Toshiba Personal Computer Satellite & Satellite Pro Maintenance Manual TOSHIBA CORPORATION
Copyright © 2010 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Personal Computer Satellite Maintenance Manual First edition April.2010 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite, referred to as the Satellite Series in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention.
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third.
Table of Contents Chapter 1 Hardware Overview 1.1 Features ...............................................................................................................................1-1 1.2 2.5-inch HDD ......................................................................................................................1-9 1.3 DVD Super Multi (+-R Double Layer) .............................................................................1-10 1.4 Power Supply ....................................
2-17 BUTTON troubleshooting process....................................................................................... 41 2.18 Modem troubleshooting process .......................................................................................... 44 2.19 Express card troubleshooting process .................................................................................. 46 2.20 HDMI troubleshooting process ........................................................................................
Chapter 4 4.1 Replacement Procedures General ............................................................................................................................. 4-1 Safety Precautions ............................................................................................................ 4-3 Before You Begin............................................................................................................. 4-5 Disassembly Procedures ..................................................
Disassembling the ODD Drive ....................................................................................... 4-24 Assembling the ODD Drive ........................................................................................... 4-25 4.8 Logic Upper Assembly .................................................................................................. 4-26 Removing the Logic Upper Assembly ...........................................................................
Installing the Bluetooth .................................................................................................. 4-41 4.17 Thermal Fan ................................................................................................................... 4-42 Removing the Thermal Fan ............................................................................................ 4-42 Installing the Thermal Fan .............................................................................................
Installing the WLAN Antennas ...................................................................................... 4-63 4.27 LCD Panel Hinges ......................................................................................................... 4-64 Removing the LCD Panel Hinges .................................................................................. 4-64 Installing the LCD Panel Hinges .................................................................................... 4-64 4.
Figure 4.22 Removing the FeliCa card from the logic upper assembly............................... 4-32 Figure 4.23 Raising the fingerprint scanner bracket from the logic upper assembly........... 4-33 Figure 4.24 Working the fingerprint scanner bracket loose................................................. 4-34 Figure 4.25 Removing the fingerprint scanner bracket from the logic upper assembly ...... 4-34 Figure 4.26 Removing the touch pad board ...............................................................
Figure 4.52 Removing the LCD panel hinges from the LCD Panel .................................... 4-64 Figure 4.53 Removing the LVDS cable from the LCD panel .............................................. 4-65 Appendices Appendix A Handling the LCD Module ................................................................................... A-1 Appendix B Board Layout ......................................................................................................... B-1 Appendix C Pin Assignments..
1 Hardware Overview Chapter 1 Hardware Overview Satellite A660/Pro A660 Maintenance Manual 1-i
1 Hardware Overview Chapter 1 Contents 1.1 Features .................................................................................................................. 1-1 1.2 2.5-inch HDD ....................................................................................................... 1-11 1.3 DVD Super Multi (+-R Double Layer) ................................................................ 1-12 1.4 BD-RE and BD-Combo drives ..................................................................
1 Hardware Overview Figures Figure 1-1A ID Parts Description Placement Part A .......................................................... 1-6 Figure 1-2 SATA HDD ................................................................................................. 1-11 Figure 1-3 DVD Super Multi Drive............................................................................... 1-12 Figure 1-4 BD-RE or BD-Combo drive (depending on the model) ..............................
1 Hardware Overview 1.1 Features The Toshiba Satellite A660/A665/A667 Series and Dynabook TX/AX Series is a full-size PC notebook based on a Dual Core/Quad Core Processor, providing high-speed processing capabilities and advanced features. The computer employs a lithium ion battery that allows it to operate without a DC-in connection for extended periods of time. The display uses a 15.6” or 16” TFT LCD panel.
1 Hardware Overview 12.7mm height BD-Combo drive (supporting BD/DVD/CD/ DVD-R / -RW / +R / +RW / -RAM / -RDL / +RDL / CD-R / CD-RW) 12.7mm height BD-RE drive (supporting BD/DVD/CD/BD-R/BD-RE/ DVD-R / -RW / +R / +RW / -RAM / -RDL / +RDL / CD-R / CD-RW) Display (BTO) The computer display features one of the following LCD panels: 16"W 1366 x 768: color TFT/HD 15.6"W 1366 x 768: color TFT/HD Graphics (BTO) Intel Arrandale for int.
1 Hardware Overview Universal Serial Bus (USB) Ports The computer has three USB 2.0 ports. It is supported to daisy-chain a maximum of 127 USB devices. The serial data transfer rate is 480 Mbps or 12 Mbps and 1.5 Mbps. These ports support PnP installation and hot plugging. They also support Sleep and Charge function.
1 Hardware Overview Headphones-Out Jack This jack enables connection of stereo headphones (16 ohm minimum). When connected to headphones, the internal speakers are automatically disabled. Microphone/ Line-in Jack A 3.5mm mini microphone jack enables connection of a three-conductor microphone for monaural input and also enables the connection of a stereo device for audio input.
1 Hardware Overview Bluetooth (BTO) Some computers in this series offer Bluetooth wireless communication functionality which eliminates the need for cables between electronic devices such as computers and printers. When implemented, Bluetooth provides a fast, reliable and secure means to achieve wireless communication in a small space. This module is Version 2.1 + EDR and is V3.0+HS support ready.
1 Hardware Overview Figure 1-1A shows the computer and its system unit configuration.
1 Hardware Overview Satellite A660/Pro A660 Maintenance Manual 1-7
1 Hardware Overview Satellite A660/Pro A660 Maintenance Manual 1-8
1 Hardware Overview The system unit of the computer consists of the following components: Processor (BTO) The computer is equipped with one of the following Intel® processors: Intel® Clarksfield Processor Intel® Arrandale Processor Memory (BTO) The computer has two SODIMM slots that come standard with 1GB/2GB/4GB, BTO for various memory requirements. It can incorporate up to 8 GB of main memory. It supports DDR3 at 1066MHZ and 1333MHZ depending on the model.
1 Hardware Overview Graphics Controller Intel® HM55 as integrated graphics solution Following External Graphic solution with Intel PM55/HM55 NVIDIA® GeForce® N11M-GE1/N11P-GE1/N11E-GE1-LP, N11M-OP1 HDMI 1.3-CEC support Express Card Controller Support USB/PCI Express signals One Express Card slot 34 Audio Controller Realtek Azalia ALC269 One Audio-in port: Mic.
1 Hardware Overview 1.2 2.5-inch HDD The computer contains an extremely low-profile and lightweight, high-performance HDD. The HDD incorporates 9.5 mm / 12.5 mm height magnetic disk and mini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 160, 250, 320, 400, 500 and 640GB. The HDD is shown in Figure 1-2 and some of its specifications are listed in Table 1-1.
1 Hardware Overview 1.3 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed, CD-RW at 6x speed, CD-RW at 16x speed, DVD-R at 8x speed, DVD-RW at 8x speed, DVD+R at 8x speed, DVD+R (Double Layer) at 8x speed, DVD-R (Dual Layer) at 8x speed, DVD+RW at 8x speed and DVD-RAM at 5x speed.
1 Hardware Overview 1.4 BD-RE and BD-Combo drives The BD-RE and BD-Combo drives accept 12-cm (4.72-inch) and 8-cm (3.15-inch) discs and can play BDs, DVDs and CDs. At maximum the drives can playback BD at 6x speed, DVD at 8x speed, read CD-ROM at 24x speed The BD-RE and BD-Combo drives let you record data to writable CD/DVD discs.
1 Hardware Overview 1.5 Power Supply The power supply unit provides constant voltage (19V) for the system board and performs the following functions: 1. Power input monitor Checks whether the AC adapter (DC power supply) is connected to the computer. Checks whether the battery pack is connected to the computer. Monitors the DC power supply input voltage (AC Adapter output voltage). 2. Power supply's internal control Turns on and off the battery pack charging power supply.
1 Hardware Overview 6. Output monitor Monitors the voltage output to the system block (load/logic circuit side). Monitors the voltage, over-voltage, input/output current of the battery pack. Monitors the internal temperature of the battery pack. Monitors the supply voltage from the AC adapter.
1 Hardware Overview 1.6 Batteries The computer has the following two types of batteries: Main Battery Pack Real Time Clock (RTC) Battery 1.6.1 Main Battery The main battery pack serves as the computer's main power source when the AC adapter is not attached. The main battery maintains the state of the computer when the AC adapter is detached. 1.6.2 Battery Charging Control Battery charging is controlled by EC KB926.
1 Hardware Overview NOTE: The time required for normal charge depends on the power consumption by the system. Using a fluorescent lamp and frequently accessing the disk consumes more power and lengthens the charge time. Any of the following can stop battery charge: 1. The battery becomes fully charged. 2. The AC adapter or battery pack is removed. 3. The battery or AC adapter voltage is abnormal.
Chapter 2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting Introduction ...................................................................................... 4 2.2 Troubleshooting Flowchart ……………………………………………………………5 2.3 Power Supply Troubleshooting ……………………………………………………...11 2.4 Display Troubleshooting..............................................................................................16 2.5 Keyboard Troubleshooting ........................................................
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (2/1) ………………………………………………6 Figure 2-1 Troubleshooting flowchart (2/2) ………………………………………………7 Figure2-2 Power Supply Troubleshooting Process ……………………………………..11 Figure 2-3 Display troubleshooting process ……………………………………………..16 Figure 2-4 Keyboard troubleshooting process .................................................................. 19 Figure 2-5 External USB device troubleshooting process .....................................
2 Troubleshooting Procedures Tables Table 2-1 Battery LED ......................................................................................................121 Table 2-2 DC-IN LED .......................................................................................................
2 Troubleshooting Procedures 2.1 Troubleshooting Introduction Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Display 7. Optical driver 13. HDMI CEC 4. TV-Tuner&B-Cas 25. LAN 2. Keyboard 8. Modem 20. Sleep & Charge 26. Light sensor 3. USB ports 9. Express card 4. MIC 19. 3D Sensor 15. Finger printer 21. Bridge Media slot 10.Wireless LAN 16. E-SATA 22. Sleep & Play music 28. CIR 5.
