R200 Portégé R200 PORTÉGÉ R200 PORTÉGÉ R200 PORTÉGÉ R200 PORTÉGÉ R200 PORTÉGÉ R200 PORTÉGÉ R200 Choose freedom. Choose freedom. computers.toshiba-europe.com computers.toshiba-europe.
Copyright © 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
EU Declaration of Conformity TOSHIBA declares, that the product TOSHIBA PORTÉGÉ R200 conforms to the following Standards: This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 89/336/EEC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 99/5/EC in case of implemented telecommunication accessories and the Low Volta
In the following environments the use of this product can be restricted: ■ Medical Environments: This product is not certified as a medical product according to the Medical Product Directive 93/42/EEC, but can be used in office areas where the use is not restricted. Please disable the wireless LAN or Bluetooth hardware in such areas as long this feature is not official supported by the operator of the related medical facility.
Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
PORTÉGÉ R200 Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii Keys . . . . . . . . . . . . . . . . . . .
Back side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Keyboard indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Region selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Properties menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Modem Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Battery indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 DC IN indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Power indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Formatting an SD memory card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Inserting an SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Removing an SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 SD card care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17 Before you call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17 Where to write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PORTÉGÉ R200 Preface Congratulations on your purchase of the PORTÉGÉ R200 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ R200 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, Finger print Sensor, USB floppy disk drive, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
PORTÉGÉ R200 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
PORTÉGÉ R200 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft® Windows XP Professional ■ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Microsoft® Windows XP Professional Microsoft Internet Explorer TOSHIBA Utilities TOSHIBA SD Memory Boot Utility TOSHIBA TouchPad On/Off Utility TOSHIBA Power Saver TOSHIBA Mobile Extension TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool TOSHIBA Controls TOSHIBA Password Utility Online manual Product Recovery Media Documentation ■ PORTÉGÉ R20
Introduction Processor Built-in The computer is equipped with an Intel® processor. Intel® Pentium® M processor, which incorporates a 2 MB level 2 cache memory. It also supports Enhanced Intel® SpeedStepTM technology. Disclaimer (CPU) Central Processing Unit (“CPU”) Performance Disclaimer.
Introduction Memory Slots 256, 512 or 1,024 MB memory modules can be installed on the main board for a maximum of 1,280 MB system memory. Disclaimer (General Main Memory Disclaimer) The graphics system in your computer may use part of the main system memory for graphics performance and therefore reduce the amount of system memory available for other computing activities.
Introduction AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. It encloses 2-pin or 3-pin plug type. Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer. Refer to the section in Chapter 2, The Grand Tour. Disks Hard disk drive Available in three sizes. ■ 30.0 billion bytes (27.
Introduction Disclaimer (LCD) Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. Screen will dim when the computer is operated on battery power and you will not be able to increase the brightness of the screen. Graphics controller Graphics controller maximizes display performance.
Introduction Universal Serial Bus (USB 2.0) The computer has Universal Serial Bus ports that comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard (The ports also support USB 1.1). After you have connected the Slim Port Replicator to the computer, be sure to connect the USB cable to the USB port of the Slim Port Replicator, instead of a USB port on the back side of the computer.
Introduction Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA, Canada, UK, France, Germany and Australia. Only V.90 is available in other regions.
Introduction Wireless LAN Some models in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision B or G), and Turbo Mode. Theoretical maximum speed: 54Mbps (IEEE 802.11g) ■ Theoretical maximum speed: 11Mbps (IEEE802.11b) ■ Theoretical maximum speed: 108Mbps (Turbo Mode) ■ Frequency Channel Selection (2.
Introduction Disclaimer (Wireless LAN/Atheros) The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. [54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed.
Introduction HDD automatic power off This feature automatically cuts off power to the hard disk drive when it is not accessed for a time specified. Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver. System automatic Standby/Hibernation This feature automatically shuts down the system in standby mode or Hibernation mode when there is no input or hardware access for a time specified.
Introduction Heat dispersal HDD Protection To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. ■ Maximum Performance Turns on fan first, then if necessary lowers CPU processing speed. ■ Performance Uses a combination of fan and lowering the CPU processing speed.
Introduction Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Power Saver To access this power savings management program, click start, click Control Panel, click Performance and Maintenance and select the TOSHIBA Power Saver icon.
