user manual

ManualsBrandsToshiba ManualsPersonal ComputerToshiba Personal Computer M505

[CONFIDENTIAL]

Toshiba Personal Computer

Satellite M500/M505/M507

Maintenance Manual

TOSHIBA CORPORATION

File Number

Summary of content (250 pages)

PAGE 1
Toshiba Personal Computer Satellite M500/M505/M507 Maintenance Manual TOSHIBA CORPORATION File Number [CONFIDENTIAL]
PAGE 2
Copyright © 2007 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Personal Computer Satellite M500/M505/M507 Maintenance Manual First edition June 2009 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
PAGE 3
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite M500/M505/M507. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention. Each of these messages will be italicized and identified as shown below.
PAGE 4
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite M500/M505/M507 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
PAGE 5
Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type.
PAGE 6
Table of Contents Chapter 1 Hardware Overview 1.1 Features .................................................................... 1-Error! Bookmark not defined. 1.2 System Unit Block Diagram .................................... 1-Error! Bookmark not defined. 1.3 HDD/SSD ................................................................ 1-Error! Bookmark not defined. 1.4 DVD Super Multi Drive........................................... 1-Error! Bookmark not defined. 1.5 Keyboard........................
PAGE 7
2.16 Bluetooth(BTO) Troubleshooting............................ 2-Error! Bookmark not defined. 2.17 3G(BTO) Troubleshooting....................................... 2-Error! Bookmark not defined. 2.18 Camera(BTO) Troubleshooting ............................... 2-Error! Bookmark not defined. Chapter 3 Tests and Diagnostics Tests and Diagnostics .......................................................... 3-Error! Bookmark not defined. 3.1 Model,BIOS and CPU Test....................................
PAGE 8
Chapter 4 Replacement Procedures 4.1 General................................................................... Error! Bookmark not defined. 4.2 Battery pack ........................................................... Error! Bookmark not defined. 4.3 Express card ........................................................... Error! Bookmark not defined. 4.4 HDD module .......................................................... Error! Bookmark not defined. 4.5 Memory module............................
PAGE 9
Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ................................................................................................ B-1 Appendix C Pin Assignments............................................................................................ C-1 Appendix D Keyboard Scan/Character Codes ..................................................................
PAGE 10
1 Hardware Overview Chapter 1 Hardware Overview Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL] 1-1
PAGE 11
1 Hardware Overview Chapter 1 Contents 1.1 Features ...................................................................................................................... 1-4 1.2 System Unit Block Diagram .................................................................................... 1-10 1.3 HDD/SSD ................................................................................................................ 1-15 1.3.1 2.5-inch Hard Disk Drive ...............................................
PAGE 12
1 Hardware Overview Figures Figure 1-1 The front and left view of the computer ............................................................ 1-8 Figure 1-2 System unit configuration .................................................................................. 1-9 Figure 1-3 System unit block diagram............................................................................... 1-10 Figure 1-4 2.5-inch HDD...................................................................................................
PAGE 13
1 Hardware Overview 1.1 Features The Toshiba Satellite M500/M505/M507 Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage and high reliability. This computer incorporates the following features. Comment [z1]: Please add below item. 1.eSATA/USB combo port 2.webcam (BTO) 3.SIM card Slot 4.HDMI 5.Headphone/s/PDIF jack 6. Microphone jack 7.Bluetooth (BTO) 8.
PAGE 14
1 Hardware Overview  Tray Type DVD Super Multi +-R Double Layer drive  Tray Type DVD Super Multi +-R Double Layer with Label Flash™ drive  Slot Loading Type DVD Super Multi +-R Double Layer drive  Slot Loading Type DVD Super Multi +-R Double Layer with Label Flash™ drive  Display The PC comes with 14.0W WXGA (1366*768) CSV LED backlight.  Keyboard A4 size 86 key (US) and 87 key (UK) keyboard provides a numeric keypad overlay for fast numeric data entry or for cursor and page control.
PAGE 15
1 Hardware Overview  Media Card slot The Media Card Slot can accommodate all types of media (SD/Mini SD (card adapter is needed)/Micro SD (card adapter is needed)/SDHC memory card/MMC/Memory stick/Memory stick PRO/memory stick pro duo (card adapter is needed)/XD) with various capacities. Media cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, which use Media Card flash-memory.
PAGE 16
1 Hardware Overview  Webcam Module (BTO) The computer is equipped with a webcam module which is embedded to transfer video data – to take still image and offer video stream for end user to preview/record motion image through USB 2.0 interface.  SIM card slot A user accessible SIM card slot is provided behind battery.  HDMI port A HDMI port is provided which complies with the HDMI 1.3 standard.  Headphone / S/PDIF jack The computer is equipped with a headphone jack which is shared with S/PDIF jack.
PAGE 17
1 Hardware Overview The front of the computer is shown in figure 1-1. Figure 1-1 The front and left view of the computer 1-8 [CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual Comment [z11]: Please use the more detail photo to show computer and system unit configuration.
PAGE 18
1 Hardware Overview The system unit configuration is shown in figure 1-2.
PAGE 19
1 Hardware Overview 1.2 System Unit Block Diagram Figure 1-3 is a block diagram of the system unit.
PAGE 20
1 Hardware Overview Comment [z12]: Please add BIOS ROM (Flash EEP ROM) information. The system unit is composed of the following major components: Comment [z13]: Please add core speed detail.  Processor  Intel® Core2 Duo Processor, Intel® Pentium® Dual-Core mobile processor or Mobile Intel® Celeron Processor  Core speed: Intel® Core2 Duo mobile processors: 3.06GHz(T9900), 2.8GHz(P9700), 2.8GHz (T9600), 2.66GHz (P8800), 2.53GHz (P8700), 2.26GHz (P7550), 2.2GHz (T6600), 2.1GHz (T6500), 2.
PAGE 21
1 Hardware Overview  Memory Module – 200 pin, SO Dual In-line Memory Module (SO-DIMM) – PC6400 – 1GB (1,024MB), 2GB (2,048MB), 4GB (4,096MB)  Intel GMCH (North Bridge)  One Intel® 4 Series Express Chipset is used  Features: – 667/800/1066 MHz FSB – Supports DDR2/DDR3 – 8GB maximum memory support – Internal Graphics Controller: 533MHz core render clock @1.
PAGE 22
1 Hardware Overview – Real-Time Clock: 256-byte battery-backed CMOS RAM – Low Pin Count (LPC) I/F: Supports 2 Master/DMA devices – GPIO – 676-ball 31mm×31mm mBGA Package  Card Reader Controller  One Ricoh R5U230 is used  Futures: – PCI Express I/F – SD/MMC, Memory Stick, XD Card Controller – 48-pin, 6mm×6mm, QFN Package  Sound Controller  Realtek ALC269  Mono Microphone-in and stereo headphone-out shared with SPDIF.
PAGE 23
1 Hardware Overview  One MDC is used  This controller has the following functions: – One RJ11 port – Digital line protection support – V.92 (V.90) 56K Modem/FAX  LAN Controller  Realtek RTL8103EL or RTL8111DL is used (depending on model)  This controller has the following functions: – PCIE I/F – Supports 10/100 Mbps or 10/100/1000 Mbps Ethernet – – One RJ45 port WOL support – Magic Packet support  Wireless LAN  One PCI-E MiniCard is used  Support 802.11 a/b/g/n or 802.
PAGE 24
1 Hardware Overview 1.3 HDD/SSD Comment [z15]: Please add SSD information. 1.3.1 2.5-inch Hard Disk Drive The removable HDD is a random access non-volatile storage device. It has a non-removable 2.5-inch magnetic disk and mini-Winchester type magnetic heads. The computer supports a 160GB, 250GB, 320GB, 400GB and 500GB. The HDD is shown in figure 1-4. Specifications are listed in Table 1-1. Figure 1-4 2.5-inch HDD Table 1-1 2.
PAGE 25
1 Hardware Overview Item Specifications Capacity (GB) Rotational Speed (RPM) Height User Data Sectors Bytes / Sector 1.3.2 400 GB 500 GB 5400 rpm 5400 rpm 9.5 mm 9.5 mm 781,422,768 976,773,168 512 512 SSD The solid-state drive (SSD) is a data storage device that uses solid-state memory to store persistent data. A SSD emulates a hard disk drive interface, thus easily replacing it in most applications. The computer supports a dedicated SSD port with TOSHIBA module type SSD.
PAGE 26
1 Hardware Overview Comment [z16]: Please add DVD drive photo. 1.4 DVD Super Multi Drive This drive is a combination of DVD-ROM and DVD±R/±RW/-RAM Drive. It is full-size and runs either 12cm (4.72-inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. It reads DVDs at maximum 8x speed and CDs at maximum 24x speed.
PAGE 27
1 Hardware Overview The specifications are listed in Table 1-3. Table 1-3 DVD Super Multi drive specifications (1/1) Specifications Item DVD-ROM mode SATA Interface (Mbytes/s) Average access time (ms) Data Buffer Capacity Support Formats 1-18 CD-ROM mode 150 Mbyte/s 180ms Typ. 150ms Typ. 2MB CD-DA, CD-ROM CD-ROM XA Photo CD (Multi-session) Video CD, CD-Extra(CD+), CD-Text DVD-ROM DVD-R DVD-Video DVD-RAM (4.7GB) DVD+R/RW, DVD+R DL DVD-RW(Ver. 1.1/1.
