User’s Manual PORTÉGÉ M780 computers.toshiba-europe.
PORTÉGÉ M780 Table of Contents Preface General Precautions Chapter 1 Getting Started Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 System Recovery Options and Restoring the preinstalled software. . . . . . . . . . . . . . . . . . . . . . . .1-12 Chapter 2 The Grand Tour Front with the display closed . . . . . . . . . . . . . . . . . . . . . . .
PORTÉGÉ M780 Sound System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Computer Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PORTÉGÉ M780 Appendix D Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health . . . . . . . . . . . . . . . . D-2 Regulatory statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2 Appendix E AC Power Cord and Connectors Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1 Appendix F TOSHIBA PC Health Monitor Starting the TOSHIBA PC Health Monitor . . . . . . . . . . . . . . . . . . .
PORTÉGÉ M780 Copyright © 2010 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
PORTÉGÉ M780 xD-Picture Card is a trademark of FUJIFILM Corporation. Other trademarks and registered trademarks not listed above may be used in this manual. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC.
PORTÉGÉ M780 Working environment This product was designed to fulfil the EMC (Electromagnetic Compatibility) requirements to be observed for so-called “Residential, commercial and light industry environments”. TOSHIBA do not approve the use of this product in working environments other than the above mentioned “Residential, commercial and light industry environments”. For example, the following environments are not approved: ■ Industrial Environments (e.g.
PORTÉGÉ M780 Modem warning notice This information is applicable to the models equipped with a built-in modem. Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN).
PORTÉGÉ M780 Following information is only for EU-member states: Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres. The black bar indicates that the product was placed on the market after August 13, 2005.
PORTÉGÉ M780 ENERGY STAR® Program Your computer model may be Energy Star® qualified. If the model you purchased is qualified, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
PORTÉGÉ M780 GOST Description on Laser specification The optical disc drive such as Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
PORTÉGÉ M780 Preface Congratulations on your purchase of the PORTÉGÉ M780 series computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ M780 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
PORTÉGÉ M780 Icons Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on. Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key. Key operation Some operations require you to simultaneously use two or more keys.
PORTÉGÉ M780 Terminology This term is defined in this document as follows: xiv Start The word “Start” refers to the “ Windows® 7. ” button in HDD or Hard disk drive Some models are equipped with a “Solid State Drive (SSD)” instead of a hard disk drive. In this manual, the word “HDD” or “Hard disk drive” also refers to the SSD unless otherwise stated.
PORTÉGÉ M780 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
PORTÉGÉ M780 Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
PORTÉGÉ M780 Chapter 1 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
PORTÉGÉ M780 Documentation ■ PORTÉGÉ M780 Series User’s Manual ■ PORTÉGÉ M780 Series Quickstart ■ Instruction Manual for Safety and Comfort (included in User’s Manual) ■ Warranty information If any of the items are missing or damaged, contact your dealer immediately. Software The following Windows operating system and utility software are preinstalled.
PORTÉGÉ M780 Getting Started ■ All users should be sure to read the section Starting up for the first time. ■ Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.
PORTÉGÉ M780 Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
PORTÉGÉ M780 1. Connect the power cord to the AC adaptor. Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. 1. DC IN 15V jack 2. DC output plug 1 2 Figure 1-3 Connecting the DC output plug to the computer 3.
PORTÉGÉ M780 Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity. 1 1. Display panel Figure 1-4 Opening the display panel Use reasonable care when opening and closing the display panel.
PORTÉGÉ M780 Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-Up Modes, for more information. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Please refer to the section Starting up for the first time for more information. ■ Volume cannot be adjusted during Windows Setup. 1.
PORTÉGÉ M780 Turning off the power The power can be turned off in one of three modes, either Shut Down (Boot) Mode, Hibernation Mode or Sleep Mode. Shut Down mode (Boot Mode) When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system’s main screen the next time it is turned on. 1. If you have entered data, either save it to the hard disk drive or to other storage media. 2.
PORTÉGÉ M780 ■ Before entering Sleep Mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Sleep Mode. The computer or the memory module could be damaged. ■ Do not remove the battery pack while the computer is in Sleep Mode (unless the computer is connected to an AC power source). Data in memory could be lost.
PORTÉGÉ M780 When you turn the power back on, you can continue where you left when you shut down the computer. ■ When the computer is in Sleep Mode, the Power indicator will blink orange. ■ If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off into Hibernation Mode - Sleep Mode will consume more power while the computer is off.
PORTÉGÉ M780 Starting Hibernation Mode You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, The Keyboard, for further details. To enter Hibernation Mode, follow the steps below. 1. Click Start. 2. Point to the arrow icon ( ) and then select Hibernate from the menu Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid.
PORTÉGÉ M780 System Recovery Options and Restoring the preinstalled software About 1.5GB hidden partition is allocated on the hard drive for the System Recovery Options. The System Recovery Options feature will be unusable if this partition is deleted. System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes some tools to repair startup problems, run diagnostics or restore the system.
PORTÉGÉ M780 Creating Optical Recovery Discs This section describes how to create Recovery Discs. ■ Be sure to connect the AC adaptor when you create Recovery Discs. ■ Be sure to close all other software programs except the TOSHIBA Recovery Media Creator. ■ Do not run software such as screen savers which can put a heavy load on the CPU. ■ Operate the computer at full power. ■ Do not use power-saving features. ■ Do not write to the disc when the anti-virus software is running.
PORTÉGÉ M780 Restoring the pre-installed software from your created Recovery Discs If the pre-installed files are damaged, you are able to either use the Recovery Discs you have created to restore the computer to the state it was in when you originally received it. To perform this restoration, follow the steps below: When the sound mute feature has been activated by pressing the FN + ESC key, be sure to disable this to allow sounds to be heard before starting the restore process.
PORTÉGÉ M780 When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Turn off your computer. 2. While holding down 0 (zero) key on the keyboard, turn on your computer. A menu will be displayed from which you should follow the on-screen instructions.
PORTÉGÉ M780 1-16 User’s Manual
PORTÉGÉ M780 Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix H. Front with the display closed The following figure shows the computer’s front with its display panel in the closed position. 1 4 2 5 6 3 1. System indicators 2.
PORTÉGÉ M780 Wireless communication switch Slide this switch to the left to turn off Wireless LAN, Bluetooth and Wireless WAN functions. Slide it to the right to turn on the functions. Only some models are equipped with Bluetooth, Wireless LAN and Wireless WAN functions. ■ Turn Wi-Fi®, Bluetooth and Wireless WAN functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device.
PORTÉGÉ M780 Left side The following figure shows the computer’s left side. 2 1 3 5 4 1. Cooling vents 2. Security lock slot 3. Universal Serial Bus (USB 2.0) ports 4. eSATA/USB combo port 5. ExpressCard slot Figure 2-2 The left side of the computer The computer is equipped with an ExpressCard slot. Cooling vents The cooling vents help keep the processor from overheating. Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents.
PORTÉGÉ M780 Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly. This slot allows you to install a single ExpressCard device. ExpressCard slot Keep foreign metal objects, such as screws, staples and paper clips, out of the ExpressCard slot.
PORTÉGÉ M780 Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. Ultra Slim Bay An Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II or Ultra Slim Bay HDD Adaptor II can be installed in the Ultra Slim Bay, which supports Serial ATA (SATA) interface.
PORTÉGÉ M780 Back The following figure shows the computer’s back. 1 3 2 6 5 4 1. Universal Serial Bus (USB 2.0) port 2. External monitor port 3. DC IN 15V jack 4. LAN jack 5. Link indicator (green) 6. LAN active indicator (orange) Figure 2-4 The back of the computer Universal Serial Bus (USB 2.0) port One Universal Serial Bus port, which complies to the USB 2.0 standard, is provided on the back of the computer.
PORTÉGÉ M780 ■ Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. ■ Do not connect the LAN cable to a power supply. It could cause damage or malfunction. Link indicator (green) This indicator may glow green when the computer is connected to a LAN and the LAN is functioning properly. LAN active indicator (orange) This indicator may glow orange when the computer is connected to a LAN and the LAN is functioning properly.
PORTÉGÉ M780 Notches Notches on the computer engage hooks on the TOSHIBA Express Port Replicator to ensure a secure connection. Docking port This port enables connection of an optional TOSHIBA Express Port Replicator or a Slice Expansion Battery described in Chapter 3, Hardware, Utilities and Options. ■ Only the TOSHIBA Express Port Replicator can be used with this computer. Do not attempt to use any other Port Replicator. ■ Keep foreign objects out of the docking port.
PORTÉGÉ M780 Ultra Slim Bay Refer to the Right side section in this chapter for details. Ultra Slim Bay latch Slide the latch to release or secure the Ultra Slim Bay latch. Be sure to lock the Ultra Slim Bay latch before you transport or carry the computer. Ultra Slim Bay lock Lock position is used to lock the Ultra Slim Bay screw (lock position) Latch. The Ultra Slim Bay Latch is locked by securing the Ultra Slim Bay Lock screw into the lock position.