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart If you know the location of the malfunction, turn directly to the appropriate section of this chapter. If the problem is unspecified, use the flowchart in Figure 2-1 as a guide for determining which troubleshooting procedures to execute. Before performing any troubleshooting procedures, verify the following: Ask the user if a password is registered, if it is, ask him or her to enter the password.
2 Troubleshooting Procedures START C o n n e c t th e A C a d a p te r to th e D C IN s o c k e t Is th e D C -IN L E D o n ? No P e rfo rm th e P o w e r S u p p ly T ro u b le sh o o tin g p ro c e d u re s in s e c tio n 2 .3 No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .3 No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .
2 Troubleshooting Procedures A Does typed characters appear correctly? No Perform the Keyboard Troubleshooting procedures in section 2.6 No Perform the USB memory disk or CD ROM Troubleshooting procedures in section 2.5 Yes After confirming which diagnostics test has detected an error, perform the appropriate procedure as outlined below. Yes Insert USB memory disk or CD ROM, Then run the diagnostics test program.
2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The test program should be executed several times to isolate the problem. When a problem has been located, perform the appropriate troubleshooting procedures as follows: 1. If an error is detected by the battery test, perform the Power Supply Troubleshooting procedures in Section 2.3 2. If an error is detected by the display test, perform the Display Troubleshooting procedures in Section 2.4 3.
2 Troubleshooting Procedures Other problems that are not covered by the diagnostics program may be discovered by a user. 1. If an error is detected when using an external USB device, perform the External USB Devices Troubleshooting procedures in Section 2.6 2. If an error is detected when using the TV-out connection, perform the TV-Out Failure Troubleshooting procedures in Section 2.7 3. If an error is detected when using the modem, perform the Modem Troubleshooting procedures in Section 2.11 4.
2 Troubleshooting Procedures 17. If an error is detected when using the CIR, perform the CIR troubleshooting procedures in Section 2.27 18. If an error is detected when using the Sleep & Play music, perform the Sleep & Play music troubleshooting procedures in Section 2.28 19. If an error is detected when using the Wimax, perform the Wimax troubleshooting procedures in Section 2.29 20. If an error is detected when using the 3G, perform the 3G troubleshooting procedures in Section 2.30 21.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures Figure 2-2 Power Supply Troubleshooting Process The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The flowchart in Figure 2-2 gives a summary of the process.
2 Troubleshooting Procedures Amber color off SatelliteA660/ProA660 Series Maintenance Manual 13 Battery not in low or critical low state; It’s in discharging state
2 Troubleshooting Procedures Table 2-2 DC-IN LED AC-IN LED Power supply status Solid on AC power exists (LED is solid White). Off No AC power exists. To check the power supply status, install a battery pack and connect an AC adaptor to the DC-IN port on the computer and to a power supply. If the DC-IN LED or Battery LED is not lit, go to Procedure 2. Procedure 2 Adaptor / battery replacement A faulty adaptor may not supply power or may not charge the battery. Perform Check 1.
2 Troubleshooting Procedures Procedure 3 Power supply connection check The power supply wiring diagram is shown below: AC adaptor cord AC power cord AC adaptor System board Battery Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord. If there is no damage, go to Check 2.
2 Troubleshooting Procedures Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5. 3. Run the Diagnostic test following the procedures described in Chapter 3, Tests and Diagnostics. If no problem is detected, the battery is functioning normally.
2 Troubleshooting Procedures 2.4 Display Troubleshooting START P e rf o r m e x te r n a l d is p la y c h e c k (P ro c e d u r e 1 ) D o e s th e e x te rn a l d is p la y f u n c tio n o k ? No P e rf o r m d ia g n o s tic c h e c k ( P r o c e d u re 2 ) Y es W a s a d is p la y p ro b le m d e te c te d ? No D is p la y is n o t fa u lty .
2 Troubleshooting Procedures This section describes how to determine if the computer’s display is functioning properly. The process is outlined in Figure 2-3. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External display check Procedure 2: Diagnostic check Procedure 3: Connector and replacement check Procedure 1 External display check Connect an external display to the computer’s external monitor port, and then boot the computer.
2 Troubleshooting Procedures Procedure 3 Connector and replacement check The LCD module and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Make sure the DDR RAM module is seated properly. Test display again. If the problem still exits, replace the DDR RAM module. If the problem still exists, perform Check 2.
2 Troubleshooting Procedures 2.5 Keyboard Troubleshooting STA RT P e rfo rm d ia g n o s tic c h e c k (P ro c e d u re 1 ) W as a k ey b o ard p ro b le m d e te c te d ? No K e y b o a rd is n o t fa u lty .
2 Troubleshooting Procedures To determine if the computer’s keyboard is functioning properly, perform the following procedures. Figure 2-4 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic check Procedure 2: Connector and replacement check Procedure 1 Diagnostic check Run the test and Diagnostics Program, which will automatically execute the Keyboard Test.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures To determine if the computer’s external USB devices are functioning properly, perform the following procedures. Figure 2-5 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: External device and connection check Procedure 2: Replace system board Procedure 1 External device and connection check The USB device may be damaged or the connection may be faulty. Use windows application to check device can work fine or not.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures To determine if the computer’s TV Tuner port is functioning properly, perform the following procedures. Figure 2-6 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: TV Tuner cable connection check Procedure 2: TV Tuner Antenna connection check Procedure 3: TV Tuner Module connection check Procedure 1 TV tuner Cable connection check The TV Tuner cable may be damaged or the connections may be loose.
2 Troubleshooting Procedures 2.8 Touch Pad Troubleshooting ST A R T P erfo rm T o u ch p ad check (P ro ce d u re 1 ) D oes T ouchpad f u n c tio n o k ? No P e rfo rm d ia g n o stic check (P ro c ed u re 2 ) Y es W as a T ouchpad p ro b le m d e te c te d ? No T o u c h p a d is n o t fa u lty .
2 Troubleshooting Procedures To determine if the computer’s built-in Touchpad is functioning properly, perform the following procedures. Figure 2-7 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Diagnostic test Procedure 2: Touchpad connection check Procedure 3: Touchpad replacement check Procedure 1 Diagnostic test Run the Diagnostic Program, which will automatically execute the Touchpad test.
2 Troubleshooting Procedures 2.9 Speaker Troubleshooting STA RT P e r f o r m a u d io s o u r c e t e s t (P ro c e d u re 1 ) D o a ll s o u r c e s h a v e s a m e p r o b le m ? No S p e a k e rs a re n o t f a u l ty .
2 Troubleshooting Procedures To determine if the computer’s built-in speakers are functioning properly, perform the following procedures. Figure 2-8 outlines the process. First adjust the speaker volume to an appropriate level. Start with Procedure 1 and continue as instructed. Procedure 1: Audio source test Procedure 2: Earphone test Procedure 3: Connection check Procedure 4: Replacement check Procedure 1 Audio source test Try different audio sources (e.g.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures Figure 2-9 Optical drive troubleshooting process This section describes how to determine if the computer’s internal optical drive is functioning properly. The Satellite/Satellite Pro A660/A665/A667 Series/Dynabook TX/AX Series Maintenance Manual module bays can accommodate the following optical drives: DVD SuperMulti supporting +-R Double Rayer Blue-Ray ODD supporting Figure 2-9 outlines the process.
2 Troubleshooting Procedures Procedure 4 Connection check and replacement check The optical drive connects to the system board. The drive may be disconnected, or the drive or system board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the drive is firmly connected to the system board. If the connection is good and there is still an error, go to Check 2.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Figure 2-10 Modem troubleshooting process SatelliteA660/ProA660 Series Maintenance Manual 34
2Troubleshooting Procedures This section describes how to determine if the computer's modem is functioning properly. Figure 2-10 outlines the process. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Telephone line connection check Procedure 2: Modem card connection check Procedure 3: Modem card replacement check Procedure 1 Telephone line connection check The telephone cable may be damaged or the connections may be loose.
2Troubleshooting Procedures 2.12 Express card Troubleshooting START P e rf o rm E x p re s s c a rd te s t ( P ro c e d u re 1 ) D o e rro r s o c c u r d u rin g E x p r e s s c a rd te s t? Y es P e rfo rm E x p re s s c a rd s o c k e t re p la c e m e n t c h e c k ( P ro c e d u re 2 ) R e p la c e s y s te m b o a r d END SatelliteA660/ProA660 Series Maintenance Manual 36 No E x p re s s c a rd u n it is n o t fa u lty .
2Troubleshooting Procedures Figure 2-11 Express card troubleshooting process SatelliteA660/ProA660 Series Maintenance Manual 37
2Troubleshooting Procedures This section describes how to determine if the Express card player is functioning properly. The process is summarized in Figure 2-11. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Express card test Procedure 2: Express card socket replacement check Procedure 1 Express card test The Express test card contains an Express test program. Use windows application to check device can work fine or not.
2Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting START Perform Wireless LAN connection check (Procedure 1) Was a wireless LAN problem delected? Yes Perform connector and replacement check (Procedure 2) Replace wireless LAN antenna/unit Replace system board END SatelliteA660/ProA660 Series Maintenance Manual 39 No Wireless LAN system is not faulty.
2Troubleshooting Procedures Figure 2-12 Wireless LAN troubleshooting process Notes: W/L Antenna assemble rule as below: Color of antenna Assemble location White antenna Main/1 Black antenna Aux/2 The wireless LAN antenna wire, wireless LAN unit or system board may each be the source of a wireless LAN fault. Any of these components may be damaged. To determine if the computer’s wireless LAN system is functioning properly, perform the following procedures. Figure 2-12 outlines the process.
2Troubleshooting Procedures Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Figure 2-13 Camera troubleshooting process The Camera board or system board may be the reason of a Camera fault. Either of these two components may be damaged. To determine if the computer’s Camera is functioning properly, perform the following procedures. Figure 2-13 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Figure 2-14 Bluetooth troubleshooting process The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be damaged. To determine if the computer’s Bluetooth is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures SatelliteA660/ProA660 Series Maintenance Manual 46
2Troubleshooting Procedures 2.16 Bridge Media Slot Troubleshooting START Perform Bridge Media Slot test (Procedure 1) Do errors occur during Bridge Media Slot test? Yes Bridge Media Slot socket replacement check (Procedure 2) Replace system board END Figure 2-15 5 in 1 card troubleshooting process SatelliteA660/ProA660 Series Maintenance Manual 47 No Bridge Media Slot unit is not faulty.
