Toshiba Personal Computer Satellite A210 Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL]
Copyright © 2007 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Personal Computer Satellite A210 Maintenance Manual First edition May 2007 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite A210, referred to as the M100 Series in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention.
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the M100 Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third.
Table of Contents Chapter 1 Hardware Overview 1.1 Features ............................................................................................................................1-1 1.2 System Unit ......................................................................................................................1-5 1.3 2.5-inch Hard Disk Drive .................................................................................................1-6 1.4 Optical Disc Device ........................
2.20 HDMI Troubleshooting…………………………………………………………………..48 2.21 MIC Troubleshooting ……………………………………………………………………54 2.22 Finger Troubleshooting …………………………………………………………………56 Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test .......................................................Error! Bookmark not defined. 3.2 Executing the Diagnostic Test .......................................Error! Bookmark not defined. 3.3 Display Configuration ...................................................
Chapter 4 Replacement Procedures 4.1 General .......................................................................... Error! Bookmark not defined. 4.2 Battery ........................................................................... Error! Bookmark not defined. 4.3 PC Card ......................................................................... Error! Bookmark not defined. 4.4 Memory Card ................................................................ Error! Bookmark not defined. 4.5 HDD ..
Appendices Appendix A Handling the LCD Module ................................................................................. A-1 Appendix B Board Layout ...................................................................................................... B-1 Appendix C Pin Assignments.................................................................................................. C-1 Appendix D Keyboard Scan/Character Codes ........................................................................
Chapter 1 Hardware Overview 1 [CONFIDENTIAL]
1 Hardware Overview Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series Maintenance Manual 1-ii
1 Hardware Overview Chapter 1 Contents 1.1 Features ...................................................................................................................... 1-1 1.2 System Unit................................................................................................................ 1-5 1.3 2.5-inch Hard Disk Drive........................................................................................... 1-6 1.4 Optical Disc Device ...............................................
1 Hardware Overview Figures Figure 1-1 2.5-inch HDD ................................................................................................ 1-6 Tables Table 1-1 Table 1-1 Table 1-2 Table 1-3 Table 1-3 2.5-inch HDD specifications ......................................................................... 1-6 2.5-inch HDD specifications (Continued)..................................................... 1-7 DVD Super Multi Double Layer drive specifications...................................
1.1 Features 1.1 1 Hardware Overview Features The Minnesota 10A/10AG (Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series)Series Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight and high reliability.
1 Hardware Overview 1.1 Features Offers constant voltage 19V output source with 120W max output power capacity for Minnesota 10AG • 3 cells of Li-Ion 18650 size, smart battery pack with 2000mAH x 10.8V (21.6W) • 6 cells of Li-Ion 18650 size, smart battery pack with 4000mAH x 10.8V (43.2W) • 9 cells of Li-Ion 18650 size, smart battery pack with 6000mAH x 10.8V (64.8W) • Approximately 12 hours or longer charging time to 100% battery capacity with system switched on.
1.1 Features 1 Hardware Overview • One S-Video port • One microphone port • One headphone-out jack • Digital/Rotary volume control • Wireless communication switch • One DC-in jack • One RJ-11 jack for 56kbps V.
1 Hardware Overview 1.1 Features Switches • Power button • Two programmable launch buttons • Four control buttons for CD playing • Wireless communication switch Security • Fingerprint authentication AC Adapter • Universal AC adapter module • Liteon & Delta 75W, 90W,120W adapters • Output voltage: 19Vdc • Input Voltage/Frequency range: 90-264Vac, 47-63Hz Display • 15.
1.2 System Unit 1.2 1 Hardware Overview System Unit The system unit is composed of the following major components: Processor • AMD Turion 64 Dual Core TL-50/ TL-52/ TL-53/ TL-56/ TL-58/ TL-60/ TL64/ TL-66 • AMD Sempron Single Core 3400+/ 3500+/ 3600+/ 3800+ System Logic • AMD RS690MC for UMA platform. • AMD RX690 for discrete platform. • ATI South Bridge SB600. Memory • Two DDR-II 667MHz SO-DIMM • Supports Dual channel • Up to 4GB.
1 Hardware Overview 1.3 1.3 2.5-inch Hard Disk Drive 2.5-inch Hard Disk Drive The internal HDD is a random access non-volatile storage device. It has a non-removable 2.5-inch magnetic disk and mini-Winchester type magnetic heads. The computer supports up to 250G HDD. The HDD is shown in Figure 1-1. Specifications are listed in Table 1-1.
1.3 2.5-inch Hard Disk Drive Items Formatted capacity (GB) Logical Blocks (LBA) Rotational speed (rpm) Toshiba HDD Buffer (MB) Hitachi HDD Buffer (MB) Fujitsu HDD Buffer (MB) Bytes per sector 1 Hardware Overview 160GB 200GB 250GB 300GB 149.05 186.31 232.89 279.46 312,581,808 390,720,968 488,397,168 586,072,368 5400/4200 4200 4200 4200 8 8 N/A N/A 8 N/A N/A N/A 8 8 8 8 512 512 512 512 Table 1-1 2.
1 Hardware Overview 1.4 1.4 Optical Disc Device Optical Disc Device 1.4.1 DVD Super Multi Double Layer The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs.
1.4 Optical Disc Device 1 Hardware Overview 1.4.2 HD DVD-ROM The HD DVD drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, HD DVD-ROM reads HD DVD-ROMs at maximum 1x speed DVD-ROMs at maximum 8x speed and CD-ROMs at maximum 24x speed. It writes CD-R at up to 16x speed, CD-RW at up to 10x speed, DVD-R at maximum4x speed, DVD-RW at maximum 6x speed, DVD+RW at maximum 4x speed, DVD+R at maximum 4x speed, DVD+R (double layer) at maximum 2.
1 Hardware Overview 1.5 1.5 Power Supply Power Supply This specification defines the performance and characteristics of the 75W, 90W, and 120W AC adapter power supply. It supplies a constant voltage 19V output source for the Minnesota 10A/10AG (Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series)Series Personal Computer.
1.5 Power Supply 1 Hardware Overview Battery charging control • The EC controls the following. – The quick charging ON/OFF – The detection of full charge Detection of the low battery • The EC detects the low battery point by the gas gauge. – LB10M: The system will be driven by the battery for 12 more minutes. – LB0: The battery won’t be able to drive the system after 3 minutes. – LB1: The battery can drive the system only during the suspend process. – LB2: The battery cannot drive the system.
1 Hardware Overview 1.6 1.6 Batteries Batteries The computer has two types of battery: Main battery pack (18650 size) RTC battery The removable main battery pack is the computer’s main power source when the AC adapter is not attached. The battery specifications are listed in the table below. Battery name Material Output voltage Capacity Main battery (3cells) Lithium-lon 10.8V 2000mAH Main battery (6 cells) Lithium-Ion 10.8V 4000mAH Main battery (9 cells) Lithium-Ion 10.
1.6 Batteries 1 Hardware Overview 1.6.1 Main Battery Battery charging is controlled by a power supply microprocessor that is mounted on the system board. The power supply microprocessor controls whether the charge is on or off and detects a full charge when the AC adapter and battery are attached to the computer. The system charges the battery using quick charge or trickle charge.
1 Hardware Overview 1.6 Batteries 1.6.2 RTC battery The RTC battery provides power to keep the current date, time and other setup information in memory while the computer is turned off. The table below lists the charging time and data preservation period of the RTC battery. The RTC battery is charged by the adapter or main battery, while the computer is powered on.
Chapter 2 Troubleshooting Procedures 2
2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting Introduction ........................................................................................3 2.2 Troubleshooting Flowchart............................................................................................4 2.3 Power Supply Troubleshooting......................................................................................9 2.4 Display Troubleshooting.............................................................
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2) ....................................................................... 5 Figure 2-1 Troubleshooting flowchart (2/2) ....................................................................... 6 Figure 2-2 Power Supply Troubleshooting Process............................................................ 9 Figure 2-3 Display troubleshooting process .....................................................................
2 Troubleshooting Procedures 2.1 Troubleshooting Introduction Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Display 7. Speaker 13. Camera 2. USB Floppy Drive 8. Optical drive 14. Bluetooth 3. Keyboard 9. Modem 15 HDMI 4. USB ports 10. Express card unit 16. MIC 5. TV-out port 11. IEEE 1394 port 17. Finger 6. TouchPad 12.
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart If you know the location of the malfunction, turn directly to the appropriate section of this chapter. If the problem is unspecified, use the flowchart in Figure 2-1 as a guide for determining which troubleshooting procedures to execute. Before performing any troubleshooting procedures, verify the following: z Ask the user if a password is registered and, if it is, ask him or her to enter the password.