PAGE 28
1 Hardware Overview 1.5 Keyboard The keyboard has 86(US)/87(UK) keys that consist of character keys and control keys, and is in conformity with JIS. The keyboard is connected to a membrane connector on the system board and is controlled by EC. Figure 1-7 is a view of the keyboard.
PAGE 29
1 Hardware Overview 1.6 TFT Color Display The TFT color display consists of 14.0-inch LCD module. The LCD module used for the TFT color display uses a LED backlight as the light source and can display a maximum of 262,144 colors with 1366*768 resolution. Table 1-4 lists the specifications. Table 1-4 LCD module specifications (1/1) Specifications Item 14.0" WXGA (1366*768) CSV type Number of Dots 1-20 1,366 (W) * 768 (H) Dot spacing (mm) 0.2265(H) * 0.2265(V) Display range (mm) 309.4(H) * 173.
PAGE 30
1 Hardware Overview 1.7 Power Supply The power supply provides different voltages to the system board and performs the following functions: 1. Determines that the DC power supply (AC adapter) is connected to the computer. 2. Detects DC output and circuit malfunctions. 3. Controls the battery icon, and DC IN icon. 4. Turns the battery charging system on and off and detects a fully charged battery. 5. Turns the power supply on and off. 6. Provides more accurate detection of a low battery. 7.
PAGE 31
1 Hardware Overview 1.8 Batteries The computer has two types of batteries as follows:  Main battery pack  RTC battery The battery specifications are listed in Table 1-6. Table 1-6 Battery specifications Battery name Material Output voltage Capacity Main battery(6 cell) Lithium-Ion 10.8V 4000 mAh Main battery(12cell) Lithium-Ion 10.8V 9000 mAh Lithium 3.0 V 18 mAh RTC battery 1.8.
PAGE 32
1 Hardware Overview 1.8.2 Battery Charging Control Battery charging is controlled by an embedded controller (EC). The EC controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached to the computer. The system charges the battery. Battery Charge When the AC adaptor is attached, there are two types of charge: When the system is powered off and when the system is powered on. Table 1-7 lists the charging time required for charges.
PAGE 33
1 Hardware Overview Table 1-8 RTC battery charging/data preservation time Status Data preservation period (full charge) 1-24 Time 90 days [CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
PAGE 34
1 Hardware Overview 1.9 AC Adaptor The AC adaptor is also used to charge the battery. Table 1-9 lists the AC adaptor specifications. Table 1-9 AC adaptor specifications for integrated graphic model Parameter Specification 2-pin Power 3-pin 65W Input voltage 100V-240V Input frequency 50Hz–60Hz Input current 1.6A or less (100V-240V) Output voltage 19V Output current 0A to 3.
PAGE 35
2 Troubleshooting Procedures Chapter 2 Troubleshooting Procedures Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL] 2-1
PAGE 36
2 Troubleshooting Procedures Chapter 2 Contents Troubleshooting Procedures......................................................................................... 2-1 2.1 Troubleshooting ......................................................................................................... 2-5 2.2 Troubleshooting Flowchart ........................................................................................ 2-6 2.3 Power Supply Troubleshooting.............................................
PAGE 37
2 Troubleshooting Procedures 2.9 Modem Troubleshooting .......................................................................................... 2-35 Procedure 1 Diagnostic Test Program Execution Check ................................ 2-35 Procedure 2 Connector Check and Replacement Check ................................. 2-36 2.10 LAN Troubleshooting ..............................................................................................
PAGE 38
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2) ......................................................................... 2-7 Tables Table 2-1 Battery icon ........................................................................................................ 2-10 Table 2-2 DC IN icon ......................................................................................................... 2-10 Table 2-3 Error code ...........................................................
PAGE 39
2 Troubleshooting Procedures 2.1 Troubleshooting Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction.
PAGE 40
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determining which FRU is malfunctioning. Before going through the flowchart steps, check the following:  Ask the user if a password is registered and, if it is, ask him or her to enter the password.  Make sure that Toshiba Windows VISTA(TM) is installed on the hard disk. NonToshiba operating systems can cause the computer malfunction.  Make sure all optional equipment is removed from the computer.
PAGE 41
2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (1/2) Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL] 2-7
PAGE 42
2 Troubleshooting Procedures 1 Do typed characters appear correctly? No Perform the Keyboard/Touch pad Troubleshooting Procedures in section 2.6 Yes Use the diagnostic HDD and run the diagnostics test program.(PC reboot is required) Refer to section 3.
PAGE 43
2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The Running Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error, then perform the appropriate troubleshooting procedures as follows: 1. If an error is detected on the system test, memory test, real timer test, perform the Main Board Troubleshooting Procedures in Section 2.4. 2.
PAGE 44
2 Troubleshooting Procedures 15. If an error is detected on camera, perform the camera Troubleshooting Procedures in Section 2.18.
PAGE 45
PAGE 46
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed.
PAGE 47
2 Troubleshooting Procedures Comment [z3]: Please provide more detail how to get Error code. Procedure 2 Error Code Check If the power supply microprocessor detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit.
PAGE 48
2 Troubleshooting Procedures Check 1 Compare the patterns in the hexadecimal error code to the tables below.  Battery 2-12 Error code Meaning N0FB01 FCC、LMD under Spec.
PAGE 49
2 Troubleshooting Procedures  Power ON/OFF Error code Meaning N0FT01 Cannot Boot Up N0FT02 System Hang UP when Boot UP N0FT03 Repeat Boot UP N0FT04 Auto Shutdown N0FT05 System Hang Up when Run-In Test N0FT06 Cannot Power Off by ON/OFF Switch N0FT07 Can't Soft Power ON and Power OFF N0FT08 Power On Error by Battery Input only N0FT09 Reset Key Test Error N0FT0A Can't auto boot up when insert Adaptor N0FT0B Can't boot up by fast key. N0FT0C Can't auto slot on boot up with Slot in ODD.
PAGE 50
2 Troubleshooting Procedures Check 2 In the case of error code N0FT0A:  Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC IN 19 V socket and wall outlet. If the cables are connected correctly, go to the following step:  Connect a new AC adaptor and/or AC power cord, if necessary. If the error still exists, go to Procedure 5. Check 3 In the case of error code N0FB04:  Make sure the battery pack is correctly installed in the computer.
PAGE 51
2 Troubleshooting Procedures Procedure 3 Connection Check The power supply wiring diagram is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from the wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord. If there is no damage, go to Check 2. Check 2 Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC-IN jack socket and AC adaptor inlet/wall outlet, respectively.
PAGE 52
2 Troubleshooting Procedures Procedure 4 Charge Check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5. Check 1 Make sure the AC adaptor and AC power cord is firmly plugged into the DC IN socket and the wall outlet. If these cables are connected correctly, replace the AC adaptor (and/or AC power cord, if necessary).
PAGE 53
2 Troubleshooting Procedures Procedure 5 Replacement Check The main board processor module may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. Check the connection between the AC adaptor and main board and connection. After checking the connections, perform the following Check 1: Check 1 Replace the AC adaptor with a new one. If the AC adaptor is still not functioning properly, perform Check 2.
PAGE 54
2 Troubleshooting Procedures 2.4 Main Board Troubleshooting This section describes how to determine if the main board and CPU are defective or not functioning properly. Start with Procedure 1 and continue with the other procedures as instructed.
PAGE 55
2 Troubleshooting Procedures Procedure 1 Message Check When the power is turned on, the system performs the Power On Self Test (POST) installed in the BIOS ROM. The POST tests each IC on the main board and initializes it.  If an error message is shown on the display, perform Check 1.  If Toshiba MS-DOS or Windows VISTA(TM) is properly loaded, go to Procedure 2. Check 1 If one of the following error messages appears on the screen, press F1 as the message instructs.
PAGE 56
2 Troubleshooting Procedures Check 2 The POST checks the main board. When the POST detects an error, the system stops or an error message appears. If one of the following error messages (1) through (3), (5) or (11) appears, go to Procedure 3. If the error message (12), (13) appears, go to the Keyboard Troubleshooting Procedures in Section 2.7. If the error message (15) appears, go to the HDD Troubleshooting Procedures in Section 2.6. (1). (2). (3). (4). (5). (6). (7). (8). (9). (10). (11). (12). (13).
PAGE 57
2 Troubleshooting Procedures Procedure 2 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform these tests. 1. Check MAIN Ver D. KB Test 2. Model, BIOS and CPU Test E. MEMSIZE Test 3. Check MAC Test F. FNTEST Test 4. ACIN Test G. LEDALL Test 5. Temperature Test H. STORE Test 6. USB Test I. LED/LCDEDID Test 7. USBCCD Test J. MSCARD Test 8. PAD Test K.
PAGE 58
2 Troubleshooting Procedures Procedure 3 Replacement Check The main board connectors may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform Check 1. Check 1 Visually check for the following: a) Cracked or broken connector housing b) Damaged connector pins If their connectors are in good condition, but there is still a problem, go to Check 2. Check 2 2-22 The main board may be damaged.
PAGE 59
2 Troubleshooting Procedures 2.5 HDD/SSD Troubleshooting This section describes how to determine if the HDD/SSD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.
