your Health The products with Bluetooth® wireless technology, like other radio devices, emit radio frequency electromagnetic energy.
Exposure to Radio Frequency Radiation The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. Regulatory statements This product complies with any mandatory product specification in any country/ region where the product is sold.
Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. ©2010 by Toshiba America Information Systems, Inc. All rights reserved. Export Administration Regulation This document contains technical data that may be controlled under the U.S.
Trademarks Adobe and Photoshop are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Atheros is a registered trademark of Atheros Communications, Inc. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
Contents Introduction................................................................................ 24 This guide ...............................................................26 Safety icons ............................................................27 Other icons used...............................................27 Your computer’s features and specifications ....28 Other documentation ..............................................28 Service options ....................................................
Contents 19 Registering your computer with Toshiba ................38 Adding optional external devices.............................38 Adding memory (optional) ......................................39 Installing a memory module .............................39 Removing a memory module............................45 Checking total memory .....................................47 Recovering the Internal Storage Drive ....................47 Recovering to out-of-box state (recommended recovery method).............
Contents Customizing your computer’s settings....................81 Caring for your computer........................................81 Cleaning the computer ......................................81 Moving the computer........................................82 Using a computer lock ......................................82 Chapter 2: Learning the Basics................................................. 83 Computing tips .......................................................83 Using the keyboard ........
Contents 21 Determining remaining battery power.............100 What to do when the main battery runs low ............................................................100 Setting battery notifications ............................101 Conserving battery power ..............................101 Power Plans....................................................102 Using a hot key to set the Power Plan.............103 Changing the main battery ....................................
Contents Using an instant password..............................126 Using a supervisor password..........................127 Using a user password ...................................128 Deleting a user password................................129 TOSHIBA PC Diagnostic Tool Utility......................130 Mouse Utility ........................................................131 TOSHIBA Hardware Setup.....................................132 TOSHIBA Zooming Utility......................................
Contents 23 Contacting Toshiba .........................................157 Other Toshiba Internet Web sites..........................158 Toshiba’s worldwide offices..................................159 Appendix A: Hot Keys/TOSHIBA Cards ................................. 161 Hot Key Cards .......................................................161 Using the Hot Key Cards .................................162 Application Cards..................................................163 Using the Application Cards.
Introduction Welcome to the world of portable, multimedia computing. With your Toshiba computer, your entertainment can accompany you wherever you go. Using the installed wireless technology, you can check email, enjoy streaming music or video, make calls with VOIP (Voice Over IP), or stay up-to-date with your favorite Web pages. Your computer model may be ENERGY STAR® qualified.
Introduction 25 According to the EPA, a computer meeting the new ENERGY STAR® specifications will use between 30% and 60% less energy depending on how it is used. If all U.S. households and businesses replaced old computers with new ENERGY STAR® qualified models, we would save more than $2 billion in energy costs each year and avoid greenhouse gas emissions equivalent to nearly 3 million cars.
Introduction This guide NOTE The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba’s Web site at pcsupport.toshiba.com.
Introduction Safety icons 27 Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Introduction Other documentation Your computer’s features and specifications Certain computer chassis are designed to accommodate all possible configurations for an entire product Series. Your select model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis, unless you have selected all those features. This information applies to all the features and icons described in this guide.
Chapter 1 Getting Started This chapter provides tips for using your computer effectively, summarizes how to connect components, and explains what to do the first time you use your computer. The “Instruction Manual for Safety and Comfort,” that is shipped with your computer, contains important safety information.
Getting Started Getting comfortable with your computer To keep your computer in prime operating condition, protect your work area from: ❖ Dust, moisture, and direct sunlight. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ❖ Extreme heat, cold, or humidity.
Getting Started Getting comfortable with your computer ❖ ❖ 31 Avoid prolonged physical contact with the underside or surface of the computer. Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injury to skin. Read the “Avoid extended contact between computer base/palm rest and skin” section in the “Instruction Manual for Safety and Comfort” that is shipped with your computer.
Getting Started Setting up your computer Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep mode).
Getting Started Connecting to a power source NOTE 33 Please handle your computer carefully to avoid scratching or damaging the surface. Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery. Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly.
Getting Started Connecting to a power source To connect AC power to the computer: 1 Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. _ + 2 Plug the AC adaptor cord into the DC-IN on the side of the computer.
Getting Started Charging the main battery 35 The computer’s main battery light gives you an indication of the main battery’s current charge: NOTE ❖ Glows amber while the main battery is being charged (AC adaptor connected) ❖ Glows green when the main battery is fully charged ❖ Is unlit when the main battery has discharged, the battery is not charging, or the AC adaptor is not plugged into the computer or AC outlet ❖ Flashes amber when the main battery charge is low and it is time to recharge the
Getting Started Using the computer for the first time NOTE Battery life and charge time may vary depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Facing the front of the computer, locate the center of the display panel. 2 Gently raise the panel. 3 Adjust the display to a comfortable viewing angle.
Getting Started Using the computer for the first time 37 Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate.
Getting Started Registering your computer with Toshiba Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. NOTE The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices. The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software. Follow the on-screen instructions.
Getting Started Adding memory (optional) ❖ 39 Connect an optional external optical disc drive Adding memory (optional) HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com. Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data.
Getting Started Adding memory (optional) If the computer is on, begin at step 1; otherwise, skip to step 3. 1 Click Start. Start button Shut down button (Sample Image) Shut down button 2 Click the Shut down button in the lower-right corner of the Start menu. The computer closes all open programs, shuts down the operating system, and then turns off. 3 Unplug and remove any cables connected to the computer, including the AC adaptor.
Getting Started Adding memory (optional) 6 41 Using a small Phillips screwdriver, loosen the captive screw that secures the memory module slot cover. Back of computer (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cover. 8 Place the screw and the cover in a safe place so that you can retrieve them later. Static electricity can damage the memory module.
Getting Started Adding memory (optional) 11 Locate the empty memory module slot on the underside of the computer. 12 Pick up the memory module by its sides, avoiding any contact with its connector. Position the module toward the socket, aligning the connector’s notch with the matching key in the socket.
Getting Started Adding memory (optional) 43 14 Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module. If the latches and cutouts do not line up correctly, repeat steps 13-14.
Getting Started Adding memory (optional) 16 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 106. 17 Turn the computer right side up. Make sure to remove the soft cloth from the work surface before restarting the computer.
