User's Manual Z10t-A/WT310
Table of Contents Chapter 1 TOSHIBA Legal, Regulatory and Safety Copyright, Disclaimer and Trademarks .............................................. 1-1 Regulatory Information ......................................................................... 1-2 Video Standard Notice .......................................................................... 1-7 OpenSSL Toolkit License Issues ......................................................... 1-7 FreeType License Issues .......................................
Sound System and Video mode ......................................................... 4-30 Chapter 5 Utilities and Advanced Usage Utilities and Applications ...................................................................... 5-1 Special features ..................................................................................... 5-5 TOSHIBA Password Utility ................................................................... 5-7 TOSHIBA System Settings ...................................................
Chapter 1 TOSHIBA Legal, Regulatory and Safety This chapter states the legal, regulatory and safety information applicable to TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2013 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC. sMedio and sMedio TrueLink+ are trademarks or registered trademarks of sMedio, Inc. Secure Digital and SD are trademarks of SD Card Association.
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s HDMI(micro) port, Universal Serial Bus (USB 3.0) port as well as the Universal Serial Bus (USB 2.0) port, HDMI port and External RGB monitor port on the TOSHIBA Keyboard Dock.
Equipment and Telecommunications Terminal Directive 1999/5/EC, Ecodesign Directive 2009/125/EC (ErP) and the related implementing measures. This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented.
Canadian regulatory information (Canada only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment.
Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste. If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006/66/ EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
Battery is a consumption product, since the battery time depends on the usage of your computer. If the battery can not be charged at all, then it is a defect or failure. The changes in battery time is not a defect or failure. Following information is only for India: The use of this symbol indicates that this product may not be treated as household waste.
-----------------------/*===================================================== Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. 2. 3. 4. 5. 6. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
---------------------------------/* Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to use the following text: """ Portions of this software are copyright (C) The FreeType Project (www.freetype.org). All rights reserved. """ Please replace with the value from the FreeType version you actually use. Legal Terms ============ 0.
source and object code forms) and derivative works thereof for any purpose; and to authorize others to exercise some or all of the rights granted herein, subject to the following conditions: Redistribution of source code must retain this license file (`FTL.TXT') unaltered; any additions, deletions or changes to the original files must be clearly indicated in accompanying documentation. The copyright notices of the unaltered, original files must be preserved in all copies of source files.
ENERGY STAR® Program Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
Provide adequate ventilation Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep Mode). In this condition, observe the following: Never cover your computer or AC adaptor with any object. Never place your computer or AC adaptor near a heat source, such as an electric blanket or heater.
Heat injury Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
Turn off (shut down) the computer. Disconnect the AC adaptor and all peripherals before moving the computer (The keyboard dock, however, can be moved when connected). Close the display panel (not applicable in tablet mode). Do not pick up the computer by its display panel. Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury.
Please read. A note is a hint or advice that helps you make best use of your equipment.
Chapter 2 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Series Model Name Z10t-A WT310 Operating Mode Supported Laptop mode: when TOSHIBA Keyboard Dock is docked Tablet mode: when TOSHIBA Keyboard Dock is undocked Tablet mode only Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. SSD or Solid State Drive User's Manual This computer is equipped with a Solid State Drive (SSD). Click Tap the Touch Pad or click the left Touch Pad control button once (laptop mode). Left-click the mouse once.
Start screen You can go back to the Start screen from an app or the desktop by the following ways: Click the Start charm. Move the mouse pointer all the way into the lower-left corner of the screen and then click ). the Start button ( Press the Windows® logo key ( ) on the keyboard dock or the Windows button ( ) on the computer. For detailed information, please refer to the Windows Help and Support. Apps view You can find all of your apps including desktop programs in the Apps view.
Before you install a device or application, save any data in memory to the Solid State Drive or other storage media. Failure to do so may result in the loss of data. Connecting TOSHIBA Keyboard Dock The TOSHIBA Keyboard Dock provided with some models can turn your computer into a laptop for extensibility including a physical keyboard and more ports. To use the computer in laptop mode, you need to connect the TOSHIBA Keyboard Dock to the computer by following the steps below: 1. 2. 3.
Figure 2-2 Opening the computer body 1 1. Computer body Product appearance depends on the model you purchased. Use reasonable care when opening and closing computer body. Opening it vigorously or slamming it shut could damage the computer. Be careful not to open the computer body too far as this could put stress on the hinges and cause damage. Please close the computer body when you move or are carrying the computer. Do not lift the computer by the palm rest on the keyboard dock.
