Toshiba Personal Computer Satellite E100 Satellite E105 (PSE10x) Maintenance Manual TOSHIBA CORPORATION S/ No Satellite E100/105 Maintenance Manual
Copyright © 2008 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Satellite E100/105 Maintenance Manual First edition September 2008 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite E100/105, referred to as Satellite E100/105 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention.
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite E100/105 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type.
Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................................1 1.2 System Unit Components ....................................................................................................9 1.3 2.5-inch HDD.....................................................................................................................14 1.4 DVD Super Multi (+-R Double Layer)..................
Procedure 2 Connector Check and Replacement Check.................................... 2-15 2.7 2.8 2.9 2.10 2.11 Display ................................................................................................................. 2-16 Procedure 1 External Monitor Check ......................................................... 2-16 Procedure 2 Test Program Check ............................................................... 2-16 Procedure 3 Connector Check and Replacement Check...............
3.3 3.2.4 Hotkey Test ..............................................................................................8 3.2.5 Audio Play Test........................................................................................8 3.2.6 Audio Record Test ...................................................................................9 3.2.7 DMI Read.................................................................................................9 3.2.8 DMI Write ...................................
Safety Precautions................................................................................................ 4-2 Before You Begin ................................................................................................ 4-4 Disassembly Procedures ...................................................................................... 4-5 Assembly Procedures........................................................................................... 4-5 Tools and Equipment ..........................
Installing the ODD Bay Module ....................................................................... 4-25 4.8 Display Assembly ................................................................................................ 4-26 Removing the Display Assembly....................................................................... 4-26 Installing the Display Assembly ........................................................................ 4-27 4.9 FAN .......................................................
Removing the CCD Board and MIC ................................................................. 4-48 Installing the CCD Board and MIC ................................................................... 4-49 4.19 Power board, Bluetooth card, Button board and Finger print board........................
Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout .................................................................................................B-1 Appendix C Pin Assignments.............................................................................................C-1 Appendix D Keyboard Scan/Character Codes ..................................................................
Chapter 1 Hardware Overview i Satellite E100/E105 Maintenance Manual
1 Hardware Overview ii Satellite E100/E105 Maintenance Manual
1 Hardware Overview Chapter 1 Contents 1.1 Features ............................................................................................................................... 1 1.2 System Unit Components ................................................................................................... 9 1.3 2.5-inch HDD.................................................................................................................... 14 1.4 DVD Super Multi (+-R Double Layer)........................
1 Hardware Overview Figures Figure 1-1 ID Parts Description Placement...............................................................................6 Figure 1-2 Computer Block Diagram........................................................................................7 Figure 1-3 System Board Configurations..................................................................................8 Figure 1-4 System Unit Block Diagram ...............................................................................
1 Hardware Overview 1.1 Features 1.1 Features The Toshiba Satellite E100/E105 is a full size notebook PC based on the Penryn and Merom and Celeron processor, providing high-speed processing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time. The display uses 14.1 inch WXGA CSV LCD panel, at a resolution of 1280 by 800 pixels.
1 Hardware Overview 1.1 Features The computer has two SO-DIMMs slot comes standard with DDRII-800MHz module. It supports PC2-6400 and uses SO-DIMMs (DDRII SDRAM) driven at 1.8 V, accepting BTO/CTO for your memory requirements. It can incorporate up to 8 GB for GM45 and 4GB of main memory for GL40. Using the following sizes of memory modules: y 512 MB (64M×64)/800 MHZ y 1024 MB (128M×64)/800 MHZ y 2048 MB (256Mx64)/800 MHZ y 4096 MB (512Mx64)/800 MHZ Hard Disk Drive (HDD) The computer accommodates 9.
1.1 Features 1 Hardware Overview The keyboard has 3 kinds’ countries key. Battery The computer has a removable 8 Cell Lithium Ion battery pack . Universal Serial Bus (USB) Ports The computer has two USB 2.0 ports and one eSATA (External-SATA) with USB combination port. It is supported to daisy-chain a maximum of 127 USB devices. The serial data transfer rate is 480 Mbps or 12 Mbps and 1.5 Mbps. e-SATA provides more performance than existing solutions .
1 Hardware Overview 1.1 Features The internal LAN board supports 1Gbit, enabling connection to a LAN at up to 1Gbps. It also supports Wake-up on LAN from S3/S4/S5 and PXE boot support. The LAN board has RJ45 jack to directly accommodate a LAN cable. Wireless LAN The internal Mini Card slot supports IEEE802.11bg (WW) / IEEE802.11agn (MOW)/ IEEE802.11bgn (MOW) card. The Antenna has two or three wires dual band antenna support for BTO.
1.1 Features 1 Hardware Overview The FM Tuner Port lets you connect an external FM Antenna. ROBSON Mini Card (BTO) Robson is Intel’s platform non-volatile memory (NVM) disk-cache accelerator which delivers a fast cold boot as well resume from hibernate while saving power. It also accelerates application loading and run time thru intelligent file caching.
1 Hardware Overview 1.1 Features Figures 1-1/1-2/1-3 and 1-4 show the computer and its system unit configuration, respectively.
1.
1 Hardware Overview 1.
1.2 System Unit Components 1 Hardware Overview 1.2 System Unit Components Figure 1-4 is Block Diagram of the System Unit.
1 Hardware Overview 1.2 System Unit Components The system unit of the computer consists of the following components: Processor : Core2 Duo Processor. y Core2 Duo Processor (1066MHz) − Core speed: 2.53/2.80/2.93GHz − System bus: 1066 MHz − On-die level 2 cache: 6 MB − Core speed: 2.00/2.10/2.26/2.40/2.53GHz − System bus: 1066 MHz − On-die level 2 cache: 3 MB y Core2 Duo Processor (800MHz) − Core speed: 1.80/2.00/2.20/2.
1.
1 Hardware Overview 1.2 System Unit Components Card Bus Controller y R5C833 − PCI-1394 bridge interface − SD/Mini SD/SD-IO/MS/MS Pro/MMC/XD Card Controller − PCI Bus interface y R5C837 − SD/Mini SD/SD-IO/MS/MS Pro/MMC/XD Card Controller − PCI Bus interface Audio Controller Realtek ALC268 integrated audio controller supports multimedia. The sound system feature contains the following: y 2 Stereo DACs support 16/20/24-bit PCM format for stereo audio playback.
1.2 System Unit Components − − − − − 1 Hardware Overview Universal I/O port Battery capacity check Flash memory reprogramming function EC access interface I2C communication control Battery EEPROM y 24C02 equivalent (128 words x 16 bits, I2C interface) integrated in battery pack. − Storing records of battery use Clock Generator y ICS9LPRS365 − Generating the clock signal required for the system. LAN Controller y Realtek 8111C 1Gbit − IEEE 802.
1.3 2.5-inch HDD 1 Hardware Overview 1.3 2.5-inch HDD The computer contains an extremely low-profile and lightweight, high-performance HDD. The HDD incorporates 9.5 mm height magnetic disk and mini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 100, 160, 200, 250, 320, 500 GB. The HDD is shown in Figure 1-5 and some of its specifications are listed in Table 1-1.
1.4 DVD Super Multi (+-R Double Layer) 1 Hardware Overview 1.4 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs.
1 Hardware Overview 1.5 Power Supply 1.5 Power Supply The power supply unit provides many different voltages for the system board and performs the following functions: 1. Power input monitor y Checks whether the DC power supply (AC adapter) is connected to the computer. y Checks whether the battery pack is connected to the computer. y Monitors the DC power supply input voltage (AC Adapter output voltage). 2. Power supply's internal control y Turns on and off the battery pack charging power supply.
5B1.6 Batteries 1 Hardware Overview 1.6 Batteries The computer has the following three types of batteries: Main Battery Pack Real Time Clock (RTC) Battery Table 1-3 lists the specifications of these batteries. Table 1-3 Battery specifications Battery Type 8 Cell Main Battery Pack RTC Battery 1.1.1 Material Output voltage Capacity Lithium Ion 10.8 V 5200 mAh Lithium Ion 3.