Introduction Bluetooth Stack for Windows by Toshiba This software enables communication between remote Bluetooth devices. Bluetooth cannot be used in models that do not have a Bluetooth module installed. TOSHIBA SD Memory Boot Utility The TOSHIBA SD memory boot utility is a utility which can create SD memory card to a boot disk. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows.
Introduction TOSHIBA Accessibility This utility lets you make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. The Fn key remains active until another key is pressed. TOSHIBA Hotkey Utility for Display Devices This utility has the change of a display device, and the function to change display resolution. Press Fn + F5 to change the active display device. Press Fn + Space keys to change the display resolution.
Introduction ■ When a Slim Port Replicator is connected to the computer, you can not use the following computer's ports: LAN jack, DC IN 15V jack, External monitor port, USB port. ■ The LAN jack of the Slim Port Replicator supports Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T) is not supported.
PORTÉGÉ R200 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Disclaimer (Non-applicable Icons) Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
The Grand Tour Left side The following figure shows the computer’s left side. Cooling vents Headphone jack SD card slot Volume control The left side of the computer Cooling vents Cooling vents help CPU keep from overheating. Do not block the cooling vents. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury. Headphone jack A 3.
The Grand Tour Right side The following figure shows the computer’s right side. Wireless communication switch PC card eject button infrared port PC card slot Security lock slot The right side of the computer PC card slot The PC card slot can accommodate a Type II card. The slot supports 16-bit PC cards and CardBus PC cards. PC card eject button This is a button for taking out PC card from a PC card slot. Keep foreign objects out of the PC card slot.
The Grand Tour Infrared port This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.15 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices. Security lock slot A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft. Back side The following figure shows the computer’s back side.
The Grand Tour LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). The LAN has two indicators. Refer to Chapter 4, Operating Basics, for details. The LAN jack of the Slim Port Replicator supports Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX).
The Grand Tour Keep foreign objects out of the USB connectors. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury. ■ After you have connected the Slim Port Replicator to the computer, be sure to connect the USB cable to the USB port of the Slim Port Replicator, instead of a USB port on the back side of the computer.
The Grand Tour Battery release latch Slide and hold this latch to release the battery pack for removal. For detailed information on removing the battery packs, refer to Chapter 6, Power and Power-Up Modes. Docking port Use this port to connect an optional Slim Port Replicator or High Capacity 2nd Battery Pack. Keep foreign objects out of the docking port. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard.
The Grand Tour Front with the display open This section shows the front of the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the LCD display panel lift up. Position the LCD display panel at a comfortable viewing angle.
The Grand Tour LCD screen The LCD screen displays high-contrast text and graphics. The computer’s XGA screen consists of 1024 × 768 pixels. Refer to Display Controller and Modes in Appendix B. When the computer operates on the AC adaptor the LCD screen’s image will be somewhat brighter than when it operates on battery power. The lower brightness level is intended to save battery power.
The Grand Tour TOSHIBA Presentation button Press this button to change internal display, simultaneous display, or multi-monitor display. The default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768. When you press this button twice, the display mode returns to single display on LCD only. Setting of multi-monitor display in Windows XP, computer changes its display mode to the multimonitor display on LCD and CRT.
The Grand Tour DC IN The DC IN indicator glows in blue when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Battery The Battery indicator shows the condition of the battery’s charge: Blue indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge. Refer to Chapter 6, Power and Power-Up Modes.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers. When the Caps Lock indicator glows the keyboard is in all-caps mode. Caps Lock indicator Caps Lock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase.
The Grand Tour USB floppy disk drive USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks. It connects to the USB port. Option or provided with some models. USB connector Disk-In-Use Indicator Floppy disk slot Eject button USB floppy disk drive USB connector Insert this connector to the USB port of your computer. Disk-In-Use Indicator This indicator lights when the floppy disk is being accessed. Floppy disk slot Insert a floppy disk in this slot.
The Grand Tour High Capacity 2nd Battery Pack A High Capacity 2nd Battery Pack can increase your battery operating time.(Option or provided with some models).A High Capacity 2nd Battery Pack is seated in a base that fits beneath the computer. Refer to the Replacing the battery pack section in Chapter 6, The Power and Power-Up Modes. Always use the High Capacity 2nd Battery Pack supplied as an accessory or an equivalent High Capacity 2nd Battery Pack specified in the User's Manual.
The Grand Tour The AC adaptor (3-pin plug) ■ The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model. Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled. ■ Do not use a 3-pin to 2-pin conversion plug. ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.