Getting Started Adding memory (optional) 45 Removing a memory module If you need to remove a memory module: 1 Complete steps 1–8 in “Installing a memory module” on page 39 to shut down the computer and open the memory module slot cover. Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory module. Do not remove the memory module while the computer is in Sleep or Hibernation mode.
Getting Started Adding memory (optional) 3 Gently lift the memory module to a 30-degree angle and slide it out of the slot. Memory slot Back of computer (Sample Illustration) Removing the memory module 4 Replace the memory module slot cover and secure it using the screw. 5 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 106. 6 Turn the computer right side up.
Getting Started Recovering the Internal Storage Drive 7 Reconnect the cables. 8 Restart the computer. 47 TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory module, you can check that the computer has recognized the change. To do this: ❖ Click Start, Control Panel, System and Security, and then System. The System window appears. Installed memory (RAM) is displayed below the System heading.
Getting Started Recovering the Internal Storage Drive The following internal storage drive recovery options are available: Recovery option Description Recover to out-of-box This option restores the original factory image to your state internal storage drive, returning your computer to its out-of-box state. (Recommended recovery method) Recover to a custom size partition See “Recovering to out-of-box state (recommended recovery method)” on page 49.
Getting Started Recovering the Internal Storage Drive NOTE 49 ❖ During the internal storage drive recovery process it is strongly recommended that your computer be connected to an external power source via the AC adaptor. ❖ The Toshiba Recovery Wizard also provides the option of erasing your internal storage drive, without restoring the information on the drive. See “Erasing the Internal Storage Drive” on page 61 for more information.
Getting Started Recovering the Internal Storage Drive 3 A warning screen appears, stating that when the recovery is executed all data will be deleted and rewritten. Click Yes to continue. (Sample Image) Warning screen 4 When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next.
Getting Started Recovering the Internal Storage Drive 5 51 The Recovery of Factory Default Software screen appears. Select Recover to out-of-box state. (Sample Image) Recovery of Factory Default Software screen 6 Click Next. A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to save your work to external media before proceeding (see “Backing up your work” on page 92). 7 Click Next to begin the recovery.
Getting Started Recovering the Internal Storage Drive The “Recover to a custom size partition” option restores your C: drive to its out-of-box state, and allows you to specify the size for the C: partition. You can resize and recover the C: drive using the utilities stored on your computer’s internal storage drive or using recovery DVDs/media, if you have created such media. To recover using the first method, follow the procedure below.
Getting Started Recovering the Internal Storage Drive 53 (Sample Image) Selecting a Process screen 5 The Recovery of Factory Default Software screen appears. Select Recover to a custom size partition. (Sample Image) Recovery of Factory Default Software screen 6 Use the on-screen arrow buttons in The size of drive C: field to set the partition size.
Getting Started Recovering the Internal Storage Drive 7 Click Next. A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to save your work to external media before proceeding (see “Backing up your work” on page 92). 8 Click Next to begin the recovery. When the process is complete, a message displays indicating that the C: drive has been recovered. 9 Press any key on the keyboard to restart the computer.
Getting Started Recovering the Internal Storage Drive 3 55 A warning screen appears stating that when the recovery is executed all data will be deleted and rewritten. Click Yes to continue. (Sample Image) Warning screen 4 When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next.
Getting Started Recovering the Internal Storage Drive 5 The Recovery of Factory Default Software screen appears. Select Recover without changing the hard drive partitions. (Sample Image) Recovery of Factory Default Software screen 6 Click Next. A confirmation message displays reminding you that all data on the C: drive will be lost during the recovery process. Be sure to save your work to external media before proceeding (see “Backing up your work” on page 92). 7 Click Next to begin the recovery.
Getting Started Recovering the Internal Storage Drive NOTE 57 When you create recovery DVDs/media, only the operating system files, applications, and drivers originally shipped with the computer are backed up to the external media and can be restored from this media. Any files that you created are not backed up on the recovery DVDs/media. You will need to separately back up the files you created; for more information, see “Backing up your work” on page 92.
Getting Started Recovering the Internal Storage Drive 2 Select DVD or USB Flash from the drop-down lists next to “System Recovery Media” and “Application Discs,” depending on the type of external media you want to use. NOTE You cannot store your system’s applications on the same drive or disc/disc set where the rest of the system recovery files are stored. For example, you will need to store the applications on one USB flash drive and the system recovery files on another USB flash drive.
Getting Started Recovering the Internal Storage Drive 59 Restoring from recovery DVDs/media The recovery process deletes information stored on the internal storage drive. Be sure to save your work to external media before executing the recovery (see “Backing up your work” on page 92). NOTE During the internal storage drive recovery process it is strongly recommended that your computer be connected to an external power source via the AC adaptor.
Getting Started Recovering the Internal Storage Drive 2 3 Do one of the following: ❖ If your recovery files are on DVDs, insert the first recovery DVD into your optional external writable optical disc drive. Consult the documentation that came with your optical disc drive to learn how to load the DVD while the computer is powered off. ❖ If your recovery files are on a USB flash drive, connect the USB flash drive to your computer. Turn on your computer. When the initial screen displays, press F12.
Getting Started Erasing the Internal Storage Drive 61 Erasing the Internal Storage Drive Erasing the internal storage drive will delete all data on the drive, including the partitions. Be sure to create recovery DVDs/media and back up your data to external media before erasing the internal storage drive. NOTE If you want to restore the internal storage drive, use one of the recovery options instead of erasing the drive. For more information, see “Recovering the Internal Storage Drive” on page 47.
Getting Started Checking the internal storage drive operating status (Sample Image) Erase the hard disk screen 4 Click Next. A confirmation message displays reminding you that all data on the internal storage drive will be lost. Be sure you have saved your work to external media (see “Backing up your work” on page 92) and created recovery DVDs/media (see “Creating recovery DVDs/media” on page 56) before proceeding. 5 Click Next to begin erasing the internal storage drive.
Getting Started Using the TouchPad™ 63 Installing drivers and applications The Toshiba Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: 1 Click Start, All Programs, My Toshiba, and then TOSHIBA Application Installer. 2 Click Next. 3 Click the item you want to install. 4 Click Install. 5 Follow the on-screen prompts to complete the installation process.
Getting Started Using the TouchPad™ Refer to the table below for specific instructions on performing each operation. NOTE To: The pointer is the icon (usually an arrow) that moves on the screen when you slide your finger across the TouchPad or move a mouse connected to your computer. Do the following: Example: Move the on-screen Slide your finger across the TouchPad in the direction you want to move the pointer.