1 Hardware Overview 1.6 Batteries Table 1-4 Quick/Normal charging time State Charge Time Off-State Charge 8 Cell About 4 hours max On-State Charge 8 Cell About 4~10 hours max NOTE: The time required for normal charge depends on the power consumption by the system. Using the fluorescent lamp and frequently accessing the disk consume much power and lengthen the charge time. Any of the following cases stops battery charge: 7. 1. The battery becomes fully charged. 8. 2.
2 Troubleshooting 2 概要 Chapter 2 Troubleshooting 2-i Satellite E100/E105 Maintenance Manual
2 Troubleshooting Chapter 2 Contents 2.1 Outline.................................................................................................................... 2-1 2.2 Basic Flowchart...................................................................................................... 2-2 2.3 Power Supply ......................................................................................................... 2-6 Procedure 1 Power Icon Check......................................................
2 Troubleshooting Procedure 2Connector Check ........................................................................ 2-21 2.11 Audio Test ............................................................................................................ 2-22 Procedure 1 Test Program Check .................................................................. 2-22 Procedure 2 Connector Check and Replacement Check................................ 2-22 2.12 IEEE 1394 Test .............................................
2 Troubleshooting Figures Figure 2-1 Basic flowchart .............................................................................................. 2-3 Tables Table 2-1 2-iv HDD error code and status...........................................................................
2.1 Outline 2 Troubleshooting 2.1 Outline This chapter describes the fault diagnosis procedures for field replaceable units (FRUs) in the computer. The FRUs covered here are as follows: 1. System board 2. HDD 3. Keyboard 4. Display 5. ODD drive 6. LAN 7. Finger Print 8. Speaker 9. IEEE 1394 10. Cooling module See Chapter 4 for the procedures to replace FRUs and Chapter 3 for the procedures to use test programs The following tools are required to perform the diagnostic procedures: 1.
2 Troubleshooting 2.2 Basic Flowchart 2.2 Basic Flowchart The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU. Before going through the diagnostic flowchart steps, verify the following: Ask the user if a password has been registered and, if so, ask him or her to enter the password. If the user has forgotten the system password, use a jump wire to make a short circuit on M/B B500 location, then turn the computer power on.
2.2 Basic Flowchart 2 Troubleshooting Star t Connect the AC Adapter No Follow the power supply diagnostic procedure in Section 2.3 DC IN LED on ?? Yes No Follow the power supply diagnostic procedure in Section 2.3 BATTERY LED on ?? Yes Turn the power on. Yes Any error message displayed ?? Follow the system board diagnostic procedure in Section 2.4 No No Message "In Touch with Tomorrow Toshiba" displayed Follow the display diagnostic procedure in Section 2.
2 Troubleshooting 2.2 Basic Flowchart 1 No Keyboard works well ?? Follow the keyboard diagnostic procedure in Section 2.6 Insert Bootable CD into ODD No Diagnostic Program Loaded ?? Follow the ODD diagnostic procedure in Section 2.8 Yes Perform each test with the diagnostic program.
2.2 Basic Flowchart 2 Troubleshooting If the diagnostic program cannot detect an error, the error may be intermittent. Run the continuous test program repeatedly to isolate the problem. Check the log utilities function to confirm which diagnostic test detected the error, then perform the appropriate troubleshooting procedures as follows: 1.
2 Troubleshooting 2.3 Power Supply 2.3 Power Supply The power supply in the computer controls many functions and components. To check if the power supply is defective or malfunctioning, follow the troubleshooting procedures below as instructed.
2.3 Power Supply 2 Troubleshooting DC IN LED DC IN LED Power supply status On in White DC power being supplied (from the AC adapter) Off Battery damage and can’t charge during DC-in. Off Else If the DC IN LED off, follow the steps below: 1. Remove the battery pack and the AC adapter to shut off power supply to the computer. 2. Attach the battery and AC adapter back again. If the LED still off, follows the steps below: Check 1 Make sure the DC IN LED goes on in White.
2 Troubleshooting 2.3 Power Supply Procedure 2 Connection Check Power is supplied to the system board as illustrated below: AC adaptor AC power cord System board AC adaptor cord Battery pack Follow the steps below to check whether each connector has been connected correctly: Check 1 Make sure the AC adaptor and AC power cord have been firmly plugged into the DC IN socket and wall outlet, respectively. When they have been connected correctly, perform Check 2.
2.4 System Board 2 Troubleshooting 2.4 System Board To check if the system board is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Test Program Check Procedure 3 Replacement Check Procedure 1 Message Check When the power is turned on, the system performs the self-diagnostic Power On Self Test (POST) embedded in the BIOS ROM. The POST tests and initializes each IC on the system board.
2 Troubleshooting 2.4 System Board Procedure 2 Test Program Check The maintenance test program contains several programs for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Hard Disk test 6. Mouse test 7. ODD test 8. Sound test 9. LAN test If an error is detected during these tests, go to Procedure 3.
2.5 2.5-inch HDD 2 Troubleshooting 2.5 HDD To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Partition Check Procedure 3 Format Check Procedure 4 Test Program Check Procedure 5 Connector Check and Replacement Check CAUTION: The contents of the HDD will be erased when the HDD diagnostic test or formatting is executed.
2 Troubleshooting 2.5 2.5-inch HDD create a DOS partition on drive C. Then restart the computer.. If the problem persists, go to Procedure 3. Check 3 If drive C is listed as active in the FDISK menu, perform Check 4. If drive C is not listed as active, return to the FDISK menu and choose the option to set the active partition for drive C. Then restart the computer. If the problem persists, perform Check 4. Check 4 Enter DIR C: and press the Enter key.
2.5 2.5-inch HDD 2 Troubleshooting Procedure 4 Test Program Check Run the HDD test program stored on the maintenance test program disk for all test items. See Chapter 3 for details on how to use the test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and their status names are listed in Table 2-1. If an error code is not generated and the problem still exists, go to Procedure 5.
2 Troubleshooting 2.5 2.5-inch HDD Procedure 5 Connector Check and Replacement Check The HDD or system board may be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connectors have been firmly connected to the HDD, system board and CPU. HDD System board CPU If any connector is loose or off, reconnect it firmly and return to Procedure 1. If there is still an error, perform Check 2.
2.6 Keyboard 2 Troubleshooting 2.6 Keyboard To check if the computer’s keyboard is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the Keyboard test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 2.
2 Troubleshooting 2.7 Display 2.7 Display To check if the computer’s display is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 External Monitor Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 External Monitor Check Connect an external monitor to the computer's external monitor port, then boot the computer. The computer automatically detects the external monitor even if resume mode is enabled.
2.7 Display Check 3 Check 4 Check 5 2 Troubleshooting The FL may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 4. The FL inverter board may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 5. Make sure the LCD/FL cable has been firmly connected to the system board and LCD module.
2 Troubleshooting 2.9 LAN 2.8 ODD (Optical Disk Drive) To check if the internal ODD drive is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 ODD Cleaning Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 ODD Cleaning Check 1. Turn off the power to the computer. 2. Open the ODD tray by inserting a slender object such as a straightened paper clip into the eject hole.
2.12 LAN Check 3 Check 4 Check 5 2 Troubleshooting The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check 4. The system board may be faulty. Replace it with new one following the instructions in Chapter 4. If the ODD drive is still not functioning properly, perform Check 5. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4.
2 Troubleshooting 2.9 LAN 2.9 LAN To check if the computer’s LAN is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the LAN check program available as part of the maintenance test program. This program will check the LAN. Insert the Bootable CD into the CD. Turn on the computer and run the check program.
Finger Print(Optional)2.10Finger Print(Optional) 2 Troubleshooting 2.10 Finger Print(Optional) To check if the computer’s Finger Print is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check Procedure 1 Test Program Check Execute the Finger Print test program available as part of the maintenance test program. This program checks the Finger Print. Insert the Bootable CD into the CD.
2 Troubleshooting 2.10Audio Test 2.11 Audio Test To check if the computer’s Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the Audio test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 2.
2.12 IEEE 1394 Test 2 Troubleshooting 2.12 IEEE 1394 Test To check if the computer’s IEEE 1394 is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check Procedure 1 Test Program Check Execute the IEEE 1394 test program available as part of the maintenance test program. This program checks the IEEE 1394. Insert the Bootable CD into the CD. Turn on the computer and run the test.
