OWNER’S MANUAL LCD Monitor P47LSA 1
Contents Safety Instructions-------------------------------------------------------- 3 Notes and Cautions for Use-------------------------------------------- 9 On usage------------------------------------------------------------------------- 9 On disposal or handing over to a new owner -------------------------- 9 Exemptions---------------------------------------------------------------------- 9 Features----------------------------------------------------------------------- 9 Specifications----------------
Safety Instructions Before using this unit, please read this manual thoroughly to avoid injury and/or damage. Be sure to observe the following instructions, carefully reading each sign and figure listed below: Meaning of Signs Sign Meaning of Sign May cause death or serious injury*1. May cause injury*2 or material damage*3.
If water is spilled or objects are dropped inside the unit, remove the power plug from the outlet immediately. If the unit is still used in this condition, it may cause a fire or an electrical shock. Contact your dealer for inspection. If the unit is dropped or the cabinet is damaged, remove the power plug from the outlet immediately. If the unit is still used in this condition, it may cause a fire or an electrical shock. Contact your dealer for inspection.
Do not place the unit in an unstable location, such as a shaky table or incline. The unit may fall down and cause injury or damage. Install the unit on a horizontal, stable surface. Do not place the unit in a location subject to vibration. The unit may fall down because of the vibration and may cause an injury. Insert the power plug fully into a 100 － 240V AC outlet. • If an outlet other than 100－240 V AC is used, it may cause fire or electrical Shock. • Improper insertion of the plug may cause fire.
Do not insert objects inside the unit. If metallic materials or combustibles such as paper get inside the unit from ventilation holes and other places, it may cause a fire or an electrical shock. Be especially careful that children do not insert objects in the unit. If there is thunder or lightening, do not touch the unit or the power plug. This may cause an electrical shock. Cleaning If dust has collected on the power plug connectors, remove the plug from the outlet and clean off the dust.
Do not block the ventilation holes on the unit. The inside of the unit will overheat if the ventilation holes are sealed, which may result a fire. • When installing the unit near a wall, keep the unit at least 10 cm from the wall. • Do not place the unit in a closet or bookshelf where ventilation is poor. • Do not spread a newspaper, tablecloth or curtain over the unit. • Do not place the unit on an unstable surface, such as a rug, or a cushion, etc.
Precautions for the remote control battery: Only use the specified battery type. Be sure to insert battery by matching the + and –. Do not recharge, heat, disassemble, short or throw battery into a fire. Do not use the battery beyond their usage period (designated on the battery), do not leave worn out battery in the unit. If these precautions are not observed, it may lead to battery leakage or explosion and may cause burn and injury.
Notes and Cautions for Use On usage • Some parts of the display are hot during operation. Please be careful. • In case of moving long-distance, wrap the unit with blanket to avoid damages. Be careful not to bump the unit. • Do not spray on the unit with volatile liquid like insecticide. Do not make contact with rubber or vinyl for a long time. It will damage the coating. On disposal or handing over to a new owner • It is recommended to initialize the unit by resetting “PICTURE” and “SETUP” menu.
Specifications Model name P47LSA Type 47-inch flat panel LCD display unit Acceptable signals NTSC/PAL/PC Image device 16:9 LCD panel Light source fluorescent back light lamps Resolution 1920 x 1080 dot x RGB Brightness 550cd/m2 (Typ.) Contrast 1000:1 Response time 12 mS (Typ.) Color temperature 3200K, 5400K, 6500K, 9300K, USER Viewing Angle Horizontal / Vertical: 176 degrees, 85 deg.
Names and Functions of Controls Front LCD Screen -Power ON-Stand by Indicator -Remote Control Receiver -Light sensor Side Controls No. Key Descriptions 1 Power Power on / Power off 2 Select Activate selection 3 ＋ Menu Right 4 － Menu Left 5 < Menu Down 6 > Menu Up 7 Exit OSD control Menu button Side Keypad lock/unlock control: Use control push buttons at side: Lock: Press (+) and (<) at the same time and OSD will be locked.
Names and Functions of Controls OSD control Menu button Power on / Power off Menu Left Menu Right Menu Up Menu Down Activate selection One level up Auto adjustment Input source selection Picture in picture PIP picture switch Battery Installation (2) (1) (3) To replace battery inside Push down a little as (1) in the picture and pull the back cover Replace with the new battery as (2), 1 piece Lithium battery (CR2032) make sure the polarity of battery is correct.
Supplied Accessories Please check all are supplied. Owner’s Manual x 1 Remote Control x 1 VGA Cable x 1(1.8M) OWNER’S MANUAL LCD Monitor P47LSA RCA Cable x 1(1.8M) S-Video Cable x 1 (1.8M) Power Cord x 1 (1.8M) DVI-D Cablex1 (1.8M) Component Cable x 1 (1.