1. 2. 3. Disconnect and remove all peripheral devices and cables connected to the computer. Press the Eject button on the keyboard dock and make sure that the icon( ) is disappeared from the taskbar or that “Eject Docking Station” is no longer in the pop-up menu after clicking this icon. Slide and hold the Release latch to the left (unlock position) and then slowly lift the computer to release it from the computer holder and completely off the keyboard dock (a, b).
Never plug the AC adaptor into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury. Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.
Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack. Figure 2-6 Connecting the DC output plug to the computer (laptop mode) 2 1 1. DC IN 19V jack 2. DC output plug Computer appearance depends on the model you purchased. Figure 2-7 Connecting the DC output plug to the computer (tablet mode) 1 2 1. DC IN 19V jack 2. DC output plug Computer appearance depends on the model you purchased. 3.
After you turn on the power for the first time, do not turn it off until you have set up the operating system. Volume cannot be adjusted during Windows Setup. 1. Press the computer's power button. Figure 2-8 Turning on the power (laptop mode) 1 1. Power button Computer appearance depends on the model you purchased. Figure 2-9 Turning on the power (tablet mode) 1 1. Power button Computer appearance depends on the model you purchased.
Getting to know Windows For detailed information on what is new and how to operate Windows, please refer to the Windows Help and Support. Start screen The Start screen is the launching pad for everything you can do in the Windows operating system, providing new and easy ways to access everything from your favorite apps and Web sites to your contacts and other important information. From the Start screen, you can just start typing to search for what you want.
Windows Store Although many applications will be pre-installed or built-in to your computer, you will also have the ability to download many other applications at the click of your mouse. In the Windows Store you can search for and browse thousands of apps, all grouped into easy to find categories. Sign-in options Windows offers a number of sign-in options including Password( PIN( ) and Picture password( ), ) authentication to prevent from unauthorized access.
Do not turn the computer or peripheral devices back on immediately - wait a short period to avoid any potential damage. Restarting the computer Certain conditions require that you reset the computer, for example if: You change certain computer settings. If you need to restart the computer, there are two ways this can be achieved: In the Settings charm, click Power and then select Restart.
To restore the operation of the computer from Sleep Mode, press the power button or any key on the keyboard dock for a short amount of time. Please note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the TOSHIBA System Settings. If the computer enters Sleep Mode while a network application is active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.
Hibernation Mode The Hibernation Mode feature saves the contents of memory to the Solid State Drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer. Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the Solid State Drive. However, for safety sake, it is best to save your data manually.
Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below: 1. 2. 3. Click Power Options and then click Choose what the power button does or Choose what closing the lid does. Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid. Click the Save changes button.
Chapter 3 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section. Please handle your computer carefully to avoid scratching or damaging the surface. The Computer The following figure shows each important component of the computer.
Figure 3-1 The computer in tablet mode 22 22 23 24 27 26 25 22 27 22 5 3 2 4 28 5 1 8 7 9 10 12 11 13 14 15 16 17 6 21 20 19 1. Display screen 2. Web Camera (front) 3. Web Camera LED (front) 4. Ambient light sensor (not shown) 5. Microphone 6. Windows button 7. Power button 8. Force shutdown hole 9. Orientation lock button 10. Volume up/down button 11. Power indicator 12. Battery indicator 13. Headphone/Microphone combo jack 14. Universal Serial Bus (USB 3.
Display screen 29.5cm (11.6") LCD screen, configured with the following resolution: FHD, 1920 horizontal x 1080 vertical pixels Please be aware that, when the computer is operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries. Legal Footnote (LCD) For more information regarding LCD, please refer to the Legal Footnotes section.
Force Shut down hole Insert a slender object such as a needle into this hole to force a shut down when the computer is hung. Orientation lock button Press to lock/unlock automatic rotation of the screen orientation. Volume up/down buttons Press the button to increase or decrease the volume. Power indicator The Power indicator glows white when the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash white.
HDMI (micro) port HDMI (micro) port can connect to an HDMI cable with a Type D connector. An HDMI cable sends video and audio signals. In addition to this, it can send and receive control signals. Please refer to the HDMI port section for details. Memory media slot This slot lets you insert an SD™/SDHC™/ SDXC™ memory card, miniSD™/microSD™ Card and MultiMediaCard™. Refer to the Memory media section for more information.
2. 3. In the Playback tab, select Speakers and click Set Default button. Click OK. Cooling vents The cooling vents help the processor to avoid overheating. Web Camera (back) Your computer is also equipped with a back Web Camera used for recording video or taking photographs. Do not point the web camera directly at the sun. Do not touch or press strongly on the web camera lens. Doing so may reduce image quality.