Getting Started Using the TouchPad™ To: Do the following: Scroll vertically Slide your finger along the right edge of the TouchPad in the direction you want to scroll. Repeat to scroll a longer distance. 65 Example: (Sample Illustration) Vertical scrolling active area Scroll horizontally Slide your finger along the bottom edge of the TouchPad in the direction you want to scroll. Repeat to scroll a longer distance.
Getting Started Using the TouchPad™ To: Do the following: Zoom in/out To zoom in: ❖ Place two fingers close together on Example: the TouchPad and then slide them apart. To zoom out: ❖ Place two fingers slightly apart on the TouchPad and then slide them together. (Sample Illustration) Zooming in (Sample Illustration) Zooming out Adjusting TouchPad™ settings While you are typing, the on-screen pointer may seem to move or jump around “by itself” to random locations on the screen.
Getting Started Using external display devices NOTE 67 TouchPad setting options vary by computer model. The TouchPad settings are accessible through the Mouse Properties option of the Windows Control Panel. For more information, please visit www.support.toshiba.com, and enter the phrase “Mouse pointer jumps around as you type” into the Search field. Disabling or enabling the TouchPad™ The TouchPad™ is enabled by default. To enable/disable the TouchPad, press Fn + F9.
Getting Started Using external display devices Directing the display output when you turn on the computer Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. NOTE Some modes are only available with the appropriate device attached and turned on. The quickest way to change the display output settings is to use the display hot key (Fn + F5): 1 Press Fn and F5 simultaneously.
Getting Started Using an external keyboard 69 Adjusting the quality of the external display To obtain the best picture quality from your monitor (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps. Using an external keyboard If you prefer to use an external keyboard, you can attach one to your computer. The computer’s USB ports support most USB-compatible keyboards.
Getting Started Connecting a printer If your printer does not support Plug and Play, you can set up the printer as described in “Setting up a printer” on page 70. To connect a printer to your computer: 1 Connect the printer cable to the printer and then connect the other end to one of the computer’s USB ports. 2 Plug the printer’s power cable into a live AC outlet. Setting up a printer NOTE Some printers require a specific installation process.
Getting Started Turning off the computer 71 Turning off the computer Pressing the power button before shutting down the Windows® operating system could cause you to lose your work. Make sure the system indicator panel’s storage drive light and the drive in-use light are off. If you turn off the power while a disk/disc is being accessed, you may lose data or damage the disk/disc and/or drive. It is a good idea to turn off your computer when you are not using it for a while.
Getting Started Turning off the computer Hibernation mode Hibernation mode shuts the computer down completely, but it first saves the current state of the computer to the internal storage drive. Since Hibernation mode does not require power to maintain the saved information, system settings are retained indefinitely. Factors to consider when choosing Hibernation: ❖ While in Hibernation mode, the computer uses no main battery power.
Getting Started Turning off the computer 73 ❖ Restarting from Sleep takes less time and consumes less main battery power than restarting after turning off the computer using the Hibernation or Shut down commands. ❖ When starting up again, the computer returns to the mode in which you left it, including all open programs and files you were using. ❖ If the battery charge becomes critically low, the computer will try to enter Hibernation mode.
Getting Started Turning off the computer Turning off the computer more quickly You can also turn off the computer by pressing the power button. To use this method, you first need to activate it using the Power Options feature. By default, pressing your computer’s power button puts the computer into Sleep mode. 1 Click Start, Control Panel, System and Security, and then Power Options. The Power Options window appears. 2 Click Change plan settings under the power plan to be customized.
Getting Started Turning off the computer 4 75 Double-click Power buttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of Power Options screen 5 Select the options you want from the drop-down lists. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power.
Getting Started Turning off the computer Restarting your computer To start the computer up again, press the power button until the ON/OFF light glows green. If you turn off the computer by closing the display panel, you can start it again by opening the display panel. Using and configuring Hibernation mode To turn off the computer using the Hibernation command: 1 Click Start, and then click the arrow next to the Shut down button in the lower-right corner of the Start menu.
Getting Started Turning off the computer 2 77 Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. (Sample Image) Edit Plan Settings screen 3 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. 4 Double-click Power buttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of Power Options screen 5 Select Hibernate for the options you want.
Getting Started Turning off the computer NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power. ❖ Lid close action Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel. ❖ Power button action Set this option to Hibernate if you want the computer to go into Hibernation mode when you press the power button. 6 Click Apply. 7 Click OK.
Getting Started Turning off the computer 2 79 Click Sleep in the pop-up menu. The computer saves the status of all open programs and files to the memory, turns off the display, and enters into a low-power mode. The ON/OFF light blinks amber indicating the computer is in Sleep mode. Configuring Sleep mode options You can place the computer into Sleep mode by either pressing the power button or closing the display panel.
Getting Started Turning off the computer 4 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. 5 Double-click Power buttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of Power Options screen 6 Select Sleep for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power.
Getting Started Customizing your computer’s settings 81 Starting again from Sleep mode To start up the computer from Sleep mode, press the power button until the ON/OFF light glows green. The computer returns to the screen(s) you were using. If you place the computer in Sleep mode by closing the display panel, you can start it again by opening the display panel. Closing the display panel After you have turned off the computer, close the display panel to keep dust and dirt out of the computer.
Getting Started Caring for your computer Moving the computer Before moving your computer, even across the room, make sure all drive activity has ended (the internal storage drive and optical disc drive indicator lights stop glowing) and all external peripheral cables are disconnected. Do not pick up the computer by its display panel or by the back. Doing so could damage the system. Using a computer lock You may want to secure your computer to a heavy object such as your desk.
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the internal storage drive. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Learning the Basics Using the keyboard ❖ Back up your files to external media on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your internal storage drive suddenly fails, you will lose all the data on it unless you have a separate backup copy. For more information, see “Data and system configuration backup in the Windows® operating system” on page 153.
Learning the Basics Using the keyboard 85 Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The space bar creates a space character instead of just passing over an area of the page. ❖ The lowercase letter l (el) and the number 1 are not interchangeable. ❖ The uppercase letter O and the number 0 are not interchangeable.
Learning the Basics Using the keyboard F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, function keys marked with icons execute specific functions on the computer. For example, Fn + F9 turns the TouchPad™ ON/OFF. For more information, see “Hot key functions” on page 165.
Learning the Basics Starting a program 87 Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys. To turn the numeric overlay on, press Fn and F11 simultaneously. The numeric overlay light on the system indicator panel glows when the numeric overlay is on. To disable the numeric overlay, hold down the Fn key and press F11 again. The numeric overlay light on the system indicator panel goes out.