PORTÉGÉ R200 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space – for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Select a work area that has: ■ a well-designed and functioning ventilation system that does not forcefully direct air on you ■ good air circulation ■ a comfortable ambient temperature and relative humidity.
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location. Your PC may fall, causing damage to the PC or possibly injury. ■ Never leave the power to your PC on continuously for more than 24 hours. Turn the power off when this product is not in use.
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Posture and positioning of the computer ■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to the floor. ■ Keep head level, or bent slightly forward, forward facing, and balanced. Generally the head is in-line with the torso.
Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user.
Getting Started Strategic Rest Breaks Take short, strategically spaced rest breaks to avoid eye strain and body discomforts. For more specific recommendations on the safety and comfort of your computer environment, customers in the United States may visit the United States Department of Labor, Occupational Safety & Health Administration website at: http://www.osha.gov/SLTC/etools/computerworkstations/ Other Things to Note ■ Never turn off the power while an application is running.
Getting Started ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury. ■ Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible.
Getting Started Connecting the power cord to the AC adaptor (3-pin plug) The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model. Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet.
Getting Started Opening the display The computer’s LCD display panel can be rotated in a wide range of angles for optimal viewing. 1. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly. Adjust the angle of the panel to provide optimal clarity. As the display panel cannot be opened until 180 degrees, please be careful of the angle when flipping open the display panel. Use reasonable care when opening and closing the LCD display panel.
Getting Started 1. Open the computer’s LCD display panel. 2. Press and hold the computer’s power button for two or three seconds. Power button Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully.
Getting Started Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The hibernation feature does not save the status of peripheral devices. ■ Save your data. While entering hibernation mode, the computer saves the contents of memory to the HDD.
Getting Started Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below. 1. Click start and open the Control Panel. 2. Open Performance and Maintenance and open Power Options. 3. Select the Hibernate window in the Power Options Properties, select the Enable hibernation check box and click the Apply button. 4. Open TOSHIBA Power Saver. 5.
Getting Started ■ Before entering Standby mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in standby mode. The computer or the module could be damaged. ■ Do not remove the battery pack while the computer is in standby mode (unless the computer is connected to an AC power source). Data in memory will be lost.
Getting Started Standby limitations Standby will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise. Restarting the computer Certain conditions require that you reset the system. For example, if: ■ You change certain computer settings. ■ An error occurs and the computer does not respond to your keyboard commands. ■ There are three ways to reset the computer system: 1.
Getting Started 3. Use the up or down cursor key to select the CD-ROM/DVD drive in the display menu. For details, refer to the Boot priority section in Chapter 7, HW Setup. 4. Follow the on-screen instructions. Restoring TOSHIBA utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD) contains drivers and applications, which are included with your computer system.
PORTÉGÉ R200 Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the USB floppy disk drive (optional in some models), Sound System, Modem, Wireless communication features and LAN. It also provides tips on care of the computer and floppy disks. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
Operating Basics Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition. ■ Wash and dry your hands thoroughly. ■ Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially during dry seasons such as winter. ■ Clean the sensor with a lint-free cloth.
Operating Basics We will put some drawings like these illustrations to explain the right way of finger sliding. Align the finger and sensor like the drawings. Points to note about the Fingerprint Utility The user should back up the user profile information when using the functions provided in this software to encrypt files or folders. If this software or the user information is deleted without backing up the user profile information, the encrypted files will no longer be accessible.
Operating Basics Set Up Procedure Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required authentication data using the "OmniPass Enrollment Wizard". The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration. 1. Click start, Point to All Programs, point to Softex and click OmniPass Enrollment Wizard. 2. Click Enroll. 3.
Operating Basics 8. Click Yes when the following message appears: "OmniPass has successfully created the new user. Would you like OmniPass to log on the new user? Once logged on, passwords can be remembered for the new user." This completes the fingerprint registration process. Window Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows.
Operating Basics ■ Avoid swiping with the finger stiff or pressed-on too hard Fingerprint reading may fail if the center of the fingerprint is not touching on the sensor, or when finger is swiped while pressing hard. Make sure that the center of the fingerprint is touching the sensor before swiping. ■ Confirm the center of the fingerprint whirl before swiping The thumb's fingerprint has a bigger whirl, which is prone to misalignment and distortions.