2Troubleshooting Procedures This section describes how to determine if the Bridge Media Slot player is functioning properly. The process is summarized in Figure 2-15. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Bridge Media Slot test Procedure 2: Bridge Media Slot replacement check Procedure 1 Bridge Media Slot test The Bridge Media Slot test PLS Use windows application to check device can work fine or not.
2Troubleshooting Procedures SatelliteA660/ProA660 Series Maintenance Manual 49
2Troubleshooting Procedures 2.
2Troubleshooting Procedures The HDD/SSD or system board may be the reason of a HDD/SSD fault. Either of these two components may be damaged. To determine if the computer’s HDD/SDD is functioning properly, perform the following procedures. Figure 2-16 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures To determine if the computer’s CRT port is functioning properly, perform the following procedures. Figure 2-17 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: CRT connection check Procedure 2: CRT set check Procedure 1 CRT connection check The CRT cable may be damaged or the connections may be loose. Use windows application to check device can work fine or not.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures To determine if the computer’s HDMI port is functioning properly, perform the following procedures. Figure 2-18 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: HDMI connection check Procedure 2: HDMI set check Procedure 1 HDMI CEC connection check The HDMI cable may be damaged or the connections may be loose. Use windows application to check device can work fine or not.
2Troubleshooting Procedures 2.20 MIC Troubleshooting Figure 2-19.
2Troubleshooting Procedures The MIC line or system board may be the reason of a MIC fault. Either of these two components may be damaged. To determine if the computer’s MIC is functioning properly, perform the following procedures. Figure 2-19 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Windows Application test Procedure 2: Connector and replacement check Procedure 1 Windows Application test Run the functioning Program (record.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures The Finger printer board or system board may be the reason of a finger printer fault. Either of these two components may be damaged. To determine if the computer’s Finger printer is functioning properly, perform the following procedures. Figure 2-20 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures 2.22 E-SATA Troubleshooting START Perform E-SATA device check (Procedure 1) Is E-SATA transmission ok? Yes Perform diagnostic check (Procedure 2) No Was an E-SATA problem detected? Yes Perform connection and replacement check (Procedure 3) Replace system board END SatelliteA660/ProA660 Series Maintenance Manual 60 No E-SATA port and transmission are not faulty. Continue troubleshooting - refer to Figure 2.
2Troubleshooting Procedures Figure 2-21 E-SATA troubleshooting process To determine if the computer’s E-SATA system is functioning properly, perform the following procedures. Figure 2-21 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures SatelliteA660/ProA660 Series Maintenance Manual 62
2Troubleshooting Procedures 2.
2Troubleshooting Procedures To determine if the computer’s built-in Felica is functioning properly, perform the following procedures. Figure 2-22 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Felica connection check Procedure 2: Felica replacement check Procedure 1 Felica connection check The Felica is connected via the Felica FPC to the system board. Make sure the Felica FPC cable is firmly connected to the Felica and system board.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures The JET antenna wire, JET module or system board may be the reason of a JET fault. Any of these components may be damaged. To determine if the computer’s JET is functioning properly, perform the following procedures. Figure 2-23 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures SatelliteA660/ProA660 Series Maintenance Manual 67
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Figure 2-24 3D sensor troubleshooting process The operation or system board may be the reason of 3D sensor fault. Either of these two may be damaged. To determine if the computer’s 3D is functioning properly, perform the following procedures. Figure 2-24 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures SatelliteA660/ProA660 Series Maintenance Manual 70
2Troubleshooting Procedures 2.
2Troubleshooting Procedures The system board may be the reason of a Sleep & Charge fault. The system board may be damaged. To determine if the computer’s Sleep & charge is functioning properly, perform the following procedures. Figure 2-25 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: windows application test Procedure 2: Replacement check Procedure 1 windows application test Use windows application to check function can work fine or not.
2Troubleshooting Procedures SatelliteA660/ProA660 Series Maintenance Manual 73
2Troubleshooting Procedures 2.
2Troubleshooting Procedures The system board may be the reason of a CIR fault. The system board may be damaged. To determine if the computer’s CIR is functioning properly, perform the following procedures. Figure 2-27 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures The system board may be the reason of a Sleep & Play music fault. The system board may be damaged. To determine if the computer’s Sleep & Play music is functioning properly, perform the following procedures. Figure 2-25 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures 2.29 Wimax Troubleshooting START Perform Wimax connection check (Procedure 1) Was a Wimax problem delected? Yes Perform connector and replacement check (Procedure 2) Replace Wimax antenna/unit Replace system board END SatelliteA660/ProA660 Series Maintenance Manual 78 No Wimax system is not faulty.
2Troubleshooting Procedures Figure 2-28 Wimax troubleshooting process Notes: Wimax Antenna assemble rule as below: Color of antenna Assemble location White antenna Main/1 Black antenna Aux/2 The Wimax antenna wire, Wimax unit or system board may each be the source of a Wimax fault. Any of these components may be damaged. To determine if the computer’s Wimax system is functioning properly, perform the following procedures. Figure 2-12 outlines the process.
2Troubleshooting Procedures 2.30 3G Troubleshooting START P e r fo rm W in d o w s a p p lic a tio n te s t ( P ro c e d u re 1 ) W a s a 3 G p ro b le m d e te c te d ? No 3 G s y s te m is n o t fa u lty . C o n tin u e tro u b le s h o o tin g - r e f e r to F ig u re 2 .
2Troubleshooting Procedures functioning properly, perform the following procedures. Figure 2-17 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Windows Application check Procedure 2: Connector and replacement check Procedure 1 Windows Application check 1.> Please use TOSHIBA wireless manager. It displays the name of Telecommunication Company, and intensity of an electric wave. 2.> Please choose “About” and click “System Info”.
2Troubleshooting Procedures Procedure 2 Connector and replacement check The 3G antenna, 3G unit or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks. Check 1 Make sure that the 3G antenna is firmly connected to the 3G module (refer to Chapter 4 for instructions) and that the 3G module is securely slotted into the system board. If the problem persists, go to Check 2.
2Troubleshooting Procedures 2.31 LAN Troubleshooting STA R T P e rfo rm d ia g n o s tic check (P ro ced u re 2 ) W as a L A N p ro b le m d e te c te d ? N o L A N is n o t fa u lty .
2Troubleshooting Procedures To determine if the computer’s LAN port is functioning properly, perform the following procedures. Figure 2-19 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Diagnostic check Procedure 2: Connector and replacement check Procedure 1 Diagnostic check Run the test and Diagnostics Program, which will automatically execute the LAN Test. Refer to Chapter 3, Tests and Diagnostics for more information on how to run the program.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Figure 2-31 Ambient Light Sensor troubleshooting process The Cap sensor board or system board may be the reason of an Ambient Light Sensor fault. Either of these two components may be damaged. To determine if the computer’s Ambient Light Sensor is functioning properly, perform the following procedures. Figure 2-31 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
3 Tests and Diagnostics Chapter 3 Tests and Diagnostics SatelliteA660/ProA660 Series Maintenance Manual 1
3 Tests and Diagnostics Contents 3.1 The Diagnostic Test ............................................................................................................ 3 3.2 Executing the Diagnostic Test ............................................................................................ 4 3.3 Display Configuration ........................................................................................................ 7 3.4 Audio sound Test .....................................................
3 Tests and Diagnostics 3.1 The Diagnostic Test This chapter explains how to use the Test & Diagnostic program to test the functions of the (Base on Marseille 10/10G T&D version 1.0) hardware modules. The program consists of a series of tests that run automatically when the Diagnostics Program items are selected and executed. NOTES: To start the diagnostics, follow these steps 1. Check all cables for loose connections. 2. Exit this program when you are at Main Menu.
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Free-Dos are required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: Insert the diagnostics USB memory drive and turn on the computer. (The diagnostics diskette contains the Free-DOS boot files.) And then follow the instructions for T&D program installed in USB memory. You can also use diagnostics CD disk. Turn on the computer and insert the diagnostics CD disk.
3 Tests and Diagnostics The below display will show up at the beginning of T&D program If the test result passes, the following display will show up: SatelliteA660/ProA660 Series Maintenance Manual 5
3 Tests and Diagnostics If an error is detected and a test fails, the following message displays: Whether test result are “PASS” or “FAIL”, Then press any key for next actions – Will go back main menu and copying test log file onto diskette is necessary.
3 Tests and Diagnostics 3.3 Display Configuration This Item will show the unit configuration. It includes: CPU (CPU type /Speed) DDRAM SIZE Panel ID HDD1 type & capacity (Vendor ID. Model .Firmware) VGA CHIP TYPE / VRAM size Wireless type Battery cell (3cell;6cell;9cell;12cell) LAN Type Bluetooth SKUID The screen should display as below: 3.4 Audio sound test The beep sound test program need the user confirm the speaker function by hearing the sound.
3 Tests and Diagnostics And the speaker will send out music during test. NOTE: Remember to tune up the volume as “Maximum” before this test starts. Before Sound test start, you may see notice as below picture: Press any key, then the program will test below item: 1. Line out Left channel test 2. Line out Right channel test 3. Playing 44K wave file 4.
3 Tests and Diagnostics If the function test fail, you can press “N” to stop test, and then it will display as below; Press any key, the program will return to the below display, and you can press “Y” or “N” to SatelliteA660/ProA660 Series Maintenance Manual 9
3 Tests and Diagnostics judge the result. 3.5 Fan ON/OFF/Speed Test The FAN test need the user sense the wind to judge whether the fan is working.
3 Tests and Diagnostics below procedures for this test: The computer will let the fan be “ON” after any key pressed. Feel the wind or listen the rotating sound to check whether the fan is working or not. NOTE: Remember to approach fan outlet that is near left side of unit whether fan is “ON”. The computer will stop the fan working after any key pressed. Feel the wind or listen the sound to check if the fan is “OFF”.