PAGE 60
2 Troubleshooting Procedures Procedure 2 Partition Check Insert the bootable USB key, restart the computer with Esc key pressing down. and choose boot from USB device. Perform the following checks: Check 1 Type C: and press Enter. If you cannot change to drive C, go to Check 2. If you can change to drive C, go to Check 3. Check 2 Type FDISK and press Enter. Choose Display Partition Information from the FDISK menu. If drive C is listed, go to Check 3.
PAGE 61
2 Troubleshooting Procedures Procedure 3 Format Check The computer’s HDD/SSD is formatted using the low level format program and the MS-DOS FORMAT program. To format the HDD/SSD, start with Check 1 below and perform the other steps as required. Check 1 Format the HDD/SSD and transfer system files using FORMAT C:/S/U. If the following message appears on the display, the HDD/SSD is formatted.
PAGE 62
2 Troubleshooting Procedures Procedure 4 Diagnostic Test Program Execution Check The HDD/SSD test program is stored in the Diagnostics Disk. Perform all of the HDD/SSD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD/SSD test program. If an error is detected during the HDD/SSD test, an error code and status will be displayed. Replace the HDD/SSD with a new one following the instructions in Chapter 4, Replacement Procedures.
PAGE 63
2 Troubleshooting Procedures If any of the connections are loose, reconnect firmly and repeat Procedure 1. If there is still an error, go to Check 2. Check 2 The HDD/SSD may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 3. Check 3 The Main board may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures.
PAGE 64
2 Troubleshooting Procedures 2.6 Keyboard and Touch pad Troubleshooting To determine if the computer’s keyboard or touch pad is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Keyboard Test in the Diagnostic Program.
PAGE 65
2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The keyboard, touch pad or sensor/switch board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: 1. If the keyboard or AccuPoint malfunctions, start with Check 1. 2. If the touch pad malfunctions, start with Check 3. 3. If the power switch, InTouch button or Presentation button malfunctions, start with Check 5.
PAGE 66
2 Troubleshooting Procedures If the connection is loose, reconnect firmly. If there is still an error, go to Check 4. Check 4 Check 5 2-30 The touch pad or the touch pad cable may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 5. The main board may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures.
PAGE 67
2 Troubleshooting Procedures 2.7 Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector Check and Cable Check Procedure 4: Replacement Check Procedure 1 External Monitor Check Connect an external monitor and turn on the computer.
PAGE 68
2 Troubleshooting Procedures If the connection is loose, reconnect firmly and restart the computer. If there is still an error, go to Procedure 4. Procedure 4 Replacement Check LCD module and main board are connected to display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Make sure the LVDS cable is firmly connected to CON6201 on the main board.
PAGE 69
2 Troubleshooting Procedures 2.8 Optical Drive Troubleshooting This section describes how to determine if the optical drive (DVD-ROM and DVD±R/±RW/RAM Drive) in the Slim Select Bay is functioning properly. Perform the steps below starting with Procedure 1 and continue with the other procedures as required.
PAGE 70
2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The optical drive (DVD-ROM and DVD±R/±RW/-RAM Drive) is connected to the main board. The connectors may be disconnected from the main board or may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the drive to test is firmly connected to CON6002 on the main board.
PAGE 71
2 Troubleshooting Procedures 2.9 Modem Troubleshooting This section describes how to determine if the computer’s modem is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Insert the LAN/Modem test program in the USB key, turn on the computer and run the test.
PAGE 72
2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The Modem is installed as an MDC (Modem Daughter Card). If the modem malfunctions, there may be a bad connection between the MDC and the main board. Or the MDC, main board or their connectors might be damaged.
PAGE 73
2.10 LAN Troubleshooting 2 Troubleshooting Procedures 2.10 LAN Troubleshooting This section describes how to determine if the computer’s LAN is functioning properly. Perform the steps below starting with Procedure 1 and continue with the other procedures as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 1 Diagnostic Test Program Execution Check Execute the LAN test program available as part of the LAN/Modem test program.
PAGE 74
2 Troubleshooting Procedures 2.11 Wireless LAN Troubleshooting This section describes how to determine if the computer’s Wireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Transmitting-Receiving Check Procedure 2: Antenna Connection Check Procedure 3: Replacement Check Procedure 1 Transmitting-Receiving Check Make sure the wireless switch of the computer is turned “On.” If it is not, please turn it on.
PAGE 75
2 Troubleshooting Procedures Procedure 2 Antenna Connection Check The wireless LAN wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the wireless LAN board is firmly connected to CON5701 on the main board. If the connector is disconnected, connect it firmly. If the wireless LAN board is still not functioning properly, perform Check 2.
PAGE 76
2 Troubleshooting Procedures Procedure 3 Replacement Check The wireless LAN antenna, wireless LAN board and the main board are connected to the circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 The wireless LAN board may be defective or damaged. Replace the board with a new one following the steps in Chapter 4, Replacement Procedures.
PAGE 77
2 Troubleshooting Procedures 2.12 Sound Troubleshooting This section describes how to determine if the computer’s sound functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execution Check Insert the Sound test program in the USB key, turn on the computer and run the test.
PAGE 78
2 Troubleshooting Procedures Procedure 2 Connector Check The sound function-wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: If the stereo speakers do not work correctly, perform Check 1. If the headphone does not work correctly, perform Check 2. If the microphones do not work correctly, perform Check 3.
PAGE 79
2 Troubleshooting Procedures Procedure 3 Replacement Check >>>> Check 1 If the stereo speakers do not sound properly, the right or left speaker may be defective or damaged. Replace it with a new one. If the stereo speakers still do not work properly, go to Check 4. Check 2 If the headphone does not sound properly, the headphone jack may be defective or damaged. Replace it with a new one. If the sound function still does not work properly, go to Check 4.
PAGE 80
2 Troubleshooting Procedures 2.16 SD Card Slot Troubleshooting 2.13 Card Reader Slot Troubleshooting This section describes how to determine if the computer’s card reader functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Check on Windows VISTA(TM) Procedure 2: Connector Check and Replacement Check Procedure 1 Check on Windows VISTA(TM) Insert an MMC/SD/MS/MS(PRO) card into the slot.
PAGE 81
2 Troubleshooting Procedures 2.14 PCI Express Card Slot Troubleshooting This section describes how to check PCI Express Card slot by inspecting a card with PCI Express interface. Procedure 1: Check on Windows VISTA(TM) Procedure 2: Connector Check and Replacement Check Procedure 1 Check on Windows VISTA(TM) Insert a PCI Express Card into the slot. Check if the installed Windows recognizes automatically the PCI Express Card. If the card is not recognized, go to Procedure 2.
PAGE 82
2 Troubleshooting Procedures 2-46 2.
PAGE 83
2 Troubleshooting Procedures 2.15 Fingerprint Board(BTO) Troubleshooting This section describes how to determine if the computer’s fingerprint board is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.
PAGE 84
2 Troubleshooting Procedures Procedure 2 2.16 SD Card Slot Troubleshooting Connector Check and Replacement Check The fingerprint board is installed to the touchpad board. If the fingerprint board malfunctions, there may be a bad connection between the fingerprint board and the touchpad board. Or the fingerprint board or touchpad board might be damaged.
PAGE 85
2 Troubleshooting Procedures 2.16 Bluetooth(BTO) Troubleshooting This section describes how to determine if the computer’s Bluetooth is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Insert the Bluetooth test program in the USB key, turn on the computer and run the test.
PAGE 86
2 Troubleshooting Procedures Procedure 2 2.16 SD Card Slot Troubleshooting Connector Check and Replacement Check The Bluetooth is installed on the main board by Bluetooth cable. If the Bluetooth malfunctions, there may be a bad connection between the Bluetooth and the main board. Or the Bluetooth, main board or the Bluetooth cable might be damaged.
PAGE 87
2 Troubleshooting Procedures 2.17 3G(BTO) Troubleshooting This section describes how to determine if the computer’s 3G is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Insert the 3G test program in the USB key, turn on the computer and run the test.
PAGE 88
2 Troubleshooting Procedures Procedure 2 2.16 SD Card Slot Troubleshooting Connector Check and Replacement Check The 3G is installed as an 3G card. If the 3G malfunctions, there may be a bad connection between the 3G and the main board. Or the 3G or main board might be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the 3G is firmly connected to CON5601 on the main board and the connector of the 3G.
PAGE 89
2 Troubleshooting Procedures 2.18 Camera(BTO) Troubleshooting This section describes how to determine if the computer’s camera is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Insert the camera test program in the USB key, turn on the computer and run the test.
PAGE 90
2 Troubleshooting Procedures Procedure 2 2.16 SD Card Slot Troubleshooting Connector Check and Replacement Check The camera is installed on the main board by camera cable. If the camera malfunctions, there may be a bad connection between the camera and the main board. Or the camera, main board or the camera cable might be damaged.
PAGE 91
3 Tests and Diagnostics Chapter 3 Tests and Diagnostics Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL] 3-1
PAGE 92
3 Tests and Diagnostics Chapter 3 Contents Tests and Diagnostics ..................................................................................................... 3-3 3.0.1 Test menu ............................................................................................. 3-4 3.0.2 Executing the Diagnostic Test.............................................................. 3-5 3.0.3 Executing the Diagnostic Test.............................................................. 3-6 3.
PAGE 93
3 Tests and Diagnostics Tests and Diagnostics This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The test program should be stored on an optical media disk or a USB boot memory. The test program menu will also consist of some programs which test the hardware function or display the current information of the computer. To execute the auto run will automatically run all the test programs.