Learning the Basics Starting a program Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows® WordPad program as an example: 1 Click Start, and then All Programs. The Windows® operating system displays the All Programs menu, which lists programs and program groups.
Learning the Basics Starting a program 4 89 In the right part of the window, double-click the folder containing the program, in this case Program Files. Windows® Explorer shows the contents of the Program Files folder on the right side of the window. 5 In the right part of the window, double-click Windows NT. 6 In the right part of the window, double-click Accessories. Windows® Explorer shows the contents of the Accessories folder on the right side of the window.
Learning the Basics Saving your work Saving your work Before you turn off the computer using the Shut down command, save your work on the internal storage drive, external media, flash media, or optical disc. This is one of the most important rules of computing. When you turn off the computer using the Sleep or Hibernate commands, your work should be there when you resume. Many programs offer a feature that saves documents at regular intervals.
Learning the Basics Printing your work 91 File names The Windows® operating system supports long file names that can contain up to 260 characters and can include spaces. Some applications do not support long file names and require file names limited to no more than eight characters. You may use all the letters, numbers, and other characters on the keyboard, except for these characters: \ / ? : * " > < |. File names are not case-sensitive.
Learning the Basics Backing up your work 2 Click on the arrow in the upper-left corner of your Windows®-based application to display the drop-down menu, and then click Print. The program displays a Print dialog box. (Sample Image) Print dialog box 3 Specify the print parameters. For example, the range of pages and number of copies to print. 4 Click Print. Backing up your work Back up all the files you create in case something happens to your computer.
Learning the Basics Toshiba’s online resources 93 Restoring your work To restore information from your backup media to your internal storage drive, use the Restore option in the Windows® Backup and Restore program. Look in the online Help or your operating system documentation for information on restoring files. (Sample Image) Backup and Restore screen TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the internal storage drive.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been preset by Toshiba.
Mobile Computing Running the computer on battery power 95 Battery Notice Battery life rating is for comparison purposes only, and does not indicate the battery life that will be obtained by any individual user. Actual battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components.
Mobile Computing Charging batteries TECHNICAL NOTE: Depending on your system, the RTC battery may only charge while the computer is turned on. Power management Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes. Changes to these settings may result in system performance or stability issues.
Mobile Computing Charging batteries 97 Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet. The battery charges whether the computer is on or off. TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices.
Mobile Computing Monitoring main battery power To recharge the RTC battery, plug the computer into a live electrical outlet and leave the computer powered on for 24 hours. NOTE It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working.
Mobile Computing Monitoring main battery power HINT: Be careful not to confuse the battery light ( ON/OFF light ( ). ) with the When the ON/OFF light flashes amber, it indicates that the system is suspended (using the Windows® operating system Sleep command).
Mobile Computing Monitoring main battery power Determining remaining battery power NOTE Wait a few moments after turning on the computer before trying to monitor the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform its calculations. Move the pointer over the power icon in the notification area, see “Finding your way around the desktop” on page 112 for more information on the notification area.
Mobile Computing Monitoring main battery power 101 Setting battery notifications You can set two notifications. Each notification can be set to alert you when a specified percentage of remaining battery power has been reached. You can also set the computer to enter Sleep mode or Hibernation mode or to completely power down when the notification goes off. To change the default notification settings: 1 Click Start, Control Panel, System and Security, and then Power Options.
Mobile Computing Monitoring main battery power ❖ How much you use the internal storage drive or other optional devices ❖ Where you are using the computer, since operating time decreases at low temperatures There are various ways in which you can conserve power and extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves power when you turn off the computer and turn it back on again ❖ Use the Windows® power-saving option plans These power-saving options control the
Mobile Computing Monitoring main battery power 103 2 Select an appropriate plan for your work environment or create your own custom plan. 3 Click Create a power plan in the left pane to set up a new plan. NOTE 4 To edit a plan or to edit advanced settings, continue to the following steps. Click Change plan settings to choose the plan you want to edit. This screen allows you to change basic settings.
Mobile Computing Changing the main battery 2 While continuing to press Fn, press F2 until you select the desired Power Plan. The Power Plan options are: Balanced and Power Saver. 3 Release the Fn key. The hot key card disappears. You are now in the selected mode. Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery.
Mobile Computing Changing the main battery 5 105 Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock 6 Slide the battery release latch to release the battery. 7 Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
Mobile Computing Changing the main battery Inserting a charged battery To insert a battery: 1 Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks. The battery pack has been designed so that you cannot install it with reverse polarity. If the battery does not slide into the slot easily, move the battery release lock to the unlocked position and try again. Do not force the battery into position.
Mobile Computing Taking care of your battery 107 5 Reconnect any cables that were removed in step 3 of “Removing the battery from the computer” on page 104. 6 Restart the computer. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life.
Mobile Computing Taking care of your battery Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: 1 Turn off the computer’s power. 2 Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on, go to step 4.
Mobile Computing Disposing of used batteries 109 Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you have fully recharged the battery. You must discard a battery if it becomes damaged. Never attempt to dispose of a battery pack by burning or by throwing it into a fire, and never allow exposure to a heating apparatus (e.g., microwave oven).
Mobile Computing Traveling tips Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle™, a program of the Rechargeable Battery Recycling Corporation. For more information and for drop-off locations, visit www.rbrc.org or call 1-800-822-8837. Notice regarding CR coin cell batteries, applicable to California, U.S.A. only: Perchlorate Material - special handling may apply. See http://www.dtsc.ca.
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows® operating system. You can use its features to start programs, find documents, set up system components, and perform most other computing tasks. HINT: The illustrated examples in this guide may appear slightly different from the screens displayed by your system.
Exploring Your Computer’s Features Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, notification area, and background pattern. Icons Start button Taskbar Notification area (Sample Image) Windows® operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Exploring Your Computer’s Features Exploring the desktop 113 ❖ TECHNICAL NOTE: If you delete a large number of files or very large files from the internal storage drive, there may be insufficient space available in the Recycle Bin to hold these files. In this case, Windows® will prompt you to either permanently delete the file(s) or cancel the deletion. ❖ If you delete a file (of any size) from an external media or flash media, it does not go into the Recycle Bin. The file is permanently deleted.
Exploring Your Computer’s Features Setting up for communications To make a program or window the currently active one, click the associated taskbar button. Notification area The notification area displays icons of tasks or programs that run continuously in the background and displays notifications. To learn more about each task, position the pointer over the icon for a few moments and a short description of the task appears.