2 Troubleshooting 2.13Cooling Module 2.13 Cooling Module To check if the computer’s cooling module is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the Fan On/off test program available as part of the maintenance test program. This test program checks the cooling module.
2.
Chapter 3 Diagnostic Programs
3 Diagnostic Programs Chapter 3 Contents 3.1 General.......................................................................................................................... 1 3.2 Quick Start .................................................................................................................... 3 3.3 3.2.1 Quick Test ............................................................................................... 3 3.2.2 Customization Test................................................
3 Diagnostic Programs 3.7 Storage ........................................................................................................................ 46 3.8 Video........................................................................................................................... 50 3.9 Communication (COMM) .......................................................................................... 59 3.10 Peripheral ............................................................................
3.1 General 3.1 3 Diagnostic Programs General This chapter explains the diagnostic programs which tests and diagnoses the functions of the hardware components of this computer. The diagnostic programs can be classified into two types: OPTION and DIAGNOSTIC TEST. NOTE 1: This Diagnostic supports Minneapolis10 NOTE 2: Before test must set SATA Controller Mode to “Compatibility” in BIOS Advanced setting, when finished test set it to “AHCI” NOTE 3: Before running a test, be sure to: 1.
3 Diagnostic Programs 3.1 General Before running the diagnostic programs, get the following tools prepared: A Service Diagnostic BOOT CD A Formatted FLOPPY DISK A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test) A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) An External Monitor (for DISPLAY test) A CD-ROM Driver (for CD-ROM test) Audio Line for audio record test A Data CD (for CD-ROM test) The following chapters describe all the test details.
3.2 Quick Start 3.2 3 Diagnostic Programs Quick Start When the system is booting from Service Diagnostic CD, the following screen will be displayed: Please select a test item or select 0 to exit to Free-DOS: 3.2.1 Quick Test When this item is selected, the system will run the configured test items and generate a test report automatically. When the test is completed, a file named Quick.log would be saved in the defined location. When Quick.log is being created, meanwhile, a file named quick.
3 Diagnostic Programs 1. 3.2 Quick Start Use arrow key to select ‘TouchPad’ item on ‘Peripheral’ in the menu, then press Space key to select it. (When it is being selected, there is a X marked in the [ ]) Select ‘Test Mouse’ or press F8 to run the test. The prompt information would be displayed in the screen as below. This test item needs user to verify whether the mouse works normally.
3.2 Quick Start 3 Diagnostic Programs Here is another method to run the test: Highlight a test item by using arrow keys, then, press Enter to start. If there are parameters provided, user should set parameters in the parameter dialog window. CPU Speed Test (Step by Step): 1. Select test item: Select System—CPU—CPU Speed, then, press the Enter key. 2. Parameters Setting Choose the OK button after you set the proper parameters in the following window.
3 Diagnostic Programs 3.2 Quick Start 3. Test Result System will automatically run and display the test result as follows: Following is the comparison report of the two testing methods mentioned above: 1) Configuration and Running As to the method used in Mouse test, the user is required to select test items by pressing Space key and set the parameters artificially, (See 3.3.3 Item’s Parameters Configuration) Then press F8 to start the test.
3.2 Quick Start 3 Diagnostic Programs As to the method adopted in CPU Speed test, user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time. 3.2.3 Keyboard Layout test The test purpose is to check whether 30 kinds of keyboards run well during the test procedure.
3 Diagnostic Programs 3.2 Quick Start It requires user to press the key and check whether the key in the screen changes color or not. User can terminate test by typing ‘END’. When testing the ‘Fn’ key, it must press the ‘Enter’ key at the same time. When the user has checked all the keys and all the keys in the screen have changed color, the diagnostics program would automatically end the test and report the pass information.
3.2 Quick Start 3 Diagnostic Programs 3.2.6 Audio Record Test Check whether the system could record the sound normally. If there is no error during the whole test, Pass; otherwise Fail. The test will repeat for four times. When the test is completed, a file named autest.log will be saved in the defined location. 3.2.7 DMI Read Read the information from the system’s SMBIOS and display it in the screen as follows User can press any key to exit the program. 3.2.
3 Diagnostic Programs 3.2 Quick Start During the editing, user could press F2 to confirm the DMI attribute update or press F4 to ignore the modification. Press ESC to exit the program of DMI Write. The confirmation screen is as below: The attributes that have been modified would be marked in red; otherwise in yellow. User could press F2 to save the changes, or press F4 to ignore and exit the current program. 3.2.9 3D Sensor Test In 3D Sensor test, the system checks whether the HDD protection is normal.
3.2 Quick Start 3 Test1 3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test-Fixture contact is green. Set method of PC Z Upper X Judgment If all data is less than ranges, it will be OK.
3 Diagnostic Programs 4 Test2 3.2 Quick Start The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Rear Upper Judgment If all data is less than ranges, it will be OK.
3.2 Quick Start 5 Test3 3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Right Upper Judgment If all data is less than ranges, it will be OK.
3 Diagnostic Programs 6 Test4 3.2 Quick Start The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Front Upper Judgment If all data is less than ranges, it will be OK.
3.2 Quick Start 7 Test5 3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Left Upper Judgment If all data is less than ranges, it will be OK. 8 Inspection Judgment If all data is less than ranges, it will be OK. 9 Setting When an inspection result is O.K., calibration at HPC. Calibration data If it succeeded, the system will prompt a message of PASS, otherwise the message will be FAIL.
3 Diagnostic Programs 3.2 Quick Start 3.2.10 System Information This function is used to read the system information. When the test is completed, a file named System.log will be saved in the defined location. During the reading process, the following screen will be displayed to indicate that the progress is in detection: On the left column of the above screen, the detected hardware components are listed.
3.2 Quick Start 3 Diagnostic Programs User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current program. On the left column, the components information is listed and user can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component. On the right column, the configuration information of the highlighted component is listed. Press ESC to exit this program. 3.2.
3 Diagnostic Programs 3.2 Quick Start 3.2.12 Exit to Free DOS Select this item to exit to Free DOS. 3.2.13 The Diagnostics Screen Explanation Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Status Area, Progress Bar, Error List, Test Item’s Title, Status Bar and Message Box. 1. Diagnostics Windows When a test item is running, a Diagnostics Windows is displayed in full screen.
3.2 Quick Start 3 Diagnostic Programs The error list of each test module is displayed at the lower right corner of the screen. It would display the total error quantity found in the test, the most recent five error codes and description would be shown here. Detailed error report could be viewed with Logview.exe. When pressing ESC key during the test process, a User Break Windows will be popped up for the user to select. 3.
3 Diagnostic Programs 3.2 Quick Start Test Mode: TIMEBOUND or LOOPBOUND, e.g. LOOPBOUND in the above screen; Script File Name: Script file name, e.g. ‘Custom.INI’ in the above screen; Current Time(C. TIME): Current system time, e.g. ‘C.TIME:2008-02-16 00:42:40’ in the above screen; Test Time Remaining (LEFT): In TIMEBOUND mode, it would display the remaining test time at the same location as Current TIME (C.
3.3 Options 3.3 3 Diagnostic Programs Options 3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s parameters and those parameters created by the LOG file. Options Menu Notes: • Select All/None Items Switch between selecting all test items and selecting none. The hot key is F6. • Test Selected Items Execute all selected test items in this editor. The hot key is F8.
3 Diagnostic Programs 3.3 Options Configure batch parameters and all the test item’s parameters. • Load Batch Parameters Upload all the test items and the parameters to the *.ini file. • Save Batch Parameters Save all the parameters and the test items that are configured in the editor to a specified file. • Log Parameters Configure LOG parameters. • Specify LOG Viewer Specify the viewer for the LOG file.
3.3 Options • 3 Diagnostic Programs Test Order Specify the order of the test items. Choose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence. • Test Options Choose one of the following options: 9 Wait On Error Wait for further confirmation while an error occurs. 9 Break On Error Stop the test when a test item fails.