PAGE 94
3 Tests and Diagnostics 3.0.1 Test menu The Test MENU consists of the following functions. Please enter the item number to choose and execute the test item.
PAGE 95
3 Tests and Diagnostics 3.0.2 Executing the Diagnostic Test To start the Test PROGRAM on CD-ROM, follow these steps: 1. Burn the test program ISO image to an optical media disk. 2. Insert the optical media disk with the test program into optical device. 3. Turn on the power, and choose boot from optical device. 4. System will automatically run the test program and display the test menu. 5. When the test menu displays, please enter the item number to choose and execute the test item.
PAGE 96
3 Tests and Diagnostics 3.0.3 Executing the Diagnostic Test To start the Test PROGRAM on USB boot disk, follow these steps: 1. Please prepare Toshiba PC of Windows VISTA OS. 2. Please copy the file for creating a USB-Bootable memory to PC. The filename of four files and one folder to copy is shown below. a) b) c) d) e) f) COMMAND.COM Freedos.bss FreeDOSMake.exe KERNEL.SYS Autoexec.bat Folder (USBMakingFolder) 3. Please format USB-memory in FAT mode before creating USB-Bootable memory. 4.
PAGE 97
3 Tests and Diagnostics Please check the check box. And then click START. 7. Turn on the Toshiba PC which need test, and choose boot from USB device. 8. System will automatically run the test program and display the test menu. 9. When the test menu displays, please enter the item number to choose and execute the test item. NOTE: Please make sure to set test PC SATA Controller Mode to “Compatibility” in BIOS.
PAGE 98
3 Tests and Diagnostics 3.1 Model,BIOS and CPU Test Note: The screen will pause 10sec then turn to next step.
PAGE 99
3 Tests and Diagnostics 3.1.1 CPU Test Check CPU spec same with your fixture Check Front side bus speed is real (The speed does match that of BIOS setup) This chapter shows how to use the Diagnostics to test the functions of the CPU speed, type and CPU ID code. 3.1.1.1. Diagnostic name: CPU.EXE Diagnostic Version: 2.10 or later version. 3.1.1. 2.Principle and how to use: a. The CPU diagnostic consists of the following functions. The CPU types, internal speed and CPU ID.
PAGE 100
3 Tests and Diagnostics 3.2 Check MAC Test Check MAC address with the label on the motherboard This chapter shows how to use the Diagnostics to test the MAC address of the Ethernet controller. 3.3.1. Diagnostic name: pg8168.exe Diagnostic Version: 2.00 or later version. 3.3.2. Principle and how to use: a. The pg8168 diagnostic consists of the following functions. MAC Address read and checking function. Command line: Pg8168.
PAGE 101
3 Tests and Diagnostics 3.3 ACIN Test Please insert adopter then run this program. This subtest checks if the power port works properly. This chapter shows how to use the Diagnostics to test the ACIN functions. 3.3.1 Plug in the power test program will display PASS 3.3.2 Unplug the power to test the program will show Fail. If it fails in a test item, press “Ctrl+C” and “Y” back to main menu.
PAGE 102
3 Tests and Diagnostics 3.4 Temperature Test Please execute the Temperature Test from test menu. Test program will show the current CPU temperature result on RIO_25Ch line. Temperature Test will also check if system temperature is at 20∘ C ~ 80∘ C.
PAGE 103
3 Tests and Diagnostics 3.5 Web camera Test This program is to check webcamera ID.
PAGE 104
3 Tests and Diagnostics 3.6 PAD Test Press both the Left and Right Buttons three times to see if they work properly. This chapter shows how to use the Diagnostics to test the pointing device functions. 3.8.1. Diagnostic name: PS2.EXE Diagnostic Version: 1.15 or later version. 3.8.2. Principle and how to use: a. The PS2 diagnostic tests the following functions. Right & left button, move function. Move the cursor and click Left and Right button to ensure the pointing device is working normally.
PAGE 105
3 Tests and Diagnostics -t2 : Testing Left and Right button only. -ae : Auto exit the program after the Left and Right button click time setting have reached the setting. /TP2 : PS2 mouse testing, no driver need. b. Please refer to the illustration above to see the Touchpad test information. c. Type “PS2.
PAGE 106
3 Tests and Diagnostics 3.7 LCDRGB Test This subtest displays gradations for following modes. To change the mode, press Enter. Command: video.
PAGE 107
3 Tests and Diagnostics [Mode 111 640*480 16M] [Mode 114 800*600 16M] Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL] 3-17
PAGE 108
3 Tests and Diagnostics 3-18 Manual [CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
PAGE 109
3 Tests and Diagnostics [Mode 105 1024*768 8M] [Mode 117 1024*768 16M] Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL] 3-19
PAGE 110
3 Tests and Diagnostics This chapter shows how to use the Diagnostics to test the LCD RGB/WB functions. 3.9.1. Diagnostic name: VIDEO.EXE Diagnostic Version: 2.25.06 or later version. 3.9.2. Principle and how to use: a. The VIDEO diagnostic tests following functions. LCD test for R,G,B and BW. Command line: video -p -rc /RGB 111 video -p -gc /RGB 111 video -p -bc /RGB 111 -p: To set a pixel mode to display on the screen. -rc | -gc | -bc: To set the color display on the screen.
PAGE 111
3 Tests and Diagnostics 3.8 VGA Test This chapter is part of the test card. This test focus on the function of VGA chip and VRAM. Note: It may occur a blue screen for serveral minutes before 3D test when using a USB disk to test.
PAGE 112
3 Tests and Diagnostics 3.
PAGE 113
3 Tests and Diagnostics 3.10 Keyboard Test Press Fn +F12 to end the test NOTE: Press the Fn + F12 to end the test can only work after pressing all keys on the keyboard. If there are some failure keys which cause the test can not complete, you can NOT use Fn+ F12 to end test program. Please press “Ctrl + Shift” key (press Ctrl first then press Shift). And then release “Ctrl + Shift” key (release Shift first then release Ctrl).
PAGE 114
3 Tests and Diagnostics Command: Keyboard.exe /r trsaeng.map trsaeng.xy trsaeng.cd a. Please choose the different kind of keyboard language. b. Display the keyboard on the screen to indicate to the operator checking whether or not each key is correct. c. Type each key to finish the program.
PAGE 115
3 Tests and Diagnostics 3.11 Memory Test This program will test the memory and shows you the total memory size. Show the total memory size. Command: mm.exe – t 4 /s This chapter shows how to use the Diagnostics to test the functions of the memory size, speed and location. 3.2.2.1 Diagnostic name: SMBUS.
PAGE 116
3 Tests and Diagnostics Diagnostic Version: 1.37 or later version. 3.2.2.2 Principle and how to use: a. The SMBUS diagnostic consists of the following functions. Memory sizes, memory speed and memory location. Command line: a-1. mm -t 4 /s %MSIZE% “-t 3” defines where the memory size will be tested. “/s %MSIZE%” set the memory size. b. Please refer to the illustration above to see the memory information. c. Type “SMBUS.
PAGE 117
3 Tests and Diagnostics 3.12 Function TEST Please enter “C” to select the function test. Test program will test several function and show the test result one by one. (Command: functest.exe /T).
PAGE 118
3 Tests and Diagnostics 3.13 LEDALL Test Test sequnce: 1. PWRBTN_LED white 2. DC-IN LED white 3. PWR_ULED_UP orange 4. PWR_WLED pink 5. BAT_ULED_UP orange 6. BAT_WLED pink 7. LOGO_LED white 8. Light_GI_Led white 9.
PAGE 119
3 Tests and Diagnostics 3.14 STORE Test [CD/DVD-ROM TEST] This Program will test if the CD/DVD-ROM works properly, please insert test CD before test. This chapter shows how to use the Diagnostics to test the ODD functions. 3.17.1. Diagnostic name: PSATA.EXE 3.17.2. Principle and how to use: a. The PSATA diagnostic consists of the following functions. CD/DVD type , CD/DVD F/W.
PAGE 120
3 Tests and Diagnostics 3.15 LID Switch Test Run the test using the instructions in the image below. This chapter shows how to use the Diagnostics to test the LID functions. 3.18.1. Diagnostic name: PMC.EXE Diagnostic Version: 2.05. 3.18.2. Principle and how to use: a. The diagnostic of PMC detects whether the lid SW works or not.
PAGE 121
3 Tests and Diagnostics 3.16 MS CARD Test This chapter shows how to use the Diagnostics to test the card reader functions.
PAGE 122
3 Tests and Diagnostics 3.19.1. Diagnostic name: RMS2XX.EXE Diagnostic Version: 1.02. 3.19.2. Principle and how to use: Diagnostic provided by vendor which is an MS card test program that checks the MS card’s read, write and protect function. a. The diagnostic of RMS2XX detects MS card and read /write data. 3.19.3. Principle and how to use: Copy data into the card and compare with the master file to see if the data matches.
PAGE 123
3 Tests and Diagnostics 3.17 SD CARD Test This chapter shows how to use the Diagnostics to test the card reader functions.
PAGE 124
3 Tests and Diagnostics 3.20.1. Diagnostic name: RSD.EXE Diagnostic Version: 1.02. 3.20.2. Principle and how to use: Diagnostic provided by vendor which is an SD card test program that checks the SD card’s read, write and protect function. a. The diagnostic of RSD detects SD card and read /write data. 3.20.3. Principle and how to use: Copy data into the card and compare with the master file to see if the data matches.