2 Troubleshooting Procedures START C o n n e c t th e A C a d a p te r to th e D C -IN so c k e t No Is th e D C -IN L E D o n ? P e rfo rm th e P o w e r S u p p ly T ro u b le sh o o tin g p ro c e d u re s in se c tio n 2 .3 Y es Is th e B a tte ry L E D o n ? No P e rfo rm th e P o w e r S u p p ly T ro u b le sh o o tin g p ro c e d u re s in se c tio n 2 .3 No P e rfo rm th e P o w e r S u p p ly T ro u b le sh o o tin g p ro c e d u re s in se c tio n 2 .
2 Troubleshooting Procedures A Does typed characters appear correctly? No Perform the Keyboard Troubleshooting procedures in section 2.6 No Perform the FDD Troubleshooting procedures in section 2.5 Yes After confirming which diagnostics test has detected an error, perform the appropriate procedure as outlined below. Yes Insert the diagnostics disk into the FDD. Then run the diagnostics test program.
2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The test program should be executed several times to isolate the problem. When a problem has been located, perform the appropriate troubleshooting procedures as follows: 1. If an error is detected by the battery test, perform the Power Supply Troubleshooting procedures in Section 2.3. 2. If an error is detected by the display test, perform the Display Troubleshooting procedures in Section 2.4.
2 Troubleshooting Procedures Other problems that are not covered by the diagnostics program may be discovered by a user. 1. If an error is detected when using an external USB device, perform the External USB Devices Troubleshooting procedures in Section 2.6. 2. If an error is detected when using the TV-out connection, perform the TV-Out Failure Troubleshooting procedures in Section 2.7. 3. If an error is detected when using the speakers, perform the Speaker Troubleshooting procedures in Section 2.10. 4.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The flowchart in Figure 2-2 gives a summary of the process.
2 Troubleshooting Procedures Amber color off Battery not in low or critical low state; It’s in discharging state Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series Maintenance Manual 11
2 Troubleshooting Procedures Table 2-2 DC-IN LED AC-IN LED Power supply status Solid on AC power exists (LED is solid Blue). Off No AC power exists. To check the power supply status, install a battery pack and connect an AC adaptor to the DC-IN port on the computer and to a power supply. If the DC-IN LED or Battery LED is not lit, go to Procedure 2. Procedure 2 Adaptor / battery replacement A faulty adaptor may not supply power or may not charge the battery. Perform Check 1.
2 Troubleshooting Procedures Procedure 3 Power supply connection check The power supply wiring diagram is shown below: AC adaptor cord AC power cord AC adaptor System board Battery Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord. If there is no damage, go to Check 2.
2 Troubleshooting Procedures Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5. 3. Run the Diagnostic test following the procedures described in Chapter 3, Tests and Diagnostics. If no problem is detected, the battery is functioning normally.
2 Troubleshooting Procedures 2.4 Display Troubleshooting STA RT P e r f o rm e x te r n a l d is p la y c h e c k ( P r o c e d u re 1 ) D o e s th e e x te r n a l d is p la y f u n c tio n o k ? No P e r f o r m d ia g n o s tic c h e c k ( P ro c e d u r e 2 ) Y es W a s a d is p la y p r o b le m d e te c te d ? No D is p la y is n o t f a u lty . C o n tin u e tr o u b le s h o o tin g r e f e r to F ig u r e 2 .
2 Troubleshooting Procedures This section describes how to determine if the computer’s display is functioning properly. The process is outlined in Figure 2-3. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External display check Procedure 2: Diagnostic check Procedure 3: Connector and replacement check Procedure 1 External display check Connect an external display to the computer’s external monitor port, and then boot the computer.
2 Troubleshooting Procedures Procedure 3 Connector and replacement check The FL inverter board, LCD module, and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Make sure the DDR RAM module is seated properly. Test display again. If the problem still exits, replace the DDR RAM module.
2 Troubleshooting Procedures 2.5 Keyboard Troubleshooting STA RT P e r f o r m e x te r n a l k e y b o a rd c h e c k (P r o c e d u r e 1 ) D o e s th e e x te r n a l k e y b o a rd f u n c tio n o k ? Y es P e r f o r m d ia g n o s tic c h e c k ( P ro c e d u r e 2 ) No W a s a k e y b o a rd p r o b le m d e te c te d ? K e y b o a r d is n o t fa u lty . C o n tin u e tr o u b le s h o o tin g - r e f e r to F ig u r e 2 .
2 Troubleshooting Procedures Figure 2-4 Keyboard troubleshooting process To determine if the computer’s keyboard is functioning properly, perform the following procedures. Figure 2-5 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures Check 3 2.6 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.
2 Troubleshooting Procedures Figure 2-5 External USB device troubleshooting process To determine if the computer’s external USB devices are functioning properly, perform the following procedures. Figure 2-6 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: External device and connection check Procedure 2: Replace system board Procedure 1 External device and connection check The USB device may be damaged or the connection may be faulty. Perform Check 1.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures To determine if the computer’s TV-out port is functioning properly, perform the following procedures. Figure 2-7 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: TV connection check Procedure 2: TV set check Procedure 1 TV connection check The TV cable may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure TV cable is firmly plugged into both the TV set and the TV-out port of the computer.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures To determine if the computer’s built-in TouchPad is functioning properly, perform the following procedures. Figure 2-9 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: TouchPad connection check Procedure 2: TouchPad replacement check Procedure 1 TouchPad connection check The TouchPad is connected via the TouchPad FPC to the system board. Make sure the TouchPad FPC cable is firmly connected to the TouchPad and system board.
2 Troubleshooting Procedures 2.9 Speaker Troubleshooting START Perform audio source test (Procedure 1) Do all sources have same problem? No Speakers are not faulty.
2 Troubleshooting Procedures To determine if the computer’s built-in speakers are functioning properly, perform the following procedures. Figure 2-10 outlines the process. First adjust the speaker volume to an appropriate level. Start with Procedure 1 and continue as instructed. Procedure 1: Audio source test Procedure 2: Earphone test Procedure 3: Connection check Procedure 4: Replacement check Procedure 1 Audio source test Try different audio sources (e.g.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures This section describes how to determine if the computer’s internal optical drive is functioning properly. The Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series Maintenance Manual Series can accommodate the following optical drives: DVD SuperMulti supporting +-R Double Rayer Figure 2-11 outlines the process. Perform the steps below starting with Procedure 1 and continue with the other procedures as required.
2 Troubleshooting Procedures Procedure 5 Connection check and replacement check The optical drive connects to the system board. The drive may be disconnected, or the drive or system board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the drive is firmly connected to the system board. If the connection is good and there is still an error, go to Check 2.
312 Troubleshooting Procedures 2.
322 Troubleshooting Procedures This section describes how to determine if the computer's modem is functioning properly. Figure 2-12 outlines the process. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Telephone line connection check Procedure 2: Modem card connection check Procedure 3: Modem card replacement check Procedure 1 Telephone line connection check The telephone cable may be damaged or the connections may be loose.
332 Troubleshooting Procedures 2.12 Express card Troubleshooting START P e rfo rm E x p re ss c a rd te st (P ro c e d u re 1 ) D o e rro rs o c c u r d u rin g E x p re ss c a rd te st? No E x p re ss c a rd u n it is n o t fa u lty .
342 Troubleshooting Procedures This section describes how to determine if the Express card player is functioning properly. The process is summarized in Figure 2-13. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Express card test Procedure 2: Express card socket replacement check Procedure 1 Express card test The Express test card contains a Express test program.
352 Troubleshooting Procedures 2.13 IEEE 1394 Troubleshooting START Perform IEEE 1394 device check (Procedure 1) Is IEEE 1394 transmission ok? Yes Perform diagnostic check (Procedure 2) No Was an IEEE 1394 problem detected? No IEEE 1394 port and transmission are not faulty. Continue troubleshooting - refer to Figure 2.
362 Troubleshooting Procedures To determine if the computer’s IEEE 1394 system is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: IEEE 1394 device check Procedure 2: Diagnostic check Procedure 3: Connection and replacement check Procedure 1 IEEE 1394 device check Connect an IEEE 1394 device to the computer’s IEEE 1394 port, then boot the computer for Windows Vista.
372 Troubleshooting Procedures 2.14 Wireless LAN Troubleshooting START Perform diagnostic test (Procedure 1) Was a wireless LAN problem delected? No Wireless LAN system is not faulty. Continue troubleshooting - refer to Figure 2.