3 Diagnostic Programs 3.3 Options Monitor the remaining battery capacity (percent). 9 Monitor CPU Thermal Monitor the CPU temperature. • 9 Test Mode LOOPBOUND The chosen test items will run repeatedly according to the times specified in the 'Number of Loops'. 9 TIMEBOUND The chosen test items will run for an extent time specified in 'Time Limit Hrs' and 'Time Limit Min'. • Time Limit Hrs Specify the hours whether 'TIMEBOUND' is chosen under the batch mode.
3.3 Options 3 Diagnostic Programs Repeat times of the test item. • Interactive If the item is enabled during the test, the test items that need user to response can run normally, such as PS2 Mouse test; If it is disabled, those test items will report FAIL. Whether the option here is enabled, it only affects the current test item. • Parameters For the test items with specific parameters, this option will call the related configuration screens.
3 Diagnostic Programs 3.3 Options In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files.
3.3 Options 3 Diagnostic Programs 3.3.6 LOG Parameters Setting You can access the Log Parameters screen through Service Diagnostics\Options Generate Report. • Report Destination If selecting 'NONE', no log file will be generated; if selecting 'FILE', a log file with the name specified in 'Log File Name' will be generated. • Log Options 9 Log Errors If selecting this parameter, errors will be recorded when the test fails.
3 Diagnostic Programs 3.3 Options If selecting this parameter, errors and time will be recorded only when the test fails. 9 Append to Old Log File If selecting this parameter, the new log will be added to the old one. 9 Log Device Info on Fail If selecting this parameter, details of the failed test will be recorded. • Log file Name Specify the Log file name. You can input the detail path of the file. System will show the detail path of the file. 3.3.
3.3 Options 3 Diagnostic Programs In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: • ↑, ↓ Scroll a line backward or forward on the screen.
3 Diagnostic Programs 3.3 Options Scroll a page backward or forward on the screen. • Esc Exit the Log viewer. • F1 Display the Help information about the Log viewer operations and the functional keys. • Ctrl+Home Go to the start of the log file. • Ctrl+End Go to the end of the log file. • Ctrl+F3 Prompt the search dialogue for the user to input the string to be looked for and specify the searching method. • F3 Find the next corresponding strings given. 3.3.
3.3 Options 3 Diagnostic Programs Base Memory Test Extended Memory Test : PASS : PASS End Time: Wed Jul 05 10:47:51 2006 : Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2006.01.
3 Diagnostic Programs 3.4 3.
3.
3 Diagnostic Programs 3.
3.5 System Test 3.5 3 Diagnostic Programs System Test Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item. Subtest 01 CPU 1. Basic Functionality Test This test item is to check whether the CPU works normally through math and logic calculation, which means verifying the general registers, math registers and logic registers. 2. CPU Speed This test item is to detect the work frequency of the current CPU.
3 Diagnostic Programs 3.5 System Test CPU Speed Comparison--Whether you want to make a comparison of the CPU speed with the value set in ‘Expected CPU Speed’, you should choose ‘Yes’; otherwise, ‘No’. Expected CPU Speed--Specify the expected CPU Speed value you want for further comparison. Allowable Error Rate-- Specify the Allowable Error Rate value you want for further comparison. 3.
3.5 System Test 3 Diagnostic Programs 5. CPU Protected Mode Test This test item is to check whether CPU protected mode instruction works normally. 6. MMX The test item is to confirm whether the CPU supports MMX instructions. Subtest 02 Boards 1. DMA Controller This test item is to check whether the DMA controller works normally. 2. Interval Timer This test item is to check whether the Interval Timer (18.2Hz, 55ms) works normally. 3.
3 Diagnostic Programs 3.5 System Test This test item is to check: 1. Whether the current system supports Plug-n-Play; 2. Whether there is an ESCD (Extended System Configuration Data) in the BIOS; 3. Whether there is PCI-to-ISA bridge in the system; 4. Whether there is PCI bus in the system. 6. ACPI Test ACPI test includes two sub-items as below: System Address Map Test: Check the correctness of ACPI system memory map, and whether its mapping scope is within real memory.
3.
3 Diagnostic Programs 3.6 3.6 Memory Test Memory Test This test module is to check whether the memory chip works normally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that includes two sub-items -ROM Read and ROM Write Protection. ROM Read is to check whether BIOS ROM could be correctly read out, ROM Write Protect is to check whether BIOS ROM is write-protected.
3.6 Memory Test 3 Diagnostic Programs Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested.
3 Diagnostic Programs 3.6 Memory Test test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below. Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. 1.
3.6 Memory Test 3 Diagnostic Programs In addition to the above pattern test of the memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory. Below is the parameter dialog window of the extended pattern test. Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole Extended Memory will be tested. Although user can input the parameter into other select box, but the selected result is invalid.
3 Diagnostic Programs 3.6 Memory Test 2. Read Cycle Test Test by using read instructions. Subtest 05 Walking 1’s Test The test item is to ensure that there is no short circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 Pattern’. Subtest 06 Walking 0’s Test The test item is to ensure that there is no open circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 Pattern’.
3.6 Memory Test 3 Diagnostic Programs 2. Random Increment Read/Write This test item is to check whether the memory could be correctly accessed with randomized memory address and a series of incremental data. Subtest 11 Data Bus Test This test item is to check whether the data bus works normally. Subtest 12 Memory Speed Test This test item is to check the data-transferring rate for the cache memory and the system memory.
3 Diagnostic Programs 3.7 3.7 Storage Storage Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect user’s HDD data, the password must be verified before the HDD test. The screen is as follows: Password：hard disk 1. Sequential/Random R/W This test item is to check the HDD’s Read/Write function through data writing and reading to HDD.
3.7 Storage 3 Diagnostic Programs LBA Start, LBA End--Specify the start and end byte in LBA (Large Block Address). Percent—Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested.
3 Diagnostic Programs 3.7 Storage Percent-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. 3. Performance Check the HDD’s seeking speed and transfer the data rate. 4. Controller Check Check the HDD controller’s status, including HDD interrupt and unexpected interrupt. 5.
3.7 Storage 3 Diagnostic Programs Subtest 02 ODD The ODD test runs on IDE CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and performance. 1. Controller Test Check the CDROM controller’s status. 2. Data Transfer Rate Check the data transfer rate of the ODD drive. It will read data from the ODD disc and calculate the data transfer rate. This test needs a data CD. 3. Data CD Butterfly Seek Check the seek function of the ODD drive. It will perform a serial of seeking operations.
3 Diagnostic Programs 3.8 3.8 Video Video This test item tests the video by: 1. 2. displaying the figures in different graphic modes. displaying the property and color of the characters in different text modes. User will confirm whether each video mode works normally by judging whether the display is correct. It checks whether the video memory works normally by writing data into the video memory, then reading it out and comparing the two value. Subtest 01 Text Mode 1.
3.8 Video 3 Diagnostic Programs It would display the below texts of the different attributes in the screen: 1. 2. 3. 4. 5. 6. Text in normal attribute; Text in blinking normal attribute; Text in inverse attribute; Text in blinking inverse attribute; Text in hi-intensity attribute; Text in blinking hi-intensity attribute; Users need to check whether all texts displayed correctly in the above six attributes and key in the answer ‘Y’ or ‘N’ to the prompts ‘Is this display OK? [Y/N]’.
3 Diagnostic Programs 3.8 Video 4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode. The bit4-6 of the attribute byte of a character defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foreground colors (dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and white besides the above 8 colors).
3.8 Video 3 Diagnostic Programs This test item is to check whether 80*25 Text Mode works normally. In the test, user is required to respond according to the instruction in the screen. Subtest 02 640 * 480 VGA Mode This test item is to check whether 680*480 VGA Text mode works normally. In the test, user is required to respond according to the instruction in the screen.
3 Diagnostic Programs Subtest 03 3.8 Video VESA Video Modes This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respond following the instruction in the screen. 1. 640X480 Video Modes Test 2. 800X600 Video Modes Test 3. 1024X768 Video Modes Test 4. 1280X800 Video Modes Test Subtest 04 VESA Video Memory This test item is to check whether VESA video memory could be correctly accessed (write data & read data).
3.8 Video 3 Diagnostic Programs If press Ctrl+Break to force the test to terminate during execution of VESA Video Memory, the test program will not operate and display properly in further tests. Subtest 05 AGP Test This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally. Subtest 06 LCD Panel Test This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens.