PORTÉGÉ M780 Front with the display open This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you. 2 1 20 17 11 3 12 13 6 18 5 4 13 7 21 8 9 10 19 1. Web Camera 2. Web Camera LED 3. Display screen 4. Power button 5. Power button Lock Switch 6. Cross Function button 7. ESC/Rotation button 8. Windows Security tablet button 9. TOSHIBA Assist button 10. TOSHIBA Presentation button 11.
PORTÉGÉ M780 User’s Manual Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph. It enables the transmission of video and use of video chat via the internet using specialized applications. The effective pixel count for this web camera is 1.
PORTÉGÉ M780 2-12 TOSHIBA Assist button Press this button to launch the program automatically. When power-off, Sleep Mode and Hibernation Mode, press this button to start the computer and launch the program. TOSHIBA Presentation button The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center. When power-off, Sleep Mode and Hibernation Mode, press this button to start the computer.
PORTÉGÉ M780 Microphone A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 4, Operating Basics, for more information. LCD Sensor switch This switch senses when the display panel is either closed or opened and activates the Panel Power Off/On feature as appropriate.
PORTÉGÉ M780 2-14 Power The Power indicator normally glows green when the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash orange - approximately one second on, two seconds off - both while the system is shutting down and while it remains turned off.
PORTÉGÉ M780 Keyboard indicators The following figures show the positions of the CAPS LOCK indicator and the keypad overlay indicators which show the following conditions: ■ When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed. ■ When the Arrow Mode indicator glows, the keypad overlay allows you to use cursor functions. ■ When the Numeric Mode indicator glows, the keypad overlay allows you to enter numbers. 3 2 1 1. CAPS LOCK indicator 2.
PORTÉGÉ M780 Optical disc drives The computer is configured with an Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II. Some models are equipped with an optical disc drive. A SATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical disc drives section in Chapter 4, Operating Basics.
PORTÉGÉ M780 DVDs ■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Formats The drive supports the following formats.
PORTÉGÉ M780 AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost all country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and to the computer. Please refer to Chapter 6, Power and Power-Up Modes for further information.
PORTÉGÉ M780 Chapter 3 Hardware, Utilities and Options Hardware This section describes the hardware of your computer. The actual specifications may vary depending on the model you purchased. Processor CPU Processor type varies depending on the model. To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start -> All Programs -> TOSHIBA -> Utilities -> PC Diagnostic Tool.
PORTÉGÉ M780 Video RAM The memory in a computer’s graphic adaptor, used to store the image displayed on a bitmap display. Start -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution. The amount of Video RAM can be verified by clicking the Advanced Settings button in the Screen Resolution window. The amount of Total Available Graphics memory will vary be between 1 and 2 MB depending upon system configuration.
PORTÉGÉ M780 RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure. As the AC adaptor is universal, it can receive a range of AC voltages from 100 to 240 volts, however you should note that the output current varies among different models.
PORTÉGÉ M780 Legal Footnote (Hard Disk Drive (HDD) Capacity) For more information regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Appendix G. Optical disc drive Drive The following optical disc drive is pre-installed in this computer. Some models are equipped with an optical disc drive. ■ Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.
PORTÉGÉ M780 Sound Sound system The integrated sound system provides support for the computer’s internal speakers and microphone, as allowing an external microphone and headphones to be connected via the appropriate jacks. Multimedia Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger.
PORTÉGÉ M780 Wireless LAN Some computers in this series are equipped with a Wireless LAN module that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard. Legal Footnote (Wireless LAN) For more information regarding Wireless LAN, please refer to the Legal Footnotes section in Appendix G. Wireless WAN Some computers in this series are equipped with a Wireless WAN card.
PORTÉGÉ M780 Display automatic power off *1 This feature automatically cuts off power to the computer’s display panel when there is no keyboard input for a specified time, with power being restored the next time a key is pressed. This can be specified in the Power Options. HDD automatic power off *1 This feature automatically cuts off power to the hard disk drive when it is not accessed for a specified time, with power being restored when the hard disk drive is next accessed.
PORTÉGÉ M780 Heat dispersal *1 To protect against overheating, the processor has an internal temperature sensor so that, if the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. This can be specified in the Power Options.
PORTÉGÉ M780 USB Sleep and Charge function This feature allows you to charge USB-compatible external devices such as mobile phones or portable digital music players via the USB port when your computer is in Sleep Mode, Hibernation Mode or in the shutdown state. This function is worked by the USB Sleep and Charge Utility. For more information, please refer to the Using the TOSHIBA USB Sleep and Charge Utility section in Chapter 4, Operating Basics.
PORTÉGÉ M780 TOSHIBA Value Added Package This section describes the TOSHIBA Component features pre-installed on the computer. 3-10 TOSHIBA Button Support This utility controls the following computer button functions. ■ TOSHIBA Assist ■ TOSHIBA Presentation The starting application from the button can be changed. TOSHIBA Zooming Utility This utility allows you to enlarge or reduce the icon size on the Windows Desktop, or the zoom factor associated with specific supported applications.
PORTÉGÉ M780 TOSHIBA Tablet PC Extension This section describes the pre-installed TOSHIBA Component features that come with the computer. To access these components, click Start -> All Programs -> TOSHIBA -> Tablet PC. TOSHIBA Rotation Utility This utility controls the screen orientation setting for both Laptop mode and Tablet mode.
PORTÉGÉ M780 TOSHIBA Fingerprint Utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints which can then be linked to a username and password in order to remove the need to input these details from the keyboard. Just by swiping an enrolled finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a security enabled homepage through Internet Explorer.
PORTÉGÉ M780 TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides access to specific tools, utilities and applications that make the use and configuration of the computer easier. To access this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Assist.
PORTÉGÉ M780 3-14 TOSHIBA DVD-RAM Utility This utility has the function of Physical Format and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator. To start this utility, click Start -> All Programs -> TOSHIBA -> CD&DVD Applications -> DVD-RAM Utility. TOSHIBA HDD/SSD Alert This utility includes wizard functions to monitor the Disk Drive operating status. To access this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> HDD SSD Alert.
PORTÉGÉ M780 TOSHIBA USB Sleep and Charge Utility This utility is able to either enable or disable the USB Sleep and Charge function. Shows the positions of USB ports that support the USB Sleep and Charge function and displays the battery’s remaining capacity. To start this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> USB Sleep and Charge. Trusted Platform Module (TPM) The TPM (Trusted Platform Module) is a security encryption device for the hard disk drive.
PORTÉGÉ M780 Optional devices Optional devices can expand the computer’s capabilities and its versatility. This section describes the connection or installation of the following devices: To connect optional devices (such as USB device or External monitor) to the computer, be sure to check the shape and orientation of the connector before connecting.
PORTÉGÉ M780 ExpressCard The computer is equipped with a single ExpressCard slot into which any ExpressCard device that meets industry standards, either manufactured by TOSHIBA or another vendor, can be installed. The slot supports hot plug connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps. Inserting an ExpressCard The Windows hot-install feature allows you to insert ExpressCards while the computer is turned on.
PORTÉGÉ M780 4. Grasp the ExpressCard and remove it. 1 1. ExpressCard Figure 3-2 Removing the ExpressCard 5. Insert the Dummy card into the ExpressCard slot. When you do not use an ExpressCard, please be sure to insert a Dummy card. Bridge media slot The computer is equipped with a Bridge media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.
PORTÉGÉ M780 ■ This Bridge media slot supports the following memory media. ■ Secure Digital (SD) Card (SD memory card, SDHC memory card, miniSD Card, microSD Card) ■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick PRO Duo) ■ xD picture card ■ MultiMediaCard (MMC) ■ Please note that an adaptor is required to use miniSD/microSD Card. ■ Please note that an adaptor is required to use Memory Stick PRO Duo. ■ Please note that not all memory media have been tested and verified to work correctly.
PORTÉGÉ M780 ■ The SD memory card logo is ( ■ The SDHC memory card logo is ( ). ). ■ The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 32GB. Card Type Capacities SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, 1GB, 2GB SDHC 4GB, 8GB, 16GB,32GB Memory media format New media cards are formatted according to specific standards. If you wish to reformat a media card, be sure to do so with a device that uses media cards.
PORTÉGÉ M780 Memory card care ■ Set the write-protect switch to the lock position, if you do not want to record data. ■ Memory cards have a limited lifespan, so it is important to backup important data. ■ Do not write to a card if the battery power is low. Low power could affect writing accuracy. ■ Do not remove a card while read/write is in progress. For more details on using memory cards, see manuals accompanying the cards. About the write-protect The following memory media have a function for protect.
