TOSHIBA POS Terminal ST-A10 SERIES Owner's Manual
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Warnung Dies ist ein Klasse A Produkt. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen. ATTENTION Ce produit est de classe A.
Safety Summary SPTM-0009 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment.
Safety Summary Disconnect the plug. Connect a grounding wire. SPTM-0009 If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorized TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or electric shock. Disconnect the plug. Ensure that the equipment is properly grounded. Extension cables should also be grounded.
SPTM-0009 TABLE OF CONTENTS Page 1. 2. 3. 4. INTRODUCTION ----------------------------------------------------------- 1-1 1.1 Accessories -------------------------------------------------------------------------------- 1-1 APPEARANCE ------------------------------------------------------------- 2-1 2.1 2.2 2.3 2.
SPTM-0009 1. INTRODUCTION 1.1 Accessories 1. INTRODUCTION Thank you for choosing the TOSHIBA POS Terminal. This POS terminal contains all the high performance register functions necessary for a specialty/hospitality POS terminal and enables the user oriented system configuration. The operation panel can be chosen from 12-inch TFT display and 15-inch TFT display.
2. APPEARANCE SPTM-0009 2. 1 Standard Model 2. APPEARANCE 2.
2. APPEARANCE SPTM-0009 2. 1 Standard Model LED and CONTROL BUTTON Power LED (Blue) DESCRIPTION This is the LED to indicate the power ON/OFF status of the POS terminal. The blue LED is illuminated when the power is ON. HDD LED (Yellow) The yellow LED is illuminated during the access to the hard disk drive. Power Switch This is the switch to turn the power of the POS terminal ON or OFF. Brightness Control This is used to adjust the brightness of the operator’s display.
2. APPEARANCE SPTM-0009 2.2 Available Options 2.
2. APPEARANCE SPTM-0009 2.3 Examples of POS Terminal with Some Options 2.
2. APPEARANCE SPTM-0009 2.4 Connectors 2.4 Connectors CAUTION! The drawer interface connector is exclusively for connecting the drawer. Do not connect a phone line or any other cables than the drawer cable to this connector. Doing so may cause a failure of the phone line and this terminal.
2. APPEARANCE SPTM-0009 2.4 Connectors Connector Description AC inlet A connector for the AC inlet PS/2 (Mouse, Keyboard) Mini-DIN 6pin female type connector Connector for the PS/2 type mouse, Connector for the PS/2 type keyboard USB: General 5V USB X 6 USB: 24V Powered X1 Connector for the USB (Universal Serial Bus) interface USB V2.0/1.1 and UHCI (Conforming to Universal Hub Controller Interface V2.0/1.1) NOTE: USB functions may not be supported depending on the Operating System.
3. INSTALLATION PROCEDURE SPTM-0009 3.1 Environment for Installation 3. INSTALLATION PROCEDURE WARNING! Care must be taken not to get your fingers caught between the LCD Frame and the POS terminal when bending the display downward. CAUTION! When removing the protective film from the display surface, please be sure to do it slowly. If it is done quickly, static electricity may generate, and the TFT may be damaged. 3.
3. INSTALLATION PROCEDURE SPTM-0009 3.2 Connecting the AC Plug 3.2 Connecting the AC Plug 1. Push on both sides of the molded Tower (TWR) Tail Cover to remove it from the system in order to gain access of the AC inlet. 2. Fully insert the Power Cord Plug into the Inlet of the POS terminal. Power Cord Plug TWR Tail Cover Inlet Push Power Cord Plug Push Lift NOTE: The Power cord is not included in the carton. Please prepare it separately from local dealer.
4. ADJUSTMENT SPTM-0009 4.1 Tilt Angle Adjustment 4. ADJUSTMENT Tilt angle and brightness of the operator’s display can be adjusted. Adjustment method is common to both of 12-inch display model and 15-inch display model. CAUTION! 1. Do not adjust the display angle by holding the LCD panel. Doing so may damage the unit. Be sure to hold the LCD frame. 2. Care must be taken not to catch your fingers between POS terminal and the LCD Frame when bending the display backward. 4.
4. ADJUSTMENT SPTM-0009 4.2 Brightness Adjustment 4.2 Brightness Adjustment The brightness control is provided on the lower right of the operator’s display. Turning it to the left makes the display darker, and turning it to the right makes the display brighter.
5. MAGNETIC CARD READER (OPTION) SPTM-0009 5.1 How to Read Magnetic Card 5. MAGNETIC CARD READER (OPTION) The optional magnetic card reader can be installed. 5.1 How to Read Magnetic Card Insert the magnetic card into the upper portion of the magnetic card reader slot and slowly move the card downward. NOTE: Moving the magnetic card too fast or too slowly may cause a read error.
6. iButton® (OPTION) SPTM-0009 6.1 How to Read iButton 6. iButton® (OPTION) The optional iButton unit can be installed on the bottom of the LCD. 6.1 How to Read iButton CAUTION! 1. Keep storage media, like a floppy disk, away from the touch probe. The magnet of the touch probe may destroy the stored data. 2. Keep a metal object like a paper clip away from the touch probe.
7. GENERAL MAINTENANCE SPTM-0009 7. GENERAL MAINTENANCE 7. GENERAL MAINTENANCE WARNING! 1. Be sure to disconnect the power cord prior to performing any maintenance. 2. Do not pour water directly on or wipe the operator’s display with a soaked cloth, as this may cause fire, electric shock, or machine failure. CAUTION! 1. Never use an organic solvent like thinners or benzene for cleaning. Using such solvents may discolor the covers. 2. Do not use any sharp object to clean the operator’s display.
8. TROUBLESHOOTING SPTM-0009 8. TROUBLESHOOTING 8. TROUBLESHOOTING WARNING! If you cannot solve a problem with the following solutions, do not attempt to repair it by yourself. Turn the power off, unplug the POS Terminal, then contact the nearest TOSHIBA TEC service representative for assistance Symptom The power does not turn on. Check Point • Is the power cord plugged in correctly? • Is the power supplied to the AC outlet? • Has the circuit breaker blown? Solution • Plug in correctly.
9. SPECIFICATIONS SPTM-0009 9.1 Basic Specifications 9. SPECIFICATIONS 9.1 Basic Specifications Description Item Audio Operating Temperature Operating Humidity 12-inch LCD Dimensions 15-inch LCD 12-inch LCD Weight 15-inch LCD VIA C7 1.5GHz 512 MB, 2 slots (2 GB max) 3.5" HDD SATA (40 GB) ISO-3-track one sided type (option) Option 4 (2x normal.
9. SPECIFICATIONS SPTM-0009 9.2 Options 9.2 Options Option Model Description DRWST-51A-4MVK-QM-R DRWST-51A-8MVK-QM-R Drawer Unit Drawer Type Tilt Type Customer Display Fixed Type Customer Display Remote Type Customer Display 24V-drive standard drawer Dimensions and Weight: 460(W) x 400(D) x 115(H) mm / 18.1(W) x 15.7 (D) x 4.
English Waste Recycling information for users: Following information is only for EU-member states: The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste. By ensuring that this product is disposed of correctly you will be helping to prevent potentially negative consequences for the environment and human health, which could otherwise be caused by incorrect waste handling of this product.
E PRINTED IN SINGAPOLE SPTM-0009