382 Troubleshooting Procedures The wireless LAN antenna wire, wireless LAN unit or system board may each be the source of a wireless LAN fault. Any of these components may be damaged. To determine if the computer’s wireless LAN system is functioning properly, perform the following procedures. Figure 2-15 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
392 Troubleshooting Procedures Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.
402 Troubleshooting Procedures 2.
412 Troubleshooting Procedures The Camera board or system board may be the reason of a Camera fault. Either of these two components may be damaged. To determine if the computer’s Camera is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
422 Troubleshooting Procedures 2.16 Bluetooth Troubleshooting START Preform diagnostic test (Procedure 1) Was a Bluetooth problem detect? Bluetooth is not faulty. Continue troubleshooting-refer to Figure 2.1 Perform connector and replacement check (Procedure 2) Replace Bluetooth antenna moudle.
432 Troubleshooting Procedures The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be damaged. To determine if the computer’s Bluetooth is functioning properly, perform the following procedures. Figure 2-16 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
442 Troubleshooting Procedures 2.17 4 in 1 card Troubleshooting START Perform 4 in 1 CARD test (Procedure 1) Do errors occur during 4 IN 1 CARD test? No 4 IN 1 unit is not faulty.
452 Troubleshooting Procedures This section describes how to determine if the 4 IN 1 Card player is functioning properly. The process is summarized in Figure 2-16. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: 5 in 1 card test Procedure 2: Express socket replacement check Procedure 1 4 in 1 card test The 4 in 1 Card test card contains a 4 in 1 card test program.
462 Troubleshooting Procedures 2.
472 Troubleshooting Procedures The HDD or system board may be the reason of a HDD fault. Either of these two components may be damaged. To determine if the computer’s HDD is functioning properly, perform the following procedures. Figure 2-15 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
482 Troubleshooting Procedures 2.
492 Troubleshooting Procedures To determine if the computer’s CRT port is functioning properly, perform the following procedures. Figure 2-7 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: CRT connection check Procedure 2: CRT set check Procedure 1 CRT connection check The CRT cable may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure CRT cable is firmly plugged into both the CRT set and the CRT port of the computer.
502 Troubleshooting Procedures 2.
512 Troubleshooting Procedures To determine if the computer’s HDMI port is functioning properly, perform the following procedures. Figure 2-7 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: HDMI connection check Procedure 2: HDMI set check Procedure 1 HDMI connection check The CRT cable may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure HDMI cable is firmly plugged into both the CRT set and the CRT port of the computer.
522 Troubleshooting Procedures 2.21.
532 Troubleshooting Procedures Figure 2.21. MIC troubleshooting process The MIC line or system board may be the reason of a MIC fault. Either of these two components may be damaged. To determine if the computer’s MIC is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
542 Troubleshooting Procedures 2.
552 Troubleshooting Procedures Figure 2-22 Finger printer troubleshooting process The Finger printer board or system board may be the reason of a finger printer fault. Either of these two components may be damaged. To determine if the computer’s Finger printer is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
3.
Contents 3.1 The Diagnostic Test ............................................................................................................ 3 3.2 Executing the Diagnostic Test............................................................................................. 4 3.3 Display Configuration ........................................................................................................ 8 3.4 Speaker Audio Test ...........................................................................
3. Tests and Diagnostics 3.1 The Diagnostic Test This chapter explains how to use the Test & Diagnostic program to test the functions of the (Base on Minnesota 10A T&D version 1.0) hardware modules. The Test & Diagnostic Program is stored on the T&D diskettes. The program consists of a series of tests that run automatically when the Diagnostics Program items are selected and executed. NOTES: To start the diagnostics, follow these steps 1. Check all cables for loose connections. 2.
3. Tests and Diagnostics 3.2 Executing the Diagnostic Test DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the diagnostics diskette #1 in the floppy disk drive and turn on the computer. (The diagnostics diskette contains the DOS boot files.) And then follow the instructions to swap with the diagnostics diskette #2 for T&D program installed in RAM driver. NOTE: To execute the CD test, make sure the CD is installed in the ODD drive.
3.
3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Then press any key for next actions – the below display presented if copying test log file onto diskette is necessary. This action will be executed when “Y” key pressed. It will skip this process if “N” key pressed.
3. Tests and Diagnostics And then it will check if it’s necessary to leave this program. Program will quit when “Y” key pressed and it will go back main menu for next test if “N” key pressed.
3. Tests and Diagnostics 3.3 Display Configuration This Item will show the unit configuration. It includes: CPU type (Single/Dual Yunah; Cache ; CPU speed ;CPU FSB) DDRAM SIZE ODD TYPE ((DVD-SuperMulti; COMBO; …) Panel ID HDD type & capacity (Vendor ID. Model .
3 Tests and Diagnostics 3.4 Speaker Audio Test The speaker audio test allows the user to aurally confirm the speaker functions. And check both speakers if they are OK within 3 times “Beep” sound generated. NOTE: Remember to tune up the volume as “Maximum” before this test starts. The screen should display as below, indicating whether the test is passed or failed after the question.
3. Tests and Diagnostics 3.5 Fan ON/OFF Test The fan test allows the user to test aurally whether the fan is working. And follow the below procedures for this test: The computer will let the fan be “ON” after any key pressed. Feel the wind or listen the rotating sound to check whether the fan is working or not. NOTE: Remember to approach fan outlet that is near right side of unit whether fan is “ON”. The computer will stop the fan working after any key pressed.
3. Tests and Diagnostics 3.6 Main Battery Charge Test NOTE: The AC adaptor (90W, 19V) should be connected to successfully run this test. This test shows and measures the main battery: Battery type (Lion) Manufacturer (Sanyo/Panasonic/Sony) Remain charge capacity (0 ~ 100%) Charge function (PASS/FAIL) - “Battery Is Full” showed when “remain charge capacities” is 100% The screen should display as below, if the charge function is OK, will show:.
3 Tests and Diagnostics 3. 7 FDD Test NOTE: Before running the FDD test, prepare a formatted work diskette (1.44 MB). Remove the diagnostics diskette and insert the work diskette into the FDD. The contents of the floppy diskette maybe erased. The Floppy Disk Test includes three subtests of the: 1. Sequential seek/verify function (Range: Track 0 ~ 79) 2. Funnel code seek/verify function (Range: Track 0 ~ 79) 3.
3. Tests and Diagnostics 3. 8 ODD Test The ODD test allows a user to aurally confirm the ODD functions. NOTE: A CD disc (including data file) must be inserted into the ODD drive then must wait ODD drive initial OK (ODD LED stop flashing) before this test starts. The ODD test includes two subtests of the: 1. Random read/partial sequential read function 2. Eject ODD door The screen should display as below, indicating whether the subtests pass or fail when finished.
3 Tests and Diagnostics 3. 9 Keyboard Test The keyboard test checks the all keys function. NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test. When you execute this test, the keyboard layout is drawn on the display. When any key is pressed, the corresponding key on the screen changes to black as shown below. It will indicate whether the subtest is passed or failed after the question. NOTE: The “Fn” key cannot be tested in the keyboard test.
3. Tests and Diagnostics 3.10 Mouse (Pad) Test The Mouse test allows the user to select and assign values to the following, using the Touch Pad or “Tab” key to move between selections: 1. Mouse Speed (on a scale from slow to fast) 2. Acceleration (Off, Low, Medium, High) 3. Button Assignments (Left + Right / Right button, either Unassigned or Drag Lock) 4. Swap Buttons (Left /Right) NOTE: The Touch Pad test cannot be used to test an external USB mouse.
3. Tests and Diagnostics After checking T/Pad buttons and cursor’s function, use “Tab” key or use T/Pad cursor to click the “OK” column will end this test. It will indicate whether the subtests pass or fail after three questions. NOTE: The above figure has three compartments although the Touch Pad installed may only have two buttons. In this case, the central compartment in the figure does not correspond to any button.
3.12 LCD Pixels Mode Test 3. Tests and Diagnostics 3. 11 LCD Pixels Mode Test This LCD pixels mode test checks whether video display is fine. This test includes two modes of the test: 1. Text Mode - including 40*25 (16 colors) and 80*25 (2/16colors). 2. VGA Mode - including 320*200 (4/16/256 colors), 640*200 (2/16 colors), 640*350 (2/16 colors), 640*480 (2/16/256 colors), 800*600 (256 colors) and 1024*768 (256 colors).
3. Tests and Diagnostics 3.13 Magnetic Switch Test 3.12 Magnetic Switch Test The lid switch test checks the lid function of the unit. When LCD cover closed, the lid should enable to turn off the display. Follow below steps to run this test: 1. Close the LCD cover. 2. Open the LCD. Then it will indicate whether the test is passed or failed. 1>.