PORTÉGÉ M780 ■ Make sure memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it. ■ When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data. ■ Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied - doing so may cause data to be lost.
PORTÉGÉ M780 Additional memory module This computer is equipped with two memory slots; Slot A is beneath the keyboard and Slot B is in the underside of the computer. You can install additional memory into the computer in order to increase the amount of system memory that is available. This section describes how to install and remove optional memory modules.
PORTÉGÉ M780 Installing a memory module (Slot A) To install a memory module, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power off - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started, if required). 2. Remove the AC adaptor and all cables and peripherals connected to the computer. 3.
PORTÉGÉ M780 8. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. ■ When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest.
PORTÉGÉ M780 10. Align the notch of the memory module with that of the memory module slot and gently insert the module into the slot at about a 45 degree angle before holding it down until the latches on either side snap into place. 1 1. Slot A Figure 3-9 Installing the memory module ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard.
PORTÉGÉ M780 11. Screw in the two screws and replace the memory module cover. 1 2 1. Screws 2. Memory module cover Figure 3-10 Seating the memory module cover 12. Insert the tabs on the front of the keyboard into the corresponding notches on the computer and place the keyboard down. When seating the keyboard, be sure to connect the circuit board if the keyboard ribbon cable was pulled out while you were removing the keyboard. 13. Replace the keyboard and secure it using the two screws.
PORTÉGÉ M780 16. Turn your computer over. 17. Turn the computer on and make sure the added memory is recognized to confirmed it, Start -> Control Panel -> System and Security -> System icon. Removing a memory module (Slot A) The slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A. To remove the memory module, follow the steps as detailed below: 1.
PORTÉGÉ M780 7. Rotate the keyboard back into place and secure the keyboard brace as described in the previous section. 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details. 9. Turn your computer over. Installing a memory module (Slot B) To install a memory module, follow the steps as detailed below: 1.
PORTÉGÉ M780 7. Align the notch of the memory module with that of the memory module slot and gently insert the module into the slot at about a 45 degree angle before holding it down until the latches on either side snap into place. 1 1. Slot B Figure 3-14 Seating the memory module ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
PORTÉGÉ M780 8. Seat the memory module cover in place and secure it with one screw. Take care to ensure that the memory module cover is firmly closed. 1 2 1. Screw 2. Memory module cover Figure 3-15 Seating the memory module cover 9. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required. 10. Turn your computer over. 11.
PORTÉGÉ M780 8. Grasp the memory module by its edges and remove it from the computer. ■ If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 1 1.
PORTÉGÉ M780 Removing the hard disk drive pack To remove the hard disk drive pack, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power off - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started, if required). 2. Remove the AC adaptor and all cables and peripherals connected to the computer. 3. Close the display panel.
PORTÉGÉ M780 7. Follow the below steps to remove the hard disk drive pack as shown in below figure. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. a. Hold the plastic tab and lift it carefully so that the hard disk drive pack slopes. Do not pull the cable. b.
PORTÉGÉ M780 2 1 a 1 3 b 1 3 c 1. Hard disk drive pack 2. Plastic tab 3.
PORTÉGÉ M780 Installing the hard disk drive pack To install the hard disk drive pack, follow the steps as detailed below: 1. Grasp the edges of the connector with one hand and the edges of the hard disk drive pack with the other hand. 2. Connect the hard disk drive to the connector. Ensure they are connected firmly. Please be careful not to pull the connector cables when you install the hard disk drive pack.
PORTÉGÉ M780 Ultra Slim Bay HDD Adaptor II You can increase your computer’s data storage capacity by installing an additional hard disk drive in the Ultra Slim Bay. To install a hard disk drive in the Ultra Slim Bay HDD Adaptor II follow the steps below. 1. Slide the lock to the unlock position and open the lid. 1 2 1. Lock 2. Lid Figure 3-20 Opening the lid 2. Insert the hard disk drive in the Ultra Slim Bay HDD Adaptor II and push forward to ensure a firm connection.
PORTÉGÉ M780 3. Close the lid and slide the lock to the lock position. 1 1. Lid Figure 3-22 Closing the lid For details on inserting the Ultra Slim Bay HDD Adaptor II in the computer’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. Connecting the monitor cable To connect a monitor, follow the steps as detailed below: 1. Turn the computer’s power off. 2.
PORTÉGÉ M780 When you turn on the power, the computer will automatically recognize the monitor and determine whether it is a color or monochrome device. In the event that you find that there are issues getting an image displayed on the correct monitor, you should consider using the FN + F5 hot key to change the display settings (if you then disconnect the external monitor before you turn the computer’s power off, be sure to press FN + F5 hot key again to switch to the internal display).
PORTÉGÉ M780 Connecting the USB floppy diskette drive To connect the drive, plug the floppy diskette drive’s USB connector into a computer’s USB port. Make sure the connector is properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins. 2 1 1. USB connector 2.
PORTÉGÉ M780 eSATA (External Serial ATA) An device corresponding to eSATA function can be connected to the eSATA/USB combo port on the computer. Connecting the eSATA device To connect an eSATA device, follow the steps as detailed below: 1. Connect an eSATA cable to the eSATA/USB combo port. Make sure the connector is properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins. 2 1 1. eSATA cable 2.
PORTÉGÉ M780 Disconnecting an eSATA device When you have finished using an eSATA device, you can follow the procedures below in order to disconnect it: 1. Wait for the indicator light of an eSATA device to go out to make sure all activity has stopped. If you disconnect an eSATA device or turn off the power while the computer is accessing the drive you may lose data or damage an eSATA device or the drive. 2. Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar. 3.
PORTÉGÉ M780 Connecting the i.LINK (IEEE1394) cable To connect the i.LINK (IEEE1394) cable, follow the steps as detailed below: 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. 2 1 1. i.LINK (IEEE1394) connector 2. i.LINK (IEEE1394) port Figure 3-27 Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.
PORTÉGÉ M780 TOSHIBA Express Port Replicator In addition to the ports available on the computer, the TOSHIBA Express Port Replicator also provides several kinds of ports. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TOSHIBA Express Port Replicator to a power source. The computer must be configured properly before connecting to a LAN.
PORTÉGÉ M780 Security lock A security locks enable you to anchor your computer a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot on its left side into which you can attach one end of the security cable, while the other end attaches to a desk or similar object. The methods used for attaching security cables differ from product to product. Please refer to the instructions for the product you are using for more information.
PORTÉGÉ M780 Battery Pack An additional battery pack can be purchased for use as either a spare or replacement. Please refer to Chapter 6, Power and Power-Up Modes, for further information. Slice Expansion Battery This battery pack increases your computer’s operating time when a main battery pack is also installed. It is connectable to the Docking port of the computer.
PORTÉGÉ M780 Chapter 4 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. Pointing Devices The pointing devices of this computer vary from model to model. ■ Digitizer screen model: The Touch Pad and the Tablet PC Pen which comes with the computer can be used as a pointing device.
PORTÉGÉ M780 The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using. You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse.
PORTÉGÉ M780 Observe the following precautions on the handling of the Tablet PC Pen. ■ In order to avoid damages to the display screen, please refrain from doing anything other than the specified operation methods. Failure to do so could cause a malfunction or characteristic deterioration. ■ Do not tap or press the Tablet PC Pen forcefully against the display as this could damage the Tablet PC Pen and the screen itself.
PORTÉGÉ M780 Removing the Tablet PC Pen To remove the Tablet PC Pen, follow the steps as described below: 1. Push the Tablet PC Pen in the Tablet PC Pen slot, so that it protrudes slightly. 2. Pull the Tablet PC Pen to remove it from the Tablet PC Pen slot. 1 2 1. Tablet PC Pen slot 2. Tablet PC Pen Figure 4-3 Removing the Tablet PC Pen Inserting the Tablet PC Pen The Tablet PC Pen is included in the small case coming with the product.
PORTÉGÉ M780 Pen actions You can use the Tablet PC Pen to enter data, start programs, move objects and execute other actions. Single tap Lightly tap the tip of the Tablet PC Pen on an object and lift it immediately to execute an action. A single tap is similar to clicking the left touch pad control button. Double tap Lightly tap the tip of the Tablet PC Pen twice on an object and lift it immediately to execute an action. A double-tap is similar to double-clicking the left touch pad control button.
PORTÉGÉ M780 Do not continue to use a broken pen tip as this may result in scratching of the display panel. When the pen tip breaks replace it with one of the refills delivered with the Tablet PC Pen. When these refills have run out, you can purchase a new pen set from a TOSHIBA authorized dealer. ■ A short and worn pen point is difficult to pull out. Replace the pen point with a refill before it becomes too short to remove. ■ It is recommended that you keep another pen set as a spare.