PAGE 125
3 Tests and Diagnostics 3.
PAGE 126
3 Tests and Diagnostics 3.19 BATTERY Test The battery test will provide the relate information of battery. This program can also test the battery charge / discharge function. You can also find the battery cycle count information on this battery. NOTE: Please connect the AC adapter to system in battery charge test.
PAGE 127
3 Tests and Diagnostics 3.
PAGE 128
3 Tests and Diagnostics 3.21 HDD 3D Protection Place computer in five position as screen shows. For Field inspection T&D, this program judges by sampling five kinds of data shown below. No Item Contents 1 Access platform. An access platform is leveling. 2 Test Fixture The Fixture which fixes PC by 60 degree inclination is used. Vibration/shock doesn't take a PCB at the time of T&D inspection. 3 Test1 The display of a test program and the set method of PC are shown below.
PAGE 129
3 Tests and Diagnostics Judgment If all data is less than ranges, it will be OK. 4 Test2 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Rear Upper Judgment If all data is less than ranges, it will be OK.
PAGE 130
3 Tests and Diagnostics 5 Test3 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Right Upper Judgment If all data is less than ranges, it will be OK.
PAGE 131
3 Tests and Diagnostics 6 Test4 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Front Upper Judgment If all data is less than ranges, it will be OK.
PAGE 132
3 Tests and Diagnostics 7 Test5 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Left Upper Judgment If all data is less than ranges, it will be OK. 8 Inspection Judgment If all data is less than ranges, it will be OK. 9 3-42 Manual Setting Calibration data When an inspection result is O.K., calibration at HPC.
PAGE 133
3 Tests and Diagnostics If the position is correct, it will show OK. If the position is wrong, it will show NG.
PAGE 134
3 Tests and Diagnostics 3.22 Speaker Test This program will test left channel, right channel and two wave files to test speaker function.
PAGE 135
3 Tests and Diagnostics 3.12 Read and Write DMI information This program could read and write below strings from/to DMI block. 1. 2. 3. 4. 5. 6.
PAGE 136
3 Tests and Diagnostics Read Type 11: Read Type 12: Write Type 11（60 bytes）: Write Type 12 (64 bytes): 3-46 Manual [CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
PAGE 137
3 Tests and Diagnostics Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL] 3-47
PAGE 138
3 Tests and Diagnostics 3.23 Auto Run Please enter “J” to select the auto run function. Test program will auto run all test items one by one as following sequence.
PAGE 139
3 Tests and Diagnostics 3.
PAGE 140
4 Replacement Procedures Chapter 4 Replacement Procedures SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL] 4-1
PAGE 141
4 Replacement Procedures Chapter 4 4-2 4.1 General ...............................................................................................................6 4.2 Battery pack......................................................................................................14 4.3 Express card......................................................................................................16 4.4 HDD module ................................................................................
PAGE 142
4 Replacement Procedures Figures Figure 4-1 Removing the battery pack....................................................................14 Figure 4-2 Pressing the Express card......................................................................16 Figure 4-3 Removing the HDD cover.....................................................................17 Figure 4-4 Removing 4 screws securing HDD assembly .......................................18 Figure 4-5 Removing the HDD connector..........................
PAGE 143
4 Figure 4-22 Replacement Procedures Removing the LED and Fingerprint Board.........................................37 Figure4-23 Separating fingerprint board assembly.................................................37 Figure 4-24 Removing screw securing touchpad on-off board ..............................39 Figure 4-25 Removing tapes and LVDS screw ......................................................40 Figure 4-26 Removing cables ....................................................................
PAGE 144
4 Replacement Procedures Figure 4-43 Apply new thermal pad on the fan ......................................................58 Figure 4-44 Removing the bezel.............................................................................59 Figure 4-45 Removing the LCD unit ......................................................................60 Figure 4-46 Removing the LCD supports...............................................................61 Figure 4-47 Removing the LCD cable....................
PAGE 145
4 Replacement Procedures 4.1 General This section explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need to be removed in order to remove others.
PAGE 146
4 Replacement Procedures Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1) Always use the genuine battery that is authorized by Toshiba or compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode. Never heat or disassemble the battery pack, as that could cause leakage of alkaline solution.
PAGE 147
4 Replacement Procedures Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassembly steps. Begin each procedure by removing the AC adaptor and the battery pack as instructed in this section: 1. Do not disassemble the computer unless it is operating abnormally. 2. Use only the correct and approved tools. 3.
PAGE 148
4 Replacement Procedures Disassembly Procedures The computer has three basic types of cable connectors:  Pressure Plate Connectors  Coaxial Cable Connectors  Normal Pin Connectors To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector’s plastic pressure plate and slide the cable out of the connector. To connect the cable to a Pressure Plate connector, make sure the pressure plate is fully lifted and slide the cable into the connector.
PAGE 149
4 Replacement Procedures Assembly Procedures After you have disassembled the computer and fixed or repaired the problem that was causing the computer to operate abnormally, you will need to reassemble the computer. Install all the removed FRUs following the steps described in the corresponding sections in this chapter. While assembling the computer, remember the following general points:  Take your time, making sure you follow the instructions closely.
PAGE 150
4 Replacement Procedures Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or destroyed parts. The following equipment is necessary to disassemble and reassemble the computer:  One M2 point size 0 Phillips screwdriver  One M2.
PAGE 151
4 Replacement Procedures Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose. NOTE:  M2 0.167 N·m (1.7 kgf·cm)  M2.5 0.294 N·m (3.0 kgf·cm)  M3 0.549 N·m (5.6 kgf·cm) NOTE: 4-12 Toshiba recommends that you use an electric screwdriver for quick and easy operations.
PAGE 152
4 Replacement Procedures Color of Screw Shaft To avoid mistakes on the screw length, screw shafts are colored as follows:  Even number length screw: brown  Odd number length screw: white  Special length screw: blue (Screws whose lengths are indicated to one or more decimal places such as 2.5 mm or 2.8 mm.
PAGE 153
4 Replacement Procedures 4.2 Battery pack Removing the Battery pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: When handling battery packs, be careful not to short-circuit the terminals. Also do not drop, hit or apply impact, do not scratch, break, twist or bend the battery pack. 1. Turn off the power of the computer. 2. Disconnect the AC adaptor and other external devices from the computer. 3. Turn the computer face down. 4. Release the battery lock.
PAGE 154
4 Replacement Procedures Installing the Battery pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. For environmental reasons, collect the spent battery packs. Use only batteries recommended by Toshiba for replacements. NOTE: Check the battery’s terminals visually. If they are dirty, wipe them clean with a dry cloth. 1.
PAGE 155
4 Replacement Procedures 4.3 Express card Removing the Express card To remove the Express card, follow the steps below and refer to Figure 4-2 to 4-3. CAUTION: Before you remove the Express card, refer to the notebook’s documentation and to your operating system documentation for proper procedures and precautions. 1. Turn the computer face up. 2. Press the Express card pop the Express card out. 3. Grasp the Express card and pull it out.
PAGE 156
4 Replacement Procedures 4.4 HDD module CAUTION: When handling the HDD, do not press the top surface as shown by the arrow. Hold it by the sides. Removing the HDD To remove the HDD, follow the steps below and refer to Figure 4-4 to 4-10. 1. Turn the computer upside down. 2. Loosen the screw (with an e-ring) and remove the HDD cover, underneath which there also installing the memory module. Figure 4-3 Removing the HDD cover 3. Remove the following screws securing HDD module.
PAGE 157
4 Replacement Procedures 4. Pull the tab of the HDD assembly to remove it from the connector of the HDD cable. Be careful not to damage the connector. Figure 4-4 Removing 4 screws securing HDD assembly NOTE: The following steps describe how to disassemble the HDD assembly, however, do not disassemble if the HDD is working properly. 5. Place the HDD assembly on a flat surface, remove the HDD connector and then remove the following screws.
PAGE 158
4 Replacement Procedures 6. Separate the HDD and HDD Holder. CAUTION: Do not apply pressure to the top or bottom of the HDD.
PAGE 159
4 Replacement Procedures Installing the HDD To install the HDD, follow the steps below and refer to Figure 4-3 to 4-6. CAUTION: Do not hold the HDD by its top and bottom flat surfaces. It may damage the HDD. 1. Seat the HDD in the HDD Holder and secure the following screws. M23L FLAT HEAD screw 4 2. Install the HDD connector. 3. Put the HDD into its slot and connect the HDD to the connector. 4. Secure them with the following screws.
PAGE 160
4 Replacement Procedures 4.5 Memory module Removing the Memory module To remove the memory module, make sure the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-7 to 4-8. 1. Press two latches outward and remove the first memory. 2. Press two latches outward and remove the second memory.
PAGE 161
4 Replacement Procedures Installing the Memory module To install the memory module, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-7 to 4-8. CAUTION: When installing only one memory module, be sure to insert it into slot . Otherwise, the computer or the memory may not work properly. Do not touch the connectors on the memory module or on the computer. Dust and stains on the connectors may cause memory access problems. 1.
PAGE 162
4 Replacement Procedures 4.6 Wireless LAN card Removing the Wireless LAN card To remove the wireless LAN card, make sure the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-9 to 4-10. NOTE: The wireless LAN card is an option. CAUTION: Do not try to remove the wireless LAN card with the computer turned on. The computer or the wireless LAN card can be damaged. Do not touch the connectors on the wireless LAN card module on the computer.