3. Tests and Diagnostics 2>.
3. Tests and Diagnostics 3.13 LAN Test The LAN test checks the LAN full-duplex environment. NOTE: LAN loopback needs to plug in before test begins. And LAN information will show on the test screen: IO Base – Port: A000H IRQ – BH, it’s “IRQ 10”. Node – it is “MAC Address”. Line Frame – 1514 Bytes. Line Speed – 100Mbps or 10 Mbps. Bus ID – it’s “4”. The LAN test includes three subtests of the: 1. Speed1000 2. Speed100 3. Speed10 The subtests run automatically.
3. Tests and Diagnostics The screen should display as below, indicating whether the subtests pass or fail when finished.
3.
3. Tests and Diagnostics 3.14 RTC Test Checks the computer’s RTC (Real Time Clock) and calendar functions by comparing the DOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished.
3. Tests and Diagnostics 3.15 Read 1394 GUID This test will check if the computer’s EEPROM 1394GUID code is correct. NOTE: Must open the RAM Door to see RAM connector GUID bar code before test item begins.
3. Tests and Diagnostics 3.16 Speaker EQ Type Check&Re-Write This test will check if the computer’s EEPROM EQ type is correct. The EQ Type test includes two subtests of the: 1. Read EQ Type from EEPROM 2. Re-Write EQ Type to EEPROM NOTE: To execute this test, you must select speaker type (Harman or No brand).
3. Tests and Diagnostics 3.17 Button Test The control button test allows the user to manually test each of the five CD control buttons. Key”WWW” need to press first. One will hear one “bi” sound when press”WWW” or “Audio” Sound and continuously “bi” sound for another key test. The figure below will be displayed: Press each of the buttons on the front panel in turn. A yellow bar will appear on the relevant section of the figure if the button passes the test. Press Ctrl +C to quit the test.
3. Tests and Diagnostics 3.18 HDD Test The HDD test allows the user to verify the HDD ok or not. For data security concern, it is necessary to input password - “hard disk” before HDD test starts.
3.
3.
3.
3. Tests and Diagnostics 3.19 Front Edge Logo Because this Model have Front Edge Logo, must set the Front Edge Logo if the unit has this logo, if you select this item, The figure below will be displayed: Please check the units whether have the Front Edge Logo: If have the logo, please key 1 to set the Front Edge Logo. If not have the logo, please key 2 to disable the Front Edge Logo. Please read the notice to check the function be enable or be disable in BIOS setup menu.
3. Tests and Diagnostics Notice: Check logo LED on/off function. 1. If we select “2” to disable the Front Edge logo function by program, there haven’t the item of Front Edge Logo in BIOS Menu, the picture likes below. 2. If we select “1” to enable the Front Edge logo function by program, There have the item of Front Edge Logo in BIOS Menu. 2.1 Select enable to let the Front Edge logo item in enable mode (show as below picture), and then restart the machine, the Front Edge Logo Led will be light. 2.
3. Tests and Diagnostics 3.20 Fingerprint DOS Test This test will check if the computer’s Fingerprint function is OK. NOTE: Execution of this test destroys fingerprint data The subtests run step by step: (As below) Step1. Need you swipe your finger to enroll Step2. Need you swipe your finger 2nd time to enroll. Step3. Need you swipe your finger 3rd time to enroll.
3. Tests and Diagnostics Step4. The test program auto compare 1st, 2nd and 3rd finger then to enroll. Step5. Need you swipe your finger then test program will verify it. Step6. Verify pass, Step7. Need you select your test result to show “PASS” or “Fail”.
3. Tests and Diagnostics 3.21 Clear Fingerprint Test NOTE: Execution of this test destroys fingerprint data Working Instruction: Run command - " HWTEST 0 19 2 2 -cf " to clear all information in TBX module The subtests run step by step: (As below) Step1: Step2: Display Notice for clear registered. Step3: below information was the utility auto run.
3. Tests and Diagnostics Step4: Must to reboot system to make the setting effective. Step5: If you choice “Y”, the system will reboot. If you choice “N”, the system will show Notice again (see be photo). You can press any key to go back test MEMU list.
3. Tests and Diagnostics 3.22 Write DMI When you want to write DMI data, please select which data you want to write, the figure below will be displayed: 1. Write OME string 2. Write Version 3. Write Serial 4.
3. Tests and Diagnostics After write OK, you should reboot the system that can make the setting effective, or you can write next data before reboot system, the figure below will displayed: NOTE: should input correct DMI data, and should reboot the system that can make the setting effective.
3. Tests and Diagnostics 3.
Chapter 4 Replacement Procedures [CONFIDENTIAL]
4
4 Replacement Procedures Chapter 4 Contents 4.1 General .................................................................................................................... 4-1 4.2 Battery ..................................................................................................................... 4-7 4.3 PC Card ................................................................................................................... 4-9 4.4 Memory Card ...........................................
4 Replacement Procedures Figures Figure 4-1 Unlocking the battery lock .............................................................................4-7 Figure 4-2 Removing the battery pack.............................................................................4-7 Figure 4-3 Removing the PC card....................................................................................4-9 Figure 4-4 Installing the PC card ..................................................................................
4 Replacement Procedures Figure 4-31 Removing the display assembly................................................................... 4-29 Figure 4-32 Removing the rubber pads ........................................................................... 4-31 Figure 4-33 Removing the display mask screws ............................................................. 4-32 Figure 4-34 Removing the display mask .........................................................................
4 Replacement Procedures Figure 4-62 Removing the USB board.............................................................................4-53 Figure 4-63 Removing the MDC card screws..................................................................4-54 Figure 4-64 Removing the RJ-11 cable ...........................................................................4-54 Figure 4-65 Removing the MDC card .............................................................................
4 Replacement Procedures 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need to be removed in order to remove others.
4 Replacement Procedures The example below shows FRUs to be removed before the CPU can be removed. The CPU is located on the system board. The USB board and the system fan are attached to the system board. The system board itself is located under the top cover. The keyboard must be removed before the display assembly can be removed. The HDD, expansion memory module, PC card module and ODD in turn need to be removed.
4 Replacement Procedures Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1. 2. Always use the lithium ion battery pack or a backup battery that is authorized by Toshiba or is compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode. Heating or disassembling the battery pack could cause leakage of alkaline solution.
4 Replacement Procedures Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassembly steps. Begin each procedure by removing the AC adaptor and the battery pack as instructed in 4.2. 1. Do not disassemble the computer unless it is operating abnormally. 2. Use only the correct and approved tools. 3.
4 Replacement Procedures Disassembly Procedures The computer has two basic types of cable connectors: Pressure Plate Connectors Standard Pin Connectors To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector’s plastic pressure plate and slide the cable out of the connector. To connect the cable to a Pressure Plate connector, make sure the pressure plate is fully lifted and slide the cable into the connector.
4 Replacement Procedures Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or destroyed parts. The following equipment is necessary to disassemble and reassemble the computer: One M2 Phillips screwdriver to remove and replace screws. One T5 security screwdriver.
4 Replacement Procedures 4.2 Battery Removing the Battery Pack To remove the battery pack from the battery bay, follow these steps: 1. Turn the computer upside down. 2. Unlock the battery compartment lock. Figure 4-1 3. Unlocking the battery lock Slide the battery bay latch to release the battery pack and then remove the battery pack from the bay. Figure 4-2 Removing the battery pack NOTE: For environmental reasons, do not throw away a spent battery pack.
4 Replacement Procedures Installing the Battery Pack To install the battery pack in the battery bay, follow these steps and refer to the figures in the preceding section. WARNING: The battery is a lithium ion battery and can explode if not properly replaced, used, handled or disposed of. Use only batteries recommended by Toshiba as replacements. 1. Slide the battery pack into the battery bay. The battery bay latch will click automatically. 2.
4 Replacement Procedures 4.3 PC Card Removing a PC Card To remove a PC card, follow the steps below: 1. Push the PC card’s eject button. The button pops out when you release it. 2. Push the eject button again to pop the PC card out slightly. 3. Grasp the PC card and pull it out from the slot. Figure 4-3 Removing the PC card 4. Press the eject button back into place, if necessary.
4 Replacement Procedures Inserting the PC Card To insert a PC card, follow the steps below: 1. Make sure the eject button does not stick out. Push it back into place if required. 2. Insert the PC card in the slot and gently press to ensure a firm connection.
4 Replacement Procedures 4.4 Memory Card Removing a Memory Card To remove a memory card, follow the steps below: 1. Press the memory card gently into the socket until it pops out. Figure 4-5 Pressing the memory card 2. Grasp the memory and remove it.
4 Replacement Procedures Inserting the Memory Card To insert a memory card, follow the steps below: 1. Insert the memory card in the slot and gently press to ensure a firm connection.