Connection VIDEO SYSTEM INPUT You can select VIDEO input from 3 terminals below; Terminal Type Suitable signals VIDEO-IN RCA NTSC/PAL S-VIDEO S-Video Mini Din 4pin NTSC/PAL YUV (Y Pb/Cb Pr/Cr) Component Mini Din 8 pin NTSC/PAL • Suitable signal is automatically selected.
Installation To a service technician For safety, make sure the place has enough strength to hold the whole weight of the monitor and the frames (*1). If necessary, reinforce the place before installation. At least two people are needed for installation. Be careful not to lose removed screws or parts. Before starting installation, discuss well with customers about the position to install, and get their agreement. After installation, check the installation is correct and safe.
Dimension 16
Power On/Off Before turn on, wire all the cable connecting to auxiliary equipment, power cord, etc. There are two controls for power, Main power switch and POWER (standby / on) button. Main power switch Bottom Front Mode LED indicator Power on Green Power Standby Yellow No signal Orange No power input No LED If Main power switch is not On, you cannot turn on the unit by the POWER (Standby / On) button.
Menu Function Display Menu, pictures or various functions can be set with the buttons on the remote control. The following are summary of Menu Function. For details, please see to refer pages. Function of Remote control No. Key Descriptions 1 Power Power on / Power off 2 3 4 5 6 Adjust clock, phase, H position and V position Automatically Input source Source selection PIP Picture in picture Switch PIP picture switch Enter Activate selection Auto No.
Menu display chart MAIN MENU DISPLAY MENU SELECTION POSITION PIP CONTROL IMAGE COLOR Display PIP input selection OSD Position Vertical ．．．．．．．（－ , ＋） Horizontal ．．．．．．．（－ , ＋） Blend ．．．．．．．（－ , ＋） Time Out ．．．．．．．（－ , ＋） OSD Zoom ．．．．．．．（On , Off） English ．．．．．．．（Select） Factory Reset．．．．．．（Yes , No） Light sensor ．．．．．．（On , Off） Light sensor value ．．．．（－ , ＋） Langue Others OSD Brightness ．．．．．．．（－ , ＋） Contrast ．．．．．．．（－ , ＋） Hue ．．．．．．．（－ , ＋） Saturation ．．．．．．．（－ , ＋） Flash-Tone ．．．．．．．（Off,
Main Menu page Display Menu page From normal mode, [MENU] button will guide to this page. After entering Main Menu, [ENTER] will display this page. To escape from the mode, use [Exit]. In this Display Menu page, DISPLAY, IMAGE, POSITION, COLOR or PIP CONTROL can be selected. Most of them are picture quality or adjustment related. Once entered to the any mode, such as above right, DISPLAY Menu mode, note that the highlighted section is selected.
Position Menu page Image Menu page From Image mode, [Right] button will guide to this Position page. From Image mode, [ENTER] will display this page. Color Menu page From Position mode, [Right] button will guide to this Color mode. Here, selection of Color Temperature is available. [Down] key will enter to this Color Temperature selection mode. The [Left]/[Right] key will make the selection and [Enter] key decides. The arrow marks indicate “Selected and Highlighted”, not appeared in an actual picture.
PIP Control page In this page, Picture-in picture feature is selected. PIP can insert such as PC image on the base and Video image in the small window, this is one of the example. The position and also the size of the inserted image are possible to modify by selecting the “adjust mode” by [Up] or [Down] key, then using [Left] or [Right] key to select. Also, refer to the picture below left, this is indicating PIP icon and selecting this icon and using [Enter] button, This picture appears.
OSD ( On Screen Display ) Control page Language selection page Factory Reset page Only ‘English’ selection is available. When all reset is necessary, this is the page to reset. The Light Sensor is placed at the power indicator area, also, wireless remote control receiver is located at the same place. The purpose of this light sensor is to check the environment light level. If the area was dark, then, display Brightness may not be so much brighter compared to the bright noon time.
Input signal selection and its contents This page can be displayed by using [Down] key while at the Main Menu page, appeared in page 21. This page is convenient to check the incoming resolution as indicated here as 1024x768@60Hz. “IGP” is indicating that the input signal is coming from Graphic card signal, as Input Graphic Processor. A Guide to Simple Problem Solving Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing.
Input Signal < Horizontal > Video Sync B D C H-parameters A: Total period B: Sync. width C: Back porch D: Active video E: Front porch E A Dot clock (MHz) Sync polarity H V 26.250 50.000 21.000 N 31.469 59.940 25.175 N VGA 640x480 37.861 72.809 31.500 37.500 75.000 SVGA 800x600 31.400 50.000 6 35.156 56.250 7 37.879 60.317 48.077 72.
USER-INSTALLER CAUTION YOUR AUTHORITY TO OPERATE THIS FCC CERTIFIED EQUIPMENT COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THIS PART RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