Figure 3-2 Front view of the keyboard dock 8 6 7 9 10 11 12 5 2 4 1 3 1. Touch Pad 2. Touch Pad ON/OFF icon 3. TOSHIBA eco icon 4. Touch Pad control buttons 5. AccuPoint control buttons 6. Keyboard 7. AccuPoint 8. Computer holder 9. Hook 10. Docking connector 11. Hook 12. Eject button Product appearance depends on the model you purchased. Figure 3-3 Back view of the keyboard dock 15 13 16 14 13. DC IN 19V jack 14. LAN jack 15. HDMI port 16.
Touch Pad The Touch Pad located in the palm rest is used to control the movement of the on-screen pointer. To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go. Touch Pad ON/OFF icon Double-tap to enable/disable the Touch Pad. TOSHIBA eco icon Double-tap to enable/disable TOSHIBA eco Utility.
Eject button Begins the computer’s disconnect sequence. Once the eject button is pressed and the computer cannot communicate with external devices connected to the keyboard dock. Undock and re-dock the computer to re-establish communication. DC IN 19V jack The AC adaptor connects to this jack in order to power the computer and charge its internal batteries.
Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly. Keep foreign metal objects, such as screws, staples and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Release latch Slide and hold the release latch to the left to disengage the computer from the keyboard dock. Please refer to the Connecting TOSHIBA Keyboard Dock section to learn more details. Internal Hardware Components This section describes the internal hardware components of your computer. The actual specifications may vary depending on the model you purchased. Battery pack This computer includes a battery pack inside. However, please do not attempt to dismount or replace it by yourself.
Solid State Drive The capacity of the Solid State Drive varies depending on the model. To check which type of SSD is included in your model, open the TOSHIBA PC Health Monitor utility by clicking Desktop -> Desktop Assist (in taskbar) -> Support & Recovery -> PC Health Monitor, and then click PC Information. Please note that part of the Solid State Drive’s overall capacity is reserved as administration space.
Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller also controls the video mode and uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed at a time. Therefore, software written for a given video mode will run on any computer that supports that mode.
With the Intel® Rapid Start Technology, the Windows can rapidly resume from Hibernation Mode and battery life will be longer than when in Sleep Mode. Intel® Rapid Start Technology is enabled at factory default. The computer will switch to Hibernation Mode after two hours of Sleep Mode. You can launch the BIOS setup utility to enable/disable the function and change the specified time setting from Sleep Mode to Hibernation Mode. 1. 2. 3. 4. Launch the BIOS setup utility.
For further information on setting up Intel® Smart Connect Technology, please refer to the utility help. When Intel® Smart Connect Technology is enabled, the computer may be turned on automatically. When you carry your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer. When Intel® Smart Connect Technology is enabled, the computer will periodically wake up from sleep mode which consumes the battery power.
Power on Power off (no operation) AC adaptor not connected Remaining battery capacity is above low battery trigger point • Operates Remaining battery capacity is below low battery trigger point • Operates Remaining battery capacity is exhausted Computer shuts down • LED: off • LED: flashes amber Battery indicator Check the Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected.
User's Manual Flashing white Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition. No light Under any other conditions, the indicator does not light.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer and highlights the precautions that should be taken when using it. Operating in Tablet Mode When operating the computer in tablet mode, follow the instructions below. Figure 4-1 Operating the computer Hold the computer firmly on your forearm. Do not block the vent. Remove the AC adaptor from the computer when using it held in your forearm. Do not use the computer while walking or driving a car.
The display panel with some models works as a touch sensitive digitizer screen. However, the outer edges of the screen may be less sensitive. Please keep the Stylus Pen or the Reserve Pen inside the display area when you use it near the edges of the display panel. The position of the pen may not be recognized if you move the pen too fast towards the outer edge. Please be sure to slide the pen slowly in areas near the edges of the screen.
Calibrating digital compass If you have downloaded a compass application to use this feature, please note that the performance of any compass feature will vary depending on environmental conditions. For example, any source using electromagnetic or radio waves. Before using any compass feature the compass needs to be calibrated for accuracy.
Slide Drag your finger on the touch screen to move through what's on the screen. Swipe to select Quickly slide down an item with your finger, such as an app tile to select it. This usually opens the app commands. Swipe from edge Quickly move your finger in from the edge of the screen, without pausing when you first touch it. Swipe from the left edge: shows your recently opened apps, and so on. Swipe from the right edge: opens or closes the Charms (Search, Share, Start, Devices, Settings).