Operating Basics If you connect the USB floppy disk drive after turning on the computer, it will take about 10 seconds for the computer to recognize the drive. Do not disconnect and reconnect before 10 seconds has elapsed. Disconnecting USB floppy disk drive When you have finished using the USB floppy disk drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped.
Operating Basics 8. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface. 9. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields. Sound System Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications.
Operating Basics The Noise Reduction enhancement helps to eliminate ambient noise from the voice input signal to provide a clean and clear signal to applications. This feature can be used with any microphone. The audio controller can be powered down when the audio function is idle. To enable the Audio Power Management, follow the steps below. 1. Click the Power Management tab. 2. Select the Normal Power Savings in the Power Mode pull-down list.
Operating Basics To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. If you change the Country/ Region in the Control Panel, the change may not take effect. 2. The Region Selection icon will appear in the Windows Task Bar. 3.
Operating Basics Dialing Properties Select this item to display the dialing properties. If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the modular cable(optional), follow the steps below. The modular cable for connecting a modem should use a commercially available cable. Connect the end of the modular cable with the core to the computer.
Operating Basics If you use a storage device such as an optical drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: ■ Modem speed is slow or communication is interrupted. ■ Skips may occur in sound. Disconnecting To disconnect the internal modular cable(optional), follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner.
Operating Basics ■ The numerical values for display are the theoretical maximums for Wireless LAN standards. The actual values may differ. ■ The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The Transmit Rate (at X Mbit/s) is the theoretical maximum speed under the IEEE802.11 (b/g) standard.
Operating Basics BluetoothTM Stack for Windows® by TOSHIBA Please note that this software is specifically designed for the following operating systems: ■ Microsoft® Windows® 2000 Professional ■ Microsoft® Windows® XP Detailed information regarding the use with these operating systems is listed below. Please refer also to the electronic information which is included with each software. This BluetoothTM Stack is based on BluetoothTM Version 1.1/1.2/2.0+EDR specification.
Operating Basics ■ Do not use the WiFi or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt WiFi or Bluetooth operation. ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury.
Operating Basics LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Some models are equippend with a Gigabit Ethernet LAN. This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. ■ The Wake-up on LAN function consumes power even when the system is off.
Operating Basics 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. LAN jack LAN connector Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN Active indicator glows orange.
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Before moving the computer, it recommends changing the function of HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter. ■ Make sure all disk activity has ended before moving the computer. Check the HDD indicator on the computer. ■ Turn off the power to the computer.
Operating Basics Using the Hard Disk Drive (HDD) Protection There is a function for reducing the risk of damage on HDD in this computer. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks and similar signs in the computer, and automatically moves the HDD head to a safe position in order to reduce the risk of damage that could be caused by a head-to-disk contact. This function does not guarantee that the HDD will not be damaged.
Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start point to All Programs point to TOSHIBA point to Utilities and click HDD Protection setting. The window can also be started from the icon on the Taskbar, or from the Control Panel. HDD Protection You can choose whether to enable or disable HDD Protection. Detection Level This function can be set to four levels.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.
PORTÉGÉ R200 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the upper surface become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key or press the Touch Pad. Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data.
The Keyboard Display selection: Press Fn + F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to the internal LCD. Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD screen brightness in decrements.
The Keyboard Touch Pad: Pressing Fn + F9 in a windows environment enables or disables the Touch Pad function. When you press these hot keys, the current setting will change and be displayed as an icon. LCD screen resolution selection: Press Fn + Space keys to change the LCD screen resolution. Each time when you press these hot keys, the LCD screen resolution changes as follows: With XGA, you can change the resolution between 800 × 600 and 1024 × 768 pixels.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys shown in the figure below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
PORTÉGÉ R200 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power conditions continued AC adaptor connected AC adaptor not connected Power on Power off (no operation) 2nd battery fully charged • Operates • No charge • LED: 2nd Battery blue DC IN blue • No charge • LED: 2nd battery blue DC IN blue 2nd Battery partially charged or no charge • Operates • Charge*2 • LED: 2nd battery orange DC IN blue • Quick charge*2 • LED: 2nd battery orange DC IN blue No 2nd battery installed • Operates • No charge • LED: 2nd battery off DC IN blue
Power and Power-Up Modes Power conditions continued Power on AC adaptor not connected 2nd battery charge is above low battery trigger point • Operates • LED: 2nd battery off DC IN off 2nd battery charge is below low battery trigger point • Operates • LED: 2nd battery flashes orange DC IN off 2nd battery charge is exhausted Computer shuts down *3 No 2nd battery is installed • No operation *5 • LED: 2nd battery off DC IN off Power off (no operation) 2nd battery indicator refers to the Secondary bat
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the battery pack. The following indicator lights indicate the battery status: Flashing orange The battery charge is low. The AC adaptor must be connected to recharge the battery.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Blue Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates power is being supplied to the computer while the computer is in Standby mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power through an AC adaptor for an extended period, more than a month, the battery may fail to retain a charge.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of battery packs can cause death, serious injury or property damage.