3 Diagnostic Programs Subtest 07 3.8 Video Register Test This test item is to check whether the registers of the video adapter works normally. Subtest 08 Color Purity Test This test item is to check whether the system (the video adapter and the display) could display the purity color of red, green, blue, black and white. In the test, user is required to respond according to the instruction in the screen.
3.8 Video Subtest 10 3 Diagnostic Programs DAC/Palette Address This test item is to check the function of DAC registers and Palette registers. In the test, user is required to respond according to the instruction in the screen.
3 Diagnostic Programs 58 Satellite E100 Maintenance Manual 3.
3.8 Video 3.9 3 Diagnostic Programs Communication (COMM) Subtest 01 LAN Card This test item is to check whether the module can detect the existence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the network card. 2. Vendor ID Detection Detect the vendor ID of the network card. 3. MAC Address Detection Detect the MAC address of the network card.
3 Diagnostic Programs 3.10 Peripheral 3.10 Peripheral Subtest 01 Keyboard This test item is to check whether the keyboard works normally. 1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Clock Line Test Check whether the keyboard clock line works normally. Subtest 02 Mouse Test Check whether the point devices work normally. 1.
3.10 Peripheral Subtest 03 3 Diagnostic Programs Led Test 1. Led Test Check whether the green and white led works normally.
3 Diagnostic Programs Check whether the orange led works normally. Check whether the HDD led works normally. 62 Satellite E100 Maintenance Manual 3.
3.11Error Codes and Description 3 Diagnostic Programs 3.11 Error Codes and description The format of ‘Error Code’ is ‘ddxxee’, and ‘dd’ is the device ID (1~2 chars), ‘xx’ is test function ID of device (2 chars), ‘ee’ is the error code of device (2 chars); the range of error code is from 01 to 99 in each device (the common error codes in all device are set to 99 and spanned).
3 Diagnostic Programs 3.11Error Codes and Description 04 The test pattern read out from the extension memory is different As above. (XMS)Memory Problem from the one that has been written in this address. 05 (XMS) Out Of Range 06 Address Test Error 07 Toggle Bit Error 08 Interval Error Wrong parameters setup. Check and reset the parameters. Interference between different address channels. Errors with the timer chip. The acquired refreshing frequency is out of the estimated range.
3.11Error Codes and Description 3 Diagnostic Programs configuration. 17 PCI to ISA Bridge Error PCI-ISA bridge errors. 18 53 ESCD Error ACPI Table Test Error FAN Fan Slow Speed Test Fail Fan Stop Test Fail Fan Fast Speed Test Fail Video ESCD errors. Errors with the ACPI table test. Repeat multiple times. If there is always the same error, replace the board. As above. As above. The fan slow speed test fails. The fan stop test fails. The fan fast speed test fails. Check the FAN connection. As above.
3 Diagnostic Programs 15 16 17 19 20 21 Check whether there is any Physical problems with the video physical problem with the video VESA VRAM Test Error card or the monitor. card or the monitor. Check and see whether the AGP AGP configuration register AGP Test Error video card has any physical errors. problem. LCD Panel Test Error Lower LCD color resolution. Replace the LCD. Physical problems with the video Check and see whether the video Register Test Error card. card has any physical problem.
3.11Error Codes and Description 01 03 04 05xx 01 28xx 3 Diagnostic Programs Keyboard Map & Stroke Test Fail Clock Line Test Fail Data Line Test Fail Mouse Keyboard Map & Stroke Test fails. Clock Line Test fails. Data Line Test fails. Check the KBD connection and repeat the test. As above. As above. Touch Pad Test Fail Touch Pad Test Fail Check the mouse connection and repeat the test. Can not find IEEE1394 controller Don’t support 1394.
3 Diagnostic Programs 09 Eject Error 68 Satellite E100 Maintenance Manual 3.11Error Codes and Description Wrong CD-ROM drive. Exit from the wrong drive.
3.12 Quick Test Item List 3 Diagnostic Programs 3.
Chapter 4 Replacement Procedures 4 1
4 Replacement Procedures 4-ii Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual
4 Replacement Procedures Chapter 4 Contents 4.1 General....................................................................................................................... 4-1 Safety Precautions................................................................................................ 4-2 Before You Begin ................................................................................................ 4-4 Disassembly Procedures .......................................................................
4 Replacement Procedures 4.6 HDD......................................................................................................................... 4-21 Removing the HDD ........................................................................................... 4-21 Installing the HDD............................................................................................. 4-23 4.7 ODD Bay Module ...................................................................................................
4 Replacement Procedures Installing the FL Inverter Board ........................................................................ 4-44 4.17 LCD Modules........................................................................................................... 4-45 Removing the LCD Modules ............................................................................. 4-45 Installing the LCD Modules .............................................................................. 4-47 4.18 CCD Board and MIC .
4 Replacement Procedures Figures Figure 4-1 Removing the battery pack ................................................................................. 4-8 Figure 4-2 Removing the battery pack ................................................................................. 4-8 Figure 4-3 Removing the PC card ...................................................................................... 4-10 Figure 4-4 Removing the Memory Card.........................................................................
4 Replacement Procedures Figure 4-32 Removing the 15.1-inch LCD cable................................................................ 4-47 Figure 4-33 Removing the CCD board and MIC................................................................ 4-48 Figure 4-34 Removing Power board, Bluetooth card, Button board and Finger print board ..
Error! Style not defined. General 4 Replacement Procedures 4 1 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations.
4 Replacement Procedures 4.1 General Safety Precautions Before you begin to disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the genuine batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. To avoid leakage of alkaline solutions, never heat or disassemble the battery packs.
Error! Style not defined. General 4 Replacement Procedures CAUTION: 1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications. 2. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, paper clips, etc. into the components. When a screw is removed, be sure to replace a screw that is the same size as the original screw.
4 Replacement Procedures 4.1 General Before You Begin Before you begin to disassembly the computer, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later. Disassemble the computer only when an abnormality has occurred. Use only the recommended tools.
Error! Style not defined. General 4 Replacement Procedures Disassembly Procedures The cable connectors come in these two basic types: Pressure plate connectors Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector. To reconnect the cable to the pressure plate's connector, raise the pressure plate up to a satisfactory height and slide the cable into the connector.
4 Replacement Procedures 4.1 General Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components.
Error! Style not defined. General 4 Replacement Procedures Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows: Screws of an even-numbered length Brown Screws of an odd-numbered length White Screws of a special length Black Screws of a special length are those of a length having decimal places, such as 2.5 mm and 2.6 mm.
4 Replacement Procedures 4.1 General Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4-1, 4-2. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the computer upside down so that the back is facing you. 2. Slide out the battery lock. 3. Slide the battery release latch and remove the battery pack from the computer.
Error! Style not defined. General 4 Replacement Procedures Installing the Battery Pack Install the battery pack according to the following procedures and Figure 4-1, 4-2. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling, or disposal. Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba. NOTE: Visually check the battery's terminals.
4 Replacement Procedures 4.1 General Removing the Optional PC Card Remove the optional PC card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. CAUTION: Install or remove the PC card correctly, according the manuals for the PC card and the operating system you are using. 1. Push the eject button for the PC card to be removed until it stops then release the button. 2. When the eject button pops out slightly, push it again. 3.
Error! Style not defined. General 4 Replacement Procedures Installing the Optional PC Card Install the optional PC card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Insert the PC card gently until it stops and is seated securely. 2. After checking that the PC card is seated securely, push the PC card release lever slightly.
4 Replacement Procedures 4.1 General Removing the Memory Card Remove the memory card according to the following procedures and Figure 4-4, after checking that the computer is turned off in boot mode. 1. Push the memory card to be removed until it stops then release the memory card. 2. When the memory card pops out, grasp it and pull it out.