3 Tests and Diagnostics If FAN RPM check is NG, it will show as below: 3.6 Main Battery Charge Test NOTE: The AC adaptor should be connected to successfully run this test . 65W with 19V DC for UMA SKU . 75W with 19V DC for Arrandale CPU and N11M VGA . 90W with 19V DC for Arrandale CPU and N11P VGA, Clarksfield CPU and N11M VGA .
3 Tests and Diagnostics Battery type (Lion) Manufacturer (Sanyo/Panasonic/Sony) Remain charge capacity (0 ~ 100%) Charge function (PASS/FAIL) - “Battery Is Full” showed when “remain charge capacities” is 100% The screen should display as below, if the charge function is OK, will show: If the charge function is NG, the screen will display as: SatelliteA660/ProA660 Series Maintenance Manual 13
3 Tests and Diagnostics SatelliteA660/ProA660 Series Maintenance Manual 14
3 Tests and Diagnostics 3. 7 FDD Test NOTE: Before running the FDD test, prepare a formatted work diskette (1.44 MB). Need to insert FDD when power on machine. Otherwise the Floppy can not be detected. The Floppy Disk Test includes three subtests of the: 1. Sequential seek/verify function (Range: Track 0 ~ 79) 2. Funnel code seek/verify function (Range: Track 0 ~ 79) 3.
3 Tests and Diagnostics 3. 8 Memory check This test will check if the computer’s Memory Frequency and Size is correct in every slot. Before Memory test start, you should choice the below item: 1. Memory Read test 2. Memory Write test 3. Memory Read & Write test 4. Memory INFO test 5.
3 Tests and Diagnostics Memory Read Test Memory Write Test SatelliteA660/ProA660 Series Maintenance Manual 17
3 Tests and Diagnostics Memory Read & Write Test Memory Info Test SatelliteA660/ProA660 Series Maintenance Manual 18
3 Tests and Diagnostics 3. 9 Keyboard Test The keyboard test checks the all keys function. NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test. Before keyboard test starts, the keyboard matrix code should be chosen as below display: 1. S (US, for America) 2. K (UK, for Europe) 3. J (Japan, for Japan) When you execute this test, the keyboard layout is drawn on the display. When any key is pressed, the corresponding key on the screen changes to black as shown below.
3 Tests and Diagnostics UK keyboard Japan keyboard SatelliteA660/ProA660 Series Maintenance Manual 20
3 Tests and Diagnostics 3.10 Mouse (Pad) Test The Mouse test allows the user to select and assign values to the following, using the Touch Pad or “Tab” key to move between selections: 1. Mouse Speed (on a scale from slow to fast) 2. Acceleration (Off, Low, Medium, High) 3. Button Assignments (Left + Right / Right button, either Unassigned or Drag Lock) 4. Swap Buttons (Left /Right) NOTE: The Touch Pad test cannot be used to test an external USB mouse.
3 Tests and Diagnostics 3.11 LCD Pixels Mode Test This LCD pixels mode test checks whether video display is fine. This test includes two modes of the test: 1. Text Mode - including 40*25 (16 colors) and 80*25 (2/16colors) and 320*200(4/16 colors) and 640*200(2/16 colors) and 640*480(2/16 colors) and 640*350(4 colors) 2. VGA Mode - including 320*200 (256 colors) and 640*480 (256 colors).800*600(256 colors).
3 Tests and Diagnostics 3.12 Magnetic Switch Test The Magnetic switch test checks the Magnetic function of the unit. When LCD cover closed, the Magnetic should enable to turn off the display. Follow below steps to run this test: 1. Close the LCD cover. 2. Open the LCD. Then it will indicate whether the test is passed or failed. 1>.
3 Tests and Diagnostics 2>.
3 Tests and Diagnostics 3.13 LAN Test The LAN test checks the LAN full-duplex environment. NOTE: LAN loopback needs to plug in before test begins. And LAN information will show on the test screen: IO Base – Port: A000H IRQ – BH, it’s “IRQ B”. Node – it is “MAC Address”. Line Speed – 1000Mbps or 100Mbps or 10 Mbps. Bus ID – it’s “14”. The LAN test includes three subtests of the: 1. Speed1000 2. Speed100 3. Speed10 The subtests run automatically.
3 Tests and Diagnostics The screen should display as below, indicating whether the subtests pass or fail when finished. If an error is detected and a test fails, the following message displays: 3.
3 Tests and Diagnostics and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. 3.15 BUTTON TEST NOTE: Only for seven buttons SKU.
3 Tests and Diagnostics The tool for seven buttons SKU, the Screen would display as below: SatelliteA660/ProA660 Series Maintenance Manual 28
3 Tests and Diagnostics Mechanical type buttons x 7 to relate with above showed. BUTTON A ECO BUTTON B Wireless on/off BUTTON C Illumination on/off BUTTON D Play/Pause BUTTON E Mute BUTTON F Volume BUTTON G Volume + 3.16 1st HDD Test The HDD test allows the user to verify the 1st HDD ok or not.
3 Tests and Diagnostics The screen will display as below picture to show the subtest is passed or failed when finished: If it is show the picture as below, it means HDD function is OK SatelliteA660/ProA660 Series Maintenance Manual 30
3 Tests and Diagnostics If the picture shows as below, it means he HDD function is NG NOTE: Press “Ctrl+Fn+Break” key to exit the HDD test program. 3.
3 Tests and Diagnostics figure below will be displayed: 3.18 Write DMI When you want to write DMI data, please select which data you want to write, the figure below will be displayed: 1. Write Product (32) 2.
3 Tests and Diagnostics 3. Write Version (32) 4. Write OME string (64) 5. Back to test title After write OK, you should reboot the system that can make the setting effective, or you can write next data before reboot system, the figure below will displayed: NOTE: Should input correct DMI data, and should reboot the system that can make the setting effective.
3 Tests and Diagnostics 3.
3 Tests and Diagnostics This test will check 3D Sensor function by your computer successful or not.
3 Tests and Diagnostics NOTE: Steps 3 Turn run 90 degree whirl, then click enter to test NOTE: Steps 4 Go on Turn run 90 degree whirl, then click enter to test SatelliteA660/ProA660 Series Maintenance Manual 36
3 Tests and Diagnostics NOTE: Step5 Go on Turn run 90 degree whirl, then click enter to test Check test result as below picture, PASS will show “OK”, FAIL will show “NG”.
3 Tests and Diagnostics 3.
3 Tests and Diagnostics EEPROM The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished.
3 Tests and Diagnostics If read T/P type fail, the screen would display as below If W/R T/P type passes, the screen would display as below SatelliteA660/ProA660 Series Maintenance Manual 40
3 Tests and Diagnostics 3.21 EE--PROM Setting This EE-PROM SETTING will set the computer’s function status into EEPROM, included supported function and no support function.
3 Tests and Diagnostics NOTE: Should perform EE-PROM SETTING once change M/B. It defined as normal rule. The screen should display as below: a. Set MIC Function Status in EEPROM (Disable/Enable) b. Set HDMI Function Status in EEPROM (Disable/Enable) c. Set CIR Function Status in EEPROM (Disable/Enable) d. Set Felica card Function Status in EEPROM (Disable/Enable) e. Set KBLED Function Status in EEPROM (Disable/Enable) f. Set Speaker EQ status in EE-PROM (Harman 2 Speaker/ No brand 2 Speaker) g.
3 Tests and Diagnostics When you execute these set, you can press the related number to do. For example: If you want to set MIC function, please press “a” or “A”, the screen will display as below: Please check related information to judge this unit whether has MIC function.
3 Tests and Diagnostics If this unit has no MIC function, press “N” then program will set MIC disable automatically as below: When you “Enable” or “Disable” EE-PROM function are OK, press any key will go back to EEPROM SETTING option as below: You can select “m” or “M” disable all not support function, program will perform automatically as below: SatelliteA660/ProA660 Series Maintenance Manual 44
3 Tests and Diagnostics Press any key you can go back to EE-PROM SETTING option as below: If you select “n” or “N”, program will go back to the Main Menu as below: SatelliteA660/ProA660 Series Maintenance Manual 45
3 Tests and Diagnostics 3.22 Toshiba Logo set Set the computer’s Toshiba Logo for other region except Japan SKU. The screen should display as below, indicating whether the test is passed or failed when finished.
3 Tests and Diagnostics When Toshiba Logo set finish, please restart machine, when show below Logo: SatelliteA660/ProA660 Series Maintenance Manual 47
3 Tests and Diagnostics 3.23 Dynabook Logo set Set the computer’s Dynabook Logo for Japan SKU. The screen should display as below, indicating whether the test is passed or failed when finished.
3 Tests and Diagnostics When Dynabook Logo set finish, please restart machine, when show below Logo: SatelliteA660/ProA660 Series Maintenance Manual 49
4 Replacement Procedures Chapter 4 Replacement Procedures Satellite A660/ProA660 Series Maintenance Manual 4-i
4 Replacement Procedures Chapter 4 4.1 Contents General ................................................................................................................... 4-7 Safety Precautions .......................................................................................... 4-3 Before You Begin ........................................................................................... 4-5 Disassembly Procedures .................................................................................
4 Replacement Procedures Removing the ODD Module (Tray-load) ..................................................... 4-23 Installing the ODD Module (Tray-load) ....................................................... 4-24 Disassembling the ODD (Tray-load)............................................................ 4-24 Assembling the ODD (Tray-load) ................................................................ 4-25 4.8 Logic Upper Assembly ..................................................................
4 Replacement Procedures 4.16 Bluetooth .............................................................................................................. 4-41 Removing the Bluetooth............................................................................... 4-41 Installing the Bluetooth ................................................................................ 4-41 4.17 Thermal Fan .........................................................................................................
4 Replacement Procedures 4.26 WLAN Antennas .................................................................................................. 4-62 Removing the WLAN Antennas .................................................................. 4-62 Installing the WLAN Antennas .................................................................... 4-63 4.27 LCD Panel Hinges ................................................................................................ 4-64 Removing the LCD Panel Hinges .
4 Replacement Procedures Figures Figure 4.1 Removing the Battery Pack .................................................................................. 4-9 Figure 4.2 Removing the HDD door .................................................................................... 4-11 Figure 4.3 Releasing the HDD from the connector.............................................................. 4-12 Figure 4.4 Removing the HDD from the HDD bay .............................................................