4 Replacement Procedures 4.5 HDD CAUTION: When handling the HDD, do not press the top surface. Hold the disk by the sides to prevent damage and loss of data. Figure 4-8 HDD Removing the HDD Modules The Dual HDD feature makes it easy to handle demanding applications while running background applications such as system backup and virus scans. Follow the steps below to remove HDD module: 1. Turn the computer upside down. 2. Release the two black M2.5x4 screws to release the HDD door.
4 Replacement Procedures 3. Pull up and lift the HDD door to remove it. Figure 4-10 Removing the HDD door 4. Pull out the black Mylar tab to remove the HDD unit. Figure 4-11 Removing the HDD 5. Remove the HDD from the HDD case.
4 Replacement Procedures 6. Pull the HDD outwards and remove the four M3x3 black screws that secure the HDD case and bracket to the HDD.
4 Replacement Procedures 4.6 Expansion Memory Removing the Expansion Memory Modules To remove the memory module, make sure the computer is in boot mode before removing the memory module. Remove the battery pack, cables and any optional devices before you start and then follow these steps: 1. Release the black non-separate screw securing the memory module socket cover. Figure 4-13 2. Slide your fingernail or a thin object under the cover and lift it off.
4 Replacement Procedures 3. Push the latches to release the memory module. A spring will force one end of the module up. Figure 4-15 4. Releasing the memory module Grasp the module and pull it out. Figure 4-136 Removing the expansion memory module 5. Repeat steps 3 and 4 to remove the second memory expansion module in the same way. CAUTION: Do not touch the connectors on the expansion memory module or on the computer. Debris on the connectors may cause memory access problems.
4 Replacement Procedures Installing the Expansion Memory Module CAUTION: Do not touch the connectors on the expansion memory module or on the computer. Debris on the connectors may cause memory access problems. Follow these steps to install a memory module: 1. Set the computer to boot mode and turn off the power. 2. Remove the black captive screw, with the RAM door, securing the memory module socket cover. 3. Slide your fingernail or a thin object under the cover and lift it off. 4.
4 Replacement Procedures 4.7 Optical Drive Module Removing the Optical Drive Module To remove the optical drive module, you need to remove the expansion memory module cover first as described in the previous section. Follow the steps below: 1. Turn the computer upside down. 2. Remove the battery and the expansion memory module cover. 3. Remove the black M2x3 screw securing the optical drive module. Figure 4-17 4.
4 Replacement Procedures Installing the Optical Drive Module To install a device in the optical drive module bay, follow the steps below and refer to the figure in the preceding section. 1. Make sure that the expansion memory door is opened and the ODD screw (M2x3, black) is removed. 2. Slide the device into the optical drive module bay. 3. Use the black M2x3 screw to secure the optical drive module. 4. Install the expansion memory modules as described in the preceding section. 5.
4 Replacement Procedures 4.8 Optical Drive This computer may be fitted with a: DVD-ROM device CD-RW/DVD-ROM combo device DVD Super Multi device Disassembling the Optical Drive To disassemble the optical drive, first remove the drive from its module bay as described in the previous section. Next, release the two M2x3 screws from the bracket plate and remove the bracket plate.
4 Replacement Procedures Reassembling the Optical Drive NOTE: The small arrow shown on the metal bracket indicates the top side of the optical bracket. Keep this in mind when removing or installing the drive. To reassemble an optical drive, follow the steps below and refer to the figure in the preceding section. 1. Position the optical drive bracket plate so that it is aligned with the rear panel of optical drive. 2. Secure the optical drive bracket plate with two M2x3 screws. 3.
4 Replacement Procedures 4.9 Keyboard Removing the Keyboard Before removing the keyboard, remove the battery and any optional devices. Follow the steps below to remove the keyboard: 1. Open the display panel. 2. Insert a thin tool such as a flat screwdriver into the gap between the strip cover and keyboard to lever the strip cover up. Figure 4-20 Removing the strip cover NOTE: The display panel must be fully open in order to remove the strip cover. 3. Remove the strip cover.
4 Replacement Procedures 4. Remove the two black M2.5x2.5 black screws securing the keyboard. Figure 4-22 Removing the keyboard screws 5. Push the center of the keyboard, press the center tab, and lift the keyboard out, revealing the keyboard cable underneath. Disconnect the keyboard cable from the system board.
4 Replacement Procedures 6. Lift and remove the keyboard. Figure 4-24 Removing the keyboard Installing the Keyboard To install the keyboard, follow the steps below and refer to the figures in the preceding section. 1. Connect the keyboard cable to the system board. 2. Clip the keyboard back into its fitting. 3. Place the keyboard on the top cover, insert under the center tab, and secure it with two black M2.5x2.5 screws. 4.
4 Replacement Procedures 4.10 Display Assembly Removing the Display Assembly To remove the display assembly, first remove the battery and any optional devices. Also remove the keyboard, as described in the previous sections. Then follow the steps below: 1. Turn over the laptop. Remove seventeen (17) M2.5x8 screws securing the bottom cover, and three M2x3 screws from inside the battery compartment. Figure 4-25 Removing screws from the bottom cover 2. Turn the laptop over. Remove four M2.
4 Replacement Procedures 3. Disconnect the right and left speaker cables, Bluetooth cable, FPC cable, touch pad cable, function button cable and microphone cable from the system board. Figure 4-27 Disconnecting cables 4. First remove the CMOS cable, then remove the top cover.
4 Replacement Procedures 5. Disconnect the microphone cable, WLAN cable, and LVDS cable from the system board. Carefully disconnect all cables and place them to the side of the notebook. Figure 4-29 Disconnecting cables 6. Remove two hexagonal VGA screws from the CRT module on the left side of the laptop. Remove three M2.5x6 screws securing the LCD assembly to the bottom cover.
4 Replacement Procedures 7. Lift and remove the LCD assembly.
4 Replacement Procedures Installing the Display Assembly To install the display assembly, follow the steps below and refer to the figures in the preceding section. 1. Seat the display assembly, taking care not to crush to the LCD display cable, the CMOS cable, the WLAN cables, the Bluetooth connector, and the microphone cable. 2. Secure three M2.5x6 screws at each hinge to connect the assembly to the bottom cover. 3.
4 Replacement Procedures 4.11 Display Mask Removing the Display Mask To remove the display mask, first remove the display assembly as described earlier, and then follow the steps below: 1. Remove four rubber pads to reveal the four M2.5x6 screws securing the display mask to the LCD module. Figure 4-32 2. Removing the rubber pads Remove the four M2.5x6 black screws securing the display mask.
4 Replacement Procedures Figure 4-33 4-32 Removing the display mask screws Minnesota 10A/10AG Series Maintenance Manual
4 Replacement Procedures 3. Carefully insert your fingers between the display mask and the LCD panel, and pry open the latches. Start with the four latches at the top of the display mask. Continue releasing the latches along the two sides and the bottom edge to remove the display mask. Figure 4-34 Removing the display mask Installing the Display Mask To install the display mask, follow the steps below and refer to the figures in the preceding section. 1.
4 Replacement Procedures 4.12 FL Inverter Board Removing the FL Inverter Board To remove the FL inverter board, first remove the battery pack, display assembly, and display mask; then follow the steps below. 1. Remove the M2x3 black screw securing the FL inverter board to the LCD display assembly. Figure 4-35 Removing the screw NOTE: If a dual inverter board is installed, you must remove two additional M2.5x4 screws. 2. Disconnect the two connectors on either side of the board.
4 Replacement Procedures 3. Remove the FL inverter board. Figure 4-37 Removing the FL inverter board Installing the FL Inverter Board To install the FL inverter board, follow the steps below and refer to the figure in the preceding section. 1. Place the FL inverter board on the LCD module. 2. Secure one M2x3 black screw connecting the FL inverter board to the LCD display assembly. NOTE: If a dual inverter board is installed, you must secure it with two additional M2.5x4 screws. 3.
4 Replacement Procedures 4.13 LCD Module Removing the LCD Module To remove the LCD module, first remove the display assembly, display mask, and FL inverter board and then follow the steps below. 1. Disconnect all cables from the guides around the edge of the top chassis. Figure 4-38 Removing the LCD Module 2. Remove four M2.5x4 screws securing the top chassis to the LCD module, and four A M2.5x5 ○ B M2.5x4 M2.5x5 screws securing the hinges to the LCD module.
4 Replacement Procedures 3. Lift the LCD module from the top chassis. Figure 4-40 Removing the LCD Module 4. Remove six M2x3 screws securing the LCD module bracket to the LCD module. Figure 4-41 Removing the bracket screws NOTE: If the LCD module malfunctions, remove the LCD cable and LCD bracket. Then replace the whole LCD module unit.