Pinch or stretch Place two or more fingers down on the Touch Pad and move them toward each other (pinch) or away from each other (stretch). This will show different levels of information or visually zooms in or out. Two-Finger Scroll Place two fingers down and slide them vertically or horizontally from anywhere on the Touch Pad. This allows you to operate the scroll bars of a window. Some of the Touch Pad operations described in this section are only supported in certain applications.
AccuPoint precautions Certain conditions can affect the on-screen pointer when using AccuPoint. For example, the pointer may travel contrary to AccuPoint operation or an error message may appear, if You touch the AccuPoint during power-up. You apply constant, soft pressure during power-up. There is a sudden temperature change. Strong stress is applied to the AccuPoint. If an error message appears, reboot the computer.
Figure 4-7 Stylus Pen 3 2 1 Figure 4-8 Reserve Pen 2 1 1. Pen point 2. Pen button 3. Eraser Pen point Provides the same function as left clicking the mouse once. Pen button Press and hold this button and touch the tip of the pen on an object. Immediately lift it to display a pop-up menu or execute a specific action. It functions as right clicking the mouse once. Eraser The virtual eraser allows you to delete notes or sketches in applications that support eraser function.
Do not tap or press the pen forcefully against the display as this could damage the pen and the screen itself. Avoid using or keeping the pen in areas where the temperature can change rapidly or in places, such as a car, where the pen is exposed to direct sunlight. Store the pen without any pressure being applied to the buttons. Failure to do so could cause a malfunction or characteristic deterioration. The pen is composed of precision parts. Do not drop the pen.
TOSHIBA is not liable for any problems arising on the products due to the use of the pen in an environment where the above conditions are not satisfied or because of its use by unspecified number of users. Removing the Reserve Pen To remove the Reserve Pen, slowly pull the Reserve Pen to remove it from the Reserve Pen slot. Figure 4-9 Removing the Reserve Pen 1 2 1. Reserve Pen slot 2.
Single tap Lightly tap the tip of the pen on an object and lift it immediately to execute an action. A single tap is similar to left clicking the mouse once. Double tap Lightly tap the tip of the pen twice on an object and lift it immediately to execute an action. A double-tap is similar to left clicking the mouse twice. Press and hold Tap the tip of the pen on the screen and hold until a white circle appears. Lift the pen to open a pop-up menu or execute a specific action.
delivered with the Stylus Pen. When these refills have run out, you can purchase a new pen set from a TOSHIBA authorized dealer. A short and worn pen point is difficult to pull out. Replace the pen point with a refill before it becomes too short to remove. It is recommended that you keep another pen set as a spare. You can buy replacement pen sets from your TOSHIBA authorized dealer.
Function Key The function keys (F1 ~ F12) are the twelve keys at the top of your keyboard. The following specific functions are executed when the function keys are pressed in combination with the FN key. Key Combination Function FN + F1 Enters ''Lock computer mode''. To restore your desktop, you need to log on again. FN + F2 Changes the power settings. FN + F3 Switches the system to Sleep Mode. FN + F4 Switches the system to Hibernation Mode. FN + F5 Changes the active display device.
Key Combination Function FN + Space Changes the display resolution. FN + Turns the keyboard backlight on or off. Some functions will show the toast notification at the edges of the screen. Those toast notifications are disabled at factory default. You can enable them in the TOSHIBA Function Key application. To access it, click Desktop -> Desktop Assist (in taskbar) -> Tools & Utilities -> Function Key.
Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off: 1. 2. 3. Hold down FN key and press any other key - this key will operate as if the overlay were off. Type upper-case characters by holding down FN + SHIFT and pressing a character key. Release FN key to continue using the selected overlay function.
Battery This section explains battery types, use, recharging methods and handling. Battery types The computer has different types of batteries. Battery pack When the AC adaptor is not connected, the computer's main power source is this lithium ion battery pack, also referred to in this manual as the main battery.
computer will enable Hibernation Mode so that you do not lose any data, and automatically turn itself off. You must recharge a battery pack when it becomes discharged. Procedures To recharge a battery pack, connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet - the Battery indicator will glow amber while the battery is being charged. Charging Time The following table shows the approximate time required to fully charge a discharged battery.
3. Charge the battery until the Battery indicator glows white. Repeat these steps two or three times until the battery recovers normal capacity. Monitoring battery capacity Remaining battery power can be monitored using the following methods. Clicking the battery icon on the Taskbar Via the Battery Status in the Windows Mobility Center window You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.
Batteries exhausted time When you turn off the power of your computer with batteries fully charged, the batteries will be exhausted within the following approximate period.