PAGE 163
4 Replacement Procedures 3. Disconnect the wireless LAN card from the connector on the main board. Be careful not to damage the connector.
PAGE 164
4 Replacement Procedures Installing the Wireless LAN card To install the wireless LAN card, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-9 to 4-10. CAUTION: Be sure to switch the computer off before installing the wireless LAN card. Otherwise, the computer or the wireless LAN card may be damaged. 1. Insert the wireless LAN card into connector at an angle on the main board. 2.
PAGE 165
4 Replacement Procedures 4.7 Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to Figures 4-11 to 4-14. 1. Remove the screws securing the bottom of the keyboard and the keyboard cover on the bottom case. M27L FLAT HEAD screw 1 M23L FLAT HEAD screw 2 M23L Figure 4-11 Removing the screws securing keyboard 2. Turn the computer over and open the display. 3. Remove the Keyboard cover.
PAGE 166
4 Replacement Procedures Figure 4-12 Removing the keyboard cover 4. Remove the following screws securing keyboard. M23L FLAT HEAD screw Figure 4-13 2 Removing the screws 5. Lift the keyboard upward a little and turn it face down on the palm rest. 6. Separate the keyboard flexible cable from connector and the keyboard LED cable from the connector on the main board then remove the keyboard.
PAGE 167
4 Replacement Procedures Installing the Keyboard To install the keyboard, follow the steps below and refer to Figures 4-11 to 4-14. 1. Place the keyboard face down on the top cover. 2. Connect the keyboard flexible cable to connector and the keyboard LED cable to the connector on the main board. 3. Turn the keyboard face up and set it in place. 4. Secure the keyboard with following two screws.  M23L FLAT HEAD screw 2 5.
PAGE 168
4 Replacement Procedures 4.8 Top cover Removing the Top cover To remove the Top cover, follow the steps below and refer to Figures 4-15 to 4-17. 1. Remove the following screws securing the bottom case to the toip case. M2.55L FLAT HEAD screw 6 M24L FLAT HEAD screw 6 M23L FLAT HEAD screw 3 M27L FLAT HEAD screw 3 M2X3L M2.5X5 M2X4 M2.5X5 M2X4 M2X7 Figure 4-15 Removing the screws on bottom case 2. Turn the bottom case face up and remove the following screws securing top cover.
PAGE 169
4 Replacement Procedures Figure 4-16 Removing the screws on top cover and separating the connector 4. Separate the Top cover from the bottom case. NOTE: remove the top cover according to the direction of the arrow.
PAGE 170
4 Replacement Procedures Installing the Top cover To install the top case, follow the steps below and refer to Figures 4-15 to 4-17. 1. Install the Top cover on the bottom case. 2. Secure the following screws on the Top cover.  M24L FLAT HEAD screw 5 3. Connect cable to connector on the main PCB, and turn the bottom case facedown. 4. Secure the following screws on the bottom case.  M2.
PAGE 171
4 Replacement Procedures 4.9 Bluetooth Removing the Bluetooth To remove the Bluetooth, follow the steps below and refer to Figures 4-18 to 4-19. 1. 2. 3. Remove two pieces of tape. Take the bluetooh away from the top cover. Remove the mylar on the fingerprint board. Mylar Tap Figure 4-18 4. Separate the cable from the connector according to the direction of the arrow.
PAGE 172
4 Replacement Procedures Installing the Bluetooth To install the Bluetooth, follow the steps below and refer to Figures 4-18 to 4-19. 1. Connect the cable to the Bluetooth. 2. Place the Bluetooth to the top cover. 3. Paste the tape and the mylar.
PAGE 173
4 Replacement Procedures 4.10 Power Button Board Removing the Power Button Board To remove the power button board, follow the steps below and refer to Figures 4-20 Remove the following two screws and remove the board.
PAGE 174
4 Replacement Procedures Installing the Power Button Board To install the power button board, follow the steps below and refer to Figures 4-20. 1. Install the Power Button board on the top cover. 2. Secure the following screws on the Top cover.
PAGE 175
4 Replacement Procedures 4.11 Fingerprint module Removing the fingerprint module To remove the fingerprint module, follow the steps below and refer to Figures 4-21 to 4-23. 1. Disconnect the cable. 2. Remove the following screws then remove the bracket. M23.5L FLAT HEAD screw 4 M23L FLAT HEAD screw 2 M2X3 Figure 4-21 3. Remove the following screws and then take the fingerprint and led board away M23.
PAGE 176
4 Replacement Procedures Figure 4-22 4.
PAGE 177
4 Replacement Procedures Installing the LED board To install the LED board, follow the steps below and refer to Figures 4-21 to 4-23. 1. Securing the board. 2. Install the LED board and the Fingerprint Board on the top cover. 3. Secure the following screws on the Top cover. M23.5L FLAT HEAD screw 4 4. Install the bracket then securing the following screws. M23.5L FLAT HEAD screw 4 M23L FLAT HEAD screw 2 5. Connect the cable to the board.
PAGE 178
4 Replacement Procedures 4.12 Touchpad on-off board Removing the touchpad on-off board To remove the touchpad on-off board follow the steps below and refer to Figures 4-24. 1. Remove screws securing the touchpad on-off board then remove the board M23L Figure 4-24 1 FLAT HEAD screw Removing screw securing touchpad on-off board Installing the Touchpad on-off board To install the touchpad on-off board, follow the steps below and refer to Figures 4-24. 1.
PAGE 179
4 Replacement Procedures 4.13 Main PCB Remove the main PCB To remove the main PCB, follow the steps below and refer to Figures 4-25 to 4-30. 1. Remove 7 pieces of tape and the LVDS screw. M2X2.5 FLAT HEAD screw 1 2. Remove cables on the main PCB.
PAGE 180
4 Replacement Procedures 3. Remove the following screws. M2X3 FLAT HEAD screw 4 M2X4 FLAT HEAD screw 6 M1.6 X2.5 FLAT HEAD screw 1 4. Remove the ODD bracket and battery bracket. M2X3L M1.6X2.5L Figure 4-27 Removing screws secure the main PCB 5. Remove the ODD module. Figure 4-28 Removing ODD 6. Remove the following screws and take the ODD bracket away.
PAGE 181
4 M22.5L FLAT HEAD screw Figure 4-29 Replacement Procedures 2 Removing ODD bracket 7. Lift the main PCB on the right side then remove it from the bottom case.
PAGE 182
4 Replacement Procedures Installing the main PCB To install the main PCB, follow the steps below and refer to Figures 4-25 to 4-30. 1. Securing the bracket to the ODD. M22.5L 2 FLAT HEAD screw 2. Place the Main PCB to the bottom case 3. Install the ODD to the Main PCB 4. Secure the main PCB to the bottom case using the following screws. M2X3 FLAT HEAD screw 4 M2X3 FLAT HEAD screw 6 M1.6 X2.5 FLAT HEAD screw 1 5. Connector the cable to the main PCB. 6. Securing the LVDS cable. M2X2.
PAGE 183
4 Replacement Procedures 4.14 LAN Board Remove the LAN board To remove the LAN Board, follow the steps below and refer to Figures 4-31. 1. Remove following screw securing the LAN board. M24L FLAT HEAD screw 1 2. Remove the LAN board. Figure 4-31 Removing screw securing LAN board Installing the main PCB To install the main PCB, follow the steps below and refer to Figures 4-31. 1. Install the LAN board. 2. Securing the LAN board with following screw.
PAGE 184
4 Replacement Procedures SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL] 4-45
PAGE 185
4 Replacement Procedures 4.15 D/C IN Cable Remove D/C in cable To remove the D/C in cable, follow the steps below and refer to Figures 4-32. 1. Remove the black mylar. 2. Remove following screw securing the bracket. M24L FLAT HEAD screw 1 3. Remove the bracket. Figure 4-32 Removing screw securing bracket 4. Remove the DC in cable.
PAGE 186
4 Replacement Procedures Installing the AC Power cable To install the D/C in cable, follow the steps below and refer to Figures 4-32 to 4-33. 1. Install the D/C in cable. 2. Install the bracket and securing the following screw. M24L FLAT HEAD screw 1 3. Paste the mylar.
PAGE 187
4 Replacement Procedures 4.16 Speaker Remove the speaker To remove the Speaker, follow the steps below and refer to Figures 4-57. 1. Remove the following screws securing the speaker. M22L Stand off screw 5 2. Remove the speaker from the bottom case.
PAGE 188
4 Replacement Procedures Installing the speaker To install the speaker, follow the steps below and refer to Figures 4-34. 1. Install the speaker. 2. Securing the following screw.
PAGE 189
4 Replacement Procedures 4.17 Remove LCD Module To remove the LCD module, follow the steps below and refer to Figures 4-35 to 4-36. 1. Remove 6 pcs of tapes Figure 4-35 Removing tapes 2. Remove the following three screws securing the hinge. M2.55L FLAT HEAD screw 4 3.
PAGE 190
4 Replacement Procedures Installing LCD Module To install the LCD module, follow the steps below and refer to Figures 4-35 to 4-36. 1. Install the LCD Module and securing the hinge with following screws. M2.55L FLAT HEAD screw 4 2. Arrange the cable. 3. Paste the tapes on the bottom case.