Error! Style not defined. Error! Style not defined. 4.2 4 Replacement Procedures Keyboard Cover and Keyboard Removing the Keyboard Cover and Keyboard Remove the Keyboard Cover and Keyboard according to the following procedures and Figure 4-5, 4-6. 1. Release the following 13 latches on the keyboard cover, in that order: - Five bottom latches. - Six front latches. One latch on each right and left side. 2. Remove the keyboard cover 3. Remove two M2x4 black flat-head securing screws. 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the Keyboard Cover and Keyboard Install the Keyboard cover and keyboard according to the following procedures and Figure 45, 4-6. 1. Connect the keyboard cable to CN6 and CN8 on the system board. 2. Secure the keyboard with two M2x4 black flat head screws. 3. Place the keyboard cover in the correct position and secure the following 13 latches, in that order: - Five bottom latches. - Six front latches.
Error! Style not defined. Error! Style not defined. 4.3 4 Replacement Procedures Optional Memory Removing the Optional Memory Remove the optional memory (module) according to the following procedures and Figures 47, after checking that the computer is turned off in boot mode. CAUTION: Remove the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged. CAUTION: Do not touch the connectors on the memory modules or in the computer.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the Optional Memory Install the optional memory (module) according to the following procedures and Figures 4-7, after checking that the computer is turned off in boot mode. Note: The slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A. CAUTION: Install the optional memory after turning off the computer.
Error! Style not defined. Error! Style not defined. 4.4 4 Replacement Procedures UWB Module Removing the UWB Module Remove the UWB Module according to the following procedures and Figures 4-8, after checking that the computer is turned off in boot mode. 1. Remove the two M2x4 black flat-head screws securing the UWB module. 2. Remove the UWB module. M2x4 .
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the UWB Module Install the UWB module according to the following procedures and Figures 4-8, after checking that the computer is turned off in boot mode. 1. Insert the UWB module in to the connector. 2. Secure the UWB module with two M2x4 black flat head screws.
Error! Style not defined. Error! Style not defined. 4.5 4 Replacement Procedures Top Cover Removing the Top Cover Remove the top cover according to the following procedures and Figures 4-9 and 4-10. 1. Turn the computer upside down and remove the following fifteen screws in the order shown on figure4-9. - Six M2.5x7 black flat head screws. - One M2.5x4 black flat head screws. - Eight M2x2.5 black flat head screws. M2 . 5x7 black flat head screw M2x2 .
4 Replacement Procedures 4.5 Top cover 2. Restore the normal computer placement. 3. Disconnect the touch pad board flat cable from CN25, Finger print cable from CN51 MMB board flat cable from CN18, Power board flat cable from CN9 and Bluetooth card cable from CN27. 4. Remove the four M2x3 black flat head screw securing the top cover. 5. Lift up the top cover Installing the Top Cover Install the top cover with the display assembly according to the following procedures and Figures 4-9, 4-10. 1.
Error! Style not defined. Error! Style not defined. 4.6 4 Replacement Procedures HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4-11, 4-12. 1. Release the three M2x4 black flat screws securing the HDD. 2. Pull out the HDD, following the direction of the arrow.
4 Replacement Procedures 4.6 Error! Style not defined. 5. Remove the HDD connector M3x3 . 5 black flat head screw HDD HDD chassis connector M3x3 . 5 black flat head screw HDD pack Figure 4-12 Removing the HDD chassis CAUTION: Do not apply pressure to the top or bottom of the drive.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Installing the HDD Install the HDD according to the following procedures and Figures 4-11, 4-12. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Attach the HDD chassis. 2. Secure the HDD and its chassis with four M3x3.5 black flat head screws. CAUTION: To prevent the HDD bracket from being distorted when installing the HDD pack into the computer, do not press the center of the HDD pack.
4 Replacement Procedures 4.7 4.7 Error! Style not defined. ODD Bay Module Removing the ODD Bay Module NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the following procedures and Figures 4-13. 1. Remove the M2x4 black flat head screw. 2. Push out on the ODD bay module in the direction of the arrow.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-14. 1. Remove two M2x4 black flat head screws securing the ODD bracket. 2. Remove the bracket. 3. Remove the ODD bezel.
4 Replacement Procedures Error! Style not defined. Display Assembly 4.8 Display Assembly Removing the Display Assembly CAUTION: Use care to avoid that the antenna cable is not caught between the display assembly and computer. Remove the display assembly according to the following procedures and Figures 4-15, 4-16. 1. Remove two M2.5x6 black flat head screws in the order shown on the figure4-15. 2.
4.8 Error! Style not defined. 4 Replacement Procedures M2 . 5x4 black flat head screw MIC cable CCD cable LCD FL cable Cable fillister Wireless Lan antenna TAPE CN7 CN10 CN12 Cable fillister Figure 4-16 Removing the display assembly Installing the Display Assembly Install the display assembly according to the following procedures and Figures 4-15, 4-16. 1. Place the display panel in the correct position. 2. Secure six M2.5x4 black flat head screws securing the LCD module to the button cover. 3.
4 Replacement Procedures Error! Style not defined. FAN 4.9 FAN Removing the FAN Remove the FAN according to the following procedures and Figures 4-17. 1. Disconnect the FAN cable from CN2. M2x5 white flat head screw CN2 FAN Figure 4-17 Removing the FAN 2. Remove three M2x5 white flat head screws on the FAN 3. Remove the FAN. Installing the FAN Install the FAN according to the following procedures and Figures 4-17. 1. Seat the FAN in to correct position. 2. Connect the FAN cable to CN2. 3.
Error! Style not defined. Error! Style not defined. 4.10 4 Replacement Procedures CPU Cooling Module CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before starting the repair work. Do not touch or cause damage to the fan in the cooling module. Remove the CPU cooling module and fan according to the following procedures and Figures 4-18, 4-19, 4-20, 4-21. 1.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Figure 4-19 Applying silicon grease 1. If the thermal pad is broken, replace new thermal pad into correct position, thermal pad part number is V000934150. Figure 4-20 Replace new thermal pad into correct position. 2. Tear down the tap on the thermal pad.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Install the cooling Module according to the following procedures and Figures 4-18, 4-19, 420, 4-21. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the correct position for the module. 2. Secure the relevant screws on the main board according to the number sequence sealed on the heat sink module.
4 Replacement Procedures 4.11 Error! Style not defined. Error! Style not defined. CPU Removing the CPU CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. Remove the CPU according to the following procedures and Figures 4-22, 4-23 and 4-24. NOTE: FOXCONN CPU socket will be 180 degrees to the right. 1.
4.11 CPU 4 Replacement Procedures Installing the CPU Install the CPU according to the following procedures and Figures 4-22, 4-23, 4-24. 1. Check that the triangle on the cam is in the unlock position. 2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide. 3. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver. 4. NOTE: FOXCONN CPU socket will be 180 degrees to the left.
4 Replacement Procedures Error! Style not defined. Error! Style not defined.
4.12 Speakers and Wireless LAN 4.12 4 Replacement Procedures Speakers and Wireless LAN Removing the Speakers and Wireless LAN. Remove the Speakers and Wireless LAN according to the following procedures and Figure 4-25. 1. Disconnect the left speaker cable from CN26 and right speaker from CN29. 2. Remove two M2x4 black flat head screws securing the left speaker. 3. Remove two M2x4 black flat head screws securing the right speaker. 4. Remove the left and right speakers. 5.
4 Replacement Procedures 4.12 Speakers and Wireless LAN Installing the Speakers and Wireless LAN Install the speakers and Wireless LAN according to the following procedures and Figure 425. 1. Seat the left and right speaker in the correct position. 2. Secure the left and right speakers with four M2x4 black flat head screws. 3. Connect the left speaker cable in to CN26 and right speaker in to CN29. 4. Seat the Wireless LAN in to correct position. 5.
4.13 System board 4.13 4 Replacement Procedures System Board Removing the System Board. NOTE: Be careful of the eject button for the PC card. It can be damaged when removing the board. Make sure it is securely installed. Remove the System Board according to the following procedures and Figure 4-26. 1. Release four M2.5x4 white flat head screws on the system board. 2. Release three M2.5x4 white hexagonal screws on the system board. 3. Release two M2x4 black flat head screws securing the Mini card. 4.
4 Replacement Procedures 4.13 System board Installing the System Board Install the System Board according to the following procedures and figure 4-26. NOTE: Be careful of the eject button for the PC card. It can be damaged when installing the system board. Make sure it is pushed in. 1. Seat the system board in the correct position. 2. Secure the system board with four M2.5x4 white flat head screws on the button cover. 3. Secure three M2.5x4 white hexagonal screws on the system board. 4.