3. 4. Locate the SIM card slot. To pop the SIM card tray partially open, insert a slender object (about 10mm) such as a straightened paper clip into the eject hole. Gently pull to open the SIM card tray. Never pull the SIM card tray completely out of the slot. Figure 4-14 Open the SIM card tray 1 2 1. Slender object (Diameter 0.8mm) 2. SIM card tray Product appearance depends on the model you purchased. 5. 6. Place the SIM card into the SIM card tray with the metal connectors facing up.
Do not touch the connectors on the SIM card or on the computer. Debris on the connectors may cause access problems. Removing a SIM Card To remove the SIM card, follow the steps as detailed below: 1. 2. 3. 4. Shut down the computer - make sure the Power indicator is off. To pop the SIM card tray partially open, insert a slender object (about 10mm) such as a straightened paper clip into the eject hole. Gently pull to open the SIM card tray. Remove the SIM card from the SIM card tray.
The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on). LAN cable types The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.
2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Figure 4-16 Connecting the LAN cable 1 1. LAN jack 3. 2 2. LAN cable Plug the other end of the cable into a LAN hub connector or router. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection.
MultiMediaCard (MMC) Points to note about the memory media card SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device, and you may not reproduce any copyrighted material except for your personal enjoyment.
Do not touch the metal part of a card or expose it to liquids or let it get dirty. After using card, return it to its case. The card is designed so that it can be inserted only one way. Do not try to force the card into the slot. Do not leave a card partially inserted in the slot. Press the card until you hear it click into place. Set the write-protect switch to the lock position, if you do not want to record data. Memory cards have a limited lifespan, so it is important to backup important data.
Figure 4-18 Removing the dummy card 2 1. Memory media slot 2. 3. 1 2. Dummy card Turn the memory media so that the contacts (metal areas) face up. Insert the memory media into the memory media slot on the side of the computer. Figure 4-19 Inserting memory media 1 2 1. Memory media slot 2. Memory media Make sure the memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it.
2. 3. 4. 5. Point to memory media and click the left Touch Pad control button. Push the memory media until you hear a click to partially release it. Grasp the memory media and remove it. Insert the dummy card back into the slot. If you remove the memory media or turn off the power while the computer is accessing the memory media, you may lose data or damage the media. Do not remove the memory media while the computer is in Sleep or Hibernation Mode.
Figure 4-20 Connecting the RGB cable to the External RGB monitor port 1 2 1. External RGB monitor port 2. RGB cable There are no fastening screws for an external monitor cable on the External RGB monitor port. However, external monitor cables which have connectors with fastening screws can still be used. 2. Turn the external monitor's power on. When you turn on the power, the computer will automatically recognize the monitor and determine whether it is a color or monochrome device.
Figure 4-21 Connecting the HDMI port on the computer 1 2 1. HDMI (micro) port 2. HDMI cable (Type D connector) Figure 4-22 Connecting the HDMI port on the keyboard dock 1 2 1. HDMI port 2. HDMI cable (Type A connector) Please do not plug/unplug an HDMI display device under the following conditions: The system is starting up. The system is shutting down. When you connect a television or external monitor to the HDMI port, the display output device is set to HDMI.
2. In the Playback tab, select the playback device which you want to switch to. 3. To use the internal speakers on your computer, select Speakers. To use the television or the external monitor that you have connected to the computer, select a different playback device. 4. Click the Set Default button. 5. Click OK to close the Sound dialog.
Universal AC Adaptor If you frequently use your computer at more than one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you.
If you feel the microphone volume level is inadequate, move the Microphone Boost slider to a higher level. Audio Enhancements In order to apply the sound effects for your current speaker, follow the steps below. 1. 2. 3. Click Desktop and right click on the Speakers icon on the Taskbar, and then select Playback devices from the sub menu. Select Speakers, and click Properties. On the Enhancements tab select the sound effects you would like, and click Apply.
DTS Studio Sound DTS Studio Sound is a premium audio enhancement suite that utilizes revolutionary audio technology to provide the most immersive and realistic listening experience ever offered for a two speaker playback environment.
Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refer to each utility's online manual, help files or README.TXT file (if applicable).
TOSHIBA Display Utility TOSHIBA Display Utility includes Desktop Text Size utility, Split Screen utility and Resolution+ settings. Desktop Text Size allows you to make the text size bigger or smaller on the desktop according to your usage and favorite. You can change the text size on the display and on the title bar of windows by changing the scaling of the text size. When the scaling is smaller, more information will appear on the display simultaneously but the text size becomes smaller.