Exploring Your Computer’s Features Exploring audio features NOTE 115 When the Wireless antenna is ON, the wireless indicator light be lit. will For help with common Wi-Fi® networking problems, see “Wireless networking problems” on page 151. Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality using one of its communication ports.
Exploring Your Computer’s Features Exploring audio features 3 Click the Start Recording button. 4 Speak normally into the microphone. NOTE 5 For better sound quality, you may need to speak closer to the internal microphone. When you have finished recording, click the Stop Recording button. The Save As dialog box appears. 6 To save the file, type a file name, and then click Save.
Exploring Your Computer’s Features Using the Web Camera 117 Using the Web Camera Your computer may come with a built-in Web Camera. With this Web Camera you can do the following: ❖ Take pictures and record videos with your computer ❖ Chat with others and have them see you while using instant messaging (IM) programs ❖ Have video conference calls NOTE To email, instant message or video conference, you must be connected to the Internet.
Exploring Your Computer’s Features Using the Memory card reader Inserting memory media The following instructions apply to all types of supported media devices. 1 Turn the media so that the contacts (metal areas) are face down. 2 Push the media into the adapter until it locks in place. (Sample Illustration) Inserting memory media When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data.
Exploring Your Computer’s Features Using the Memory card reader 3 119 Grasp the card and pull it straight out. (Sample Illustration) Removing memory media Do not remove memory media while data is being written or read. Even when the Windows® message “copying...” disappears, writing to the media might still be in progress and your data could be destroyed. Wait for the indicator light to go out.
Chapter 5 Utilities Your computer includes several utilities designed to help you to reconfigure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter. NOTE 120 The utilities described in this chapter, and the icons shown in the sample images are applicable only if the related utility is available on your system.
Utilities TOSHIBA Assist 121 TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, click Start, All Programs, TOSHIBA, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears.
Utilities TOSHIBA Assist Secure The features available in this category are: ❖ Supervisor password ❖ User password (Sample Image) TOSHIBA Assist window – Secure tab
Utilities TOSHIBA Assist 123 Protect & Fix The feature available in this category is: ❖ TOSHIBA PC Diagnostic Tool Utility (Sample Image) TOSHIBA Assist window – Protect & Fix tab
Utilities TOSHIBA Assist Optimize The features available in this category are: ❖ Mouse Utility ❖ TOSHIBA Hardware Setup (Hardware Settings) ❖ TOSHIBA Zooming Utility ❖ TOSHIBA Accessibility (Sample Image) TOSHIBA Assist window – Optimize tab
Utilities TOSHIBA Recovery Media Creator 125 TOSHIBA Recovery Media Creator The TOSHIBA Recovery Media Creator utility enables you to create recovery DVDs/media that can be used to return your system to its out-of-box state, if necessary. For detailed information on using the utility to create recovery DVDs/media, see “Creating recovery DVDs/media” on page 56.
Utilities Setting passwords Setting passwords Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can work on your computer again. TOSHIBA supports several types of passwords on your computer: ❖ NOTE An instant password—Secures your open programs and files when leaving the computer temporarily.
Utilities Setting passwords 127 Using a supervisor password A supervisor password prevents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, TOSHIBA strongly recommends that you save your password in a location where you can later access it should you not remember it. TOSHIBA is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your computer.
Utilities Setting passwords 6 Click OK. The supervisor password utility dialog box appears. 7 Select Able to run HWSetup or Unable to run HWSetup and then Click OK. 8 Restart the system to complete the process. Deleting a supervisor password To delete a supervisor password: 1 Click Start, All Programs, TOSHIBA, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears. 2 On the left side, click the Secure tab. 3 Click the Supervisor Password icon.
Utilities Setting passwords 129 To register a password for the power-on password functions: 1 Click Start, All Programs, TOSHIBA, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears. 2 On the left side, click the Secure tab. 3 Click the User Password icon. 4 Click Registered. 5 Enter your password, and then enter it again to verify. 6 Click OK. 7 Click OK to exit.
Utilities TOSHIBA PC Diagnostic Tool Utility TOSHIBA PC Diagnostic Tool Utility This utility can help diagnose problems with devices in your computer. Refer to the online Help documentation within the application for additional help. NOTE The TOSHIBA PC Diagnostic Tool utility may show tests for features you do not have. This is normal and does not indicate a problem.
Utilities Mouse Utility 131 Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. To access the Mouse utility: 1 Click Start, Control Panel, Hardware and Sound, and then under Devices and Printers, click Mouse, or click the Mouse icon in the Optimize tab of TOSHIBA Assist. The Mouse Properties screen appears.
Utilities TOSHIBA Hardware Setup TOSHIBA Hardware Setup TOSHIBA Hardware Setup is the TOSHIBA configuration management tool available through the Windows® operating system. To access it: ❖ Click Start, All Programs, TOSHIBA, Utilities, and then HWSetup, or click the TOSHIBA Hardware Settings icon in the Optimize tab of TOSHIBA Assist. The TOSHIBA HWSetup screen appears.
Utilities TOSHIBA Hardware Setup 133 ❖ Display—Allows you to change various default settings for the built-in display NOTE When the computer restarts, it remembers the last configuration. If data does not appear on the display you are using after starting in Sleep mode, press Fn + F5. For more information, see “Directing the display output when you turn on the computer” on page 68.
Utilities TOSHIBA Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot keys (see “Zoom (Display resolution)” on page 174).
Utilities TOSHIBA Accessibility 135 TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the Fn key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sticky key, meaning you can press it once, release it, and then press a function key to activate the hot key function.
Utilities TOSHIBA Service Station TOSHIBA Service Station The TOSHIBA Service Station helps you keep your new computer running at its best by notifying you when updated software, firmware, documentation or other information is available for your computer. The TOSHIBA Service Station will alert you when updates are available, and you can then choose to install the updates if you wish.
Chapter 6 If Something Goes Wrong Some problems you may encounter when using your computer are relatively easy to identify and solve. Others may require help from your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
If Something Goes Wrong Problems when you turn on the computer 2 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with the next step. 4 Close the remaining programs one by one by selecting the program name, then End Task.
If Something Goes Wrong Problems when you turn on the computer 139 The computer displays the WARNING RESUME FAILURE/Windows Error Recovery – Windows did not shut down successfully message. To continue, select Start Windows normally. This can happen if the computer was put into Sleep mode and the battery has discharged. If you performed a shutdown before this message was displayed, a program or driver may have prevented Windows® from shutting down. Data stored in the computer’s memory has been lost.