4 Replacement Procedures 5. Turn the LCD screen over and remove the tape securing the LVDS cable. Disconnect the LVDS cable. Figure 4-42 Removing the LVDS cable Installing the LCD Module To install the LCD module, follow the steps below and refer to the figures in the preceding section. 1. Secure the LVDS cable to the LCD module. 2. Ensure all cables are outside of the LCD display casing 3. Seat the LCD module in the display assembly with the LCD module bracket and secure it with six M2x3 black screws.
4 Replacement Procedures 4.14 WLAN antennas To remove the WLAN antennas, first remove the display assembly, display mask, FL inverter board and the LCD display module. Then follow the steps below. 1. Remove the three square tabs securing the WLAN antennas. Figure 4-43 Removing the WLAN antennas Installing the WLAN antennas To install the WLAN antennas, follow the steps below and refer to the figures in the preceding sections. 1. Replace the tabs noting the markings on the LCD cover.
4 Replacement Procedures 4.15 Camera and Microphone To remove the camera and microphone, first remove the display assembly, display mask, FL inverter board and the LCD display module. Then follow the steps below. 1. Remove the CMOS cable from the camera module. Remove the camera module by gently peeling it away from its adhesive backing. Figure 4-44 Removing the CMOS cable & camera 2. Use a flat screwdriver to lever the microphone module from its housing and gently lift it out.
4 Replacement Procedures Installing the Camera and Microphone To install the camera and microphone, follow the steps below and refer to the figures in the preceding sections. 1. Secure the camera module to the adhesive backing at the top of the display mask. 2. Connect the CMOS cable to the camera module. 3. Press the microphone into place in its housing.
4 Replacement Procedures 4.16 Bluetooth module To remove the Bluetooth module, first remove the display assembly, keyboard, and top cover. Then follow the steps below: Removing the Bluetooth Module 1. Turn the top cover over. Remove the Bluetooth cable from the Bluetooth module. Figure 4-46 Disconnecting the Bluetooth cable 2. Use a flat blade screwdriver to lever the Bluetooth module from the latches and gently lift out.
4 Replacement Procedures Installing the Bluetooth Module To install the Bluetooth module, follow the steps below and refer to the figures in the preceding section. 1. Insert the Bluetooth module into the module holder on the back of the top cover at a 45degree angle. Push down and press into place. 2. Connect the Bluetooth cable to the module and to the system board.
4 Replacement Procedures 4.17 Touch Pad To remove the Touch Pad, first remove the display assembly, keyboard, and top cover. Then follow the steps below: Removing the Touch Pad 1. Turn the top cover over. Remove the Touch Pad cable from the Touch Pad module. Figure 4-48 Removing the touch pad cable 2. Remove one M2.5x4 screw securing the Touch Pad Bracket to the top cover.
4 Replacement Procedures 3. Remove the Touch Pad bracket by sliding it away from you and lifting it gently. Figure 4-50 Removing the touch pad bracket 4. Remove the Touch Pad by lifting it gently. Figure 4-51 Removing the touch pad Installing the Touch Pad To install the Touch Pad, follow the steps below and refer to the figures in the preceding section: 1. Turn the top cover upside down and place the Touch Pad in position. 2.
4 Replacement Procedures 4.18 Fingerprint Module To remove the Fingerprint module, first remove the display assembly, keyboard, and top cover. Then follow the steps below: Removing the Fingerprint Module 1. Turn the top cover over. Remove four M2.0x2.5 screws securing the Fingerprint Module Bracket to the back of the top cover. Follow the numbered order indicated on the bracket. Figure 4-52 Removing the fingerprint module bracket screws 2. Remove the bracket.
4 Replacement Procedures 3. Remove the Fingerprint module by lifting it gently. Figure 4-54 Removing the fingerprint module Installing the Fingerprint Module To install the Fingerprint Module, follow the steps below and refer to the figures in the preceding section: 1. Turn the top cover upside down and place the Fingerprint Module and the Fingerprint Module Bracket in position on top. 2. Secure the Fingerprint Module bracket with four M2.0x2.5 screws. Follow the numbered order indicated on the bracket.
4 Replacement Procedures 4.19 Speakers To remove the speakers, first remove the display assembly, keyboard, and top cover. Then follow the steps below: Removing the Speakers 1. Turn the top cover over. Remove three M2.5x4 screws securing the right speaker to the top cover. Remove three M2.5x4 screws securing the left speaker to the top cover. Figure 4-55 Removing the speaker screws 2. Disconnect the speaker cables.
4 Replacement Procedures 3. Remove the speakers. Figure 4-57 Removing the speakers Installing the Speakers To install the speakers, follow the steps below and refer to the figures in the preceding section. 1. Seat the speaker brackets in the top cover paying attention to the direction markings. 2. Replace the speakers and secure with three M2.5x4 screws on each side. 3. Extend the right speaker cable through the top cover. 4. Turn the top cover over and install it onto the system board. 5.
4 Replacement Procedures 4.20 Function Button Board To remove the function button board, first remove the display assembly, keyboard, and top cover. Then follow the steps below: Removing the Function Button Board 1. Turn the top cover over. Remove three M2.0x2.5 screws securing the function button board to the top cover. Figure 4-58 Removing the Function Button Board screws 2.
4 Replacement Procedures Installing the Function Button Board To install the function button board, follow the steps below and refer to the figures in the preceding section. 1. Place the function button board into the holder on the rear of the top cover at a 45-degree angle. Push down and press into place. 2. Connect the cable to the connector on the system board. 3. Secure the function button board with one M2.0x2.5 screw.
4 Replacement Procedures 4.21 USB Board To remove the USB board, first remove the display assembly, keyboard, and top cover. Then follow the steps below: Removing the USB Board 1. Remove one M2.5x4 screw securing the USB board to the bottom cover. Figure 4-60 Removing the USB board screw 2. Remove the USB board cable.
4 Replacement Procedures 3. Remove the USB board. Figure 4-62 Removing the USB board Installing the USB Board To install the USB board, follow the steps below and refer to the figures in the preceding section: 1. Place the USB board in position. 2. Connect the USB board cable to the system board. 3. Secure the USB board with one M2.5x4 screw.
4 Replacement Procedures 4.22 MDC Card Removing the MDC Card To remove the MDC card, first remove the display assembly, keyboard, and top cover. Then follow the steps below: 1. Remove the two M2.5x2.5 screws securing the MDC card. Figure 4-63 Removing the MDC card screws 2. Disconnect and remove the RJ-11 cable. Figure 4-64 Removing the RJ-11 cable 3. Remove the MDC Card.
4 Replacement Procedures Installing the MDC Card To install the MDC card, follow the steps below and refer to the figures in the preceding section. 1. Seat the MDC card in the system board. 2. Connect the RJ-11 connector and attach the RJ-11 cable to the MDC card. 3. Secure the MDC card with two M2.5x2.5 screws.
4 Replacement Procedures 4.23 Wireless Module Removing the Wireless Module To remove the wireless module, first remove the display assembly, keyboard, and top cover. Then follow the steps below: 1. Remove the two M2x3 screws securing the wireless module to the system board. Figure 4-66 Removing the wireless module screws 2. Remove the wireless module.
4 Replacement Procedures 4.24 System Fan Removing the System Fan To remove the system fan, first remove the display assembly, keyboard, and top cover. Then follow the steps below: 1. Remove the three M2.5x2.5 screws securing the system fan to the system board. Figure 4-68 Removing the system fan screws 2. Disconnect the system fan cable from the system fan board.
4 Replacement Procedures 3. Remove the system fan. Figure 4-70 Removing the system fan Installing the System Fan To install the system fan, follow the steps below and refer to the figures in the preceding section. 1. Seat the system fan in the chassis. 2. Connect the system fan cable to the system board. 3. Replace the three M2.5x2.5 screws securing the system fan to the system board.
4 Replacement Procedures 4.25 System Board Removing the System Board To remove the system board, first remove the display assembly, keyboard, top cover, MDC card, USB board, wireless module, and system fan. Then follow the steps below: 1. Disconnect and remove the VGA cable. Figure 4-71 Removing the VGA cable 2. Disconnect the DC-IN connector from its socket.
4 Replacement Procedures 3. Remove one M2.5x4 screw securing the system board to the bottom cover. Figure 4-73 Removing system board screw 4. Remove the system board.
4 Replacement Procedures Installing the System Board To install the system board, follow the steps below and refer to the figures in the preceding section. 1. Seat the system board in the chassis. 2. Replace one M2.5x4 screw securing the system board to the bottom cover. 3. Connect the DC-IN connector into its socket. 4. Replace the VGA cable.