TOSHIBA Tablet Access Code Logon Utility You can use the utility to perform user login authentication using a hand-written access code. TOSHIBA System Settings This utility allows you to customize your hardware settings according to the way you work with the computer and the peripherals you use. To access this utility, click Desktop -> Desktop Assist (in taskbar) -> Tools & Utilities -> Tablet Access Code Logon Utility.
TOSHIBA eco Utility This computer is equipped with "eco mode". This mode slightly lowers performance of some devices to reduce electric power consumption. You can realize measurable power savings by using it continuously. TOSHIBA eco Utility helps control the power consumption of your computer. Various information can help you understand your degree of contribution to the environment.
TOSHIBA Service Station This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs. When enabled, this application periodically transmits to our servers a limited amount of system information, which will be treated in strict accordance with the rules and regulations as well as applicable data protection law.
System automatic Sleep/Hibernation Mode *1 This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer.
USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports. For example, if a mouse or USB keyboard is connected to a USB port, clicking the mouse button or pressing the keyboard will wakeup the computer.
After you set the password, a dialog box will be displayed asking whether you want to save it to other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place. When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or copy-and-paste the character string.
Supervisor Password If you set a Supervisor Password, some functions might be restricted when a user logs on with the User Password. To set a Supervisor Password: Desktop -> Desktop Assist -> Tools & Utilities -> Password Utility -> Supervisor Password This utility lets you do the following: Register or delete the Supervisor Password. Specify restrictions for general users.
OK Accepts your changes and closes the TOSHIBA System Settings window. Cancel Closes the window without accepting your changes. Apply Accepts all your changes without closing the TOSHIBA System Settings window. Some options shown in grey are possible to confirm their status.
It is recommended that the AC adaptor be connected while TOSHIBA Media Player is running. Power saving features may interfere with smooth playback. When TOSHIBA Media Player is used with a battery power, set the Power Options to "Balance". The screen saver is disabled while TOSHIBA Media Player is playing a video file or slideshows of photos. The computer will not enter Sleep, Hibernation and shut-down mode automatically, while TOSHIBA Media Player is running.
Your access code shall be registered by using characters, symbols, speed of your signature, pen pressure, or directions in which you move the pen between characters or symbols. Always register your access code in accordance with the procedure that appears on the screen. You need to re-enter the same code several times to register your access code properly. Use multiple characters or symbols to create an access code that is not easily identified by a third party, to prevent illegal access to your device.
By default, a few common categories have been created on first launch. If you want to create new categories, rename or delete saved categories, press and hold one category for a few seconds and then release. A pop-up menu will appear. To browse your notes, tap one of the categories, and then tap a notebook. Creating a note The application supports to create a note in rich format including text, sketches, audio and images. To create a new note, follow the steps below: 1.
Available editing options are detailed below. Depending on the note format (text, sketches, audio or images), the options may vary. Crop( ) Drag the handles to select an area to keep in the image. Tap Uncrop( ) will reset the handles. Auto Crop is provided specifically for improving snapshots of whiteboards, printed materials, etc. You can enable it by swiping from the right edge of the screen, tap Settings -> Options -> Image Optimization and select Auto Crop.
1. Swipe to select a notebook from the home screen, and tap Move to( 2. ). In the pop-up drop-down list, select a new category and tap OK. Deleting a note/notebook To delete a note, follow the steps below: 1. Tap a notebook from the home screen, swipe to select a note, and tap Delete( 2. ). Tap Delete to confirm the operation which CANNOT be undone. To delete a notebook, follow the steps below: 1. Swipe to select a notebook from the home screen, and tap Delete( 2. ).
Camera 365 for Toshiba Camera 365 for Toshiba combines photo capturing and video recording in one with the enhanced features allowing you to capture the fleeting moments. Using Camera 365 for Toshiba To launch the application, tap Camera 365 for Toshiba in the Apps view. Start capturing By default, photo mode is activated and the back Web Camera is set. You’ll see the real-time preview screen. To zoom in or zoom out, simply swipe up or down on the preview screen.
Photo mode Tap to switch between the pre-set camera modes to improve effects and enhance your photo-taking experiences. The option is not available in video mode. Normal mode( ) Normal mode is set by default. Timer mode( ) Count down before capturing a photo. 5 seconds is set by default and you can change the countdown time in the app settings. Burst mode( ) Capture a set number of photos continuously in a short amount of time. This often works best for fast moving objects or scenes.