If Something Goes Wrong The Windows® operating system is not working If the trickle-charging does not prove effective, visit the Toshiba Web site at pcsupport.toshiba.com and see the Support Bulletin Step-Charging the computer’s battery (click the Ask Iris® link and search for the support bulletin by name). 4 Connect the AC adaptor to a different power outlet, preferably in a different room.
If Something Goes Wrong ® The Windows operating system is not working 141 ❖ The operating system responds differently from the normal routine. ❖ The screen does not look right. Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device. If you experience any of these problems, use the options in the Startup menu to fix the problem.
If Something Goes Wrong The Windows® operating system is not working NOTE If your computer is connected to a network, the Startup menu may display different versions of Safe mode. Internet problems My Internet connection is very slow. Many factors contribute to the speed with which you can surf the Internet. They include: network speed, network conditions, time of day (when everyone else is surfing, your access can be slow) and popularity of the sites you are trying to access.
If Something Goes Wrong Fixing a problem with Device Manager 143 Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable. Device Manager is a configuration tool for advanced users who understand configuration parameters and the ramifications of changing them.
If Something Goes Wrong Memory problems Memory problems Incorrectly connected or faulty memory modules may cause errors that seem to be hardware or even software related. It is worthwhile checking for these first: 1 Click Start, and then click the Shut down button in the lower-right corner of the Start menu. The computer shuts down completely. 2 Remove the memory module, following the instructions in “Removing a memory module” on page 45.
If Something Goes Wrong Power and the batteries 145 The AC adaptor and power cord/cable work correctly, but the battery will not charge. The battery does not charge while the computer is consuming full power. Try turning off the computer. The battery may not be inserted correctly in the computer. Turn off the computer, remove the battery, clean the contacts with a soft dry cloth (if necessary) and replace the battery. See “Removing the battery from the computer” on page 104.
If Something Goes Wrong Keyboard problems Keyboard problems If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itself. The keyboard produces unexpected characters. A keypad overlay may be on. If the numlock light or cursor control overlay light is on, press Fn + F10 to turn off the cursor control overlay light, or Fn + F11 to turn off the numlock light.
If Something Goes Wrong Display problems 147 If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’s power cord/cable is firmly plugged into a working power outlet. ❖ Check that the cable connecting the external monitor to the computer is firmly attached. ❖ Try adjusting the contrast and brightness controls on the external monitor. ❖ Press Fn and F5 simultaneously to make sure the display priority is not set for the built-in screen.
If Something Goes Wrong Disk or storage drive problems The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode, and not simultaneous mode. Small bright dots appear on your TFT display when you turn on your computer.
If Something Goes Wrong Sound system problems 4 5 6 7 149 Click the Tools tab. Click the Check now... button. The Check Disk box appears. You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors Click Start. Error-checking tests and repairs the storage drive. Your hard disk seems very slow. If you have been using your computer for a long time, your files may have become fragmented. Run Disk Defragmenter.
If Something Goes Wrong Printer problems Printer problems This section lists some of the most common printer problems. The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray. Make sure the printer cable is firmly attached to the computer and the printer.
If Something Goes Wrong Wireless networking problems 151 Wireless networking problems NOTE This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi®) networking. The terms and concepts used assume a basic understanding of networks, and may be for more advanced users. If you need assistance or if you are not familiar with the terminology, please see Windows® Help and Support or contact your computer technician.
If Something Goes Wrong Develop good computing habits ❖ Use IPCONFIG to verify that the computer has a useful IP address - one other than the private address of 169.254.xxx.xxx assigned by Windows®. 1 Click Start to open the Start menu. 2 Type Cmd in the Search programs and files field. 3 Enter IPCONFIG /ALL and press Enter. The IP address for each active network adapter will be displayed.
If Something Goes Wrong Develop good computing habits 153 On a regular basis, back up the information stored on your internal storage drive. Here are some ways you can do this: ❖ Copy files to an external storage device. ❖ Connect an optional external optical disc drive to the system and use specialized software to copy everything on the internal storage drive to an optical disc. ❖ Connect your computer to the office network and copy files to your network partition.
If Something Goes Wrong Develop good computing habits Saving system configuration with restore points The System Restore feature of the Windows® operating system quickly creates restore points - ‘snapshots’ of your Windows® operating system configuration - and saves them for later recall.
If Something Goes Wrong Develop good computing habits NOTE 155 This list may contain restore points that you did not create. Restore points labeled System Checkpoint were automatically created by the Windows® operating system. Other restore points may have been created automatically by applications when they were installed. 3 If you selected Choose a different restore point in step 2, select the restore point you want to use, and then click Next.
If Something Goes Wrong Develop good computing habits 4 Click Back up your computer under the System and Security heading. Follow the on-screen instructions to back up your files. For more help, click Start, Help and Support, and search for “back up files.” General tips for installing hardware and software Here are a few tips to help ensure safe and easy installation of new hardware (printers, pointing devices, external hard drives, DVD writers, scanners, etc.
If Something Goes Wrong If you need further assistance 3 4 5 6 157 Install one item of hardware or software. Restart the Windows® operating system. Use the new hardware or software for a while, noting any new problems. Make sure that your critical applications (email, business applications, etc.) are working correctly, and verify that important devices are still functioning.
If Something Goes Wrong Other Toshiba Internet Web sites Toshiba’s Technical Support Web site For technical support, or to stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com.
If Something Goes Wrong Toshiba’s worldwide offices 159 Toshiba’s worldwide offices Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road North Ryde NSW 2113 Sydney Australia Canada Toshiba Canada Ltd. 191 McNabb Street Markham, Ontario L3R - 8H2 Canada France Toshiba Systèmes (France) S.A. 7, Rue Ampère; B. P.
If Something Goes Wrong Toshiba’s worldwide offices United States Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States The Rest of Europe Toshiba Europe (I.E.) GmbH Hammfelddamm 8 D-4-1460 Neuss Germany For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm.
Appendix A Hot Keys/TOSHIBA Cards Hot keys and TOSHIBA Cards provide a quick way to modify selected system functions and to launch applications. There are two types of TOSHIBA Cards: Hot Key Cards and Application Cards. Hot Key Cards The Hot Key Cards are used to set or modify the following system functions: ❖ Mute ❖ Lock (Instant security) ❖ Power Plan ❖ Sleep ❖ Hibernation ❖ Output (Display switch) ❖ Brightness control ❖ Wireless ❖ TouchPad™ ❖ Zoom (Display resolution) 161 5.