4 Replacement Procedures 4.26 VGA Board Removing the VGA Board To remove the VGA board, first remove the display assembly, keyboard, top cover, MDC card, USB board, wireless module, system fan, and system board. Then follow the steps below: 1. Turn the system board over and remove the four spring screws securing the VGA heat sink to the VGA board. Follow the order indicated by the numbers on the heat sink to remove the screws. Figure 4-75 Removing the VGA heat sink screws 2.
4 Replacement Procedures 3. Remove the four M2.5x4 screws securing the VGA board to the system board. Figure 4-77 Removing the VGA board screw 4. Remove the VGA board.
4 Replacement Procedures Installing the VGA Board To install the VGA board, follow the steps below and refer to the figure in the preceding section: CAUTION: If you remove the heat sink, use the grease tool (ex. stain remover) to remove the grease on the VGA board and heat sink. Reapply fresh grease before installing the heat sink. 1. Place the VGA board in the chassis and secure with four M2.5x4 screws. 2. Seat the VGA heat sink on top of the VGA board. 3.
4 Replacement Procedures 4.27 CPU Removing the Fan & CPU To remove the heat sink, and CPU, first remove the display assembly, keyboard, top cover, MDC card, USB board, wireless module, system fan, and VGA board. Then follow the steps below: 1. Turn the system board over and remove the four M2.5x4 screws from the heat sink. Follow the order indicated by the numbers on the heat sink to remove the screws. Figure 4-79 2. Removing the heat sink screws Lift and remove the heat sink from the system board.
4 Replacement Procedures 3. Turn the cam on the CPU socket with a flat-blade screwdriver so that the notch on the cam is aligned with the open side of the CPU socket to unlock the CPU Figure 4-81 4. Gently lift out the CPU.
4 Replacement Procedures Installing the CPU To install the CPU, follow the steps below and refer to the figures in the preceding section. CAUTION: If you remove the heat sink, use the CPU grease tool (ex. stain remover) to remove the grease on the CPU and heat sink. Reapply fresh grease before installing the heat sink. 1. Make sure that the notch on the cam is aligned with the open position of the CPU slot. 2. Seat the CPU aligning the triangle mark on the CPU with the one on the CPU socket.
Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling it to prevent damaging it. 1. When installing the LCD module in the display assembly, make sure that you seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
3. If the panel’s surface gets dirty or moist, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a soft cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. CRT Cleaner 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it.
5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module.
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.
Appendix B Appendix B Board Layout B.
B.
Table B-1 System Board ICs (top and bottom) Number Name U5 AMD North Bridge RS690MC/ RX690 U26 ATI South Bridge SB600 U24 EC KB926 U23 LAN transformer U4 RTL8101E/ RTL8111B (Option) U11 Card bus/1394/5-in1 controller TI PCI8402 U29 HD codec ALC268 U30 Amplifier APA2057A U25 Clock Generator ICS9LPRS365BGLFT Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series Maintenance Manual B-3
Table B-2 System Board Connectors (top and bottom) Number Name JP27 CPU Socket JP8 Fan conn. JP31, JP33 DDRII conn. JP26 TV-Out conn. JP23 VGA/B conn. JP37 1394 conn. JP36 5 in 1 Card Reader conn. JP28 RJ45 conn. JP39 Microphone conn. JP38 Headphone conn. JP6, JP18 Speaker conn. JP20 New Card conn. JP7 WLAN conn. JP34 SATA HDD conn. JP29 ODD conn. JP11 Int. Camera conn. JP12 Blue Tooth conn. JP32, JP30 USB conn. JP22 USB/B conn. JP19 Keyboard conn. JP15 TP conn.
Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series Maintenance Manual B-5
C. Appendix C Pin Assignments System Board C.1 JP31,JP33 Table C-1 SODIMM I/F pin assignments (200-PIN) (1/4) Pin No. Signal name I/O Pin No.
Table C-1 SODIMM I/F pin assignments (200-PIN) (2/4) Pin No. Signal name I/O Pin No.
Table C-1 SODIMM I/F pin assignments (200-PIN) (3/4) Pin No. Signal name I/O Pin No.
Table C-1 SODIMM I/F pin assignments (200-PIN) (4/4) Pin No. C.2 Signal name I/O Pin No. Signal Name I/O 181 DQ57 I/O 182 DQ61 I/O 183 VSS O 184 VSS O 185 DM7 I/O 186 DQS7# I/O 187 VSS O 188 DQS7 I/O 189 DQ58 I/O 190 VSS O 191 DQ59 I/O 192 DQ62 I/O 193 VSS O 194 DQ63 I/O 195 SDA I/O 196 VSS O 197 SLC I/O 198 SA0 O 199 VDDSPD O 200 SA1 O JP24 Table C-2 CRT I/F pin assignments (12-pin) Pin No.
C.3 JP34 Table C-3 HDD I/F pin assignments (22-pin) Pin No. C.4 Signal name I/O Pin No. Signal Name 1 GND 2 A+ 3 A- 4 GND 5 B- 6 B+ 7 GND 8 VCC3.3 9 VCC3.3 10 VCC3.3 11 GND 12 GND 13 GND 14 VCC5 15 VCC5 16 VCC5 17 GND 18 NC 19 GND 20 NC 21 NC 22 NC I/O JP29 Table C-4 ODD I/F pin assignments (52-pin) Pin No. Signal name I/O Pin No.
23 GND - 24 IDE_DIOR# O 25 IDE_DIOW# O 26 GND O 27 IDE_DIORDY I 28 IDE_DDACK# O 29 IDE_IRQ I 30 NC O 31 IDE_DA1 O 32 +5VS I 33 IDE_DA0 O 34 IDE_DA2 I 35 IDE_DCS1# O 36 IDE_DCS3# - 37 SHDD_LED# I 38 +5VS O 39 +5VS - 40 +5VS - 41 +5VS - 42 +5VS - 43 GND - 44 GND - 45 GND - 46 GND - 47 SD_CSEL - 48 GND - 49 NC - 50 NC - 51 GND - 52 GND - C.5 JP5 Table C-5 Mini-Express (3G) I/F pin assignments (52-pin) Pin No.
25 PCIE_PTX_C_ IRX_P5 I/O 26 GND - 27 GND - 28 NC - 29 GND - 30 ICH_SMBCLK I/O 31 PCIE_ITX_C_ PRX_N5 I/O 32 SMBDATA I/O 33 PCIE_ITX_C_ PRX_P5 I/O 34 GND 35 GND - 36 USB20_N2 I/O 37 GND - 38 USB20_P2 I/O 39 +3VS - 40 GND - 41 +3VS - 42 3G_LED - 43 GND - 44 NC - 45 NC - 46 NC - 47 NC - 48 NC - 49 NC - 50 GND - 51 NC - 52 +3VS O - C.6 JP7 Table C-6 Mini-Express (WLAN) I/F pin assignments (52-pin) Pin No.
C7 25 PCIE_PTX_C_IRX _P3 O 26 GND - 27 GND - 28 +1.5VS O 29 GND - 30 ICH_SMBCLK I/O 31 PCIE_ITX_C_PRX _N3 I 32 ICH_SMBDAT A I/O 33 PCIE_ITX_C_PRX _P3 I 34 GND - 35 GND - 36 USB20_N3 O 37 NC - 38 USB20_P3 O 39 NC - 40 GND - 41 NC - 42 NC - 43 NC - 44 NC - 45 NC - 46 NC - 47 NC - 48 +1.5VS O 49 E51_TXD I 50 GND - 51 E51_RXD I 52 +3VS_MINI O JP19 Table C-7 K/B connector pin assignments (34-pin) Pin No.
C.8 19 KSO13 O 20 KSO7 O 21 KSO6 O 22 KSO14 O 23 KSO5 O 24 KSO3 O 25 KSO4 O 26 KSO0 O 27 KSO1 O 28 KSO2 O 29 +3VS O 30 NC - 31 NC - 32 NC - 33 NC - 34 +3VS O JP8 Table C-8 Fan I/F pin assignments (3-pin) C.9 Pin No. Signal name I/O Pin No. 1 +FAN1_VOUT I 2 3 GND - Signal Name FANSPEED1 I/O O JP14 Table C-9 MDC Connector pin assignments (12-pin) Pin No. Signal name I/O Pin No.