PORTÉGÉ M780 Inserting the Reserve Pen case To insert the Reserve Pen case, follow the steps as detailed below: 1. Insert the Reserve Pen case into the Reserve Pen case slot on the computer and slide it until it locks. 2 1 1. Reserve Pen case slot 2. Reserve Pen case Figure 4-7 Inserting the Reserve Pen case Storing and Removing the Reserve Pen from the Reserve Pen case Follow the procedures below to remove the Reserve Pen from the Reserve Pen case.
PORTÉGÉ M780 Storing the Reserve Pen in the Reserve Pen case 1. Insert the tip of the Reserve Pen into the Reserve Pen case holder and press down. 1. Reserve Pen case 2. Reserve Pen case holder 3. Reserve Pen 1 3 2 Figure 4-9 Storing the Reserve Pen in the Reserve Pen case Using the Tablet mode This section explains Tablet mode functions and use. Operating the computer in Tablet mode When operating the computer in Tablet mode, follow the instructions below.
PORTÉGÉ M780 ■ Change to Laptop mode and turn off the computer before carrying it. Do not carry the computer with power on or in Sleep Mode. Do not carry the computer while the Hard Disk Drive indicator is glowing. ■ Do not expose the computer to rapid temperature changes (such as would be the case if you brought the computer from a cold environment into a warm room).
PORTÉGÉ M780 ■ The display panel works as a touch sensitive digitizer screen. However, the outer edges of the screen may be less sensitive. Please keep the Tablet PC Pen or your finger inside the display area when you use it near the edges of the display panel. The position of the pen may not be recognized if you move the Tablet PC Pen or your finger too fast towards the outer edge. Please be sure to slide the Tablet PC Pen or your finger slowly in areas near the edges of the screen.
PORTÉGÉ M780 Changing to the Tablet mode To change from Laptop mode to the Tablet mode, follow the instructions below. 1. Open the display panel to the upright position. When rotating the display panel, be sure to keep the display panel at a 90-degree angle to the keyboard. Figure 4-12 Changing to the Tablet mode (1) ■ Place the computer on a stable, flat surface such as a desktop and rotate the display panel slowly, holding the panel at its lower part.
PORTÉGÉ M780 2. Rotate the display panel clockwise slowly. ■ When rotating display panel of your computer, be sure to slowly turn it in the proper direction, and not apply excessive force or speed. ■ Do not attempt to rotate the display panel past the maximum rotation point. Forcing the display panel past the maximum rotation point will damage the display panel. ■ Rotating the display panel counter-clockwise will break the hinge and cause the computer to cease to function correctly.
PORTÉGÉ M780 Changing to the Laptop mode To change the operating mode to the Laptop mode, follow the steps as detailed below: 1. Raise the display to the upright position carefully. 2. Rotate the display counter-clockwise slowly. 3. Close the display.
PORTÉGÉ M780 ■ Execute the following applications on Primary landscape: ■ 3D game software ■ 3D screen saver ■ Playback of a motion picture as would be the case using DVD-Video playback on the computer connected to an external DVD-ROM Drive. ■ The screen cannot automatically rotate in the following cases. You should first quit the running application and then rotate the screen: ■ Running of an application that changes the screen resolution dynamically, such as a game that is running in full-screen mode.
PORTÉGÉ M780 5. Select a screen orientation from the Orientation pull down menu and change the screen. Primary Landscape Primary Portrait Secondary Landscape Secondary Portrait You can set the orientation of the desktop screen just after rotating the display from Start -> All Programs -> TOSHIBA -> Tablet PC -> Rotation Utility.
PORTÉGÉ M780 Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to: ■ Logon to Windows and access a security enabled homepage through Internet Explorer. ■ Files and folders can be encrypted/decrypted and third party access to them prevented.
PORTÉGÉ M780 ■ Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions may cause fingerprint reading to fail. ■ Check the center of the fingerprint whorl before swiping and then ensure this is swiped along the center line of the sensor.
PORTÉGÉ M780 Observe the following to improve the fingerprint recognition success rate. ■ Enroll two or more fingers. ■ Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers. ■ Check the condition of your finger - any conditions which have changed since enrollment, such as injury, rough skin, and extremely dry, wet, soiled, dirty, oily, soaked or swollen fingers, may lower the recognition success rate.
PORTÉGÉ M780 Set up fingerprint registration Please use the following procedure when first using fingerprint authentication. ■ The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration. ■ This sensor has memory space for at least 20 fingerprint patterns. You might be able to register more fingerprint patterns depending on the sensor memory usage. 1.
PORTÉGÉ M780 Delete the fingerprint data Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your fingerprint information. Delete the fingerprint data for the currently logged in user. 1. Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Fingerprint Utility, or double click the utility icon in the Task Bar. 2.
PORTÉGÉ M780 Windows logon via fingerprint authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the computer, as user selection can be skipped. Fingerprint authentication procedure 1. Start up the computer. 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor.
PORTÉGÉ M780 Overview about Fingerprint Single sign-on feature This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive) Password) and logging onto Windows using only one fingerprint authentication when booting up. It is necessary to register the User/BIOS Password and Windows Logon Password before using the fingerprint boot authentication and this fingerprint Single sign-on feature.
PORTÉGÉ M780 TOSHIBA Button Support You can update and assign other applications to the operation panels using the TOSHIBA Button Support utility. To open TOSHIBA Button Support, please follow one of the methods listed below: ■ Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Assist, and then click the OPTIMIZE tab in the TOSHIBA Assist window. In the OPTIMIZE tab page, click TOSHIBA Button Support. ■ Hold the FN key and the Flash Cards bar will appear at the top of the screen.
PORTÉGÉ M780 Web Camera Some models are equipped with Web Camera, which is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph. It enables the transmission of video and use of video chat via the internet using specialized applications.
PORTÉGÉ M780 Using the TOSHIBA Face Recognition TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier. ■ TOSHIBA Face Recognition does not guarantee the correct identification of a user.
PORTÉGÉ M780 How to register the Face Recognition Data Take a picture for facial verification purposes, and register the data needed when you log in. To register the data needed when you log in, follow the steps as described below: 1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> Face Recognition. ■ The Registration screen is displayed for a logged-in user whose face has not been registered.
PORTÉGÉ M780 How to Delete the Face Recognition Data Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below: 1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> Face Recognition. The Management screen is displayed. 2. Select a user which you want to delete in the Management screen. 3. Click the Delete button. “You are about to delete the user data.
PORTÉGÉ M780 1:1 Mode Login screen 1. Turn on the computer. 2. The Select Tiles screen will be displayed. 3. 4. 5. 6. 7. Select Start face recognition ( ). The Select Account screen will be displayed. Select the account, and click the arrow button. “Please face the camera” will be displayed. Verification will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another.
PORTÉGÉ M780 Removing an optical disc drive module To remove the optical disc drive, follow the steps as described below: 1. Save your work. 2. Turn the computer’s power off - ensure that the Power indicator is off. 3. Remove all cables and peripherals that are connected to the computer. 4. Close the display panel. Always make sure the display panel is closed in Laptop mode before turning the computer upside down.
PORTÉGÉ M780 Inserting a Ultra Slim Bay HDD Adapor II module To insert the Ultra Slim Bay HDD Adaptor II, follow the steps as described below: 1. Insert the Ultra Slim Bay HDD Adaptor II in the computer as shown below and press until the Ultra Slim Bay latch clicks. 2. Remove the Ultra Slim Bay lock screw from the Unlock position. 3. If you want to lock the Ultra Slim Bay HDD Adaptor II, set the Ultra Slim Bay lock screw in the hole for the lock position. 3 1 2 1. Unlock position 2.
PORTÉGÉ M780 2 1 1. Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II unit 2.
PORTÉGÉ M780 Using optical disc drives The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD-ROM, an indicator on the drive glows. Use the DVD playback application to view DVD-Video discs.
PORTÉGÉ M780 3. Lay the CD/DVD, label side up, in the disc tray. 1 1. Laser lens Figure 4-24 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat. ■ Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment.
PORTÉGÉ M780 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button. Figure 4-25 Closing the CD/DVD disc tray Removing discs To remove the CD/DVD, follow the steps as detailed below: Do not press the eject button while the computer is accessing the media drive.
PORTÉGÉ M780 Optical Drive Auto Lock This function automatically locks the optical disc drive eject button if the computer detects any vibration or other shocks while running on the battery. This function prevents the disc tray from opening even if the eject button is pushed unexpectedly. When the Optical Drive Auto Lock is on, there will be key mark on the bottom right of the Optical Drive Power icon in the Taskbar. To enable this function, turn the Optical Drive Power ON.