White Balance( ) Adjust the lighting conditions manually. By default, the application automatically fine-tunes the white balance. Burst( ) Select the number of photos for Burst mode. Timer( ) Select the countdown time for Timer mode. Resolution( ) Select the camera resolution, the higher of the resolution, the better quality the captured media will be. Flicker( ) Select the frequency of the lighting conditions. Geo info( ) Turn on/off the automatic geographical tag to the photos.
examples specified here. The stored data uses a very small portion of the total hard disk capacity, approximately 10MB or less per year. This information is used to identify and provide a notification of system conditions which may effect the performance of your TOSHIBA computer. It may also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA's authorized service providers. Additionally, TOSHIBA may also use this information for quality assurance analysis.
To enter the BIOS setup utility, follow the steps below: 1. 2. 3. Save your work. In the Settings charm, click Power and then select Restart. Hold down the Volume down button until TOSHIBA Setup Utility is loaded. If TOSHIBA Keyboard Dock is connected, the BIOS setup utility can also be launched through the keyboard operation. 1. 2. 3. Save your work. In the Settings charm, click Power and then select Restart. Hold down the F2 key and then release this key one second after the computer is power on.
If your computer is equipped with TOSHIBA Keyboard Dock, please make sure it is connected before restoring the system. Creating Recovery Media This section describes how to create Recovery Media. Be sure to connect the AC adaptor when you create Recovery Media. Be sure to close all other software programs except the Recovery Media Creator. Do not run software such as screen savers which can put a heavy load on the CPU. Operate the computer at full power. Do not use power-saving features.
3. 4. 5. Insert the first blank disc into the optical disc drive tray, or insert the USB Flash Memory into one available USB port. Click Desktop -> Desktop Assist -> Support & Recovery -> Recovery Media Creator. After Recovery Media Creator starts, select the type of media and the title you wish to copy, and then click the Create button.
Recovery Media Creator can not be launched because there is no recovery partition." When there is no recovery partition, the Recovery Media Creator cannot make Recovery Media. However, if you have already created a "Recovery Media", you can use it to restore the recovery partition. If you have not created "Recovery Media", please contact TOSHIBA support for assistance.
Ordering Recovery Discs from TOSHIBA* You can order Product Recovery discs for your notebook from the TOSHIBA Europe Backup Media Online Shop. * Please note that this service is not free-of-charge. 1. 2. User's Manual Visit https://backupmedia.toshiba.eu on the Internet. Follow the on-screen instructions. You will receive your Recovery Discs within two weeks after placing your order.
Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them in a permanent error log - this will help you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made will help to identify the problem faster.
Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously then, if you still cannot correct the problem, try to identify the source - the next section provides checklists for individual components and peripherals.
If the indicator is glowing, the computer is on. Also, try turning the computer off and then on. If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the Battery indicator. If the indicator is glowing, the computer is connected to a live external power source. The computer will not load advanced options during startup The advanced option will be loaded when you hold down one of the following keys on the keyboard dock during startup.
Power Keyboard Internal display panel Solid State Drive Memory Media Card Pointing Device USB device Sound system External monitor Wireless LAN Bluetooth Power When the computer is not plugged into an AC power outlet, the battery pack is the primary power source. However, your computer also has a number of other power resources, including an intelligent power supply and a Real Time Clock (RTC) battery, all of which are interrelated with any one having the ability to produce apparent power problems.
Battery If you suspect a problem with the battery, you should check the status of the Battery indicator. Problem Procedure Battery doesn’t power the computer The battery may be discharged - connect the AC adaptor to recharge the battery. Battery doesn’t If the battery is completely discharged, it will not charge when the AC begin charging immediately, in these instances you adaptor is attached should wait a few minutes before trying again.
Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not activated - press the FN + F11 and try typing again. Output to screen is garbled Please refer to your software's documentation to ensure that it is not remapping the keyboard in any way (remapping involves changing or reassigning the function of each key). If you are still unable to use the keyboard, you should contact TOSHIBA Support.
Solid State Drive Problem Procedure Slow performance The files on the Solid State Drive may be fragmented - in this instance you should run the disk Defragmentation utility to check the condition of your files and the Solid State Drive. Please refer to the operating system's documentation or online Help File for further information on operating and using the Defragmentation utility.
Touch Pad Problem Procedure The Touch Pad does Check the Device Select settings. not work Click Desktop -> Desktop Assist (in taskbar) -> Control Panel -> Hardware and Sound -> Mouse. On-screen pointer does not respond to pointing device operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Double-tapping (Touch Pad) does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility.
USB mouse Problem Procedure On-screen pointer does not respond to mouse operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Remove the mouse from the computer and then reconnect it to a free USB port in order to ensure it is firmly attached. Double-clicking does In this instance, you should initially try changing not work the double-click speed setting within the Mouse Control utility. 1. 2. 3.