4.14 USB board, DC-IN FM card and RGB cable 4.14 4 Replacement Procedures USB board, DC-IN, FM card and CRT cable Removing the USB board, DC-IN, FM card and CRT cable. Remove the USB board, DC-IN, FM card and CRT cable according to the following procedures and Figures 4-27. 1. Release one M2x4 black flat head screw securing the USB cable. 2. Remove USB cable. 3. Release two M2.8x4.5 black flat head screws securing the CRT cable. 4. Remove CRT cable. 5. Remove DC-IN cable from the base enclosure. 6.
4 Replacement Procedures 4.14 USB board, DC-IN FM card and RGB cable Installing the USB board, DC-IN, FM card and CRT cable Install the USB board, DC-IN, FM card and CRT cable according to the following procedures and Figure 4-27. Note: Be careful of the kill switch button for the USB board. It can be damaged when installing the USB board. Make sure it is in the correct position. 1. Connect the FM card cable in to CN2002 and seat the FM card in the correct position. 2.
4.15 Display Mask 4 Replacement Procedures 4.15 Display Mask Removing the Display Mask Remove the display mask according to the following procedures and Figure 4-28. 1. Remove the following 4 seals on the display module in that order: - Two gray seals on the bottom - Two gray seals on the top 2. Remove the following 4 screws on the display module, in that order: - Two M2.5x4 black flat head screws on the top - Two M2.5x4 black flat head screws on bottom 3.
4 Replacement Procedures 4.15 Display Mask Installing the Display Mask Install the display mask according to the following procedures and Figure 4-28. 1. Seat the display mask in the correct position and secure the following 19 latches, in that order: - Four latches on the left side - Four latches on the top side. - Four latches on the right side. - Seven latches on the bottom side 2. Secure the display mask with the following 4 screws, in that order: - Two M2.
4.16 FL Inverter Board 4 Replacement Procedures 4.16 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figures 4-29. 1. Remove one M2.5x5 black flat head screw securing the inverter board. 1. Lift the LCD module, FL inverter board and disconnect the LCD/FL cable from the LCD/FL connector. 2. Disconnect the HV cable from the HV connector and remove the FL inverter board M2 .
4 Replacement Procedures 4.16 FL Inverter Board Installing the FL Inverter Board Install the FL inverter board according to the following procedures and Figures 4-29. 1. Connect the LCD/FL cable to LCD/FL connector, and connect the HV cable to the HV connector. 2. Seat the LCD module, FL inverter board in the correct position. 3. Securing the inverter board with one M2.5x5 black flat head screw.
4.17 LCD Module 4 Replacement Procedures 4.17 LCD Modules NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module. NOTE: Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or regulations. NOTE: The LCD/FL cable must be carefully peeled away before disconnecting it from the module. Removing the 15.1-inch LCD module Remove the 15.1-inch LCD module according to the following procedures and Figures 430, 4-31, 4-32. 1.
4 Replacement Procedures 4.17 LCD Module M2 . 5x5 black flat head screw Figure 4-30 Removing the 15.1-inch LCD module and screws Right LCD bracket Left LCD bracket LCD module M2x3 black flat head screw M2x3 black flat head screw . M2 5x5 black flat head screw Figure 4-31 Removing the 15.
4.17 LCD Module 4 Replacement Procedures Figure 4-32 Removing the 15.4-inch LCD cable Installing the 15.1-inch LCD Module NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module. Install the 15.1-inch LCD module according to the following procedures and Figures 4-30, 4-31, 4-32. 1. Turn the LCD upside down. 2. Connect the LCD/FL cable to the LCD module connector. 3. Turn the LCD right side up. 4. Please the LCD module in the correct position and secure it with two M2.
4.18 CCD Board and MIC 4 Replacement Procedures 4.18 CCD Board and MIC Removing the CCD Board and MIC Remove the FL inverter board according to the following procedures and Figure 4-33. 1. Disconnect the CCD cable from the CCD module connector and remove the CCD board. 2. Lift the MIC from the display rear cover.
4 Replacement Procedures 4.18 CCD Board and MIC Installing the CCD Board and MIC Install the FL inverter board according to the following procedures and Figure 4-33. 1. Connect the CCD module cable to CCD module connector. 2. Seat the CCD module, MIC in the correct position.
4.19 Power board, Switch board, Touch Pad board 4 Replacement Procedures 4.19 Power board, Bluetooth card, Button board and Finger print board. Removing the Power board, Bluetooth card, Button board and Finger print board. Remove the Power board, Bluetooth card, Button board and Finger print board according to the following procedures and Figure 4-34. 1. Release one M2x3 black flat head screw securing the power board. 2. Remove the power board. 3. Disconnect the MMB board flat cable from MMB board. 4.
4 Replacement Procedures 4.19 Power board, Switch board, Touch Pad board M1 . 6x2 . 5 white flat head screw Touch pad flat cable Button board flat cable M2 .
6000 1 次 Appendices
Appendices Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout .................................................................................................B-1 B.1 System Board Front View ......................................................................................B-1 B.2 System Board Back View ......................................................................................
Appendices C.24 CN25 MB to Touch Pad Board Connector (8-Pin) .................................... C-12 C.25 CN26 Internal Speaker Left Connector (2-Pin) ......................................... C-12 C.26 CN27 Blue Tooth Module Connector (10-Pin).......................................... C-12 C.27 CN28 Fingerprint Module Connector (4-Pin)............................................ C-12 C.28 CN29 Internal Speaker Right Connector (2-Pin) ....................................... C-13 C.
Apx. A Handling the LCD Module Appendices Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
Appendices Apx. A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. Also, never scratch the surface. 4.
Apx. A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.
Appendices Apx. A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
Apx. A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization.
Apx. B Board Layout Appendices Appendix B Appendix B Board Layout B.
Appendices B.2 Apx.
Appendices Apx. C Pin Assignments Appendix C C.1 CN1 Battery Pack Connector (9-Pin)......................................................... C-3 C.2 CN2 FAN Connector (3-Pin) ..................................................................... C-3 C.3 CN3 MB to CRT Board Connector (14-Pin) ............................................. C-3 C.4 CN4 Robson Card Module Connector (52-Pin)......................................... C-4 C.5 CN5 Keyboard LED Cable Connector (4-Pin) ..................
Appendices Apx. C Pin Assignments C.32 JACK1 RJ45 LAN Connector (12-Pin) ........................................................C-19 C.33 JACK2 External MIC Connector (6-Pin)......................................................C-19 C.34 JACK3 Head Phone Connector (6-Pin) ........................................................C-20 C.35 CN2000 CRT Board Connector (15-Pin)........................................................C-20 C.36 CN2001 CRT Port Connector (15-Pin).....................
Appendices Apx. C Pin Assignments Appendix C Appendix C Pin Assignments System Board C.1 CN1 Table C-1 Battery Pack Connector (9-Pin) Battery Pack Connector Pin Assignments (9-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 BATT+ O 2 BATT+ O 3 ID O 4 DGND - 5 TS I 6 SMD I/O 7 SMC I/O 8 DGND - 9 DGND - - - - C.2 CN2 Table C-2 FAN Connector (3-Pin) FAN Connector Pin Assignments (3-Pin) Pin No. Signal Name I/O Pin No.
Appendices C.4 CN4 Table C-4 Robson Card Module Connector (52-Pin) Robson Card Module Connector Pin Assignments (52-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PCIE_WAKE# I/O 2 +V3S O 3 CH_DATA I/O 4 DGND - 5 CH_CLK I/O 6 +V1.
Appendices Apx. C Pin Assignments 1 DGND - 2 - - 3 - - 4 +V5S O C.6 CN6 Table C-6 AC-In Cable Connector (4-Pin) AC-In Cable Connector Pin Assignments (4-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 +VADPTR - 2 +VADPTR - 3 DGND - 4 DGND - C.7 CN7 Table C-7 Internal MIC Connector (2-Pin) Internal MIC Connector Pin Assignments (2-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 MIC_IN I C.