Hot Keys/TOSHIBA Cards Hot Key Cards Using the Hot Key Cards The Hot Key Cards are normally hidden from view. The Cards appear when you press the Fn key. NOTE Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls. To use the Hot Key Cards: 1 Press and hold the Fn key. The TOSHIBA Cards appear along the top of the screen.
Hot Keys/TOSHIBA Cards Application Cards 163 Application Cards The Application Cards are used to launch these applications: TOSHIBA Assist For more information, refer to “TOSHIBA Assist” on page 121. PC Diagnostic Tool Utility For more information, refer to “TOSHIBA PC Diagnostic Tool Utility” on page 130. TOSHIBA Zooming Utility For more information, refer to “TOSHIBA Zooming Utility” on page 134. TOSHIBA Hardware Setup Utility For more information, refer to “TOSHIBA Hardware Setup” on page 132.
Hot Keys/TOSHIBA Cards Application Cards 2 Click the “stacked” card on the far right of the display. The Application Cards are hidden under this card. The Application Cards appear, and the Hot Key Cards are stacked under the Card on the far left. (Sample Image) Application Card display 3 Click the Card for the application Card to appear. 4 Click the full-size Card to launch the application.
Hot Keys/TOSHIBA Cards Hot key functions 165 Hot key functions Hot key functions are performed using either the Hot Key Cards or by pressing the associated hot key. This section lists the available hot key functions. NOTE Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls. Volume Mute This TOSHIBA Card or hot key enables/disables volume mute on your computer.
Hot Keys/TOSHIBA Cards Hot key functions Lock (Instant security) This TOSHIBA Card or hot key blanks the display. Selecting this Card or pressing the hot key displays the following options: or Fn + (Sample Image) Security options ❖ To enable lock, select ❖ To cancel, select . . The Fn + F1 hot key function activates instant security. The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions 167 Power plan This TOSHIBA Card or hot key displays the power plans and cycles through the power plans. or Fn + The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options window. Selecting this Card or pressing the hot key displays the currently selectable power plans: (Sample Image) Power Plan options Cycle through the power plans, then select the desired power plan. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions Sleep mode This TOSHIBA Card or hot key places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mode” on page 78. or Fn + Selecting this Card or pressing the hot key displays the following options: (Sample Image) Sleep options ❖ To enable Sleep mode, select ❖ To cancel, select 5.375 x 8.375 ver 2.3 . .
Hot Keys/TOSHIBA Cards Hot key functions Hibernation mode This TOSHIBA Card or hot key places the computer into Hibernation mode. or Fn + If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 76. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Hibernation options ❖ To enable Hibernation mode, select ❖ To cancel, select 5.375 x 8.375 ver 2.3 . .
Hot Keys/TOSHIBA Cards Hot key functions Output (Display switch) or This TOSHIBA Card or hot key cycles through the power-on display options (only the first option is available when you do not have an external monitor attached) (the last option is available only if you are in Extended Display Mode). NOTE Fn + Some modes are only available with the appropriate device attached and turned on.
Hot Keys/TOSHIBA Cards Hot key functions 171 Cycle through the display modes, then select the desired mode. Not all functions are supported on all models. NOTE Some systems also support an additional Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-in Display and External Monitor, or Built-in Display and TV). In extended desktop mode, the image is split into two sides, one side per display device. To swap sides, select Swap Image Display.
Hot Keys/TOSHIBA Cards Hot key functions Disabling or enabling wireless devices This TOSHIBA Card or hot key enables/disables the optional wireless devices installed in your computer. The available wireless mode is: or Fn + ❖ Wi-Fi® enabled—Enables just the Wi-Fi® module. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Wireless communication options ❖ To enable Wi-Fi®, select ❖ To cancel, select NOTE . .
Hot Keys/TOSHIBA Cards Hot key functions 173 Disabling or enabling the TouchPad™ This TOSHIBA Card or hot key enables/disables the TouchPad™. For more information on using the TouchPad, see “Using the TouchPad™” on page 63. or Fn + Selecting this Card or pressing the hot key displays the following options: (Sample Image) Disable or Enable TouchPad options ❖ To enable the TouchPad, select . ❖ To disable the TouchPad, select . 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions Zoom (Display resolution) This TOSHIBA Card or hot key switches screen resolution. Selecting this Card or pressing the hot key displays the following options: or Fn + [Space bar] (Sample Image) Screen resolution options Cycle through the screen resolutions, then select the desired resolution. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions 175 Keyboard hot key functions Fn + This hot key turns the cursor control overlay on and off. Fn + This hot key turns the numeric overlay on and off. Fn + This hot key turns the scroll lock feature on and off. Fn + This hot key turns the TOSHIBA Zooming Utility to zoom out. Fn + This hot key turns the TOSHIBA Zooming Utility to zoom in. Fn + This hot key decreases the speaker volume. Fn + This hot key increases the speaker volume. 5.375 x 8.
Appendix B Power Cord/Cable Connectors Your computer ships with the correct power supply for the country of purchase. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA Canada UL approved CSA approved United Kingdom Europe VDA approved NEMKO approved BS approved Australia AS approved 176 5.375 x 8.375 ver 2.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide.
Glossary DOS Disk Operating System DPI Dots Per Inch DVD Digital Versatile (or Video) Disc DVD-ROM Digital Versatile (or Video) Disc Read-Only Memory EPROM Erasable Programmable Read-Only Memory FAT File Allocation Table FCC Federal Communications Commission GB gigabyte HDD Hard Disk Drive HTML Hypertext Markup Language IEEE Institute of Electrical and Electronics Engineers I/O Input/Output IRQ interrupt request ISP Internet Service Provider KB kilobyte LAN Local Area Netw
Glossary 179 SD Secure Digital SDRAM Synchronous Dynamic Random Access Memory SSD Solid State Drive TFT Thin Film Transistor USB Universal Serial Bus URL Uniform Resource Locator WAN Wide Area Network www World Wide Web Terms The following terms may appear in this user’s guide. A active-matrix display—A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology.
Glossary baud rate—The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second. BIOS (Basic Input/Output System)—Basic instructions, stored in read-only memory (ROM), containing the information the computer needs to check hardware and load the operating system when you start up the computer.
Glossary 181 Central Processing Unit (CPU)—The chip that functions as the “brain” of the computer. It takes information from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character—Any letter, number, or symbol you can use on the computer. Some characters are non-printing characters, such as a paragraph break in a word-processing program. A character occupies one byte of computer storage.