Power and Power-Up Modes 7. Never allow a battery pack to become wet. A wet battery pack will overheat or ignite causing rupture or fire, possibly resulting in death or serious injury. 8. Never store a battery pack in an area of high humidity. This could cause a fire or explosion possibly resulting in serious injury. 9. Never expose a battery pack to abnormal shock, vibration or pressure.
Power and Power-Up Modes 14. Always dispose of used battery packs in compliance with all applicable laws and regulations. Put insulating tape, such as cellophane tape, on the electrode during transportation to avoid a possible short circuit, fire or electric shock. Failure to do so could possibly result in serious injury. 15. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.
Power and Power-Up Modes 3. After the battery pack is charged, avoid leaving the AC adaptor connected and the computer turned off for more than a few hours at a time. Continuing to charge a fully-charged battery pack can damage the battery. Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain.
Power and Power-Up Modes The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer. If you make heavy use of external devices, for example, the battery might scarcely charge at all during operation. Refer also to the section Maximizing battery operating time. Battery charging notice The battery may not charge right away under the following conditions: ■ The battery is extremely hot or cold.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored in TOSHIBA Power Saver. ■ Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type State and Retention Time Battery pack (3800mAh) about 6 days (Standby mode) about 90 days (Power off) High Capacity 2nd Battery Pack (3900mAh) about 12 days (Standby mode) about 180 days (Power off) RTC battery 30 days * Time of the High Capacity 2nd Battery Pack is the time which united
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. Battery pack is the expendables. Life runs out by doing repetition charge. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps below. Do not touch the battery release latch while holding the computer. Or you may get injured by the dropped battery pack by unintentional release of the battery release latch. 1. 2. 3. 4. Turn the computer’s power off. Disconnect all cables connected to the computer. Close the LCD display panel and turn the computer upside down. Insert the battery pack. Battery pack Securing the battery cover 5.
Power and Power-Up Modes High Capacity 2nd Battery Pack A High Capacity 2nd Battery Pack can increase the battery-based operating time of the computer. To increase the battery-based operating time, connect the High Capacity 2nd Battery Pack to the computer. This section explains the installation and removal of the High Capacity 2nd Battery Pack. Before you connect the High Capacity 2nd Battery Pack, make sure you turn off the computer and disconnect the AC Adaptor and any other external devices.
Power and Power-Up Modes Securing the latches 6. Return your computer to the upright position. Disconnecting the High Capacity 2nd Battery Pack Follow the steps below to disconnect a High Capacity 2nd Battery Pack. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4. Close the LCD display panel and turn the computer upside down. 5. Open the latches in the direction of the arrows. Releasing the latches 6.
Power and Power-Up Modes Removing the High Capacity 2nd Battery Pack TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: start -> All Programs -> TOSHIBA -> Utilities ->Password Utility The user password dialog box contains two main fields: User Password and User Token.
Power and Power-Up Modes ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy disk or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place. ■ When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or copy-and-paste the character string.
Power and Power-Up Modes Supervisor password If you set a supervisor password, some functions might be restricted when a user logs on with the user password. To set a supervisor password, execute the file TOSPU.EXE. The file is located at: C:\Program Files\Toshiba\Windows Utilities\SVPWTool\TOSPU.EXE This utility lets you do the following: ■ Register, delete or change the supervisor password. ■ Create or invalidate a supervisor password token.
Power and Power-Up Modes Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk. ■ Standby: Data is maintained in the computer’s memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver.
PORTÉGÉ R200 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to setup of Execute-Disable Bit Capability and TPM is explained. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Returns all HW Setup values to the factory settings. About Displays the HW Setup version. Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you use the display to be used when the computer is booted.