4 Replacement Procedures Figure 4.31 Removing the Bluetooth ................................................................................... 4-41 Figure 4.32 Removing the thermal fan ................................................................................ 4-42 Figure 4.33 Removing the TV tuner antenna ....................................................................... 4-43 Figure 4.34 Removing the power membrane .......................................................................
4 Replacement Procedures to this chart, determine the FRUs that need to be removed before removing the suspect FRU. After you determine those FRUs, go to the appropriate sections according to the section numbers shown in the boxes. Then start removal and replacement. 4.2 Battery 4.3 HDD 4.4 Memory 4.5 Keyboard 4.6 TV Tuner Card and WLAN 4.7 ODD module (Tray-load) 4.10 FeliCa Card 4.11 Fingerprint Scanner Bracket 4.12 Touch Pad Board 4.8 Logic Upper Assembly 4.13 Speakers and Speaker Cushions 4.
4 Replacement Procedures Safety Precautions Before you begin disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the original batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the laptop. They may burst or explode. To avoid leakage of alkaline solutions, never heat or disassemble the battery packs. Never throw the battery packs into a fire.
4 Replacement Procedures CAUTION: 1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid laptop failures, never use components that do not meet the specifications. 2. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, paper clips, etc. into the components. When a screw is removed, be sure to replace a screw that is the same size as the original screw.
4 Replacement Procedures Before You Begin Before you begin to disassemble the laptop, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later. Disassemble the laptop only when an abnormality has occurred. Use only the recommended tools.
4 Replacement Procedures Disassembly Procedures The cable connectors come in these two basic types: Pressure plate connectors Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector. To reconnect the cable to the pressure plate's connector, raise the pressure plate up to a satisfactory height and slide the cable into the connector.
4 Replacement Procedures Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components.
4 Replacement Procedures Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows: Screws of an odd-numbered length Blue Screws of a special length Black Screws of a special length are those of a length having decimal places (i.e. 16mm). Symbols of Screws on the Laptop Body For easy maintenance, the screw types are shown on the laptop body as symbols.
4 Replacement Procedures 4.2 Battery Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4.1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the laptop upside down. 2. Slide the battery safety lock to the unlock position. 3.
4 Replacement Procedures Installing the Battery Pack Install the battery pack according to the following procedures. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling or disposal. Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba. NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth. 1.
4 Replacement Procedures 4.3 HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4.2, 4.3, 4.4 and 4.5. 1. Remove one M2.5x8 screw securing the HDD door and remove the HDD door. M2.5x8 Figure 4.
4 Replacement Procedures 2. Use your fingers to push the HDD in the direction indicated by the arrows in Figure 4.3. Figure 4.3 Releasing the HDD from the connector 3. Pull the tab and remove the HDD as shown in Figure 4.4. Figure 4.4 Removing the HDD from the HDD bay NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 4. Place the HDD pack on a flat surface such as a desk.
4 Replacement Procedures 5. Remove the four M3x3 screws with torque value 3.5kgf in order as indicated in Figure 4.5 and separate the HDD foil from the HDD. NOTE: The HDD foil screws on this module are specific to the system. Screws from older systems are not compatible and must not be used on the HDD. M3x3*2 M3x3*2 Figure 4.5 Removing the HDD foil CAUTION: Do not apply pressure to the top or bottom of the drive. Installing the HDD Install the HDD according to the following procedures and Figure 4.6.
4 Replacement Procedures M3x3*2 M3x3*2 Figure 4.6 Securing the HDD foil CAUTION: To prevent the HDD pack from being distorted when installing into the laptop, do not press the center of the HDD pack. Always hold the HDD pack by its sides. 3. Install the HDD pack into the correct position in the laptop. Connect the HDD pack to the laptop. 4. Secure the HDD door by tightening one M2.5x8 screw.
4 Replacement Procedures 4.4 Memory Removing the Optional Memory Remove the optional memory according to the following procedures and Figure 4.7 after checking that the laptop is turned off. CAUTION: Remove the optional memory after turning off the laptop. If this is violated, the laptop or memory can be damaged. 1. Turn the laptop upside down. 2. Loosen the one M2.5x5.6 screw securing the RAM door as shown in Figure 4.7. 3. Remove the RAM door.
4 Replacement Procedures 4. Spread out the two memory lock latches so that the upper memory module pops up. Please follow the procedure as shown in Figure 4.8. Figure 4.8 Removing the RAM from the connectors 5. Pull the upper memory module up and out at an angle, using care to avoid touching the connectors. 6. Repeat steps 4 and 5 to remove the lower memory module. Installing the Optional Memory Install the optional memory according to the following procedures after checking that the laptop is turned off.
4 Replacement Procedures 4.5 Keyboard Removing the Keyboard Remove the keyboard according to the following procedures and Figures 4.9, 4.10, 4.11 and 4.12. 1. Close the laptop and turn it over. Remove the three M2.5x8 screws as shown in Figure 4.9. M2.5x8*3 Figure 4.
4 Replacement Procedures 2. Open the display panel and insert a pin into the opening in the battery bay to push the keyboard free, as indicated in Figure 4.10. Figure 4.10 Releasing the keyboard 3. Lift up the keyboard and free it from the logic upper assembly as shown in Figure 4.11. Figure 4.
4 Replacement Procedures 4. Lift the keyboard up and disconnect the two cables on the back of the keyboard from the motherboard as shown in Figure 4.12. Remove the keyboard. Figure 4.12 Disconnecting the cables and removing the keyboard Installing the Keyboard Install the Keyboard according to the following procedures. 1. Connect the two cables on the back of the keyboard to the motherboard. 2.
4 Replacement Procedures 4.6 TV Tuner Card and WLAN Card Removing the TV Tuner Card Remove the TV tuner card according to the following procedures and Figure 4.13. 1. Disconnect the antenna on the TV tuner card. 2. Remove one M2.5x5 screw on the TV tuner card as shown in Figure 4.13. 3. Pull the TV tuner card out at an angle. M2.5x5*1 Figure 4.
4 Replacement Procedures Removing the WLAN Card Remove the WLAN card according to the following procedures and Figure 4.14. 1. Disconnect the two antennas on the WLAN card. 2. Remove one M2.5x5 screw securing the WLAN card as shown in Figure 4.14. 3. Pull the WLAN card out at an angle. M2.5x5*1 Figure 4.14 Removing the WLAN Card Installing the TV Tuner Card Install the TV tuner card according to the following procedures. 1. Insert the TV tuner card into the connector as shown in Figure 4.13. 2.
4 Replacement Procedures Installing the WLAN Card Install the WLAN card according to the following procedures. 1. Insert the WLAN card into the connector as shown in Figure 4.14. 2. Press the WLAN card down and secure it with one M2.5x5 screw. 3. Connect the black WLAN antenna (auxiliary) to the connector on the left of the WLAN card, and the white WLAN antenna (main) to the connector on the right.
4 Replacement Procedures 4.7 ODD Module (Tray-load) Removing the ODD Module (Tray-load) NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD module according to the following procedures and Figure 4.15. 1. Turn the laptop upside down. 2. Remove one M2.5x8 screw. 3. Pull the ODD module in the direction of the arrow as indicated in Figure 4.15. M2.
4 Replacement Procedures Installing the ODD Module (Tray-load) Install the ODD module according to the following procedures. 1. Insert the ODD into the ODD bay. 2. Slide the ODD inward until it meets the end. 3. Secure the ODD module with one M2.5x8 screw as indicated in Figure 4.15. Disassembling the ODD (Tray-load) NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails.
4 Replacement Procedures ODD bezel hook ODD bezel hook Figure 4.17 Hooks on the inside of the Tray-load ODD bezel Assembling the ODD (Tray-load) Assemble the ODD according to the following procedures. 1. Seat the ODD bracket in the correct position and secure it with two M2x3 screws.
4 Replacement Procedures 4.8 Logic Upper Assembly Removing the Logic Upper Assembly Remove the logic upper assembly according to the following procedures and Figures 4.18, 4.19 and 4.20. 1. Close the laptop and turn it over. Remove the thirteen M2.5x8 screws securing the logic upper assembly as shown in Figure 4.18. M2.5x8*13 Figure 4.18 Removing thirteen screws from the bottom of the laptop 2. Turn the laptop over and open it. Remove the two M2.5x8 screws securing the logic upper assembly. 3.
4 Replacement Procedures Figure 4.19 Disconnecting the cables and removing the upper logic assembly screw 4. Pry up the logic upper assembly from the bottom edge and remove it as shown in Figure 4.20. Figure 4.
4 Replacement Procedures Installing the Logic Upper Assembly Install the logic upper assembly according to the following procedures. 1. Seat the logic upper assembly from the back edge and adjust to the correct position. Snap the logic upper assembly firmly into place. 2. Attach the four cables and secure the logic upper assembly with two M2.5x8 screws as indicated in Figure 4.19. Models featuring the optional FeliCa card will have a fifth connector.
4 Replacement Procedures 4.9 ODD Module (Slot-load) CAUTION: Handle the ODD module carefully. It can become hot during operation. Removing the ODD Module (Slot-load) Remove the ODD (optical disc drive) module according to the following procedures. NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. 1. Remove the logic upper assembly from the system. 2. Lift and remove the ODD frame (straight up) from the logic lower assembly. 3.
4 Replacement Procedures Disassembling the ODD (Slot-load) NOTE: Do not disassemble the ODD when it is working normally. Disassemble or replace the ODD only if it fails. Disassemble the ODD according to the following procedures and Figure 4.21. 1. Remove the two M2x3 screws securing the ODD bracket to the ODD. 2. Remove the ODD bracket from the ODD. 3. Remove the M2x3 screw securing the ODD board to the ODD. 4. Remove the ODD board from the ODD. M2x3*3 Figure 4.
4 Replacement Procedures Assembling the ODD (Slot-load) Assemble the ODD according to the following procedures and Figure 4.21. 1. Place the ODD board in the correct position and secure it with one M2x3 screw. 2. Place the ODD bracket in the correct position and secure it with two M2x3 screws.