PAGE 191
4 Replacement Procedures 4.18 CPU Heat sink/CPU Removing the CPU Heat sink To remove the heat sink, follow the steps below and refer to Figures 4-37 to 4-38. CAUTION: 1) The CPU can become very hot during operation. Be sure to let it cool before starting repair work. 2) When you remove the CPU, replace the thermal pad on the bottom of heat sink with a new one before installing. 1. Turn the main PCB over and remove the following screws securing the CPU heat sink and remove it.
PAGE 192
4 Replacement Procedures 2. Unlock the CPU by turning the cam counterclockwise on the CPU socket 180 degrees using a flat-blade screwdriver. Figure 4-38 Unlocking the CPU 3. Remove the CPU. CAUTION: When removing the CPU, lift it straight up. Otherwise, pins on the CPU may be damaged.
PAGE 193
4 Replacement Procedures Install the CPU heat sink/CPU. To install the CPU heat sink/CPU, follow the steps below and refer to Figures 4-39 to 4-41. 1. Make sure the cam is in the open position. 2. Seat the CPU in the CPU socket. Make sure the direction and position of CPU is correct to avoid damaging pins on the CPU. CAUTION: Place the CPU as shown below. (Pay attention to the position of the triangle mark on the CPU.) 3.
PAGE 194
4 Replacement Procedures H000013080 H000013080 Figure 4-40 Applying new thermal pad 5. Install the CPU heat sink 6. Secure the CPU heat sink with the following screws in the numbered order as shown on the holder.
PAGE 195
4 Replacement Procedures 4.19 VGA Card Removing the VGA Card To remove the VGA card, follow the steps below and refer to Figures 4-42. 1. Remove the following screws securing the VGA. M23L FLAT HEAD screw 2 2. Remove the VGA Card from the slot at the pop-up angle Figure 4-42 Removing screws securing VGA Card Install the VGA Card. To install the VGA Card, follow the steps below and refer to Figures 4-42. 1. Insert the VGA Card into connector at an angle about 45 2.
PAGE 196
4 Replacement Procedures 4.20 FAN Removing the Fan To remove the Fan, follow the steps below and refer to Figures 4-43. 1. Remove the following three screws securing the fan. M24L FLAT HEAD screw 3 2. Disconnect the cable from the board. Figure 4-43 Removing screws securing FAN and disconnecting cable 3. Take the FAN away.
PAGE 197
4 Replacement Procedures Install the FAN. To install the FAN, follow the steps below and refer to Figures 4-43 to 4-44. 1. Apply new thermal pad on the fan as shown in the following figure. Stick the thermal pad on fan follow the mark. (Be sure to clean off all old pad before applying new thermal pad). H000013110 Figure 4-44 Apply new thermal pad on the fan 2. Install the Fan to the main board. 3. Secure the Fan with the following screws. M24L FLAT HEAD screw 3 4. Connect the cable.
PAGE 198
4 Replacement Procedures 4.21 LCD unit/Camera Removing the unit/Camera To remove LCD unit/Camera, follow the steps below and refer to Figures 4-45 to 4-50. 1. Remove the two tape and the following two screws securing the panel. M2.55L FLAT HEAD screw 2 2. Remove the panel according to the direction of the arrow Caution: Please be careful to not break LCD cover glass when LCD unit is disassembled and assembled.
PAGE 199
4 Replacement Procedures 3. Remove the tape and the screws securing LCD unit then remove the LCD unit M2.54L FLAT HEAD screw Figure 4-46 6 Removing the LCD unit NOTE: For environmental reasons, do not throw away a malfunctioning LCD unit (or FL). Please follow local ordinances or regulations for its disposal.
PAGE 200
4 Replacement Procedures 4. Remove the following screws securing the LCD supports and then remove them. M22.5L FLAT HEAD screw Figure 4-47 6 Removing the LCD supports 5. Remove one piece of glass tape on LCD cable connector.
PAGE 201
4 Replacement Procedures 6. Disconnect LCD cable from the connector and remove the cable. Glass tape Figure 4-48 Removing the LCD cable 7. Remove the Camera from the top case and disconnect the CCD cable from the camera.
PAGE 202
4 Replacement Procedures Installing the LCD unit / Camera To install the LCD unit / Camera, follow the steps below and refer to Figures 4-45 to 4-50. 1. Connect the CCD cable to the Camera. 2. Install the camera to the top case. 3. Connect the LCD cable to the LCD unit 4. Secure one piece of glass tape on LCD cable connector. 5. Seat two LCD supports on the LCD and secure them with the following screws.  M22.
PAGE 203
Appendix A Handling the LCD Module Appendix A Appendices P Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
PAGE 204
Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. 4.
PAGE 205
Appendix A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.
PAGE 206
Appendices Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
PAGE 207
Appendix A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.
PAGE 208
Appendix B Board Layout Appendices Appendix B Board Layout B.
PAGE 209
Appendices Appendix B Board Layout Table B-1 Main board connectors (front) Number CON6202 Camera / Int.
PAGE 210
Appendix B Board Layout B.
PAGE 211
Appendices Appendix B Board Layout Table B-2 Main board connectors (back) Number Name CBT_CON1 (HOT BAR) B-4 FUNCTION BRD connector CON3801 RGB connector CON4901 FAN connector CON7701 Battery Connector CON6502 DEBUG CARD connector CON6001 HDD connector CON6002 ODD connector CON6003 SSD connector CON2101 Memory slot CON2201 Memory slot CON5501 Mini card connector CON0701 AMD HDT Debug connector CON3501 Graphics MXM connector CON5701 Mini card connector CON5001 Media Card slo
PAGE 212
Appendix B Board Layout B.
PAGE 213
Appendices B.
PAGE 214
Appendix B Board Layout B.
PAGE 215
Appendices B.
PAGE 216
Appendix B Board Layout B.
PAGE 217
Appendix C Pin Assignments Appendices Appendix C Pin Assignments Main board C.1 CON2101 SO-DIMM0 connector (200-pin) Table Pin No. C-1 Signal Name SO-DIMM0 connector (200-pin) (1/3) I/O Pin No.
PAGE 218
Appendices Appendix C Table Pin No. C-2 C-1 Signal Name Pin Assignments SO-DIMM0 connector (200-pin) (2/3) I/O Pin No. Signal Name I/O I/O 64 M_A_DQ34 - 66 GND I/O 68 M_A_DQS#4 I/O I/O 63 M_A_DQ32 I/O 65 GND 67 M_A_DM4 69 NC - 70 M_A_DQ4 71 GND - 72 GND 73 M_A_DQ33 I/O 74 M_A_DQ37 I/O 75 M_A_DQ36 I/O 76 M_A_DQ35 I/O 77 GND - 78 GND - 79 M_CKE0 I 80 M_CKE1 I 81 +1.8V - 82 +1.8V - 83 NC - 84 NC - 85 M_A_BS2 I 86 M_A_A14 - 87 +1.
PAGE 219
Appendix C Pin Assignments Table Pin No. C-1 Signal Name Appendices SO-DIMM0 connector (200-pin) (3/3) I/O Pin No.
PAGE 220
Appendices C.2 Appendix C CON2201 SO-DIMM1 connector (200-pin) Table Pin No. C-4 Pin Assignments C-2 Signal Name SO-DIMM1 connector (200-pin) (1/3) I/O Pin No.
PAGE 221
Appendix C Pin Assignments Table Pin No. C-2 Signal Name Appendices SO-DIMM1 connector (200-pin) (2/3) I/O Pin No. Signal Name I/O I/O 64 M_B_DQ32 - 66 GND I/O 68 M_B_DQS#4 I/O I/O 63 M_B_DQ38 65 GND 67 M_B_DM4 69 NC - 70 M_B_DQS4 71 GND - 72 GND 73 M_B_DQ34 I/O 74 M_B_DQ37 I/O 75 M_B_DQ39 I/O 76 M_B_DQ33 I/O 77 GND - 78 GND - 79 M_CKE2 I 80 M_CKE3 I 81 +1.8V - 82 +1.8V - 83 NC - 84 NC - 85 M_B_BS2 I 86 M_B_A14 - 87 +1.
PAGE 222
Appendices Appendix C Table Pin No. C-6 C-2 Signal Name Pin Assignments SO-DIMM1 connector (200-pin) (3/3) I/O Pin No.
PAGE 223
Appendix C Pin Assignments C.3 CON6002 Appendices SATA interface ODD connector (13-pin) Table C-3 ODD connector (13-pin) Pin No. C.4 Signal Name I/O Pin No. Signal Name I/O S1 GND - S2 SATA_TXP2 I S3 SATA_TXN2 I S4 GND - S5 SATA_RXN2 O S6 SATA_RXP2 O S7 GND - P1 NC - P2 +5VS - P3 +5VS - P4 NC - P5 GND - P6 GND - CON6001 SATA interface HDD connector (22-pin) Table C-4 HDD connector (22-pin) Pin No. Signal Name I/O Pin No.
PAGE 224
Appendices C.5 Appendix C CON6003 SATA interface SSD connector (BTO) (24-pin) Table Pin No. C-8 Pin Assignments Signal Name C-5 SSD connector (24-pin) I/O Pin No.
PAGE 225
Appendix C Pin Assignments C.6 CON5001 Media card connector (45-pin) Table Pin No. Appendices Signal Name C-6 Media card connector (45-pin) I/O Pin No.