C.10 PJP1 Table C-10 AC Adaptor Connector pin assignments (4-pin) Pin No. C.11 Signal name I/O Pin No. Signal Name I/O 1 DC_IN_S1 I 2 DC_IN_S2 - 3 GND - 4 GND - JP39 Table C-11 Microphone I/F pin assignments (6-pin) Pin No. C.12 Signal name I/O Pin No. Signal Name I/O 1 GND - 2 MIC1_L I 3 MIC1_R I 4 MIC_SENSE I 5 GND - 6 NC - JP38 Table C-12 Head phone Connector pin assignments (6-pin) Pin No. Signal name I/O Pin No.
C.13 JP23 Table C-13 VGA/B Connector pin assignments (200-PIN) (1/4) Pin No. Signal name I/O Pin No. Signal Name I/O 1 B+ O 2 +1.8VS O 3 B+ O 4 +1.8VS O 5 B+ O 6 +1.8VS O 7 B+ O 8 +1.8VS O 9 B+ O 10 +1.8VS O 11 B+ O 12 +1.8VS O 13 B+ O 14 +1.8VS O 15 B+ O 16 +1.8VS O 17 B+ O 18 +1.8VS O 19 NC - 20 +1.8VS O 21 +3VS O 22 +1.8VS O 23 +3VS O 24 +1.8VS O 25 +3VS O 26 +1.8VS O 27 +1.5VS O 28 +1.8VS O 29 +1.5VS O 30 +1.
Table C-13 VGA/B Connector pin assignments (200-PIN) (2/4) Pin No. Signal name I/O Pin No.
Table C-13 VGA/B Connector pin assignments (200-PIN) (3/4) Pin No. Signal name I/O Pin No.
Table C-13 VGA/B Connector pin assignments (200-PIN) (4/4) Pin No. Signal name I/O Pin No. Signal Name I/O 181 GND - 182 VGA_TZOUT0+ O 183 +5VALW O 184 GND - 185 +CRT_VCC O 186 VGA_TZOUT1- O 187 +CRT_VCC O 188 VGA_TZOUT1+ O 189 SUSP# I 190 GND - 191 VGA_ENVDD O 192 VGA_TZOUT2- O 193 VGA_ENBKL O 194 VGA_TZOUT2+ O 195 SW_RST# O 196 GND - 197 VGA_TV_LUMA O 198 VGA_TZCLK- O 199 VGA_TV_CRMA O 200 VGA_TZCLK+ O C.
C.16 JP36 Table C-16 5 in 1 Card Reader Connector pin assignments (44-pin) Pin No. Signal name I/O Pin No.
C.17 JP20 Table C-17 New Card Connector pin assignments (26-pin) Pin No. C.18 Signal name I/O Pin No. Signal Name I/O - 2 USB20_N9 I/O I/O 4 CP_USB# O - 1 GND 3 USB20_P9 5 NC - 6 NC 7 ICH_SMBCLK O 8 ICH_SMBDATA I/O 9 +1.5VS_CARD O 10 +1.
C.19 JP15 Table C-19 TP Connector pin assignments (12-pin) Pin No. C.20 Signal name I/O Pin No. Signal Name I/O 1 +5VS O 2 +5VS O 3 TP_DATA I/O 4 TP_CLK O 5 GND - 6 GND - 7 SW_R O 8 NC - 9 NC - 10 NC - 11 NC - 12 SW_L O JP11 Table C-20 Int. Camera Connector pin assignments (5-pin) Pin No. C.21 Signal name I/O Pin No. Signal Name 1 +5VS O 2 USB20_N8 3 USB20_P8 I/O 4 GND 5 GND I/O I/O - - JP16 Table C-21 Int.
C.22 JP28 Table C-22 RJ45 Connector pin assignments (12-pin) Pin No. C.23 Signal name I/O Pin No. Signal Name I/O 1 RJ45_MIDI0+ I/O 2 RJ45_MIDI0- I/O 3 RJ45_MIDI1+ I/O 4 RJ45_MIDI2+ I/O 5 RJ45_MIDI2- I/O 6 RJ45_MIDI1- I/O 7 RJ45_MIDI3+ I/O 8 RJ45_MIDI3- I/O 9 +3V_LAN O 10 LAN_LINK# O 11 +3V_LAN O 12 LAN_ACTIVITY# O JP12 Table C-23 Blue Tooth Connector pin assignments (10-pin) Pin No. C.24 Signal name I/O Pin No.
C.26 JP22 Table C-26 USB/B Connector pin assignments (12-pin) Pin No. C.27 Signal name I/O Pin No. Signal Name I/O 1 +USB_VCCA O 2 +USB_VCCA O 3 +USB_VCCA O 4 +USB_VCCA O 5 USB20_P1 I/O 6 USB20_N1 I/O 7 GND - 8 USB20_P0 I/O 9 USB20_N0 I/O 10 GND - 11 GND - 12 GND - JP30 Table C-27 USB Connector pin assignments (4-pin) Pin No. C.28 Signal name I/O Pin No.
Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (2/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (3/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (4/4) Cap No. Keytop Code set 1 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 X Fn — — — — *4 X Win E0 5B E0 DB E0 1F E0 F0 1F x App E0 5D E0 DD E0 2F E0 F0 2F Make Code set 2 Break Make Note Break Notes: 1. 2. 3. 4. 5. 6. 7. * * * * * * * Scan codes differ by mode. Scan codes differ by overlay function.
Table D-2 Scan codes with left Shift key Cap Key Code set 1 No.
Table D-3 Scan codes in Numlock mode Cap Key Code set 1 No.
Table D-5 Scan codes in overlay mode Cap No. Code set 1 Keytop Code set 2 Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F0 72 39 L (3) 51 D1 7A F0 7A 40 ; (+) 4E CE 79 F0 79 52 M (0) 52 D2 70 F0 70 54 . (.
Table D-7 No.126 key scan code Key top Pause Shift Code set 1 Code set 2 Make Make Common E1 1D 45 E1 Ctrl E0 46 E0 C6 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
Appendix E Key Layout 1. United Status (US) Keyboard Figure US keyboard 2.
3. Thai (TI) Keyboard Figure TI keyboard 4.
5. United Kingdom (UK) Keyboard Figure UK keyboard 6.
7. Hebrew (HB) Keyboard Figure HB keyboard 8.
9. Swiss (SW) Keyboard Figure SW keyboard 10.
11. Czech (CZ) Keyboard Figure CZ keyboard 12.
13. Portuguese (PO) Keyboard Figure PO keyboard 14.
15. Italian (IT) Keyboard Figure IT keyboard 16.
17. German (GR) Keyboard Figure GR keyboard 18.
19. Canada French (CF) Keyboard Figure CF keyboard 20.
21. Spanish (SP) Keyboard Figure SP keyboard 22.
3. Turkish F (TF-F) Keyboard Figure TF-F keyboard 24.
25. Belgian (BE) Keyboard Figure BE keyboard 26.
27. Norwegian (NW) Keyboard Figure NW keyboard 28.
29. Canadian Multinational (AC) Keyboard Figure AC keyboard 30.
31.
F. Appendix F Series Screw Torque List (IALAA) Table F-1 Series Screw Torque List (High-end) SCREW P/N SCREW SPEC Q'ty MAAA00153G0 M2.0*3 6 MA0000061G0 MAC925005G0 M2.5*4 M2.5*5 4 2 MAAA00153G0 M2.0*3 1 MAC925005G0 M2.5*5 1 MAC925005G0 M2.5*5 1 MACAJ0602G0 M2.0*2.5 1 MA0000062G0 M2.5*6 4 MA000008YG0 MA000008YG0 MA000008YG0 MA000008YG0 M2.0*5 M2.0*5 M2.0*5 M2.0*5 2 2 2 2 MA000008YG0 M2.0*5 2 MAAA00153G0 M2.
Table F-2 Series Screw Torque List (Low-end) SCREW P/N SCREW SPEC M2.0*3 M2.5*2.5 M2.5*4 M2.5D Q'ty MAAA00153G0 MAC925025G0 MA0000061G0 MA0000035G0 MA000009EG0 MAAA00153G0 MAAA00153G0 M2.0*3 M2.0*3 3 2 4 1 2 1 6 MA0000061G0 MAC925005G0 MAAA00153G0 MAC925005G0 M2.5*4 M2.5*5 M2.0*3 M2.5*5 4 2 1 1 MAC925005G0 M2.5*5 1 MACAJ0602G0 M2.0*2.5 1 MA0000062G0 M2.5*6 4 MA000008YG0 MA000008YG0 MA000008YG0 MA000008YG0 M2.0*5 M2.0*5 M2.0*5 M2.0*5 2 2 2 2 MA000008YG0 M2.
Satellite A210/ A215, Satellite Pro A210, EQUIUM A210, SATEGO A210 Series Maintenance Manual F-3
Appendix G Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component.