PORTÉGÉ M780 1 Diameter 1.0mm 1. Eject hole Figure 4-27 Manual release with the eject hole Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the disc tray, the CD/DVD could fly off the spindle and cause injury.
PORTÉGÉ M780 Important message Before you write or rewrite to any of the media supported by the Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II, please read and follow all of the setup and operating instructions in this section.
PORTÉGÉ M780 DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 MITSUBISHI KAGAKU MEDIA Co.,Ltd. (for 8x and 16x speed media) TAIYO YUDEN Co.,Ltd.(for 8x and 16x speed media) Hitachi Maxell,Ltd. (for 8x and 16x speed media) DVD-R (Dual Layer): MITSUBISHI KAGAKU MEDIA Co.,Ltd. (for 4x and 8x speed media) DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 Victor Company of Japan, Ltd. (JVC) (for 4x and 6x speed media) MITSUBISHI KAGAKU MEDIA Co.,Ltd.
PORTÉGÉ M780 ■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD-RAM media will be affected by the quality of the disc itself and the way in which it is used. ■ There are two types of DVD-R media available, authoring discs and general use discs. Do not attempt to use authoring discs as only general use discs can be written to by a computer drive. ■ You can use both DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge.
PORTÉGÉ M780 ■ CD-RW (Ultra Speed +) media should not be used as data may be lost or damaged. ■ You should always write from the computer’s hard disk drive onto the CD/DVD - do not try to write from shared devices such as a server or any other network device. ■ Writing with software other than TOSHIBA Disc Creator has not been confirmed, therefore operation with other software applications cannot be guaranteed.
PORTÉGÉ M780 TOSHIBA Disc Creator Please be aware of the following limitations when you use the TOSHIBA Disc Creator: ■ DVD Video cannot be created using TOSHIBA Disc Creator. ■ DVD Audio cannot be created using TOSHIBA Disc Creator. ■ You cannot use TOSHIBA Disc Creator’s “Audio CD for Car or Home CD Player” function to record music to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media.
PORTÉGÉ M780 Data Verification To verify that data has been written or rewritten correctly to a data CD/DVD you should follow the steps below before you begin the write/rewrite process: 1. Click Start -> All Programs -> TOSHIBA -> CD&DVD Application -> Disc Creator to access the TOSHIBA Disc Creator utility. 2. Open the Data CD/DVD Setting dialog box by one of the following methods: ■ Click the Recording settings button ( ) for writing on the main toolbar in the Data CD/DVD mode.
PORTÉGÉ M780 ■ It is recommended the AC adaptor be connected when playing DVD-Video. Power saving features may interfere with smooth playback. When playing DVD-Video using battery power, set the Power Options to “Balance”. ■ Screen savers will not display while playing a movie in the “TOSHIBA DVD PLAYER”. The computer will also not go into Sleep Mode, Hibernation Mode or shutdown while using “TOSHIBA DVD PLAYER”.
PORTÉGÉ M780 ■ Carry out the installation/uninstallation of the “TOSHIBA DVD PLAYER” under a user account with administrator rights. ■ Do not change Windows Users while “TOSHIBA DVD PLAYER” is running. ■ For some DVD Video discs, using the control window to change the audio track will also change the subtitle track. Starting TOSHIBA DVD PLAYER Use the following procedure to start “TOSHIBA DVD PLAYER”. 1. Insert an DVD-Video in the Ultra Slim Bay DVD Super Multi drive while Windows 7 is running.
PORTÉGÉ M780 Open TOSHIBA DVD PLAYER HELP TOSHIBA DVD PLAYER features and instructions are also explained in detail in “TOSHIBA DVD PLAYER Help”. Use the following procedure to open “TOSHIBA DVD PLAYER Help”. ■ Click the “Help” button ( ) in the Display Area. Media care This section provides tips on protecting data stored on your CD’s, DVD’s and floppy diskettes. Handle your media with care.
PORTÉGÉ M780 5. Never use a pencil for writing on a floppy diskette label as the dust from the pencil lead could cause a system malfunction if it found its way onto the computer’s components. In this instance, always use a felt-tipped pen and write the label first before applying it to the floppy diskette. 6. Never put a floppy diskette in a location where water or other liquid may make contact with it, or where it is excessively damp - either of these conditions could cause data loss. 7.
PORTÉGÉ M780 Audio Enhancements In order to apply the sound effects for your current speaker, follow the steps below. 1. Right click on the speaker icon on the Taskbar, and select Playback devices from the sub menu. 2. Select Speakers, and click Properties. 3. On the Enhancements tab select the sound effects you would like, and click Apply. Realtek HD Audio Manager You can confirm and change the audio configuration using the Realtek HD Audio Manager.
PORTÉGÉ M780 TOSHIBA Mic Effect TOSHIBA Mic Effect provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network. If you wish to communicate with someone on your computer, you can use a messenger application. However, with such an application, you would hear your own voice returning to you as echo during the communication if you did not use a headset system or headphone. TOSHIBA Mic Effect will reduce these echoes generated on your computer.
PORTÉGÉ M780 Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. The built-in modem can be used only in specified countries and regions. Using the modem in an area not specified for use may cause a system failure. Check the specified areas carefully before using it. To select a region, follow the steps as detailed below: 1.
PORTÉGÉ M780 Location list for region selection. Displays a sub-menu appears which details location information. Open dialog box, if the modem and Telephony Current Location region code do not match. Displays a warning if the current settings for both region code and telephony location are different. Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed from which you should select the appropriate communications port for your modem to use.
PORTÉGÉ M780 1. Plug the end of the modular cable into the computer’s modem jack. 2. Plug the other end of the modular cable into a telephone jack. 1 2 1. Modem jack 2. Telephone jack Figure 4-29 Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.
PORTÉGÉ M780 Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. Only some models are equipped with both Wireless LAN and Bluetooth functions. ■ Do not use the Wireless LAN (Wi-Fi), Bluetooth or Wireless WAN functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi, Bluetooth or Wireless WAN operation.
PORTÉGÉ M780 The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard - the actual transmission speed will be lower than the theoretical maximum speed. Setting 1.
PORTÉGÉ M780 Security Two advanced security mechanisms ensure a high level of security: ■ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ■ Encryption prevents eavesdropping and maintains link privacy.
PORTÉGÉ M780 Wireless communication Indicator The wireless communication indicator shows the status of the computer’s wireless communication functions. Indicator status Indication Indicator off The wireless communication switch is off - no wireless functionality is available. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
PORTÉGÉ M780 Connecting the LAN cable To connect the LAN cable, follow the steps as detailed below: ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. ■ Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur.
PORTÉGÉ M780 Disconnecting the LAN cable To disconnect the LAN cable, follow the steps as detailed below: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub or router in the same manner. Check with your LAN administrator and hardware or software vendor before disconnecting from the hub.
PORTÉGÉ M780 ■ Disconnect the AC adaptor and all peripherals before moving the computer. ■ Close the display panel. Always make sure the display panel is closed in Laptop mode before turning the computer upside down. ■ Do not pick up the computer by its display panel. ■ Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury.
PORTÉGÉ M780 Taskbar icon State Icon Description Normal TOSHIBA HDD Protection is enabled. Protection TOSHIBA HDD Protection is active. The hard disk drive head is in a safe position. OFF TOSHIBA HDD Protection is disabled. TOSHIBA HDD Protection Properties You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click Start -> All Programs -> TOSHIBA -> Utilities -> HDD Protection Settings.
PORTÉGÉ M780 ■ This 3D object virtually represents the Computer’s internal Hard Disk Drive. This representation may vary from the actual number of disks, disk rotation, head movement, part size, shape and direction. ■ This feature may use a large amount of CPU and memory on some models. The computer may become slow or sluggish when attempting to run other applications while the 3D Viewer is displayed.
PORTÉGÉ M780 However, the USB Sleep and Charge function may not work with certain external devices even if they are compliant with the USB specification. In those cases, turn the power of the computer ON to charge the device. ■ When USB Sleep and Charge function is enabled, USB bus power (DC5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC5V) is similarly supplied to the external devices which are connected to the compatible ports.
PORTÉGÉ M780 Enabling USB Sleep and Charge This utility can be used to enable and disable the USB Sleep and Charge function in groups. USB Sleep and Charge compatible USB ports are assigned to each group. Select the check boxes for each group to enable the USB Sleep and Charge function for the USB ports assigned to that group. In the default state all groups are disabled.
PORTÉGÉ M780 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer. The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
PORTÉGÉ M780 Function keys: F1 … F12 The function keys (not to be confused with the special FN key) are the twelve keys at the top of your keyboard - these keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed and, when used in combination with the FN key, those keys marked with icons also execute specific functions on the computer.