4 Replacement Procedures 4.10 FeliCa Card Removing the FeliCa Card Remove the FeliCa card according to the following procedures and Figure 4.22. 1. Turn the logic upper assembly upside down. 2. Remove one M2x2.5 screw securing the FeliCa card to the logic upper assembly. Lift the FeliCa card by the front edge and remove it. M2x2.5 Figure 4.22 Removing the FeliCa card from the logic upper assembly Installing the FeliCa Card Install the FeliCa card according to the following procedures. 1.
4 Replacement Procedures 4.11 Fingerprint Scanner Bracket Removing the Fingerprint Scanner Bracket Remove the fingerprint scanner bracket according to the following procedures and Figures 4.23, 4.24 and 4.25. 1. Turn the logic upper assembly upside down. 2. Use your fingers to press and hold down the wings on either side of the fingerprint scanner bracket as shown in Figure 4.23. Figure 4.
4 Replacement Procedures 3. While still holding down the wings, grasp the fingerprint scanner bracket by the top and bottom edge and work it in the direction indicated in Figure 4.24 until the bracket becomes loose. Figure 4.24 Working the fingerprint scanner bracket loose 4. Lift the edge of the fingerprint scanner bracket as shown in Figure 4.25, and remove it from the system. Figure 4.
4 Replacement Procedures Installing the Fingerprint Scanner Bracket Install the fingerprint scanner bracket according to the following procedures. 1. Turn the logic upper assembly upside down. 2. Use your fingers to press and hold down the wings on either side of the fingerprint scanner bracket as shown in Figure 4.23. 3. Place the bottom edge of the fingerprint scanner bracket in the proper position. 4. Lower the top edge of the fingerprint scanner bracket and press down until it snaps into place.
4 Replacement Procedures 4.12 Touch Pad Board Removing the Touch Pad Board Remove the touch pad board according to the following procedures and Figure 4.26. 1. Disconnect the cable from the touch pad board to the touchpad. 2. Remove the two M2x5 screws securing the touch pad board to the logic upper assembly. Lift the bottom edge of the touch pad board to release it from the tab securing the top edge. Remove the touch pad board. M2x5*2 Figure 4.
4 Replacement Procedures 4.13 Speakers and Speaker Cushions Removing the Speakers Remove the speakers according to the following procedures and Figure 4.27. 1. Pull the FCC cable covering the speaker cables from the slot as indicated in Figure 4.27. 2. Pull the speaker cables from the routing channel. 3. Remove the four M2.5x6.5 screws securing the speakers to the logic upper assembly and remove the speakers. M2.5x6.5*2 M2.5x6.5*2 Figure 4.
4 Replacement Procedures Removing the Speaker Cushions Remove the speaker cushions according to the following procedures and Figure 4.28. 1. Remove the four speaker cushions from the speakers. Figure 4.28 Removing the speaker cushions Installing the Speaker Cushions Install the speaker cushions according to the following procedures. 1. Pinch the speaker cushions and insert them into the speakers. Installing the Speakers Install the speakers according to the following procedures. 1.
4 Replacement Procedures 4.14 Indicator Board Removing the Indicator Board Remove the indicator board according to the following procedures and Figure 4.29. 1. Disconnect the indicator board cable from the motherboard. 2. Lift the indicator board out of the slot and remove it. Figure 4.29 Removing the indicator board Installing the Indicator Board Install the indicator board according to the following procedures. 1.
4 Replacement Procedures 4.15 USB Board Removing the USB Board Remove the USB board according to the following procedures and Figure 4.30. 1. Disconnect the USB board cable from the motherboard. 2. Lift the USB board from the back edge to release it from the catch and remove it. Figure 4.30 Removing the USB board Installing the USB Board Install the USB board according to the following procedure: 1. Seat the USB board in the proper position and snap it into place. 2.
4 Replacement Procedures 4.16 Bluetooth Removing the Bluetooth Remove the Bluetooth according to the following procedures and Figure 4.31. 1. Disconnect the Bluetooth cable from the motherboard. 2. Remove the Bluetooth from the cradle by prying upward on the upper outside edge as shown in Figure 4.31. 3. Remove the Bluetooth. Figure 4.31 Removing the Bluetooth Installing the Bluetooth Install the Bluetooth according to the following procedures. 1.
4 Replacement Procedures 4.17 Thermal Fan Removing the Thermal Fan Remove the thermal fan according to the following procedures and Figure 4.32. 1. Remove the two M2x5 screws from the thermal fan as shown in Figure 4.32. 2. Disconnect the cable from the motherboard. 3. Remove the thermal fan. M2x5*2 Figure 4.32 Removing the thermal fan Installing the Thermal Fan Install the thermal fan according to the following procedures. 1. Seat the thermal fan in the correct position. 2.
4 Replacement Procedures 4.18 TV Tuner Antenna Removing the TV Tuner Antenna Remove the TV tuner antenna according to the following procedures and Figure 4.33. 1. Pull the TV tuner antenna cable from the routing channel and remove the connector from the bracket as shown in Figure 4.33. Remove the TV tuner antenna. Figure 4.33 Removing the TV tuner antenna Installing the TV Tuner Antenna Install the TV tuner antenna according to the following procedure. 1.
4 Replacement Procedures 4.19 Power Membrane Removing the Power Membrane Remove the power membrane according to the following procedures and Figure 4.34. 1. Disconnect the power membrane from the motherboard. 2. Peel off and remove the power membrane, taking care not to damage or tear it. Figure 4.34 Removing the power membrane Installing the Power Membrane Install the power membrane according to the following procedures. 1.
4 Replacement Procedures 4.20 Display Assembly Removing the Display Assembly Remove the display assembly according to the following procedures and Figure 4.35. 1. Lift up the LVDS cable tab as shown in Figure 4.35. 2. Peel back the tape on the LVDS cable connector and disconnect the LVDS cable. 3. Remove the six M2.5x5 screws securing the display assembly as shown in Figure 4.35. 4. Remove the display assembly. M2.5x5*3 M2.5x5*3 Figure 4.
4 Replacement Procedures Installing the Display Assembly Install the display assembly according to the following procedures. 1. Hold the display assembly in the correct position and secure it with four M2.5x5 screws. 2. Connect the LVDS cable to the motherboard and secure the tape. 3. Secure the LVDS cable tab in the correct position as shown in Figure 4.35.
4 Replacement Procedures Motherboard Assembly Removing the Motherboard Assembly The motherboard assembly comes in two different models. Remove the motherboard assembly of each model according to the following procedures and Figures 4.36 and 4.37. 1. Slide the DC in cable upward and remove it from the connector slot as shown in Figure 4.36. Figure 4.
4 Replacement Procedures 2. Remove the M2.5x5 screw securing the motherboard as shown in Figure 4.37. 3. Raise the motherboard from the right edge and slide it out, taking care not to damage the connector ports. M2.5x5*1 Figure 4.37 Removing the discreet motherboard from the system Installing the Motherboard Install the motherboard according to the following procedures. 1. Seat the motherboard in the correct position. 2. Secure the motherboard with one M2.5x5 screw as shown in Figure 4.37. 3.
4 Replacement Procedures 4.21 Thermal Module Removing the Thermal Module The thermal module comes in two different models: a UMA model and a Discrete model. Remove the thermal module of each model according to the following procedures and Figures 4.38 and 4.39. CAUTION: When removing the thermal module, keep the following in mind: 1. The unit can become very hot during operation. Be sure to let it cool down before starting the repair work. 2.
4 Replacement Procedures For the UMA Model 1. Remove the four M2.5x6 screws in order as shown in Figure 4.39. 2. Remove the thermal module. M2.5x6*4 Figure 4.
4 Replacement Procedures Installing the Thermal Module The thermal module comes in two different models: a UMA model and a Discrete model. Install the thermal module of each model according to the following procedures. For the Discrete model 1. Reapply Shinetsu 7762 thermal grease on the VGA thermal pads as shown in Figure 4.40. If you use a new thermal module, remove the release papers on the thermal pads first. thermal grease thermal pads thermal grease thermal pads Figure 4.
4 Replacement Procedures Figure 4.41 Installing the thermal module (Discrete model) For the UMA Model 1. Reapply Shinetsu 7762 thermal grease on the thermal pad as shown in Figure 4.42. If you use a new thermal module, remove the release papers on the thermal pads first. thermal pad thermal grease thermal pads Figure 4.
4 Replacement Procedures 2. Seat the thermal module on the motherboard in the correct position and secure the four M2.5x6 screws according to the number sequence as shown in Figure 4.43. M2.5x6*4 Figure 4.
4 Replacement Procedures 4.22 CPU Removing the CPU Remove the CPU according to the following procedures and Figure 4.44. CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. 1. Use a flat blade screwdriver to unlock the CPU by rotating the cam on the CPU socket counterclockwise to the unlock position, aligning the divot on the cam with the ‘unlocked’ icon as shown in Figure 4.44. 2.
4 Replacement Procedures Installing the CPU Install the CPU according to the following procedures. 1. Check to ensure the cam is in the unlock position. 2. Seat the CPU on the socket, using care not to damage the pins. Align the CPU with the CPU socket using the triangle marker as a guide. 3. Rotate the cam clockwise to the lock position with a flat blade screwdriver.
4 Replacement Procedures 4.23 LCD Bezel Removing the LCD Bezel Remove the LCD bezel according to the following procedures and Figures 4.45 and 4.46. 1. Remove the four rubber seals from the LCD bezel and four M2.5x5 screws securing the LCD bezel to the display assembly as shown in Figure 4.45. M2.5x5*2 M2.5x5*2 Figure 4.
4 Replacement Procedures 2. Pry up the LCD bezel from the outside bottom and outside top edges. Work your way around the outside edges of the LCD bezel until it is free of the display assembly as shown in Figure 4.46. 3. Remove the LCD bezel. Figure 4.
4 Replacement Procedures Installing the LCD Bezel Install the LCD bezel according to the following procedures. 1. Seat the LCD bezel in the correct position on the display assembly. 2. Press the LCD bezel assembly down onto the display assembly until it snaps into place. Work your way around the face of the LCD bezel ensuring that it is securely snapped into place at all points. 3. Secure the LCD bezel to the display assembly with the four M2.5x5 screws and cover the screws with the rubber seals.