D Glossary default—The setting selected by a program when the user does not specify an alternative setting. device—A component attached to the computer. Devices may be external (outside the computer’s case) or internal (inside the computer’s case). Printers, disk drives, and modems are examples of devices. device driver—A program (called a “driver”) that permits a computer to communicate with a device.
Glossary 183 download—(1) In communications, to receive a file from another computer through a modem or network. (2) To send font data from the computer to a printer. See also upload. drag—To hold down the mouse button while moving the pointer to drag a selected object. In the Windows® operating system, this refers to the left mouse button, unless otherwise stated. driver—See device driver. DVD—An individual digital versatile (or video) disc. See also DVD-ROM.
Glossary file extension—The three characters following the period (pronounced “dot”) at the end of a file name. The extension indicates the type of file. Examples are .exe for program files and .hlp for help files. See also file name. folder—Also called directory. A container for organizing files saved to a disk. A folder is symbolized on screen by a graphical image (icon) of a file folder. A folder can contain files and other folders.
Glossary 185 hot swapping—The ability to add or remove devices from a computer while the computer is running and have the operating system automatically recognize the change. I icon—A small image displayed on the screen that represents a function, file, or program. interlaced—A method of refreshing a computer screen, in which only every other line of pixels is refreshed. Interlaced monitors take two passes to create a complete screen image. Compare non-interlaced. internal device—See device.
Glossary load—To move information from a storage device (such as a hard disk) into memory for processing. local area network—See LAN. logical drive—A section of a disk that is recognized by the operating system as a separate disk drive. A system’s logical drives may differ from its physical drives. For example, a single hard disk drive may be partitioned into two or more logical drives.
Glossary 187 non-interlaced—A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen. Compare interlaced. non-system disk—A disk for storing programs and data that cannot be used to start the computer. Compare system disk. O online—Available through the computer.
Glossary Plug and Play—Generally, refers to the computer’s ability to automatically configure itself to work with peripheral devices. When capitalized, refers to a standard that, when followed by a device manufacturer, allows a computer to configure itself automatically to work with the device. pointer—An icon (usually an arrow) that moves on the screen when you slide your finger across the TouchPad or move a mouse.
Glossary 189 restart—Synonymous with reboot. To reset the computer by reloading the operating system without turning the computer off. See also boot. RGB (Red, Green, Blue) monitor—A monitor that reproduces all colors by mixing red, green, and blue light in various combinations. RJ11 connector—A modular connector used on most U.S. telephone systems and direct-connect modems. The RJ11 connector is a 6-wire connector. RJ45 connector—An eight-wire connector used to connect a computer to a network.
Glossary Suspend—A feature of some Windows® operating systems that allows you to turn off the computer without exiting your open applications and to continue from where you left off when you turn the computer on again. system prompt—The symbol (in the MS-DOS® operating system, generally a drive letter followed by a “greater than” sign) indicating where users are to enter commands. T U TFT display—See active-matrix display.
Index A AC adaptor 33 AC power 96 AC power light 33 accessing network 115 adding memory check total memory 47 memory (optional) 39 optional external devices 38 adequate ventilation cooling fan 32 adjusting TouchPad™ settings 66 Application Cards 163 audio features 115 B backing up files 84, 92 battery battery life 95 Call2Recycle™ 110 care 107, 108 changing 104 charge indicator light 35 charge time 96 charger 96 charging 35, 96 charging the real-time clock (RTC) 97 conserving power 101 determine remaining
Index running computer on battery power 94 safety precautions 107 setting notifications 101 battery indicator light 99 BIOS Setup see TOSHIBA Hardware Setup button power 37 Shut down 40, 73 start 113 C Call2Recycle™ battery 110 caring for your computer 81 changing battery 104 character keys 85 charging the battery 35 cleaning the computer 81 communications set up 114 computer caring for 81 cleaning 81 environmental precautions 110 moving 82 restarting 76 running on battery power 94 setting up 32 turn
Index E 193 emulate a full-size keyboard 85 enabling TouchPad™ 67, 173 ENERGY STAR® 24 exploring desktop 111 external devices keyboard 69 mouse 69 external display, adjusting 69 Lock (Instant security) 166 Output (Display switch) 170 power plan 167 Sleep mode 168 using to set a power plan 103 volume mute 165 Zoom (Display resolution) 174 zooming in 175 zooming out 175 Hot Key Cards 161 Hot key functions 165 F I file extensions using 91 files backing up 84, 92 file names 91 printing 91 restore 93 savi
Index using 84 keyboard, external 69 keys Ctrl Fn Alt 85 function keys 85 overlay for cursor control 87 overlay keys 86 overlay to type numeric data 87 L troubleshooting 147 monitoring battery power 98 mouse installing 69 mouse utility 131 moving the computer 82 N network accessing 115 connecting your computer 115 networking wireless 114 notification area 114 LEDs system indicator lights 99 AC adaptor light 98 AC power light 33, 34 battery light 35 cursor control overlay light 87 numeric overlay l
Index power button 37 power management 96 optimum performance 96 power plans selecting power plan options 102 using a hot key 103 power saving options 101 powering down using Hibernate 76 using Sleep 79 precautions safety 30 printer connecting 69 setting up 70 troubleshooting 150 USB-compatible 69 printing a file 91 problem solving Startup options 141 program, starting 87 program, starting from Start menu 88 projector connecting 67 R real-time clock (RTC) battery 95 recording sounds 115 recovery checking
Index Shut down button 40, 73 command 73 computer 40, 73 Hibernation mode 76 Sleep mode 79 Sleep mode 72 configuring 78 configuring options 79 hot key 168 powering down 79 Shut down 79 starting again from 81 using 78 software Setup Wizard 38 software program starting 87 starting from Start menu 88 sounds recording 115 speakers using external 116 start button 113 starting a program 87 Search programs and files field 89 Windows® Explorer 88 Windows® Start menu 88 starting a program from Start 88 startin
Index error message, warning resume failure 139 Error-checking 148 external display problems 148 external keyboard 146 external monitor 147 good computing habits 152 hard disk drive is slow 149 Help and Support, Windows® operating system 142 high-pitched noise 149 installing hardware/software 156 keyboard 146 keyboard will not respond 138 memory problems 144 missing files/trouble accessing a drive 148 power and batteries 144 printer 150 program stops responding 137 restore points 154 screen does not look c