HW Setup HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive*1, CD-ROM*2 and LAN (Default). CD-ROM −> LAN −> HDD −> FDD The computer looks for bootable files in the following order: CD-ROM*2, LAN, HDD, floppy disk drive*1. CD-ROM −> LAN −> FDD −> HDD The computer looks for bootable files in the following order: CD-ROM*2, LAN, floppy disk drive*1 and HDD.
HW Setup 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. ■ If a supervisor password is set only it is the following. ■ The menu above appear (able to run HW Setup). ■ The menu above does not appear (unable to run HW Setup). ■ If the supervisor and user password are set, it is the following. ■ The menu above appears when you use the supervisor and user password to start the computer (able to run HW Setup).
HW Setup CPU This function lets you set the CPU operating mode. It is displayed in Pentium-M® model only. Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary (Default). Always High CPU power consumption and clock speed automatic switching function is disabled.
HW Setup Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Operating system sets devices that it can control (Default). PCI Express Link ASPM This feature lets you set the PCI Express power-saving configuration. Enabled Enables power-saving when the PCI Express device is not being used. Disabled Disables power-saving for performance.
HW Setup HDD Set the type of the USB memory to be equivalent to the HDD (Default). * Based on the [HDD] order in the [Boot Priority Options] item. The order with respect to the other HDD can be set in the [HDD Priority Options] item. FDD Set the type of the USB memory to be equivalent to the FDD. * Based on the [FDD] order in the [Boot Priority Options] item.
HW Setup Starting and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Switch on your computer while pressing the Esc key. If “Password =” is displayed, enter the user password and press the Enter key. Please refer to Chapter 6, the TOSHIBA Password Utility, for details about the user password. The “Check system. Then press [F1] key.” message is displayed. 2. Press the F1 key. The BIOS setup program will start up.
HW Setup System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. Security controller The security controller settings are available in SYSTEM SETUP (2/2). TPM This setting enables or disables the security controller known as TPM (Trusted Platform Module). Enabled Enables the TPM. Disabled Disables the TPM (Default).
PORTÉGÉ R200 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC card The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not pop out. Be sure to push the PC card firmly and press the eject button again. 4. Press the extended eject button to pop the card out slightly. 5. Grasp the PC card and draw it out.
Optional Devices Formatting an SD memory card SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format. In order to run TOSHIBA SD memory card format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.
Optional Devices 4. Grasp the SD card and remove it. SD card slot SD card Removing an SD card ■ Make sure the SD card indicator is out before you remove the SD card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. ■ Do not remove an SD card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the SD card could be lost.
Optional Devices Memory expansion This computer has equipped the underside one memory module slot. You can increase the capacity of RAM by installing an additional memory or replacing default memories with additional memories. ■ Place a mat beneath the computer to prevent making a scratch on the lid when replacing the memory module. Avoid the mat that generates static electricity. ■ When you remove a memory, please do not touch other portions of a computer. ■ Use only memory modules approved by TOSHIBA.
Optional Devices 4. Loose a screw securing the memory module cover. The screw is attached to the cover to prevent it from being lost. 5. Slide your fingernail or a thin object under the cover and lift it off. Screw Memory module cover Removing the memory module cover 6. Fit the memory module’s connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place.
Optional Devices 7. Seat the memory module cover and secure it with one screw. Be sure that the cover is closed firmly. Seating the memory module cover 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details. 9. Return your computer to the upright position. 10. Turn the computer power on and make sure the added memory is recognized. Click start, click Control Panel, click Performance and Maintenance and select the System icon.
Optional Devices 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Latches Removing the memory module 8. Seat the memory module cover and secure it with one screw. 9.
Optional Devices 3. Connect an AC Adaptor to the Slim Port Replicator. ■ You cannot use a High Capacity 2nd Battery Pack to power a Slim Port Replicator. ■ You must connect the High Capacity 2nd Battery Pack and an AC adaptor to the Slim Port Replicator to charge the High Capacity 2nd Battery Pack. AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load.
Optional Devices 2. Connect the monitor cable to the external monitor port. External monitor port Monitor cable Connecting the monitor cable to the external monitor port 3. Turn the monitor’s power on. 4. Turn the computer’s power on. When you turn on the power, the computer automatically recognizes the monitor and determines whether it is colour or monochrome.
Optional Devices The following ports and accessories are available on the Slim Port Replicator. ■ One RJ45 LAN jack ■ External monitor port ■ DC IN 15V jack ■ Universal Serial Bus ports (four) ■ Port to charge a High Capacity 2nd Battery Pack Security lock Security locks enable you to anchor your computer and optional Slim Port Replicator to a desk or other heavy object to help prevent unauthorized removal of the computer or Slim Port Replicator. The computer has a security lock slot on the right side.