4 Replacement Procedures 4.24 LCD Panel Removing the LCD Panel Remove the LCD panel according to the following procedures and Figure 4.47 and 4.48. 1. Remove the four M2.5x5 screws securing the LCD panel to the display assembly. M2.5x5*2 M2.5x5*2 Figure 4.
4 Replacement Procedures 2. Disconnect the Webcam cable. 3. Remove the LCD panel from the display assembly. Figure 4.48 Disconnecting the Webcam Installing the LCD Panel Install the LCD panel according to the following procedures. 1. Seat the LCD panel in the correct position and connect the webcam cable. 2. Secure the LCD panel with the four M2.5x5 screws.
4 Replacement Procedures 4.25 Web Camera Removing the Web Camera Remove the web camera according to the following procedures and Figure 4.49. 1. Peel the web camera upward from the bottom edge and remove it from the display assembly. Figure 4.49 Removing the web camera from the display assembly Installing the Web Camera Install the web camera according to the following procedures. 1. Seat the web camera in the correct position and secure it to the display assembly.
4 Replacement Procedures 4.26 WLAN Antennas Removing the WLAN Antennas Remove the WLAN antennas according to the following procedures and Figure 4.50. 1. Peel back the tinfoil flaps securing the WLAN antennas to the display assembly, taking care not to tear or damage the foil. 2. Pull out the WLAN antenna cables from the routing channels. 3. Peel up the WLAN antennas heads. Remove the WLAN antennas from the system. Figure 4.
4 Replacement Procedures Installing the WLAN Antennas Install the WLAN antennas according to the following procedures. 1. Place the WLAN antenna heads in the correct position and adhere them to the display panel. 2. Route the WLAN antennas in the routing channels. Take care to route the antennas properly through the channels as indicated in Figure 4.51. CAUTION: The black and white WLAN antennas should run parallel to the edge of the LCD display assembly.
4 Replacement Procedures 4.27 LCD Panel Hinges Removing the LCD Panel Hinges Remove the LCD panel hinges according to the following procedures and Figure 4.52. 1. Remove the six M2x3 screws securing the LCD panel hinges to the LCD panel. 2. Remove the LCD panel hinges. M2x3*3 M2x3*3 Figure 4.52 Removing the LCD panel hinges from the LCD Panel Installing the LCD Panel Hinges Install the LCD panel hinges according to the following procedures. 1.
4 Replacement Procedures 4.28 LVDS Cable Removing the LVDS Cable Remove the LVDS cable according to the following procedures and Figure 4.53. 1. Disconnect the LVDS cable from the display assembly. Peel off and remove the LVDS cable from the back of the LCD panel, taking care not to damage the LCD panel. Figure 4.53 Removing the LVDS cable from the LCD panel Installing the LVDS Cable Install the LVDS cable according to the following procedures. 1.
Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling it to prevent damaging it. 1. When installing the LCD module in the display assembly, make sure that you seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
3. If the panel’s surface gets dirty or moist, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a soft cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. CRT Cleaner 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it.
5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module.
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.
Appendix B Appendix B B.
B.
Table B-1 System Board ICs (top and bottom) Number Name U11 Platform Controller Hub (BD82HM55 SLGZS B3) U5 Clock Generator (RTM890N-631-VB-GRT) U19 EC (KB926QFE0) U13 BIOS ROM (4MB SPI) U22 EC ROM (256KB SPI) UA1 CODEC (ALC269Q-VB5-GR) UC2 Card Reader Controller (JMB385-QGAZ0C) UL1 LAN Controller (RTL8105E/RTL8111E -VB-GR) U10 HDMI Level Shift (ASM1442) Table B-2 System Board Connectors (top and bottom) Number Name JCPU CPU Socket JFAN Fan conn. JLVDS LVDS conn. JCRT CRT conn.
J3G 3G conn. JFP Finger Printer conn. JTPL TP& Light Pipe/B conn. J3GSIM 3G SIM CARD conn. PJP1 AC Adaptor conn. PJP2 Battery conn. JCS CapSensor/B conn. JLED LED/B conn. JEXP Express Card conn. JBLG Keyboard LED conn.
B.
B.
Table B-3 System Board ICs (top and bottom) Number Name U11 Platform Controller Hub (BD82HM55 SLGZS B3) U5 Clock Generator (RTM890N-631-VB-GRT) U19 EC (KB926QFE0) U13 BIOS ROM (4MB SPI) U22 EC ROM (256KB SPI) UA1 CODEC (ALC269Q-VB5-GR) UC2 Card Reader Controller (JMB385-QGAZ0C) UL1 LAN Controller (RTL8105E/RTL8111E -VB-GR) U18 HDMI Level Shift (ASM1442) UV1 GPU (nVIDIA N11P/N11M) Table B-4 System Board Connectors (top and bottom) Number Name JCPU CPU Socket JFAN Fan conn.
JMDC MDC conn. J3G 3G conn. JFP Finger Printer conn. JTPL Touch/B conn. J3GSIM 3G SIM CARD conn. PJP1 AC Adaptor conn. PJP2 Battery conn. JCS CapSensor/B conn. JLED LED/B conn. JEXP Express Card conn. JBLG Keyboard LED conn.
C. Appendix C Pin Assignments System Board C.1 JFAN Table C-1 FAN I/F pin assignments (3-pin) Pin No. C.2 Signal name 1 +FAN1 3 GND I/O Pin No. Signal Name 2 FAN_SPEED1 I/O - JLVDS Table C-2 LVDS I/F pin assignments (30-pin) Pin No. Signal name 1 +3VS_LVDS_CAM 3 USB20_P11_R 5 USB20_N11_R 7 GND 9 LVDS_TXOUT0+ 11 LVDS_TXOUT0- 13 LVDS_TXOUT1+ 15 LVDS_TXOUT1- 17 I/O Pin No.
C.3 JLVDS1 Table C-3 LVDS/B pin assignments (10-pin) Pin No. C.4 Signal name I/O Pin No. Signal Name I/O 1 LVDS_TZOUT0+ O 2 LVDS_TZOUT0- O 3 LVDS_TZOUT1+ O 4 LVDS_TZOUT1- O 5 LVDS_TZOUT2+ O 6 LVDS_TZOUT2- O 7 LVDS_TZCLK+ O 8 LVDS_TZCLK- O 9 +5VALW 10 GND JCRT Table C-4 CRT pin assignments (15-pin) Pin No. C.5 Signal name I/O Pin No.
C.6 15 HDMI_SCLK O 16 HDMI_SDATA O 17 GND - 18 +HDMI_5V_OUT O 19 HDMI_HPD O JHDD Table C-6 HDD I/F pin assignments (22-pin) Pin No. Signal name I/O Pin No. Signal Name 1 GND 2 SATA_PTX_C _DRX_P1 3 SATA_PTX_C _DRX_N1 4 GND 5 SATA_PRX_D TX_N1 6 SATA_PRX_D TX_P1 7 GND 8 +3VS 9 +3VS 10 +3VS 11 GND 12 GND 13 GND 14 +5VS 15 +5VS 16 +5VS 17 GND 18 NC 19 GND 20 NC 21 NC 22 NC I/O C.7 JODD Table C-7 SATA ODD I/F pin assignments (13-pin) Pin No.
13 GND C.8 JESATA Table C-8 eSATA/USB I/F pin assignments (11-pin) Pin No. C.9 Signal name I/O Pin No. Signal Name 1 +USB_VCCB 2 USB20_N3_RL 3 USB20_P3_RL 4 GND 5 GND 6 SATA_PTX_C_DRX_P5 7 SATA_PTX_C_DRX_N5 8 GND 9 SATA_PRX_DTX_N5 10 SATA_PRX_DTX_P5 11 GND I/O JBT Table C-9 Bluetooth Connector pin assignments (6-pin) Pin No. Signal name Pin No. Signal Name I/O 1 +BT_VCC - 2 GND - 3 USB20_P5 I/O 4 USB20_N5 I/O 5 BT_RESET# O 6 BT_DET# I C.
C.11 JFEL Table C-11 Felica Connector pin assignments (8-pin) Pin No. Signal name I/O Pin No. Signal Name - 2 USB20_N9 I/O 4 GND 1 +FLICA_VCC 3 USB20_P9 5 NC 6 NC 7 NC 8 NC I/O I/O C.12 JWLAN Table C-12 WLAN Connector pin assignments (52-pin) Pin No. Signal name I/O Pin No. Signal Name A1 NC A2 +3V_WLAN A3 NC A4 GND A5 BT_CTRL A6 +1.
A41 +3V_WLAN A42 LED_WIMAX# A43 GND A44 NC A45 NC A46 NC A47 NC A48 +1.
C.13 J3G Table C-13 3G Connector pin assignments (52-pin) Pin No. Signal name I/O Pin No. Signal Name A1 NC A2 +3VS A3 XBCLKM A4 GND A5 BCCDET A6 +1.5VS A7 CLKREQ_JET# A8 +UIM_PWR A9 GND A10 UIM_DATA A11 CLK_JET# A12 UIM_CLK A13 CLK_JET A14 UIM_RESET A15 GND A16 COMMON A17 BCRSTM A18 ISDBT_DET A19 BCPWON A20 RF_OFF# A21 GND A22 PLT_RST# A23 PCIE_PRX_JETTX _N4 A24 +3VS A25 PCIE_PRX_JETTX _P4 A26 GND A27 GND A28 +1.
C.14 JEXP Table C-14 New Card Connector pin assignments (26-pin) Pin No. Signal name I/O Pin No. Signal Name 1 GND 2 USB20_N4_R 3 USB20_P4_R 4 CP_USB# 5 NC 6 NC 7 PM_SMBCLK 8 PM_SMBDATA 9 +1.5VS_CARD 10 +1.5VS_CARD 11 EC_SWI# 12 +3VALW_CARD 13 PERST# 14 +3VS_CARD 15 +3VS_CARD 16 CLKREQ# 17 EXP_CPPE# 18 CLK_NEW# 19 CLK_NEW 20 GND 21 PCIE_PRX_NEWT X_N3 22 PCIE_PRX_NEW TX_P3 23 GND 24 PCIE_PTX_C_NE WRX_N3 25 PCIE_PTX_C_NE WRX_P3 26 GND - I/O C.