PAGE 226
Appendices C.7 Appendix C CON4201 H/P interface connector (8-pin) Table Pin No. C.8 C-7 Signal Name H/P interface connector (8-pin) I/O Pin No. Signal Name I/O 1 JACK1_D# I 2 HP_JACK_R O 3 HP_JACK_L O 4 GND - 5 JACK2_D# I JACK_IN I A GND - VCC_SPDIF - C SPDIF_OUT O B CON5701 WLAN Mini Card interface connector (52-pin) Table Pin No.
PAGE 227
Appendix C Pin Assignments C.9 Appendices CON5501 Upconvert Mini Card interface connector(BTO) (52-pin) Table Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 C-9 Signal Name NC NC NC MINI1CLK_REQ# GND CLK_PCIE_MINI CARD# CLK_PCIE_MINI CARD GND NC NC GND PCIE_RXN2 PCIE_RXP2 GND GND PCIE_TXN2 PCIE_TXP2 GND GND +3VS +3VS GND NC NC NC NC Mini Card interface connector (52-pin) I/O O I Pin No. 2 4 6 8 10 12 I 14 Signal Name +3VS GND +1.
PAGE 228
Appendices Appendix C Pin Assignments C.10 CON5601 WWAN Mini Card interface connector(BTO) (52-pin) Table Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 C-12 C-10 Mini Card interface connector (52-pin) Signal Name NC NC NC NC GND CLK_PCIE_WWAN# CLK_PCIE_WWAN GND NC NC GND PCIE_RXN3 PCIE_RXP3 GND GND PCIE_TXN3 PCIE_TXP3 GND GND +3VS_WWAN +3VS_WWAN GND NC NC NC NC I/O O I I O O I I - Pin No.
PAGE 229
Appendix C Pin Assignments C.11 CON5602 SIM Card connector(BTO) (12-pin) Table Pin No. Appendices C-11 MDC interface connector (12-pin) Signal Name I/O Pin No. Signal Name I/O C1 SIM_VCC_C - C2 SIM_RST I C3 SIM_CLK I C5 GND - C6 NC - C7 SIM_DIO C.12 CON6501 MDC interface connector(BTO) (12-pin) Table Pin No. I/O C-12 MDC interface connector (12-pin) Signal Name I/O Pin No.
PAGE 230
Appendices Appendix C C.14 CON4801 Keyboard interface connector (34-pin) Table Pin No. C-14 Keyboard interface connector Signal Name I/O Pin No.
PAGE 231
Appendix C Pin Assignments C.16 CON4804 Touch PAD ON/OFF connector (4-pin) Table Pin No. Appendices C-16 Signal Name Touch PAD Button connector (4-pin) I/O Pin No. Signal Name I/O 1 +5VS - 2 NC - 3 TP_ON O 4 GND - C.17 CON4202 Microphone In connector (8-pin) Table Pin No. C-17 Signal Name Microphone In connector (8-pin) I/O Pin No. Signal Name I/O 1 A_GND - 2 MIC_IN_AC_E I 3 NC - 4 MIC_EXT_JD# - 5 A_GND 7 A_GND A_GND - C.
PAGE 232
Appendices Appendix C C.20 CON6701 MB to LAN Board connector (34-pin) Table Pin No. C-20 MB to LAN Board connector (34-pin) Signal Name I/O Pin No.
PAGE 233
Appendix C Pin Assignments C.23 CON6107 eSATA/USB Combo connector (11-pin) Table Pin No. Appendices Signal Name C-23 Speaker connector (11-pin) I/O Pin No. Signal Name I/O - 2 USBP7-_C I/O 4 GND - 1 +5VUSB7 3 USBP7+_C 5 GND - 6 SATA_TXP3_C I 7 SATA_TXN3_C I 8 GND - 9 SATA_RXN3_C O 10 SATA_RXP3_C O 11 GND - C.24 CON3701 LCD connector (40-pin) Table Pin No. I/O Signal Name C-24 LCD connector (40-pin) I/O Pin No.
PAGE 234
Appendices Appendix C C.25 CON3801 RGB connector (15-pin) Table Pin No. 1 Signal Name RED C-25 RGB connector (15-pin) I/O I Pin No. 2 Signal Name GREEN I/O I 3 BLUE I 4 NC - 5 GND: - 6 GND - 7 GND - 8 GND - 9 +5VS - 10 GND - 11 NC - 12 DDC2BD_S 13 HSYNC I 14 VSYNC 15 DDC2BC_S I C.26 CON5401 Pin No. 1 I/O I Newcard interface connector (26-pin) Table C-26 Newcard interface connector (26-pin) Signal Name GND I/O - Pin No.
PAGE 235
Appendix C Pin Assignments C.27 J7701 DC-IN connector (4-pin) Table Pin No. Appendices C-27 Signal Name DC-IN connector (4-pin) I/O Pin No. Signal Name I/O 1 GND - 2 GND - 3 D_A/D_DOCK_IN - 4 D_A/D_DOCK_IN - C.28 CON7701 Battery connector (9-pin) Table Pin No. C-28 Signal Name Battery connector (9-pin) I/O Pin No. Signal Name - 2 BAT_CON_F - 4 GND - 1 BAT_CON_F 3 NC 5 TS1#_C O 6 SMB0_DAT_C 7 SMB0_CLK_C I 8 GND 9 GND - C.
PAGE 236
Appendices Appendix C C.31 CON6201 Touch Panel connector (BTO) (6-pin) Table Pin No. C-31 Signal Name I/O Pin No. Signal Name LID_SW# I 2 GND 3 USBP8+ I/O 4 USBP8- 5 TPN_RST# I 6 +3VS_TPN Pin No. C-32 Signal Name 1 +5VS_FELICA 3 USBP11+ 5 NC C.33 CO6204 I/O - Felica Module connector (6-pin) I/O Pin No. Signal Name I/O - 2 USBP11- I/O 4 GND - - 6 GND - I/O Buletooth connector (BTO) (8-pin) Table Pin No.
PAGE 237
Appendix C Pin Assignments Appendices Touch PAD Board C.34 M1TP_CON1 (12-pin) Table Pin No. C-34 Touch PAD board to Touch PAD connector Touch PAD Board to Touch PAD connector (12-pin) Signal Name I/O Pin No. Signal Name I/O - 2 +5VS - I/O 4 TP_CLK I 1 +5VS 3 TP_DAT 5 GND - 6 GND - 7 NC - 8 LightGuide_ON_ OFF - 9 NC - 10 TP_LEFT# O 11 TP_RIGHT# O 12 NC - C.35 M1TP_J1 (6-pin) Table Pin No.
PAGE 238
Appendices Appendix C Pin Assignments LAN Board C.36 MLCON301 LAN/RJ11(BTO) interface connector (14-pin) Table Pin No. C-36 LAN/RJ11 interface connector (14-pin) Signal Name Pin No. Signal Name I/O 1 L_TXP_M I/O 2 L_TXN_M I/O 3 L_RXP_M I/O 4 L_TRLP2_M I/O 5 L_TRLM2_M I/O 6 L_RXN_M I/O 7 L_TRLP3_M I/O 8 L_TRLM3_M I/O 9 +3VSUS_L_M - 10 LED_1000#_M I 11 +3VSUS_L_M - 12 LED_100#_M I 13 RING_J_M I/O 10 TIP_J_M C.37 MLCON103 Pin No.
PAGE 239
Appendix D Keyboard Scan/Character Codes Appendices Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Cap No.
PAGE 240
Appendices Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (2/4) D-2 Cap No.
PAGE 241
Appendix D Keyboard Scan/Character Codes Appendices Table D-1 Scan codes (set 1 and set 2) (3/4) Cap No.
PAGE 242
Appendices Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (4/4) Cap No. Keytop Code set 1 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc Refer to table 2-25 126 Pause Refer to table 2-25 202 Fn 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0 2F E0 F0 2F Make Code set 2 Break Make Note Break *5 Notes: 1. 2. 3. 4. 5. D-4 * * * * * Scan codes differ by overlay function.
PAGE 243
Appendix D Keyboard Scan/Character Codes Appendices Table D-2 Scan codes with left Shift key Cap Key No.
PAGE 244
Appendices Appendix D Keyboard Scan/Character Codes Table D-3 Scan codes in Numlock mode Cap Key Code set 1 No.
PAGE 245
Appendix D Keyboard Scan/Character Codes Appendices Table D-5 Scan codes in overlay mode Cap No.
PAGE 246
Appendices Appendix D Keyboard Scan/Character Codes Table D-7 No.126 key scan code Key top Shift Code set 1 Code set 2 Make Make Pause Common * E1 1D 45 E1 Ctrl* E0 46 E0 C6 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
PAGE 247
Appendix E Key Layout Appendices Appendix E Appendix E E.1 Key Layout United Kingdom (UK) Keyboard Figure E-1 UK keyboard E.
PAGE 248
Appendices E.
PAGE 249
Appendix F BIOS rewrite procedures Appendices Appendix G Appendix F BIOS rewrite procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  Bootable USB key for the computer that has renewed BIOS data. Rewriting the BIOS 1. Set the system to boot mode. 2. Turn off the power to the computer. 3.
PAGE 250
Appendix G EC/KBC rewrite procedures Appendices Appendix H Appendix G EC/KBC rewrite procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool:  Bootable USB key for the computer that has renewed BIOS data. Rewriting the EC/KBC NOTE: 1. Rewrite the EC/KBC only when instructed by a diagnostic disk release notice. 2. Connect the AC adaptor to the computer when you rewrite the EC/KBC. 3.