PORTÉGÉ M780 Press FN + F10 or FN + F11 to access the computer’s integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Please refer to the Keypad overlay section in this chapter for more information on how to operate these keys, taking care to note that the power on default for both settings is off. Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
PORTÉGÉ M780 Sleep: Pressing FN + F3 switches the system to Sleep Mode. Hibernate: Pressing FN + F4 switches the system to Hibernation Mode. Output: Pressing FN + F5 changes the active display device. Brightness Down: Pressing FN + F6 decreases the computer’s display panel brightness in individual steps. Brightness Up: Pressing FN + F7 increases the computer’s display panel brightness in individual steps.
PORTÉGÉ M780 ODD: Pressing FN + Tab turns the power of the optical disc drive on/off or ejects the disc tray. TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows. TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows.
PORTÉGÉ M780 Keypad overlay Your computer’s keyboard does not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyboard with the relevant keys having grey letters at their front edge. The overlay provides the same functions as the numeric keypad on a standard 104/105-key enhanced keyboard. Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control.
PORTÉGÉ M780 Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off: 1. Hold down FN key and press any other key - this key will operate as if the overlay were off. 2. Type upper-case characters by holding down FN + SHIFT and pressing a character key. 3. Release FN key to continue using the selected overlay function.
PORTÉGÉ M780 5-8 User’s Manual
PORTÉGÉ M780 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and any internal batteries. This chapter provides details on making the most effective use of these resources, and includes information on charging and changing batteries, tips for saving battery power, and information on the different power-up modes.
PORTÉGÉ M780 Power conditions continued AC adaptor connected AC adaptor not connected 6-2 Power on Power off (no operation) 2nd battery fully charged • Operates • No charge • LED: 2nd battery green DC IN green • No charge • LED: 2nd battery green DC IN green 2nd battery partially charged or no charge • Operates • Charge *2 • LED: 2nd battery orange DC IN green • Quick charge *2 • LED: 2nd battery orange DC IN green No 2nd battery installed • Operates • No charge • LED: 2nd battery off DC IN gre
PORTÉGÉ M780 Power conditions continued Power on AC adaptor not connected 2nd battery charge is above low battery trigger point • Operates • LED: 2nd battery off DC IN off 2nd battery charge is below low battery trigger point • Operates • LED: 2nd battery flashes orange DC IN off 2nd battery charge is exhausted Computer shuts down *3 No 2nd battery is installed • No operation *5 • LED: 2nd battery off DC IN off Power off (no operation) *1 When the Slice Expansion Battery is not charging.
PORTÉGÉ M780 Monitoring of power condition As shown in the below table, the Battery, 2nd battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the main battery and the 2nd battery indicator to determine the status of the Slice Expansion Battery.
PORTÉGÉ M780 Power indicator Check the Power indicator to determine the power status of the computer the following indicator conditions should be noted: Green Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition. In Sleep Mode, this indicator will turn on for one second and off for two seconds.
PORTÉGÉ M780 Real Time Clock (RTC) battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off. If the RTC battery becomes completely discharged, the system will lose this information and the real time clock and calendar will stop working - in this instance the following message will be displayed when you turn on the power: S **** RTC Power Failure **** Check system.
PORTÉGÉ M780 ■ Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function. Charging the batteries When the power in the battery pack becomes low, the Battery indicator will flash orange to indicate that only a few minutes of battery power remain.
PORTÉGÉ M780 Battery charging notice The battery may not begin charging immediately under the following conditions: ■ The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, you should charge it at room temperature of between 5°C to 35°C (41°F to 95°F). ■ The battery is nearly completely discharged.
PORTÉGÉ M780 Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on: ■ Processor speed ■ Screen brightness ■ System Sleep Mode ■ System Hibernation Mode ■ Display power off period ■ Hard disk drive power off period ■ How often and for how long you use the hard disk drive and external disk(c) drives, for example, optical disc and floppy diskette drive.
PORTÉGÉ M780 Extending battery life To maximize the life of your battery packs: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps as detailed below. 1. Turn off the computer’s power. 2. Disconnect the AC adaptor and turn on the computer’s power - if it does not turn on then go to Step 4. 3. Operate the computer on battery power for five minutes.
PORTÉGÉ M780 Removing the battery pack To remove a discharged battery, follow the steps as detailed below: 1. Save your work. 2. Turn the computer’s power off - ensure that the Power indicator is off. 3. Remove all cables and peripherals that are connected to the computer. 4. Close the display panel and turn the computer upside down. Always make sure the display panel is closed in Laptop mode before turning the computer upside down. 5.
PORTÉGÉ M780 Installing the battery pack To install a battery pack, follow the steps as detailed below: Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries. 1. Insert the battery pack as far as it will go into the computer (1). 2. Ensure that the battery pack is securely in place and the battery lock (2) is in its ( ) position. 1 2 1. Battery pack 2.
PORTÉGÉ M780 3. Remove the protective cap from the Slice Expansion Battery. 4. Open latches on the Slice Expansion Battery and fit a tab on the battery into the docking port on the underside of the computer. 1. Latches 2. Tab 3. Docking port 1 2 3 Figure 6-4 Seating the Slice Expansion Battery 5. Close the latches to secure the Slice Expansion Battery to the computer. 1.
PORTÉGÉ M780 5. Open the release latches in the direction of the arrows. 1. Latches 1 Figure 6-6 Releasing the latches 6. Lift off the Slice Expansion Battery. Figure 6-7 Removing the Slice Expansion Battery 7. Be sure to replace the protective cap before storing the Slice Expansion Battery.
PORTÉGÉ M780 TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from the Windows password. User Password To start the utility, point to or click the following items: Start -> All Programs -> TOSHIBA -> Utilities -> Password Utility The User Password dialog box contains one main field: User Password.
PORTÉGÉ M780 ■ Change (button) Click this button to change a registered password. Before you can change a password, you must first enter the current password correctly. Please use BIOS Setup to change or delete the HDD Passwords or to set the HDD Master Password. ■ Owner String (text box) You can use this box to associate text with the password. After you enter text, click Apply or OK. When the computer is started, this text will be displayed together with the prompt asking you to enter a password.
PORTÉGÉ M780 The password is necessary only if the computer was Shutdown and Hibernation in Boot Mode. It is not needed in Sleep Mode and Restart. To enter a password manually, follow the steps as detailed below: 1. Turn on the power as described in Chapter 1, Getting Started. The following message will appear in the screen: S Password= 2. Enter the Password. 3. Press ENTER. If you enter the password incorrectly three times in a row, the computer shuts off.
PORTÉGÉ M780 Power-up modes The computer has three different power-up modes as follows: ■ Boot Mode: The computer will shut down without saving data in view of this you must always save your work before you turn the computer off. ■ Hibernation Mode: Data in memory will be saved to the hard disk drive. ■ Sleep Mode: Data will be maintained in the computer’s memory. Please refer to the sections Turning on the power and Turning off the power in Chapter 1, Getting Started, for further information.
PORTÉGÉ M780 Chapter 7 HW Setup This chapter explains how to use the TOSHIBA HW Setup program to configure your computer, and provides information on settings for various functions. Accessing HW Setup To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Utilities -> HWSetup. HW Setup window The HW Setup window contains a number of tabs (General, Display, Boot Priority, Keyboard, CPU, LAN, SATA and USB) to allow specific functions of the computer to be configured.
PORTÉGÉ M780 General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays the installed BIOS Version and date, and the EC Version. Display Power On Display This tab allows you to select the display to be used when the computer is started.
PORTÉGÉ M780 Boot Priority Boot Priority Options This tab allows you to set the priority for booting the computer. The Boot Priority Options setting window will be displayed as shown below. Click the up and down arrow buttons to adjust the priority. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB floppy diskette drive *1. N Selects the network. 1 Selects the built-in hard disk drive.
PORTÉGÉ M780 If a Supervisor Password has been set, manual boot device selection functions may be restricted. The boot device selection methods described above will not change the boot priority settings that have been configured in HW Setup. In addition, if you press a key other than one of those listed, or if the selected device is not installed, the system will continue to boot according to the current and available settings in HW Setup.
PORTÉGÉ M780 CPU This function allows you to set the processor’s operating mode. Dynamic CPU Frequency Mode This option allows you to configure the power saving modes associated with the processor - the following settings are available: Dynamically Switchable The processor’s power consumption and automatic clock speed switching functions are enabled - in use the processor’s operation is automatically switched when necessary (default).
PORTÉGÉ M780 Connect the AC adaptor when using the Wake-up on LAN function. The battery retention time will be shorter than the times listed in this manual when this function is enabled. Refer to the section in chapter 6, Retaining data with power off. Enabled Enables Wake-up on LAN from shutdown. Disabled Disables Wake-up on LAN from shutdown. (Default) Built-in LAN This feature enables or disables the Built-in LAN. Enabled Enables Built-in LAN functions (Default).