C.16 JLED Table C-16 LED/B Connector pin assignments (12-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +5VALW 2 +5VS 3 WIMAX_LED_GN D# 4 WL_BT_LED# 5 DC_IN 6 PWR_ON_LED# 7 PWR_SUSP_LE 8 HDD_LED# 10 BATT_FULL_LE I/O D# 9 CR_LEDCON# D# 11 12 BATT_CHG_LO W_LED# GND C.17 JDDRH Table C-17 SODIMM I/F pin assignments (204-PIN) Pin No. Signal name I/O Pin No.
35 DDR_A_D11 I/O 36 DDR_A_D15 I/O 37 GND - 38 GND - 39 DDR_A_D16 I/O 40 DDR_A_D20 I/O 41 DDR_A_D17 I/O 42 DDR_A_D21 I/O 43 GND - 44 GND - 45 DDR_A_DQS#2 O 46 DDR_A_DM2 O 47 DDR_A_DQS2 O 48 GND - 49 GND - 50 DDR_A_D22 I/O 51 DDR_A_D18 I/O 52 DDR_A_D23 I/O 53 DDR_A_D19 I/O 54 GND - 55 GND - 56 DDR_A_D28 I/O 57 DDR_A_D24 I/O 58 DDR_A_D29 I/O 59 DDR_A_D25 I/O 60 GND - 61 GND - 62 DDR_A_DQS#3 O 63 DDR_A_DM3 O 64 DDR_A_DQS3 O
111 +1.5V - 112 +1.5V - 113 DDR_A_WE# O 114 DDRA_SCS0# O 115 DDR_A_CAS# O 116 DDRA_ODT0 O 117 +1.5V - 118 +1.5V - 119 DDR_A_MA13 O 120 DDRA_ODT1 O 121 DDRA_SCS1# O 122 NC - 123 +1.5V - 124 +1.
185 GND - 186 DDR_A_DQS#7 O 187 DDR_A_DM7 O 188 DDR_A_DQS7 O 189 GND - 190 GND - 191 DDR_A_D58 I/O 192 DDR_A_D62 I/O 193 DDR_A_D59 I/O 194 DDR_A_D63 I/O 195 GND - 196 GND - 197 GND - 198 PM_EXTTS# O 199 +3VS - 200 PM_SMBDATA I/O 201 GND - 202 PM_SMBCLK I/O 203 +0.75VS - 204 +0.75VS - C.18 JDDRL Table C-18 SODIMM I/F pin assignments (204-PIN) Pin No. Signal name I/O Pin No.
43 GND - 44 GND - 45 DDR_B_DQS#2 O 46 DDR_B_DM2 O 47 DDR_B_DQS2 O 48 GND - 49 GND - 50 DDR_B_D22 I/O 51 DDR_B_D18 I/O 52 DDR_B_D23 I/O 53 DDR_B_D19 I/O 54 GND - 55 GND - 56 DDR_B_D28 I/O 57 DDR_B_D24 I/O 58 DDR_B_D29 I/O 59 DDR_B_D25 I/O 60 GND - 61 GND - 62 DDR_B_DQS#3 O 63 DDR_B_DM3 O 64 DDR_B_DQS3 O 65 GND - 66 GND - 67 DDR_B_D26 I/O 68 DDR_B_D30 I/O 69 DDR_B_D27 I/O 70 DDR_B_D31 I/O 71 GND - 72 GND - 73 DDRB_CKE0
119 DDR_B_MA13 O 120 DDRB_ODT1 O 121 DDRB_SCS1# O 122 NC - 123 +1.5V - 124 +1.
193 DDR_B_D59 I/O 194 DDR_B_D63 I/O 195 GND - 196 GND - 197 GND - 198 PM_EXTTS# O 199 +3VS - 200 PM_SMBDATA I/O 201 +3VS - 202 PM_SMBCLK I/O 203 +0.75VS - 204 +0.75VS - C.19 JKB Table C-19 Keyboard Connector pin assignments (34-pin) Pin No. Signal name I/O Pin No.
C.20 JPIO Table C-20 USB & Audio/B Connector pin assignments (20-pin) Pin No. Signal name I/O Pin No. Signal Name 1 BACK_SENSE 2 NBA_PLUG 3 MIC1_R 4 MIC1_L 5 GNDA 6 HP_L 7 HP_R 8 GND 9 GND 10 USB20_P0_R 11 USB20_N0_R 12 GND 13 GND 14 USB20_P1_R 15 USB20_N1_R 16 +5V_IO 17 +USB_VCCA 18 +USB_VCCA 19 +USB_VCCA 20 +USB_VCCA I/O C.21 JCS Table C-21 FUN/B connector pin assignments (10-pin) Pin No. Signal name I/O Pin No.
C.23 JREAD Table C-23 CARD READER connector pin assignments (36-pin) Pin No. Signal name I/O Pin No.
C.25 JSPK Table C-25 SPK connector pin assignments (4-pin) Pin No. Signal name I/O Pin No. Signal Name 1 SPK_L1 2 SPK_L2 3 SPK_R1 4 SPK_R2 I/O C.26 JTPL Table C-26 TP& Light Pipe/B connector pin assignments (10-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +5VS 2 TP_CLK 3 TP_DATA 4 SW_L 5 SW_R 6 GND 7 TP_LED# 8 KSI6 9 KSO0 10 GND I/O C.27 JBLG Table C-27 Keyboard LED connector pin assignments (4-pin) Pin No. Signal name I/O Pin No.
C.28 JUSB Table C-28 USB connector pin assignments (8-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +USB_VCCC 2 USB20_N2_R 3 USB20_P2_R 4 GND 5 GND 6 GND 7 GND 8 GND I/O C.29 JMDC Table C-29 MDC connector pin assignments (12-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND - 2 +MDC_VCC - 3 AZ_SDOUT_MD O 4 NC - 5 GND - 6 +3VALW - 7 AZ_SYNC_MD O 8 GND - 9 AZ_SDIN1_MD I 10 GND - 11 AZ_RST_MD# O 12 AZ_BITCLK_MD O C.
C.31 PJP2 Table C-31 Battery connector pin assignments (9-pin) Pin No. Signal name I/O Pin No.
Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (2/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (3/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (4/4) Cap No. Code set 1 Keytop Make Code set 2 Break Make Note Break 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 X Fn — — — — *4 X Win E0 5B E0 DB E0 1F E0 F0 1F x App E0 5D E0 DD E0 2F E0 F0 2F Notes: 1. 2. 3. 4. 5. 6. 7. * * * * * * * Scan codes differ by mode. Scan codes differ by overlay function.
Table D-2 Scan codes with left Shift key Cap Key No.
Table D-3 Scan codes in Numlock mode Cap Key Code set 1 No.
Table D-5 Scan codes in overlay mode Cap No.
Table D-7 No.126 key scan code Key top Pause Shift Code set 1 Code set 2 Make Make Common E1 1D 45 E1 Ctrl E0 46 E0 C6 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
Appendix E Key Layout 1. United Status (US) Keyboard Figure US keyboard 2. Traditional Chinese (CH) Keyboard Figure CH keyboard 3.
Figure TI keyboard 4. Korean (KO) Keyboard Figure KO keyboard 5.
Figure UK keyboard 6. US International (UI) Keyboard Figure UI keyboard 7.
Figure HB keyboard 8. Danish (DM) Keyboard Figure DM keyboard 9.
Figure SW keyboard 10. Arabic (ARE) Keyboard Figure ARE keyboard 11.
Figure CZ keyboard 12. Russian (RU) Keyboard Figure RU keyboard 13.
Figure PO keyboard 14. Slovakian (SL) Keyboard Figure SL keyboard 15.
Figure IT keyboard 16. French (FR) Keyboard Figure FR keyboard 17.
Figure GR keyboard 18. Greek (GK) Keyboard Figure GK keyboard 19.
Figure HG keyboard 20. Spanish (SP) Keyboard Figure SP keyboard 21.
Figure TR keyboard 22. Turkish F (TF-F) Keyboard Figure TF-F keyboard 23.
Figure SD keyboard 24. Belgian (BE) Keyboard Figure BE keyboard 25.
Figure YU keyboard 26. Norwegian (NW) Keyboard Figure NW keyboard 27.
Figure ND keyboard 28. Canadian Multinational (AC) Keyboard Figure AC keyboard 29.
Figure CB keyboard 30. Romania (RO) Keyboard Figure RO keyboard 31.
Figure BU keyboard 32. Japanese (JP) Keyboard Figure JP keyboard 32.
Figure LA keyboard SatelliteA660/ProA660 Series Maintenance Manual E17
F. Appendix F Series Screw Torque List (NWQAA/NWQAE) Table F-1 Series Screw Torque List SCREW P/N SCREW SPEC Q'ty LOCATION SCREW TORQUE LCD ASSY M2.0*3 6 LCD BRK TO LCD PANEL(R/L) 1.2~1.5kg MMCK25050G0 M2.5*5 4 LCD BRK L&R to LCD Cover 2.5~3.0 kg MMCK25050G0 M2.5*5 4 LCD Bezel to LCD Cover 2.5~3.0 kg MAAA00153G0 MB MAA000012G0 M2.0*5 2 Battery connector 2.5~3.0 kg MAA000012G0 M2.0*5 2 EXP connector 2.5~3.0 kg MAA000012G0 M2.0*5 2 ODD CONN TO MB 2.5~3.0 kg MAA000012G0 M2.
MMCK25050G0 M2.5*5 1 MB TO LOWER 2.5~3.0 kg MA000005YG0 M2.5*8 2 Low to USB Board to up 2.5~3.0 kg MAA000012G0 M2.0*5 2 FAN module 2.5~3.0 kg MAA000012G0 M2.0*5 2 ODD connector 2.5~3.0 kg MA000005YG0 M2.0*8 2 Low to Up 2.5~3.0 kg MA000005YG0 M2.5*8 1 Low to KB 2.5~3.0 kg MA000005YG0 M2.5*8 14 LOWER TO UPPER 2.5~3.0 kg MA000005YG0 M2.5*8 1 HDD DOOR TO LOWER 2.5~3.0 kg MA0000035G0 M2.5X5.6 1 RAM door to Low 2.5~3.0 kg MA000005YG0 M 2.5*8 1 KB support to low 1.
Appendix G Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component.