Problem Procedure USB device does not Remove the USB device from the computer and work then reconnect it to a free port in order to ensure it is firmly attached. Ensure that any required USB device drivers are properly installed - to achieve this you should refer to both the device documentation and the operating system documentation. Sound system In addition to the information in this section, please also refer to the documentation supplied with your audio device.
Problem Procedure Monitor does not turn on After confirming that the monitor's power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press the function key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected.
Bluetooth Problem Procedure Cannot access Bluetooth device Check to ensure the computer's Wireless Communication function is on. Check to ensure the Bluetooth Manager application is running on the computer and that power to the external Bluetooth device is turned on. Check to ensure that no optional Bluetooth Adaptor is installed in the computer - the built-in Bluetooth hardware cannot operate simultaneously with another Bluetooth controller.
Chapter 7 Appendix Specifications This section summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased. Size 299 (w) x 189 (d) x 12.4 (h) millimeters (computer only) (not including parts that extend beyond the main body).
AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Certification agencies China: CQC U.S. and Canada: UL listed and CSA certified No.
USA United Kingdom UL approved BS approved Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.
and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection. If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Module. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.
Turn all wireless functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction for your medical device when using any wireless functionality. Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors.
Radio Frequency Band 5GHz (5150-5850 MHz) (Revision a and n) Band 2.4GHz (2400-2483.5 MHz) (Revision b/g and n) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other. Radio Regulatory Information The Wireless device must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This product complies with the following radio frequency and safety standards. Europe Restrictions for Use of 2400.0-2483.
Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. 2. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight. Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m.
check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS-210 of the Industry Canada Rules.
Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca Taiwan Article 12 Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to an approved low power radio frequency devices.
2. 3. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations. 2. Indication for Wireless LAN The indication shown below appears on this equipment. (1)(2) (3)(4) (5) 1. 2. 3. 4. 5. 2.4 : This equipment uses a frequency of 2.4GHz.
Device Authorization This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law of Japan. Intel® Dual band Wireless-AC 7260 Intel® Dual band Wireless-N 7260 Intel® Wireless-N 7260 The Name of the radio equipment: 7260NGW DSP Research, Inc. Approval Number: D130021003 The following restrictions apply: Do not disassemble or modify the device.
Legal Footnotes Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis. CPU Central Processing Unit (CPU) Performance Legal Footnotes.
Memory (Main System) Part of the main system memory may be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities. The amount of main system memory allocated to support graphics may vary depending on the graphics system, applications utilized, system memory size and other factors.
Total Available Graphics Memory is the total of, as applicable, Dedicated Video Memory, System Video Memory and Shared System Memory. Shared System Memory will vary depending on system memory size and other factors. Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.
Index A Documentation list 2-1 AC adaptor additional 4-30 connecting 2-6 DC IN 19V jack 3-5, 3-9 Dual Pointing Device Touch Pad 6-9 E Equipment checklist 2-1 ASCII characters 4-14 External monitor problems 6-12 B Battery extending life 4-18 monitoring capacity 4-17 real time clock 3-12, 4-15 save mode 5-6 types 4-15 H Hard disk drive automatic power off 5-5 HDMI out port 3-5, 3-9 Battery indicator HW Setup accessing window Bluetooth 7-6 C Cleaning the computer 1-15 Cooling vents 3-6, 3-11 D DC
turning on the overlays 4-13 AccuPoint control buttons 4-5 Touch Pad 3-8 Pen 4-6 L Power conditions 3-15 Hibernation Mode 2-14 panel on/off 5-6 Shut Down mode 2-11 Sleep Mode 2-12 turning off 2-11 turning on 2-8 LAN cable types 4-21 connecting 4-21 M Media care Card care 4-23 Memory card care 4-24 Problems AC power 6-5 Analyzing the problem 6-2 Battery 6-6 Dual Pointing device 6-8 External monitor 6-11 Hardware and system checklist 6-4 HDD 6-8 Internal display panel 6-7 Keyboard 6-6 Memory Media Card
S SD/SDHC/SDXC Card formatting 4-23 note 4-23 Sleep Mode setting 2-12 System automatic 5-6 Sound system problems 6-11 T TOSHIBA Desktop Assist 5-1 TOSHIBA Display Utility 5-2 Touch Screen U USB device problems 6-10 V Video mode 4-32 Video RAM 3-12 W Web Camera 3-3 Wireless communication 7-4 User's Manual Index-3