PORTÉGÉ R200 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the OS documentation.
Troubleshooting S In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■ The computer stops and does not proceed to display information or messages except the TOSHIBA logo.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow blue) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated. Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes.
Troubleshooting Password Problem Procedure Cannot enter password Refer to the TOSHIBA Password Utility section in Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again.
Troubleshooting Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a floppy disk is in the floppy disk drive or a CD-ROM is in the optical media drive. Remove any floppy disk and/or CD-ROM and check Boot priority. Refer to the Boot Priority section in Chapter 7, HW Setup. There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented.
Troubleshooting Problem Procedure You cannot read a file Make sure the target file is on the SD memory card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer.
Troubleshooting Problem Procedure Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Buttons tab. 3. Set the double-click speed as instructed and click OK. The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1.
Troubleshooting Fingerprint Sensor Problem Procedure Reading of the fingerprint was not successful. Please try again using the correct posture. Refer to Using the Fingerprint Sensor in Chapter 4, Operating Basics. Please try reading the fingerprint again using another enrolled finger. The fingerprint cannot be read due to injuries to the finger. Please try reading the fingerprint using another enrolled finger.
Troubleshooting USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
Troubleshooting Sound System Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Troubleshooting Modem Problem Procedure Communication software can’t initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Properties in the Control Panel. You can hear a dial tone but can’t make a call If the call is going through a PBX machine, make sure the communication application’s tone dial detection feature is disabled. You place a call, but a connection can’t be made Make sure the settings are correct in your communications application.
Troubleshooting LAN Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator. Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator.
Troubleshooting Disposing of PC and PC batteries ■ Discard this PC in accordance with ordinances or rules of local regulations. For further information, contact your local government. ■ This PC contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulation, it may be illegal to dispose of old batteries by placing them in the trash. ■ Please be kind to our shared environment.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
PORTÉGÉ R200 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 286 (w) × 229 (d) × 9.9/19.8 (h) millimeters (not including parts that extend beyond the main body) Refer to User’s Manual or Information sheet about Weight.
Specifications Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) Communication speed PORTÉGÉ R200 Full duplex Half duplex V.21/V.22/V.22bis/V.32 /V.32bis/V.34/V.90 103/212A V.17/V.29/V.
Specifications Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedance 600 ohms ±30% Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.
PORTÉGÉ R200 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The display controller supports VGA, SVGA and XGA modes at internal LCD display panel. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 64K mode.
Display Controller and Modes Table1 Video modes (VGA) Video mode Type Resolution Character matrix (pels) LCD colours CRT colours Scanning frequency Vertical (Hz) 0, 1 VGA Text 40 × 25 Characters 8×8 16 of 256K 16 of 256K 70 2, 3 VGA Text 80 × 25 Characters 8×8 16 of 256K 16 of 256K 70 0*, 1* VGA Text 40 × 25 Characters 8 × 14 16 of 256K 16 of 256K 70 2*, 3* VGA Text 80 × 25 Characters 8 × 14 16 of 256K 16 of 256K 70 0+, 1+ VGA Text 40 × 25 Characters 9 × 16 16 of 256K
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type LCD colours CRT colours Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 16 of 256K 70 11 VGA Grph 640 × 480 Pels 8 × 16 2 of 256K 2 of 256K 60 12 VGA Grph 640 × 480 Pels 8 × 16 16 of 256K 16 of 256K
Display Controller and Modes Table 2 Video modes Resolution LCD colours CRT colours Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K 256/256K 60 75 85 100 1600 × 1200 256/256K 256/256K 60 75 85 100 1920 × 1440 (CRT only) – 256/256K 60 75 85 2048 × 1536 (CRT only) – 256/256K 60 75 * Max resolution for LCD is limited upto 1600 × 1200 mode.
Display Controller and Modes Table 2 Video modes continued Resolution LCD colours CRT colours Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K 64K/64K 60 75 85 100 1600 × 1200 64K/64K 64K/64K 60 75 85 100 1920 × 1440 (CRT only) – 64K/64K 60 75 85 2048 × 1536 (CRT only) – 64K/64K 60 75 * Max resolution for LCD is limited upto 1600 × 1200 mode.