PORTÉGÉ M780 SATA eSATA This feature allows you to set conditions for SATA. Enabled Enables the eSATA port. (Default) Disabled Disables the eSATA port in order to save power. SATA Interface setting This feature allows you to set SATA interface setting. User’s Manual Performance Let HDD/SSD work with maximum performance. (Default) Battery life Let HDD/SSD work with battery life mode. If this setting is selected, this caused performance down.
PORTÉGÉ M780 7-8 User’s Manual
PORTÉGÉ M780 Chapter 8 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
PORTÉGÉ M780 ■ Make sure all optional accessories are configured properly in the computer’s setup program and that all required driver software has been loaded (please refer to the documentation included with the optional accessories for further information on its installation and configuration). ■ Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. ■ Inspect all connecting cables for loose wires and all connectors for loose pins.
PORTÉGÉ M780 Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted - in these instances try loading another copy of the software if possible. If an error message appears while you are using a software package you should refer to the documentation supplied with it as this will usually include a problem solving section or a summary of error messages.
PORTÉGÉ M780 System start-up When the computer does not start properly, check the following items: ■ Self Test ■ Power Sources ■ Power-on Password Self test While booting up the computer, self test is executed automatically and the TOSHIBA logo is displayed on the screen. This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system according to how the Boot Priority option is set within the TOSHIBA HW Setup program.
PORTÉGÉ M780 Overheating power down In the event that the computer’s internal operating temperature becomes too high, the system will automatically enter either Hibernation Mode or Sleep Mode and shut itself down. Problem Procedure Computer shuts down and DC IN indicator blinks orange Leave the computer off until the DC IN indicator stops blinking. It is recommended to leave the computer off until the interior reaches room temperature even though the DC IN indicator stops blinking.
PORTÉGÉ M780 Battery If you suspect a problem with the battery, you should check the status of the DC IN indicator as well as the Battery indicator. Please refer to Chapter 6, Power and Power-Up Modes, for more information on these indicators, together with general battery operation. Problem Procedure Battery doesn’t power the computer The battery may be discharged - connect the AC adaptor to recharge the battery.
PORTÉGÉ M780 Real Time Clock Problem Procedure The following message is Displayed on the screen: RTC Power Failure. Check system. Then press [F2] key. The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the BIOS setup application by using the following steps: 1. Turn on the computer while pressing the F2 key, and then release the F2 key when the TOSHIBA Leading Innovation >>> screen appears - the BIOS setup application will load. 2.
PORTÉGÉ M780 Internal display panel Apparent computer’s display panel problems may be related to the computer’s setup and configuration - please refer to Chapter 7, HW Setup for further information. Problem Procedure No display Press the FN + F5 hot keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the computer’s display panel.
PORTÉGÉ M780 Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check to see whether that is a floppy diskette in the floppy diskette drive or a CD-ROM/DVDROM in the optical disc drive - if so remove it and try to start the computer again. If this has no effect, check the Boot Priority setting within the TOSHIBA HW Setup utility please refer to the Boot Priority section in Chapter 7, HW Setup, for further information.
PORTÉGÉ M780 Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, press the FN + Tab hot key and turn on the power (for some models). Open the disc tray and make sure the CD/DVD is properly seated.
PORTÉGÉ M780 USB floppy diskette drive For further information, please refer to Chapter 3, Hardware, Utilities and Options. Problem Procedure Drive does not operate Check the connection between the computer and the drive to ensure that it is properly attached.
PORTÉGÉ M780 SD/SDHC Card For further information, please refer to Chapter 3, Hardware, Utilities and Options. Problem Procedure SD/SDHC Card error occurs Remove the SD/SDHC Card from the computer and then reinsert it in order to ensure it is firmly connected. If the problem persists, then you should refer to the documentation supplied with your SD/SDHC Card for further information.
PORTÉGÉ M780 xD picture card For further information, please refer to Chapter 3, Hardware, Utilities and Options. Problem Procedure xD picture card error occurs Remove the xD picture card from the computer and then reinsert it in order to ensure it is firmly connected. If the problem persists, then you should refer to the documentation supplied with your xD picture card for further information.
PORTÉGÉ M780 Pointing device If you are using a USB mouse, you should also refer to both the USB device section in this chapter, and the documentation supplied with your mouse. Touch Pad 8-14 Problem Procedure On-screen pointer does not respond to pointing device operation In this instance the system might be busy - Try moving the mouse again after waiting a short while.
PORTÉGÉ M780 USB mouse User’s Manual Problem Procedure On-screen pointer does not respond to mouse operation In this instance the system might be busy Try moving the mouse again after waiting a short while. Double-clicking does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1. To access this utility, click Start -> Control Panel -> Hardware and Sound -> Mouse. 2. Within the Mouse Properties window, click the Buttons tab.
PORTÉGÉ M780 Fingerprint Sensor Problem Procedure Reading of the fingerprint was not successful. In this instance you should try the fingerprint reading operation again using the correct finger position please refer to Using the Fingerprint Sensor in Chapter 4, Operating Basics, for further information. Alternatively, you should try the recognition process again using another enrolled finger. The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint.
PORTÉGÉ M780 USB Sleep and Charge function Problem Procedure I cannot use the USB Sleep and Charge function. USB Sleep and Charge function may be disabled. Select the “Enable USB Sleep and Charge” check box in the TOSHIBA Sleep and Charge utility to enable this function. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons.
PORTÉGÉ M780 Problem Procedure External devices connected to the compatible ports do not work when connected to a compatible port. Some external devices may not work when connected to a compatible port if the USB Sleep and Charge function is enabled. Reconnect the external device after turning the computer ON.
PORTÉGÉ M780 Additional memory module Please also refer to Chapter 3, Hardware, Utilities and Options, for further information on installing and removing memory modules. User’s Manual Problem Procedure If there is a memory malfunction, the Power indicator will repeatedly flash (on for 0.5 seconds, off for 0.5 seconds) in the following patterns; If there is an error in only slot A: orange twice, then green once. If there is an error in Slot B: orange once, then green twice.
PORTÉGÉ M780 Sound system In addition to the information in this section, please also refer to the documentation supplied with your audio device. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Please check to see if Mute is turned to Off Check to make sure the headphone connection is secure. Check within the Windows Device Manager application to ensure the sound device is enabled and that the device is properly working.
PORTÉGÉ M780 External monitor Please also refer to Chapter 3, Hardware, Utilities and Options, and to the documentation supplied with your monitor for further information. Problem Procedure Monitor does not turn on After confirming that the monitor’s power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor.
PORTÉGÉ M780 i.LINK (IEEE1394) device Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Click Start -> Control Panel -> Hardware and Sound -> Device Manager. In the Device Manager window, right-click the computer’s name, and then click Add legacy hardware from the shortcut menu. Follow the on-screen directions. Restart Windows.
PORTÉGÉ M780 Problem Procedure Character display becomes garbled during a communication When transmitting data you should ensure that the parity bit and stop bit settings correspond with those of the remote computer - you should check the flow control and communication protocol settings within your communication application. You cannot receive an incoming call Ensure that the communication application’s rings before auto answer feature is set correctly.
PORTÉGÉ M780 Bluetooth For further information on Bluetooth wireless communication, please refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Check to ensure the computer’s Wireless Communication Switch is set to on. Check to ensure the Bluetooth Manager application is running on the computer and that power to the external Bluetooth device is turned on.
PORTÉGÉ M780 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions This section summarizes the computer’s technical specifications. Physical Dimensions User’s Manual Weight (typical) * 1.99 kilograms, configured with: 30.7cm(12.1")WXGA, 1,024 MB RAM, 160GB HDD, Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II, LAN (1000M bps), Wireless LAN, modem, Tablet PC Pen. * In the case of digitizer screen model.
PORTÉGÉ M780 Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5°C (41°F) to 35°C (95°F) 20% to 80% (noncondensing) Non-operating -20°C (-4°F) to 65°C (149°F) 10% to 90% (noncondensing) Wet-bulb temperature 26°C maximum Conditions Altitude (from sea level) Operating -60 to 3,000 meters Non-operating -60 to 10,000 meters maximum Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 V DC 5.
PORTÉGÉ M780 Built-in Modem This information is applicable to the models equipped with a built-in modem. Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications User’s Manual Communication system Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) V.21/V.
PORTÉGÉ M780 A-4 User’s Manual
PORTÉGÉ M780 Appendix B Display Controller and Video mode Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. Due to the display panel’s increased resolution, lines may appear broken in when displaying images in full-screen text mode.
PORTÉGÉ M780 B-2 User’s Manual
PORTÉGÉ M780 Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications Form Factor Compatibility Network Operating System Media Access Protocol PCI Express Mini Card ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance.