Appendices Apx. C Pin Assignments 29 +V3S O 30 - - 31 - - 32 DGND - 33 - - 34 +V3S O C.9 CN9 Table C-9 Power Board Connector Pin Assignments (4-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 PWRBTN_LED O 3 PWR_SWIN#_3 I 4 +V5S - C.10 CN10 Table C-10 Camera Cable Connector (5-Pin) Camera Cable Connector Pin Assignments (5-Pin) Pin No. Signal Name I/O Pin No.
Appendices Apx.
Appendices Apx. C Pin Assignments Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 SATA_C_TXP5 O 3 SATA_C_TXN5 O 4 DGND - 5 SATA_C_RXN5 I 6 SATA_C_RXP5 I 7 DGND - 8 - - 9 +V5S O 10 +V5S O 11 - - 12 DGND - 13 DGND - - - - C.15 CN16 Table C-15 1394 Connector Pin Assignments (4-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 1394_L_TPB0N I/O 2 1394_L_TPB0P I/O 3 1394_L_TPA0N I/O 4 1394_L_TPA0P I/O C.
Appendices C.18 Apx. C Pin Assignments CN19 Table C-18 5 In 1 Card Connector (40-Pin) 5 In 1 Card Connector Pin Assignments (40-Pin) Pin No. Signal Name I/O Pin No.
Appendices C.20 Apx. C Pin Assignments CN21 Table C-20 SATA HDD Connector Pin Assignments (22-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 SATA_C_TXP0 O 3 SATA_C_TXN0 O 4 DGND - 5 SATA_C_RXN0 I 6 SATA_C_RXP0 I 7 DGND - 8 - - 9 - - 10 - - 11 DGND - 12 DGND - 13 DGND - 14 +V5S O 15 +V5S O 16 +V5S O 17 DGND - 18 - - 19 DGND - 20 - - 21 - - 22 - - C.
Appendices Apx. C Pin Assignments 29 DGND - 30 ICH_3A_ALERT_CLK I/O 31 PCIE_C_TXN_WLAN O 32 ICH_3A_ALERT_DAT I/O 33 PCIE_C_TXP_WLAN O 34 DGND - 35 DGND - 36 USB_P5N I/O 37 - - 38 USB_P5P I/O 39 - - 40 DGND - 41 - - 42 WIMAX_3G_LED# I 43 DGND - 44 - - 45 - - 46 - - 47 - - 48 +V1.5S O 49 - - 50 DGND - 51 PCI_3S_SERIRQ I 52 - - C.
Appendices Apx. C Pin Assignments Pin No. Signal Name I/O Pin No. Signal Name I/O 1 USB_VCC1 O 2 USB_L_P1N I/O 3 USB_L_P1P I/O 4 DGND - C.24 CN25 Table C-24 MB to Touch Pad Board Connector Pin Assignments (8-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 LID_SW#_3 O 2 +V3LA O 3 +V5S O 4 - - 5 IM_DAT_5 I/O 6 IM_CLK_5 I/O 7 TP_LED_ON O 8 DGND - C.
Appendices Apx. C Pin Assignments 3 C.28 USB_P8N CN29 Table C-28 4 I/O +V3S O Internal Speaker Right Connector (2-Pin) Internal Speaker Right Connector Pin Assignments (2-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 SPK_OUT_R+ O 2 SPK_OUT_R- O C.29 CN47 Table C-29 DDR2 DIMM0 Connector (200-Pin) DDR2 DIMM0 Connector Pin Assignments (200-Pin) Pin No. Signal Name I/O Pin No.
Appendices C-14 Apx.
Appendices Apx. C Pin Assignments 115 MA_CS1# O 116 MA_A(13) O 117 +V1.8 O 118 +V1.
Appendices Apx. C Pin Assignments 185 MA_DM(7) O 186 MA_DQS#(7) I/O 187 DGND - 188 MA_DQS(7) I/O 189 MA_DATA(58) I/O 190 DGND - 191 MA_DATA(59) I/O 192 MA_DATA(62) I/O 193 DGND - 194 MA_DATA(63) I/O 195 SB_3S_SMDATA I/O 196 DGND - 197 SB_3S_SMCLK I/O 198 N$860954 - 199 +V3S O 200 N$861284 - C.30 CN51 Table C-30 C-16 DDR2 DIMM1 Connector (200-Pin) DDR2 DIMM1 Connector Pin Assignments (200-Pin) Pin No. Signal Name I/O Pin No.
Appendices Apx.
Appendices C-18 Apx. C Pin Assignments 115 MB_CS1# O 116 MB_A(13) O 117 +V1.8 O 118 +V1.
Appendices Apx. C Pin Assignments 185 MB_DM(7) O 186 MB_DQS#(7) I/O 187 DGND - 188 MB_DQS(7) I/O 189 MB_DATA(58) I/O 190 DGND - 191 MB_DATA(59) I/O 192 MB_DATA(62) I/O 193 DGND - 194 MB_DATA(63) I/O 195 SB_3S_SMDATA I/O 196 DGND - 197 SB_3S_SMCLK I/O 198 N$860610 - 199 +V3S O 200 N$860611 - C.31 CN500 Table C-31 SIM Card Connector (6-Pin) SIM Card Connector Pin Assignments (6-Pin) Pin No. Signal Name I/O Pin No.
Appendices Apx. C Pin Assignments 5 C.34 DGND - JACK3 Table C-34 6 - - Head Phone Connector (6-Pin) Head Phone Connector Pin Assignments (6-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 HP_R_JACK O 3 HP_L_JACK O 4 HPS_JACK I 5 DGND - 6 - - CRT Board C.35 CN2000 Table C-35 CRT Board Connector Pin Assignments (15-Pin) Pin No. Signal Name I/O Pin No.
Appendices Apx. C Pin Assignments 11 G O 12 DGND - 13 R O 14 +V5S_RGB O 15 - - - - - FM Tuner Board C.37 CN2002 Table C-37 FM Antenna Connector (2-Pin) FM Antenna Connector Pin Assignments (2-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 FM_ANT I 2 DGND - C.38 CN2003 Table C-38 FM Tuner Board Connector (8-Pin) FM Tuner Board Connector Pin Assignments (8-Pin) Pin No. Signal Name I/O Pin No.
Appendices C.40 Apx. C Pin Assignments CN2005 Table C-40 C-22 Touch Pad Board Connector (8-Pin) Touch Pad Board Connector Pin Assignments (8-Pin) Pin No. Signal Name I/O Pin No.
Apx. D Keyboard Scan/Character Codes Apx. D Appendices Keyboard Scan/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan Codes (set 1 and set 2) (1/4) Cap Code set 1 Code set 2 Note No.
Appendices Apx. D Keyboard Scan/Character Codes Table D-1 Scan Codes (set 1 and set 2) (2/4) Cap D-2 Code set 1 Code set 2 Note No.
Apx. D Keyboard Scan/Character Codes Appendices Table D-1 Scan Codes (set 1 and set 2) (3/4) Cap Code set 1 Code set 2 Note No.
Appendices Apx. D Keyboard Scan/Character Codes Table D-1 Scan Codes (set 1 and set 2) (4/4) Cap Code set 1 Make Code set 2 Break Make Note No. Keytop Break 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 7 F0 7 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0 2F E0 F0 2F 205 Kat/Hir 70 F0 70 *8 206 Hen 79 F0 79 *8 207 Muh 7B F0 7B *8 Notes: 1. 2.
Apx. D Keyboard Scan/Character Codes Appendices Table D-2 Scan Codes with left Shift key Cap Key Code set 1 Code set 2 No.
Appendices Apx. D Keyboard Scan/Character Codes Table D-3 Scan Codes in Numlock mode Cap Key Code set 1 No.
Apx. D Keyboard Scan/Character Codes Appendices Table D-5 Scan Codes in overlay mode Cap No.
Appendices Apx. D Keyboard Scan/Character Codes Table D-7 No.126 key scan code Key top Pause Shift Code set 1 Code set 2 Make Make Common* E1 1D 45 E1 Ctrl* E0 C6 E0 46 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
Apx. E Key Layout Appendices Apx. E Appendix E E.1 Key Layout United States (US) Keyboard Figure E-1 United Status Keyboard E.
