Maintenance Manual
Table Of Contents
- Qosmio F30 Series Maintenance Manual
- Table of Contents
- SAFETY PRECAUTIONS
- Chapter 1 Hardware Overview
- Chapter 2 Troubleshooting Procedures
- Table of Contents
- 2.1 Troubleshooting
- 2.2 Troubleshooting Flowchart
- 2.3 Power Supply Troubleshooting
- 2.4 System Board Troubleshooting
- 2.5 USB FDD Troubleshooting
- 2.6 2.5” HDD Troubleshooting
- 2.7 Keyboard Troubleshooting
- 2.8 Touch pad Troubleshooting
- 2.9 Display Troubleshooting
- 2.10 Optical Disk Drive Troubleshooting
- 2.11 Modem Troubleshooting
- 2.12 LAN Troubleshooting
- 2.13 Wireless LAN Troubleshooting
- 2.14 Bluetooth Troubleshooting
- 2.15 Sound Troubleshooting
- 2.16 TV tuner Troubleshooting
- 2.17 Bridge media Slot Troubleshooting
- 2.18 Fingerprint sensor
- Chapter 3 Tests and Diagnostics
- Table of Contents
- 3.1 The Diagnostic Test
- 3.2 Executing the Diagnostic Test
- 3.3 Check of the RAID configuration
- 3.4 Setting of the hardware configuration
- 3.5 Heatrun Test
- 3.6 Subtest Names
- 3.7 System Test
- 3.8 Memory Test
- 3.9 Keyboard Test
- 3.10 Display Test
- 3.11 Floppy Disk Test
- 3.12 Printer Test
- 3.13 Async Test
- 3.14 Hard Disk Test
- 3.15 Real Timer Test
- 3.16 NDP Test
- 3.17 Expansion Test
- 3.18 CD-ROM/DVD-ROM Test
- 3.19 Error Code and Error Status Names
- 3.20 Hard Disk Test Detail Status
- 3.21 ONLY ONE TEST
- 3.22 Head Cleaning
- 3.23 Log Utilities
- 3.24 Running Test
- 3.25 Floppy Disk Drive Utilities
- 3.26 System Configuration
- 3.27 Wireless LAN Test Program (Atheros)
- 3.28 Wireless LAN Test Program (Intel-made a/b/g)
- 3.29 Sound/LAN/Modem Test Program
- 3.30 IEEE 1394 Test Program
- 3.31 Bluetooth Test program
- 3.32 SETUP
- 3.33 Thermal Radiation Control Test
- Chapter 4 Replacement Procedures
- Table of Contents
- 4.1 Overview
- 4.2 Battery pack
- 4.3 PC card/Bridge media
- 4.4 HDD
- 4.5 Memory module
- 4.6 Keyboard
- 4.7 MDC
- 4.8 Wireless LAN card
- 4.9 Bluetooth module
- 4.10 Cover assembly
- 4.11 Touch pad
- 4.12 LED board
- 4.13 Fingerprint sensor board
- 4.14 Volume board
- 4.15 Switch membrane
- 4.16 Wireless communication switch
- 4.17 Optical disk drive
- 4.18 RTC battery
- 4.19 Internal microphone
- 4.20 Jack board
- 4.21 System board/DC-IN jack
- 4.22 Speaker
- 4.23 Modem jack/F jack
- 4.24 GPU Fan
- 4.25 Battery lock/Battery latch
- 4.26 Analog TV tuner
- 4.27 CPU fan/CPU heat sink/CPU
- 4.28 GPU heat sink
- 4.29 North bridge heat sink
- 4.30 PC card slot
- 4.31 LCD unit/FL inverter
- 4.32 LCD cable
- 4.33 Wireless LAN antenna/Bluetooth antenna
- 4.34 Latch assembly
- 4.35 Display rear cover
- 4.36 Hinge
- 4.37 Fluorescent lamp
- Appendices
- Table of Contents
- Appendix A Handling the LCD Module
- Appendix B Board Layout
- Appendix C Pin Assignment
- C.1 CN1410 Memory B Connector (200-pin)
- C.2 CN1400 Memory A connector (200-pin)
- C.3 CN1810 ODD I/F connector (50-pin)
- C.4 CN1850 1st HDD I/F connector (22-pin)
- C.5 CN1860 2nd HDD I/F connector (22-pin)
- C.6 CN2110 PC card I/F connector (150-pin)
- C.7 IS2101 Bridge media I/F connector (42-pin)