PORTÉGÉ M780 The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. ■ The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. ■ Range is also impacted due to “obstacles” in the signal path of the radio that may either absorb or reflect the radio signal.
PORTÉGÉ M780 *2 The band width and the channel which can be used depends on the installed wireless LAN module. And the approved channels on using are different at each country or region. When using these channels in any country or region, refer to the addendum sheet which is Approved Countries/Regions for use.
PORTÉGÉ M780 120 5600*1 124 5620*1 128 5640*1 132 5660*1 136 5680*1 140 5700*1 149 5745*1 153 5765*1 157 5785*1 161 5805*1 165 5825*1 *1 The channel which can be used depends on the installed wireless LAN module. And the approved channels on using are different at each country or region.
PORTÉGÉ M780 Appendix D Bluetooth wireless technology Interoperability Bluetooth Adaptor from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver. 2.1+EDR, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
PORTÉGÉ M780 Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
PORTÉGÉ M780 Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
PORTÉGÉ M780 In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A.
PORTÉGÉ M780 Appendix F TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption, battery health and the system cooling, informing you of significant system conditions. This application recognizes the system and individual component serial numbers, and will track specific activies related to the computer and their usage.
PORTÉGÉ M780 Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started using the following methods: ■ Click Start -> All Programs -> TOSHIBA -> Utilities -> PC Health Monitor. ■ Click the icon ( ) in the notification area, then click the “Enable PC Health Monitor...” message for the first time you run the application and “Run PC Health Monitor...” every time thereafter. No matter which method is used, the TOSHIBA PC Health Monitor explanation screen will be displayed.
PORTÉGÉ M780 Cleaning the Cooling module This section explains how to clean the Cooling module. If you use the computer for a long period, the inside of the computer may become hot. Always allow the computer to cool to room temperature before you clean the cooling module. 1. Before cleaning the Cooling module, you should shut down the computer and remove the battery pack. Follow the steps as described below: a.
PORTÉGÉ M780 4. Lift the Fan hood up and out. 1 1. Fan hood Figure F-2 Removing the Fan hood 5. Clean the Cooling module using a vacuum cleaner or other cleaning tool. Do not use a ball pen, cotton swap or similar to remove dust. If these touch the inside of the computer, it could be damaged or become clogged, leading to further problems. 6. Put the Fan hood back into the computer. 7. Slide the Cooling module cover back into place on the computer to reattach. 8.
PORTÉGÉ M780 Appendix G Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis, unless you have selected all those features.
PORTÉGÉ M780 Under some conditions, your computer product may automatically shut-down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions.
PORTÉGÉ M780 Hard Disk Drive (HDD) Capacity One Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content.
PORTÉGÉ M780 USB Sleep and Charge The “USB Sleep and Charge function” may not work with certain external devices even if they are compliant with the USB specification. In those cases, turn the power of the computer ON to charge the device. Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media.
PORTÉGÉ M780 Appendix H If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
PORTÉGÉ M780 TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Blumenstrasse 26 93055 Regensburg Germany +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. PORTÉGÉ M780) Model number: (e.g. PSL55EYXT) Serial number: (e.g.
PORTÉGÉ M780 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
PORTÉGÉ M780 FIR: fast infrared GB: gigabyte HDD: hard disk drive IDE: integrated drive electronics IEEE: Institute of Electrical and Electronics Engineers I/O: input/output IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte PC: personal computer PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial
PORTÉGÉ M780 alternating current (AC): Electric current that reverses its direction of flow at regular intervals. analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines.
PORTÉGÉ M780 bps: Bits per second. Typically used to describe the data transmission speed of a modem. buffer: The portion of the computer’s memory where data is temporarily stored. Buffers often compensate for differences in the rate of flow from one device to another. bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system.
PORTÉGÉ M780 COM1, COM2, COM3 and COM4: The names assigned to the serial and communication ports. commands: Instructions you enter at the terminal keyboard that direct the actions of the computer or its peripheral devices. communications: The means by which a computer transmits and receives data to and from another computer or device. See serial interface.
PORTÉGÉ M780 data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions.
PORTÉGÉ M780 DVD-RW (+RW, -RW): A Digital Versatile Disc-ReWritable disc can be rewritten many times. DVD+R (Double Layer): A disc having two layers on one side with the DVD+R storage capacity about 1.8 times larger than before. The DVD-RW drive uses a laser to read data from the disc. E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both.
PORTÉGÉ M780 format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. function keys: The keys labeled F1 through F12 that tell the computer to perform certain functions. G gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. graphics: Drawings, pictures, or other images, such as charts or graphs, to present information.
PORTÉGÉ M780 instruction: Statements or commands that specify how to perform a particular task. interface: 1) Hardware and/or software components of a system used specifically to connect one system or device to another. 2) To physically connect one system or device to another to exchange information. 3) The point of contact between user, the computer, and the program, for example, the keyboard or a menu. interrupt request: A signal that gives a component access to the processor. I/O: Input/output.
PORTÉGÉ M780 LSI: Large Scale Integration. 1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip. 2) An integrated circuit that uses large scale integration. M main board: See motherboard. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen.
PORTÉGÉ M780 O OCR: Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device. online state: A functional state of a peripheral device when it is ready to receive or transmit data. operating system: A group of programs that controls the basic operation of a computer.
PORTÉGÉ M780 printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached. The board itself is typically flat and rectangular, and constructed of fiberglass, to form the attachment surface. program: A set of instructions a computer can execute that enables it to achieve a desired result. See also application. prompt: A message the computer provides indicating it is ready for or requires information or an action from you.
PORTÉGÉ M780 soft key: Key combinations that emulate keys on the IBM keyboard, change some configuration options, stop program execution, and access the numeric keypad overlay. software: The set of programs, procedures and related documentation associated with a computer system. Specifically refers to computer programs that direct and control the computer system’s activities. See also hardware.
PORTÉGÉ M780 W warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. Wireless LAN: Local Area Network (LAN) through wireless communication. Wireless WAN: Wide Area Network (WAN) through wireless communication. write protection: A method for protecting a floppy diskette from accidental erasure.
PORTÉGÉ M780 Index A AC adaptor, 3-3 additional, 3-45 connecting, 1-4 ASCII characters, 5-7 B Battery charging, 6-7 extending life, 6-10 indicator, 2-14, 6-4 monitoring capacity, 6-8 real time clock, 3-3, 6-6 save mode, 3-7 types, 6-5 Battery pack, 2-8, 3-2 additional, 3-46 replacing, 6-10 Bluetooth, 3-5, 4-53 Bluetooth Stack for Windows by Toshiba, 3-12 problems, 8-24 Bridge media slot, 2-4, 3-18 indicator, 2-14 using, 3-18 C Cleaning the computer, 4-57 Cooling vents, 2-3 D DC IN indicator, 2-13, 6-4 D
PORTÉGÉ M780 FN + F5 (Output), 5-4 FN + F6 (Brightness Down), 5-4 FN + F7 (Brightness Up), 5-4 FN + F8 (Wireless), 5-4 FN + F9 (Touch Pad), 5-4 FN + space (Zoom), 5-4 FN + Tab (ODD), 5-5 Function keys, 5-2 SATA, 7-7 USB, 7-6 window, 7-1 I Graphics controller, 3-4 i.
PORTÉGÉ M780 Memory, 3-1 additional, 3-45 installing, 3-24, 3-29 problems, 8-19 removing, 3-28, 3-31 Memory Stick, 3-19 problems, 8-12 Modem, 3-5, 4-48 connecting, 4-50 disconnecting, 4-51 jack, 2-5 problems, 8-22 properties menu, 4-49 region selection, 4-49 Moving the computer, 4-57 MultiMediaCard, 3-19 problems, 8-13 P Password power on, 3-7 problems, 8-7 Starting the computer by, 6-16 Supervisor, 6-16 user, 6-15 Pointing Device problems, 8-14 Tablet PC Pen, 4-2 Touch Pad, 2-12, 4-1 Touch Pad control bu
PORTÉGÉ M780 Soft keys enhanced keyboard, 5-2 ENTER, 5-3 ScrLock, 5-3 Sound system headphone jack, 2-2 microphone, 2-13 microphone jack, 2-2 problems, 8-20 Stereo speakers, 2-12 volume control dial, 2-2 T TOSHIBA Assist, 3-13 TOSHIBA Assist button, 3-6 TOSHIBA ConfigFree, 3-13 TOSHIBA Disc Creator, 3-13, 4-41 TOSHIBA DVD-RAM Utility, 3-14 TOSHIBA Express Port Replicator, 3-44, 3-46 TOSHIBA HDD Protection, 3-8, 4-58 TOSHIBA PC Diagnostic Tool, 3-10 TOSHIBA Presentation button, 3-6 TOSHIBA Theft Registratio