Display Controller and Modes Table 2 Video modes continued Resolution LCD colours CRT colours Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M 16M/16M 60 75 85 100 1600 × 1200 16M/16M 16M/16M 60 75 85 100 1920 × 1440 (CRT only) – 16M/16M 60 75 85 2048 × 1536 (CRT only) – 16M/16M 60 75 * Max resolution for LCD is limited upto 1600 × 1200 mode.
Display Controller and Modes Display settings 1. You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display. *The [Settings] tab is displayed in the following steps; 1) Open [Control Panel], click [Appearance and Themes]. 2) Click [display]. 3) Select [Settings] tab. ■ The way to move to multi-monitor 1) Press [Ctrl] + [Alt] + [F12] keys to make. [Intel(R) 82852/82855 GM/GME Graphics Controller Prope...
PORTÉGÉ R200 Appendix C Wireless LAN Card Specifications Form Factor Mini PCI Type III Compatibility ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. Network Operating System ■ Microsoft Windows® Networking Media Access Protocol ■ CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) Data Rate ■ Theoretical maximum speed: 54Mbps (IEEE802.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID*2 2400-2483.5 MHz 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457*1 11 2462 12 2467 13 2472 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used.
Wireless LAN Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 2400-2483.5 MHz Note 6 2437 US only *3 *3 Available Area: US (USA, CANADA) only.
PORTÉGÉ R200 Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S.
PORTÉGÉ R200 Appendix E If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. PORTÉGÉ R200) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
PORTÉGÉ R200 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output SXGA+: super extended graphics
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
Glossary escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F.
Glossary J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer.
Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.
Glossary P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even.
Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT. RJ11: A modular telephone jack. RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation.
Glossary T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
PORTÉGÉ R200 Index A AC adaptor 1-5 additional 1-15, 8-12 connecting 3-6 DC IN 15V jack 2-5 ASCII characters 5-9 B Battery charging 6-10 extending life 6-13 indicator 2-11, 6-4 location 2-6 monitoring capacity 6-12 real time clock 1-5, 6-6 safety precautions 6-7 save mode 1-11 types 6-5 Battery pack 1-4, 2-6 additional 8-11 replacing 6-14 Bluetooth 1-8, 4-14 Bluetooth Stack for Windows by Toshiba 1-14 problems 9-16 Boot Priority 7-2 C Cleaning the computer 4-18 Cooling vents 2-2 D DC IN indicator 2-11,
Index Fn + F3 (Standby) 5-4 Fn + F4 (Hibernation) 5-4 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-5 Fn + F7 (display brightness) 5-5 Fn + F8 (wireless setting) 5-5 Fn + F9 (Touch Pad) 5-6 Fn + Space (LCD screen resolution selection) 5-6 Fn-esse 1-13 Function keys 5-2 G Graphics controller 1-6 H Hard disk drive 1-5 automatic power off 1-10 HDD indicator 2-11 HDD Protection 4-20 Heat dispersal 1-11, 4-23 Hibernation 1-12, 5-4 Hot keys 1-10 display brightness decrease 5-5 display brightne
Index Memory 1-4 expansion 1-15, 8-8 installing 8-8 problems 9-13 removing 8-10 Modem 1-8, 4-10 connecting 4-12 disconnecting 4-13 problems 9-15 properties menu 4-11 region selection 4-10 Monitor external 1-6, 2-5, 8-12 problems 9-14 Moving the computer 4-19 P Password power on 1-10 problems 9-7 starting the computer by 6-21 Supervisor 6-20 user 6-19 PC card 1-7, 8-2 inserting 8-2 problems 9-9 removing 8-3 Pointing Device 1-6 problems 9-10 Touch Pad 1-6, 2-9 Touch Pad control buttons 2-9 Touch Pad locatio
Index R Recovery HDD 3-15 Recovery Media 3-16 Restarting the computer 3-14 S SD card 1-7, 8-4 care 8-7 indicator 2-11 inserting 8-6 problems 9-9 removing 8-6 Security lock 1-15 attaching 8-14 Slim Port Replicator 1-15, 8-13 Soft keys enhanced keyboard 5-2 Enter 5-3 right Ctrl key 5-3 ScrLock 5-3 Sound System 4-9 headphone jack 1-7, 2-2 microphone 4-9 mute hot keys 5-3 problems 9-14 speaker 2-7 volume control 2-2 Standby 1-12 setting 3-12 System automatic 1-10 T TOSHIBA Assist button 1-10 TOSHIBA Config