- C.8 CN2400 WW Tuner I/F connector (124-pin)
- C.9 CN2450 BC board I/F connector (8-pin)
- C.10 CN2600 Wireless LAN card I/F connector (52-pin)
- C.11 CN3010 MDC I/F connector (12-pin)
- C.12 CN3200 Keyboard I/F connector (34-pin)
- C.13 CN3201 Touch Pad I/F connector (4-pin)
- C.14 CN3330 Volume I/F connector (3-pin)
- C.15 J4100 Network I/F connector (12-pin)
- C.16 CN4200 1394 I/F connector (4-pin)
- C.17 CN4400 Bluetooth I/F connector (20-pin)
- C.18 CN4610 USB I/F connector Port5/Port7 (8-pin)
- C.19 CN4611 USB I/F connector Port0/Port4 (8-pin)
- C.20 CN5500 LCD I/F connector (40-pin)
- C.21 CN5080 RGB I/F connector (15-pin)
- C.22 CN5501 S-video OUT connector (4-pin)
- C.23 CN5502 D-video I/F connector (14-pin)
- C.24 CN6170 Speaker connector (4-pin)
- C.25 CN8800 DC IN connector (4-pin)
- C.26 CN8810 Battery connector (10-pin)
- C.27 CN9990 RTC battery connector (3-pin)
- C.28 CN8771 CPU FAN connector (4-pin)
- C.29 CN8781 VGA FAN connector (4-pin)
- C.30 CN9500 LE board I/F connector (20-pin)
- C.31 CN9530 FS board I/F connector (6-pin)
- C.32 CN6500 JK board I/F connector (20-pin)
- C.33 CN9650 SW board I/F connector (20-pin)
- C.34 CN6510 System board I/F connector (20-pin)
- C.35 CN6050 Internal microphone connector (2-pin)
- C.36 J6051 External microphone connector (6-pin)
- C.37 DS6320 Headphone connector (9-pin)
- C.38 CN9612 TV-in connector (5-pin)
- C.39 J9614 AV-in connector (12-pin)
- C.40 CN9510 System board I/F connector (20-pin)
- C.41 CN3250 System board I/F connector (4-pin)
- C.42 CN3251 Touch pad I/F connector (12-pin)
- C.43 CN9660 System board I/F connector (20-pin)
- C.44 CN9540 System board I/F connector (6-pin)
- Appendix D Keyboard Scan/Character Codes
- Appendix E Key Layout
- Appendix F Wiring Diagrams
- Appendix G BIOS Rewrite Procedures
- Appendix H EC/KBC Rewrite Procedures
- Appendix I Reliability
- Appendix J Maintenance of TOSHIBA RAID
2.4 System Board Troubleshooting 2 Troubleshooting Procedures
QOSMIO F30 Maintenance Manual (960-555) [CONFIDENTIAL] 2-23
Table 2-4 Debug port (Boot mode) error status (2/10)
D port status Inspection items Details
Saving key scan code
Setting TASK_1ms_TSC
Controlling fan
Releasing mute Initializing sound items
(for BEEP)
Making the volume max (model that can
control volume)
When request BIOS, EC/KBC
rewriting
Blinks green (cycle:2s, on:1s, off:1s)
When BIOS renewal is
prohibited
Blinks orange (cycle:8s, on:4s, off:4s) HLT
after BEEP is sounded for 30s (Dport=F00BH)
Prohibition of USB
BEEP
Key input
Waiting for key input
FDC reset
Setting parameters for 2HD(1.44MB)
Reading of first sector, If it is the data of
1.44MB (2HD), the media type is definite.
Setting of parameters for 2DD (720KB)
Retrieval of “CHGBIOSA.EXE” from the root
directory.
Directory start header and calculates the
sector
Read 1 sector of the root directory
Retrieval of entry of “CHGBIOSA.EXE”
/“CHGFIRMA.EXE” from the sector read.
Reading of EXE header of “CHGBIOSA.EXE”
and “CHGFIRMA.EXE”
Key input when error occurred
F009h
Reading CHGBIOSA.EXE /
CHGFIRMA.EXE
Execution of “CHGBIOSA.EXE” and
“CHGFIRMA.EXE”